Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

This presentation describes a new effort to better understand insulator flashover in high current, high voltage pulsed power systems. Both experimental and modeling investigations are described. Particular emphasis is put upon understand flashover that initiate in the anode triple junction (anode-vacuum-dielectric).

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This report describes the high-level accomplishments from the Plasma Science and Engineering Grand Challenge LDRD at Sandia National Laboratories. The Laboratory has a need to demonstrate predictive capabilities to model plasma phenomena in order to rapidly accelerate engineering development in several mission areas. The purpose of this Grand Challenge LDRD was to advance the fundamental models, methods, and algorithms along with supporting electrode science foundation to enable a revolutionary shift towards predictive plasma engineering design principles. This project integrated the SNL knowledge base in computer science, plasma physics, materials science, applied mathematics, and relevant application engineering to establish new cross-laboratory collaborations on these topics. As an initial exemplar, this project focused efforts on improving multi-scale modeling capabilities that are utilized to predict the electrical power delivery on large-scale pulsed power accelerators. Specifically, this LDRD was structured into three primary research thrusts that, when integrated, enable complex simulations of these devices: (1) the exploration of multi-scale models describing the desorption of contaminants from pulsed power electrodes, (2) the development of improved algorithms and code technologies to treat the multi-physics phenomena required to predict device performance, and (3) the creation of a rigorous verification and validation infrastructure to evaluate the codes and models across a range of challenge problems. These components were integrated into initial demonstrations of the largest simulations of multi-level vacuum power flow completed to-date, executed on the leading HPC computing machines available in the NNSA complex today. These preliminary studies indicate relevant pulsed power engineering design simulations can now be completed in (of order) several days, a significant improvement over pre-LDRD levels of performance.

Severe acute respiratory syndrome coronavirus 2 (SARS-COV-2) can be spread through close contact or through fomite mediated transmission. This study details the fabrication and analysis of a photocatalyst surface which can rapidly inactivate SARS-COV-2 to limit spread of the virus by fomite mediated transmission. The surface being developed at Sandia for this purpose is a minimally hazardous Ag-Ti0 ₂ nanomaterial which is engineered to have high photocatalytic activity. Initial results at Sandia California in a BSL-2 safe surrogate virus- Vesicular Stomatitis Virus (VSV) show a significant difference between the photocatalyst material under exposure to visible light than controls. Additionally, UV-A light (365 nm) was found to eliminate SARS-COV-2 after 9 hours on all tested surfaces with irradiance of 15 mW/cm ² equivalent to direct circumsolar irradiance.

We show here that Sandia's ALEGRA software can be used to model a permanent magnet in 2D and 3D, with accuracy matching that of the open-source commercial software FEMM. This is done by conducting simulations and experimental measurements for a commercial-grade N42 neodymium alloy ring magnet with a measured magnetic field strength of approximately 0.4 T in its immediate vicinity. Transient simulations using ALEGRA and static simulations using FEMM are conducted. Comparisons are made between simulations and measurements, and amongst the simulations, for sample locations in the steady-state magnetic field. The comparisons show that all models capture the data to within 7%. The FEMM and ALEGRA results agree to within approximately 2%. The most accurate solutions in ALEGRA are obtained using quadrilateral or hexahedral elements. In the case where iron shielding disks are included in the magnetized space, ALEGRA simulations are considerably more expensive because of the increased magnetic diffusion time, but FEMM and ALEGRA results are still in agreement. The magnetic field data are portable to other software interfaces using the Exodus file format.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Next generation pulsed power (NGPP) machines and accelerators require a better understanding of the materials used within the vacuum vessels to achieve lower base pressures (P << 10-5 Torr) and reduce the overall contaminant inventory while incorporating various dielectric materials which tend to be unfavorable for ultra-high vacuum (UHV) applications. By improving the baseline vacuum, it may be possible to delay the onset of impedance collapse, reduce current loss on multi-mega Amp devices, or improve the lifetime of thermionic cathodes, etc [3]. In this study, we examine the vacuum outgassing rate of Rexolite® (cross-linked polystyrene) and Kel-F® (polychlorotrifluoroethylene) as candidate materials for vacuum insulators [1]. These values are then incorporated into boundary conditions for molecular flow simulations using COMSOL Multiphysics® and used to predict the performance of a prototypical pulsed power system designed for 10-8 Torr operations.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.