An interpretable machine learning method, physics-informed genetic programming-based symbolic regression (P-GPSR), is integrated into a continuum thermodynamic approach to developing constitutive models. The proposed strategy for combining a thermodynamic analysis with P-GPSR is demonstrated by generating a yield function for an idealized material with voids, i.e., the Gurson yield function. First, a thermodynamic-based analysis is used to derive model requirements that are exploited in a custom P-GPSR implementation as fitness criteria or are strongly enforced in the solution. The P-GPSR implementation improved accuracy, generalizability, and training time compared to the same GPSR code without physics-informed fitness criteria. The yield function generated through the P-GPSR framework is in the form of a composite function that describes a class of materials and is characteristically more interpretable than GPSR-derived equations. The physical significance of the input functions learned by P-GPSR within the composite function is acquired from the thermodynamic analysis. Fundamental explanations of why the implemented P-GPSR capabilities improve results over a conventional GPSR algorithm are provided.
Type 2 high-pressure hydrogen vessels for storage at hydrogen refueling stations are designed assuming a predefined operational pressure cycle and targeted autofrettage conditions. However, the resulting finite life depends significantly on variables associated with the autofrettage process and the pressure cycles actually realized during service, which many times are not to the full range of the design. Clear guidance for cycle counting is lacking, therefore industry often defaults to counting every repressurization as a full range pressure cycle, which is an overly conservative approach. In-service pressure cycles used to predict the growth of cracks in operational pressure vessels results in significantly longer life, since most in-service pressure cycles are only a fraction of the full design pressure range. Fatigue crack growth rates can vary widely for a given pressure range depending on the details of the residual strains imparted during the autofrettage process because of their influence on crack driving forces. Small changes in variables associated with the autofrettage process, e.g., the target autofrettage overburden pressure, can result in large changes in the residual stress profile leading to possibly degraded fatigue life. In this paper, computational simulation was used for sensitivity studies to evaluate the effect of both operating conditions and autofrettage conditions on fatigue life for Type 2 highpressure hydrogen vessels. The analysis in this paper explores these sensitivities, and the results are used to provide guidance on cycle counting. In particular, we identify the pressure cycle ranges that can be ignored over the life of the vessel as having negligible effect on fatigue life. This study also examines the sensitivity of design life to the autofrettage process and the impact on life if the targeted residual strain is not achieved during manufacturing.
High pressure hydrogen storage vessels are frequently retired upon reaching their designed number of pressure cycles, even in cases where the in-use pressure cycles are significantly less severe than the design pressure cycle. One method for extending the life of hydrogen vessels is recertification through non-destructive evaluation (NDE); however, NDE techniques are frequently evaluated with machined defects in test samples rather than fatigue cracks which occur during pressure cycling and may be more difficult to detect. In this paper, 50 mm wide ring sections (called C-rings, since they represent slightly more than half the circumference) were extracted from pressure vessels and mechanically cycled to establish fatigue cracks. Sub-millimeter starter notches were machined, via plunge electrical discharge machining (EDM), to control the location of crack initiation. Crack growth was monitored via direct current potential difference (DCPD) and backface strain gauges, both of which were shown to be good indicators for crack propagation. The C-ring geometry and fatigue crack growth were modeled to demonstrate the ability to monitor/control the crack length and area, which can be used to develop calibration samples of varying crack depth for NDE techniques. Additionally, this sample is intended to evaluate the influence of residual stresses on the sensitivity of NDE techniques, such as the design stresses in autofrettaged vessels.
Type 2 high-pressure hydrogen vessels for storage at hydrogen refueling stations are designed assuming a predefined operational pressure cycle and targeted autofrettage conditions. However, the resulting finite life depends significantly on variables associated with the autofrettage process and the pressure cycles actually realized during service, which many times are not to the full range of the design. Clear guidance for cycle counting is lacking, therefore industry often defaults to counting every repressurization as a full range pressure cycle, which is an overly conservative approach. In-service pressure cycles used to predict the growth of cracks in operational pressure vessels results in significantly longer life, since most in-service pressure cycles are only a fraction of the full design pressure range. Fatigue crack growth rates can vary widely for a given pressure range depending on the details of the residual strains imparted during the autofrettage process because of their influence on crack driving forces. Small changes in variables associated with the autofrettage process, e.g., the target autofrettage overburden pressure, can result in large changes in the residual stress profile leading to possibly degraded fatigue life. In this paper, computational simulation was used for sensitivity studies to evaluate the effect of both operating conditions and autofrettage conditions on fatigue life for Type 2 highpressure hydrogen vessels. The analysis in this paper explores these sensitivities, and the results are used to provide guidance on cycle counting. In particular, we identify the pressure cycle ranges that can be ignored over the life of the vessel as having negligible effect on fatigue life. This study also examines the sensitivity of design life to the autofrettage process and the impact on life if the targeted residual strain is not achieved during manufacturing.