Titanium hydride of varying TiH stoichiometry is used in pyrotechnic compositions. In order to yield consistent performance, manufacturing processes must be developed to ensure precise and reproducible material properties, including composition and morphology. Legacy synthesis protocols are not comprehensive nor are the required apparatuses still available. To guide the development of novel production procedures, this report reviews literature on relevant chemical reactions and diffusion events occurring at elevated temperature in the TiH(2-x)/TiOy system. Titanium hydride exposed to air spontaneously forms a passivating oxide layer. Upon heating, significant hydrogen release, which is accompanied by changes to the surface oxide layer, is noted by 375–400°C. At higher temperatures (above about 500°C) the oxide layer is reported to be essentially nonexistent as a result of oxide-layer dissolution processes and, potentially, oxide-layer reduction due to water formation. Based on the reviewed literature, we hypothesize that, by 500°C, the surface layer consists of an oxyhydride phase, which is a solid solution of oxygen in titanium hydride. We believe that hydrogen release from titanium hydride is controlled by the kinetics of molecular hydrogen desorption on the oxyhydride surface. No literature data is available for corresponding activation energies of the dynamic desorption process, and the equilibrium phase diagram of this three-component system remains largely unexplored as well. These gaps in knowledge might be addressed through coordinated computational modeling and experimental efforts.
The U.S. Strategic Petroleum Reserve is a crude oil storage system run by the U.S. Department of Energy. The reserve consists of 60 active storage caverns spread across four sites in Louisiana and Texas, near the Gulf of Mexico. Beginning in 2016, the SPR began executing U.S. congressionally mandated oil sales. The configuration of the reserve, with a total capacity of greater than 700 MMB, requires raw water to be used instead of saturated brine for oil withdrawals such as for sales. All sales will produce leaching within the caverns used for oil delivery. Twenty-five caverns had a combined total of over 39 MMB of water injected in CY 20 as part of the Exchange for Storage program; oil was withdrawn in the same manner as for congressionally mandated sales. Leaching effects were monitored in these caverns to understand how the oil withdrawals may impact the long-term integrity of the caverns. While frequent sonars are the best way to monitor changes in cavern shape, they can be resource intensive for the number of caverns involved in sales and exchanges. An intermediate option is to model the leaching effects and see if any concerning features develop. The leaching effects were modeled here using the Sandia Solution Mining Code (SANSMIC) . The results indicate that leaching induced features are not of concern in the majority of the caverns, 19 of 25. Six caverns, BH-107, BH-113, BH-114, BM-4, BM-106, and WH-114 have features that may grow with additional leaching and should be monitored as leaching continues in those caverns. Ten caverns had post sale sonars that were compared with SANSMIC results. SANSMIC was able to capture the leaching well , particularly the formation of shelves and flares. A deviation in the SANSMIC and sonar cavern shapes was observed near the cavern floor in caverns with significant floor rise, a process not captured by SANSMIC. These results suggest SANSMIC is a useful tool for monitoring changes in cavern shape due to leaching effects related to sales and exchanges.
Radar is by its basic nature a ranging instrument. If radar range and range-rate measurements from multiple directions can be made and assembled, then multilateration allows locating a feature common to the set of Synthetic Aperture Radar (SAR) images to an accurate 3-D coordinate. The ability to employ effective multilateration algorithms is highly dependent on the geometry of the data collections, and the accuracy with which relative range measurements can be made. The problem can be cast as a least-squares exercise, and the concept of Dilution of Precision can describe the accuracy and precision with which a 3-D location can be made.
Most studies of vortex shedding from a circular cylinder in a gas flow have explicitly or implicitly assumed that the no-slip condition applies on the cylinder surface. To investigate the effect of slip, vortex shedding is simulated using molecular gas dynamics (the direct simulation Monte Carlo method) and computational fluid dynamics (the incompressible Navier-Stokes equations with a slip boundary condition). A Reynolds number of 100, a Mach number of 0.3, and a corresponding Knudsen number of 0.0048 are examined. For these conditions, compressibility effects are small, and periodic laminar vortex shedding is obtained. Slip on the cylinder is varied using combinations of diffuse and specular molecular reflections with accommodation coefficients from zero (maximum slip) to unity (minimum slip). Although unrealistic, bounce-back molecular reflections are also examined because they approximate the no-slip boundary condition (zero slip). The results from both methods are in reasonable agreement. The shedding frequency increases slightly as the accommodation coefficient is decreased, and shedding ceases at low accommodation coefficients (large slip). The streamwise and transverse forces decrease as the accommodation coefficient is decreased. Based on the good agreement between the two methods, computational fluid dynamics is used to determine the critical accommodation coefficient below which vortex shedding ceases for Reynolds numbers of 60-100 at a Mach number of 0.3. Conditions to observe the effect of slip on vortex shedding appear to be experimentally realizable, although challenging.
In April of 2020, Sandia National Laboratories had an urgent need to identify and manage the data that could be used to create mobile applications, models, reports, and visualizations to assist management in safely bringing the workforce onsite during the COVID-19 pandemic. Multiple divisions volunteered to design and build software solutions; meanwhile, requests for new data sources, including duplicate requests, were inundating Information Technology (IT) and data owners. The Enterprise Data Governance Team was assigned to resolve obtaining and accessing new sources of data in an accelerated timeframe. Through successful collaboration with multiple stakeholders and domain owners across Sandia, the Enterprise Data Governance Team rapidly developed a centralized data strategy and solution for use in safeguarding the Sandia workforce during the COVID-19 pandemic. This foundation enabled teams to successfully develop solutions, including reports for executives and management as well as the data for modeling and scientific analysis.
Large volumes of data are being collected by Sandia National Laboratories as part of an active commercial-off-the-shelf (COTS) part testing and surveillance program. This user manual documents Python-based COTS Data Analytics software that has been developed for standardizing, displaying, visualizing, and analyzing the resulting COTS part testing and surveillance data. It is the objective of these software tools to streamline the analysis of COTS testing and surveillance data and improve the efficiency with which test engineers and data analytics experts can pinpoint possible performance and reliability problems in COTS parts.
This paper describes results from an optical-engine investigation of oxygenated fuel effects on ducted fuel injection (DFI) relative to conventional diesel combustion (CDC). Three fuels were tested: a baseline, non-oxygenated No. 2 emissions certification diesel (denoted CFB), and two blends containing potential renewable oxygenates. The first oxygenated blend contained 25 vol% methyl decanoate in CFB (denoted MD25), and the second contained 25 vol% tri-propylene glycol mono-methyl ether in CFB (denoted T25). Whereas DFI and fuel oxygenation primarily curtail soot emissions, intake-oxygen mole fractions of 21% and 16% were employed to explore the potential additional beneficial impact of dilution on engine-out emissions of nitrogen oxides (NOx). It was found that DFI with an oxygenated fuel can attenuate soot incandescence by ~100X (~10X from DFI and an additional ~10X from fuel oxygenation) relative to CDC with conventional diesel fuel, regardless of dilution level and without large effects on other emissions or efficiency. This breaks the soot/NOx trade-off with dilution, enabling simultaneous reductions in both soot and NOx emissions, even with conventional diesel fuel. Significant cyclic variability in soot incandescence for both CDC and DFI suggests that additional improvements in engine-out soot emissions may be possible via improved control of in-cylinder mixture formation and evolution.
Kinetic simulations of Sandia National Laboratories' Z machine are conducted to understand particle transport in the highly magnetized environment of a multi-MA accelerator. Joule heating leads to the rapid formation of electrode surface plasmas. These plasmas are implicated in reducing accelerator efficiency by diverting current away from the load [M.R. Gomez et al., Phys. Rev. Accel. Beams 20, 010401 (2017)PRABCJ2469-988810.1103/PhysRevAccelBeams.20.010401, N. Bennett et al., Phys. Rev. Accel. Beams 22, 120401 (2019)PRABCJ2469-988810.1103/PhysRevAccelBeams.22.120401]. The fully-relativistic, electromagnetic simulations presented in this paper show that particles emitted in a space-charge-limited manner, in the absence of plasma, are magnetically insulated. However, in the presence of plasma, particles are transported across the magnetic field in spite of being only weakly collisional. The simulated cross-gap currents are well-approximated by the Hall current in the generalized Ohm's law. The Hall conductivities are calculated using the simulated particle densities and energies, and the parameters that increase the Hall current are related to transmission line inductance. Analogous to the generalized Ohm's law, we extend the derivation of the magnetized diffusion coefficients to include the coupling of perpendicular components. These yield a Hall diffusion rate, which is equivalent to the empirical Bohm diffusion.
