Publications

Abstract not provided.

We present a materials study of AlGaInP grown on GaAs leveraging deep-level optical spectroscopy and time resolved photoluminescence. Our materials may serve as the basis for wide-bandgap analogs of silicon photomultipliers optimized for short wavelength sensing.

Photocathodes based on GaAs and other III-V semiconductors are capable of producing highly spin-polarized electron beams. GaAs/GaAsP superlattice photocathodes exhibit high spin polarization; however, the quantum efficiency (QE) is limited to 1% or less. To increase the QE, we fabricated a GaAs/GaAsP superlattice photocathode with a Distributed Bragg Reflector (DBR) underneath. This configuration creates a Fabry-Pérot cavity between the DBR and GaAs surface, which enhances the absorption of incident light and, consequently, the QE. These photocathode structures were grown using molecular beam epitaxy and achieved record quantum efficiencies exceeding 15% and electron spin polarization of about 75% when illuminated with near-bandgap photon energies.

Here, the effects of gamma and proton irradiation, and of forward bias minority carrier injection, on photo-response were investigated for InAsSb/AlAsSb pBn mid-wave infrared (MWIR) detectors with an engineered majority-carrier barrier. Room-temperature gamma irradiation had an insignificant effect on 77 K photo-response. Gamma irradiation at 77 K detector temperature, however, decreased in situ photo-response by 19% after a cumulative dose of ~ 500 krad(Si). Subsequent forward bias minority carrier injection had no effect on photo-response. The 77 K detectors irradiated with 30 MeV protons up to 2 Mrad(Si) had photo-response degraded by up to 70%, but here forward bias minority carrier (hole) injection caused up to 12% recovery that persisted more than 30 min. These results suggest a mitigation strategy for maintaining the photo-response of similar detectors in radiation environments that cause displacement damage defects.

Abstract not provided.

We demonstrate a monolithic all-epitaxial resonant-cavity architecture for long-wave infrared photodetectors with substrate-side illumination. An nBn detector with an ultra-thin (t ≈ 350 nm) absorber layer is integrated into a leaky resonant cavity, formed using semi-transparent highly doped (n + +) epitaxial layers, and aligned to the anti-node of the cavity's standing wave. The devices are characterized electrically and optically and demonstrate an external quantum efficiency of ∼25% at T = 180 K in an architecture compatible with focal plane array configurations.

We report on a two-step technique for post-bond III-V substrate removal involving precision mechanical milling and selective chemical etching. We show results on GaAs, GaSb, InP, and InAs substrates and from mm-scale chips to wafers.

We report on a two-step technique for post-bond III-V substrate removal involving precision mechanical milling and selective chemical etching. We show results on GaAs, GaSb, InP, and InAs substrates and from mm-scale chips to wafers.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

InAs-based interband cascade lasers (ICLs) can be more easily adapted toward long wavelength operation than their GaSb counterparts. Devices made from two recent ICL wafers with an advanced waveguide structure are reported, which demonstrate improved device performance in terms of reduced threshold current densities for ICLs near 11 μm or extended operating wavelength beyond 13 μm. The ICLs near 11 μm yielded a significantly reduced continuous wave (cw) lasing threshold of 23 A/cm2 at 80 K with substantially increased cw output power, compared with previously reported ICLs at similar wavelengths. ICLs made from the second wafer incorporated an innovative quantum well active region, comprised of InAsP layers, and lased in the pulsed-mode up to 120 K at 13.2 μm, which is the longest wavelength achieved for III-V interband lasers.

Enhancing the efficiency of second-harmonic generation using all-dielectric metasurfaces to date has mostly focused on electromagnetic engineering of optical modes in the meta-atom. Further advances in nonlinear conversion efficiencies can be gained by engineering the material nonlinearities at the nanoscale, however this cannot be achieved using conventional materials. Semiconductor heterostructures that support resonant nonlinearities using quantum engineered intersubband transitions can provide this new degree of freedom. By simultaneously optimizing the heterostructures and meta-atoms, we experimentally realize an all-dielectric polaritonic metasurface with a maximum second-harmonic generation power conversion factor of 0.5 mW/W2 and power conversion efficiencies of 0.015% at nominal pump intensities of 11 kW/cm2. These conversion efficiencies are higher than the record values reported to date in all-dielectric nonlinear metasurfaces but with 3 orders of magnitude lower pump power. Our results therefore open a new direction for designing efficient nonlinear all-dielectric metasurfaces for new classical and quantum light sources.

Effects of gamma and proton irradiation, and of forward bias minority carrier injection, on minority carrier diffusion and photoresponse were investigated for long-wave (LW) and mid-wave (MW) infrared detectors with engineered majoritycarrier barriers. The LWIR detector was a type-II GaSb/InAs strained-layer superlattice pBiBn structure. The MWIR detector was a InAsSb/AlAsSb nBp structure without superlattices. Room temperature gamma irradiations degraded the minority carrier diffusion length of the LWIR structure, and minority carrier injections caused dramatic improvements, though there was little effect from either treatment on photoresponse. For the MWIR detector, effects of room temperature gamma irradiation and injection on minority carrier diffusion and photoresponse were negligible. Subsequently, both types of detectors were subjected to gamma irradiation at 77 K. In-situ photoresponse was unchanged for the LWIR detectors, while that for the MWIR ones decreased 19% after cumulative dose of ~500 krad(Si). Minority carrier injection had no effect on photoresponse for either. The LWIR detector was then subjected to 4 Mrad(Si) of 30 MeV proton irradiation at 77 K, and showed a 35% decrease in photoresponse, but again no effect from forward bias injection. These results suggest that photoresponse of the LWIR detectors is not limited by minority carrier diffusion.

Abstract not provided.

We discuss thinned InAsSb resonant infrared detectors that are designed to enable high quantum efficiency by using interleaved nanoantennas to read out two wavelengths from each pixel simultaneously.

Abstract not provided.

Abstract not provided.

Gallium is incorporated into the strain-balanced In(Ga)As/InAsSb superlattice system to achieve the same mid-wave infrared cutoff tunability as conventional Ga-free InAs/InAsSb type-II superlattices, but with an additional degree of design freedom to enable optimization of absorption and transport properties. Time-resolved photoluminescence measurements of InGaAs/InAsSb superlattice characterization- and doped device structures are reported from 77 to 300 K and compared to InAs/InAsSb. The low-injection photoluminescence decay yields the minority carrier lifetime, which is analyzed with a recombination rate model, enabling the determination of the temperature-dependent Shockley-Read-Hall, radiative, and Auger recombination lifetimes and extraction of defect energy levels and capture cross section defect concentration products. The Shockley-Read-Hall-limited lifetime of undoped InGaAs/InAsSb is marginally reduced from 2.3 to 1.4 μs due to the inclusion of Ga; however, given that Ga improves the vertical hole mobility by a factor of >10×, a diffusion-limited InGaAs/InAsSb superlattice nBn could expect a lower bound of 2.5× improvement in diffusion length with significant impact on photodetector quantum efficiency and radiation hardness. At temperatures below 120 K, the doped device structures are Shockley-Read-Hall limited at 0.5 μs, which shows promise for detector applications.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Mie-resonant dielectric metasurfaces are excellent candidates for both fundamental studies related to light-matter interactions and for numerous applications ranging from holography to sensing to nonlinear optics. To date, however, most applications using Mie metasurfaces utilize only weak light-matter interaction. Here, we go beyond the weak coupling regime and demonstrate for the first time strong polaritonic coupling between Mie photonic modes and intersubband (ISB) transitions in semiconductor heterostructures. Furthermore, along with demonstrating ISB polaritons with Rabi splitting as large as 10%, we also demonstrate the ability to tailor the strength of strong coupling by engineering either the semiconductor heterostructure or the photonic mode of the resonators. Unlike previous plasmonic-based works, our new all-dielectric metasurface approach to generate ISB polaritons is free from ohmic losses and has high optical damage thresholds, thereby making it ideal for creating novel and compact mid-infrared light sources based on nonlinear optics.

Quantum well intersubband polaritons are traditionally studied in large scale ensembles, over many wavelengths in size.In this presentation, we demonstrate that it is possible to detect and investigate intersubband polaritons in a single sub-wavelength nanoantenna in the IR frequency range. We observe polariton formation using a scattering-type near-fieldmicroscope and nano-FTIR spectroscopy. In this work, we will discuss near-field spectroscopic signatures of plasmonic antennae withand without coupling to the intersubband transition in quantum wells located underneath the antenna. Evanescent fieldamplitude spectra recorded on the antenna surface show a mode anti-crossing behavior in the strong coupling case. Wealso observe a corresponding strong-coupling signature in the phase of the detected field. We anticipate that this near-fieldapproach will enable explorations of strong and ultrastrong light-matter coupling in the single nanoantenna regime,including investigations of the elusive effect of ISB polariton condensation.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Here, the design, fabrication, and characterization of an actively tunable long-wave infrared detector, made possible through direct integration of a graphene-enabled metasurface with a conventional type-II superlattice infrared detector, are reported. This structure allows for post-fabrication tuning of the detector spectral response through voltage-induced modification of the carrier density within graphene and, therefore, its plasmonic response. These changes modify the transmittance through the metasurface, which is fabricated monolithically atop the detector, allowing for spectral control of light reaching the detector. Importantly, this structure provides a fabrication-controlled alignment of the metasurface filter to the detector pixel and is entirely solid-state. Using single pixel devices, relative changes in the spectral response exceeding 8% have been realized. These proof-of-concept devices present a path toward solid-state hyperspectral imaging with independent pixel-to-pixel spectral control through a voltage-actuated dynamic response.

Here, we present a method of determining the background doping type in semiconductors using capacitance-voltage measurements on overetched double mesa p-i-n or n-i-p structures. Unlike Hall measurements, this method is not limited by the conductivity of the substrate. By measuring the capacitance of devices with varying top and bottom mesa sizes, we were able to conclusively determine which mesa contained the p-n junction, revealing the polarity of the intrinsic layer. This method, when demonstrated on GaSb p-i-n and n-i-p structures, determined that the material is residually doped p-type, which is well established by other sources. The method was then applied on a 10 monolayer InAs/10 monolayer AlSb superlattice, for which the doping polarity was unknown, and indicated that this material is also p-type.

The Lorentz-like effective medium resonance (LEMR) exhibited by the longitudinal effective permittivity of semiconductor hyperbolic metamaterials (SHMs) has been known for some time. However, direct observation of this resonance proved to be difficult. Herein, we experimentally demonstrate its existence by strongly coupling SHMs to plasmonic metasurfaces. We consider four strong coupling implementations of SHMs that exhibit different LEMR absorption profiles (both in frequency and in strength) to validate our approach.

We present a method of determining the background doping type in semiconductors using capacitance-voltage measurements on overetched double mesa p-i-n or n-i-p structures. Unlike Hall measurements, this method is not limited by the conductivity of the substrate. By measuring the capacitance of devices with varying top and bottom mesa sizes, we were able to conclusively determine which mesa contained the p-n junction, revealing the polarity of the intrinsic layer. This method, when demonstrated on GaSb p-i-n and n-i-p structures, concluded that the material is residually doped p-type, which is well established by other sources. The method was then applied to a 10 monolayer InAs/10 monolayer AlSb superlattice, for which the doping polarity was unknown, and indicated that this material is also p-type.

An InGaAs/GaAsSb Type-II superlattice is explored as an absorber material for extended short-wave infrared detection. A 10.5 nm period was grown with an InGaAs/GaAsSb thickness ratio of 2 with a target In composition of 46% and target Sb composition of 62%. Cutoff wavelengths near 2.8 μm were achieved with responsivity beyond 3 μm. Demonstrated dark current densities were as low as 1.4 mA/cm2 at 295K and 13 μA/cm2 at 235K at -1V bias. A significant barrier to hole extraction was identified in the detector design that severely limited the external quantum efficiency (EQE) of the detectors. A redesign of the detector that removes that barrier could make InGaAs/GaAsSb very competitive with current commercial HgCdTe and extended InGaAs technology.

We present a method of determining the background doping type in semiconductors using capacitance-voltage measurements on overetched double mesa p-i-n or n-i-p structures. Unlike Hall measurements, this method is not limited by the conductivity of the substrate. By measuring the capacitance of devices with varying top and bottom mesa sizes, we were able to conclusively determine which mesa contained the p-n junction, revealing the polarity of the intrinsic layer. This method, when demonstrated on GaSb p-i-n and n-i-p structures, determined that the material is residually doped p-type, which is well established by other sources. The method was then applied on a 10 monolayer InAs/10 monolayer AlSb superlattice, for which the doping polarity was unknown, and indicated that this material is also p-type.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Characterization of vertical transport in semiconductor heterostructures is extremely difficult and often impractical. Measurements that are relatively straight forward in lateral transport using Hall methods, such as quantifying carrier density or mobility, have no analog in conventional vertical devices. Doppler charge velocimetry may provide an alternative approach to obtaining transport information. We hypothesize that we can drive vertical currents in structures like heterojunction bipolar transistors or nBn detectors, illuminate them with microwaves, and directly measure the carrier velocities through Doppler shifts imparted on the reflected microwave signal. Some challenges involve providing optical injection and working in the vertical geometry required to extract the desired information. While progress was made to this end, experiments have not yet proved successful. Implications for infrared material characterization are summarized at the end of this document.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Strong coupling of an intersubband (ISB) electron transition in quantum wells to a subwavelength plasmonic nanoantenna can give rise to intriguing quantum phenomena, such as ISB polariton condensation, and enable practical devices including low threshold lasers. However, experimental observation of ISB polaritons in an isolated subwavelength system has not yet been reported. Here, we use scanning probe near-field microscopy and Fourier-transform infrared (FTIR) spectroscopy to detect formation of ISB polariton states in a single nanoantenna. We excite the nanoantenna by a broadband IR pulse and spectrally analyze evanescent fields on the nanoantenna surface. We observe the distinctive splitting of the nanoantenna resonance peak into two polariton modes and two ?-phase steps corresponding to each of the modes. We map ISB polariton dispersion using a set of nanoantennae of different sizes. This nano-FTIR spectroscopy approach opens doors for investigations of ISB polariton physics in the single subwavelength nanoantenna regime.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We study semiconductor hyperbolic metamaterials (SHMs) at the quantum limit experimentally using spectroscopic ellipsometry as well as theoretically using a new microscopic theory. The theory is a combination of microscopic density matrix approach for the material response and Green’s function approach for the propagating electric field. Our approach predicts absorptivity of the full multilayer system and for the first time allows the prediction of in-plane and out-of-plane dielectric functions for every individual layer constructing the SHM as well as effective dielectric functions that can be used to describe a homogenized SHM.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Considering the power constrained scaling of silicon complementary metal-oxide-semiconductor technology, the use of high mobility III-V compound semiconductors such as In0.53Ga0.47As in conjunction with high-κ dielectrics is becoming a promising option for future n-type metal-oxide-semiconductor field-effect-transistors. Development of low dissipation field-effect tunable III-V based photonic devices integrated with high-κ dielectrics is therefore very appealing from a technological perspective. In this work, we present an experimental realization of a monolithically integrable, field-effect-tunable, III-V hybrid metasurface operating at long-wave-infrared spectral bands. Our device relies on strong light-matter coupling between epsilon-near-zero (ENZ) modes of an ultra-thin In0.53Ga0.47As layer and the dipole resonances of a complementary plasmonic metasurface. The tuning mechanism of our device is based on field-effect modulation, where we modulate the coupling between the ENZ mode and the metasurface by modifying the carrier density in the ENZ layer using an external bias voltage. Modulating the bias voltage between ±2 V, we deplete and accumulate carriers in the ENZ layer, which result in spectrally tuning the eigenfrequency of the upper polariton branch at 13 μm by 480 nm and modulating the reflectance by 15%, all with leakage current densities less than 1 μA/cm2. Our wavelength scalable approach demonstrates the possibility of designing on-chip voltage-tunable filters compatible with III-V based focal plane arrays at mid- and long-wave-infrared wavelengths.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We report here our recent electron transport results in spatially separated two-dimensional electron and hole gases with nominally degenerate energy subbands, realized in an InAs(10 nm)/GaSb(5 nm) coupled quantum well. We observe a narrow and intense maximum (∼500 kΩ) in the four-terminal resistivity in the charge neutrality region, separating the electron-like and hole-like regimes, with a strong activated temperature dependence above T = 7 K and perfect stability against quantizing magnetic fields. We discuss several mechanisms for that unexpectedly large resistance in this zero-gap semi-metal system including the formation of an excitonic insulator state.

We show that Sb substitution for As in a MBE grown InAs/InAsSb strained layer superlattice (SLS) is accompanied by significant strain fluctuations. The SLS was observed using scanning transmission electron microscopy along the [100] zone axis where the cation and anion atomic columns are separately resolved. Strain analysis based on atomic column positions reveals asymmetrical transitions in the strain profile across the SLS interfaces. The averaged strain profile is quantitatively fitted to the segregation model, which yields a distribution of Sb in agreement with the scanning tunneling microscopy result. The subtraction of the calculated strain reveals an increase in strain fluctuations with the Sb concentration, as well as isolated regions with large strain deviations extending spatially over ∼1 nm, which suggest the presence of point defects.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The InAs/InAs_1-x Sb_x superlattice system distinctly differs from two well-studied superlattice systems GaAs/AlAs and InAs/GaSb in terms of electronic band alignment, common elements at the interface, and phonon spectrum overlapping of the constituents. This fact leads to the unique electronic and vibrational properties of the InAs/InAs_1-xSb_x system when compared to the other two systems. Here in this work, we report a polarized Raman study of the vibrational properties of the InAs/InAs_1-x Sb_x superlattices (SLs) as well as selected InAs_1-xSb_x alloys, all grown on GaSb substrates by either MBE or metalorganic chemical vapor deposition (MOCVD) from both the growth surface and cleaved edge. In the SL, from the (001) backscattering geometry, an InAs-like longitudinal optical (LO) mode is observed as the primary feature, and its intensity is found to increase with increasing Sb composition. From the (110) cleaved-edge backscattering geometry, an InAs-like transverse optical (TO) mode is observed as the main feature in two cross-polarization configurations, but an additional InAs-like “forbidden” LO mode is observed in two parallel-polarization configurations. The InAs_1-xSb_x alloys lattice matched to the substrate ( x_Sb ~ 0.09) grown by MBE are also found to exhibit the forbidden LO mode, implying the existence of some unexpected [001] modulation. However, the strained samples (x_Sb~ 0.35) grown by MOCVD are found to behave like a disordered alloy. The primary conclusions are (1) the InAs-like LO or TO mode can be either a confined or quasiconfined mode in the InAs layers of the SL or extended mode of the whole structure depending on the Sb composition. (2) InAs/InAs_1-xSb_x and InAs/GaSb SLs exhibit significantly different behaviors in the cleaved-edge geometry but qualitatively similar in the (001) geometry. (3) The appearance of the forbidden LO-like mode is a universal signature for SLs and bulk systems resulting from the mixing of phonon modes due to structural modulation or symmetry reduction.

We report on the characterization of narrow-bandgap (Eg ≈ 0.4 eV, at 300 K) interband cascade thermophotovoltaic (TPV) devices with InAs/GaSb/AlSb type-II superlattice absorbers. Two device structures with different numbers of stages (two and three) were designed and grown to study the influence of the number of stages and absorber thicknesses on the device performance at high temperatures (300-340 K). Maximum power efficiencies of 9.6% and 6.5% with open-circuit voltages of 800 and 530 mV were achieved in the three- and two-stage devices at 300 K, respectively. These results validate the benefits of a multiple-stage architecture with thin individual absorbers for efficient conversion of infrared radiation into electricity from low-temperature heat sources. Additionally, we developed an effective characterization method, based on an adapted version of Suns-Voc technique, to extract the device series and shunt resistance in these TPV cells.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We examined the spectral responsivity of a 1.77 μm thick type-II superlattice based long-wave infrared detector in combination with metallic nanoantennas. Coupling between the Fabry-Pérot cavity formed by the semiconductor layer and the resonant nanoantennas on its surface enables spectral selectivity, while also increasing peak quantum efficiency to over 50%. Electromagnetic simulations reveal that this high responsivity is a direct result of field-enhancement in the absorber layer, enabling significant absorption in spite of the absorber's subwavelength thickness. Notably, thinning of the absorbing material could ultimately yield lower photodetector noise through a reduction in dark current while improving photocarrier collection efficiency. The temperature- and incident-angle-independent spectral response observed in these devices allows for operation over a wide range of temperatures and optical systems. This detector paradigm demonstrates potential benefits to device performance with applications throughout the infrared.

Abstract not provided.

The development of novel thermal sources that control the emission spectrum and the angular emission pattern is of fundamental importance. In this paper, we investigate the thermal emission properties of semiconductor hyperbolic metamaterials (SHMs). Our structure does not require the use of any periodic corrugation to provide monochromatic and directional emission properties. We show that these properties arise because of epsilon-near-zero conditions in SHMs. The thermal emission is dominated by the epsilon-near-zero effect in the doped quantum wells composing the SHM. Furthermore, different properties are observed for s and p polarizations, following the characteristics of the strong anisotropy of hyperbolic metamaterials.

Abstract not provided.

A set of seven InAs/InAsSb type-II superlattices (T2SLs) were designed to have speci c bandgap energies between 290 meV (4.3 m) and 135 meV (9.2 m) in order to study the e ects of the T2SL bandgap energy on the minority carrier lifetime. A temperature dependent optical pump-probe technique is used to measure the carrier lifetimes, and the e ect of a mid-gap defect level on the carrier recombination dynamics is reported. The Shockley-Read-Hall (SRH) defect state is found to be at energy of approximately -250 12 meV relative to the valence band edge of bulk GaSb for the entire set of T2SL structures, even though the T2SL valence band edge shifts by 155 meV on the same scale. These results indicate that the SRH defect state in InAs/InAsSb T2SLs is singular and is nearly independent of the exact position of the T2SL bandgap or band edge energies. They also suggest the possibility of engineering the T2SL structure such that the SRH state is removed completely from the bandgap, a result that should signi cantly increase the minority carrier lifetime.

Flip-chip heterogeneously integrated n-p-n InGaP/GaAs heterojunction bipolar transistors (HBTs) with integrated thermal management on wide-bandgap AlN substrates followed by GaAs substrate removal are demonstrated. Without thermal management, substrate removal after integration significantly aggravates self-heating effects, causing poor $I$-$V$ characteristics due to excessive device self-heating. An electrothermal codesign scheme is demonstrated that involves simulation (design), thermal characterization, fabrication, and evaluation. Thermoreflectance thermal imaging, electrical-temperature sensitive parameter-based thermometry, and infrared thermography were utilized to assess the junction temperature rise in HBTs under diverse configurations. In order to reduce the thermal resistance of integrated devices, passive cooling schemes assisted by structural modification, i.e., positioning indium bump heat sinks between the devices and the carrier, were employed. By implementing thermal heat sinks in close proximity to the active region of flip-chip integrated HBTs, the junction-to-baseplate thermal resistance was reduced over a factor of two, as revealed by junction temperature measurements and improvement of electrical performance. The suggested heterogeneous integration method accounts for not only electrical but also thermal requirements providing insight into realization of advanced and robust III-V/Si heterogeneously integrated electronics.

Abstract not provided.

Abstract not provided.

Abstract not provided.

High temperature operation (250-340 K) of short-wavelength interband cascade infrared photodetectors (ICIPs) with InAs/GaSb/Al0.2In0.8Sb/GaSb superlattice absorbers has been demonstrated with a 50% cutoff wavelength of 2.9 μm at 300 K. Two ICIP structures, one with two and the other with three stages, were designed and grown to explore this multiple-stage architecture. At λ = 2.1 μm, the two- and three-stage ICIPs had Johnson-noise-limited detectivities of 5.1 × 109 and 5.8 × 109cm Hz1/2/W, respectively, at 300 K. The better device performance of the three-stage ICIP over the two-stage ICIP confirmed the advantage of more stages for this cascade architecture. An Arrhenius activation energy of 450 meV is extracted for the bulk resistance-area product, which indicates the dominance of the diffusion current at these high temperatures.

We investigate high-temperature and high-frequency operation of interband cascade infrared photodetectors (ICIPs)-two critical properties. Short-wavelength ICIPs with a cutoff wavelength of 2.9 μm had Johnson-noise limited detectivity of 5.8×109 cmHz1/2/W at 300 K, comparable to the commercial Hg1-xCdxTe photodetectors of similar wavelengths. A simple but effective method to estimate the minority carrier diffusion length in short-wavelength ICIPs is introduced. Using this approach, the diffusion length was estimated to be significantly shorter than 1 μm at high temperatures, indicating the importance of a multiple-stage photodetector (e.g., ICIPs) at high temperatures. Recent investigations on the high-frequency operation of mid-wavelength ICIPs (λc=4.3 μm) are discussed. These photodetectors had 3-dB bandwidths up to 1.3 GHz with detectivities exceeding 1x109 cmHz1/2/W at room temperature. These results validate the ability of ICIPs to achieve high bandwidths with large sensitivity and demonstrate the great potential for applications such as: heterodyne detection, and free-space optical communication.

The Auger lifetime is a critical intrinsic parameter for infrared photodetectors as it determines the longest potential minority carrier lifetime and consequently the fundamental limitations to their performance. Here, Auger recombination is characterized in a long-wave infrared InAs/InAsSb type-II superlattice. Auger coefficients as small as 7.1 × 10 - 26 cm6/s are experimentally measured using carrier lifetime data at temperatures in the range of 20 K-80 K. The data are compared to Auger-1 coefficients predicted using a 14-band K · p electronic structure model and to coefficients calculated for HgCdTe of the same bandgap. The experimental superlattice Auger coefficients are found to be an order-of-magnitude smaller than HgCdTe.

Carrier lifetime and dark current measurements are reported for a mid-wavelength infrared InAs0.91Sb0.09 alloy nBn photodetector. Minority carrier lifetimes are measured using a non-contact time-resolved microwave technique on unprocessed portions of the nBn wafer and the Auger recombination Bloch function parameter is determined to be |F1F2|=0.292. The measured lifetimes are also used to calculate the expected diffusion dark current of the nBn devices and are compared with the experimental dark current measured in processed photodetector pixels from the same wafer. Excellent agreement is found between the two, highlighting the important relationship between lifetimes and diffusion currents in nBn photodetectors.

Epsilon-near-zero (ENZ) modes arising from condensed-matter excitations such as phonons and plasmons are a new path for tailoring light-matter interactions at the nanoscale. Complex spectral shaping can be achieved by creating such modes in nanoscale semiconductor layers and controlling their interaction with multiple, distinct, dipole resonant systems. Examples of this behavior are presented at midinfrared frequencies for ENZ modes that are strongly coupled to metamaterial resonators and simultaneously strongly coupled to semiconductor phonons or quantum-well intersubband transitions (ISTs), resulting in double- and triple-polariton branches in transmission spectra. For the double-polariton branch case, we find that the best strategy to maximize the Rabi splitting is to use a combination of a doped layer supporting an ENZ feature and a layer supporting ISTs, with overlapping ENZ and IST frequencies. This design flexibility renders this platform attractive for low-voltage tunable filters, light-emitting diodes, and efficient nonlinear composite materials.

Superconductivity in topological materials has attracted a great deal of interest in both electron physics and material sciences since the theoretical predictions that Majorana fermions can be realized in topological superconductors. Topological superconductivity could be realized in a type II, band-inverted, InAs/GaSb quantum well if it is in proximity to a conventional superconductor. Here, we report observations of the proximity effect induced giant supercurrent states in an InAs/GaSb bilayer system that is sandwiched between two superconducting tantalum electrodes to form a superconductor-InAs/GaSb-superconductor junction. Electron transport results show that the supercurrent states can be preserved in a surprisingly large temperature-magnetic field (T - H) parameter space. In addition, the evolution of differential resistance in T and H reveals an interesting superconducting gap structure.

We present that temperature-dependent measurements of carrier recombination rates using a time-resolved optical pump-probe technique are reported for mid-wave infrared InAs/InAs_1-xSb_x type-2 superlattices (T2SLs). By engineering the layer widths and alloy compositions, a 16 K band-gap of ~235 ± 10 meV was achieved for five unintentionally and four intentionally doped T2SLs. Carrier lifetimes were determined by fitting lifetime models based on Shockley-Read-Hall (SRH), radiative, and Auger recombination processes to the temperature and excess carrier density dependent data. The minority carrier (MC), radiative, and Auger lifetimes were observed to generally increase with increasing antimony content and decreasing layer thickness for the unintentionally doped T2SLs. The MC lifetime is limited by SRH processes at temperatures below 200 K in the unintentionally doped T2SLs. The extracted SRH defect energy levels were found to be near mid-bandgap. Additionally, it is observed that the MC lifetime is limited by Auger recombination in the intentionally doped T2SLs with doping levels greater than n ~10¹⁶ cm^-3.

We use epsilon-near-zero modes in semiconductor nanolayers to design a system whose spectral properties are controlled by their interaction with multi-dipole resonances. This design flexibility renders our platform attractive for efficient nonlinear composite materials.

We have fabricated a superconductor (Ta)-InAs/GaSb bilayer-superconductor (Ta) junction device that has a long mean free path and can preserve the wavelike properties of particles (electrons and holes) inside the junction. Differential conductance measurements were carried out at low temperatures in this device, and McMillan-Rowell like oscillations (MROs) were observed. Surprisingly, a much larger Fermi velocity, compared to that from Shubnikov-de Haas oscillations, was obtained from the frequency of MROs. Possible mechanisms are discussed for this discrepancy.

Abstract not provided.

We use cross-sectional scanning tunneling microscopy (STM) to reconstruct the monolayer-by-monolayer composition profile across a representative subset of MBE-grown InAs/InAsSb superlattice layers and find that antimony segregation frustrates the intended compositional discontinuities across both antimonide-on-arsenide and arsenide-on-antimonide heterojunctions. Graded, rather than abrupt, interfaces are formed in either case. We likewise find that the incorporated antimony per superlattice period varies measurably from beginning to end of the multilayer stack. Although the intended antimony discontinuities predict significant discrepancies with respect to the experimentally observed high-resolution x-ray diffraction spectrum, dynamical simulations based on the STM-derived profiles provide an excellent quantitative match to all important aspects of the x-ray data.

Coherent superposition of light from subwavelength sources is an attractive prospect for the manipulation of the direction, shape and polarization of optical beams. This phenomenon constitutes the basis of phased arrays, commonly used at microwave and radio frequencies. Here we propose a new concept for phased-array sources at infrared frequencies based on metamaterial nanocavities coupled to a highly nonlinear semiconductor heterostructure. Optical pumping of the nanocavity induces a localized, phase-locked, nonlinear resonant polarization that acts as a source feed for a higher-order resonance of the nanocavity. Varying the nanocavity design enables the production of beams with arbitrary shape and polarization. As an example, we demonstrate two second harmonic phased-array sources that perform two optical functions at the second harmonic wavelength (∼5μm): a beam splitter and a polarizing beam splitter. Proper design of the nanocavity and nonlinear heterostructure will enable such phased arrays to span most of the infrared spectrum.

Abstract not provided.

Abstract not provided.

We use epsilon-near-zero modes in semiconductor nanolayers to design a system whose spectral properties are controlled by their interaction with multi-dipole resonances. This design flexibility renders our platform attractive for efficient nonlinear composite materials. © OSA 2015.

Time-resolved measurements of carrier recombination are reported for a midwave infrared InAs/InAs0.66Sb0.34 type-II superlattice (T2SL) as a function of pump intensity and sample temperature. By including the T2SL doping level in the analysis, the Shockley-Read-Hall (SRH), radiative, and Auger recombination components of the carrier lifetime are uniquely distinguished at each temperature. SRH is the limiting recombination mechanism for excess carrier densities less than the doping level (the low-injection regime) and temperatures less than 175 K. A SRH defect energy of 95 meV, either below the T2SL conduction-band edge or above the T2SL valence-band edge, is identified. Auger recombination limits the carrier lifetimes for excess carrier densities greater than the doping level (the high-injection regime) for all temperatures tested. Additionally, at temperatures greater than 225 K, Auger recombination also limits the low-injection carrier lifetime due to the onset of the intrinsic temperature range and large intrinsic carrier densities. Radiative recombination is found to not have a significant contribution to the total lifetime for all temperatures and injection regimes, with the data implying a photon recycling factor of 15. Using the measured lifetime data, diffusion currents are calculated and compared to calculated Hg1-xCdxTe dark current, indicating that the T2SL can have a lower dark current with mitigation of the SRH defect states. These results illustrate the potential for InAs/InAs1-xSbx T2SLs as absorbers in infrared photodetectors.

Metallic nanocavities with deep subwavelength mode volumes can lead to dramatic changes in the behavior of emitters placed in their vicinity. This collocation and interaction often leads to strong coupling. Here, we present for the first time experimental evidence that the Rabi splitting is directly proportional to the electrostatic capacitance associated with the metallic nanocavity. The system analyzed consists of different metamaterial geometries with the same resonance wavelength coupled to intersubband transitions in quantum wells.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The goal of this project is to search for Majorana fermions (a new quantum particle) in a topological superconductor (a new quantum matter achieved in a topological insulator proximitized by an s-wave superconductor). Majorana fermions (MFs) are electron-like particles that are their own anti-particles. MFs are shown to obey non-Abelian statistics and, thus, can be harnessed to make a fault-resistant topological quantum computer. With the arrival of topological insulators, novel schemes to create MFs have been proposed in hybrid systems by combining a topological insulator with a conventional superconductor. In this LDRD project, we will follow the theoretical proposals to search for MFs in one-dimensional (1D) topological superconductors. 1D topological superconductor will be created inside of a quantum point contact (with the metal pinch-off gates made of conventional s-wave superconductors such as niobium) in a two-dimensional topological insulator (such as inverted type-II InAs/GaSb heterostructure).

Abstract not provided.

We utilize the unique dispersion properties of leaky plasmon polaritons in epsilon-near-zero (ENZ) thin films to demonstrate thermal radiation control. Owing to its highly flat dispersion above the light line, a thermally excited leaky wave at the ENZ frequency out-couples into free space without any scattering structures, resulting in a narrowband, wide-angle, p-polarized thermal emission spectrum. We demonstrate this idea by measuring angle- and polarization-resolved thermal emission spectra from a single layer of unpatterned, doped semiconductors with deep-subwavelength film thickness (d / λ 0 ∼ 6 × 10 - 3, where d is the film thickness and λ 0 is the free space wavelength). We show that this semiconductor ENZ film effectively works as a leaky wave thermal radiation antenna, which generates far-field radiation from a thermally excited mode. The use of semiconductors makes the radiation frequency highly tunable by controlling doping densities and also facilitates device integration with other components. Therefore, this leaky plasmon polariton emission from semiconductor ENZ films provides an avenue for on-chip control of thermal radiation.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Wafer-level step-stress experiments on high voltage Npn InGaP/GaAs HBTs are presented. A methodology utilizing brief, monotonically increasing stresses and periodic, interrupted parametric characterization is presented. The method and various examples of step-stressed HBTs illustrate the value of the technique for screening the reliability of HBT wafers. Degradation modes observed in these InGaP/GaAs HBTs closely correspond to a subset of those in other, longer types of reliability experiments and can be relevant in a reliability screen. A statistical sampling of HBT wafers reveals a consistently realized critical destructive limit over a very narrow power range, which indicates that thermal stress is the main cause of degradation. When stepped just shy of the destructive limit, electrical characteristics are capable of revealing gradual degradation. The end state of stressing typically involves shorting of both the base-emitter and base-collector junctions. Interrupted characterization revealed cases where baseemitter shorts preceded base-collector shorts and other cases where base-collector shorts occurred first. Examples of degradation include reductions in reverse breakdown voltage, increases in the offset voltage, and drops in current gain. These wafer-level stepstress techniques show promise for reducing the large time lag between wafer fabrication and useful reliability screening in HBTs.

We present an actively tunable mid-infrared metamaterial operating in the strong lightmatter coupling regime. We can tune the upper polariton branch continuously over 8% of the center frequency by applying 5 V. © 2014 OSA.

We present the design, fabrication, and realization of an electrically tunable metamaterial operating in the mid-infrared spectral range. Our devices combine intersubband transitions in semiconductor quantum-wells with planar metamaterials and operate in the strong light-matter coupling regime. The resonance frequency of the intersubband transition can be controlled by an external bias relative to the fixed metamaterial resonance. This allows us to switch dynamically from an uncoupled to a strongly coupled system and thereby to shift the eigenfrequency of the upper polariton branch by 2.5 THz (corresponding to 8% of the center frequency or one full linewidth) with a bias of 5 V. © 2013 AIP Publishing LLC.

Quantum-engineered multiple stage photovoltaic (PV) devices are explored based on InAs/GaSb/AlSb interband cascade (IC) structures. These ICPV devices employ multiple discrete absorbers that are connected in series by widebandgap unipolar barriers using type-II heterostructure interfaces for facilitating carrier transport between cascade stages similar to IC lasers. The discrete architecture is beneficial for improving the collection efficiency and for spectral splitting by utilizing absorbers with different bandgaps. As such, the photo-voltages from each individual cascade stage in an ICPV device add together, creating a high overall open-circuit voltage, similar to conventional multi-junction tandem solar cells. Furthermore, photo-generated carriers can be collected with nearly 100% efficiency in each stage. This is because the carriers travel over only a single cascade stage, designed to be shorter than a typical diffusion length. The approach is of significant importance for operation at high temperatures where the diffusion length is reduced. Here, we will present our recent progress in the study of ICPV devices, which includes the demonstration of ICPV devices at room temperature and above with narrow bandgaps (e.g. 0.23 eV) and high open-circuit voltages. © (2013) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

InPSb and InAsPSb have been investigated for use as absorber materials in GaSb-based n-type/barrier/n-type (nBn) detectors with cutoff wavelengths shorter than 4.2 μm. The growth temperature window for high-quality InPSb lattice-matched to GaSb by molecular beam epitaxy is approximately 440-460 °C. InPSb films with thicknesses greater than approximately 1 μm or films grown outside this temperature window have high densities of large defects, with films grown at lower temperatures exhibiting evidence of significant phase separation. In contrast, InAsPSb films can be grown with excellent surface morphologies and no apparent phase separation over a wide temperature range. InAsPSb samples with low-temperature photoluminescence between 3.0 and 3.4 μm and lattice mismatch of less than 1 × 10-3 have been grown, although both photoluminescence and x-ray diffraction data exhibit peak splitting indicative of compositional nonuniformity. AlAsSb-barrier nBn detectors with InPSb and InAsPSb absorbers have been fabricated. At 160 K, InPSb-absorber devices have a photocurrent responsivity edge at approximately 2.8 μm and a dark current of approximately 1.4 × 10-7 A/cm2, and InAsPSb devices with responsivity edges of 3.1-3.2 μm have a dark current of 2.3 × 10-8 A/cm2. Both InPSb and InAsPSb devices require significant reverse bias for full photocurrent collection at low temperature, suggesting the existence of an undesirable valence band energy discontinuity. The temperature dependence of dark current indicates that it is dominated by a mechanism other than generation in the undepleted absorber region. © 2013 American Vacuum Society.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We demonstrate the effects of integrating a nanoantenna to a midwave infrared (MWIR) focal plane array (FPA). We model an antenna-coupled photodetector with a nanoantenna fabricated in close proximity to the active material of a photodetector. This proximity allows us to take advantage of the concentrated plasmonic fields of the nanoantenna. The role of the nanoantenna is to convert free-space plane waves into surface plasmons bound to a patterned metal surface. These plasmonic fields are concentrated in a small volume near the metal surface. Field concentration allows for a thinner layer of absorbing material to be used in the photodetector design and promises improvements in cutoff wavelength and dark current (higher operating temperature). While the nanoantenna concept may be applied to any active photodetector material, we chose to integrate the nanoantenna with an InAsSb photodiode. The geometry of the nanoantenna-coupled detector is optimized to give maximal carrier generation in the active region of the photodiode, and fabrication processes must be altered to accommodate the nanoantenna structure. The intensity profiles and the carrier generation rates in the photodetector active layers are determined by finite element method simulations, and iteration between optical nanoantenna simulation and detector modeling is used to optimize the device structure. © 2012 SPIE.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We have fabricated mid-wave infrared photodetectors containing InAsSb absorber regions and AlAsSb barriers in n-barrier-n (nBn) and n-barrier-p (nBp) configurations, and characterized them by current-voltage, photocurrent, and capacitance-voltage measurements in the 100-200 K temperature range. Efficient collection of photocurrent in the nBn structure requires application of a small reverse bias resulting in a minimum dark current, while the nBp devices have high responsivity at zero bias. When biasing both types of devices for equal dark currents, the nBn structure exhibits a differential resistance significantly higher than the nBp, although the nBp device may be biased for arbitrarily low dark current at the expense of much lower dynamic resistance. Capacitance-voltage measurements allow determination of the electron concentration in the unintentionally-doped absorber material, and demonstrate the existence of an electron accumulation layer at the absorber/barrier interface in the nBn device. Numerical simulations of idealized nBn devices demonstrate that photocurrent collection is possible under conditions of minimal absorber region depletion, thereby strongly suppressing depletion region Shockley-Read-Hall generation. © 2010 Copyright SPIE - The International Society for Optical Engineering.

The experimental characterization of single barrier heterostructure thermionic cooling devices at cryogenic temperatures is reported. The device studied was a cylindrical InGaAs microrefrigerator, in which the active layer was a 1 μm thick In 0.527Al 0.218Ga 0.255As heterostructure barrier with n-type doping concentration of 6.68 × 10 16 cm -3 and an In 0.53Ga 0.47As emitter/collector of 5 × 10 18 cm -3 n-doping. A full field thermoreflectance imaging technique was used to measure the distribution of temperature change on the device's top surface when different current excitation values were applied. By reversing the current direction, we studied the device's behavior in both cooling and heating regimes. At an ambient temperature of 100 K, a maximum cooling of 0.6 K was measured. This value was approximately one-third of the measured maximum cooling value at room temperature (1.8 K). The paper describes the device's structure and the first reported thermal imaging at cryogenic temperatures using the thermoreflectance technique. © 2009 The Author(s).

Microfabrication methods have been applied to the fabrication of wire arrays suitable for use in Z. Self-curling GaAs/AlGaAs supports were fabricated as an initial route to make small wire arrays (4mm diameter). A strain relief structure that could be integrated with the wire was designed to allow displacements of the anode/cathode connections in Z. Electroplated gold wire arrays with integrated anode/cathode bus connections were found to be sufficiently robust to allow direct handling. Platinum and copper plating processes were also investigated. A process to fabricate wire arrays on any substrate with wire thickness up to 35 microns was developed. Methods to handle and mount these arrays were developed. Fabrication of wire arrays of 20mm diameter was demonstrated, and the path to 40mm array fabrication is clear. With some final investment to show array mounting into Z hardware, the entire process to produce a microfabricated wire array will have been demonstrated.

Abstract not provided.

Abstract not provided.

We demonstrate high-speed switching of a symmetric self-electrooptic effect device (S-SEED) operating at 1550 nm. Transitions faster than 10 ps are observed, verifying the suitability of this technology for integrated logic operations beyond 40 GHz. © 2008 Optical Society of America.

Abstract not provided.

Abstract not provided.

Specially designed Pnp heterojunction bipolar transistors (HBT's) in the AlGaAs/GaAs material system can offer improved radiation response over commercially-available silicon bipolar junction transistors (BJT's). To be a viable alternative to the silicon Pnp BJT, improvements to the manufacturability of the HBT were required. Utilization of a Pd/Ge/Au non-spiking ohmic contact to the base and implementation of a PECVD silicon nitride hard mask for wet etch control were the primary developments that led to a more reliable fabrication process. The implementation of the silicon nitride hard mask and the subsequent process improvements increased the average electrical yield from 43% to 90%. © The Electrochemical Society.

The key need that this project has addressed is a short-wave infrared light detector for ranging (LIDAR) imaging at temperatures greater than 100K, as desired by nonproliferation and work for other customers. Several novel device structures to improve avalanche photodiodes (APDs) were fabricated to achieve the desired APD performance. A primary challenge to achieving high sensitivity APDs at 1550 nm is that the small band-gap materials (e.g., InGaAs or Ge) necessary to detect low-energy photons exhibit higher dark counts and higher multiplication noise compared to materials like silicon. To overcome these historical problems APDs were designed and fabricated using separate absorption and multiplication (SAM) regions. The absorption regions used (InGaAs or Ge) to leverage these materials 1550 nm sensitivity. Geiger mode detection was chosen to circumvent gain noise issues in the III-V and Ge multiplication regions, while a novel Ge/Si device was built to examine the utility of transferring photoelectrons in a silicon multiplication region. Silicon is known to have very good analog and GM multiplication properties. The proposed devices represented a high-risk for high-reward approach. Therefore one primary goal of this work was to experimentally resolve uncertainty about the novel APD structures. This work specifically examined three different designs. An InGaAs/InAlAs Geiger mode (GM) structure was proposed for the superior multiplication properties of the InAlAs. The hypothesis to be tested in this structure was whether InAlAs really presented an advantage in GM. A Ge/Si SAM was proposed representing the best possible multiplication material (i.e., silicon), however, significant uncertainty existed about both the Ge material quality and the ability to transfer photoelectrons across the Ge/Si interface. Finally a third pure germanium GM structure was proposed because bulk germanium has been reported to have better dark count properties. However, significant uncertainty existed about the quantum efficiency at 1550 nm the necessary operating temperature. This project has resulted in several conclusions after fabrication and measurement of the proposed structures. We have successfully demonstrated the Ge/Si proof-of-concept in producing high analog gain in a silicon region while absorbing in a Ge region. This has included significant Ge processing infrastructure development at Sandia. However, sensitivity is limited at low temperatures due to high dark currents that we ascribe to tunneling. This leaves remaining uncertainty about whether this structure can achieve the desired performance with further development. GM detection in InGaAs/InAlAs, Ge/Si, Si and pure Ge devices fabricated at Sandia was shown to overcome gain noise challenges, which represents critical learning that will enable Sandia to respond to future single photon detection needs. However, challenges to the operation of these devices in GM remain. The InAlAs multiplication region was not found to be significantly superior to current InP regions for GM, however, improved multiplication region design of InGaAs/InP APDs has been highlighted. For Ge GM detectors it still remains unclear whether an optimal trade-off of parameters can achieve the necessary sensitivity at 1550 nm. To further examine these remaining questions, as well as other application spaces for these technologies, funding for an Intelligence Community post-doc was awarded this year.

Optical lime-domain reflectometry (OTDR) is an effeclive technique for locating faults in fiber communication links. The fact that most OTDR measurements are performed manually is a significant drawback, because it makes them too costly for use in many short-distance networks and too slow for use in military avionic platforms. Here we describe and demonstrate an automated, low-cost, real-time approach to fault monitoring that can be achieved by integrating OTDR functionality directly into VCSEL-based transceivers. This built-in test capability is straightforward to implement and relevant to both multimode and single mode networks. In-situ OTDR uses the transmitter VCSEL already present in data transceivers. Fault monitoring is performed by emitting a brief optical pulse into the fiber and then turning the VCSEL off. If a fault exists, a portion of the optical pulse returns to the transceiver after a time equal to the round-trip delay through the fiber. In multimode OTDR, the signal is detected by an integrated photodetector, while in single mode OTDR the VCSEL itself can be used as a detector. Modified driver electronics perform the measurement and analysis. We demonstrate that VCSEL-based OTDR has sufficient sensitivity to determine the location of most faults commonly seen in short-haul networks (i.e., the Fresnel reflections from improperly terminated fibers and scattering from raggedly-broken fibers). Results are described for single mode and multimode experiments, at both 850 nm and 1.3 μm. We discuss the resolution and sensitivity that have been achieved, as well as expected limitations for this novel approach to network monitoring.

Abstract not provided.

The goal of our project was to examine a novel quantum cascade laser design that should inherently increase the output power of the laser while simultaneously providing a broad tuning range. Such a laser source enables multiple chemical species identification with a single laser and/or very broad frequency coverage with a small number of different lasers, thus reducing the size and cost of laser based chemical detection systems. In our design concept, the discrete states in quantum cascade lasers are replaced by minibands made of multiple closely spaced electron levels. To facilitate the arduous task of designing miniband-to-miniband quantum cascade lasers, we developed a program that works in conjunction with our existing modeling software to completely automate the design process. Laser designs were grown, characterized, and iterated. The details of the automated design program and the measurement results are summarized in this report.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The goal of this LDRD was to investigate III-antimonide/nitride based materials for unique semiconductor properties and applications. Previous to this study, lack of basic information concerning these alloys restricted their use in semiconductor devices. Long wavelength emission on GaAs substrates is of critical importance to telecommunication applications for cost reduction and integration into microsystems. Currently InGaAsN, on a GaAs substrate, is being commercially pursued for the important 1.3 micrometer dispersion minima of silica-glass optical fiber; due, in large part, to previous research at Sandia National Laboratories. However, InGaAsN has not shown great promise for 1.55 micrometer emission which is the low-loss window of single mode optical fiber used in transatlantic fiber. Other important applications for the antimonide/nitride based materials include the base junction of an HBT to reduce the operating voltage which is important for wireless communication links, and for improving the efficiency of a multijunction solar cell. We have undertaken the first comprehensive theoretical, experimental and device study of this material with promising results. Theoretical modeling has identified GaAsSbN to be a similar or potentially superior candidate to InGaAsN for long wavelength emission on GaAs. We have confirmed these predictions by producing emission out to 1.66 micrometers and have achieved edge emitting and VCSEL electroluminescence at 1.3 micrometers. We have also done the first study of the transport properties of this material including mobility, electron/hole mass, and exciton reduced mass. This study has increased the understanding of the III-antimonide/nitride materials enough to warrant consideration for all of the target device applications.

This report describes the research accomplishments achieved under the LDRD Project 'Radiation Hardened Optoelectronic Components for Space-Based Applications.' The aim of this LDRD has been to investigate the radiation hardness of vertical-cavity surface-emitting lasers (VCSELs) and photodiodes by looking at both the effects of total dose and of single-event upsets on the electrical and optical characteristics of VCSELs and photodiodes. These investigations were intended to provide guidance for the eventual integration of radiation hardened VCSELs and photodiodes with rad-hard driver and receiver electronics from an external vendor for space applications. During this one-year project, we have fabricated GaAs-based VCSELs and photodiodes, investigated ionization-induced transient effects due to high-energy protons, and measured the degradation of performance from both high-energy protons and neutrons.

Abstract not provided.

Many MEMS-based components require optical monitoring techniques using optoelectronic devices for converting mechanical position information into useful electronic signals. While the constituent piece-parts of such hybrid opto-MEMS components can be separately optimized, the resulting component performance, size, ruggedness and cost are substantially compromised due to assembly and packaging limitations. GaAs MOEMS offers the possibility of monolithically integrating high-performance optoelectronics with simple mechanical structures built in very low-stress epitaxial layers with a resulting component performance determined only by GaAs microfabrication technology limitations. GaAs MOEMS implicitly integrates the capability for radiation-hardened optical communications into the MEMS sensor or actuator component, a vital step towards rugged integrated autonomous microsystems that sense, act, and communicate. This project establishes a new foundational technology that monolithically combines GaAs optoelectronics with simple mechanics. Critical process issues addressed include selectivity, electrochemical characteristics, and anisotropy of the release chemistry, and post-release drying and coating processes. Several types of devices incorporating this novel technology are demonstrated.

Abstract not provided.

Abstract not provided.

Selectively oxidized vertical cavity lasers emitting at 1294 nm using InGaAsN quantum wells are reported for the first time which operate continuous wave at and above room temperature. The lasers employ two n-type Al{sub 0.94}Ga{sub 0.06}As/GaAs distributed Bragg reflectors each with a selectively oxidized current aperture adjacent to the optical cavity, and the top output mirror contains a tunnel junction to inject holes into the active region. Continuous wave single mode lasing is observed up to 55 C. These lasers exhibit the longest wavelength reported to date for vertical cavity surface emitting lasers grown on GaAs substrates.

In-plane magnetic field photoluminescence spectra from n series of n-type modulation doped GaAs/Al{sub 0.3}Ga{sub 0.7}As coupled double quantum wells show distinctive doublet structures related to the tunnel-split ground sub-level states. The magnetic field behavior of the upper transition from the antisymmetric state strongly depends on sample mobility. In a lower mobility sample, the transition energy displays an N-type kink with field (namely a maximum followed by a minimum), whereas higher mobility samples have a linear dependence. The former is attributed to a coupling mechanism due to homogeneous broadening of the electron and hole states. The results are in good agreement with recent theoretical calculations.

The authors have investigated the properties of GaAsSb/InGaAs type-II bilayer quantum well structures grown by molecule beam epitaxy for use in long-wavelength lasers on GaAs substrates. Structures with layer, strains and thicknesses designed to be thermodynamically stable against dislocation formation exhibit room-temperature photoluminescence at wavelengths as long as 1.43 {mu}m. The photoluminescence emission wavelength is significantly affected by growth temperature and the sequence of layer growth (InGaAs/GaAsSb vs GaAsSb/InGaAs), suggesting that Sb and/or In segregation results in non-ideal interfaces under certain growth conditions. At low injection currents, double heterostructure lasers with GaAsSb/InGaAs bilayer quantum well active regions display electroluminescence at wavelengths comparable to those obtained in photoluminescence, but at higher currents the electroluminescence shifts to shorter wavelengths. Lasers have been obtained with threshold current densities as low as 120 A/cm{sup 2} at 1.17 {mu}m, and 2.1 kA/cm{sup 2} at 1.21 {mu}m.

Strained-layer semiconductor films offer tremendous potential with regards to optoelectronic applications for high speed communications, mobile communications, sensing, and novel logic devices. It is an unfortunate reality that many of the possible film/substrate combinations that could be exploited technologically are off limits because of large differences in lattice parameters, chemical compatibilities, or thermal expansion rates. These mechanical, chemical, and thermal incompatibilities manifest themselves primarily in terms of lattice defects such as dislocations and antiphase boundaries, and in some cases through enhanced surface roughness. An additional limitation, from a production point of view, is money. Device manufacturers as a rule want the cheapest substrate possible. Freeing the heteroepitaxial world of the bonds of (near) lattice matching would vastly expand the types of working devices that could be grown. As a result, a great deal of effort has been expended finding schemes to integrate dissimilar film/substrate materials while preserving the perfection of the film layer. One such scheme receiving significant attention lately is the so-called compliant substrate approach.

The authors report data on GaAsSb single quantum well lasers grown on GaAs substrates. Room temperature pulsed emission at 1.275 {micro}m in a 1,250 {micro}m-long device has been observed. Minimum threshold current densities of 535 A/cm{sup 2} were measured in 2000 {micro}m long lasers. The authors also measured internal losses of 2--5 cm{sup {minus}1}, internal quantum efficiencies of 30-38% and characteristic temperature T{sub 0} of 67--77 C. From these parameters a gain constant G{sub 0} of 1,660 cm{sup {minus}1} and a transparency current density J{sub tr} of 134 A/cm{sup 2} were calculated. The results indicate the potential for fabricating 1.3 {micro}m VCSELs from these materials.

A high voltage GaAs HBT with an open-base collector breakdown voltage of 106 V and an open-emitter breakdown voltage of 134 V has been demonstrated. A high quality 9.0 {micro}m thick collector doped to 2.0{times}10{sup 15} cm{sup {minus}3} grown by MBE on a doped GaAs substrate is the key to achieving this breakdown. These results were achieved for HBTs with 4{times}40 {micro}m{sup 2} emitters. DC current gain of 38 at 6,000 A/cm{sup 2} was measured.

This LDRD project explored the fundamental physics of a new class of photonic materials, photonic bandgap structures (PBG), and examine its unique properties for the design and implementation of photonic devices on a nano-meter length scale for the control and confinement of light. The low loss, highly reflective and quantum interference nature of a PBG material makes it one of the most promising candidates for realizing an extremely high-Q resonant cavity, >10,000, for optoelectronic applications and for the exploration of novel photonic physics, such as photonic localization, tunneling and modification of spontaneous emission rate. Moreover, the photonic bandgap concept affords us with a new opportunity to design and tailor photonic properties in very much the same way we manipulate, or bandgap engineer, electronic properties through modern epitaxy.

Abstract not provided.

Mixed arsenide/antimonide materials have unique properties which make them potentially valuable for use in VCSELs operating at wavelengths longer than 1 {micro}m. The authors present their progress in applying these materials to VCSEL designs for 1--1.55 {micro}m.

Short communication.