Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

We address the problem of partitioning and dynamic load balancing on clusters with heterogeneous hardware resources. We propose DRUM, a model that encapsulates hardware resources and their interconnection topology. DRUM provides monitoring facilities for dynamic evaluation of communication, memory, and processing capabilities. Heterogeneity is quantified by merging the information from the monitors to produce a scalar number called 'power.' This power allows DRUM to be used easily by existing load-balancing procedures such as those in the Zoltan Toolkit while placing minimal burden on application programmers. We demonstrate the use of DRUM to guide load balancing in the adaptive solution of a Laplace equation on a heterogeneous cluster. We observed a significant reduction in execution time compared to traditional methods.

Many problems from engineering and the sciences require the solution of sequences of linear systems where the matrix and right-hand side change from one system to the next, and the linear systems are not available simultaneously. We review a class of Krylov subspace methods for sequences of linear systems, which can significantly reduce the cost of solving the next system in the sequence by 'recycling' subspace information from previous systems. These methods have been successfully applied to sequences of linear systems arising from several different application areas. We analyze a particular method, GCRO-DR, that recycles approximate invariant subspaces, and establish residual bounds that suggest a convergence rate similar to one obtained by removing select eigenvector components from the initial residual. We review implications of this analysis, which suggests problem classes where we expect this technique to be particularly effective. From this analysis and related numerical experiments we also demonstrate that recycling the invariant subspace corresponding to the eigenvalues of smallest absolute magnitude is often not the best choice, especially for nonsymmetric problems, and that GCRO-DR will, in practice, select better subspaces. These results suggest possibilities for improvement in the subspace selection process.

Abstract not provided.

Abstract not provided.

The present ITSE journal special issue on 'Learning About Social Interaction through Gaming' is the result of an invitation to the attendees of a one-day workshop on 'Social Learning Through Gaming' co-organized by the guest editors and held at the Human Factors in Computing Systems (CHI) conference on April 26, 2004 in Vienna, Austria. CHI is one of the premiere conferences on human-computer interaction. CHI 2004 attracted hundreds of delegates from all over the world. The CHI workshop program results from a competitive selection process. The Social Learning through Gaming workshop was filled to capacity and attended by approximately 25 participants from Europe and North America who submitted position papers that were refereed and selected for participation based on the relevancy and innovativeness of the research. The participants came together to share research on play, learning, games, interactive technologies, and what playing and designing games can teach us about social behaviors. The present special issue focuses on learning about social aspects through gaming: learning to socialize through games and learning games through social behavior.

The presence of mechanical joints--typified by the lap joint--in otherwise linear structures has been accommodated in structural dynamics via ad hoc methods for a century. The methods range from tuning linear models to approximate non-linear behavior in restricted load ranges to various methods which introduce joint dissipation in a post-processing stage. Other methods, employing constitutive models for the joints are being developed and their routine use is on the horizon.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We have measured the temperature dependence of mechanical dissipation in tetrahedral amorphous carbon flexural and torsional resonators over the temperature range from 300 to 1023 K. The mechanical dissipation was found to be controlled by defects within the material, and the magnitude and temperature dependence of the dissipation were found to depend on whether flexural or torsional vibrational modes were excited. The defects that were active under flexural stresses have a relatively flat concentration from 0.4 to 0.7 eV with an ever increasing defect concentration up to 1.9 eV. Under shear stresses (torsion), the defect activation energies increase immediately beginning at 0.4 eV, with increasing defect concentration at higher energies.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Solid solutions of lead-based perovskites are the backbone materials of the piezoelectric components for transducer, actuator, and resonator applications. These components, typically small in size, are fabricated from large sintered ceramic slugs using grinding and lapping processes. These operations increase manufacturing costs and produce a large hazardous waste stream, especially when component size decreases. To reduce costs and hazardous wastes associated with the production of these components, an injection molding technique is being investigated to replace the machining processes. The first step in the new technique is to compound an organic carrier with a ceramic powder. The organic carrier is a thermoplastic based system composed of a main carrier, a binder, and a surfactant. Understanding the rheology of the compounded material is necessary to minimize the creation of defects such as voids or cavities during the injection-molding process. An experiment was performed to model the effects of changes in the composition and processing of the material on the rheological behavior. Factors studied included: the surfactant of the organic carrier system, the solid loading of the compounded material, and compounding time. The effects of these factors on the viscosity of the material were investigated.

Abstract not provided.

We report the experimental realization of a new type of optical parametric oscillator in which oscillation is achieved by polarization rotation in a linear retarder, followed by nonlinear polarization mixing. The mixing is performed by a type II degenerate parametric downconversion in a periodically poled KTP crystal pumped by a 1064 nm pulsed Nd:YAG pump. A single, linearly polarized beam, precisely at the degenerate wavelength is generated. The output spectrum has a narrow linewidth (below the instrumentation bandwidth of 1 nm) and is highly stable with respect to variations in the crystal temperature.

Abstract not provided.

Abstract not provided.

Concepts from Complexity Science are valuable and allow a simulation approach for critical infrastructures that is flexible and has wide ranging applications.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

A large-scale field demonstration comparing final landfill cover designs was constructed and monitored at Sandia National Laboratories in Albuquerque, New Mexico. Two conventional designs (a RCRA Subtitle 'D' Soil Cover and a RCRA Subtitle 'C' Compacted Clay Cover) were constructed side-by-side with four alternative cover test plots designed for arid environments. The demonstration was intended to evaluate the various cover designs based on their respective water balance performance, ease and reliability of construction, and cost. A portion of this project involves the characterization of vegetation establishment and growth on the landfill covers. The various prototype landfill covers were expected to have varying flux rates (Dwyer et al 2000). The landfill covers were further expected to influence vegetation establishment and growth, which may impact site erosion potential and long-term site integrity. Objectives of this phase were to quantify the types of plants occupying each site, the percentage of ground covered by these plants, the density (number of plants per unit area) of plants, and the plant biomass production. The results of this vegetation analysis are presented in this report.3 DRAFT07/06/14AcknowledgementsWe would like to thank all technical and support staff from Sandia and the USDA Forest Service's Rocky Mountain Station not included in the authors' list of this document for their valuable contributions to this research. We would also like to acknowledge the Department of Energy's Subsurface Contaminants Focus Area for funding this work.4

Abstract not provided.

Abstract not provided.

This Work Plan identifies and outlines interim measures to address nitrate contamination in groundwater at the Burn Site, Sandia National Laboratories/New Mexico. The New Mexico Environment Department has required implementation of interim measures for nitrate-contaminated groundwater at the Burn Site. The purpose of interim measures is to prevent human or environmental exposure to nitrate-contaminated groundwater originating from the Burn Site. This Work Plan details a summary of current information about the Burn Site, interim measures activities for stabilization, and project management responsibilities to accomplish this purpose.

Abstract not provided.

Abstract not provided.

We show that the orientation of pentacene molecules is controlled by the electronic structure of the surface on which they are deposited. We suggest that the near-Fermi level density of states above the surface controls the interaction of the substrate with the pentacene {pi} orbitals. A reduction of this density as compared to noble metals, realized in semimetallic Bi(001) and Si(111)(5 x 2)Au surfaces, results in pentacene standing up. Interestingly, pentacene grown on Bi(001) is highly ordered, yielding the first vertically oriented epitaxial pentacene thin films observed to date.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This report documents activities related to the ASCI AD Resistance Weld Process Modeling Project AD2003-15. Activities up to and including FY2004 are discussed. This was the third year for this multi year project, the objective of which is to position the SIERRA computational tools for the solution of resistance welding problems. The process of interest is a three-way coupled problem involving current flow, temperature buildup and large plastic deformation. The DSW application is the reclamation stem weld used in the manufacture of high pressure gas bottles. This is the first year the CALAGIO suite of codes (eCALORE, CALORE, and ADAGIO) was used to successfully solve a three-way coupled problem in SIERRA. This report discusses the application of CALAGIO to the tapered bar acceptance problem and a similar but independent tapered bar simulation of a companion C6 experiment. New additions to the EMMI constitutive model and issues related to CALAGIO performance are also discussed.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Classical density functional theory (DFT) is applied to study properties of fully detailed, realistic models of poly(dimethylsiloxane) liquids near silica surfaces and compared to results from molecular dynamics simulations. In solving the DFT equations, the direct correlation functions are obtained from the polymer reference interaction site model (PRISM) theory for the repulsive parts of the interatomic interactions, and the attractions are treated via the random-phase approximation (RPA). Good agreement between density profiles calculated from DFT and from the simulations is obtained with empirical scaling of the direct correlation functions. Separate scaling factors are required for the PRISM and RPA parts of the direct correlation functions. Theoretical predictions of stress profiles, normal pressure, and surface tensions are also in reasonable agreement with simulation results.

Abstract not provided.

In the crystal structure of the title compound, C{sub 4}H{sub 4}N{sub 2}O{sub 3}, the packing is dominated by intermolecular carbonyl-carbonyl interactions and N-H...O hydrogen bonds.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The solution of the governing steady transport equations for momentum, heat and mass transfer in fluids undergoing non-equilibrium chemical reactions can be extremely challenging. The difficulties arise from both the complexity of the nonlinear solution behavior as well as the nonlinear, coupled, non-symmetric nature of the system of algebraic equations that results from spatial discretization of the PDEs. In this paper, we briefly review progress on developing a stabilized finite element (FE) capability for numerical solution of these challenging problems. The discussion considers the stabilized FE formulation for the low Mach number Navier-Stokes equations with heat and mass transport with non-equilibrium chemical reactions, and the solution methods necessary for detailed analysis of these complex systems. The solution algorithms include robust nonlinear and linear solution schemes, parameter continuation methods, and linear stability analysis techniques. Our discussion considers computational efficiency, scalability, and some implementation issues of the solution methods. Computational results are presented for a CFD benchmark problem as well as for a number of large-scale, 2D and 3D, engineering transport/reaction applications.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Highly ordered gold nanocrystal (NC)/silica films are synthesized by self-assembly of water-soluble gold NC micelles and silica using a sol-gel spin coating technique. The optical properties are analyzed using ellipsometry and ultraviolet-visible spectroscopy. Transmission and absorption spectra were measured for wavelengths ranging from 200 to 2000 nm. The absorption spectra show a strong surface plasmon absorption band at {approx}520 nm for all samples. Charge transport behavior of the films was examined using metal-oxide-semiconductor (MOS) and metal-insulator-metal (MIM) structures. MOS capacitor samples exhibit charge storage with discharge behavior dominated by electron transport within the gold NC arrays. Low temperature current-voltage measurements on MIM devices reveal electrical conduction with a thermal activation energy of {approx}90 meV. For temperatures less than 100 K, the I-V characteristics of the NC film exhibits a strong coulomb blockade effect, with a threshold voltage of {approx}0.5 V measured at 78 K.

A new approach is proposed for the a posteriori error estimation of both global spatial and parameter error in parameterized nonlinear reaction-diffusion problems. The technique is based on linear equations relating the linearized spatial and parameter error to the weak residual. Computable local element error indicators are derived for local contributions to the global spatial and parameter error, along with corresponding global error indicators. The effectiveness of the error indicators is demonstrated using model problems for the case of regular points and simple turning points. In addition, a new turning point predictor and adaptive algorithm for accurately computing turning points are introduced.

Abstract not provided.

The intense magnetic field produced by the 20 MA Z accelerator is used as an impulsive pressure source to accelerate metal flyer plates to high velocity for the purpose of performing plate impact, shock wave experiments. This capability has been significantly enhanced by the recently developed pulse shaping capability of Z, which enables tailoring the rise time to peak current for a specific material and drive pressure to avoid shock formation within the flyer plate during acceleration. Consequently, full advantage can be taken of the available current to achieve the maximum possible magnetic drive pressure. In this way, peak magnetic drive pressures up to 490 GPa have been produced, which shocklessly accelerated 850 {micro}m aluminum (6061-T6) flyer plates to peak velocities of 34 km/s. We discuss magnetohydrodynamic (MHD) simulations that are used to optimize the magnetic pressure for a given flyer load and to determine the shape of the current rise time that precludes shock formation within the flyer during acceleration to peak velocity. In addition, we present results pertaining to plate impact, shock wave experiments in which the aluminum flyer plates were magnetically accelerated across a vacuum gap and impacted z-cut, {alpha}-quartz targets. Accurate measurements of resulting quartz shock velocities are presented and analyzed through high-fidelity MHD simulations enhanced using optimization techniques. Results show that a fraction of the flyer remains at solid density at impact, that the fraction of material at solid density decreases with increasing magnetic pressure, and that the observed abrupt decrease in the quartz shock velocity is well correlated with the melt transition in the aluminum flyer.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We present results of an off-lattice simulation of a two-component planar system, as a model for lateral organization of cholesterol molecules in lipid-cholesterol assemblies. We explore the existence of 'superlattice' structures even in fluid systems, in the absence of an underlying translational long-range order, and study their coupling to hexatic or bond-orientational order. We discuss our results in context of geometric superlattice theories and 'condensation complexes' in understanding a variety of experiments in artificial lipid-cholesterol assemblies.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

A grating-gated field-effect transistor fabricated from a single-quantum well in a high-mobility GaAs-AlGaAs heterostructure is shown to function as a continuously electrically tunable photodetector of terahertz radiation via excitation of resonant plasmon modes in the well. Different harmonics of the plasmon wave vector are mapped, showing different branches of the dispersion relation. As a function of temperature, the resonant response magnitude peaks at around 30 K. Both photovoltaic and photoconductive responses have been observed under different incident power and bias conditions.

Abstract not provided.

Abstract not provided.

Abstract not provided.

As current experimental and simulation methods cannot determine the mobility of flat boundaries across the large misorientation phase space, we have developed a computational method for imposing an artificial driving force on boundaries. In a molecular dynamics simulation, this allows us to go beyond the inherent timescale restrictions of the technique and induce non-negligible motion in flat boundaries of arbitrary misorientation. For different series of symmetric boundaries, we find both expected and unexpected results. In general, mobility increases as the grain boundary plane deviates from (111), but high-coincidence and low-angle boundaries represent special cases. These results agree with and enrich experimental observations.

The overall goal of this joint research project was to develop and demonstrate advanced sensors and computational technology for continuous monitoring of the condition of components, structures, and systems in advanced and next-generation nuclear power plants (NPPs). This project included investigating and adapting several advanced sensor technologies from Korean and US national laboratory research communities, some of which were developed and applied in non-nuclear industries. The project team investigated and developed sophisticated signal processing, noise reduction, and pattern recognition techniques and algorithms. The researchers installed sensors and conducted condition monitoring tests on two test loops, a check valve (an active component) and a piping elbow (a passive component), to demonstrate the feasibility of using advanced sensors and computational technology to achieve the project goal. Acoustic emission (AE) devices, optical fiber sensors, accelerometers, and ultrasonic transducers (UTs) were used to detect mechanical vibratory response of check valve and piping elbow in normal and degraded configurations. Chemical sensors were also installed to monitor the water chemistry in the piping elbow test loop. Analysis results of processed sensor data indicate that it is feasible to differentiate between the normal and degraded (with selected degradation mechanisms) configurations of these two components from the acquired sensor signals, but it is questionable that these methods can reliably identify the level and type of degradation. Additional research and development efforts are needed to refine the differentiation techniques and to reduce the level of uncertainties.

Abstract not provided.

Abstract not provided.

Guidelines to Improve Airport Preparedness Against Chemical and Biological Terrorism is a 100-page document that makes concrete recommendations on improving security and assessing vulnerable areas and helps its readers understand the nature of chemical and biological attacks. The report has been turned over to Airports Council International (ACI) and the American Association of Airport Executives (AAAE), two organizations that together represent the interests of thousands of airport personnel and facilities in the U.S. and around the world.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The annual program report provides detailed information about all aspects of the SNL/CA Environmental Planning and Ecology Program for a given calendar year. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. The 2005 program report describes the activities undertaken during the past year, and activities planned in future years to implement the Planning and Ecology Program, one of six programs that supports environmental management at SNL/CA.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Variables influencing inferences about a stranger's goal during an unsolicited social interaction were explored. Experiment 1 developed a procedure for identifying cues. Experiments 2 and 3 assessed the relative importance of various cues (space, time, characteristics of oneself, characteristics of the stranger, and the stranger's behavior) for goal judgments. Results indicated that situational context cues informed goal judgments in ways that were consistent with diagnosticity ratings and typicality ratings of those cues. Stranger characteristics and stranger behaviors affected goal judgments more than would be expected from these quantitative measures of their informativeness. Nonetheless, the results are consistent with a mental model view that assumes perceivers monitor situational cues present during interactions and that goal inferences are guided by the informativeness of these cues.

Sandia national laboratories (SNL) and lockheed martin MS2 are designing an electromagnetic missile launcher (EMML) for naval applications. The EMML uses an induction coilgun topology with the requirement of launching a 3600 lb. missile up to a velocity of 40 m/s. To demonstrate the feasibility of the electromagnetic propulsion design, a demonstrator launcher was built that consists of approximately 10% of the propulsion coils needed for a tactical design. The demonstrator verified the design by launching a 1430 lb weighted sled to a height of 24 ft in mid-December 2004 (Figure 1). This paper provides the general launcher design, specific pulsed power system component details, system operation, and demonstration results.

Abstract not provided.

Abstract not provided.

In this study, we perform molecular dynamics simulations of adhesive contact and friction between alkylsilane Si(OH){sub 3}(CX{sub 2}){sub 10}CX{sub 3} and alkoxylsilane Si(OH){sub 2}(CX{sub 2}){sub 10}CX{sub 3} (where X = H or F) self-assembled monolayers (SAMs) on an amorphous silica substrate. The alkylsilane SAMs are primarily hydrogen-bonded or physisorbed to the surface. The alkoxylsilane SAMs are covalently bonded or chemisorbed to the surface. Previously, we studied the chemisorbed systems. In this work, we study the physisorbed systems and compare the tribological properties with the chemisorbed systems. Furthermore, we examine how water at the interface of the SAMs and substrate affects the tribological properties of the physisorbed systems. When less than a third of a monolayer is present, very little difference in the microscopic friction coefficient {mu} or shear stresses is observed. For increasing amounts of water, the values of {mu} and the shear stresses decrease; this effect is somewhat more pronounced for fluorocarbon alkylsilane SAMs than for the hydrocarbon SAMs. The observed decrease in friction is a consequence of a slip plane that occurs in the water as the amount of water is increased. We studied the frictional behavior using relative shear velocities ranging from v = 2 cm/s to 2 m/s. Similar to previously reported results for alkoxylsilane SAMs, the values of the measured stress and {mu} for the alkylsilane SAM systems decrease monotonically with v.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We present extensive simulations modeling the casting of multiblock polymer films by evaporation. The domain structure of the resulting film is strongly affected by varying the relative stiffness of the coblocks. The morphology changes from a bicontinuous lamellar phase when both blocks are flexible to a small-scale phase-separated phase with isolated domains as the stiffness of one of the blocks increases. As the relative stiffness of the blocks changes, the rate of evaporation, interfacial width, and morphology of the system changes. The findings can be used to tailor membrane morphology of interest to fuel-cell applications where the morphology is important for proton conduction.

Abstract not provided.

Abstract not provided.

While it had been known for a long time how to transform an asymmetric traveling salesman (ATS) problem on the complete graph with n vertices into a symmetric traveling salesman (STS) problem on an incomplete graph with 2n vertices, no method was available for using this correspondence to derive facets of the symmetric polytope from facets of the asymmetric polytope until the work of E. Balas and M. Fischetti in [Lifted cycle inequalities for the asymmetric traveling salesman problem, Mathematics of Operations Research 24 (2) (1999) 273-292] suggested an approach. The original Balas-Fischetti method uses a standard sequential lifting procedure for the computation of the coefficient of the edges that are missing in the incomplete STS graph, which is a difficult task when addressing classes of (as opposed to single) inequalities. In this paper we introduce a systematic procedure for accomplishing the lifting task. The procedure exploits the structure of the tight STS tours and organizes them into a suitable tree structure. The potential of the method is illustrated by deriving large new classes of facet-defining STS inequalities.

Abstract not provided.

We report the demonstration of distributed-feedback terahertz quantum-cascade lasers based on a first-order grating fabricated via a lateral corrugation in a double-sided metal ridge waveguide. The phase of the facet reflection was precisely set by lithographically defined facets by dry etching. Single-mode emission was observed at low to moderate injection currents, although multimode emission was observed far beyond threshold owing to spatial hole burning. Finite-element simulations were used to calculate the modal and threshold characteristics for these devices, with results in good agreement with experiments.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This document is intended to serve as a users guide for the time-domain atmospheric acoustic propagation suite (TDAAPS) program developed as part of the Department of Defense High-Performance Modernization Office (HPCMP) Common High-Performance Computing Scalable Software Initiative (CHSSI). TDAAPS performs staggered-grid finite-difference modeling of the acoustic velocity-pressure system with the incorporation of spatially inhomogeneous winds. Wherever practical the control structure of the codes are written in C++ using an object oriented design. Sections of code where a large number of calculations are required are written in C or F77 in order to enable better compiler optimization of these sections. The TDAAPS program conforms to a UNIX style calling interface. Most of the actions of the codes are controlled by adding flags to the invoking command line. This document presents a large number of examples and provides new users with the necessary background to perform acoustic modeling with TDAAPS.

Abstract not provided.

Near-edge X-ray absorption fine structure spectroscopy (NEXAFS) is utilized to provide insight into surface chemical effects in model photoresist films. First, NEXAFS was used to examine the resist/air interface including surface segregation of a photoacid generator (PAG) and the extent of surface deprotection in the film. The concentration of PAG at the resist-air interface was higher than the bulk concentration, which led to a faster deprotection rate at that interface. Second, a NEXAFS depth profiling technique was utilized to probe for compositional gradients in model resist line edge regions. In the model line edge region, the surface composition profile for the developed line edge was dependent on the post exposure bake time. © 2005 American Chemical Society.

Synchrotron-source X-ray computerized microtomography (CMT) was used to evaluate the adsorptive properties of aggregate soil samples. A linear relationship between measured mean mass attenuation coefficient (σ) and mass fraction iron was generated by imaging mineral standards with known iron contents. On the basis of reported stoichiometries of the clay minerals and identifications of iron oxyhydroxides (1), we calculated the mass fraction iron and iron oxyhydroxide in the intergranular material. The mass fractions of iron were estimated to range from 0.17 to 0.22 for measurements made at 18 keV and from 0.18 to 0.21 for measurements made at 26 keV. One aggregate sample also contained regions within the intergranular material with mass fraction iron ranging from 0.29 to 0.31 and from 0.33 to 0.36 for the 18 and 26 keV measurements, respectively. The mass fraction iron oxyhydroxide ranged from 0.18 to 0.35 for the low-iron intergranular material and from 0.40 to 0.59 for the high-iron intergranular material. Using absorption edge difference imaging with CMT, we visualized cesium on the intergranular material, presumably because of adsorption and possible exchange reactions. By characterizing the mass fraction iron, the mass fraction iron oxyhydroxide, and the adsorptive capacity of these soil mineral aggregates, we provide information useful for conceptualization, development, and parametrization of transport models. © 2005 American Chemical Society.

The properties of a particle composite can be controlled by organizing the particles into assemblies. The properties of the composite will depend on the structure of the particle assemblies, and for any give property there is some optimal structure. Through simulation and experiment we show that the application of heterodyned triaxial magnetic or electric fields generates structures that optimize the magnetic and dielectric properties of particle composites. We suggest that optimizing these properties optimizes other properties, such as transport properties, and we give as one example of this optimization the magnetostriction of magnetic particle composites formed in a silicone elastomer. © 2005 Elsevier Ltd. All rights reserved.

A new aminosilicate, sol-gel derived microporous inorganic membrane has been developed for enhanced CO2 separation in applications such as removal of metabolic CO2 from the breathing loop of the NASA extravehicular mobility unit (EMU), natural gas purification, or CO2 capture from coal-fired power plant emissions. This membrane consists of an inorganic, amorphous silica matrix of pore size 4-5 Å, containing randomly dispersed amine (NH2) functional groups in order to enhance its CO2 selectivity, due to preferential adsorption of CO 2 in the membrane pore walls and simultaneous blocking of permeation of other gases (O2, N2 and CH4). It is found that the gas feed condition during permeation (partial pressure of CO 2, relative humidity), post-synthetic treatments and aging, affect significantly the separation performance of the membranes. At this stage of development, with feeds of 1-20 vol.% CO2 and 0-40% relative humidity at 22 °C, the highest CO2:N2 separation factor was in the range 100-200, while the CO2 permeance was in the range 0.1-1.5 cm3 (STP)/(cm2 min atm). The results suggest that controlling the membrane pore size and method of activation of amine groups are the most critical factors for improving the CO 2-permselectivity of the membrane. © 2004 Elsevier B.V. All rights reserved.

We present pulse shaping techniques to obtain compressive stress - strain data for elastic - plastic materials with a split Hopkinson pressure bar. The conventional split Hopkinson pressure bar apparatus is modified by placing a combination of copper and steel pulse shapers on the impact surface of the incident bar. After impact by the striker bar, the copper - steel pulse shaper deforms plastically and spreads the pulse in the incident bar so that the sample is nearly in dynamic stress equilibrium and has a nearly constant strain rate in the plastic response region. We present analytical models and data that show a broad range of incident strain pulses can be obtained by varying the pulse shaper geometry and striking velocity. For an application, we present compressive stress - strain data for 4340 Rc 43 steel. © 2005 Society for Experimental Mechanics.

Failure modeling is inherently a multi length scale phenomenon that requires a failure model and a computational method that solves for stress/strain gradients at interesting locations. Focusing on the computational method, we recognize that the mesh resolution must be relatively fine in regions where failure is expected and relatively coarse elsewhere. Furthermore, in some modeling approaches the topology in the structural model is different than that required in the fine scale model where failure is to be predicted. This necessarily precludes approaches such as h-adaptivity. We are therefore led to consider multiscale approaches to solve these problems.This work describes an approach to solve multiple (a reference scale and fine scale) coupled boundary value problems for the purpose of nonlinear quasistatic stress analysis. Two examples are included: one example illustrates the multiscale solution strategy to perform quasistatic stress analysis and the other demonstrates the computational beginnings of the ability to model material failure. © 2005 Elsevier B.V. All rights reserved.

Abstract not provided.

Abstract not provided.

Abstract not provided.

One critical aspect of any denuclearization of the Democratic People’s Republic of Korea (DPRK) involves dismantlement of its nuclear facilities and management of their associated radioactive wastes. The decommissioning problem for its two principal operational plutonium facilities at Yongbyun, the 5MWe nuclear reactor and the Radiochemical Laboratory reprocessing facility, alone present a formidable challenge. Dismantling those facilities will create radioactive waste in addition to existing inventories of spent fuel and reprocessing wastes. Negotiations with the DPRK, such as the Six Party Talks, need to appreciate the enormous scale of the radioactive waste management problem resulting from dismantlement. The two operating plutonium facilities, along with their legacy wastes, will result in anywhere from 50 to 100 metric tons of uranium spent fuel, as much as 500,000 liters of liquid high-level waste, as well as miscellaneous high-level waste sources from the Radiochemical Laboratory. A substantial quantity of intermediate-level waste will result from disposing 600 metric tons of graphite from the reactor, an undetermined quantity of chemical decladding liquid waste from reprocessing, and hundreds of tons of contaminated concrete and metal from facility dismantlement. Various facilities for dismantlement, decontamination, waste treatment and packaging, and storage will be needed. The shipment of spent fuel and liquid high level waste out of the DPRK is also likely to be required. Nuclear facility dismantlement and radioactive waste management in the DPRK are all the more difficult because of nuclear nonproliferation constraints, including the call by the United States for “complete, verifiable and irreversible dismantlement,” or “CVID.” It is desirable to accomplish dismantlement quickly, but many aspects of the radioactive waste management cannot be achieved without careful assessment, planning and preparation, sustained commitment, and long completion times. The radioactive waste management problem in fact offers a prospect for international participation to engage the DPRK constructively. DPRK nuclear dismantlement, when accompanied with a concerted effort for effective radioactive waste management, can be a mutually beneficial goal.

Time domain reflectometry (TDR) operates by propagating a radar frequency electromagnetic pulse down a transmission line while monitoring the reflected signal. As the electromagnetic pulse propagates along the transmission line, it is subject to impedance by the dielectric properties of the media along the transmission line (e.g., air, water, and sediment), reflection at dielectric discontinuities (e.g., air-water or water-sediment interface), and attenuation by electrically conductive materials (e.g., salts and clays). Taken together, these characteristics provide a basis for integrated stream monitoring, specifically, concurrent measurement of stream stage, channel profile, and aqueous conductivity. Requisite for such application is a means of extracting the desired stream parameters from measured TDR traces. Analysis is complicated by the fact that interface location and aqueous conductivity vary concurrently and multiple interfaces may be present at any time. For this reason a physically based multisection model employing the S11 scatter function and Debeye parameters for dielectric dispersion and loss is used to analyze acquired TDR traces. Here we explore the capability of this multisection modeling approach for interpreting TDR data acquired from complex environments, such as encountered in stream monitoring. A series of laboratory tank experiments was performed in which the depth of water, depth of sediment, and conductivity were varied systematically. Comparisons between modeled and independently measured data indicate that TDR measurements can be made with an accuracy of ±3.4 × 10-3 m for sensing the location of an air-water or water-sediment interface and ±7.4% of actual for the aqueous conductivity.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The thrust from a multi-cycle, pulse detonation engine operating at practical flight altitudes will vary with the surrounding environment pressure. We have carried out the first experimental study using a detonation tube hung in a ballistic pendulum arrangement within a large pressure vessel in order to determine the effect that the environment has on the single-cycle impulse. The air pressure inside the vessel surrounding the detonation tube varied between 100 and 1.4 kPa while the initial pressure of the stoichiometric ethylene-oxygen mixture inside the tube varied between 100 and 30 kPa. The original impulse model (Wintenberger et al., Journal of Propulsion and Power, Vol. 19, No. 1, 2002) was modified to predict the observed increase in impulse and blow down time as the environment pressure decreased below one atmosphere. Comparisons between the impulse from detonation tubes and ideal, steady flow rockets indicate incomplete expansion of the detonation tube exhaust, resulting in a 37% difference in impulse at a pressure ratio (ratio of pressure behind the Taylor wave to the environment pressure) of 100.