The primary subject of this Report is the description and characterization of results (voltages, currents, radiation dose and dose-rates) from the HERMES accelerator operated in the Outdoor Mode. The shots described range from 10266 – 10313, and were taken in late 2016. In the course of determining the most accurate estimates of voltage and current, a prescriptive procedure is developed to process the raw data posted to the HERMES database. The current estimates are tied to voltage determination using the MITL theory of Mendel, as modified by Schumer and Ottinger. The converter currents are accurately recorded due to newly calibrated monitors at the converter location. Additional historical information about the development of the HERMES current monitor set is included to enhance the archival value of this Report. The evolution of the TLD faceplate profile from non-peaked center to center-peaked is discussed, with hypotheses as to the cause. The prescriptive procedure discussed herein is accurate as of the day of printing. Should the prescription be modified and updated, this Report would also need updating.
This project will enable high-fidelity aerothermal simulations of hypersonic vehicles to be employed (1) to generate large databases with quantified uncertainties and (2) for rapid interactive simulation. The databases will increase the volume/quality of A4H data; rapid interactive simulation can enable arbitrary conditions/designs to be simulated on demand. We will achieve this by applying reduced-order-modeling techniques to aerothermal simulations.
On August 15th thru 17th, 2017 the Federal Radiological Monitoring and Assessment Center (FRMAC) Laboratory Analysis division, the FRMAC Fly Away Laboratory (FAL), the FRMAC Assessment division, and the Mobile Environmental Response Laboratory (MERL) held a training and capstone event for staff from the Environmental Protection Agency (EPA), Remote Sensing Laboratory (RSL), Lawrence Livermore National Laboratory (LLNL), and Sandia National Laboratories (SNL). LAB-100, "Sample Control Training", LAB-200 "QA Specialist Training", and LAB-300 "Laboratory Analysis Manager Training" was given the first two days of the event. The purpose of the training and capstone event was to meet training requirements for billeted FRMAC Lab Analysis staff from RSL, LLNL, and SNL as well as raise awareness of the FRMAC Lab Analysis process with EPA staff as part of a Federal Emergency Management Agency — Nuclear Incident Response Team (FEMA-NIRT) laboratory standardization project. An objective of the standardization project was to help improve the transition of operations from DOE to EPA during a response. To do this effectively, detailed knowledge of the FRMAC Lab Analysis process by the EPA is needed. This training provided a good opportunity for this knowledge transfer. A capstone was held after the two-day training event to allow participants to practice the skills they learned in a realistic scenario. A scenario that was previously developed for a quarterly Consequence Management drill (i.e. Dark Phoenix) was used as the basis for the capstone, with laboratory analysis focused injects used to drive the exercise play. Each position within the FRMAC Lab Analysis Division exercised to specific objectives and helped to uncover gaps in the established processes. The lessons learned during this capstone are broken out in the following categories: Sample Control, In-Situ Gamma Spectroscopy, Analysis Request Forms (ARF), Shipping, QA/QC, Fly Away Laboratory (FAL), and Management.
The classical problem of calculating the volume of the union of d-dimensional balls is known as "Union Volume." We present line-sampling approximation algorithms for Union Volume. Our methods may be extended to other Boolean operations, such as setminus; or to other shapes, such as hyper-rectangles. The deterministic, exact approaches for Union Volume do not scale well to high dimensions. However, we adapt several of these exact approaches to approximation algorithms based on sampling. We perform local sampling within each ball using lines. We have several variations, depending on how the overlapping volume is partitioned, and depending on whether radial, axis-aligned, or other line patterns are used. Our variations fall within the family of Monte Carlo sampling, and hence have about the same theoretical convergence rate, 1 /$\sqrt{M}$, where M is the number of samples. In our limited experiments, line-sampling proved more accurate per unit work than point samples, because a line sample provides more information, and the analytic equation for a sphere makes the calculation almost as fast. We performed a limited empirical study of the efficiency of these variations. We suggest a more extensive study for future work. We speculate that different ball arrangements, differentiated by the distribution of overlaps in terms of volume and degree, will benefit the most from patterns of line samples that preferentially capture those overlaps. Acknowledgement We thank Karl Bringman for explaining his BF-ApproxUnion (ApproxUnion) algorithm [3] to us. We thank Josiah Manson for pointing out that spoke darts oversample the center and we might get a better answer by uniform sampling. We thank Vijay Natarajan for suggesting random chord sampling. The authors are grateful to Brian Adams, Keith Dalbey, and Vicente Romero for useful technical discussions. This work was sponsored by the Laboratory Directed Research and Development (LDRD) Program at Sandia National Laboratories. This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Advanced Scientific Computing Research (ASCR), Applied Mathematics Program. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.
This report studies the efforts of the international community and the United States to verif)/ the denuclearization of various countries: Ukraine, South Africa, Iraq, Taiwan, and Libya. In doing so, it considers the verification of nuclear warhead destruction and the accounting of nuclear materials. Each case study contributes to the understanding we have of which verification procedures worked and which did not and what factors contributed to that success and which did not. The most important factor contributing to successful verification is the cooperation of the subject country. If a country has made the strategic decision to cooperate, then it is possible that verification can be successful. If the country chooses not to cooperate, verification might rest on random and unpredictable events. This unpredictability of verification is politically unacceptable. Even if verification is judged to be successful by the implementing agencies, outsiders can cast doubts on it by pointing out small and potentially unavoidable errors in material amounts verified. It is vitally important to systematically preserve forensic evidence, especially shipping and receiving records to avoid just such issues. Historically, such records are the most important evidence in verifying denuclearization. Technology is far less important than forensic analysis of records. It does play a supporting role in verifying some declarations but there can be an enormous delay in drawing conclusions caused by the necessity to analyze statistically large samples of materials. The confidence one gets from such analysis can be delayed well past the time it is politically significant. The most important advance in technology would be to accelerate that sample analysis process.
The agenda for this presentation covers the Model Authorized Product — Realization (MAPR); Project Background; Data Collected; Observations & Findings; Next Steps; MBE Level 3+; Research on 3D interactive viewable(s) (3DIV).
This report considers plane wave coupling to a transmission line consisting of a wire above a conducting ground. Comparisons are made for the two types of available source models, along with a discussion about the decomposition of the line currents. Simple circuit models are constructed for the terminating impedances at the ends of the line including radiation effects. Results from the transmission line with these loads show good agreement with full wave simulations.
A Sandia National Laboratories Member of the Workforce (MOW) experienced contact with electrical energy while performing work on an oil filter pump electrical system in the al wind turbine nacelle at Sandia National Laboratories Scaled Wind Turbine Facility (SWiFT). The Department of Energy (DOE) Sandia National Laboratories (SNL) Scaled Wind Farm Technology (SWiFT) facility does research and development (R&D) work in collaboration with Texas Tech University. The SWiFT facility includes three turbines for performing wind plant and turbine technology research in support of DOE's Wind Energy Technology Office. The current work ongoing at the site is primarily related to commissioning the three turbines to support ongoing DOE customer needs and requests. It was during the performance of commissioning tests of the hydraulic systems in the a1 turbine that a Sandia MOW experienced contact with electrical energy. There were multiple root and contributing causes that ultimately resulted in the electrical energy contact. These causes are summarized and aligned to their corrective actions in the corrective action plan table provided in Section 7(c). The purpose of this narrative section is to provide additional information and context
Sandia National Laboratories (SNL) Employee Health Services (EHS) is committed to promoting healthy, vibrant lives and embracing health. Since 1986, EHS has built a comprehensive, evidence-based program designed to measure and assess health risk prevalence, provide targeted and customizable services to address health risks, incentivize healthy behaviors, improve productivity, enhance quality of life, and lower healthcare costs for participants via collaboration between on-site and community-based providers. This unique partnership provides a broad scope of services that may not be available to employees solely through their health benefit plan, and allows a supportive, convenient approach that has proven enhanced health outcomes. EHS impacts over 12,000 SNL employees in Albuquerque, New Mexico. Corporate wellness is as important as ever as health issues and healthcare costs continue to rise. We use the 8-15-80 model as the foundation for our health program strategy: prevent or improve 8 modifiable behaviors and risks that contribute to 15 chronic health conditions that account for 80% of healthcare spending on chronic illnesses worldwide. We utilize patient-centered, cost-effective, community-connected care by providing free onsite services including the NCQA-recognized/AAAHC-accredited medical clinic, health management, preventive health, behavioral health, physical therapy, medical case management, acute care, emergency medical services, and more. These programs and services are an employer-paid benefit open to all SNL employees. The organization combines best practices, accredited programs, and top health care providers to bring employees the most comprehensive approach to health care.
The Virtual Environment for Reactor Applications (VERA) code suite is assessed in terms of capability and credibility against the Consortium for Advanced Simulation of Light Water Reactors (CASL) Verification and Validation Plan (presented herein) in the context of three selected challenge problems: CRUD-Induced Power Shift (CIPS), Departure from Nucleate Boiling (DNB), and Pellet-Clad Interaction (PCI). Capability refers to evidence of required functionality for capturing phenomena of interest while credibility refers to the evidence that provides confidence in the calculated results. For this assessment, each challenge problem defines a set of phenomenological requirements against which the VERA software is assessed. This approach, in turn, enables the focused assessment of only those capabilities relevant to the challenge problem. The evaluation of VERA against the challenge problem requirements represents a capability assessment. The mechanism for assessment is the Sandia-developed Predictive Capability Maturity Model (PCMM) that, for this assessment, evaluates VERA on 8 major criteria: (1) Representation and Geometric Fidelity, (2) Physics and Material Model Fidelity, (3) Software Quality Assurance and Engineering, (4) Code Verification, (5) Solution Verification, (6) Separate Effects Model Validation, (7) Integral Effects Model Validation, and (8) Uncertainty Quantification. For each attribute, a maturity score from zero to three is assigned in the context of each challenge problem. The evaluation of these eight elements constitutes the credibility assessment for VERA.
Successful system protection is critical to the feasibility of the DC microgrid system. This work focused on identifying the types of faults, challenges of protection, different fault detection schemes, and devices pertinent to DC microgrid systems. One of the main challenges of DC microgrid protection is the lack of guidelines and standards. The various parameters that improve the design of protection schemes were identified and discussed. Due to the absence of physical inertia, the resistive nature of the line impedance affects fault clearing time and system stability during faults. Therefore, the effectiveness of protection coordination systems with communication were also explored. A detailed literature review was done to identify possible grounding schemes and protection devices needed to ensure seamless power flow of grid-connected DC microgrids. Ultimately, it was identified that more analyses and experimentation are needed to develop optimized fault detection schemes with reduced fault clearing time.
This report is a sequel to [PC18], where we provided the detailed installation and testing instructions of Sandia's currently-being-developed Automatic Report Generator (ARG), for both Linux and macOS target platforms. In the current report, we extend these instructions to the case of Windows systems.
The summaries are provided as fulfillment of milestone M4SF-18SN080305022 and represent international coordination activities in disposal research funded by the US DOE Spent Fuel and Waste Storage and Technologies (SFWST) Campaign during Fiscal Year 2018.
The U.S. study of permanent geologic disposal options of spent nuclear fuel (SNF) and high-level radioactive waste (HLW) provided a technical basis for informing policy decisions regarding strategies for the management and disposal of radioactive waste requiring geologic isolation through the evaluation of potential impacts of waste forms on the feasibility and performance of representative generic concepts for geologic disposal. The goal of the study was to help inform relevant policy questions including: Is a "one-size-fits-all" repository a good strategic option for disposal? Do different waste types and forms perform differently enough in different disposal concepts that they warrant different treatment? Do some disposal concepts perform significantly better with or without specific waste types or forms?
This report houses the deliverables provided by Stress Engineering Services on the floating platform design identification studies and the detailed final design iterations. The results were obtained under contract to and in partnership with Sandia to iterate between the platform design and the aero-hydro-elastic load simulations of the coupled vertical-axis wind turbine system. Through the analysis summarized in this report, a tension-leg platform with multiple columns was identified as the optimal platform when considering cost and performance. The detailed design and cost estimate of this platform architecture was produced in the final phase of study which is also described within this report.
In this report, we investigate how manufacturing conditions result in the warpage of moderate density PMDI polyurethane foam (12-50 lb/ft3) when they are released from a mold. We have developed a multiphysics modeling framework to simulate the manufacturing process including resin injection, foaming and mold filling, gelation of the matrix, elevated cure, vitrification, cool down, and demolding. We have implemented this framework within the Sierra Mechanics Finite Element Code Suite. We couple Aria for flow, energy conservation, and foaming/curing kinetics with Adagio for the nonlinear viscoelastic solid response in a multi-staged simulation process flow. We calibrate a model for the PMDI-10S (10 lb/ft3 free rise foam) through a suite of characterization data presented here to calibrate the solid cure behavior of the foam. The model is then used and compared to a benchmark experiment, the manufacturing and warpage over 1 year of a 10 cm by 10 cm by 2.5 cm foam "staple". This component features both slender and thick regions that warp considerably differently over time. Qualitative agreement between the model and the experiment is achieved but quantitative accuracy is not.
Sandia National Laboratories has tested and evaluated a new digitizer, the Affinity, manufactured by Guralp Systems Ltd. These digitizers are used to record sensor output for seismic and infrasound monitoring applications. The purpose of the digitizer evaluation was to measure the performance characteristics in such areas as power consumption, input impedance, sensitivity, full scale, self-noise, dynamic range, system noise, response, passband, and timing. The Affinity digitizer is Guralp's latest release in their digitizer product line. The Affinity is available with either 4 or 8 channels at 24 bit resolution. In addition to the 24 bit channels, 16 multiplexed low resolution channels are provided. Other features include the means to accept multiple types of timing sources (e.g. GPS, NTP and PTP) and a web page interface for command and control of the unit.
Sandia National Laboratories has tested and evaluated a new digitizer, the Q330HR, manufactured by Quanterra. These digitizers are used to record sensor output for seismic and infrasound monitoring applications. The purpose of the digitizer evaluation was to measure the performance characteristics in such areas as power consumption, input impedance, sensitivity, full scale, self-noise, dynamic range, system noise, response, passband, and timing. The Q330HR is Quanterra’s improved Q330 datalogger with a 26 bits of resolution on channels 1-3 and a 24 bits of resolution on channels 4-6 (26 bit is optional). The Quanterra Q330HR is being evaluated for potential use U.S. Air Force seismic monitoring systems as part of their Next Generation Qualification effort.
Sandia National Laboratories has tested and evaluated a new digitizer, the Centaur, manufactured by Nanometrics. These digitizers are used to record sensor output for seismic and infrasound monitoring applications. The purpose of the digitizer evaluation was to measure the performance characteristics in such areas as power consumption, input impedance, sensitivity, full scale, self-noise, dynamic range, system noise, response, passband, and timing. The Centaur digitizer is Nanometrics’ replacement for their Taurus digitizer and marks Nanometrics first 6 channel, 24 bit resolution system. Other improvements include LED status indicators on the top of the unit, providing basic status of the core systems of a seismic station (e.g. timing, sensor SOH, storage, etc), an optional wifi system allowing password protected access to the unit and a web interface for monitoring and configuration of the unit. The Nanometrics Centaur is being evaluated for potential use U.S. Air Force seismic monitoring systems as part of their Next Generation Qualification effort.
The levelized cost of energy for an offshore wind plant consisting of floating vertical-axis wind turbines is studied in this report. A 5 MW Darrieus vertical-axis wind turbine rotor is used as the study turbine as this architecture was determined to have the greatest ability to reduce the system cost. The rotor structural design was used with blade manufacturing cost model studies to estimate its cost. A two-bladed, carbon fiber rotor was selected in this analysis since the lower topside mass resulted in a reduction of the platform costs which exceeded the increased rotor cost. A direct-drive, medium efficiency drivetrain was designed which represents 25% of the costs and 45% of the mass of the combined rotor/drivetrain system. A direct-drive, permanent magnet generator drivetrain was selected due to the improved reliability of this type of system, while the cost was not significantly higher than for geared drivetrains. A platform was designed by first identifying the optimal architecture for the vertical-axis wind turbine at a water depth of 150 m. A survey was performed of floating platform types, and six characteristic designs were analyzed which span the range of stability mechanisms available to floating systems. A multi-cellular tension-leg platform was identified as the lowest cost platform which additionally provided some interesting performance benefits. The small motions of the tension-leg platform benefit the system energy capture while limiting inertial loads placed on the rotor’s tower and blades. A final design was produced for the multi-cellular tension-leg platform considering operational fatigue, storm wind and wave conditions, and tow-out design cases. The driving design load was stability during tow-out while ballasting the platform. System levelized cost of energy was calculated, including operational expenses and balance of system costs estimated for the wind plant. Opportunities for reduction in the component costs are predicted and used to make projections of the system levelized cost of energy for future developments. The opportunities and challenges for floating vertical-axis wind turbines are identified by the system design and levelized cost of energy analysis.
The moisture absorption behavior of two fiber reinforced composite materials was evaluated in a unidirectional manner The flat materials were exposed to varying humidity and temperature conditions inside of an environmental chamber in order to determine their effective moisture equilibrium (M m ) and moisture absorption rate (D z ). Two-ply (thin) and four-ply (thick) materials were utilized to obtain M,,, and Dz, respectively. The results obtained from laboratory work were then compared to modeling data to better understand the material properties. Predictions capabilities were built to forecast the maximum moisture content, time required for saturation, and the moisture content at any given humidity and temperature. A case study was included to demonstrate this capability. Also of interest were cubed samples to investigate directionality preferences in water immersion studies. Several coatings were evaluated for their water permeation properties. Further dissemination authorized to the Department of Energy and DOE contractors only; other requests shall be approved by the originating facility or higher DOE programmatic authority.
This report compares ATLOG modeling results for the response of a finite-length dissipative buried conductor interacting with a conducting ground to a measurement taken November 2016 at the High-Energy Radiation Megavolt Electron Source (HERMES) facility. We use the ATLOG frequency-domain method based on transmission line theory. Estimates of the impedance per unit length and admittance per unit length for a cable laying in a PVC pipe embedded in a concrete block are reported. Current wave shapes from both a single conductor and composite differential mode and antenna mode arrangements are close to those observed in the experiments.
Narratives about water resources have evolved, transitioning from a sole focus on physical and biological dimensions to incorporate social dynamics Recently, the importance of understanding the visibility of water resources through media coverage has gained attention. This study leverages recent advancements in natural language processing (NLP) methods to characterize and understand patterns in water narratives, specifically in 4 local newspapers in Utah and Georgia. Analysis of the corpus identified coherent topics on a variety of water resources issues, including weather and pollution. Closer inspection of the topics revealed temporal and spatial variations in coverage, with a topic on hurricanes exhibiting cyclical patterns whereas a topic on tribal issues showed coverage predominantly in the western newspapers. We also analyzed the dataset for sentiments, identifying similar categories of words on trust and fear emerging in the narratives across newspaper sources. An analysis of novelty, transience, and resonance using Kullback-Leibler Divergence techniques revealed that topics with high novelty generally contained high transience and marginally high resonance over time. Although additional analysis needs to be conducted, the methods explored in this analysis demonstrate the potential of NLP methods to characterize water narratives in media coverage.
Bieberdorf, Nathan; Towner, Zachary; Hubbard, Neal B.; Gerstle, Walter
In this work, various material models were studied for their ability to simulate puncture in a thin aluminum 7075-T651 plate due to low-velocity probe impact. Material models were generated by mixing and matching various work hardening laws with different failure criteria, and several hybrid material models were investigated. Finite element simulations of aluminum impact-response, based on each material model, were employed to predict the energy required for puncture and final plate tear-out geometry. Probes of different size and shape were used to impose various loading regimes, and numerical predictions were compared to experimental results from a previous study. It was found that no single combination of hardening and failure laws yielded universally accurate data, but that several material models could be used more reliably than others. Further, the importance of obtaining unique parameter-sets for work-hardening and failure criteria was illustrated.
CSP Dish systems are parabolic mirror structures that track the sun in two axes, focusing the Direct Normal insolation (DNI) to a point or spot on a boom or tripod mounted to the tracking dish structure. This focused light is typically utilized in-situ to operate a heat engine, such as a Stirling cycle, Brayton cycle, or Rankine cycle engine to make electricity. Other dish systems have been used to generate steam for a centralized engine fed by multiple dishes, or to operate thermochemical processes for industrial use, storage, or creation of fuels. Because the dish is always pointing at the sun, a well-designed dish system has a very high concentration ratio, allowing the generation of high temperatures, leading to high thermodynamic efficiencies.