Text-to-speech technologies are evolving quickly towards realistic-sounding human-like voices. As this technology improves, so does the opportunity for malpractice in speaker identification (SID) via spoofing, the process of impersonating a voice biometric via synthesis. More data typically equates to a more realistic voice model, which poses an issue for well-known subjects, such as politicians and celebrities, who have vast amounts of multimedia available online. Detection of synthetic speech has relied on signal processing techniques that focus on the generation of new acoustic features and train deep learning models to detect when an audio file has been manipulated through the characterization of unnatural changes or artifacts. However, these techniques do not use any information from the speaker they are evaluating. This paper proposes to incorporate information from the speaker-of-interest (SoI) into the models to avoid specific spoofing attacks for certain vulnerable people. The wealth of data for well-known people can also be used to train a speaker-specific spoofing detector with a higher level of accuracy than a speaker-independent model. The paper proposes a new xResNet-PLDA system and compares it to three different baseline systems: a state-of-the-art speaker identification system, an xResNet system trained to discriminate between bona fide and fake speech, and a speaker identification system in which the PLDA and calibration models were trained with bona fide and fake speech. We evaluated the systems in two different scenarios — a cross-validation scenario and a hold-out scenario — with three different databases. We show how the proposed system outperforms dramatically the baseline systems in each scenario and for each database. Finally, we show how using a small amount of the SoI’s speech to adapt global calibration parameters improves the performance of the system, especially in unseen conditions.
Triangle counting is a fundamental building block in graph algorithms. In this article, we propose a block-based triangle counting algorithm to reduce data movement during both sequential and parallel execution. Our block-based formulation makes the algorithm naturally suitable for heterogeneous architectures. The problem of partitioning the adjacency matrix of a graph is well-studied. Our task decomposition goes one step further: it partitions the set of triangles in the graph. By streaming these small tasks to compute resources, we can solve problems that do not fit on a device. We demonstrate the effectiveness of our approach by providing an implementation on a compute node with multiple sockets, cores and GPUs. The current state-of-the-art in triangle enumeration processes the Friendster graph in 2.1 seconds, not including data copy time between CPU and GPU. Using that metric, our approach is 20 percent faster. When copy times are included, our algorithm takes 3.2 seconds. This is 5.6 times faster than the fastest published CPU-only time.
This paper compares four different formulations of model predictive control that attempt to maximise electrical power generated by a wave energy converter (WEC). Control laws include (1) pure maximisation of mechanical power, (2) maximisation of mechanical power with a control penalty factor, (3) maximisation of electrical power using power conversion efficiency, and (4) maximisation of electrical power using the full electro-mechanical model of a system. For this study, a wave-to-wire model is developed for a floating spherical buoy connected to a permanent magnet synchronous generator. The performance of the controllers, including the mechanical and electrical power outputs, is compared in irregular wave conditions for the unconstrained and force-constrained scenarios. The results demonstrate that the controller designed to maximise mechanical power is not suitable for practical applications and may lead to negative electrical power output due to the non-ideal power take-off efficiency. Moreover, the replacement of the power take-off dynamics by the efficiency coefficient does not guarantee the maximum electrical power production.
Material produced by current metal additive manufacturing processes is susceptible to variable performance due to imprecise control of internal porosity, surface roughness, and conformity to designed geometry. Using a double U-notched specimen, we investigate the interplay of nominal geometry and porosity in determining ductile failure characteristics during monotonic tensile loading. We simulate the effects of distributed porosity on plasticity and damage using a statistical model based on populations of pores visible in computed tomography scans and additional sub-threshold voids required to match experimental observations of deformation and failure. We interpret the simulation results from a physical viewpoint and provide a statistical model of the probability of failure near stress concentrations. We provide guidance for designs where material defects could cause unexpected failures depending on the relative importance of these defects with respect to features of the nominal geometry.
Magnetized Liner Inertial Fusion (MagLIF) [Slutz et al., Phys. Plasmas 17, 056303 (2010)] experiments driven by the Z machine produce >1013 deuterium-deuterium fusion reactions [Gomez et al., Phys. Rev. Lett. 125, 155002 (2020)]. Simulations indicate high yields and gains (1000) with increased current and deuterium-tritium layers for burn propagation [Slutz et al., Phys. Plasmas 23, 022702 (2016)]. Such a coating also isolates the metal liner from the gaseous fuel, which should reduce mixing of liner material into the fuel. However, the vapor density at the triple point is only 0.3 kg/m3, which is not high enough for MagLIF operation. We present two solutions to this problem. First, a fuel wetted low-density plastic foam can be used to form a layer on the inside of the liner. The desired vapor density can be obtained by controlling the temperature. This does however introduce carbon into the layer which will enhance radiation losses. Simulations indicate that this wetted foam layer can significantly contribute to the fusion yield when the foam density is less than 35 kg/m3. Second, we show that a pure frozen fuel layer can first be formed on the inside of the liner and then low temperature gaseous fuel can be introduced just before the implosion without melting a significant amount of the ice layer. This approach is the most promising for MagLIF to produce high yield and gain.
With a wide variety of wave energy device archetypes currently under consideration, it is a major challenge to ensure that research findings and methods are broadly applicable. In particular, the design and testing of wave energy control systems, a process which includes experimental design, empirical modeling, control design, and performance evaluation, is of interest. This goal motivated the redesign and testing of a floating dual flap wave energy converter. As summarized in this paper, the steps taken in the design, testing, and analysis of the device mirrored those previously demonstrated on a three-degree of freedom point absorber device. The method proposed does not require locking WEC degrees of freedom to develop an excitation model, and presents a more attainable system identification procedure for at-sea deployments. The results show that the methods employed work well for this dual flap device, lending additional support for the broad applicability of the design and testing methods applied here. The aim of this paper is to demonstrate that these models are particularly useful for deducing areas of device design or controller implementation that can be reasonably improved to increase device power capture.
Poondla, Yasvanth; Goldstein, David; Varghese, Philip; Clarke, Peter; Moore, Christopher H.
The goal of this work is to build up the capability of quasi-particle simulation (QuiPS), a novel flow solver, such that it can adequately model the rarefied portion of an atmospheric reentry trajectory. Direct simulation Monte Carlo (DSMC) is the conventional solver for such conditions, but struggles to resolve transient flows, trace species, and high-level internal energy states due to stochastic noise. Quasi-particle simulation (QuiPS) is a novel Boltzmann solver that describes a system with a discretized, truncated velocity distribution function. The resulting fixed-velocity, variable weight quasi-particles enable smooth variation of macroscopic properties. The distribution function description enables the use of a variance-reduced collision model, greatly minimizing expense near equilibrium. This work presents the addition of a neutral air chemistry model to QuiPS and some demonstrative 0D simulations. The explicit representation of internal distributions in QuiPS reveals some of the flaws in existing physics models. Variance reduction, a key feature of QuiPS, can greatly reduce expense of multi-dimensional calculations, but is only cheaper when the gas composition is near chemical equilibrium.
We used the CTH shock physics code to simulate the explosion of an 18-t chemical explosive at a depth of 250 m. We used the CTH in the two-dimensional axisymmetric (cylindrical) geometry (2DC) and most simulations included fully tamped explosions in wet tuff. Our study focused on parametric studies of three of the traditional strength models available in CTH, namely, geologic-yield, elastic perfectly-plastic von Mises, and Johnson-Cook strength (flow stress) models. We processed CTH results through a code that generates Reduced Displacement Potential (RDP) histories for each simulation. Since RDP is the solution of the linear wave equation in spherical coordinates, it is mainly valid at far-enough distance from the explosion the elastic radius. Among various parameters examined, we found the yield strength to have the greatest effect on the resulting RDP, where the peak RDP reduces almost linearly in log-log space as the yield strength increases. Moreover, an underground chemical explosion results in a cavity whose final diameter is inversely proportional to the material yield strength, i.e., as the material's yield strength increases the resulting final cavity radius decreases. Additionally, we found the choice of explosive material (COMP-C4 versus COMP-B) has minor effects on the peak RDP, where denser COMP-C4 shows higher peak RDP than the less dense COMP-B by a factor of ~1.1. In addition to wet tuff, we studied explosions in dry tuff, salt, and basalt, for a single strength model and yield strength value. We found wet tuff has the highest peak RDP value, followed by dry tuff, salt, and basalt. 2DC simulations of explosions in 11 m radius spherical, hemispherical, and cylindrical cavities showed the RDP signals have much lower magnitude than tamped explosions, where the cavity explosions mimicked nearly decoupled explosions.
The purpose of the Sandia CIO Cloud Strategy is to establish the strategic direction for the adoption of cloud services and technologies as the prevailing IT solution for Sandia National Laboratories. Sandia’s Chief Information Officer (CIO) will champion unified, site-wide adoption of cloud and will amplify business and mission impacts across the Labs. Sandia’s CIO Cloud Strategy aligns to the Federal Cloud Computing Strategy1 (Cloud Smart) and the Sandia Management and Operating Contract (Prime Contract).
An improved electrical contact resistance (ECR) model for elastic rough electrode contact is proposed, incorporating the effects of asperity interactions and temperature rise by frictional and joule heating. The analytical simulation results show that the ECR decreases steeply at the beginning of the contact between Al and Cu. However, it becomes stabilized after reaching a specific contact force. It is also found that the longer elapsed sliding contact time, the higher ECR due to the increase in electrical resistivity of electrode materials by the frictional temperature rise at the interface. The effects of surface roughness parameters on ECR are studied through the 32 full-factorial design-of-experiment analysis. Based on the two representative roughness parameters, i.e., root-mean-square (rms) roughness and asperity radius, their individual and coupled effects on the saturated ECR are examined. The saturated ECR increases with the rms roughness for a rough machined surface condition, but it is hardly affected by the asperity radius. On the other hand, the saturated ECR increases with both the rms roughness and the asperity radius under a smooth thin film surface condition.
This is the final Technical Report for DOE-SETO Project Award # DE-EE0036461. The goal of this project is to advance the understanding of the grid impact of high penetration of photovoltaic (PV) generation by developing novel numerical methods to solve the differential algebraic equations (DAEs) that define power systems. This will overcome the limitations of current software packages – namely that they only consider fast dynamics over brief time periods. The work presented in this final project report covers results over the entire period of the project. This includes results on model development, code development for the PST repository, datasets in the PST repository, algorithm development and results from variable time-step simulations, development and results from multirate simulations, and sensitivity analysis of key parameter in variable time-step methods. In addition, this report discusses project outreach activities to stakeholders, and a summary of project products. Also covered in this final report is the writing of two conference papers (one of which has already been accepted) and a journal paper. In addition, the updating of two inverter models (both grid forming and grid following) to be compatible with the latest version of PST software is discussed.
D'Elia, Marta D.; Darve, Eric; Garrappa, Roberto; Giusti, Andrea; Rubio, Natalia L.
We present a novel definition of variable-order fractional Laplacian on Rn based on a natural generalization of the standard Riesz potential. Our definition holds for values of the fractional parameter spanning the entire open set (0, n/2). We then discuss some properties of the fractional Poisson’s equation involving this operator and we compute the corresponding Green’s function, for which we provide some instructive examples for specific problems.
Agencies that monitor for underground nuclear tests are interested in techniques that automatically characterize mining blasts to reduce the human analyst effort required to produce high-quality event bulletins. Waveform correlation is effective in finding similar waveforms from repeating seismic events, including mining blasts. We report the results of an experiment to detect and identify mining blasts for two regions, Wyoming (U.S.A.) and Scandinavia, using waveform templates recorded by multiple International Monitoring System stations of the Preparatory Commission for the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO PrepCom) for up to 10 yr prior to the time of interest. We discuss approaches for template selection, threshold setting, and event detection that are specialized for characterizing mining blasts using a sparse, global network. We apply the approaches to one week of data for each of the two regions to evaluate the potential for establishing a set of standards for waveform correlation processing of mining blasts that can be generally applied to operational monitoring systems with a sparse network. We compare candidate events detected with our processing methods to the Reviewed Event Bulletin of the International Data Centre to assess potential reduction in analyst workload.
System emulation and firmware re-hosting have become popular techniques to answer various security and performance related questions, such as determining whether a firmware contain security vulnerabilities or meet timing requirements when run on a specific hardware platform. While this motivation for emulation and binary analysis has previously been explored and reported, starting to either work or research in the field is difficult. To this end, we provide a comprehensive guide for the practitioner or system emulation researcher. We layout common challenges faced during firmware re-hosting, explaining successive steps and surveying common tools used to overcome these challenges. We provide classification techniques on five different axes, including emulator methods, system type, fidelity, emulator purpose, and control. These classifications and comparison criteria enable the practitioner to determine the appropriate tool for emulation. We use our classifications to categorize popular works in the field and present 28 common challenges faced when creating, emulating, and analyzing a system from obtaining firmwares to post emulation analysis.
In 2018 13.7 EJ of fuel were consumed by the global commercial aviation industry. Worldwide, demand will increase into the foreseeable future. Developing Sustainable Aviation Fuels (SAFs), with decreased CO2 and soot emissions, will be pivotal to the on-going mitigation efforts against global warming. Minimizing aromatics in aviation fuel is desirable because of the high propensity of aromatics to produce soot during combustion. Because aromatics cause o-rings to swell, they are important for maintaining engine seals, and must be present in at least 8 vol% under ASTM-D7566. Recently, cycloalkanes have been shown to exhibit some o-ring swelling behavior, possibly making them an attractive substitute to decrease the aromatic content of aviation fuel. Cycloalkanes must meet specifications for a number of other physical properties to be compatible with jet fuel, and these properties can vary greatly with the cycloalkane chemical structure, making their selection difficult. Building a database of structure-property relationships (SPR) for cycloalkanes greatly facilitates their furthered inclusion into aviation fuels. The work presented in this paper develops SPRs by building a data set that includes physical properties important to the aviation industry. The physical properties considered are energy density, specific energy, melting point, density, flashpoint, the Hansen solubility parameter, and the yield sooting index (YSI). Further, our data set includes cycloalkanes drawn from the following structural groups: fused cycloalkanes, n-alkylcycloalkanes, branched cycloalkanes, multiple substituted cycloalkanes, and cycloalkanes with different ring sizes. In addition, a select number of cycloalkanes are blended into Jet-A fuel (POSF-10325) at 10 and 30 wt%. Comparison of neat and blended physical properties are presented. One major finding is that ring expanded systems, those with more than six carbons, have excellent potential for inclusion in SAFs. Our data also indicate that polysubstituted cycloalkanes have higher YSI values.
Zwier, Timothy S.; Hernandez-Castillo, A.O.; Calabrese, Camilla; Fritz, Sean M.; Uriarte, Iciar; Cocinero, Emilio J.
In this report broadband microwave spectra were recorded over the 2-18 GHz frequency range for a series of four model aromatic components of lignin; namely, guaiacol (ortho-methoxy phenol, G), syringol (2,6-dimethoxy phenol, S), 4-methyl guaiacol (MG), and 4-vinyl guaiacol (VG), under jet-cooled conditions in the gas phase. Using a combination of 13C isotopic data and electronic structure calculations, distortions of the phenyl ring by the substituents on the ring are identified. In all four molecules, the rC(1)-C(6) bond between the two substituted C-atoms lengthens, leading to clear bond alternation that reflects an increase in the phenyl ring resonance structure with double bonds at rC(1)-C(2), rC(3)-C(4) and rC(5)-C(6). Syringol, with its symmetric methoxy substituents, possesses a microwave spectrum with tunneling doublets in the a-type transitions associated with H-atom tunneling. These splittings were fit to determine a barrier to hindered rotation of the OH group of 1975 cm-1, a value nearly 50% greater than that in phenol, due to the presence of the intramolecular OH…OCH3 H-bonds at the two equivalent planar geometries. In 4-methyl guaiacol, methyl rotor splittings are observed and used to confirm and refine an earlier measurement of the three-fold barrier V3 = 67 cm-1. Finally, 4-vinyl guaiacol shows transitions due to two conformers differing in the relative orientations of the vinyl and OH groups.
Deep level defects in wide bandgap semiconductors, whose response times are in the range of power converter switching times, can have a significant effect on converter efficiency. We use deep level transient spectroscopy (DLTS) to evaluate such defect levels in the n-drift layer of vertical gallium nitride (v-GaN) power diodes with VBD ∼1500 V. DLTS reveals three energy levels that are at ∼0.6 eV (highest density), ∼0.27 eV (lowest density), and ∼45 meV (a dopant level) from the conduction band. Dopant extraction from capacitance-voltage measurement tests (C-V) at multiple temperatures enables trap density evaluation, and the ∼0.6 eV trap has a density of 1.2 × 1015 cm-3. The 0.6 eV energy level and its density are similar to a defect that is known to cause current collapse in GaN based surface conducting devices (like high electron mobility transistors). Analysis of reverse bias currents over temperature in the v-GaN diodes indicates a predominant role of the same defect in determining reverse leakage current at high temperatures, reducing switching efficiency.
The generating value from lignin through depolymerization and biological conversion to valuable fuels, chemicals, or intermediates has great promise but is limited by several factors including lack of cost-effective depolymerization methods, toxicity within the breakdown products, and low bioconversion of the breakdown products. High yield depolymerization of natural lignins requires cleaving carbon-carbon bonds in addition to ether bonds. To address that need, we report that a chelator-mediated Fenton reaction can efficiently cleave C-C bonds in sulfonated polymers at or near room temperature, and that unwanted repolymerization can be minimized through optimizing reaction conditions. This method was used to depolymerize lignosulfonate from Mw = 28,000 g/mol to Mw = 800 g/mol. The breakdown products were characterized by SEC, FTIR and NMR and evaluated for bioavailability. The breakdown products are rich in acid, aldehyde, and alcohol functionalities but are largely devoid of aromatics and aliphatic dienes. A panel of nine organisms were tested for the ability to grow on the breakdown products. Growth at a low level was observed for several monocultures on the depolymerized LS in absence of glucose. Much stronger growth was observed in the presence of 0.2% glucose and for one organism we demonstrate doubling of melanin production in the presence of depolymerized LS. The results suggest that this chelator-mediated Fenton method is a promising new approach for biological conversion of lignin into higher value chemicals or intermediates.
Composite structures inherently develop residual stresses during their curing process. Driven predominately by mismatched thermal strains between differing materials or ply orientations, but also affected by curing process phenomena like polymer shrinkage, these residual stresses can lead to failure within composite structures. There are several methods varying in complexity that can be used to model the development of residual stresses, all of which are capable of capturing sufficient detail to understand the residual stress state at the ply level. However, explicitly modeling all plies of a layup in a composite structure can be prohibitively expensive based on the number of plies, structure size, and required element size. The computational cost can be reduced through the homogenization of the composite layup without losing much fidelity of the overall response of the structure. The homogenization process reduces the many plies of a laminate to a single lamina that reduces complexity and increases the mesh size where a single element can span multiple plies. This report focuses on verification and validation efforts for a homogenization process using a suite of finite element simulations rather than an analytic solution derived from classical laminate theory. Initial verification using representative element volumes indicated there was minimal error in the homogenization process; however, this compounded to a small, but acceptable error in strip and split ring experimental composite structures. The error does under predict the residual stress state in the strip and split ring and should be accounted for when simulating composite structures with homogenized properties.
Sandia provided technical assistance to the Alaska Ocean Cluster to assess potential market opportunities regarding byproducts of crab in the greater Alaska region. Crab contains a wide variety of proteins, chitin, lipids, minerals, and pigments. Currently, only a small portion of these components are utilized, primarily proteins associated with crab meat. Sandia provided an assessment of the current market landscape and opportunities related to crab byproducts including market size and applications. Sandia subject matter experts conducted an analysis and provide the Alaska Ocean Cluster team with a report describing the state of research and market opportunities offered by Alaska crab byproducts. The final report focused on market opportunities regarding chitosan production, chitin extraction, as well as an overview of the key market players and applications.
A graph is a mathematical representation of a network; we say it consists of a set of vertices, which are connected by edges. Graphs have numerous applications in various fields, as they can model all sorts of connections, processes, or relations. For example, graphs can model intricate transit systems or the human nervous system. However, graphs that are large or complicated become difficult to analyze. This is why there is an increased interest in the area of graph partitioning, reducing the size of the graph into multiple partitions. For example, partitions of a graph representing a social network might help identify clusters of friends or colleagues. Graph partitioning is also a widely used approach to load balancing in parallel computing. The partitioning of a graph is extremely useful to decompose the graph into smaller parts and allow for easier analysis. There are different ways to solve graph partitioning problems. For this work, we focus on a spectral partitioning method which forms a partition based upon the eigenvectors of the graph Laplacian (details presented in Acer, et. al.). This method uses the LOBPCG algorithm to compute these eigenvectors. LOBPCG can be accelerated by an operator called a preconditioner. For this internship, we evaluate a randomized Cholesky (rchol) preconditioner for its effectiveness on graph partitioning problems with LOBPCG. We compare it with two standard preconditioners: Jacobi and Incomplete Cholesky (ichol). This research was conducted from August to December 2021 in conjunction with Sandia National Laboratories.
This all-inclusive document describes the components, installation, and usage of the Seascape system. Additionally, this manual outlines the step-by-step processes for setting up your own local instance of Seascape, incorporating new datasets and algorithms into Seascape, and how to use the system itself. A brief overview of Seascape is provided in Section 1.2. System components and the various roles of the intended users of the system are described in Section 1.3. Next, steps on how each role uses Seascape are explained in Section 2.1. Finally, the steps to incorporate data into Seascape-DB and an algorithm into Seascape-VV are outlined in Sections 2.2 and 2.3, respectively. Steps to set up an instance of Seascape can be found in Appendix A.1. Finally, Seascape usage can be found in Section 2.1. The appendix includes code examples, frequently asked questions, terminology, and a list of acronyms.
Understanding hydrogen incorporation into palladium requires detailed knowledge of surface and subsurface structure and atomic interactions as surface hydrogen is being embedded. Using density functional theory (DFT), we examine the energies of hydrogen layers of varying coverage adsorbed on Pd(111). Here we find that H–H and H–Pd interactions promote the formation of the well-known ($\sqrt{3}$ x $\sqrt{3}$) phases but also favor an unreported (3 × 3) phase at high H coverages for which we present experimental evidence. We relate the stability of isolated H vacancies of the (3 × 3) phase to the need of H2 molecules to access bare Pd before they can dissociate. Following higher hydrogen dosage, we observe initial steps of hydride formation, starting with small clusters of subsurface hydrogen. The interaction between H and Pd is complicated by the persistent presence of carbon at the surface. X-ray photoelectron spectroscopy experiments show that trace amounts of carbon, emerging from the Pd bulk despite many surface cleaning cycles, become mobile enough to repopulate the C-depleted surface at temperatures above 200 K. When exposed to hydrogen, these surface carbon atoms react to form benzene, as evidenced by scanning tunneling microscopy observations interpreted with DFT.
Hoglund, Eric R.; Bao, De-Liang; O'Hara, Andrew; Makarem, Sara; Piontkowski, Zachary T.; Matson, Joseph R.; Yadav, Ajay K.; Haislmaier, Ryan C.; Ihlefeld, Jon F.; Ravichandran, Jayakanth; Ramesh, Ramamoorthy; Caldwell, Joshua D.; Beechem, Thomas E.; Tomko, John; Hachtel, Jordan A.; Pantelides, Sokrates T.; Hopkins, Patrick E.; Howe, James M.
As the length scales of materials decrease, the heterogeneities associated with interfaces become almost as important as the surrounding materials. This has led to extensive studies of emergent electronic and magnetic interface properties in superlattices. However, the interfacial vibrations that affect the phonon-mediated properties, such as thermal conductivity, are measured using macroscopic techniques that lack spatial resolution. Although it is accepted that intrinsic phonons change near boundaries, the physical mechanisms and length scales through which interfacial effects influence materials remain unclear. Here we demonstrate the localized vibrational response of interfaces in strontium titanate–calcium titanate superlattices by combining advanced scanning transmission electron microscopy imaging and spectroscopy, density functional theory calculations and ultrafast optical spectroscopy. Structurally diffuse interfaces that bridge the bounding materials are observed and this local structure creates phonon modes that determine the global response of the superlattice once the spacing of the interfaces approaches the phonon spatial extent. Our results provide direct visualization of the progression of the local atomic structure and interface vibrations as they come to determine the vibrational response of an entire superlattice. Direct observation of such local atomic and vibrational phenomena demonstrates that their spatial extent needs to be quantified to understand macroscopic behaviour. Tailoring interfaces, and knowing their local vibrational response, provides a means of pursuing designer solids with emergent infrared and thermal responses.
This work presents an efficient data-driven protocol to accurately predict plastic anisotropy from initial crystallographic texture. In this work, we integrated feed forward neural networks with Variational Bayesian Inference techniques to establish an accurate low-computational cost surrogate model capable of predicting the anisotropic constants based on the texture of the polycrystalline material with quantifiable uncertainty. The developed model was trained on the results of 54,480 crystal plasticity simulations. The performed simulations parametrized Hill's anisotropic yield model for single crystals and polycrystalline textures, which were robustly represented using generalized spherical harmonics (GSH). Subsequently, the GSH-based representation of the different textures was linked to its corresponding Hill's anisotropic coefficients using a variational Bayesian neural network. The efficacy and accuracy of the developed surrogate model were critically validated with the results of 20,000 new textures. The predictions from the Bayesian neural network model showed excellent agreement with results obtained from experiments and high-fidelity crystal plasticity finite element simulations.
Sandia National Labs has created a noteworthy and effective internship program whose focus is creating a talent pipeline for the laboratory. Our program utilizes industry standard conversion calculations to examine the effectiveness of the program and to compare to our competitors. Sandia defines students eligible for conversion as graduating in the given fiscal year and in their final degree program. Students indicate to SIP upon hire and at certain checkpoints throughout their internship if they are in their final degree program or not. This means that they will not continue to a higher degree program after they graduate. For instance, someone who is graduating with a master’s degree in the current FY and does not plan to pursue a PhD would be considered eligible, while an undergrad student who is graduating in the same year, but plans to pursue a graduate degree, would not be considered eligible for conversion. Conversion data pulled for this report includes all eligible interns for fiscal year 2021. We use a rolling population, which includes anyone who was an intern at some point during FY21. To calculate conversion, we narrow our population down to the students who graduated between October 2020 through September 2021, who have indicated that they are in their final degree program. The conversion data was pulled on 10/29/2021, so any conversions completed after this date will not be included in the calculation. Our conversion data includes students who separated from Sandia and returned as a staff member. Conversions also include FTE, LTE, and postdoc positions. We do not include conversion to contractor positions in our calculations.
Baxter, Samuel J.; Schneemann, Andreas; Evans, Jack D.; Ready, Austin D.; Wilkinson, Angus P.; Burtch, Nicholas C.
Mechanisms underlying the mechanically induced amorphization of metal-organic frameworks (MOFs) are of current interest, and both high-pressure experimentation and molecular dynamics simulations have been used to reveal the fundamentals of load bearing, deformation, and pressure-induced amorphization (PIA) in these highly porous materials. Unfortunately, MOFs are typically highly susceptible to amorphization, which limits the conditions under which they can be processed and used. However, their flexible structures can be stabilized at high pressures by incorporating guest species into the framework matrix. In this study, a large-molecule pressure transmitting medium (DAPHNE 7575) is used as a structure-fortifying guest species to stabilize the prototypical MOF-5 at high pressures (>9 GPa) and enable the recovery of crystalline material upon decompression. Structural changes associated with the penetration of the pressure transmitting medium on compression are examined using a combination of high-pressure synchrotron powder diffraction and molecular dynamics simulations. This work enhances the understanding of PIA in MOFs while showcasing a potential route for the stabilization of MOFs at surprisingly high pressures.
Alloying is often employed to stabilize nanocrystalline materials against microstructural coarsening. The stabilization process results from the combined effects of thermodynamically reducing the curvature-dominated driving force of grain-boundary motion via solute segregation and kinetically pinning these same grain boundaries by solute drag and Zener pinning. The competition between these stabilization mechanisms depends not only on the grain-boundary character but can also be affected by imposed compositional and thermal fields that further promote or inhibit grain growth. In this work, we study the origin of the stability of immiscible nanocrystalline alloys in both homogeneous and heterogeneous compositional and thermal fields by using a multi-phase-field formulation for anisotropic grain growth with grain-boundary character-dependent segregation properties. This generalized formulation allows us to model the distribution of mobilities of segregated grain boundaries and the role of grain-boundary heterogeneity on solute-induced stabilization. As an illustration, we compare our model predictions to experimental results of microstructures in platinum-gold nanocrystalline alloys. Our results reveal that increasing the initial concentration of available solute progressively slows the rate of grain growth via both heterogeneous grain-boundary segregation and Zener pinning, while increasing the temperature generally weakens thermodynamic stabilization effects due to entropic contributions. Finally, we demonstrate as a proof-of-concept that spatially-varying compositional and thermal fields can be used to construct dynamically-stable, graded, nanostructured materials. We discuss the implications of using such concepts as alternatives to conventional plastic deformation methods.
We propose a novel statistical inference paradigm for zero-inflated multiway count data that dispenses with the need to distinguish between true and false zero counts. Our approach ignores all zero entries and applies zero-truncated Poisson regression on the positive counts. Inference is accomplished via tensor completion that imposes low-rank structure on the Poisson parameter space. Our main result shows that an $\textit{N}$-way rank-R parametric tensor 𝓜 ϵ (0, ∞)$I$Χ∙∙∙Χ$I$ generating Poisson observations can be accurately estimated from approximately $IR^2 \text{log}^2_2(I)$ non-zero counts for a nonnegative canonical polyadic decomposition. Several numerical experiments are presented demonstrating that our zero-truncated paradigm is comparable to the ideal scenario where the locations of false zero counts are known $\textit{a priori}$.
The following report summarizes the status update during this quarter for the National Nuclear Security Agency (NNSA) initiated Minority Serving Institution Partnership Plan's (MSIPP) project titled, Partnership for Advanced Manufacturing Education and Research (PAMER). In 2016, the National Nuclear Security Agency (NNSA) initiated the Minority Serving Institution Partnership Plan (MSIPP) targeting Tribal Colleges and Universities (TCUs) to offer programs that will prepare students for technical careers in NNSA’s laboratories and production plants. The MSIPP consortium’s approach is as follows: 1) align investments at the college and university level to develop a curriculum and workforce needed to support NNSA’s nuclear weapon enterprise mission, and 2) to enhance research and education at under-represented colleges and universities.
The Machine Learning for Correlated Intelligence Laboratory Directed Research & Development (LDRD) Project explored competing a variety of machine learning (ML) classification techniques against a known, open source dataset through the use of a rapid and automated algorithm research & development (RD) infrastructure. This approach relied heavily on creating an infrastructure in which to provide a pipeline for automatic target recognition (ATR) ML algorithm competition. Results are presented for nine ML classifiers against a primary dataset using the pipeline infrastructure developed for this project. New approaches to feature set extraction are presented and discussed as well.
Anomalous behavior is ubiquitous in subsurface solute transport due to the presence of high degrees of heterogeneity at different scales in the media. Although fractional models have been extensively used to describe the anomalous transport in various subsurface applications, their application is hindered by computational challenges. Simpler nonlocal models characterized by integrable kernels and finite interaction length represent a computationally feasible alternative to fractional models; yet, the informed choice of their kernel functions still remains an open problem. We propose a general data-driven framework for the discovery of optimal kernels on the basis of very small and sparse data sets in the context of anomalous subsurface transport. Using spatially sparse breakthrough curves recovered from fine-scale particle-density simulations, we learn the best coarse-scale nonlocal model using a nonlocal operator regression technique. Predictions of the breakthrough curves obtained using the optimal nonlocal model show good agreement with fine-scale simulation results even at locations and time intervals different from the ones used to train the kernel, confirming the excellent generalization properties of the proposed algorithm. A comparison with trained classical models and with black-box deep neural networks confirms the superiority of the predictive capability of the proposed model.
Nuclear spins were among the first physical platforms to be considered for quantum information processing1,2, because of their exceptional quantum coherence3 and atomic-scale footprint. However, their full potential for quantum computing has not yet been realized, owing to the lack of methods with which to link nuclear qubits within a scalable device combined with multi-qubit operations with sufficient fidelity to sustain fault-tolerant quantum computation. Here we demonstrate universal quantum logic operations using a pair of ion-implanted 31P donor nuclei in a silicon nanoelectronic device. A nuclear two-qubit controlled-Z gate is obtained by imparting a geometric phase to a shared electron spin4, and used to prepare entangled Bell states with fidelities up to 94.2(2.7)%. The quantum operations are precisely characterized using gate set tomography (GST)5, yielding one-qubit average gate fidelities up to 99.95(2)%, two-qubit average gate fidelity of 99.37(11)% and two-qubit preparation/measurement fidelities of 98.95(4)%. These three metrics indicate that nuclear spins in silicon are approaching the performance demanded in fault-tolerant quantum processors6. We then demonstrate entanglement between the two nuclei and the shared electron by producing a Greenberger–Horne–Zeilinger three-qubit state with 92.5(1.0)% fidelity. Because electron spin qubits in semiconductors can be further coupled to other electrons7–9 or physically shuttled across different locations10,11, these results establish a viable route for scalable quantum information processing using donor nuclear and electron spins.
Increasing growth in land-based wind turbine blades to enable higher machine capacities and capacity factors is creating challenges in design, manufacturing, logistics, and operation. Enabling further blade growth will require technology innovation. An emerging solution to overcome logistics constraints is to segment the blades spanwise and chordwise, which is effective, but the additional field-assembled joints result in added mass and loads, as well as increased reliability concerns in operation. An alternative to this methodology is to design slender flexible blades that can be shipped on rail lines by flexing during transport. However, the increased flexibility is challenging to accommodate with a typical glass-fiber, upwind design. In a two-part paper series, several design options are evaluated to enable slender flexible blades: downwind machines, optimized carbon fiber, and active aerodynamic controls. Part 1 presents the system-level optimization of the rotor variants as compared to conventional and segmented baselines, with a low-fidelity representation of the blades. The present work, Part 2, supplements the system-level optimization in Part 1 with high-fidelity blade structural optimization to ensure that the designs are at feasible optima with respect to material strength and fatigue limits, as well as global stability and structural dynamics constraints. To accommodate the requirements of the design process, a new version of the Numerical Manufacturing And Design (NuMAD) code has been developed and released. The code now supports laminate-level blade optimization and an interface to the International Energy Agency Wind Task 37 blade ontology. Transporting long, flexible blades via controlled flapwise bending is found to be a viable approach for blades of up to 100m. The results confirm that blade mass can be substantially reduced by going either to a downwind design or to a highly coned and tilted upwind design. A discussion of active and inactive constraints consisting of material rupture, fatigue damage, buckling, deflection, and resonant frequencies is presented. An analysis of driving load cases revealed that the downwind designs are dominated by loads from sudden, abrupt events like gusts rather than fatigue. Finally, an analysis of carbon fiber spar caps for downwind machines finds that, compared to typical carbon fibers, the use of a new heavy-tow carbon fiber in the spar caps is found to yield between 9% and 13% cost savings. Copyright:
Optical anticounterfeiting tags utilize the photoluminescent properties of materials to encode unique patterns, enabling identification and validation of important items and assets. These tags must combine optical complexity with ease of production and authentication to both prevent counterfeiting and to remain practical for widespread use. Metal-organic frameworks (MOFs) based on polynuclear, rare earth clusters are ideal materials platforms for this purpose, combining fine control over structure and composition, with tunable, complex energy transfer mechanisms via both linker and metal components. Here we report the design and synthesis of a set of heterometallic MOFs based on combinations of Eu, Nd, and Yb with the tetratopic linker 1,3,6,8-tetrakis(4-carboxyphenyl)pyrene. The energetics of this linker facilitate the intentional concealment of the visible emissions from Eu while retaining the infrared emissions of Nd and Yb, creating an optical tag with multiple covert elements. Unique to the materials system reported herein, we document the occurrence of a previously not observed 11-metal cluster correlated with the presence of Yb in the MOFs, coexisting with a commonly encountered 9-metal cluster. We demonstrate the utility of these materials as intricate optical tags with both rapid and in-depth screening techniques, utilizing orthogonal identifiers across composition, emission spectra, and emission decay dynamics. This work highlights the important effect of linker selection in controlling the resulting photoluminescent properties in MOFs and opens an avenue for the targeted design of highly complex, multifunctional optical tags.
High-protein algal biomass is an important bio-commodity that has the potential to provide a new source of sustainable protein products. Herein is a critical review that identifies (1) the most relevant sustainability findings related to the processing of proteinaceous algal biomass to higher value protein products and (2) the potential pathways to improve life cycle assessment (LCA) and techno-economic analysis (TEA) metrics, including life-cycle carbon dioxide equivalent (CO2eq), life cycle energy, and minimum selling price (MSP) of these products. The critical review of the literature revealed a large variation in model input parameters relating to these metrics. Therefore, a Monte Carlo analysis was conducted to assess the risk associated with these input variations. To understand the uncertainties that propagate into high-protein algae to products' systems, we reviewed more than 20 state-of-the-art unit operations for algal biomass processing., including cell disruption, protein solubilization, protein precipitation and purification, and protein concentration. We evaluated displacement of proteinaceous products by algal-bioproducts, including ruminant feed, aquaculture feed, protein tablets, and biopolymers and biopolyesters, with prices in the market ranging from 1.9 to 120 $ kg―1 protein. This review realized that the MSP of ruminant and non-ruminant feed ranges from 0.65 ± 0.56 to 2.9 ± 1.1 $ kg―1 protein, and bioplastics' MSP ranges from 0.97 to 7.0 $ kg―1 protein. Regarding LCA metrics, there is limited research on life cycle energy in proteinaceous biomass concentration and bioproduct systems, reported at 32.7 MJ kgprotein―1, for animal feed displacement. Animal feed emissions in the literature report negative fluxes, representing environmental benefits, as low as ―3.7 kgCO2eq kg―1 protein and positive fluxes, i.e., global warming potential, as high as 12.8 kgCO2eq kg―1 protein. There is limited research on bioplastics life cycle emissions reported at 0.6 kgCO2eq kg―1 protein. In general, the studies to date of algae-derived protein bioproducts showed similar life cycle emissions to soybean meals, nylon, polymers, and polystyrenes. Our risk analysis realized that more than 50% of scenarios can result in negative-net life cycle CO2eq emissions. This review and risk analysis assess and demonstrate the scenarios that improve economic and environmental sustainability metrics in high-protein algal bioproduct systems.
We present a framework for calibration of parameters in elastoplastic constitutive models that is based on the use of automatic differentiation (AD). The model calibration problem is posed as a partial differential equation-constrained optimization problem where a finite element (FE) model of the coupled equilibrium equation and constitutive model evolution equations serves as the constraint. The objective function quantifies the mismatch between the displacement predicted by the FE model and full-field digital image correlation data, and the optimization problem is solved using gradient-based optimization algorithms. Forward and adjoint sensitivities are used to compute the gradient at considerably less cost than its calculation from finite difference approximations. Through the use of AD, we need only to write the constraints in terms of AD objects, where all of the derivatives required for the forward and inverse problems are obtained by appropriately seeding and evaluating these quantities. We present three numerical examples that verify the correctness of the gradient, demonstrate the AD approach's parallel computation capabilities via application to a large-scale FE model, and highlight the formulation's ease of extensibility to other classes of constitutive models.
The controlled fabrication of vertical, tapered, and high-aspect ratio GaN nanowires via a two-step top-down process consisting of an inductively coupled plasma reactive ion etch followed by a hot, 85% H3PO4 crystallographic wet etch is explored. The vertical nanowires are oriented in the [0001] direction and are bound by sidewalls comprising of 3362 ¯ } semipolar planes which are at a 12° angle from the [0001] axis. High temperature H3PO4 etching between 60 °C and 95 °C result in smooth semipolar faceting with no visible micro-faceting, whereas a 50 °C etch reveals a micro-faceted etch evolution. High-angle annular dark-field scanning transmission electron microscopy imaging confirms nanowire tip dimensions down to 8–12 nanometers. The activation energy associated with the etch process is 0.90 ± 0.09 eV, which is consistent with a reaction-rate limited dissolution process. The exposure of the 3362 ¯ } type planes is consistent with etching barrier index calculations. The field emission properties of the nanowires were investigated via a nanoprobe in a scanning electron microscope as well as by a vacuum field emission electron microscope. The measurements show a gap size dependent turn-on voltage, with a maximum current of 33 nA and turn-on field of 1.92 V nm−1 for a 50 nm gap, and uniform emission across the array.
Heidari-Koochi, Milad; Karathanassis, Ioannis K.; Koukouvinis, Phoevos; Hwang, Joonsik; Pickett, Lyle M.; Spivey, David
Research on renewable and alternative fuels is crucial for improving the energy and environmental efficiency of modern gasoline internal combustion engines. To highlight the influence of fuel rheological and thermodynamic properties on phase change and atomisation processes, three types of gasoline blends were tested. More specifically, the campaign comprised a reference gasoline, an ethanol/gasoline blend (10% v/v) representative of renewable fuels, and an additised gasoline sample treated with viscoelasticity-inducing agents. High-speed imaging of the transient two-phase flow field arising in the internal geometry and the near-nozzle spray region of gasoline injectors was performed employing Diffuse Backlight Illumination. The metallic body of a commercial injector was modified to fit transparent tips realising two nozzle layouts, namely a two-hole real size model resembling the Engine Combustion Network spray G injector and an enraged replica with an offset hole. Experiments were conducted at realistic operating conditions comprising an injection pressure of 100 bar and ambient pressures in the range of 0.1–6.0 bar to cover the entire range of chamber pressures prevailing in Gasoline Direct Injection engines. The action of viscoelastic additives was verified to have a suppressive effect on in-nozzle cavitation (6% reduction in cavitation extent), while also enhancing spray atomisation at flash-boing conditions, in a manner resembling the more volatile gasoline/ethanol blends. Finally, persisting liquid ligaments were found to form after the end of injection for the additised sample, owing to the surfactant nature of the additives.
Abstract: In this study, dense bulk iron nitrides (FexN) were synthesized for the first time ever using spark plasma sintering (SPS) of FexN powders. The Fe4N phase of iron nitride in particular has significant potential to serve as a new soft magnetic material in both transformer and inductor cores and electrical machines. The density of SPSed FexN increased with SPS temperature and pressure. The microstructure of the consolidated bulk FexN was characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and superconducting quantum interference device (SQUID) magnetometry. XRD revealed a primary phase of Fe4N with secondary phases of Fe3N and metallic iron. Finite element analysis (FEA) was also applied to investigate and explain localized heating and temperature distribution during SPS. The effects of processing on interface bonding formation and phase evolution were investigated and discussed in detail to provide insight into fundamental phenomena and microstructural evolution in SPSed FexN. Graphic abstract: [Figure not available: see fulltext.]
Hahn, Nathan H.; Self, Julian; Driscoll, Darren M.; Dandu, Naveen; Han, Kee S.; Murugesan, Vijayakumar; Mueller, Karl T.; Curtiss, Larry A.; Balasubramanian, Mahalingam; Persson, Kristin A.; Zavadil, Kevin R.
Ion interactions strongly determine the solvation environments of multivalent electrolytes even at concentrations below that required for practical battery-based energy storage. This statement is particularly true of electrolytes utilizing ethereal solvents due to their low dielectric constants. These solvents are among the most commonly used for multivalent batteries based on reactive metals (Mg, Ca) due to their reductive stability. Recent developments in multivalent electrolyte design have produced a variety of new salts for Mg2+ and Ca2+ that test the limits of weak coordination strength and oxidative stability. Such electrolytes have great potential for enabling full-cell cycling of batteries based on these working ions. However, the ion interactions in these electrolytes exhibit significant and non-intuitive concentration relationships. In this work, we investigate a promising exemplar, calcium tetrakis(hexafluoroisopropoxy)borate (Ca(BHFIP)2), in the ethereal solvents 1,2-dimethoxyethane (DME) and tetrahydrofuran (THF) across a concentration range of several orders of magnitude. Surprisingly, we find that effective salt dissociation is lower at relatively dilute concentrations (e.g. 0.01 M) than at higher concentrations (e.g. 0.2 M). Combined experimental and computational dielectric and X-ray spectroscopic analyses of the changes occurring in the Ca2+ solvation environment across these concentration regimes reveals a progressive transition from well-defined solvent-separated ion pairs to de-correlated free ions. This transition in ion correlation results in improvements in both conductivity and calcium cycling stability with increased salt concentration. Comparison with previous findings involving more strongly associating salts highlights the generality of this phenomenon, leading to important insight into controlling ion interactions in ether-based multivalent battery electrolytes.
Krylov subspace recycling is a powerful tool when solving a long series of large, sparse linear systems that change only slowly over time. In PDE constrained shape optimization, these series appear naturally, as typically hundreds or thousands of optimization steps are needed with only small changes in the geometry. In this setting, however, applying Krylov subspace recycling can be a difficult task. As the geometry evolves, in general, so does the finite element mesh defined on or representing this geometry, including the numbers of nodes and elements and element connectivity. This is especially the case if re-meshing techniques are used. As a result, the number of algebraic degrees of freedom in the system changes, and in general the linear system matrices resulting from the finite element discretization change size from one optimization step to the next. Changes in the mesh connectivity also lead to structural changes in the matrices. In the case of re-meshing, even if the geometry changes only a little, the corresponding mesh might differ substantially from the previous one. Obviously, this prevents any straightforward mapping of the approximate invariant subspace of the linear system matrix (the focus of recycling in this work) from one optimization step to the next; similar problems arise for other selected subspaces. In this paper, we present an algorithm to map an approximate invariant subspace of the linear system matrix for the previous optimization step to an approximate invariant subspace of the linear system matrix for the current optimization step, for general meshes. This is achieved by exploiting the map from coefficient vectors to finite element functions on the mesh, combined with interpolation or approximation of functions on the finite element mesh. We demonstrate the effectiveness of our approach numerically with several proof of concept studies for a specific meshing technique.
Doucet, Mathieu; Browning, James F.; Doyle, Barney L.; Charlton, Timothy R.; Ambaye, Haile; Seo, Joohyun; Mazza, Alessandro R.; Wenzel, John F.; Burns, George B.; Wixom, Ryan R.; Veith, Gabriel M.
Haynes 230 nickel alloy is one of the main contenders for salt containment in the design of thermal energy storage systems based on molten salts. A key problem for these systems is understanding the corrosion phenomena at the alloy–salt interface, and, in particular, the role played by chromium in these processes. In this study, thin films of Haynes 230, which is also rich in chromium, were measured with polarized neutron reflectometry and Rutherford backscattering spectrometry as a function of annealing temperature. Migration of chromium to the surface was observed for films annealed at 400 and 600 °C. Combining the two techniques determined that more than 60% of chromium comprising the as-prepared Haynes 230 layer moves to the surface when annealed at 600 °C, where it forms an oxide layer.
Luo, Chaoqian; Chung, Christopher; Yakacki, Christopher M.; Long, Kevin N.; Yu, Kai
Liquid crystal elastomers (LCEs) exhibit soft elasticity due to the alignment and reorientation of mesogens upon mechanical loading, which provides additional mechanisms to absorb and dissipate energy. This enhanced response makes LCEs potentially transformative materials for biomedical devices, tissue replacements, and protective equipment. However, there is a critical knowledge gap in understanding the highly rate-dependent dissipative behaviors of LCEs due to the lack of real-time characterization techniques that probe the microscale network structure and link it to the mechanical deformation of LCEs. In this work, we employ in situ optical measurements to evaluate the alignment and reorientation degree of mesogens in LCEs. The data are correlated to the quantitative physical analysis using polarized Fourier-transform infrared spectroscopy. The time scale of mesogen alignment is determined at different strain levels and loading rates. The mesogen reorientation kinetics is characterized to establish its relationship with the macroscale tensile strain, and compared to theoretical predictions. Overall, this work provides the first detailed study on the time-dependent evolution of mesogen alignment and reorientation in deformed LCEs. It also provides an effective and more accessible approach for other researchers to investigate the structural-property relationships of different types of polymers.
Graphite electrodes in the lithium-ion battery exhibit various particle shapes, including spherical and platelet morphologies, which influence structural and electrochemical characteristics. It is well established that porous structures exhibit spatial heterogeneity, and the particle morphology can influence transport properties. The impact of the particle morphology on the heterogeneity and anisotropy of geometric and transport properties has not been previously studied. This study characterizes the spatial heterogeneities of 18 graphite electrodes at multiple length scales by calculating and comparing the structural anisotropy, geometric quantities, and transport properties (pore-scale tortuosity and electrical conductivity). We found that the particle morphology and structural anisotropy play an integral role in determining the spatial heterogeneity of directional tortuosity and its dependency on pore-scale heterogeneity. Our analysis reveals that the magnitude of in-plane and through-plane tortuosity difference influences the multiscale heterogeneity in graphite electrodes.
The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Using MPMD coupling, Scefire and Nalu handle the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.
The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC re environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Using MPMD coupling, Scefire and Nalu handle the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.
Capacitance–voltage (C–V ) characteristics and carrier transport properties of 2-D electron gases (2DEGs) in an undoped Si/SiGe heterostructure at T = 4 – 35 K are presented here. In this work, two capacitance plateaus due to density saturation of the 2DEG in the buried Si quantum well (QW) are observed and explained by a model of surface tunneling. The peak mobility at 4 K is 4.1 × 105 cm2/V·s and enhanced by a factor of 1.97 at an even lower carrier density compared to the saturated carrier density, which is attributed to the effect of remote carrier screening. At T = 35 K, the mobility enhancement with a factor of 1.35 is still observed, which suggests the surface tunneling is still dominant.
Presented in this document is a portion of the tests that exist in the Sierra Thermal/Fluids verification test suite. Each of these tests is run nightly with the Sierra/TF code suite and the results of the test checked under mesh refinement against the correct analytic result. For each of the tests presented in this document the test setup, derivation of the analytic solution, and comparison of the code results to the analytic solution is provided. This document can be used to confirm that a given code capability is verified or referenced as a compilation of example problems.
The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Using MPMD coupling, Scefire and Nalu handle the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.
SIERRA/Aero is a compressible fluid dynamics program intended to solve a wide variety compressible fluid flows including transonic and hypersonic problems. This document describes the commands for assembling a fluid model for analysis with this module, henceforth referred to simply as Aero for brevity. Aero is an application developed using the SIERRA Toolkit (STK). The intent of STK is to provide a set of tools for handling common tasks that programmers encounter when developing a code for numerical simulation. For example, components of STK provide field allocation and management, and parallel input/output of field and mesh data. These services also allow the development of coupled mechanics analysis software for a massively parallel computing environment.
The SNL Sierra Mechanics code suite is designed to enable simulation of complex multiphysics scenarios. The code suite is composed of several specialized applications which can operate either in standalone mode or coupled with each other. Arpeggio is a supported utility that enables loose coupling of the various Sierra Mechanics applications by providing access to Framework services that facilitate the coupling. More importantly Arpeggio orchestrates the execution of applications that participate in the coupling. This document describes the various components of Arpeggio and their operability. The intent of the document is to provide a fast path for analysts interested in coupled applications via simple examples of its usage.
Sierra/SolidMechanics (Sierra/SM) is a Lagrangian, three-dimensional code for finite element analysis of solids and structures. It provides capabilities for explicit dynamic, implicit quasistatic and dynamic analyses. The explicit dynamics capabilities allow for the efficient and robust solution of models with extensive contact subjected to large, suddenly applied loads. For implicit problems, Sierra/SM uses a multi-level iterative solver, which enables it to effectively solve problems with large deformations, nonlinear material behavior, and contact. Sierra/SM has a versatile library of continuum and structural elements, and a large library of material models. The code is written for parallel computing environments enabling scalable solutions of extremely large problems for both implicit and explicit analyses. It is built on the SIERRA Framework, which facilitates coupling with other SIERRA mechanics codes. This document describes the functionality and input syntax for Sierra/SM.
Presented in this document are the theoretical aspects of capabilities contained in the Sierra / SM code. This manuscript serves as an ideal starting point for understanding the theoretical foundations of the code. For a comprehensive study of these capabilities, the reader is encouraged to explore the many references to scientific articles and textbooks contained in this manual. It is important to point out that some capabilities are still in development and may not be presented in this document. Further updates to this manuscript will be made as these capabilities come closer to production level.
Presented in this document is a small portion of the tests that exist in the Sierra/SolidMechanics (Sierra/SM) verification test suite. Most of these tests are run nightly with the Sierra/SM code suite, and the results of the test are checked versus the correct analytical result. For each of the tests presented in this document, the test setup, a description of the analytic solution, and comparison of the Sierra/SM code results to the analytic solution is provided. Mesh convergence is also checked on a nightly basis for several of these tests. This document can be used to confirm that a given code capability is verified or referenced as a compilation of example problems. Additional example problems are provided in the Sierra/SM Example Problems Manual. Note, many other verification tests exist in the Sierra/SM test suite, but have not yet been included in this manual.
Natural convection in porous media is a highly nonlinear multiphysical problem relevant to many engineering applications (e.g., the process of CO2 sequestration). Here, we extend and present a non-intrusive reduced order model of natural convection in porous media employing deep convolutional autoencoders for the compression and reconstruction and either radial basis function (RBF) interpolation or artificial neural networks (ANNs) for mapping parameters of partial differential equations (PDEs) on the corresponding nonlinear manifolds. To benchmark our approach, we also describe linear compression and reconstruction processes relying on proper orthogonal decomposition (POD) and ANNs. Further, we present comprehensive comparisons among different models through three benchmark problems. The reduced order models, linear and nonlinear approaches, are much faster than the finite element model, obtaining a maximum speed-up of 7 × 106 because our framework is not bound by the Courant–Friedrichs–Lewy condition; hence, it could deliver quantities of interest at any given time contrary to the finite element model. Our model’s accuracy still lies within a relative error of 7% in the worst-case scenario. We illustrate that, in specific settings, the nonlinear approach outperforms its linear counterpart and vice versa. We hypothesize that a visual comparison between principal component analysis (PCA) and t-Distributed Stochastic Neighbor Embedding (t-SNE) could indicate which method will perform better prior to employing any specific compression strategy.
This paper describes how the performance of motion primitive-based planning algorithms can be improved using reinforcement learning. Specifically, we describe and evaluate a framework that autonomously improves the performance of a primitive-based motion planner. The improvement process consists of three phases: exploration, extraction, and reward updates. This process can be iterated continuously to provide successive improvement. The exploration step generates new trajectories, and the extraction step identifies new primitives from these trajectories. These primitives are then used to update rewards for continued exploration. This framework required novel shaping rewards, development of a primitive extraction algorithm, and modification of the Hybrid A* algorithm. The framework is tested on a navigation task using a nonlinear F-16 model. The framework autonomously added 91 motion primitives to the primitive library and reduced average path cost by 21.6 s, or 35.75% of the original cost. The learned primitives are applied to an obstacle field navigation task, which was not used in training, and reduced path cost by 16.3 s, or 24.1%. Additionally, two heuristics for the modified Hybrid A* algorithm are designed to improve effective branching factor.
The Jet Propulsion Laboratory has a keen interest in exploring icy moons in the solar system, particularly Jupiter's Europa. Successful exploration of the moon's surface includes planetary protection initiatives to prevent the introduction of viable organisms from Earth to Europa. To that end, the Europa lander requires a Terminal Sterilization Subsystem (TSS) to rid the lander of viable organisms that would potentially contaminate the moon's environment. Sandia National Laboratories has been developing a TSS architecture, relying heavily on computational models to support TSS development. Sandia's TSS design approach involves using energetic material to thermally sterilize lander components at the end of the mission. A hierarchical modeling approach was used for system development and analysis, where simplified systems were constructed to perform empirical tests for evaluating energetic material formulation development and assist in developing computational models with multiple tiers of physics fidelity. Computational models have been developed using multiple Sandia-native computational tools. Three experimental systems and corresponding computational models have been developed: Tube, Sub-Box Small, and Sub-Box Large systems. This paper presents an explanation of the application context of the TSS along with an overview description of a small portion of the TSS development from a modeling and simulation perspective, specifically highlighting verification, validation, and uncertainty quantification (VVUQ) aspects of the modeling and simulation work. Multiple VVUQ approaches were implemented during TSS development, including solution verification, calibration, uncertainty quantification, global sensitivity analysis, and validation. This paper is not intended to express the design results or parameter values used to model the TSS but to communicate the approaches used and how the results of the VVUQ efforts were used and interpreted to assist system development.
We evaluate the use of reference modules for monitoring effective irradiance in PV power plants, as compared with traditional plane-of-array (POA) irradiance sensors, for PV monitoring and capacity tests. Common POA sensors such as pyranometers and reference cells are unable to capture module-level irradiance nonuniformity and require several correction factors to accurately represent the conditions for fielded modules. These problems are compounded for bifacial systems, where the power loss due to rear side shading and rear-side plane-of-array (RPOA) irradiance gradients are greater and more difficult to quantify. The resulting inaccuracy can have costly real-world consequences, particularly when the data are used to perform power ratings and capacity tests. Here we analyze data from a bifacial single-axis tracking PV power plant, (175.6 MWdc) using 5 meteorological (MET) stations, located on corresponding inverter blocks with capacities over 4 MWdc. Each MET station consists of bifacial reference modules as well pyranometers mounted in traditional POA and RPOA installations across the PV power plant. Short circuit current measurements of the reference modules are converted to effective irradiance with temperature correction and scaling based on flash test or nameplate short circuit values. Our work shows that bifacial effective irradiance measured by pyranometers averages 3.6% higher than the effective irradiance measured by bifacial reference modules, even when accounting for spectral, angle of incidence, and irradiance nonuniformity. We also performed capacity tests using effective irradiance measured by pyranometers and reference modules for each of the 5 bifacial single-axis tracking inverter blocks mentioned above. These capacity tests evaluated bifacial plant performance at ∼3.9% lower when using bifacial effective irradiance from pyranometers as compared to the same calculation performed with reference modules.
Carbon sequestration is a growing field that requires subsurface monitoring for potential leakage of the sequestered fluids through the casing annulus. Sandia National Laboratories (SNL) is developing a smart collar system for downhole fluid monitoring during carbon sequestration. This technology is part of a collaboration between SNL, University of Texas at Austin (UT Austin) (project lead), California Institute of Technology (Caltech), and Research Triangle Institute (RTI) to obtain real-time monitoring of the movement of fluids in the subsurface through direct formation measurements. Caltech and RTI are developing millimeter-scale radio frequency identification (RFID) sensors that can sense carbon dioxide, pH, and methane. These sensors will be impervious to cement, and as such, can be mixed with cement and poured into the casing annulus. The sensors are powered and communicate via standard RFID protocol at 902-928 MHz. SNL is developing a smart collar system that wirelessly gathers RFID sensor data from the sensors embedded in the cement annulus and relays that data to the surface via a wired pipe that utilizes inductive coupling at the collar to transfer data through each segment of pipe. This system cannot transfer a direct current signal to power the smart collar, and therefore, both power and communications will be implemented using alternating current and electromagnetic signals at different frequencies. The complete system will be evaluated at UT Austin's Devine Test Site, which is a highly characterized and hydraulically fractured site. This is the second year of the three-year effort, and a review of SNL's progress on the design and implementation of the smart collar system is provided.
This paper presents a visualization technique for incorporating eigenvector estimates with geospatial data to create inter-area mode shape maps. For each point of measurement, the method specifies the radius, color, and angular orientation of a circular map marker. These characteristics are determined by the elements of the right eigenvector corresponding to the mode of interest. The markers are then overlaid on a map of the system to create a physically intuitive visualization of the mode shape. This technique serves as a valuable tool for differentiating oscillatory modes that have similar frequencies but different shapes. This work was conducted within the Western Interconnection Modes Review Group (WIMRG) in the Western Electric Coordinating Council (WECC). For testing, we employ the WECC 2021 Heavy Summer base case, which features a high-fidelity, industry standard dynamic model of the North American Western Interconnection. Mode estimates are produced via eigen-decomposition of a reduced-order state matrix identified from simulated ringdown data. The results provide improved physical intuition about the spatial characteristics of the inter-area modes. In addition to offline applications, this visualization technique could also enhance situational awareness for system operators when paired with online mode shape estimates.
This study presents a method that can be used to gain information relevant to determining the corrosion risk for spent nuclear fuel (SNF) canisters during extended dry storage. Currently, it is known that stainless steel canisters are susceptible to chloride-induced stress corrosion cracking (CISCC). However, the rate of CISCC degradation and the likelihood that it could lead to a through-wall crack is unknown. This study uses well-developed computational fluid dynamics and particle-tracking tools and applies them to SNF storage to determine the rate of deposition on canisters. The deposition rate is determined for a vertical canister system and a horizontal canister system, at various decay heat rates with a uniform particle size distribution, ranging from 0.25 to 25 µm, used as an input. In all cases, most of the dust entering the overpack passed through without depositing. Most of what was retained in the overpack was deposited on overpack surfaces (e.g., inlet and outlet vents); only a small fraction was deposited on the canister itself. These results are provided for generalized canister systems with a generalized input; as such, this technical note is intended to demonstrate the technique. This study is a part of an ongoing effort funded by the U.S. Department of Energy, Nuclear Energy Office of Spent Fuel Waste Science and Technology, which is tasked with doing research relevant to developing a sound technical basis for ensuring the safe extended storage and subsequent transport of SNF. This work is being presented to demonstrate a potentially useful technique for SNF canister vendors, utilities, regulators, and stakeholders to utilize and further develop for their own designs and site-specific studies.
Integrating recent advancements in resilient algorithms and techniques into existing codes is a singular challenge in fault tolerance - in part due to the underlying complexity of implementing resilience in the first place, but also due to the difficulty introduced when integrating the functionality of a standalone new strategy with the preexisting resilience layers of an application. We propose that the answer is not to build integrated solutions for users, but runtimes designed to integrate into a larger comprehensive resilience system and thereby enable the necessary jump to multi-layered recovery. Our work designs, implements, and verifies one such comprehensive system of runtimes. Utilizing Fenix, a process resilience tool with integration into preexisting resilience systems as a design priority, we update Kokkos Resilience and the use pattern of VeloC to support application-level integration of resilience runtimes. Our work shows that designing integrable systems rather than integrated systems allows for user-designed optimization and upgrading of resilience techniques while maintaining the simplicity and performance of all-in-one resilience solutions. More application-specific choice in resilience strategies allows for better long-term flexibility, performance, and - importantly - simplicity.
Decarbonizing natural gas networks is a challenging enterprise. Replacing natural gas with renewable hydrogen is one option under global consideration to decarbonize heating, power and residential uses of natural gas. Hydrogen is known to degrade fatigue and fracture properties of structural steels, including pipeline steels. In this study, we describe environmental testing strategies aimed at generating baseline fatigue and fracture trends with efficient use of testing resources. For example, by controlling the stress intensity factor (K) in both K-increasing and K-decreasing modes, fatigue crack growth can be measured for multiple load ratios with a single specimen. Additionally, tests can be designed such that fracture tests can be performed at the conclusion of the fatigue crack growth test, further reducing the resources needed to evaluate the fracture mechanics parameters utilized in design. These testing strategies are employed to establish the fatigue crack growth behavior and fracture resistance of API grade steels in gaseous hydrogen environments. In particular, we explore the effects of load ratio and hydrogen partial pressure on the baseline fatigue and fracture trends of line pipe steels in gaseous hydrogen. These data are then used to test the applicability of a simple, universal fatigue crack growth model that accounts for both load ratio and hydrogen partial pressure. The appropriateness of this model for use as an upper bound fatigue crack growth is discussed.
This is an addendum to the Sierra/SolidMechanics 5.4 User’s Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State’s International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 5.4 User’s Guide should be referenced for most general descriptions of code capability and use.
We evaluate the use of reference modules for monitoring effective irradiance in PV power plants, as compared with traditional plane-of-array (POA) irradiance sensors, for PV monitoring and capacity tests. Common POA sensors such as pyranometers and reference cells are unable to capture module-level irradiance nonuniformity and require several correction factors to accurately represent the conditions for fielded modules. These problems are compounded for bifacial systems, where the power loss due to rear side shading and rear-side plane-of-array (RPOA) irradiance gradients are greater and more difficult to quantify. The resulting inaccuracy can have costly real-world consequences, particularly when the data are used to perform power ratings and capacity tests. Here we analyze data from a bifacial single-axis tracking PV power plant, (175.6 MWdc) using 5 meteorological (MET) stations, located on corresponding inverter blocks with capacities over 4 MWdc. Each MET station consists of bifacial reference modules as well pyranometers mounted in traditional POA and RPOA installations across the PV power plant. Short circuit current measurements of the reference modules are converted to effective irradiance with temperature correction and scaling based on flash test or nameplate short circuit values. Our work shows that bifacial effective irradiance measured by pyranometers averages 3.6% higher than the effective irradiance measured by bifacial reference modules, even when accounting for spectral, angle of incidence, and irradiance nonuniformity. We also performed capacity tests using effective irradiance measured by pyranometers and reference modules for each of the 5 bifacial single-axis tracking inverter blocks mentioned above. These capacity tests evaluated bifacial plant performance at ∼3.9% lower when using bifacial effective irradiance from pyranometers as compared to the same calculation performed with reference modules.
In transit visualization offers a desirable approach to performing in situ visualization by decoupling the simulation and visualization components. This decoupling requires that the data be transferred from the simulation to the visualization, which is typically done using some form of aggregation and redistribution. As the data distribution is adjusted to match the visualization’s parallelism during redistribution, the data transport layer must have knowledge of the input data structures to partition or merge them. In this chapter, we will discuss an alternative approach suitable for quickly integrating in transit visualization into simulations without incurring significant overhead or aggregation cost. Our approach adopts an abstract view of the input simulation data and works only on regions of space owned by the simulation ranks, which are sent to visualization clients on demand.
Structural alloys may experience corrosion when exposed to molten chloride salts due to selective dissolution of active alloying elements. One way to prevent this is to make the molten salt reducing. For the KCl + MgCl2 eutectic salt mixture, pure Mg can be added to achieve this. However, Mg can form intermetallic compounds with nickel at high temperatures, which may cause alloy embrittlement. This study shows that an optimum level of excess Mg could be added to the molten salt which will prevent corrosion of alloys like 316 H, while not forming any detectable Ni-Mg intermetallic phases on Ni-rich alloy surfaces.
Large scale non-intrusive inspection (NII) of commercial vehicles is being adopted in the U.S. at a pace and scale that will result in a commensurate growth in adjudication burdens at land ports of entry. The use of computer vision and machine learning models to augment human operator capabilities is critical in this sector to ensure the flow of commerce and to maintain efficient and reliable security operations. The development of models for this scale and speed requires novel approaches to object detection and novel adjudication pipelines. Here we propose a notional combination of existing object detection tools using a novel ensembling framework to demonstrate the potential for hierarchical and recursive operations. Further, we explore the combination of object detection with image similarity as an adjacent capability to provide post-hoc oversight to the detection framework. The experiments described herein, while notional and intended for illustrative purposes, demonstrate that the judicious combination of diverse algorithms can result in a resilient workflow for the NII environment.
Fires of practical interest are often large in scale and involve turbulent behavior. Fire simulation tools are often utilized in an under-resolved prediction to assess fire behavior. Data are scarce for large fires because they are difficult to instrument. A helium plume scenario has been used as a surrogate for much of the fire phenomenology (O'Hern et al., 2005), including buoyancy, mixing, and advection. A clean dataset of this nature makes an excellent platform for assessing model accuracy. We have been participating in a community effort to validate fire simulation tools, and the SIERRA/Fuego code is compared here with the historical dataset. Our predictions span a wide range of length-scales, and comparisons are made to species mass fraction and two velocity components for a number of heights in the core of the plume. We detail our approach to the comparisons, which involves some accommodation for the uncertainty in the inflow boundary condition from the test. We show evolving improvement in simulation accuracy with increasing mesh resolution and benchmark the accuracy through comparisons with the data.
The detonation of explosives produces luminous fireballs often containing particulates such as carbon soot or remnants of partially reacted explosives. The spatial distribution of these particulates is of great interest for the derivation and validation of models. In this work, three ultra-high-speed imaging techniques: diffuse back-illumination extinction, schlieren, and emission imaging, are utilized to investigate the particulate quantity, spatial distribution, and structure in a small-scale fireball. The measurements show the evolution of the particulate cloud in the fireball, identifying possible emission sources and regions of high optical thickness. Extinction measurements performed at two wavelengths shows that extinction follows the inverse wavelength behavior expected of absorptive particles in the Rayleigh scattering regime. The estimated mass from these extinction measurements shows an average soot yield consistent with previous soot collection experiments. The imaging diagnostics discussed in the current work can provide detailed information on the spatial distribution and concentration of soot, crucial for validation opportunities in the future.
This report describes recommended abuse testing procedures for rechargeable energy storage systems (RESSs) for electric vehicles. This report serves as a revision to the USABC Electrical Energy Storage System Abuse Test Manual for Electric and Hybrid Electric Vehicle Applications (SAND99-0497).
This user’s guide documents capabilities in Sierra/SolidMechanics which remain “in-development” and thus are not tested and hardened to the standards of capabilities listed in Sierra/SM 5.4 User’s Guide. Capabilities documented herein are available in Sierra/SM for experimental use only until their official release. These capabilities include, but are not limited to, novel discretization approaches such as the conforming reproducing kernel (CRK) method, numerical fracture and failure modeling aids such as the extended finite element method (XFEM) and J-integral, explicit time step control techniques, dynamic mesh rebalancing, as well as a variety of new material models and finite element formulations.
Creation of streaming video stimuli that allow for strict experimental control while providing ease of scene manipulation is difficult to achieve but desired by researchers seeking to approach ecological validity in contexts that involve processing streaming visual information. To that end, we propose leveraging video game modding tools as a method of creating research quality stimuli. As a pilot effort, we used a video game sandbox tool (Garry’s Mod) to create three steaming video scenarios designed to mimic video feeds that physical security personnel might observe. All scenarios required participants to identify the presences of a threat appearing during the video feed. Each scenario differed in level of complexity, in that one scenario required only location monitoring, one required location and action monitoring, and one required location, action, and conjunction monitoring in that when an action was performed it was only considered a threat when performed by a certain character model. While there was no behavioral effect of scenario in terms of accuracy or response times, in all scenarios we found evidence of a P300 when comparing response to threatening stimuli to that of standard stimuli. Results therefore indicate that sufficient levels of experimental control may be achieved to allow for the precise timing required for ERP analysis. Thus, we demonstrate the feasibility of using existing modding tools to create video scenarios amenable to neuroimaging analysis.
We have extended the computational singular perturbation (CSP) method to differential algebraic equation (DAE) systems and demonstrated its application in a heterogeneous-catalysis problem. The extended method obtains the CSP basis vectors for DAEs from a reduced Jacobian matrix that takes the algebraic constraints into account. We use a canonical problem in heterogeneous catalysis, the transient continuous stirred tank reactor (T-CSTR), for illustration. The T-CSTR problem is modelled fundamentally as an ordinary differential equation (ODE) system, but it can be transformed to a DAE system if one approximates typically fast surface processes using algebraic constraints for the surface species. We demonstrate the application of CSP analysis for both ODE and DAE constructions of a T-CSTR problem, illustrating the dynamical response of the system in each case. We also highlight the utility of the analysis in commenting on the quality of any particular DAE approximation built using the quasi-steady state approximation (QSSA), relative to the ODE reference case.
Simple but mission-critical internet-based applications that require extremely high reliability, availability, and verifiability (e.g., auditability) could benefit from running on robust public programmable blockchain platforms such as Ethereum. Unfortunately, program code running on such blockchains is normally publicly viewable, rendering these platforms unsuitable for applications requiring strict privacy of application code, data, and results. In this work, we investigate using MPC techniques to protect the privacy of a blockchain computation. While our main goal is to hide both the data and the computed function itself, we also consider the standard MPC setting where the function is public. We describe GABLE (Garbled Autonomous Bots Leveraging Ethereum), a blockchain MPC architecture and system. The GABLE architecture specifies the roles and capabilities of the players. GABLE includes two approaches for implementing MPC over blockchain: Garbled Circuits (GC), evaluating universal circuits, and Garbled Finite State Automata (GFSA). We formally model and prove the security of GABLE implemented over garbling schemes, a popular abstraction of GC and GFSA from (Bellare et al., CCS 2012). We analyze in detail the performance (including Ethereum gas costs) of both approaches and discuss the trade-offs. We implement a simple prototype of GABLE and report on the implementation issues and experience.
With the increase in penetration of inverter-based resources (IBRs) in the electrical power system, the ability of these devices to provide grid support to the system has become a necessity. With standards previously developed for the interconnection requirements of grid-following inverters (GFLI) (most commonly photovoltaic inverters), it has been well documented how these inverters 'should' respond to changes in voltage and frequency. However, with other IBRs such as grid-forming inverters (GFMIs) (used for energy storage systems, standalone systems, and as uninterruptable power supplies) these requirements are either: not yet documented, or require a more in deep analysis. With the increased interest in microgrids, GFMIs that can be paralleled onto a distribution system have become desired. With the proper control schemes, a GFMI can help maintain grid stability through fast response compared to rotating machines. This paper will present an experimental comparison of commercially available GFMIand GFLI ' responses to voltage and frequency deviation, as well as the GFMIoperating as a standalone system and subjected to various changes in loads.
We examine coupling into azimuthal slots on an infinite cylinder with a infinite length interior cavity operating both at the fundamental cavity modal frequencies, with small slots and a resonant slot, as well as higher frequencies. The coupling model considers both radiation on an infinite cylindrical exterior as well as a half space approximation. Bounding calculations based on maximum slot power reception and interior power balance are also discussed in detail and compared with the prior calculations. For higher frequencies limitations on matching are imposed by restricting the loads ability to shift the slot operation to the nearest slot resonance; this is done in combination with maximizing the power reception as a function of angle of incidence. Finally, slot power mismatch based on limited cavity load quality factor is considered below the first slot resonance.
This paper presents a run-to-run (R2R) controller for mechanical serial sectioning (MSS). MSS is a destructive material analysis process which repeatedly removes a thin layer of material and images the exposed surface. The images are then used to gain insight into the material properties and often to construct a 3-dimensional reconstruction of the material sample. Currently, an experience human operator selects the parameters of the MSS to achieve the desired thickness. The proposed R2R controller will automate this process while improving the precision of the material removal. The proposed R2R controller solves an optimization problem designed to minimize the variance of the material removal subject to achieving the expected target removal. This optimization problem was embedded in an R2R framework to provide iterative feedback for disturbance rejection and convergence to the target removal amount. Since an analytic model of the MSS system is unavailable, we adopted a data-driven approach to synthesize our R2R controller from historical data. The proposed R2R controller is demonstrated through simulations. Future work will empirically demonstrate the proposed R2R through experiments with a real MSS system.
Stochasticity is ubiquitous in the world around us. However, our predominant computing paradigm is deterministic. Random number generation (RNG) can be a computationally inefficient operation in this system especially for larger workloads. Our work leverages the underlying physics of emerging devices to develop probabilistic neural circuits for RNGs from a given distribution. However, codesign for novel circuits and systems that leverage inherent device stochasticity is a hard problem. This is mostly due to the large design space and complexity of doing so. It requires concurrent input from multiple areas in the design stack from algorithms, architectures, circuits, to devices. In this paper, we present examples of optimal circuits developed leveraging AI-enhanced codesign techniques using constraints from emerging devices and algorithms. Our AI-enhanced codesign approach accelerated design and enabled interactions between experts from different areas of the micro-electronics design stack including theory, algorithms, circuits, and devices. We demonstrate optimal probabilistic neural circuits using magnetic tunnel junction and tunnel diode devices that generate an RNG from a given distribution.
Zhang, Chen; Jacobson, Clas; Zhang, Qi; Biegler, Lorenz T.; Eslick, John C.; Zamarripa, Miguel A.; Stinchfeld, Georgia; Siirola, John D.; Laird, Carl D.
For many industries addressing varied customer needs means producing a family of products that satisfy a range of design requirements. Manufacturers seek to design this family of products while exploiting opportunities for shared components to reduce manufacturing cost and complexity. We present a mixed-integer programming formulation that determines the optimal design for each product, the number and design of shared components, and the allocation of those shared components across the products in the family. This formulation and workflow for product family design has created significant business impact on the industrial design of product families for large-scale commercial HVAC chillers in Carrier Global Corporation. We demonstrate the approach on an open case study based on a transcritical CO2 refrigeration cycle. This case study and our industrial experience show that the formulation is computationally tractable and can significantly reduce engineering time by replacing the manual design process with an automated approach.
In accident scenarios involving release of tritium during handling and storage, the level of risk to human health is dominated by the extent to which radioactive tritium is oxidized to the water form (T2O or THO). At some facilities, tritium inventories consist of very small quantities stored at sub-atmospheric pressure, which means that tritium release accident scenarios will likely produce concentrations in air that are well below the lower flammability limit. It is known that isotope effects on reaction rates should result in slower oxidation rates for heavier isotopes of hydrogen, but this effect has not previously been quantified for oxidation at concentrations well below the lower flammability limit for hydrogen. This work describes hydrogen isotope oxidation measurements in an atmospheric tube furnace reactor. These measurements consist of five concentration levels between 0.01% and 1% protium or deuterium and two residence times. Oxidation is observed to occur between about 550°C and 800°C, with higher levels of conversion achieved at lower temperatures for protium with respect to deuterium at the same volumetric inlet concentration and residence time. Computational fluid dynamics simulations of the experiments were used to customize reaction orders and Arrhenius parameters in a 1-step oxidation mechanism. The trends in the rates for protium and deuterium are extrapolated based on guidance from literature to produce kinetic rate parameters appropriate for tritium oxidation at low concentrations.
In high temperature (HT) environments often encountered in geothermal wells, data rate transfers for downhole instrumentation are relatively limited due to transmission line bandwidth and insertion loss and the processing speed of HT microcontrollers. In previous research, Sandia National Laboratory Geothermal Department obtained 3.8 Mbps data rates over 1524 m (5000 ft) for single conductor wireline cable with less than a 1x10-8 bit error rate utilizing low temperature NITM hardware (formerly National InstrumentsTM). Our protocol technique was a combination of orthogonal frequency-division multiplexing and quadrature amplitude modulation across the bandwidth of the single conductor wireline. This showed it is possible to obtain high data rates in low bandwidth wirelines. This paper focuses on commercial HT microcontrollers (µC), rather than low temperature NITM modules, to enable high-speed communication in an HT environment. As part of this effort, four devices were evaluated, and an optimal device (SM320F28335-HT) was selected for its high clock rates, floating-point unit, and on-board analog-to-digital converter. A printed circuit board was assembled with the HT µC, an HT resistor digital-to-analog converter, and an HT line driver. The board was tested at the microcontroller's rated maximum temperature (210°C) for a week while transmitting through a 1524 m (5000 ft) wireline. A final test was conducted to the point of failure at elevated temperatures. This paper will discuss communication methods, achieved data rates, and hardware selection. This effort contributes to the enhancement of HT instrumentation by enabling greater sensor counts and improving data accuracy and transfer rates.
Ship emissions can form linear cloud structures, or ship tracks, when atmospheric water vapor condenses on aerosols in the ship exhaust. These structures are of interest because they are observable and traceable examples of MCB, a mechanism that has been studied as a potential approach for solar climate intervention. Ship tracks can be observed throughout the diurnal cycle via space-borne assets like the advanced baseline imagers on the national oceanic and atmospheric administration geostationary operational environmental satellites, the GOES-R series. Due to complex atmospheric dynamics, it can be difficult to track these aerosol perturbations over space and time to precisely characterize how long a single emission source can significantly contribute to indirect radiative forcing. We propose an optical flow approach to estimate the trajectories of ship-emitted aerosols after they begin mixing with low boundary layer clouds using GOES-17 satellite imagery. Most optical flow estimation methods have only been used to estimate large scale atmospheric motion. We demonstrate the ability of our approach to precisely isolate the movement of ship tracks in low-lying clouds from the movement of large swaths of high clouds that often dominate the scene. This efficient approach shows that ship tracks persist as visible, linear features beyond 9 h and sometimes longer than 24 h.
We propose a two-stage scenario-based stochastic optimization problem to determine investments that enhance power system resilience. The proposed optimization problem minimizes the Conditional Value at Risk (CVaR) of load loss to target low-probability high-impact events. We provide results in the context of generator winterization investments in Texas using winter storm scenarios generated from historical data collected from Winter Storm Uri. Results illustrate how the CVaR metric can be used to minimize the tail of the distribution of load loss and illustrate how risk-Aversity impacts investment decisions.
Proceedings of the Nuclear Criticality Safety Division Topical Meeting, NCSD 2022 - Embedded with the 2022 ANS Annual Meeting
Salazar, Alex
The postclosure criticality safety assessment for the direct disposal of dual-purpose canisters (DPCs) in a geologic repository includes considerations of transient criticality phenomena. The power pulse from a hypothetical transient criticality event in an unsaturated alluvial repository is evaluated for a DPC containing 37 spent pressurized water reactor (PWR) assemblies. The scenario assumes that the conditions for baseline criticality are achieved through flooding with groundwater and progressive failure of neutron absorbing media. A preliminary series of steady-state criticality calculations is conducted to characterize reactivity feedback due to absorber degradation, Doppler broadening, and thermal expansion. These feedback coefficients are used in an analysis with a reactor kinetics code to characterize the transient pulse given a positive reactivity insertion for a given length of time. The time-integrated behavior of the pulse can be used to model effects on the DPC and surrounding barriers in future studies and determine if transient criticality effects are consequential.
The precise estimation of performance loss rate (PLR) of photovoltaic (PV) systems is vital for reducing investment risks and increasing the bankability of the technology. Until recently, the PLR of fielded PV systems was mainly estimated through the extraction of a linear trend from a time series of performance indicators. However, operating PV systems exhibit failures and performance losses that cause variability in the performance and may bias the PLR results obtained from linear trend techniques. Change-point (CP) methods were thus introduced to identify nonlinear trend changes and behaviour. The aim of this work is to perform a comparative analysis among different CP techniques for estimating the annual PLR of eleven grid-connected PV systems installed in Cyprus. Outdoor field measurements over an 8-year period (June 2006-June 2014) were used for the analysis. The obtained results when applying different CP algorithms to the performance ratio time series (aggregated into monthly blocks) demonstrated that the extracted trend may not always be linear but sometimes can exhibit nonlinearities. The application of different CP methods resulted to PLR values that differ by up to 0.85% per year (for the same number of CPs/segments).
We present a procedure for randomly generating realistic steady-state contingency scenarios based on the historical outage data from a particular event. First, we divide generation into classes and fit a probability distribution of outage magnitude for each class. Second, we provide a method for randomly synthesizing generator resilience levels in a way that preserves the data-driven probability distributions of outage magnitude. Finally, we devise a simple method of scaling the storm effects based on a single global parameter. We apply our methods using data from historical Winter Storm Uri to simulate contingency events for the ACTIVSg2000 synthetic grid on the footprint of Texas.
The penetration of renewable energy resources (RER) and energy storage systems (ESS) into the power grid has been accelerated in recent times due to the aggressive emission and RER penetration targets. The Integrated resource planning (IRP) framework can help in ensuring long-term resource adequacy while satisfying RER integration and emission reduction targets in a cost-effective and reliable manner. In this paper, we present pIRP (probabilistic Integrated Resource Planning), an open-source Python-based software tool designed for optimal portfolio planning for an RER and ESS rich future grid and for addressing the capacity expansion problem. The tool, which is planned to be released publicly, with its ESS and RER modeling capabilities along with enhanced uncertainty handling make it one of the more advanced non-commercial IRP tools available currently. Additionally, the tool is equipped with an intuitive graphical user interface and expansive plotting capabilities. Impacts of uncertainties in the system are captured using Monte Carlo simulations and lets the users analyze hundreds of scenarios with detailed scenario reports. A linear programming based architecture is adopted which ensures sufficiently fast solution time while considering hundreds of scenarios and characterizing profile risks with varying levels of RER and ESS penetration levels. Results for a test case using data from parts of the Eastern Interconnection are provided in this paper to demonstrate the capabilities offered by the tool.
This paper presents the formulation, implementation, and demonstration of a new, largely phenomenological, model for the damage-free (micro-crack-free) thermomechanical behavior of rock salt. Unlike most salt constitutive models, the new model includes both drag stress (isotropic) and back stress (kinematic) hardening. The implementation utilizes a semi-implicit scheme and a fall-back fully-implicit scheme to numerically integrate the model's differential equations. Particular attention was paid to the initial guesses for the fully-implicit scheme. Of the four guesses investigated, an initial guess that interpolated between the previous converged state and the fully saturated hardening state had the best performance. The numerical implementation was then used in simulations that highlighted the difference between drag stress hardening versus combined drag and back stress hardening. Simulations of multi-stage constant stress tests showed that only combined hardening could qualitatively represent reverse (inverse transient) creep, as well as the large transient strains experimentally observed upon switching from axisymmetric compression to axisymmetric extension. Simulations of a gas storage cavern subjected to high and low gas pressure cycles showed that combined hardening led to substantially greater volume loss over time than drag stress hardening alone.
Metasurface lenses are fabricated using membrane projection lithography following a CMOS-compatible process flow. The lenses are 10-mm in diameter and employ 3-dimensional unit cells designed to function in the mid-infrared spectral range.
Dynamical systems subject to intermittent contact are often modeled with piecewise-smooth contact forces. However, the discontinuous nature of the contact can cause inaccuracies in numerical results or failure in numerical solvers. Representing the piecewise contact force with a continuous and smooth function can mitigate these problems, but not all continuous representations may be appropriate for this use. In this work, five representations used by previous researchers (polynomial, rational polynomial, hyperbolic tangent, arctangent, and logarithm-arctangent functions) are studied to determine which ones most accurately capture nonlinear behaviors including super- and subharmonic resonances, multiple solutions, and chaos. The test case is a single-DOF forced Duffing oscillator with freeplay nonlinearity, solved using direct time integration. This work intends to expand on past studies by determining the limits of applicability for each representation and what numerical problems may occur.
Proceedings of SPIE - The International Society for Optical Engineering
Fredricksen, C.J.; Peale, R.E.; Dhakal, N.; Barrett, C.L.; Boykin II, O.; Maukonen, D.; Davis, L.; Ferarri, B.; Chernyak, L.; Zeidan, O.A.; Hawkins, Samuel D.; Klem, John F.; Krishna, Sanjay; Kazemi, Alireza; Schuler-Sandy, Ted
Effects of gamma and proton irradiation, and of forward bias minority carrier injection, on minority carrier diffusion and photoresponse were investigated for long-wave (LW) and mid-wave (MW) infrared detectors with engineered majoritycarrier barriers. The LWIR detector was a type-II GaSb/InAs strained-layer superlattice pBiBn structure. The MWIR detector was a InAsSb/AlAsSb nBp structure without superlattices. Room temperature gamma irradiations degraded the minority carrier diffusion length of the LWIR structure, and minority carrier injections caused dramatic improvements, though there was little effect from either treatment on photoresponse. For the MWIR detector, effects of room temperature gamma irradiation and injection on minority carrier diffusion and photoresponse were negligible. Subsequently, both types of detectors were subjected to gamma irradiation at 77 K. In-situ photoresponse was unchanged for the LWIR detectors, while that for the MWIR ones decreased 19% after cumulative dose of ~500 krad(Si). Minority carrier injection had no effect on photoresponse for either. The LWIR detector was then subjected to 4 Mrad(Si) of 30 MeV proton irradiation at 77 K, and showed a 35% decrease in photoresponse, but again no effect from forward bias injection. These results suggest that photoresponse of the LWIR detectors is not limited by minority carrier diffusion.
We propose the use of balanced iterative reducing and clustering using hierarchies (BIRCH) combined with linear regression to predict the reduced Young's modulus and hardness of highly heterogeneous materials from a set of nanoindentation experiments. We first use BIRCH to cluster the dataset according to its mineral compositions, which are derived from the spectral matching of energy-dispersive spectroscopy data through the modular automated processing system (MAPS) platform. We observe that grouping our dataset into five clusters yields the best accuracy as well as a reasonable representation of mineralogy in each cluster. Subsequently, we test four types of regression models, namely linear regression, support vector regression, Gaussian process regression, and extreme gradient boosting regression. The linear regression and Gaussian process regression provide the most accurate prediction, and the proposed framework yields R2 = 0.93 for the test set. Although the study is needed more comprehensively, our results shows that machine learning methods such as linear regression or Gaussian process regression can be used to accurately estimate mechanical properties with a proper number of grouping based on compositional data.
It is impossible in practice to comprehensively test even small software programs due to the vastness of the reachable state space; however, modern cyber-physical systems such as aircraft require a high degree of confidence in software safety and reliability. Here we explore methods of generating test sets to effectively and efficiently explore the state space for a module based on the Traffic Collision Avoidance System (TCAS) used on commercial aircraft. A formal model of TCAS in the model-checking language NuSMV provides an output oracle. We compare test sets generated using various methods, including covering arrays, random, and a low-complexity input paradigm applied to 28 versions of the TCAS C program containing seeded errors. Faults are triggered by tests for all 28 programs using a combination of covering arrays and random input generation. Complexity-based inputs perform more efficiently than covering arrays, and can be paired with random input generation to create efficient and effective test sets. A random forest classifier identifies variable values that can be targeted to generate tests even more efficiently in future work, by combining a machine-learned fuzzing algorithm with more complex model oracles developed in model-based systems engineering (MBSE) software.
An array of Wave Energy Converters (WEC) is required to supply a significant power level to the grid. However, the control and optimization of such an array is still an open research question. This paper analyzes two aspects that have a significant impact on the power production. First the spacing of the buoys in a WEC array will be analyzed to determine the optimal shift between the buoys in an array. Then the wave force interacting with the buoys will be angled to create additional sequencing between the electrical signals. A cost function is proposed to minimize the power variation and energy storage while maximizing the delivered energy to the onshore point of common coupling to the electrical grid.
Refractory complex concentrated alloys are an emerging class of materials that attracts attention due to their stability and performance at high temperatures. In this study, we investigate the variations in the mechanical and thermal properties across a broad compositional space for the refractory MoNbTaTi quaternary using high-throughput ab-initio calculations and experimental characterization. For all the properties surveyed, we note a good agreement between our modeling predictions and the experimentally measured values. We reveal the particular role of molybdenum (Mo) to achieve high strength when in high concentration. We trace the origin of this phenomenon to a shift from metallic to covalent bonding when the Mo content is increased. Additionally, a mechanistic, dislocation-based description of the yield strength further explains such high strength due to a combination of high bulk and shear moduli, accompanied by the relatively small size of the Mo atom compared to the other atoms in the alloy. Our analysis of the thermodynamics properties shows that regardless of the composition, this class of quaternary alloys shows good stability and low sensitivity to temperature. Taken together, these results pave the way for the design of new high-performance refractory alloys beyond the equimolar composition found in high-entropy alloys.
This work explores deriving transmissibility functions for a missile from a measured location at the base of the fairing to a desired location within the payload. A pressure on the outside of the fairing and the rocket motor’s excitation creates an acceleration at a measured location and a desired location. Typically, the desired location is not measured. In fact, it is typical that the payload may change, but measured acceleration at the base of the fairing is generally similar to previous test flights. Given this knowledge, it is desired to use a finite-element model to create a transmissibility function which relates acceleration from the previous test flight’s measured location at the base of the fairing to acceleration at a location in the new payload. Four methods are explored for deriving this transmissibility, with the goal of finding an appropriate transmissibility when both the pressure and rocket motor excitation are equally present. These methods are assessed using transient results from a simple example problem, and it is found that one of the methods gives good agreement with the transient results for the full range of loads considered.
Applications such as counterfeit identification, quality control, and non-destructive material identification benefit from improved spatial and compositional analysis. X-ray Computed Tomography is used in these applications but is limited by the X-ray focal spot size and the lack of energy-resolved data. Recently developed hyperspectral X-ray detectors estimate photon energy, which enables composition analysis but lacks spatial resolution. Moving beyond bulk homogeneous transmission anodes toward multi-metal patterned anodes enables improvements in spatial resolution and signal-to-noise ratios in these hyperspectral X-ray imaging systems. We aim to design and fabricate transmission anodes that facilitate confirmation of previous simulation results. These anodes are fabricated on diamond substrates with conventional photolithography and metal deposition processes. The final transmission anode design consists of a cluster of three disjoint metal bumps selected from molybdenum, silver, samarium, tungsten, and gold. These metals are chosen for their k-lines, which are positioned within distinct energy intervals of interest and are readily available in standard clean rooms. The diamond substrate is chosen for its high thermal conductivity and high transmittance of X-rays. The feature size of the metal bumps is chosen such that the cluster is smaller than the 100 m diameter of the impinging electron beam in the X-ray tube. This effectively shrinks the X-ray focal spot in the selected energy bands. Once fabricated, our transmission anode is packaged in a stainless-steel holder that can be retrofitted into our existing X-ray tube. Innovations in anode design enable an inexpensive and simple method to improve existing X-ray imaging systems.
Frequent changes in penetration levels of distributed energy resources (DERs) and grid control objectives have caused the maintenance of accurate and reliable grid models for behind-the-meter (BTM) photovoltaic (PV) system impact studies to become an increasingly challenging task. At the same time, high adoption rates of advanced metering infrastructure (AMI) devices have improved load modeling techniques and have enabled the application of machine learning algorithms to a wide variety of model calibration tasks. Therefore, we propose that these algorithms can be applied to improve the quality of the input data and grid models used for PV impact studies. In this paper, these potential improvements were assessed for their ability to improve the accuracy of locational BTM PV hosting capacity analysis (HCA). Specifically, the voltage- and thermal-constrained hosting capacities of every customer location on a distribution feeder (1,379 in total) were calculated every 15 minutes for an entire year before and after each calibration algorithm or load modeling technique was applied. Overall, the HCA results were found to be highly sensitive to the various modeling deficiencies under investigation, illustrating the opportunity for more data-centric/model-free approaches to PV impact studies.
Transportation of sodium-bonded spent fuel appears to present no unique challenges. Storage systems for this fuel should be designed to keep water, both liquid and vapor, from contacting the spent fuel. This fuel is not suitable for geologic disposal; therefore, how the spent sodium bonded fuel will be processed and the characteristics of the final disposal waste form(s) need to be considered. TRISO spent fuel appears to present no unique challenges in terms of transportation, storage, or disposal. If the graphite block is disposed of with the TRISO spent fuel, the 14C and 3H generated would need to be considered in the postclosure performance assessment. Salt waste from the molten salt reactor has yet to be transported or stored and might be a challenge to dispose of in a non-salt repositories. Like sodium-bonded spent fuel, how the salt will be treated and the characteristics of the final disposal waste form(s) need to be considered. In addition, radiolysis in the frozen salt waste form continues to generate gas, which presents a hazard. Both HALEU and high-enriched uranium SNF are currently being stored and transported by the DOE. Disposal of fuels with enrichments greater than 5% was included in the disposal plan for Yucca Mountain. The increased potential for criticality associated with the higher enriched SNF is mitigated by additional criticality control measures. Fuels that are similar to some ATFs were part of the disposal plan for Yucca Mountain. Some of the properties of these fuels (swelling, generation of 14C) would have to be considered as part of a postclosure performance assessment.
The goal of this paper is to present a set of measurements from a benchmark structure containing two bolted joints to support future efforts to predict the damping due to the joints and to model nonlinear coupling between the first two elastic modes. Bolted joints introduce nonlinearities in structures, typically causing a softening in the natural frequency and an increase in damping because of frictional slip between the contact interfaces within the joint. These nonlinearities pose significant challenges when characterizing the response of the structure under a large range of load amplitudes, especially when the modal responses become coupled, causing the effective damping and natural frequency to not only depend on the excitation amplitude of the targeted mode, but also the relative amplitudes of other modes. In this work, two nominally identical benchmark structures, known in some prior works as the S4 beam, are tested to characterize their nonlinear properties for the first two elastic modes. Detailed surface measurements are presented and validated through finite element analysis and reveal distinct contact interactions between the two sets of beams. The free-free test structures are excited with an impact hammer and the transient response is analyzed to extract the damping and frequency backbone curves. A range of impact amplitudes and drive points are used to isolate a single mode or to excite both modes simultaneously. Differences in the nonlinear response correlate with the relative strength of the modes that are excited, allowing one to characterize mode coupling. Each of the beams shows different nonlinear properties for each mode, which is attributed to the different contact pressure distributions between the parts, although the mode coupling relationship is found to be consistent between the two. The test data key finding are presented in this paper and the supporting data is available on a public repository for interested researchers.
Many teams struggle to adapt and right-size software engineering best practices for quality assurance to fit their context. Introducing software quality is not usually framed in a way that motivates teams to take action, thus resulting in it becoming a "check the box for compliance"activity instead of a cultural practice that values software quality and the effort to achieve it. When and how can we provide effective incentives for software teams to adopt and integrate meaningful and enduring software quality practices? We explored this question through a persona-based ideation exercise at the 2021 Collegeville Workshop on Scientific Software in which we created three unique personas that represent different scientific software developer perspectives.
The focus of this study is on spectral equivalence results for higher-order tensor product finite elements in the H(curl), H(div), and L2 function spaces. For certain choices of the higher-order shape functions, the resulting mass and stiffness matrices are spectrally equivalent to those for an assembly of lowest-order edge-, face- or interior-based elements on the associated Gauss–Lobatto–Legendre (GLL) mesh.
The growing x-ray detection burden for vehicles at Ports of Entry in the US requires the development of efficient and reliable algorithms to assist human operator in detecting contraband. Developing algorithms for large-scale non-intrusive inspection (NII) that both meet operational performance requirements and are extensible for use in an evolving environment requires large volumes and varieties of training data, yet collecting and labeling data for these enivornments is prohibitively costly and time consuming. Given these, generating synthetic data to augment algorithm training has been a focus of recent research. Here we discuss the use of synthetic imagery in an object detection framework, and describe a simulation based approach to determining domain-informed threat image projection (TIP) augmentation.
Geothermal energy has been underutilized in the U.S., primarily due to the high cost of drilling in the harsh environments encountered during the development of geothermal resources. Drilling depths can approach 5,000 m with temperatures reaching 170 C. In situ geothermal fluids are up to ten times more saline than seawater and highly corrosive, and hard rock formations often exceed 240 MPa compressive strength. This combination of extreme conditions pushes the limits of most conventional drilling equipment. Furthermore, enhanced geothermal systems are expected to reach depths of 10,000 m and temperatures more than 300 °C. To address these drilling challenges, Sandia developed a proof-of-concept tool called the auto indexer under an annual operating plan task funded by the Geothermal Technologies Program (GTP) of the U.S. Department of Energy Geothermal Technologies Office. The auto indexer is a relatively simple, elastomer-free motor that was shown previously to be compatible with pneumatic hammers in bench-top testing. Pneumatic hammers can improve penetration rates and potentially reduce drilling costs when deployed in appropriate conditions. The current effort, also funded by DOE GTP, increased the technology readiness level of the auto indexer, producing a scaled prototype for drilling larger diameter boreholes using pneumatic hammers. The results presented herein include design details, modeling and simulation results, and testing results, as well as background on percussive hammers and downhole rotation.
Given a graph, finding the distance-2 maximal independent set (MIS-2) of the vertices is a problem that is useful in several contexts such as algebraic multigrid coarsening or multilevel graph partitioning. Such multilevel methods rely on finding the independent vertices so they can be used as seeds for aggregation in a multilevel scheme. We present a parallel MIS-2 algorithm to improve performance on modern accelerator hardware. This algorithm is implemented using the Kokkos programming model to enable performance portability. We demonstrate the portability of the algorithm and the performance on a variety of architectures (x86/ARM CPUs and NVIDIA/AMD GPUs). The resulting algorithm is also deterministic, producing an identical result for a given input across all of these platforms. The new MIS-2 implementation outperforms implementations in state of the art libraries like CUSP and ViennaCL by 3-8x while producing similar quality results. We further demonstrate the benefits of this approach by developing parallel graph coarsening scheme for two different use cases. First, we develop an algebraic multigrid (AMG) aggregation scheme using parallel MIS-2 and demonstrate the benefits as opposed to previous approaches used in the MueLu multigrid package in Trilinos. We also describe an approach for implementing a parallel multicolor 'cluster' Gauss-Seidel preconditioner using this MIS-2 coarsening, and demonstrate better performance with an efficient, parallel, mul-ticolor Gauss-Seidel algorithm.
Rock salt is being considered as a medium for energy storage and radioactive waste disposal. A Disturbed Rock Zone (DRZ) develops in the immediate vicinity of excavations in rock salt, with an increase in permeability, which alters the migration of gases and liquids around the excavation. When creep occurs adjacent to a stiff inclusion such as a concrete plug, it is expected that the stress state near the inclusion will become more hydrostatic and less deviatoric, promoting healing (permeability reduction) of the DRZ. In this scoping study, we measured the permeability of DRZ rock salt with time adjacent to inclusions (plugs) of varying stiffness to determine how the healing of rock salt, as reflected in the permeability changes, is a function of the stress and time. Samples were created with three different inclusion materials in a central hole along the axis of a salt core: (i) very soft silicone sealant, (ii) sorel cement, and (iii) carbon steel. The measured permeabilities are corrected for the gas slippage effect. We observed that the permeability change is a function of the inclusion material. The stiffer the inclusion, the more rapidly the permeability reduces with time.
Any program tasked with the evaluation and acquisition of algorithms for use in deployed scenarios must have an impartial, repeatable, and auditable means of benchmarking both candidate and fielded algorithms. Success in this endeavor requires a body of representative sensor data, data labels indicating the proper algorithmic response to the data as adjudicated by subject matter experts, a means of executing algorithms under review against the data, and the ability to automatically score and report algorithm performance. Each of these capabilities should be constructed in support of program and mission goals. By curating and maintaining data, labels, tests, and scoring methodology, a program can understand and continually improve the relationship between benchmarked and fielded performance of acquired algorithms. A system supporting these program needs, deployed in an environment with sufficient computational power and necessary security controls is a powerful tool for ensuring due diligence in evaluation and acquisition of mission critical algorithms. This paper describes the Seascape system and its place in such a process.
Density fluctuations in compressible turbulent boundary layers cause aero-optical distortions that affect the performance of optical systems such as sensors and lasers. The development of models for predicting the aero-optical distortions relies on theory and reference data that can be obtained from experiments and time-resolved simulations. This paper reports on wall-modeled large-eddy simulations of turbulent boundary layers over a flat plate at Mach 3.5, 7.87, and 13.64. The conditions for the Mach 3.5 case match those for the DNS presented by Miller et al.1 The Mach 7.87 simulation match those inside the Hypersonic Wind Tunnel at Sandia National Laboratories. For the Mach 13.64, the conditions inside the Arnold Engineering Development Complex Hypervelocity Tunnel 9 are matched. Overall, adequate agreement of the velocity and temperature as well as Reynolds stress profiles with reference data from direct numerical simulations is obtained for the different Mach numbers. For all three cases, the normalized root-mean-square optical path difference was computed and compared with data obtained from the reference direct numerical simulations and experiments, as well as predictions obtained with a semi-analytical relationship by Notre Dame University. Above Mach five, the normalized path difference obtained from the simulations is above the model prediction. This provides motivation for future work aimed at evaluating the assumptions behind the Notre Dame model for hypersonic boundary layer flows.
This paper demonstrates that a faster Automatic Generation Control (AGC) response provided by Inverter-Based Resources (IBRs) can improve a performance-based regulation (PBR) metric. The improvement in performance has a direct effect on operational income. The PBR metric used in this work was obtained from a California ISO (CAISO) example and is fully described herein. A single generator in a modified three area IEEE 39 bus system was replaced with a group of co-located IBRs to present possible responses using different plant controls and variable resource conditions. We show how a group of IBRs that rely on variable resources may negatively affect the described PBR metric of all connected areas if adequate plant control is not employed. However, increasing the dispatch rate of internal plant controls may positively affect the PBR metric of all connected areas despite variable resource conditions.
To keep pace with the demand for innovation through scientific computing, modern scientific software development is increasingly reliant upon a rich and diverse ecosystem of software libraries and toolchains. Research software engineers (RSEs) responsible for that infrastructure perform highly integrative work, acting as a bridge between the hardware, the needs of researchers, and the software layers situated between them; relatively little, however, has been written about the role played by RSEs in that work and what support they need to thrive. To that end, we present a two-part report on the development of half-precision floating point support in the Kokkos Ecosystem. Half-precision computation is a promising strategy for increasing performance in numerical computing and is particularly attractive for emerging application areas (e.g., machine learning), but developing practicable, portable, and user-friendly abstractions is a nontrivial task. In the first half of the paper, we conduct an engineering study on the technical implementation of the Kokkos half-precision scalar feature and showcase experimental results; in the second half, we offer an experience report on the challenges and lessons learned during feature development by the first author. We hope our study provides a holistic view on scientific library development and surfaces opportunities for future studies into effective strategies for RSEs engaged in such work.
Hu, Xuan; Walker, Benjamin W.; Garcia-Sanchez, Felipe; Edwards, Alexander J.; Zhou, Peng; Incorvia, Jean A.C.; Paler, Alexandru; Frank, Michael P.; Friedman, Joseph S.
Magnetic skyrmions are nanoscale whirls of magnetism that can be propagated with electrical currents. The repulsion between skyrmions inspires their use for reversible computing based on the elastic billiard ball collisions proposed for conservative logic in 1982. In this letter, we evaluate the logical and physical reversibility of this skyrmion logic paradigm, as well as the limitations that must be addressed before dissipation-free computation can be realized.
Femtosecond laser electronic excitation tagging (FLEET) is a powerful unseeded velocimetry technique typically used to measure one component of velocity along a line, or two or three components from a dot. In this Letter, we demonstrate a dotted-line FLEET technique which combines the dense profile capability of a line with the ability to perform two-component velocimetry with a single camera on a dot. Our set-up uses a single beam path to create multiple simultaneous spots, more than previously achieved in other FLEET spot configurations. We perform dotted-line FLEET measurements downstream of a highly turbulent, supersonic nitrogen free jet. Dotted-line FLEET is created by focusing light transmitted by a periodic mask with rectangular slits of 1.6 × 40 mm2 and an edge-to-edge spacing of 0.5 mm, then focusing the imaged light at the measurement region. Up to seven symmetric dots spaced approximately 0.9 mm apart, with mean full-width at half maximum diameters between 150 and 350 µm, are simultaneously imaged. Both streamwise and radial velocities are computed and presented in this Letter.
Conference Proceedings of the Society for Experimental Mechanics Series
Singh, Aabhas; Wielgus, Kayla M.; Dimino, Ignazio; Kuether, Robert J.; Allen, Matthew S.
Morphing wings have great potential to dramatically improve the efficiency of future generations of aircraft and to reduce noise and emissions. Among many camber morphing wing concepts, shape changing fingerlike mechanisms consist of components, such as torsion bars, bushings, bearings, and joints, all of which exhibit damping and stiffness nonlinearities that are dependent on excitation amplitude. These nonlinearities make the dynamic response difficult to model accurately with traditional simulation approaches. As a result, at high excitation levels, linear finite element models may be inaccurate, and a nonlinear modeling approach is required to capture the necessary physics. This work seeks to better understand the influence of nonlinearity on the effective damping and natural frequency of the morphing wing through the use of quasi-static modal analysis and model reduction techniques that employ multipoint constraints (i.e., spider elements). With over 500,000 elements and 39 frictional contact surfaces, this represents one of the most complicated models to which these methods have been applied to date. The results to date are summarized and lessons learned are highlighted.
A sodium pool fire in the containment of a sodium-cooled fast reactor (SFR) plant can occur due to a pipe leak or break. Accumulation of the sodium in a pool would allow the sodium to react with the atmosphere of the containment, such as oxygen, to cause a fire. Sodium fire is important to model because the heat addition and aerosol generation that occur. Any fission products trapped in the leaked sodium coolant may also be released into the containment, which can affect workers and the public if the containment is breached. This paper describes progress of an international collaborative research in SFR sodium fire modeling between the United States and Japan under the framework of the Civil Nuclear Energy Research and Development Working Group (CNWG). In this collaboration between Sandia National Laboratories (SNL) and Japan Atomic Energy Agency (JAEA), the validation basis for and modeling capabilities of sodium pool fires in MELCOR of SNL and SPHINCS of JAEA are being assessed. Additional model improvements for the sodium pool fire in MELCOR are discussed. The MELCOR results for the sodium pool fire model enhancement in MELCOR agreed well with the JAEA's F7 pool fire experiments and compared closely with SPHINCS.
Conference Proceedings of the Society for Experimental Mechanics Series
Saunders, Brian E.; Vasconcellos, Rui M.G.; Kuether, Robert J.; Abdelkefi, Abdessattar
Dynamical systems containing contact/impact between parts can be modeled as piecewise-smooth reduced-order models. The most common example is freeplay, which can manifest as a loose support, worn hinges, or backlash. Freeplay causes very complex, nonlinear responses in a system that range from isolated resonances to grazing bifurcations to chaos. This can be an issue because classical solution methods, such as direct time integration (e.g., Runge-Kutta) or harmonic balance methods, can fail to accurately detect some of the nonlinear behavior or fail to run altogether. To deal with this limitation, researchers often approximate piecewise freeplay terms in the equations of motion using continuous, fully smooth functions. While this strategy can be convenient, it may not always be appropriate for use. For example, past investigation on freeplay in an aeroelastic control surface showed that, compared to the exact piecewise representation, some approximations are not as effective at capturing freeplay behavior as other ones. Another potential issue is the effectiveness of continuous representations at capturing grazing contacts and grazing-type bifurcations. These can cause the system to transition to high-amplitude responses with frequent contact/impact and be particularly damaging. In this work, a bifurcation study is performed on a model of a forced Duffing oscillator with freeplay nonlinearity. Various representations are used to approximate the freeplay including polynomial, absolute value, and hyperbolic tangent representations. Bifurcation analysis results for each type are compared to results using the exact piecewise-smooth representation computed using MATLAB® Event Location. The effectiveness of each representation is compared and ranked in terms of numerical accuracy, ability to capture multiple response types, ability to predict chaos, and computation time.
The Cramér-Rao Lower Bound (CRLB) is used as a classical benchmark to assess estimators. Online algorithms for estimating modal properties from ambient data, i.e., mode meters, can benefit from accurate estimates of forced oscillations. The CRLB provides insight into how well forced oscillation parameters, e.g., frequency and amplitude, can be estimated. Previous works have solved the lower bound under a single-channel PMU measurement; thus, this paper extends works further to study CRLB under two-channel PMU measurements. The goal is to study how correlated/uncorrelated noise can affect estimation accuracy. Interestingly, these studies shows that correlated noise can decrease the CRLB in some cases. This paper derives the CRLB for the two-channel case and discusses factors that affect the bound.
Neural networks (NN) have become almost ubiquitous with image classification, but in their standard form produce point estimates, with no measure of confidence. Bayesian neural networks (BNN) provide uncertainty quantification (UQ) for NN predictions and estimates through the posterior distribution. As NN are applied in more high-consequence applications, UQ is becoming a requirement. Automating systems can save time and money, but only if the operator can trust what the system outputs. BNN provide a solution to this problem by not only giving accurate predictions and estimates, but also an interval that includes reasonable values within a desired probability. Despite their positive attributes, BNN are notoriously difficult and time consuming to train. Traditional Bayesian methods use Markov Chain Monte Carlo (MCMC), but this is often brushed aside as being too slow. The most common method is variational inference (VI) due to its fast computation, but there are multiple concerns with its efficacy. MCMC is the gold standard and given enough time, will produce the correct result. VI, alternatively, is an approximation that converges asymptotically. Unfortunately (or fortunately), high consequence problems often do not live in the land of asymtopia so solutions like MCMC are preferable to approximations. We apply and compare MCMC-and VI-trained BNN in the context of target detection in hyperspectral imagery (HSI), where materials of interest can be identified by their unique spectral signature. This is a challenging field, due to the numerous permuting effects practical collection of HSI has on measured spectra. Both models are trained using out-of-the-box tools on a high fidelity HSI target detection scene. Both MCMC-and VI-trained BNN perform well overall at target detection on a simulated HSI scene. Splitting the test set predictions into two classes, high confidence and low confidence predictions, presents a path to automation. For the MCMC-trained BNN, the high confidence predictions have a 0.95 probability of detection with a false alarm rate of 0.05 when considering pixels with target abundance of 0.2. VI-trained BNN have a 0.25 probability of detection for the same, but its performance on high confidence sets matched MCMC for abundances >0.4. However, the VI-trained BNN on this scene required significant expert tuning to get these results while MCMC worked immediately. On neither scene was MCMC prohibitively time consuming, as is often assumed, but the networks we used were relatively small. This paper provides an example of how to utilize the benefits of UQ, but also to increase awareness that different training methods can give different results for the same model. If sufficient computational resources are available, the best approach rather than the fastest or most efficient should be used, especially for high consequence problems.
Quantum computers can now run interesting programs, but each processor’s capability—the set of programs that it can run successfully—is limited by hardware errors. These errors can be complicated, making it difficult to accurately predict a processor’s capability. Benchmarks can be used to measure capability directly, but current benchmarks have limited flexibility and scale poorly to many-qubit processors. We show how to construct scalable, efficiently verifiable benchmarks based on any program by using a technique that we call circuit mirroring. With it, we construct two flexible, scalable volumetric benchmarks based on randomized and periodically ordered programs. We use these benchmarks to map out the capabilities of twelve publicly available processors, and to measure the impact of program structure on each one. We find that standard error metrics are poor predictors of whether a program will run successfully on today’s hardware, and that current processors vary widely in their sensitivity to program structure.
A new reflected shock tunnel has been commissioned at Sandia capable of generating hypersonic environments at realistic flight enthalpies. The tunnel uses an existing free-piston driver and shock tube coupled to a conical nozzle to accelerate the flow to approximately Mach 9. The facility design process is outlined and compared to other ground test facilities. A representative flight enthalpy condition is designed using an in-house state-to-state solver and piston dynamics model and evaluated using quasi-1D modeling with the University of Queensland L1d code. This condition is demonstrated using canonical models and a calibration rake. A 25 cm core flow with 4.6 MJ/kg total enthalpy is achieved over an approximately 1 millisecond test time. Analysis shows that increasing piston mass should extend test time by a factor of 2-3.
Using the power balance method we estimate the maximum electric field on a conducting wall of a cavity containing an interior structure supporting eccentric coaxial modes in the frequency regime where the resonant modes are isolated from each other.
Magann, Alicia B.; Mccaul, Gerard; Rabitz, Herschel A.; Bondar, Denys I.
The characterization of mixtures of non-interacting, spectroscopically similar quantum components has important applications in chemistry, biology, and materials science. We introduce an approach based on quantum tracking control that allows for determining the relative concentrations of constituents in a quantum mixture, using a single pulse which enhances the distinguishability of components of the mixture and has a length that scales linearly with the number of mixture constituents. To illustrate the method, we consider two very distinct model systems: mixtures of diatomic molecules in the gas phase, as well as solid-state materials composed of a mixture of components. A set of numerical analyses are presented, showing strong performance in both settings.
ASHRAE and IBPSA-USA Building Simulation Conference
Villa, Daniel V.; Carvallo, Juan P.; Bianchi, Carlo; Lee, Sang H.
Heat waves are increasing in severity, duration, and frequency, making historical weather patterns insufficient for assessments of building resilience. This work introduces a stochastic weather generator called the multi-scenario extreme weather simulator (MEWS) that produces credible future heat waves. MEWS calculates statistical parameters from historical weather data and then shifts them using climate projections of increasing severity and frequency. MEWS is demonstrated using the EnergyPlus medium office prototype model for climate zone 4B using five climate scenarios to 2060. The results show how changes in climate and heat waves affect electric loads, peak loads, and thermal comfort with uncertainty.
Communication-assisted adaptive protection can improve the speed and selectivity of the protection system. However, in the event, that communication is disrupted to the relays from the centralized adaptive protection system, predicting the local relay protection settings is a viable alternative. This work evaluates the potential for machine learning to overcome these challenges by using the Prophet algorithm programmed into each relay to individually predict the time-dial (TDS) and pickup current (IPICKUP) settings. A modified IEEE 123 feeder was used to generate the data needed to train and test the Prophet algorithm to individually predict the TDS and IPICKUP settings. The models were evaluated using the mean average percentage error (MAPE) and the root mean squared error (RMSE) as metrics. The results show that the algorithms could accurately predict IPICKUP setting with an average MAPE accuracy of 99.961%, and the TDS setting with a average MAPE accuracy of 94.32% which is sufficient for protection parameter prediction.
Early on in 2018 Sandia recognized the Microsystems Engineering, Science and Applications (MESA) Programmatic Asset Lifecycle Planning capability to be unpredictable, inconsistent, reactive, and unable to provide strong linkage to the sponsor's needs. The impetus for this report is to share learnings from MESA's journey towards maturing this capability. This report describes re-building the foundational elements of MESA's Programmatic Asset Lifecycle Planning capability using a risk-based, Multi-Criteria Decision Analysis (MCDA) approach. To begin, MESA's decades-old Piano Chart + Ad Hoc Hybrid Methodology is described with a narrative of its strengths and weaknesses. Then its replacement, the MCDA /Analytical Hierarchy Process, is introduced with a discussion of its strengths and weaknesses. To generate a realistic Programmatic Asset Lifecycle Planning budget outlook, MESA used its rolling 20-year Extended Life Program Plan (MELPP) as a baseline. The new MCDA risk-based prioritization methodology implements DOE/NNSA guidelines for prioritization of DOE activities and provides a reliable, structured framework for combining expert judgement and stakeholder preferences according to an established scientific technique. An in-house Hybrid Decision Support System (HDSS) software application was developed to facilitate production of several key deliverables. The application enables analysis of the prioritization decisions with charts to display and provide linkage of MESA's funding requests to the stakeholders' priorities, strategic objectives, nuclear deterrence programs, MESA priorities, and much more.
Area efficient self-correcting flip-flops for use with triple modular redundant (TMR) soft-error hardened logic are implemented in a 12-nm finFET process technology. The TMR flip-flop slave latches self-correct in the clock low phase using Muller C-elements in the latch feedback. These C-elements are driven by the two redundant stored values and not by the slave latch itself, saving area over a similar implementation using majority gate feedback. These flip-flops are implemented as large shift-register arrays on a test chip and have been experimentally tested for their soft-error mitigation in static and dynamic modes of operation using heavy ions and protons. We show how high clock skew can result in susceptibility to soft-errors in the dynamic mode, and explain the potential failure mechanism.
A crucial component of field testing is the utilization of numerical models to better understand the system and the experimental data being collected. Meshing and modeling field tests is a complex and computationally demanding problem. Hexahedral elements cannot always reproduce experimental dimensions leading to grid orientation or geometric errors. Voronoi meshes can match complex geometries without sacrificing orthogonality. As a result, here we present a high-resolution 3D numerical study for the BATS heater test at the WIPP that compares both a standard non-deformed cartesian mesh along with a Voronoi mesh to match field data collected during a salt heater experiment.
Many, if not all, Waste Management Organisation programs will include criticality safety. As criticality safety in the long-term, i.e. considered over post-closure timescales in dedicated disposal facilities, is a unique challenge for geological disposal there is limited opportunity for sharing of experience within an individual organization/country. Therefore, sharing of experience and knowledge between WMOs to understand any similarities and differences will be beneficial in understanding where the approaches are similar and where they are not, and the reasons for this. To achieve this benefit a project on Post-Closure Criticality Safety has been established through the Implementing Geological Disposal - Technology Platform with the overall aim to facilitate the sharing of this knowledge. This project currently has 11 participating nations, including the United States and this paper presents the current position in the United States.