In order to study the effects of Ni oxidation barriers on H diffusion in Zr, a Ni-Zr-H potential was developed based on an existing Ni-Zr potential. Using this and existing binary potentials H diffusion characteristics were calculated and some limited findings for the performance of Ni on Zr coatings are made.
This report discusses the progress on the collaboration between Sandia National Laboratories (Sandia) and Japan Atomic Energy Agency (JAEA) on the sodium fire research in fiscal year 2019. First, the current sodium pool fire model in MELCOR, which is adapted from CONTAIN-LMR code, is discussed. The associated sodium fire input requirements are also presented. A proposed model improvement developed at Sandia is discussed. Finally, the validation study of the sodium pool fire model in MELCOR carried out by a JAEA's staff is described. To validate this model, a JAEA sodium pool fire experiment (F7-1 test) is used. A preliminary calculation is performed using a modified MELCOR model from a previous experiment simulation. The results of the calculation are discussed as well as suggestions for improvement. Finally, recommendations are made for new MELCOR simulations for next fiscal year, 2020.
Hetero-Junction Bipolar Transistors (HBT) have several advantages over Silicon Bipolar Junction Transistors (BJT) in radiation environments. One advantage is an intrinsic hardness to displacement damage causing radiation. The generally smaller size of HBTs compared to BJTs also means that less photocurrent is generated by these devices. A disadvantage of the smaller size is less ability to dissipate heat due to smaller surface areas and contacts. This report describes simulations intended to study the initial heating of HBT transistors due to ionizing radiation events and the subsequent heating caused by feedback in the devices when responding to these events.
Determine a feasible method to remove protective plastic coating from steel after CO2 cutting that will enable high through put and reduce man hours spent on removing plastic by hand. Company is open to any and all ideas.
The 2020 Annual Terrestrial Sampling Plan for Sandia National Laboratories/New Mexico on Kirtland Air Force Base has been prepared in accordance with the "Letter of Agreement Between Department of Energy, National Nuclear Security Administration, Sandia Field Office (DOE/NNSA/SFO) and 377th Air Base Wing (ABW), Kirtland Air Force Base (KAFB) for Terrestrial Sampling" (signed January 2017), Sandia National Laboratories, New Mexico (SNL/NM). The Letter of Agreement requires submittal of an annual terrestrial sampling plan.
Atomic clocks are precision timekeeping devices that form the basis for modern communication and navigation. While many atomic clocks are room-sized systems requiring bulky free space optics and detectors, the Trapped-lon Clock using Technology-On-Chip (TICTOC) project integrates these components into Sandia's existing surface trap technology via waveguides for beam delivery and avalanche photodiodes for light detection. Taking advantage of a multi-ensemble clock interrogation approach, we expect to achieve record time stability (< 1 ns error per year) in a compact (< /1 2 L) clock. Here, we present progress on the development of the integrated devices and recent trapped ion demonstrations.
ASTM Committee E10 on Nuclear Technology and Applications develops and maintains many standards that are relevant to the radiation metrology activities in Sandia National Laboratories' Radiation and Electrical Sciences Center. This is particularly true for the reactor facilities and Subcommittee E10.07 on Radiation Dosimetry for Radiation Effects on Materials and Devices. In the past decade, Subcommittee E10.07 has been making substantive changes to the standard widely used to assess radiation hardness to neutron effects in electronics, E722 – Standard Practice for Characterking Neutron Fluence Spectra in Terms of an Equivalent Monoenergetic Neutron Fluence for Radiation-Hardness Testing of Electronics. ASTM Standard E722 describes the method that defines the 1-MeV silicon and the 1-MeV gallium arsenide equivalent fluence radiation damage metrics. An evaluation of the impact of changes to the shape of the 1-MeV silicon equivalent fluence radiation damage metric from the 1985 version (E722-85) to the most recent version (E722-19) is performed.
The New Mexico Small Business Assistance program at Sandia National Labs and Parental Values, LLC have agreed to explore commonly known principles to describe techniques in trilateration. The objective from Parental Values' standpoint is to use these commonly known principles for the purpose of their own software development by their employees. The software would be meant for mobile devices held by minors and the software would be monitored by parent(s) and/or guardians. The software would be able to notify parent(s)/guardian(s) in the event of an active shooter in a proximity close enough for the mobile devices' onboard microphones to detect a gunshot's noise. This document is meant for the employees of Parental Values to understand the commonly known principles as it applies to their intended implementation.
In components with two materials, such as glass-to-metal (GtM) seals, residual stress can reduce long-term reliability. Therefore, it is important to be able to accurately measure residual stress within these components. The residual stress can be from a large strain due to the mismatch of thermo-physical response of the two materials or a small strain due to stress and/or structural relaxation. Both modeling and experimental measurements were conducted on multiple GtM seals constructed with CGI 930 glass with purposely added alumina particles. The alumina particles have an established Cr fluorescence pattern and the shift in position of these peaks can accurately measure the strain of the alumina crystals. Photoluminescence spectroscopy (PLS) technique was utilized due to its non-destructive nature and high spatial resolution. PLS scans of these components were analyzed and compared to the models developed previously.
Accurately predicting power generation for PV sites is critical for prioritizing relevant operations & maintenance activities, thereby extending the lifetime of a system and increasing the amount of revenue generated. Machine learning techniques can help us in this regard by providing more accurate predictions of PV power production, such that the forecasts take into account not only a site's system design characteristics, but also important weather and climate information. This type of research is important because we can leverage the vast amounts of SCADA data we collect to build more effective, accurate models that can help improve our performance management.
Abnormal electrical environments receive a lot of attention from nuclear safety engineers, but less attention has been paid to the magnetic effects that accompany such environments. Engineers with backgrounds outside of physics or electrical engineering may not be as familiar with this topic; this report serves as a brief summary of the phenomena and proposes experiments to support practical engineering solutions. Lightning strikes, in particular, create an environment hazardous to electronics, especially to components that rely on magnetic coupling for normal function. The most direct method of mitigating unwanted magnetic effects caused by lightning is to shield the component of interest; several materials and configuration options are explained here. An experimental approach is recommended to validate numerical modeling.
Sandia has demonstrated its commitment to the small business community through annually increasing small business goals, the 5% New Mexico small business pricing preference, and the newly launched Mentor-Protégé' program. We look forward to continuing to build relationships with small and diverse suppliers to achieve our national security mission and spur economic growth in New Mexico and across the country.
This document provides a "Build Guide" for a Generic Runnable System (GRS) of the Geophysical Monitoring Systems (GMS) common source code. This guide includes a list of software dependencies and licenses, hardware specifications, and instructions for how to build the system from the source code. The document is written for individuals who are experienced as administrators of Linux systems.
Inertial Fusion is being supported by the NNSA for weapon physics and, although net gain has not yet been attained, significant progress has been made. National Ignition Facility (NIF) capsules have attained fusion gain within the fuel. MagLIF, which is presently being studied at the Z facility, has demonstrated the basic principles of Magneto-Inertial Fusion (MIF), which may provide an alternative path to fusion. Despite these successes there is presently no effort to determine if inertial fusion can be used to generate electrical energy. It would be prudent to have a small program directed to the application of inertial fusion for energy (IFE). This program would not have the same goals as the NNSA and should thus be funded by OFES.
Compact semiconductor device models are essential for efficiently designing and analyzing large circuits. However, traditional compact model development requires a large amount of manual effort and can span many years. Moreover, inclusion of new physics (e.g., radiation effects) into an existing model is not trivial and may require redevelopment from scratch. Machine Learning (ML) techniques have the potential to automate and significantly speed up the development of compact models. In addition, ML provides a range of modeling options that can be used to develop hierarchies of compact models tailored to specific circuit design stages. In this paper, we explore three such options: (1) table-based interpolation, (2) Generalized Moving Least-Squares, and (3) feedforward Deep Neural Networks, to develop compact models for a p-n junction diode. We evaluate the performance of these "data-driven" compact models by (1) comparing their voltage-current characteristics against laboratory data, and (2) building a bridge rectifier circuit using these devices, predicting the circuit's behavior using SPICE-like circuit simulations, and then comparing these predictions against laboratory measurements of the same circuit.
Flood irrigation benefits from low infrastructure costs and maintenance but the scour near the weirs can cause channeling of the flow preventing the water from evenly dispersing across the field. Using flow obstructions in front of the weir could reduce be a low cost solution to reduce the scour. The mitigation strategy was to virtually simulate the effects of various geometric changes to the morphology (e.g. holes and bumps) in front of the weir as a means to diffuse the high intensity flow coming from the gate. After running a parametric study for the dimensions of the shapes that included a Gaussian, semi-circle, and rectangle; a Gaussian-hole in front of the gates showed the most promise to reduce farm field shear-stresses with the added benefit of being easy to construct and implement in practice. Further the simulations showed that the closer the Gaussian-hole could be placed to the gate the sooner the high shear stress could be reduced. To realize the most benefit from this mitigation strategy, it was determined that the maximum depth of the Gaussian-hole should be 0.5 m. The width of the hole in the flow direction and the length of the Gaussian-hole normal to the flow should be 0.5 m and 3 m respectively as measured by the full width at half maximum.