For flame spread over solid materials, there has traditionally been a large technology gap between fundamental combustion research and the somewhat simplistic approaches used for practical, real-world applications. Recent advances in computational hardware and computational fluid dynamics (CFD)-based software have led to the development of fire field models. These models, when used in conjunction with material burning models, have the potential to bridge the gap between research and application by implementing physics-based engineering models in a transient, multi-dimensional tool. This paper discusses the coupling that is necessary between fire field models and burning material models for the simulation of solid material fires. Fire field models are capable of providing detailed information about the local fire environment. This information serves as an input to the solid material combustion submodel, which subsequently calculates the impact of the fire environment on the material. The response of the solid material (in terms of thermal response, decomposition, charring, and off-gassing) is then fed back into the field model as a source of mass, momentum and energy. The critical parameters which must be passed between the field model and the material burning model have been identified. Many computational issues must be addressed when developing such an interface. Some examples include the ability to track multiple fuels and species, local ignition criteria, and the need to use local grid refinement over the burning material of interest.
High Level Radioactive Waste Management - Proceedings of the Annual International Conference
Boak, D.M.; Painton, L.
Probabilistic forecasting techniques can be used in the treatment of uncertainties in the cost and duration of programmatic alternatives on risk and performance assessment projects. Where significant uncertainties exist and where programmatic decisions must be made despite existing uncertainties, probabilistic techniques may yield important insights into decision options, especially when used in a decision analysis framework and when properly balanced with deterministic analyses. An example application of probabilistic forecasting is presented and described.
We have realized a new class of high-Q resonant cavity using two-dimensional photonic bandgap (PBG) structures and showed that its Q-value can be as high as approximately 23,000 in the mm-wave regime. We further show that its modal properties, such as the resonant frequency, modal linewidth and number of modes, can be tuned by varying the cavity size. In addition, we present a new nano-fabrication technique for constructing PBG resonant cavities in the near infrared and visible spectral regime.
This paper presents a set of motion planners for an exploration vehicle on a simulated rugged terrain. The vehicle has four wheels for its movement and a robotic arm mounted on the vehicle for object manipulation. Given a target point to reach with the hand of the arm, our planners first compute a path for the vehicle to the vicinity of the target, then compute an optimal vehicle position from which the arm can reach the target point, and then plans a path for the arm to reach the target. The vehicle path is planned in two stages. A rough path is planned considering only global features of the terrain, and the path is modified by a local planner to avoid more detailed features of the terrain. The planners are expected to increase the autonomy of robots and improve the efficiencies of exploration missions.
Metallorganic chemical vapor deposition (MOCVD) technology is increasingly recognised as a superior platform for growth of vertical-cavity surface-emitting lasers (VCELs) because of its high throughput, low surface defect density, continuous compositional grading control, and the flexibility for materials and dopant choices. In this paper, it is shown that it is also capable of extremely high wafer uniformity and run-to-run reproducibility.
Frequency modulation is demonstrated in a ring-cavity KTP OPO seeded by frequency-modulated Ti:SAP light. The singly resonant OPO is pumped by a single-longitudinal-mode 532-nm Nd:YAG light, and the 800-nm signal seed is modulated at 3.7 GHz to match the OPO cavity's free spectral range. A comparison is presented of OPO operation with FM and AM seeds that demonstrates the dramatic difference in spectral properties and pulse profiles for the two modulation types. FM modulated absorption measurements made using FM OPO is also demonstrated.
2nd North American Rock Mechanics Symposium, NARM 1996
Arguello, J.G.; Stone, C.M.; Lorenz, J.C.
The ability to predict the mechanical response of rock in three dimensions over the spatial and time scales of geologic interest would give the oil and gas industry the ability to reduce risk on prospects, improve pre-project initial reserve estimates, and lower operating costs. A program has recently been initiated, under the auspices the Advanced Computational Technology Initiative (ACTI), to achieve such a computational technology breakthrough by adapting the unique advanced quasistatic finite element technology developed by Sandia to the mechanics applications important to exploration and production activities within the oil and gas industry. As a pre-cursor to that program, in an effort to evaluate the feasibility of the approach, several complex geologic structures of interest were analyzed with the existing two-dimensional quasistatic finite element code, SANTOS, developed at Sandia. Some examples will be presented and discussed in this paper.
The performance of 21 PV-powered low pressure sodium lighting systems on a multi-use pathway has been documented in this paper. Specific areas for evaluation include the constant voltage and on/off PV charge controllers, flooded deep-cycle lead-antimony and valve regulated lead-acid (VRLA) gel batteries, low pressure sodium ballasts and lights, and vandal resistant PV modules. The PV lighting system lessons learned and maintenance intervals have been documented over the past 2.5-years. The above performance data has shown that with careful hardware selection, installation, and maintenance intervals the PV lighting systems will operate reliably.
We have synthesized periodic mesoporous silica thin films (PMSTF) from homogeneous solutions. To synthesize the films a thin layer of a pH = 7 micellar coating solution that contains TMOS is dip- or spin-coated onto silicon wafers, borosilicate glass, or quartz substrates. Ammonia gas is diffused into the solution and causes rapid hydrolysis and condensation of the TMOS and the formation of periodic mesoporous thin films within approximately 10 seconds. The combination of homogeneous solutions and rapid product formation maximizes the concentration of desired product and provides a controlled, predictable microstructure. The films have been made continuous and crack-free by optimizing initial silica concentration and film thickness.
Materials Research Society Symposium - Proceedings
Samuel, J.
We have used a novel technique, measurement of stress isotherms in microporous thin films, as a means of characterizing porosity. The stress measurement was carried out by applying sol-gel thin films on a thin silicon substrate and monitoring the curvature of the substrate under a controlled atmosphere of various vapors. The magnitude of macroscopic bending stress developed in microporous films depends on the relative pressure and molar volume of the adsorbate and reaches a value of 180 MPa for a relative vapor pressure, P/Po = 0.001, of methanol. By using a series of molecules, and observing both the magnitude and the kinetics of stress development while changing the relative pressure, we have determined the pore size of microporous thin films. FTIR measurements were used to acquire adsorption isotherms and to compare pore emptying to stress development, about 80% of the change in stress takes place with no measurable change in the amount adsorbed. We show that for sol-gel films, pore diameters can be controlled in the range of 5-8 angstroms by `solvent templating'.
Electron cyclotron resonance (ECR) etching of GaP, GaAs, InP, and InGaAs are reported as a function of percent chlorine-containing gas for Cl2/Ar, Cl2/N2, BCl3/Ar, and BCl3/N2 plasma chemistries. GaAs and GaP etch rates were faster than InP and InGaAs, independent of plasma chemistry due to the low volatility of the InClx etch products. GaAs and GaP etch rates increased as %Cl2 was increased for Cl2/Ar and Cl2/N2 plasmas. The GaAs and GaP etch rates were much slower in BCl3-based plasmas due to lower concentrations of reactive Cl, however enhanced etch rates were observed in BCl3/N2 at 75% BCl3. Smooth etched surfaces were obtained over a wide range of plasma chemistries.
Development of a complementary heterostructure field effect transistor (CHFET) technology for low-power, mixed-mode digital-microwave applications is presented. An earlier digital CHFET technology with independently optimizable transistors which operated with 319 ps loaded gate delays at 8.9 fJ is reviewed. Then work demonstrating the applicability of the digital nJFET device as a low-power microwave transistor in a hybrid microwave amplifier without any modification to the digital process is presented. A narrow band amplifier with a 0.7 × 100 μm nJFET as the active element was designed, constructed, and tested. At 1 mW operating power, the amplifier showed 9.7 dB of gain at 2.15 GHz and a minimum noise figure of 2.5 dB. In addition, next generation CHFET transistors with sub 0.5 μm gate lengths were developed. Cutoff frequencies, ft of 49 GHz and 11.5 GHz were achieved for n- and p-channel FETs with 0.3 and 0.4 μm gates, respectively. These FETs will enable both digital and microwave circuits with enhanced performance.
This paper describes a study of the underlying physical mechanisms governing the threshold properties of a VCSEL. In particular, it theoretically and experimentally evaluates the mechanisms that effect the threshold properties as a function of emission wavelength. Other important issues, such as the dependence of the threshold properties on microcavity dimensions, we discussed.
Thin-film decoupling capacitors based on ferroelectric (Pb,La)(Zr,Ti)O3 films are being developed for use in advanced packaging applications. The increased integration that can be achieved by replacing surface-mount capacitors should lead to decreased package volume and improved high-speed performance. For this application, chemical solution deposition is an appropriate fabrication technique since it is a low-cost, high-throughput process. The use of relatively thick Pt electrodes (approximately 1 μm) to minimize series resistance and inductance is a unique aspect to fabricating these devices. In addition, the important electrical properties are discussed, with particular emphasis on lifetime measurements, which suggest that resistance degradation will not be a severe limitation on device performance. Finally, some of the work being done to develop methods of integrating these thin-film capacitors with ICs and MCMs is presented.
Materials Research Society Symposium - Proceedings
Raymond, M.V.
La0.5Sr0.5CoO3 (LSCO) thin films have been deposited, using RF magnetron sputter-deposition for use as an electrode material for Pb(Zr,Ti)O3 (PZT) thin film capacitors. The effect of the O2:Ar sputter gas ratio during deposition, on the LSCO film properties was investigated. It was found that the resistivity of the LSCO films deposited at ambient temperature decreases as the O2:Ar ratio was increased for both the as-deposited and annealed films. In addition, it was found that thin overlayers of LSCO tend to stabilize the underlying Pt//Ti electrode structure during subsequent thermal processing. The LSCO//Pt//Ti composite electrode stack has a low resistivity and provides excellent fatigue performance for PZT capacitors. Furthermore, the LSCO//Pt//Ti electrode sheet resistance does not degrade with annealing temperature and the electrode does not display hillock formation. Possible mechanisms for the stabilization of the Pt//Ti electrode with LSCO overlayers will be discussed.
The relative viscosity of concentrated suspensions of mixtures of rodlike and spherical particles are measured by falling-ball rheometry. The suspensions are well mixed and homogeneous in the sense that the particles are well dispersed and the rods are randomly oriented. For a constant total volume fraction of solids, the addition of spheres to suspensions of rods results in large decrease in the relative viscosity of the suspension. In these experiments the length of the suspended rods is approximately 10 times the diameter of the suspended spheres. Due to this difference in the characteristic sizes of the two types of particles, the spheres may be considered as part of the suspending homogeneous continuum. A simple model based on this physical picture, after Farris [1968], is very successful in predicting the relative viscosity of the mixed suspensions.
In recent studies, we used the Interfacial Force Microscope in a nanoindenter mode to survey the nanomechanical properties of Au films grown on various substrates. Quantitative tabulations of the indentation modulus and the maximum shear stress at the plastic threshold showed consistent values over individual samples but a wide variation from substrate to substrate. These values were compared with film properties such as the surface roughness, average grain size and interfacial adhesion and no correlation was found. However, in a subsequent analysis of the results, we found consistencies which support the integrity of the data and point to the fact that the results are sensitive to some property of the various film/substrate combinations. In the present paper, we discuss these consistencies and show recent measurements which strongly suggest that the property that is being probed is the residual stress in the films caused by their interaction with the substrate surfaces.
The study of gain properties in group-III nitride quantum wells is complicated by several factors. In view of this, an approach is presented that involves a first-principles bandstructure calculation, the results of which are incorporated into a microscopic laser theory. The band structure calculation applies a density-functional method. This method provides a single analytical model for computing the group-II nitride material properties, thus ensuring consistency in the values for the different bandstructure parameters, and circumventing the discrepancies present in the literature due to different experimental conditions, or different computational methods. With a complete set of the relevant material parameters, it is possible to study the effects of strain and quantum confinement.
Monochromatic imaging was used to investigate the excited-state density distributions of Fe and Fe+ in the inter-electrode gap region of a 3,100 A dc metal vapor arc burning between molten iron surfaces in a vacuum arc furnace. Multiple images were acquired at four wavelengths. The images were corrected and Abel inverted to yield the absolute radial intensity distributions for Fe and Fe+ in the inter-electrode gap region. The results show a structured, axisymmetric plasma consisting of a high density 'core' of Fe+ emitters centered between the electrode surfaces situated against a relatively broad, flat excited-state Fe distribution.
6th Symposium on Multidisciplinary Analysis and Optimization
Campbell, J.E.; Painton, L.A.
This paper examines a novel optimization technique called genetic algorithms and its application to the optimization of reliability allocation strategies. Reliability allocation should occur in the initial stages of design, when the objective is to determine an optimal breakdown or allocation of reliability to certain components or subassemblies in order to meet system objectives. The reliability allocation optimization is applied to the design of a cluster tool, a highly complex piece of equipment used in semiconductor manufacturing. The problem formulation is presented, including decision variables, performance measures and constraints, and genetic algorithm parameters. Piecewise “effort curves” specifying the amount of effort required to achieve a certain level of reliability for each component or subassembly are defined. The genetic algorithm evolves or picks those combinations of “effort” or reliability levels for each component which optimize the objective of maximizing Mean Time Between Failures while staying within a budget. The results show that the genetic algorithm is very efficient at finding a set of robust solutions. A time history of the optimization is presented, along with histograms of the solution space fitness, MTBF, and cost for comparative purposes.
Conference Proceedings from the International Symposium for Testing and Failure Analysis
Liang, A.Y.
We present the results of recent failure analysis of an advanced, 0.5 um, fully planarized, triple metallization CMOS technology. A variety of failure analysis (FA) tools and techniques were used to localize and identify defects generated by wafer processing. These include light (photon) emission microscopy (LE), fluorescent microthermal imaging (FMI), focused ion beam cross sectioning, SEM/voltage contrast imaging, resistive contrast imaging (RCI), and e-beam testing using an IDS-5000 with an HP 82000. The defects identified included inter- and intra-metal shorts, gate oxide shorts due to plasma processing damage, and high contact resistance due to the contact etch and deposition process. Root causes of these defects were determined and corrective action was taken to improve yield and reliability.
Polysilicon surface micromachining is a technology for manufacturing Micro-Electro-Mechanical Systems (MEMS) which has, as its basis, the manufacturing methods and tool sets used to manufacture the integrated electronic circuit. This paper describes a three-level mechanical-polysiiicon surface-micromachining technology and includes a discussion of the advantages of this level of process complexity along with issues which affect device fabrication and performance. Historically, the primary obstacles to multi-level polysilicon fabrication were related to the severe wafer topography generated by the repetition of film depositions and etching. The introduction of Chemical Mechanical Polishing (CMP) to surface micromachining has largely removed these issues and opened significant avenues for device complexity. Several examples of three-level devices with the benefits of CMP are presented. Of primary hindrance to the widespread use of polysilicon surface micromachining, and in particular microactuation mechanisms, are issues related to the device surfaces. The closing discussion examines the potential of several latter and postfabrication processes to circumvent or to directly alleviate the surface problems.
We apply a number of complementary characterization techniques including electron paramagnetic resonance, optical absorption, and photoluminescence spectroscopies to characterize a wide range of different ZnO phosphor powders. We generally observe a good correlation between the 510-nm green emission intensity and the density of paramagnetic isolated oxygen vacancies. In addition, both quantities are found to peak at a free-carrier concentration ne, of about 1.4×1018 cm-3. We also find that the green emission intensity can be strongly influenced by free-carrier depletion at the particle surface, especially for small particles and/or low doping. Our data suggest that the green PL in ZnO phosphors is due to the recombination of electrons in singly occupied oxygen vacancies with photoexcited holes in the valence band.
Crystal lattices are infinite periodic graphs that occur naturally in a variety of geometries and which are of fundamental importance in polymer science. Discrete models of protein folding use crystal lattices to define the space of protein conformations. Because various crystal lattices provide discretizations of the same physical phenomenon, it is reasonable to expect that there will exist "invariants" across lattices that define fundamental properties of the protein folding process; an invariant defines a property that transcends particular lattice formulations. This paper identifies two classes of invariants, defined in terms of sublattices that are related to the design of algorithms for the structure prediction problem. The first class of invariants is used to define a master approximation algorithm for which provable performance guarantees exist. This algorithm can be applied to generalizations of the hydrophobic-hydrophilic model that have lattices other than the cubic lattice, including most of the crystal lattices commonly used in protein folding lattice models. The second class of invariants applies to a related lattice model. Using these invariants, we show that for this model the structure prediction problem is intractable across a variety of threedimensional lattices. It turns out that these two classes of invariants are respectively sublattices of the two-and three-dimensional square lattice. As the square lattices are the standard lattices used in empirical protein folding studies, our results provide a rigorous confirmation of the ability of these lattices to provide insight into biological phenomenon. Our results are the first in the literature that identify algorithmic paradigms for the protein structure prediction problem that transcend particular lattice formulations.
GOMA is a two- and three-dimensional finite element program which excels in analyses of manufacturing processes, particularly those involving free or moving interfaces. Specifically, the full-Newton-coupled heat, mass, momentum, and pseudo-solid mesh motion algorithm makes GOMA ideally suited for simulating processes in which the bulk fluid transport is closely coupled to the interfacial physics. Examples include, but are not limited to, coating and polymer processing flows, soldering, crystal growth, and solid-network or solution film drying. The code is based on the premise that any boundary can be (1) moving or free, with an apriori unknown position dictated by the distinguishing physics, (2) fixed, according to a global analytical representation, or (3) moving in time and space under user-prescribed kinematics. The goal is to enable the user to predict boundary position or motion simultaneously with the physics of the problem being analyzed and to pursue geometrical design studies and fluid-structure interaction problems. The moving mesh algorithm treats the entire domain as a computational Lagrangian solid that deforms subject to the physical principles which dictate boundary position. As an added benefit, the same Lagrangian solid mechanics can be exploited to solve multi-field problems for which the solid motion and stresses interact with other transport phenomena, either within the same material phase (e.g. shrinking coating) or in neighboring material phases (e.g. flexible blade coating). Thus, analyses of many fluid-structure interaction problems and deformable porous media problems are accessible. This document serves as a user`s guide and reference for GOMA and provides a brief overview of GOMA`s capabilities, theoretical background, and classes of problems for which it is targeted.
The prediction of stresses and displacements around tunnels buried deep within the earth is an important class of geomechanics problems. The material behavior immediately surrounding the tunnel is typically nonlinear. The surrounding mass, even if it is nonlinear, can usually be characterized by a simple linear elastic model. The finite element method is best suited for modeling nonlinear materials of limited volume, while the boundary element method is well suited for modeling large volumes of linear elastic material. A computational scheme that couples the finite element and boundary element methods would seem particularly useful for geomechanics problems. A variety of coupling schemes have been proposed, but they rely on direct solution methods. Direct solution techniques have large storage requirements that become cumbersome for large-scale three-dimensional problems. An alternative to direct solution methods is iterative solution techniques. A scheme has been developed for coupling the finite element and boundary element methods that uses an iterative solution method. This report shows that this coupling scheme is valid for problems where nonlinear material behavior occurs in the finite element region.
The primary goal of the Individual Plant Examination (IPE) Program was for licensees to identify plant-unique vulnerabilities and actions to address these vulnerabilities. A review of these vulnerabilities and plant improvements that were identified in the IPEs was performed as part of the IPE Insights Program sponsored by the U.S. Nuclear Regulatory Commission (NRC). The purpose of this effort was to characterize the identified vulnerabilities and the impact of suggested plant improvements. No specific definition for {open_quotes}vulnerability{close_quotes} was provided in NRC Generic Letter 88-20 or in the subsequent NRC IPE submittal guidance documented in NUREG-1335. Thus licensees were left to use their own definitions. Only 20% of the plants explicitly stated that they had vulnerabilities. However, most licensees identified other plant improvements to address issues not explicitly classified as vulnerabilities, but pertaining to areas in which overall plant safety could potentially be increased. The various definitions of {open_quotes}vulnerability{close_quotes} used by the licensees, explicitly identified vulnerabilities, proposed plant improvements to address these vulnerabilities, and other plant improvements are summarized and discussed.
In 1991, at the direction of the United Nations Security Council, UNSCOM and IAEA developed plans for On-going Monitoring and Verification (OMV) in Iraq. The plans were accepted by the Security Council and remote monitoring and atmospheric sampling equipment has been installed at selected sites in Iraq. The remote monitoring equipment consists of video cameras and sensors positioned to observe equipment or activities at sites that could be used to support the development or manufacture of weapons of mass destruction, or long-range missiles. The atmospheric sampling equipment provides unattended collection of chemical samples from sites that could be used to support the development or manufacture of chemical weapon agents. To support OMV in Iraq, UNSCOM has established the Baghdad Monitoring and Verification Centre. Imagery from the remote monitoring cameras can be accessed in near-real time from the Centre through RIF communication links with the monitored sites. The OMV program in Iraq has implications for international cooperative monitoring in both global and regional contexts. However, monitoring systems such as those used in Iraq are not sufficient, in and of themselves, to guarantee the absence of prohibited activities. Such systems cannot replace on-site inspections by competent, trained inspectors. However, monitoring similar to that used in Iraq can contribute to openness and confidence building, to the development of mutual trust, and to the improvement of regional stability.
Extensive work has been conducted by industry to develop lead-free solders for electronics applications. The driving force behind this effort is pressure to ban or tax the use of lead-bearing solders. There has been further interest to reduce the use of hazardous chemical cleaners. Lead-free soldering and low-residue, ``no clean`` assembly processing are being considered as solutions to these environmental issues. Most of the work has been directed toward commercial and military printed wiring board (PWB) technology, although similar problems confront the hybrid microcircuit (HMC) industry, where the development of lead-free HMC solders is generally lagging. Sandia National Laboratories is responsible for designing a variety of critical, high reliability hybrid components for radars. Sandia has consequently initiated a project, as part of its Environmentally Conscious Manufacturing program, to develop low-residue, lead-free soldering for HMCs. This paper discusses the progress of that work.
Breccia pipes in southeastern New Mexico are local dissolution-collapse features that formed over the Capitan reef more than 500,000 years ago. During early site studies for the Waste Isolation Pilot Plant (WIPP), the threat to isolation by these features was undetermined. Geophysical techniques, drilling, and field mapping were used beginning in 1976 to study breccia pipes. None were found at the WIPP site, and they are considered unlikely to be a significant threat even if undetected. WIPP documents related to breccia pipe studies were assembled, inspected, and analyzed, partly to present a history of these studies. The main objective is to assess how well the record reflects the purposes, results, and conclusions of the studies from concept to decision-making. The main record source was the Sandia WIPP Central File (SWCF). Early records (about 1975 to 1977) are very limited, however, about details of objectives and plans predating any investigation. Drilling programs from about 1977 were covered by a broadly standardized statement of work, field operations plan, drilling history, and basic data report. Generally standardized procedures for peer, management, and quality assurance review were developed during this time. Agencies such as the USGS conducted projects according to internal standards. Records of detailed actions for individual programs may not be available, though a variety of such records were found in the SWCF. A complete written record cannot be reconstructed. With persistence, a professional geologist can follow individual programs, relate data to objectives (even if implied), and determine how conclusions were used in decision-making. 83 refs.
The objective of this study is to determine how the jet fuel contained in aircraft wing tanks disperses on impact with a soft terrain, i.e., soils, at high impact velocities. The approach used in this study is to combine experimental and numerical methods. Tests were conducted with an approximately 1/42 linear-scale mass-model of a 1/4 span section of a C-141 wing impacting a sand/clay mixture. The test results showed that within the uncertainty of the data, the percentage of incident liquid mass remaining in the crater is the same as that qualitatively described in earlier napalm bomb development studies. Namely, the percentage of fuel in the crater ranges from near zero for grazing impacts to 25%--50% for high angles of impact. To support a weapons system safety assessment (WSSA), the data from the current study have been reduced to correlations. The numerical model used in the current study is a unique coupling of a Smooth Particle Hydrodynamics (SPH) method with the transient dynamics finite element code PRONTO. Qualitatively, the splash, erosion, and soil compression phenomena are all numerically predicted. Quantitatively, the numerical method predicted a smaller crater cross section than was observed in the tests.
The BostoMatic 300 (BM300) machining center is an integral part of an ongoing Laboratory Directed Research and Development (LDRD) project at Sandia National Laboratories (SNL) titled ``Intelligent Tools for On-Machine Acceptance of Precision Machined Components``. On-Machine Acceptance (OMA) is a new agile manufacturing concept being developed for machine tools at SNL. The concept behind OMA is the integration of product design, fabrication, and qualification processes. To achieve the OMA integration of design, fabrication and qualification processes, the BM300 will function as a fabrication and inspection tool. The BM300 performance evaluation took place in July and August of 1994. Tests were conducted in the Advanced Manufacturing Process Laboratory (AMPL), Bldg 878, SNL/NM using a BM300 serial number MM-590. All testing was in accordance with ANSI/ASME B5.54-1992 ``Performance Evaluation of Numerically Controlled Machining Centers``, unless otherwise noted. The results of all tests were compiled and documented in Section 4.0. The ANSI B5.54 testing of the BM300 was divided into six areas. Those areas are linear displacement accuracy, angular displacement accuracy, axis of rotation (spindle), geometric accuracy, volumetric performance, and machine performance as a measuring tool. Details regarding the six tests and test equipment are documented in Section 4.0. As of August 1994 testing of the BM300 in the area of ``Machine Performance as a Measuring Tool`` had not been completed. Future testing in this area may incorporate the LDRD test part along with the appropriate ANSI B5.54 specification in determining the BM300 accuracy.
Sandia National Laboratories in Albuquerque, New Mexico, has adopted strategic, standards-based telecommunication technologies to deliver high-speed communication services to its research and development community. The architecture to provide these services specifies a cabling system capable of carrying high-bandwidth signals to each desktop. While the facilities infrastructure of Sandia has been expanding and evolving over the past four decades to meet the needs of this premier research and development community, the communications infrastructure has remained essentially stagnant. The need to improve Sandia`s telecommunication cable infrastructure gave rise to the Intra-building Recabling Project (IRP). The IRP directed Sandia`s efforts to modernize and standardize the communications infrastructure throughout its New Mexico campus. This report focuses on the development and implementation of the project`s design considerations, concepts, and standards, as well as the adopted transmission media and supporting delivery subsystems.
Switch tubes are used in nuclear weapon firing sets and are required to be reliable and impervious to gas permeation for many years. To accomplish this, a gold plated coating of approximately 25 microns is required over all metal surfaces on the tube exterior. The gold has historically been plated using gold cyanide plating chemistry. In this work we proposed to replace the cyanide plating bath with an environmentally friendlier sulfite gold plating bath. Low and high pH sulfite plating chemistries were investigated as possible replacements for the cyanide gold plating chemistry. The low pH plating chemistry demonstrated a gold plated coating which met the high purity, grain size, and hardness requirements for switch tubes. The high pH chemistry was rejected primarily because the hardness of the gold plated coatings was too high and exceeded switch tube coating requirements. A problem with nodule formation on the gold plated surface using the low pH chemistry had to be resolved during this evaluation. The nodule formation was postulated to be produced by generation of SO{sub 2} in the low pH bath causing gold to be precipitated out when the sulfite concentration falls below a minimum level. The problem was resolved by maintaining a higher sulfite concentration and providing an active filtration system during plating. In this initial study, there were no major obstacles found when using a sulfite gold bath for switch tube plating, however, further work is needed on bath control and bath life before adopting it as the primary plating chemistry.
The US nuclear weapon stockpile is entering a different era. Continuous introduction of new weapons into the stockpile, a large production capacity, and underground nuclear testing played important roles in how the nuclear weapons stockpile was managed in the past. These are no longer elements of the nuclear weapons program. Adjustments need to be made to compensate for the loss of these elements. The history of the stockpile indicates that problems have been found in both nuclear and nonnuclear components through a variety of methods including the Stockpile Evaluation Program, stockpile management activities, underground nuclear tests, and research activities. Changes have been made to the stockpile when necessary to assure safety, performance, and reliability. There have been problems found in each of the weapon types expected to be in the stockpile in the year 2000. It is reasonable to expect problems will continue to arise in the stockpile as it ages beyond the original design expectations.
Natural fractures and in situ stresses commonly dictate subsurface reservoir permeability and permeability anisotropy, as well as the effectiveness of stimulation techniques in low-permeability, natural gas reservoirs. This paper offers an initial prediction for the orientations of the fracture and stress systems in the tight gas reservoirs of the Frontier Formation, in the Green River basin of southwestern Wyoming. It builds on a previous report that addressed fractures and stresses in the western part of the basin and on ideas developed for the rest of the basin, using the principle that thrust faults are capable of affecting the stress magnitudes and orientations in little-deformed strata several hundreds of kilometers in front of a thrust. The prediction of subsurface stresses and natural fracture orientations is an undertaking that requires the willingness to revise models as definitive data are acquired during drilling. The predictions made in this paper are offered with the caveat that geology in the subsurface is always full of surprises.
Probabilistic safety analyses (PSAs) frequently depend on fault tree and event tree models, using probabilities of `events` for inputs. Uncertainty or variability is sometimes included by assuming that the input probabilities vary independently and according to an assumed stochastic probability distribution modes. Evidence is accumulating that this methodology does not apply well to some situations, most significantly when the inputs contain a degree of subjectivity or are dependent. This report documents the current status of an investigation into methods for effectively incorporating subjectivity and dependence in PSAs and into the possibility of incorporating inputs that are partly subjective and partly stochastic. One important byproduct of this investigation was a computer routine that combines conventional PSA techniques with newly developed subjective techniques in a `hybrid` (subjective and conventional PSA) program. This program (PHASER) and a user`s manual are now available for beta use.
Stereolithography is a rapid prototyping method that is becoming an important product realization and concurrent engineering tool, with applications in advanced and agile manufacturing. During the build process, material behavior plays a significant role in the mechanics leading to internal stresses and, potentially, to distortion (curling) of parts. The goal of the ``Stereolithography Manufacturing Process Modeling and Optimization`` LDRD program was to develop engineering tools for improving overall part accuracy during the stereolithography build process. These tools include phenomenological material models of solidifying stereolithography photocurable resins and a 3D finite element architecture that incorporates time varying material behavior, laser path dependence, and structural linkage. This SAND report discusses the in situ measurement of shrinkage and force relaxation behavior of two photocurable resins, and the measurement of curl in simple cantilever beams. These studies directly supported the development of phenomenological material models for solidifying resins and provided experimental curl data to compare to model predictions.
A technique called ripple fire used in quarry blasts produces modulations in the spectra of these events. The Deployable Seismic Verification System (DSVS) was installed at the Pinedale Seismic Research Facility in Wyoming, an area with a lot of mining activity. DSVS records at frequencies up to 50 Hz and these data provides us with a unique opportunity to determine how well we can discriminate quarry blasts and if there are operational benefits from using high frequency (>20 Hz) data. We have collected a database of 646 events consisting of known earthquakes, known quarry blasts and unknown signals. We have started to calculate preliminary spectrograms if we get the time-independent banding from the quarry blasts, and at what frequencies the banning occurs. We also detail what we hope to accomplish in FY 1996.
A gridless method has been developed for the simulation of coupled fluid/structural interactions over arbitrary bodies. This method uses Eulerian-based points arbitrarily distributed over the computational domain with no formal connectivity as typically required for a traditional grid. Comparisons are made with known exact solutions for simple two-dimensional model problems. Methods of improving the accuracy of the current implementation by using higher order approximations have been implemented. Accuracy improvement by using point adaption has been investigated. Plane strain and axisymmetric shells have been added to the code structural code PRONTO2D for future fluid/structural calculations. To date, coupled fluid/structure calculations have not been made.
Smith, R.E.; Warren, M.E.; Wendt, J.R.; Vawter, G.A.
This paper presents a high-efficiency, dielectric, subwavelength surface relief ``blazed grating`` and reports recent results on a subwavelength ``anti-reflection`` surface. These structures were designed for use at 975 nm, probably the shortest wavelength for which semiconductor structures of these types have been successfully demonstrated. They were fabricated in GaAs substrates.
Tools and techniques developed to measure stresses and motions on underground nuclear and high explosive tests in the tuff geologies at the Nevada Test Site are described in this document. The thrust of the measurements was to understand containment phenomenology. The authors concentrate on the fluid-coupled ytterbium gage; it was fielded to measure dynamic stress in the 0.2 to 20 kilobar range and the subsequent, low amplitude residual stress. Also described are accelerometer packages; their traces were integrated to obtain particle motion. Various cable survival techniques were investigated with field measurements for they wished to extend the measurements to late-time. Field measurements were also made to address the gage inclusion problem. Work to date suggests that the problem is a minimum when the stress level is above the yield strength of the host rock and grout. Below the yield level stress amplitudes in the grouted hole can range from 60 to 200% of the stress in the host rock.
Intense magnetic fields exist in the immediate vicinity of a lightning strike (and near power lines). Conducting barriers increase the rise time (and thus decrease the rise rate) interior to the barrier, but typically do not prevent penetration of the magnetic field, since the lightning current fall time may be larger than the barrier diffusion time. Thus, substantial energy is present in the interior field, although the degradation of rise rate makes it more difficult to couple into electrical circuits. This report assesses the threat posed by the diffusive magnetic field to interior components and wire loops (where voltages are induced). Analytical and numerical bounding analyses are carried out on a pill box shaped conducting barrier to develop estimates for the worst case magnetic field threats inside the system. Worst case induced voltages and energies are estimated and compared with threshold charge voltages and energies on the output capacitor of the system. Variability of these quantities with respect to design parameters are indicated. The interior magnetic field and induced voltage estimates given in this report can be used as excitations for more detailed interior and component models.
The Charpy-V (C{sub V}) notch ductility and tension test properties of three reactor pressure vessel (RPV) steel materials were determined for the 288{degree}C (550{degree}F) irradiated (I), 288{degree}C (550{degree}F) irradiated + 454{degree}C (850{degree}F)-168 h postirradiation annealed (IA), and 288{degree}C (550{degree}F) reirradiated (IAR) conditions. Total fluences of the I condition and the IAR condition were, respectively, 3.33 {times} 10{sup 19} n/cm{sup 2} and 4.18 {times} 10{sup 19} n/cm{sup 2}, E > 1 MeV. The irradiation portion of the IAR condition represents an incremental fluence increase of 1. 05 {times} 10{sup 19} n/cm{sup 2}, E > 1 MeV, over the I-condition fluence. The materials (specimens) were supplied by the Yankee Atomic Electric Company and represented high and low nickel content plates and a high nickel, high copper content weld deposit prototypical of the Yankee-Rowe reactor vessel. The promise of the IAR method for extending the fluence tolerance of radiation-sensitive steels and welds is clearly shown by the results. The annealing treatment produced full C{sub V} upper shelf recovery and full or nearly full recovery in the C{sub V} 41 J (30 ft-lb) transition temperature. The C{sub V} transition temperature increases produced by the reirradiation exposure were 22% to 43% of the increase produced by the first cycle irradiation exposure. A somewhat greater radiation embrittlement sensitivity and a somewhat greater reirradiation embrittlement sensitivity was exhibited by the low nickel content plate than the high nickel content plate. Its high phosphorus content is believed to be responsible. The IAR-condition properties of the surface vs. interior regions of the low nickel content plate are also compared.
This report is a part of the Test Information Program (TIP) at Sandia National Laboratories. It is an interim report, written primarily as an instruction document to aid in current work on the project. It addresses some found in storing and retrieving data from nuclear field tests conducted over the past five decades, primarily instrumentation data recorded from tests at the Nevada Test Site. First, the TIP data unit for storing and transporting TIP data is described. The data in the TIP data unit is typically recorded in a universal medium such as the portable optical or magnetic disk, or the tape cassette. Each TIP data unit is portable, and is also self-contained in the sense that it includes a set of related test data files, along with complete instructions and software for retrieval of the data by an unknown user, possibly on an unknown platform. Secondly, we describe the use of current software for compressing and waveform data, for authenticating and checking for errors in data processing files to be used on foreign platforms.
China`s central political authorities have constructed a system which is designed to enable them to exert their personal influence and control over each level of every organization in the country -- both civil and military. The Communist Party of China (CPC) is represented at all levels of each and every organization, including the People`s Liberation Army (PLA). These Party entities are intended to both provide oversight and to ensure that Party policies, directives and orders are obeyed. This penchant for political control, which may have its roots in China`s imperial past, appears to have been reinforced by the early developmental path chosen by the Party`s leadership. Current attempts aimed at maintaining political control of its resources, especially the military, are embodied in the formal system of {open_quotes}Political Work.{close_quotes} In the PLA, this system of political control results in the involvement of political organs in day-to-day military matters to an extent unheard of in the West. Further work is needed in order to understand, more fully, both the system of {open_quotes}Political Work{close_quotes} and its contributions to the overall military (and civil) command and control philosophic of the Communist Party of China.
In reactive ion etching (RIE) of GaN, the ion bombardment can damage the material, so it is necessary to develop plasma etch processes. This paper reports etching of GaN in an ECR (electron cyclotron resonance) etch system using both the ECR/RIE mode and the RIE-only mode. Group III (Ga, In, Al) nitride ECR etching is reviewed as a function of plasma chemistry, power, temperature, and pressure; as the ECR microwave power increased, the ion density and etch rates increased, with the etch rate increasing the most for InN. GaN etch rates > 6500 {angstrom}/min have been observed in the ECR/RIE mode. 2 figs, 6 refs.
Sandia National Laboratories manages the US Department of Energy program for slimhole drilling. The principal objective of this program is to expand proven geothermal reserves through increased exploration made possible by lower-cost slimhole drilling. For this to be a valid exploration method, however, it is necessary to demonstrate that slimholes yield enough data to evaluate a geothermal reservoir, and that is the focus of Sandia`s current research.
As Archive Coordinator for Sandia National Laboratories Corporate Archives, I am responsible for promoting the preservation and value of Sandia`s history. Today I will talk about one important part of Sandia`s historical record--the laboratory notebook. I will start with some brief background on Sandia National Laboratories, including the Laboratories` mission and an example of how the gold in one lab notebook helped to give a picture of Sandia`s early history. Next, I will talk about the use of notebooks at Sandia Labs, how they represent technology developed at Sandia, and include noteworthy examples of how patent information has been collected, used, and released to the public. Then, I will discuss how the National Competitiveness Technology Transfer Act of 1989 authorized technology transfer initiatives and the exclusive use of patented information, resulting in many golden opportunities for the national laboratories to work with private industry to further technology. I will briefly discuss laboratory notebook retention schedules and mention a new initiative to better utilize Laboratory notebooks. And, finally, I will summarize how the `gold` in laboratory notebooks in government archives are a reflection of the valuable and extensive research authorized and funded by the government to benefit the public.
Most routing problems depend on several important variables: transport distance, population exposure, accident rate, mandated roads (e.g., HM-164 regulations), and proximity to emergency response resources are typical. These variables may need to be minimized or maximized, and often are weighted. `Objectives` to be satisfied by the analysis are thus created. The resulting problems can be approached by combining spatial analysis techniques from geographic information systems (GIS) with multiobjective analysis techniques from the field of operations research (OR); we call this hybrid multiobjective spatial analysis` (MOSA). MOSA can be used to discover, display, and compare a range of solutions that satisfy a set of objectives to varying degrees. For instance, a suite of solutions may include: one solution that provides short transport distances, but at a cost of high exposure; another solution that provides low exposure, but long distances; and a range of solutions between these two extremes.
Three and four-layer backpropagation artificial neural networks have been used to predict the power output of a liquid metal reflux solar receiver. The networks were trained using on-sun test data recorded at Sandia National Laboratories in Albuquerque, New Mexico. The preliminary results presented in this paper are a comparison of how different size networks train on this particular data. The results give encouragement that it will be possible to predict output power of a liquid metal receiver under a variety of operating conditions using artificial neural networks.
We have conducted a real time, two-dimensional light scattering study of the nonlinear dynamics of field-induced structures in an electrorheological fluid subjected to oscillatory shear. We have developed a kinetic chain model of the observed dynamics by considering the response of a fragmenting/aggregating particle chain to the prevailing hydrodynamic and electrostatic forces. This structural theory is then used to describe the nonlinear rheology of ER fluids.
This paper describes recent work to make high quality quartz gauge (temporal and spatial) shock wave measurements in a pulsed ion beam environment. Intense ion beam radiation, nominally 1 MeV protons, was deposited into material samples instrumented with shunted quartz gauges adjacent to the ion deposition zone. Fluence levels were chosen to excite three fundamentally different material response modes (1) strong vapor, (2) combined vapor and melt phase and (3) thermoelastic material response. A unique quartz gauge design was utilized that employed printed circuit board (PCB) technology to facilitate electrical shielding, ruggedness, and fabrication @e meeting the essential one dimensional requirements of the characterized Sandia shunted quartz gauge. Shock loading and unloading experiments were conducted to evaluate the piezoelectric response of the coupled quartz gauge/PCB transducer. High fidelity shock wave profiles were recorded at the three ion fluence levels providing dynamic material response data for vapor, melt and solid material phases.
Terminal propagation is a method developed in the circuit placement community for adding constraints to graph partitioning problems. This paper adapts and expands this idea, and applies it to the problem of partitioning data structures among the processors of a parallel computer. We show how the constraints in terminal propagation can be used to encourage partitions in which messages are communicated only between architecturally near processors. We then show how these constraints can be handled in two important partitioning algorithms, spectral bisection and multilevel-KL. We compare the quality of partitions generated by these algorithms to each other and to Partitions generated by more familiar techniques.
The viscous response of electrorheological fluids is usually manipulated through the use of DC or uniaxial AC electric fields. The result is that fibrillated structures parallel to the field form in a quiescent fluid; the distortion of such structures in a flow determines the enhanced viscous response, at least at low and moderate flow rates. We have conducted preliminary studies of electrorheological response in a different field configurations rotating electric field. With respect to the uniaxial AC case. there are two new developments in this type of field. The structures formed are disk-like, in the plane of the rotating field. Furthermore, the structures rotate either with or against the field, depending on the dielectric or conductivity contrast with the surrounding fluid.
This document presents details of the verification process of the RADTRAN computer code which was established for the calculation of risk estimates for radioactive materials transportation by highway, rail, air, and waterborne modes.
A ``debris-less`` laser-plasma source (LPS) of extreme-UV radiation has been developed by Kubiak, et al. This is a huge step forward for the extreme-UV lithography program (EUVL) because it will extend the life of the collecting mirrors that face the source. This source has a 300-{mu}m diameter (D source) which is larger than the earlier, {approximately}75-{mu}m diameter plasma balls created on metal targets. The larger source size requires that the Etendu of the system must also be larger if the source radiation is to be used efficiently. A family of 4-mirror, scanning, ring-field lithography cameras has been designed that can be efficiently coupled to a ``debris-less`` LPS. The most promising design has a 0.085-numerical aperture (NA{sub camera}) for printing {approx} 100-nm features. At the image plane it has 13 nm of distortion and a 98% Strehl ratio across its 7-mm wide ring-field ({Delta}r).
We report the effects of mirror doping and reflectivity in 850 and 780 nm oxide-confined vertical cavity surface emitting lasers. Decreased doping throughout the n-type mirror produces significantly higher quantum efficiency, while the optimum reflectivity is dependent upon the gain material.
The practical implementation of the surface micromachined microengine [1,2] to perform useful microactuation tasks requires a thorough understanding of the dynamics of the engine. This understanding is necessary in order to create appropriate drive signals, and to experimentally measure fundamental quantities associated with the engine system. We have developed and applied a dynamical model of the microengine and used it to accomplish three objectives: (1) drive inertial loads in a controlled fashion, i.e. specify and achieve a desired time dependent angular position of the output gear,( 2) minimize stress and frictional forces during operation, and (3) as a function of time, experimentally determine forces associated with the output gear, such as the load torque being applied to the output gear due to friction.
Model uncertainty, if ignored, can seriously degrade the performance of an otherwise well-designed control system. If the level of this uncertainty is extreme, the system may even be driven to instability. In the context of structural control, performance degradation and instability imply excessive vibration or even structural failure. Robust control has typically been applied to the issue of model uncertainty through worst-case analyses. These traditional methods include the use of the structured singular value, as applied to the small gain condition, to provide estimates of controller robustness. However, this emphasis on the worst-case scenario has not allowed a probabilistic understanding of robust control. In this paper an attempt to view controller robustness as a probability measure is presented. The probability of failure due to parametric uncertainty is estimated using first-order reliability methods (FORM). It is demonstrated that this method can provide quite accurate results on the probability of failure of actively controlled structures. Moreover, a comparison of this method to a suitability modified structured singular value robustness analysis in a probabilistic framework is performed. It is shown that FORM is the superior analysis technique when applied to a controlled three degree-of-freedom structure. In addition, the robustness qualities of various active control design schemes such as LQR, H{sub 2}, H {sub oo}, and {mu}-synthesis is discussed in order to provide some design guidelines.
The thermodynamic environment surrounding a heat-generating waste package can play an important role in the performance of a high-level radioactive waste repository. However, rigorous models of heat transfer are often compromised in near-drift simulations. Convection and radiation are usually ignored or approximated so that simpler conduction models can be used. This paper presents numerical simulations that explicitly model conduction, convection, and radiation in an empty drift following emplacement of a heat-generating waste package. Temperatures and relative humidities are determined at various locations within the drift. Comparisons are made between different models of heat transfer, and the relative effects of each heat transfer mode on the thermodynamic environment of the waste package are examined.
The Uranium Mill Tailings Remediation Action (UMTRA) Program is responsible for the assessment and remedial action at the 24 former uranium mill tailings sites located in the United States. The surface remediation phase, which has primarily focused on containment and stabilization of the abandoned uranium mill tailings piles, is nearing completion. Attention has now turned to the groundwater restoration phase. One alternative under consideration for groundwater restoration at UMTRA sites is the use of in-situ permeable reactive subsurface barriers. In this type of a system, contaminated groundwater will be allowed to flow naturally through a barrier filled with material which will remove hazardous constituents from the water by physical, chemical or microbial processes while allowing passage of the pore water. The subject of this report is a reactive barrier which would remove uranium and other contaminants of concern from groundwater by microbial action (i.e., a microbial barrier). The purpose of this report is to assess the current state of this technology and to determine issues that must be addressed in order to use this technology at UMTRA sites. The report focuses on six contaminants of concern at UMTRA sites including uranium, arsenic, selenium, molybdenum, cadmium and chromium. In the first section of this report, the fundamental chemical and biological processes that must occur in a microbial barrier to control the migration of contaminants are described. The second section contains a literature review of research which has been conducted on the use of microorganisms to immobilize heavy metals. The third section addresses areas which need further development before a microbial barrier can be implemented at an UMTRA site.
This publication is designed to inform present and potential customers and partners of the DOE Center of Excellence for the Synthesis and Processing of Advanced Materials about significant advances resulting from Center-coordinated research. The format is an easy-to-read, not highly technical, concise presentation of the accomplishments. Selected accomplishments from each of the Center`s seven initial focused projects are presented. The seven projects are: (1) conventional and superplastic forming; (2) materials joining; (3) nanoscale materials for energy applications; (4) microstructural engineering with polymers; (5) tailored microstructures in hard magnets; (6) processing for surface hardness; and (7) mechanically reliable surface oxides for high-temperature corrosion resistance.
The Smart Gun Technology Project has a goal to eliminate the capability of an unauthorized user from firing a law enforcement officer`s firearm by implementing {open_quote}smart{close_quote} technologies. Smart technologies are those that can in some manner identify an officer. This report will identify, describe, and grade various technologies as compared to the requirements that were obtained from officers. This report does not make a final recommendation for a smart gun technology, nor does it give the complete design of a smart gun system.
Numerical studies have been made of an infiltration experiment at Fran Ridge using the TOUGH2 code to aid in the selection of computational models for performance assessment. The exercise investigates the capabilities of TOUGH2 to model transient flows through highly fractured tuff and provides a possible means of calibration. Two distinctly different conceptual models were used in the TOUGH2 code, the dual permeability model and the equivalent continuum model. The infiltration test modeled involved the infiltration of dyed ponded water for 36 minutes. The 205 gallon filtration of water observed in the experiment was subsequently modeled using measured Fran Ridge fracture frequencies, and a specified fracture aperture of 285 {mu}m. The dual permeability formulation predicted considerable infiltration along the fracture network, which was in agreement with the experimental observations. As expected, minimal fracture penetration of the infiltrating water was calculated using the equivalent continuum model, thus demonstrating that this model is not appropriate for modeling the highly transient experiment. It is therefore recommended that the dual permeability model be given priority when computing high-flux infiltration for use in performance assessment studies.
This is a brochure about the Solar Thermal Design Assistance Center of Sandia National Laboratories: technical assistance, testing, technology development, education, and customer services
This small booklet tells the profile, mission, operations, services, and data base of Sandia National Laboratories Photovoltaic Design Assistance Center
Reactor power supplies offer many attractive characteristics for lunar surface applications. The Topaz II reactor resulted from an extensive development program in the former Soviet Union. Flight quality reactor units remain from this program and are currently under evaluation in the United States. This paper examines the potential for applying the Topaz II, originally developed to provide spacecraft power, as a lunar surface power supply.
In accordance with the Nuclear Regulatory Commission regulation regarding groundwater travel times at geologic repositories, various models of unsaturated flow in fractured tuff have been developed and implemented to assess groundwater travel times at the potential repository at Yucca Mountain, Nevada. Kaplan used one-dimensional models to describe the uncertainty and sensitivity of travel times to various processes at Yucca Mountain. Robey and Arnold et al. used a two-dimensional equivalent continuum model (ECM) with inter- and intra-unit heterogeneity in an attempt to assess fast-flow paths through the unsaturated, fractured tuff at Yucca Mountain (GWTT-94). However, significant flow through the fractures in previous models was not simulated due to the characteristics of the ECM, which requires the matrix to be nearly saturated before flow through the fractures is initiated. In the current study (GWTT-95), four two-dimensional cross-sections at Yucca Mountain are simulated using both the ECM and dual-permeability (DK) models. The properties of both the fracture and matrix domains are geostatistically simulated, yielding completely heterogeneous continua. Then, simulations of flow through the four cross-sections are performed using spatially nonuniform infiltration boundary conditions. Steady-state groundwater travel times from the potential repository to the water table are calculated.
The next total-system performance-assessment (TSPA) analyses are designed to aid DOE in performing an ``investment analysis`` for Yucca Mountain. This TSPA must try to bound the uncertainties for several issues that will contribute to the decision whether the US should proceed with the development of a nuclear-waste repository at Yucca Mountain. Because site-characterization experiments and data collection will continue for the foreseeable future, the next TSPA (called TSPA-IA) will again only be able to use partially developed models and partial data sets. In contrast to previous analyses however, TSPA-IA must address more specific questions to be of assistance to the investment-analysis deliberations.
Unsaturated flow has been modeled through four cross-sections at Yucca Mountain, Nevada, for the purpose of determining groundwater particle travel times from the potential repository to the water table. This work will be combined with the results of flow modeling in the saturated zone for the purpose of evaluating the suitability of the potential repository under the criteria of 10CFR960. One criterion states, in part, that the groundwater travel time (GWTT) from the repository to the accessible environment must exceed 1,000 years along the fastest path of likely and significant radionuclide travel. Sensitivity analyses have been conducted for one geostatistical realization of one cross-section for the purpose of (1) evaluating the importance of hydrological parameters having some uncertainty and (2) examining conceptual models of flow by altering the numerical implementation of the conceptual model (dual permeability (DK) and the equivalent continuum model (ECM). Results of comparisons of the ECM and DK model are also presented in Ho et al.
The performance of waste packages containing high-level nuclear wastes at underground repositories such as the potential repository at Yucca Mountain, Nevada, depends, in part, on the thermodynamic environment immediately surrounding the buried waste packages. For example, degradation of the waste packages can be caused by corrosive and microbial processes, which are influenced by both the relative humidity and temperature within the emplacement drifts. In this paper, the effects of conduction, convection, and radiation are investigated for a heat-generating waste package in an empty-drift. Simulations explicitly modeling radiation from the waste package to the drift wall are compared simulations using only conduction. Temperatures, relative humidities, and vapor mass fractions are compared at various locations within the drift. In addition, the effects of convection on relative humidity and moisture distribution within the drift are presented.
The Radiological Environment Modeling System (REMS) quantifies dose to humans in radiation environments using the IGRIP (Interactive Graphical Robot Instruction Program) and Deneb/ERGO (Ergonomics) simulation software products. These commercially available products are augmented with custom C code to provide the radiation exposure information to and collect the radiation dose information from the workcell simulations. The emphasis of this paper is on the IGRIP and Deneb/ERGO parts of REMS, since that represents the extension to existing capabilities developed by the authors. Through the use of any radiation transport code or measured data, a radiation exposure input database may be formulated. User-specified IGRIP simulations utilize these database files to compute and accumulate dose to human devices (Deneb`s ERGO human) during simulated operations around radiation sources. Timing, distances, shielding, and human activity may be modeled accurately in the simulations. The accumulated dose is recorded in output files, and the user is able to process and view this output. REMS was developed because the proposed reduction in the yearly radiation exposure limit will preclude or require changes in many of the manual operations currently being utilized in the Weapons Complex. This is particularly relevant in the area of dismantlement activities at the Pantex Plant in Amarillo, TX. Therefore, a capability was needed to be able to quantify the dose associated with certain manual processes so that the benefits of automation could be identified and understood.
A technique called the Natural Excitation Technique or has been developed to response extract response parameters from large operational structure when subjected to random and unmeasured forces such as wind, road noise, aerodynamics, or waves. Six applications of NExT to ambient excitation testing and NExT analysis are surveyed in this paper with a minimum of technical detail. In the first application, NExT was applied to a controlled-yaw Horizontal-Axis Wind Turbine (HAWT). By controlling the yaw degree of freedom an important class of rotating coordinate system effects are reduced. A new shape extraction procedure was applied to this data set with good results. The second application was to a free-yaw HAWT. The complexity of the response has prompted further analytical studies and the development of a specialized visualization package. The third application of NExT was to a parked three-bladed Vertical-Axis Wind Turbine (VAWT) in which traditional modal testing could not excite all modes of interest. The shape extraction process used cross-correlation functions directly in a time-domain shape-fitting routine. The fourth application was to ground transportation systems. Ongoing work to improve driver and passenger comfort in tractor-trailer vehicles and to refine automobile body and tire models will use NExT. NExT has been used to process ambient vibration data for Finite Element Model correlation and is being used to study Structural Health Monitoring with ambient excitation. Shape fitting was performed using amplitude and phase information taken directly from the cross-spectra. The final application is to an offshore structure. This work is on-going, however initial studies have found a high-modal density, high noise content, and sparse data set.
Future advances in the application of photonic interconnects will involve the insertion of parallel-channel links into Multi-Chip Modules (MCMS) and board-level parallel connections. Such applications will drive photonic link components into more compact forms that consume far less power than traditional telecommunication data links. These will make use of new device-level technologies such as vertical cavity surface-emitting lasers and special low-power parallel photoreceiver circuits. Depending on the application, these device technologies will often be monolithically integrated to reduce the amount of board or module real estate required by the photonics. Highly parallel MCM and board-level applications will also require simplified drive circuitry, lower cost, and higher reliability than has been demonstrated in photonic and optoelectronic technologies. An example is found in two-dimensional point-to-point array interconnects for MCM stacking. These interconnects are based on high-efficiency Vertical Cavity Surface Emitting Lasers (VCSELs), Heterojunction Bipolar Transistor (HBT) photoreceivers, integrated micro-optics, and MCM-compatible packaging techniques. Individual channels have been demonstrated at 100 Mb/s, operating with a direct 3.3V CMOS electronic interface while using 45 mW of electrical power. These results demonstrate how optoelectronic device technologies can be optimized for low-power parallel link applications.
Because of the complexity, volume of data and calculations required, one preferred analytical tool to perform transportation risk assessments is the RADTRAN computer code. RADTRAN combines user-determined material, packaging, transportation, demographic and meteorological factors, with health physics data to calculate expected radiological consequences and accident risk from transporting radioactive materials by all commercial modes including truck, rail, ship, air and barge. The computer code consists of two major modules for each transport mode: the incident-free module, in which doses from normal transport are calculated; and the accident module, in which dose consequences and probabilities are evaluated to generate risk estimates. The purpose of this presentation is to describe the development of a standardized procedure to perform transportation radiological risk assessments employing conventional spreadsheet programs to automate generation of RADTRAN input files and post-processing analysis of the resulting output.
This document presents details of the environmental activities that occurred during 1994 at Sandia National Laboratories. Topics include: Background about Sandia; radiation facts; sources of radiation; environmental monitoring; discussion of radiation detectors; radioactive waste management; environmental restoration; and quality assurance.
The mission of the American Textile (AMTEX{trademark}) Partnership is to engage the unique technical resources of the Department of Energy National Laboratories to work with the US Integrated Textile Complex (US ITC) and research universities to develop and deploy technologies that will increase the competitiveness of the US ITC. The objectives of the Demand Activated Manufacturing Architecture (DAMA) project of AMTEX are: (1) to determine strategic business structure changes for the US ITC; (2) to establish a textile industry electronic marketplace, (3) to provide methods for US ITC education ad implementation of an electronic marketplace. The Enterprise Modeling and Simulation Task of DAMA is focusing on the first DAMA goal as described in another paper of this conference. The Cooperative Business Management (CBM) Task of DAMA is developing computer-based tools that will render system-wide information accessible for improved decision making. Three CBM strategies and the associated computer tools being developed to support their implementation are described in this paper. This effort is addressing the second DAMA goal to establish a textile industry electronic marketplace in concert with the Connectivity and Infrastructure Task of DAMA. As the CBM tools mature, they will be commercialized through the DAMA Education, Outreach and Commercialization Task of DAMA to achieve the third and final DAMA goal.
The cost of repairing or replacing failed components depends on the number and timing of failures. Although the total probability of individual component failure is sometimes interpreted as the percentage of components likely to fail, this perception is often far from correct. Different amounts of common versus independent uncertainty can cause different numbers of components to be at risk of failure. The FAROW tool for fatigue and reliability analysis of wind turbines makes it possible for the first time to conduct a detailed economic analysis of the effects of uncertainty on fleet costs. By dividing the uncertainty into common and independent parts, the percentage of components expected to fail in each year of operation is estimated. Costs are assigned to the failures and the yearly costs and present values are computed. If replacement cost is simply a constant multiple of the number of failures, the average, or expected cost is the same as would be calculated by multiplying by the probability of individual component failure. However, more complicated cost models require a break down of how many components are likely to fail. This break down enables the calculation of costs associated with various probability of occurrence levels, illustrating the variability in projected costs. Estimating how the numbers of components expected to fail evolves over time is also useful in calculating the present value of projected costs and in understanding the nature of the financial risk.
The Aging Aircraft NDI Validation Center (AANC) was established by the Federal Aviation Administration Technical Center (FAATC) at Sandia National Laboratories in August of 1991. The goal of the AANC is to provide independent validation of technologies intended to enhance the structural inspection of aging commuter and transport aircraft. The deliverables from the AANC`s validation activities are assessments of the reliability of existing and emerging inspection technologies as well as analyses of the cost benefits to be derived from their implementation. This paper describes the methodology developed by the AANC to assess the performance of NDI techniques. In particular, an experiment being developed to evaluate corrosion detection devices will be presented. The experiment uses engineered test specimens, as well as complete aircraft test beds to provide metrics for NDI validation.
Sandia`s Institutional Plan is by necessity a large document. As their missions have grown and diversified over the past decades, the variety of technical and site activities has increased. The programs and activities described here cover an enormous breadth of scientific and technological effort--from the creation of new materials to the development of a Sandia-wide electronic communications system. Today, there are three major themes that greatly influence this work. First, every federally funded institution is being challenged to find ways to become more cost effective, as the US seeks to reduce the deficit and achieve a balanced federal spending plan. Sandia is evaluating its business and operational processes to reduce the overall costs. Second, in response to the Galvin Task Force`s report ``Alternative Futures for the Department of Energy National Laboratories``, Sandia and the Department of Energy are working jointly to reduce the burden of administrative and compliance activities in order to devote more of the total effort to their principal research and development missions. Third, they are reevaluating the match between their missions and the programs they will emphasize in the future. They must demonstrate that Sandia`s roles--in national security, energy security, environmental integrity, and national scientific and technology agenda support--fit their special capabilities and skills and thus ensure their place in these missions for the longer planning horizon. The following areas are covered here: Sandia`s mission; laboratory directives; programmatic activities; technology partnerships and commercialization; Sandia`s resources; and protecting resources and the community.
A new approach to product development is described that integrates various unit operations into a unified ``knowledge-base``. This knowledge-base is easily accessible to all members of the design team due to the advent of high performance and networking capabilities of today`s desktop computers. This permits rapid optimization of the product`s material, shape, and manufacturing processes that satisfy the customer`s performance requirements while maximizing economic return for the manufacturer.
The Department of Energy (DOE) has been developing a planning process for mixed low-level waste (MLLW) disposal in conjunction with the affected states for over two years and has screened the potential disposal sites from 49 to 15. A radiological performance evaluation was conducted on these fifteen sites to further identify their strengths and weaknesses for disposal of MLLW. Technical analyses are on-going. The disposal evaluation process has sufficiently satisfied the affected states` concerns to the point that disposal has not been a major issue in the consent order process for site treatment plans. Additionally, a large amount of technical and institutional information on several DOE sites has been summarized. The relative technical capabilities of the remaining fifteen sites have been demonstrated, and the benefits of waste form and disposal facility performance have been quantified. However, the final disposal configuration has not yet been determined. Additionally, the MLLW disposal planning efforts will need to integrate more closely with the low-level waste disposal activities before a final MLLW disposal configuration can be determined. Recent Environmental Protection Agency efforts related to the definition of hazardous wastes may also affect the process.
The growth of polycrystalline and amorphous aluminum-oxygen alloy films using electron-beam evaporation of Al in the presence of an O{sub 2} electron-cyclotron-resonance (ECR) plasma was investigated for film compositions varying from 40% Al (Al{sub 2}O{sub 3}) to near 100% Al (AlO{sub x}). Processing parameters such as deposition temperature and ion energy were varied to study their effects on surface texture and film microstructure. The Al-rich films (AlO{sub x}) contain polycrystalline fcc Al grains with finely dispersed second-phase particles of {gamma}-Al{sub 2}O{sub 3} (1-2 nm in size). The surface roughness of these films was measured by atomic force microscopy and found to increase with sample bias and deposition temperature. Stoichiometric Al{sub 2}O{sub 3} films grown at 100{degrees}C and 400{degrees}C without an applied bias were amorphous, while an applied bias of -140 V formed a nanocrystalline {gamma}-Al{sub 2}O{sub 3} film at 400{degrees}C. The surface roughness of the Al{sub 2}O{sub 3} increased with temperature while ion irradiation produced a smoother surface.
Sandia National Laboratories` (SNL) Technical Library is now responsible for providing citation verification management support for all references cited in technical reports issued by the Nuclear Waste Management (NWM) Program. This paper dancing how this process is managed for the Yucca Mountain Site Characterization (YWP), Waste Isolation Pilot Plant (WIPP), Idaho National Engineering Laboratory (INEL), and Greater Confinement Disposal (GCD) projects. Since technical reports are the main product of these projects, emphasis is placed on meeting the constantly evolving needs of these customers in a timely and cost-effective manner.
Various applications are currently motivating interest in the transmission of very high laser intensities through optical fibers. As intensities within a fiber are increased, however, laser breakdown or laser-induced fiber damage will eventually occur and interrupt fiber transmission. For a number of years we have been studying these effects during the transmission of Q-switched, Nd/YAG laser pulses through step-index, multimode, fused-silica fiber. We have found that fiber transmission is often limited by a plasma-forming breakdown occurring at the fiber entrance face. This breakdown results in subtle surface modifications that can leave the surface more resistant to further breakdown or damage events. Catastrophic fiber damage can also occur as a result of a number of different mechanisms, with damage appearing at fiber end faces, within the initial ``entry`` segment of the fiber path, and at other internal sites due to effects related to the particular fiber routing. An overview of these past observations is presented, and issues requiring further study are identified.
A long standing problem in low-temperature plasma discharge physics is to understand in detail the mutual interaction of real exposed surfaces (electrodes) with the reactive plasma environment. In particular, one wishes to discern the influence of these surfaces on the plasma parameters given their contributions from secondary electrons and ions. This paper briefly reviews the known surface interaction processes as well as currently available diagnostics to study the interface between plasmas and surfaces. Next comes a discussion describing the application of plasma-modulated electroreflectance to this research and some potential experimental techniques.
Low-energy deposition of Al(O) alloys from an electron cyclotron resonance (ECR) plasma offers a scaleable method for the synthesis of thick, high-strength Al layers. This work compares alloy layers formed by an ECR-0{sub 2} plasma in conjunction with Al evaporation to 0-implanted Al (ion energies 25-200 keV); and it examines the effects of volume fraction of A1{sub 2}0{sub 3} phase and deposition temperature on the yield stress of the material. TEM showed the Al(O) alloys contain a dense dispersion of small {gamma}-Al{sub 2}0{sub 3} precipitates ({approximately}l nm) in a fine-grain (10-100 nm) fcc Al matrix when deposited at a temperature of {approximately}100C, similar to the microstructure for gigapascal-strength 0-implanted Al. Nanoindentation gave hardnesses for ECR films from 1.1 to 3.2 GPa, and finite-element modeling gave yield stresses up to 1.3 {plus_minus} 0.2 GPa with an elastic modulus of 66 GPa {plus_minus} 6 GPa (similar to pure bulk Al). The yield stress of a polycrystalline pure Al layer was only 0.19 {plus_minus} 0.02 GPa, which was increased to 0.87 {plus_minus} 0.15 GPa by implantation with 5 at. % 0.
A method is described for generating electron cross sections that are compatible with standard discrete ordinates codes without modification. There are many advantages of using an established discrete ordinates solver, e.g. immediately available adjoint capability. Coupled electron-photon transport capability is needed for many applications, including the modeling of the response of electronics components to space and man-made radiation environments. The cross sections have been successfully used in the DORT, TWODANT and TORT discrete ordinates codes. The cross sections are shown to provide accurate and efficient solutions to certain multidimensional electronphoton transport problems.
Several effects of seismic activity on the release of radionuclides from a potential repository at Yucca Mountain are quantified. Future seismic events are predicted using data from the seismic hazard analysis conducted for the Exploratory Studies Facility (ESF). Phenomenological models are developed, including rockfall (thermal-mechanical and seismic) in unbackfilled emplacement drifts, container damage caused by fault displacement within the repository, and flow-path chance caused by changes in strain. Using the composite-porosity flow model (relatively large-scale, regular percolation), seismic events show little effect on total-system releases; using the weeps flow model (episodic pulses of flow in locally saturated fractures), container damage and flow-path changes cause over an order of magnitude increase in releases. In separate calculations using, more realistic representations of faulting, water-table rise caused by seismically induced changes in strain are seen to be higher than previously estimated by others, but not sufficient to reach a potential repository.
Development of a vapor generator for consistently producing accurate amounts of vapor from low vapor pressure explosive materials is a pressing need within the explosives detection community. Of particular importance for reproducibility and widespread acceptance of results is the correlation of such a vapor generator to a National Institute of Standards and Technology (NIST) mass standard. This paper describes an explosives vapor generator recently developed at Varian in which a solid explosive sample in a precision bore glass tube is put in an oven at constant temperature, and vapor diff-using from the top of the tube is entrained in a carrier gas flow. The rate of vapor output is thus dependent on both the equilibrium vapor pressure of the solid at oven temperature and the rate of diffusion up the length of the tube. Correlation to a NIST mass standard is achieved by periodic weighing of the sample tube on a microbalance. We report results obtained with the explosives TNT and RDX. Results for TNT show that the mass output rate is constant over hundreds of hours of continuous use, with outputs of {approximately} 10--2000 pg/sec for oven temperatures in the range of 60--120{degrees}C. Both the mass loss experiments and calibration with an ion mobility spectrometer (IMS) give a TNT mass output value of 85 pg/sec at 79{degrees}C, and this result is supported by transport theory calculations. Mass loss curves for RDX are also linear with time, and show the expected exponential increase of mass output with oven temperature.
This paper presents an implemented algorithm that automatically designs fixtures and assembly pallets to hold three-dimensional parts. The designed fixtures rigidly constrain and locate the part, obey task constraints, are robust to part shape variations, are easy to load, and are economical to produce. The algorithm is guaranteed to find the global optimum solution that satisfies these and other pragmatic conditions. We present the results of the algorithm applied to several practical manufacturing problems. For these complex problems the algorithm typically returns initial high-quality fixture designs in less than two minutes, and identifies th global optimum design in just over an hour.
Multichip modules (MCMs) containing power components need a substrate with excellent heat spreading capability both to avoid hot spots and to move dissipated heat toward the system heat sinks. Polycrystalline diamond is an excellent MCM heat spreading substrate but remains several orders of magnitude too expensive and somewhat more difficult to process than conventional mother-board materials. Today`s power MCMs concentrate on moderately priced silicon wafers and aluminum nitride ceramic with their improved thermal conductivity and good thermal expansion match to power semiconductor components, in comparison to traditional alumina and printed wiring board materials. However, even silicon and AlN substrates are challenged by designers` thermal needs. We report on the fabrication of micro-heat pipes embedded in silicon MCM substrates (5{times}5 cm) by the use of micromachined capillary wick structures and hermetic micro-cavities. This passive microstructure results in more than a 5 times improvement in heat spreading capability of the silicon MCM substrate over a large range of power densities and operating temperatures as compared with silicon alone. Thus diamond-like cooling is possible at silicon prices.
This paper describes a study in which HTML style guides were characterized, compared to established HCI style guides, and evaluated against findings from HCI reviews of web paces and applications. Findings showed little consistency among the 21 HTML style guides assessed, with 75% of recommendations appearing in only one style guide. While there was some overlap, only 20% of HTML relevant recommendations from established style guides were found in HTML style guides. HTML style guides emphasized common look and feel, information display, and navigation issues with little mention of many issues prominent in established style guides such as help, message boxes and data entry. This difference is reinforced by other results showing that HTML style guides addressed concerns of web information content pages with much greater success than web-based applications. It is concluded that while the WWW represents a unique HCI environment, development of HTML style guides has been less rigorous, with issues associated with web-based applications largely ignored.
Piezoelectric actuators provide high frequency, force, and stiffness capabilities along with reasonable Stroke limits, all of which can be used to increase performance levels in precision manufacturing systems. This paper describes two examples of embedding piezoelectric actuators in structural components for vibration control. One example involves suppressing the self excited chatter phenomenon in the metal cutting process of a milling machine and the other involves damping vibrations induced by rigid body stepping of a photolithography platen. Finite element modeling and analyses are essential for locating and sizing the actuators and permit further simulation studies of the response of the dynamic system. Experimental results are given for embedding piezoelectric actuators in a cantilevered bar configuration, which was used as a surrogate machine tool structure. These results are incorporated into a previously developed milling process simulation and the effect of the control on the cutting process stability diagram is quantified. Experimental results are also given for embedding three piezoelectric actuators in a surrogate photolithography platen to suppress vibrations. These results demonstrate the potential benefit that can be realized by applying advances from the field of adaptive structures to problems in precision manufacturing.
Electron cyclotron resonance (ECR) etching of GaN in Cl{sub 2}/H{sub 2}/Ar, C1{sub 2}/SF{sub 6}/Ar, BCl{sub 3}/H{sub 2}/Ar and BCl{sub 3}/SF{sub 6}/Ar plasmas is reported as a function of percent H{sub 2} and SF{sub 6}. GaN etch rates were found to be 2 to 3 times greater in Cl{sub 2}/H{sub 2}/Ar discharges than in BCl{sub 3}/H{sub 2}/Ar discharges independent of the H{sub 2} concentration. In both discharges, the etch rates decreased as the H{sub 2} concentration increased above 10%. When SF{sub 6} was substituted for H{sub 2}, the GaN etch rates in BCl{sub 3}-based plasmas were greater than those for the Cl{sub 2}-based discharges as the SF{sub 6} concentration increased. GaN etch rates were greater in Cl{sub 2}/H{sub 2}/Ar discharges as compared to Cl{sub 2}SF{sub 6}/Ar discharges whereas the opposite trend was observed for BCl{sub 3}-based discharges. Variations in surface morphology and near-surface stoichiometry due to plasma chemistries were also investigated using atomic force microscopy and Auger spectroscopy, respectively.
VICTORIA-92 is a mechanistic computer code for analyzing fission product behavior within the reactor coolant system (RCS) during a severe reactor accident. It provides detailed predictions of the release of radionuclides and nonradioactive materials from the core and transport of these materials within the RCS. The modeling accounts for the chemical and aerosol processes that affect radionuclide behavior. Coupling of detailed chemistry and aerosol packages is a unique feature of VICTORIA; it allows exploration of phenomena involving deposition, revaporization, and re-entrainment that cannot be resolved with other codes. The purpose of this work is to determine the attenuation of fission products in the RCS and on the secondary side of the steam generator in an accident initiated by a steam generator tube rupture (SGTR). As a class, bypass sequences have been identified in NUREG-1150 as being risk dominant for the Surry and Sequoyah pressurized water reactor (PWR) plants.
When assembling a product, humans, robots, and other automation employ a variety of tools to manipulate, attach, and test parts and subassemblies. This paper proposes a framework lo represent and reason about geometric accessibility constraints for a wide variety of assembly tools. Central to the framework is a use volume encoding a minimum space that must be free in an assembly state to apply a given tool, and placement constraints on where that volume must be placed relative to the parts on which the tool acts. Determining whether a tool can be applied in a given assembly state is an instance of the FINDPLACE problem. In addition, we present more efficient methods lo integrate the framework into assembly planning. For tools that are applied either before or after their target parts are mated, one method preprocesses a single tool application for all possible states of assembly of a product. For tools applied after their target parts are mated, a complementary method guarantees polynomial-time assembly planning. We describe experiments with an initial implementation of the framework and a library of seven tools.
In a virtual environment with multiple participants, it is necessary that the user`s actions be replicated by synthetic human forms. Whole body digitizers would be the most realistic solution for capturing the individual participant`s human form, however the best of the digitizers available are not interactive and are therefore not suitable for real-time interaction. Usually, a limited number of sensors are used as constraints on the synthetic human form. Inverse kinematics algorithms are applied to satisfy these sensor constraints. These algorithms result in slower interaction because of their iterative nature, especially when there are a large number of participants. To support real-time interaction in a virtual environment, there is a need to generate closed for solutions and fast searching algorithms. In this paper, a new closed form solution for the arms (and legs) is developed using two magnetic sensors. In developing this solution, we use the biomechanical relationship between the lower arm and the upper arm to provide an analytical, non-iterative solution, We have also outlined a solution for the whole human body by using up to ten magnetic sensors to break the human skeleton into smaller kinematic chains. In developing our algorithms, we use the knowledge of natural body postures to generate faster solutions for real-time interaction.
The underlying report for this paper evaluates options for using depleted uranium as shielding materials for transport systems for disposal of vitrified high-level waste (VHLW). In addition, economic analyses are presented to compare costs associated with these options to costs, associated with existing and proposed storage, transport, and diposal capabilities. A more detailed evaluation is provided elsewhere. (Yoshimura et al. 1995.)
This paper discusses the core damage frequency (CDF) insights gained by analyzing the results of the Individual Plant Examinations (IPES) for two groups of plants: boiling water reactor (BWR) 3/4 plants with Reactor Core Isolation Cooling systems, and Westinghouse 4-loop plants. Wide variability was observed for the plant CDFs and for the CDFs of the contributing accident classes. On average, transients-with loss of injection, station blackout sequences, and transients with loss of decay heat removal are important contributors for the BWR 3/4 plants, while transients, station blackout sequences, and loss-of-coolant accidents are important for the Westinghouse 4-loop plants. The key factors that contribute to the variability in the results are discussed. The results are often driven by plant-specific design and operational characteristics, but differences in modeling approaches are also important for some accident classes.
Local public opposition to federal bureaucratic decisions has resulted in public agencies rethinking the role of stakeholders in decision making. Efforts to include stakeholders directly in the decision-making process are on the increase. Unfortunately, many attempts to involve members of the public in decisions involving complex technical issues have failed. A key problem has been defining a meaningful role for the public in the process of arriving at a technical decision. This paper describes a successful effort by Sandia National Laboratories (SNL) in New Mexico to involve stakeholders in an important technical decision associated with its Environmental Restoration (ER) Project. The decision was where to locate a Corrective Action Management Unit (CAMU), a facility intended to consolidate and store wastes generated from the cleanup of hazardous waste sites. A formal priority setting process known as the Laboratory Integration Prioritization System (LIPS) was adapted to provide an approach for involving the public. Although rarely applied to stakeholder participation, the LIPS process proved surprisingly effective. It produced a consensus over a selected site and enhanced public trust and understanding of Project activities.
System Certification is a regulatory concept which is intended to expand the scope of radioactive material transport regulations by allowing alternative means for proving compliance with the requisite standards of safety set out in transport regulations. In practice it may allow more stringent requirements in one aspect of the regulations to be substituted for less stringent application in other areas so long as the safety standard provided by regulation is preserved. The concept is widely perceived as the imposition of operational controls in exchange for relaxation of packaging standards, but that is only one possibility in the spectrum of potential actions under a System Certification provision in IAEA or national regulations.
Sandia has made considerable progress in the past year on the MELCOR code for integrated severe nuclear reactor accident analysis. Actinities for the past year are presented.
The design and analysis of a high brightness electron beam experiment under construction at Sandia National Laboratory is presented. The beam energy is 12 MeV, the current 35-40 kA, the rms radius 0.5 mm, and the pulse duration FWHM 40 ns. The accelerator is SABRE a pulsed inductive voltage adder, and the electron source is a magnetically immersed foilless diode. This experiment has as its goal to stretch the technology to the edge and produce the highest possible electron current in a submillimeter radius beam.
The quality assurance requirements that apply to the effort to achieve safe transportation, storage, and disposal of high-level nuclear waste specify that ``design control`` be applied to design activities. That effort also involves extensive scientific investigation activities to, among other things, develop information that may be used in engineering design activities. Individuals who are charged with the implementation of such quality assurance requirements have come to a variety of conclusions about whether there is any firm linkage between design control and the conduct of scientific investigations. This paper contends that there is a reasonable and necessary linkage between ``design control`` and scientific activities, though not a connection that has traditionally been made and not one addressed in the QA standards for radioactive waste management programs.
The III-V nitride-containing semiconductors InN, GaN, and AIN and their ternary alloys are the focus of extensive research for application to visible light emitters and as the basis for high temperature electronics. Recent advances in ion implantation doping of GaN and studies of the effect of rapid thermal annealing up to 1100{degrees}C are making new device structures possible. Both p- and n-type implantation doping of GaN has been achieved using Mg co-implanted with P for p-type and Si-implantation for n-type. Electrical activation was achieved by rapid thermal anneals in excess of 1000{degrees}C. Atomic force microscopy studies of the surface of GaN after a series of anneals from 750 to 1100{degrees}C shows that the surface morphology gets smoother following anneals in Ar or N{sub 2}. The photoluminescence of the annealed samples also shows enhanced bandedge emission for both annealing ambients. For the deep level emission near 2.2 eV, the sample annealed in N{sub 2} shows slightly reduced emission while the sample annealed in Ar shows increased emission. These annealing results suggest a combination of defect interactions occur during the high temperature processing.
Inclusion of renewable energy sources in national and international energy strategies is a key component of a viable global energy future. The global energy balance is going to shift radically in the near future brought about by significant increases in population in China and India, and increases in the energy intensity of developing countries. To better understand the consequences of such global shifts in energy requirements and to develop appropriate energy strategies to respond to these shifts, we need to look at the factors driving choices among supply options by geopolitical consumers and the impact these factors can have on the future energy mix.
High-speed optoelectronic modulators are becoming increasingly important in microwave applications. These devices are necessarily electrically large and hence require velocity matching of the microwave signal to the light. A design methodology for velocity matched electrodes on doped semiconductor devices will be presented. As an example of a successful device design, experimental results on a >10 bandwidth high-efficiency (>15{degrees}/V/mm) Mach Zehnder interferometer will be presented.
Articles in this issue include ``Molten salt corrosion testing,`` ``Pulsed ion beams for thermal surface treatment: Improved corrosion, wear, and hardness properties at low cost,`` ``Unmasking hidden armaments: Superconducting gravity sensor could find underground weapons, bunkers,`` ``Charbroiled burgers, heterocyclic amines, and cancer: Molecular modeling identifies dangerous mutagens,`` ``Revolutionary airbag offers increased safety options,`` ``EcoSys{sup TM}: an expert system for `Green Design` ``, ``Sandia, salt, and oil: Labs` diagnostics and analysis help maintain vital US oil reserve,`` and ``Automated fixture design speeds development for prototypes and production``.
Drilling is ubiquitous in oil, gas, geothermal, minerals, water well, and mining industries. Drilling and well completion account for 25% to 50% of the cost of producing power from geothermal energy. Reduced drilling costs will reduce the cost of electricity produced from geothermal resources. Undoubtedly, there are concepts for advanced drilling systems that have yet to be studied. However, the breadth and depth of previous efforts in this area almost guarantee that any new efforts will at least initially build on an idea or a variation of an idea that has already been investigated. Therefore, a review of previous efforts, coupled with a characterization of viable advanced drilling systems and the current state of technology as it applies to those systems, provide the basis for this study.
In order to understand and evaluate materials for use in Li ion rechargeable battery electrodes, we have modeled the crystal structures of various Mn oxide and Li Mn oxide compounds. We have modeled the MnO{sub 2} polymorphs and several spinels with intermediate compositions based on the amount of Li inserted into the tetrahedral site. 3-D representations of the structures provide a basis for identifying site occupancies, coordinations, Mn valence, order-disorder, and potentially new dopants for enhanced cathode behavior. XRD simulations of the crystal structures provide good agreement with observed patterns for synthesized samples. Ionic modeling of these materials consists of an energy minimization approach using Coulombic, repulsive, and van der Waals interactions. Modeling using electronic polarizabilities (shell model) allows a systematic analysis of changes in lattice energy, cell volume, and the relative stability of doped structures using ions such as Al, Ti, Ni, and Co.
Several novel polysilanes synthesized by the free-radical hydrosilation of oligomeric polyphenylsilane or poly(p-tert- butylphenylsilane) were examined for lithographic behavior. This recently developed route into substituted polysilanes has allowed for the rational design of a variety of polysilanes with a typical chemical properties such as alcohol and aqueous base solubility. Many of the polysilane resists made could be developed in aqueous sodium carbonate and bicarbonate solutions. These materials represent environmentally friendly polysilane resists in both their synthesis and processing.
Results from a chamber study to characterize emissions from combustion of selected pure energetic materials are presented in this paper. The study was carried out as a part of a comprehensive air pathways risk assessment for a propellant and explosive manufacturing facility that engages in open burning methods for manufacturing waste disposal. Materials selected for emissions characterization in this study included both aluminized and non-aluminized composite propellant, a double base propellant and a plastic bonded explosive. Combustion tests in a specialized chamber revealed very low emissions for gaseous products of incomplete combustion such as carbon monoxide and nitrogen oxides. Analysis of gaseous and aerosol emission products for a pre-selected target analyte list that included both volatile and semi-volatile organics revealed either low or non-detectable emissions for the four energetic types tested. Hydrogen chloride was detected as a major emission product from propellants containing ammonium perchlorate. Results from this work reveal that about one-half of the chlorine in the original material is released as hydrogen chloride. Based on earlier work, the balance of the chlorine emissions is expected to be in the form of chlorine gas.
Analysis of processes used for the production of single crystal turbine components reveals significant shortcomings. Inadequate consideration has been made of the fact the system is cooling dominated and that the amount of cooling tends to increase as the emissive cooling area expands during the process. Experimental evidence suggests that during processing, this increased cooling causes the solidification interface to move away from the baffle and become curved. The motion of the interface results in a decrease in the solidification gradient. The combination of these actions can result in variations in PDAS (primary dendrite arm spacing), grain misalignment and the production of defects. It is shown that despite this tendency, microstructural stabilization may be achieved through the use of the heat of fusion as an internal process heat source.
We present calculations of the specific contact resistance for metals to GaN. The calculations include a correct determination of the Fermi level taking into account the effect of the degenerate doping levels, required in creating tunneling ohmic contacts. Using a recently reported improved WKB approximation suitable in representing the depletion width at the metal-semiconductor interface, and a two band k-p model for the effective masses, specific contact resistance was determined as a function of doping concentration. The specific contact resistance was calculated using the best data available for barrier heights, effective masses and dielectric coefficients for GaN. Because the barrier height at the metal-semiconductor interface has a very large effect on the contact resistance and the available data is sketchy or uncertain, the effect of varying the barrier height on the calculated specific contact resistance was investigated. Further, since the III-V nitrides are being considered for high temperature device applications, the specific contact resistance was also determined as a function of temperature.
Lost circulation is a persistent problem in geothermal drilling and often accounts for a significant fraction of the cost of drilling a typical geothermal well. The US Department of Energy sponsors work at Sandia National Laboratories to develop technology for reducing lost circulation costs. This paper describes a downhole tool that has been developed at Sandia for improving the effectiveness and reducing the cost of cementing operations used to treat lost circulation zones. This tool, known as the drillable straddle packer, is a low-cost, disposable assembly used for isolating a loss zone and directing the flow of cement into the zone. This paper describes the tool concept, hardware design, deployment procedure, laboratory testing, and technical issues addressed during the development process.
Variation of model size as determined by grid density is studied for both model refinement and damage detection. In model refinement 3 it is found that a large model with a fine grid is preferable in order to achieve a reasonable correlation between the experimental response and the finite element model. A smaller model falls victim to the inaccuracies of the finite element method. As the grid become increasing finer, the FE method approaches an accurate representation. In damage detection the FE method is only a starting point. The model is refined with a matrix method which doesn`t retain the FE approximation, therefore a smaller model that captures most of the dynamics of the structure can be used and is preferable.
This paper presents a high bandwidth fiber-optic communication system intended for post accident recovery of weapons. The system provides bi-directional multichannel, and multi-media communications. Two smaller systems that were developed as direct spin-offs of the larger system are also briefly discussed.
To model the shock-induced behavior of porous or damaged energetic materials, a nonequilibrium mixture theory has been developed and incorporated into the shock physics code, CTH. Foundation for this multiphase model is based on a continuum mixture formulation given by Baer and Nunziato. In this nonequilibrium approach, multiple thermodynamic and mechanics fields are resolved including the effects of material relative motion, rate-dependent compaction, drag and heat transfer interphase effects and multiple-step combustion. Benchmark calculations are presented which simulate low-velocity piston impact on a propellant porous bed and experimentally-measured wave features are well replicated with this model. This mixture model introduces micromechanical models for the initiation and growth of reactive multicomponent flow which are key features to describe shock initiation and self-accelerated deflagration-to-detonation combustion behavior. To complement one-dimensional simulation, two dimensional numerical simulations are presented which indicate wave curvature effects due to the loss of wall confinement.
This contribution presents some lessons learned in the development of cooperation and knowledge transfer across the numerous interfaces involved in managing a corporate research laboratory.
Understanding the mechanical behavior of jointed-rock masses is of critical importance to designing and predicting the performance of a potential nuclear waste repositiry. To this end we have studied the frictional sliding between simulated rock joints using phase shifting moire interferometry. Preliminary calibration models were made from stacks of Lexan plates that were sand-blasted to provide a uniform frictional interface. Load was applied monotonically and phase shifted moire fringe patterns were recorded at three different load states. Plots of slip along the interfaces for the model are presented to demonstrate the ability of the photomechanics technique to provide precise measurements of in-plane displacement, and ultimately the slip between the plates.
Computational models for the July, 1994 collision of comet Shoemaker-Levy 9 with Jupiter have provided a framework for interpreting the observational data. Imaging, photometry, and spectroscopy data from ground-based, Hubble Space Telescope, and Galileo spacecraft instruments are consistent with phenomena that were dominated by the generation of incandescent fireballs that were ballistically ejected to high altitudes, where they formed plumes that subsequently collapsed over large areas of Jupiter`s atmosphere. Applications of similar computational models to collisions into Earth`s atmosphere show that a very similar sequence of events should take place for NEO impacts with energies as low as 3 megatons, recurring on 100 year timescales or less. This result suggests that the 1908 Tunguska event was a plume-forming atmospheric explosion, and that some of the phenomena associated with it might be related to the ejection and collapse of a high plume. Hazards associated with plume growth and collapse should be included in the evaluation of the impact threat to Earth, and opportunities should be sought for observational validation of atmospheric impact models by exploiting data already being collected from the natural flux of multi-kiloton to megaton sized objects that constantly enter Earth`s atmosphere on annual to decadal timescales.
The impact of Comet Shoemaker-Levy 9 on Jupiter in July, 1994, was the largest, most energetic impact event on a planet ever witnessed. Because it broke up during a close encounter with Jupiter in 1992, it was bright enough to be discovered more than a year prior to impact, allowing the scientific community an unprecedented opportunity to assess the effects such an event would have. Many excellent observations were made from Earth-based telescopes, the Hubble Space Telescope (HST) and the Galileo spacecraft en route to Jupiter. In this paper, these observations are used in conjunction with computational simulations performed with the CTH shock-physics hydrocode to determine the sizes of the fifteen fragments that made discernible impact features on the planet. To do this, CTH was equipped with a radiative ablation model and a post-processing radiative ray-trace capability that enabled light-flux predictions (often called the impact flash) for the viewing geometries of Galileo and ground-based observers. The five events recorded by Galileo were calibrated to give fragment size estimates. Compared against ground-based and HST observations, these estimates were extended using a least-squares analysis to assess the impacts of the remaining ten fragments. Some of the largest impacts (L, G and K) were greater that 1 km in diameter but the density of the fragments was low, about 0.25 g/cm{sup 3}. The volume of the combined fifteen fragments would make a sphere 1.8 km in diameter. Assuming a pre-breakup density of 0.5 g/cm{sup 3}, the parent body of Shoemaker-Levy 9 had a probable diameter of 1.4 km. The total kinetic energy of all the impacts was equivalent to the explosive yield of 300 Gigatons of TNT.
This contribution addresses requirements for ATM signaling channel authentication. Signaling channel authentication is an ATM security service that binds an ATM signaling message to its source. By creating this binding, the message recipient, and even a third party, can confidently verify that the message originated from its claimed source. This provides a useful mechanism to mitigate a number of threats. For example, a denial of service attack which attempts to tear-down an active connection by surreptitiously injecting RELEASE or DROP PARTY messages could be easily thwarted when authenticity assurances are in place for the signaling channel. Signaling channel authentication could also be used to provide the required auditing information for accurate billing which is impervious to repudiation. Finally, depending on the signaling channel authentication mechanism, end-to-end integrity of the message (or at least part of it) can be provided. None of these capabilities exist in the current specifications.
Crystal lattices are infinite periodic graphs that occur naturally in a variety of geometries and which are of fundamental importance in polymer science. Discrete models of protein folding use crystal lattices to define the space of protein conformations. Because various crystal lattices provide discretizations of the same physical phenomenon, it is reasonable to expect that there will exist ``invariants`` across lattices that define fundamental properties of protein folding process; an invariant defines a property that transcends particular lattice formulations. This paper identifies two classes of invariants, defined in terms of sublattices that are related to the design of algorithms for the structure prediction problem. The first class of invariants is, used to define a master approximation algorithm for which provable performance guarantees exist. This algorithm can be applied to generalizations of the hydrophobic-hydrophilic model that have lattices other than the cubic lattice, including most of the crystal lattices commonly used in protein folding lattice models. The second class of invariants applies to a related lattice model. Using these invariants, we show that for this model the structure prediction problem is intractable across a variety of three-dimensional lattices. It`` turns out that these two classes of invariants are respectively sublattices of the two- and three-dimensional square lattice. As the square lattices are the standard lattices used in empirical protein folding` studies, our results provide a rigorous confirmation of the ability of these lattices to provide insight into biological phenomenon. Our results are the first in the literature that identify algorithmic paradigms for the protein structure prediction problem which transcend particular lattice formulations.
Approximately 13% by volume of the US Department of Energy (DOE) current backlog of radioactive waste is characterized as high-level waste. Transportation of these wastes requires that the waste package have adequate shielding against gamma radiation. This project investigates the radiation shielding performance of titanium and depleted uranium, which have been proposed for use as gamma shielding materials in DOE transportation packages, by experimentally determining their buildup factors. Buildup factors are important in shield heating and radiation damage calculations. A point-isotropic-source type of buildup factor is the most useful for application in the point-kernal approach utilized in many simple shielding codes. The point-kernal method provides reasonable results for cases in which the shield is made of one solid material and the source can be approximated as one homogeneous material. The point-kernal method has been incorporated into a large number of shielding codes treating three-dimensional geometry using buildup factor data in some form. Buildup factors vary with a number of parameters such as the distance of penetration through the attenuating medium; the geometric configuration of the attenuating medium, source and detector position; the composition of the medium; the detector response function; and the energy and direction of emission of the source photons, ideally taken to be monoenergetic and isotropic.
It is likely that the ongoing process to produce the 1996 version of the IAEA Regulation for the Safe Transport of Radioactive Materials, IAEA Safety Series 6(SS 6) will result in a more stringent package qualification standard for air transport of large quantities of radioactive materials (RAM) than is included in the 1990 version. During the process to define the scope of the new requirements there was extensive discussion of their impact on, and application to, fissile material package qualification criteria. Since fissile materials are shipped in a variety of packaging ranging from exempt to Type B, each packaging of each type must be evaluated for its ability to maintain subcriticality both alone and in arrays and in both damaged and undamaged condition. In the 1990 version of SS 6 "damaged" means the condition of a package after it had undergone the "tests for demonstrating the ability to withstand accident conditions in transport," i.e., Type B qualification tests. These tests conditions are typical of severe accidents in surface modes but are less severe than air mode qualification test environments to be applied to Type C packages. As a result, questions arose about the need for a corresponding change in the 1996 SS 6 to define "damaged" to include the Type C test regime for criticality evaluations of fissile packages in air transport.
Intense, pulsed ion beams were used to melt and rapidly resolidify Types 316F, 316L and sensitized 304 stainless steel surfaces to eliminate the negative effects of microstructural heterogeneity on localized corrosion resistance. Anodic polarization curves determined for 316F and 316L showed that passive current densities were reduced and pitting potentials were increased due to ion beam treatment. Type 304 samples sensitized at 600°C for 100 h showed no evidence of grain boundary attack when surfaces were ion beam treated. Equivalent ion beam treatments were conducted with a 6061-T6 aluminum alloy. Electrochemical impedance experiments conducted with this alloy exposed to an aerated chloride solution showed that the onset of pitting was delayed compared to untreated control samples.
Inorganic polycrystalline hydrotalcite, Li2[Al2(OH)6]2·CO3·3H2O, coatings can be formed on aluminum and aluminum alloys by exposure to alkaline lithium carbonate solutions. This process is conducted using methods similar to traditional chromate conversion coating procedures, but does not use or produce toxic chemicals. The coating provides anodic protection and delays the onset of pitting during anodic polarization. Cathodic reactions are also inhibited which may also contribute to corrosion protection. Recent studies have shown that corrosion resistance can be increased by sealing hydrotalcite coated surfaces to transition metal salt solutions including Ce(NO3)3, KMnO4 and Li2MoO4. Results from these studies are also reported.
Water determination in semiconductor process gases is desirable in order to extend the life of gas delivery systems and improve wafer yields. We review our work in applying Fourier transform infrared spectroscopy to this problem, where a 10 ppb detection limit has been demonstrated for water in N2, HCl, and HBr. The potential for optical determination of other contaminants in these gases is discussed. Also, alternative optical spectroscopic approaches are briefly described. Finally, we discuss methods for dealing with interference arising from water in the instrument beam path, yet outside the sample cell.
Liquid properties are measured from the changes they induce in the resonant frequency and damping of thickness-shear mode quartz resonators. A smooth-surfaced resonator viscously entrains the contacting fluid and responds to the density-viscosity product. Separation of density and viscosity is accomplished using two devices: one with a smooth surface and one with a corrugated surface that traps fluid. By observing the difference in stored and dissipated energies in the contacting fluid, its non-Newtonian characteristics can also be determined.
This paper reviews the evolution of polymer electrolytes from the conventional PEO-LiX salt complexes to the more conducting polyphosphazene and copolymers, gelled electrolytes etc. It also reviews the various chemical approaches including modifying PEO to synthesizing complicated polymer architecture. In addition, it discusses the effect of various lithium salts on the conductivity of PEO-based polymers. Charge/discharge and cycle life data of polymer cells containing oxide and chalcogenide cathodes and lithium (Li) anode will be reviewed. Finally, future research directions to improve the electrolyte properties will be presented.
Conference Proceedings - Lasers and Electro-Optics Society Annual Meeting-LEOS
Lear, K.L.
Structure based on aluminum-oxide layers have led to dramatic improvements in VCSELs such as power conversion efficiencies in excess of 50% and threshold currents below 10μA. The low index, insulating aluminum-oxide, formed by selective wet thermal oxidation of AlGaAs, serves as an effective index guide as well as a current injection aperture. This paper presents data on devices with either two aligned apertures above and below the active region or with a single effective aperture above the active region leading to slope efficiencies of up to 1W/A.
Proceedings of SPIE - The International Society for Optical Engineering
Eaton, W.P.; Smith, J.H.
A surface micromachined pressure sensor array has been designed and fabricated. The sensors are based upon deformable, silicon nitride diaphragms with polysilicon piezoresistors. Absolute pressure is detected by virtue of reference pressure cavities underneath the diaphragms. For this type of sensor, design tradeoffs must be made among allowable diaphragm deflection, diaphragm size, and desirable pressure ranges. Several fabrication issues were observed and addressed. Offset voltage, sensitivity, and nonlinearity of 100 μm diameter sensors were measured.
The effect of solvent addition on the phase separation, mechanical properties and thermal stability of silica/siloxane composite materials prepared by in situ reinforcement was examined. The addition of a solvent enhances the miscibility of the reinforcement precursor, a partial hydrolyzate of tetraethoxysilane (TEOS-PH), with the polydimethylsiloxane (PDMS) polymer. As a result, the phase separation at the micron level, termed the large-scale structure, diminished in size. This decrease in particle size resulting from the addition of moderate amounts of solvent was accompanied by an improvement in the mechanical properties. However, solvent addition in the excess of 50 weight percent led to a decrease in mechanical properties even though the large-scale structure continued to diminish in size. Small Angle X-Ray Scattering (SAXS) was used to examine the angstrom level or small-scale structure. This small-scale structure was only affected by the presence of solvent, not the amount. The silica/siloxane composite materials showed the same thermal transition temperatures as the original PDMS material.
Lithium ion rechargeable batteries are predicted to replace Ni/Cd as the workhorse consumer battery. The pace of development of this battery system is determined in large part by the availability of materials and the understanding of interfacial reactions between materials. Lithium ion technology is based on the use of two lithium intercalating electrodes. Carbon is the most commonly used anode material, while the cathode materials of choice have been layered lithium metal chalcogenides (LiMX2) and lithium spinel-type compounds. Electrolytes may be either organic liquids or polymers. Although the first practical use of graphite intercalation compounds as battery anodes was reported in 1981 for molten salt cells and in 1983 for ambient temperature systems, it was not until Sony Energytech announced a new lithium ion intercalating carbon anode in 1990, that interest peaked. The reason for this heightened interest is that these electrochemical cells have the high energy density, high voltage and light weight of metallic lithium, but without the disadvantages of dendrite formation on charge, improving their safety and cycle life. This publication will review recent developments in the field and materials needs that will enhance future prospects for this important electrochemical system.
The preparation of light emitting diodes employing a new class of materials, 5,10-dihetera-5,10-dihydro-indeno[3,2b]indenes, as hole transport agents is described. These materials have been found to be more resistant to degradation by singlet oxygen than a poly(p-phenylene vinylene) (PPV) derivative.
Extensions of the German LIGA process have brought about fabrication capability suitable for cost effective production of precision engineered components. The process attributes allow fabrication of mechanical components which are not capable of being made via conventional subtractive machining methods. Two process improvements have been responsible for this extended capability which involve the areas of thick photoresist application and planarization via precision lapping. Application of low-stress x-ray photoresist has been achieved using room temperature solvent bonding of a preformed photoresist sheet. Precision diamond lapping and polishing has provided a flexible process for the planarization of a wide variety of electroplated metals in the presence of photoresist. Exposure results from the 2.5 GeV National Synchrotron Light Source storage ring at Brookhaven National Laboratory have shown that structural heights of several millimeter and above are possible. The process capabilities are also well suited for microactuator fabrication. Linear and rotational magnetic microactuators have been constructed which use coil winding technology with LIGA fabricated coil forms. Actuator output forces of 1 milliNewton have been obtained with power dissipation on the order of milliWatts. A rotational microdynamometer system which is capable of measuring torque-speed data is also discussed.
Plasma processes for etching and desmear of electronic components and printed wiring boards (PWB) are difficult to predict and control. Non-uniformity of most plasma processes and sensitivity to environmental changes make it difficult to maintain process stability from day to day. To assure plasma process performance, weight loss coupons or post-plasma destructive testing must be used. The problem with these techniques is that they are not real-time methods and do not allow for immediate diagnosis and process correction. These tests often require scrapping some fraction of a batch to insure the integrity of the rest. Since these tests verify a successful cycle with post-plasma diagnostics, poor test results often determine that a batch is substandard and the resulting parts unusable. These tests are a costly part of the overall fabrication cost. A more efficient method of testing would allow for constant monitoring of plasma conditions and process control. Process anomalies should be detected and corrected before the parts being treated are damaged. Real time monitoring would allow for instantaneous corrections. Multiple site monitoring would allow for process mapping within one system or simultaneous monitoring of multiple systems. Optical emission spectroscopy conducted external to the plasma apparatus would allow for this sort of multifunctional analysis without perturbing the glow discharge. In this paper, optical emission spectroscopy for non-intrusive, in situ process control will be explored along with applications of this technique towards process control, failure analysis and endpoint determination.
To verify the excitonic nature of the light-emitting state in PPV, fluorescence intensities and decay lifetimes were investigated as a function of excitation intensity. The results agree with the behavior predicted by the molecular exciton model. In particular, exciton-exciton annihilation causes the fluorescence intensity to saturate and the fluorescence lifetime to shorten at high exciton densities. In addition, the exciton annihilation, and thus diffusion, coefficients are found to be relatively large, even at low temperatures, indicating that exciton migration is important in PPV. These results indicate that the fluorescent (photoluminescent) state in PPV is excitonic in nature. The results argue against the band model where high mobility at reduced temperatures is not expected because the light-emitting species, neutral bipolarons, are associated with large lattice distortions.
Diametral compression strength distributions and the compaction behavior and of irregular shape 150-200 μm ceramic granules and uniform-size 210 μm glass spheres were measured to determine how granule strength variability relates to compaction behavior of granular assemblies. High variability in strength, represented by low Weibull modulus values (m<3) was observed for ceramic granules having a distribution of sizes and shapes, and for uniform-size glass spheres. Compaction pressure data were also analyzed using a Weibull distribution function, and the results were very similar to those obtained from the diametral compression strength tests for the same material. This similarity suggests that it may be possible to model granule compaction using a weakest link theory, whereby an assemblage of granules is viewed as the links of a chain, and failure of the weakest granule (i.e., the weakest link) leads to rearrangement and compaction. Additionally, with the use of Weibull statistics, it appears to be possible to infer the variability in strength of individual granules from a simple pressure compaction test, circumventing the tedious task of testing individual granules.
In ceramic manufacturing processes such as dry-pressing, correlations between applied compacting pressure and resultant powder compact density are essential for defining reliable process conditions for ceramic components. Pressure-density diagrams have been developed as a tool for both process control and for understanding the compaction behavior of different powders. These types of diagrams, however, pertain only to the average properties of a powder compact and do not address a significant issue in powder compaction processes: the formation of density gradients within the compact. Continuum-based mechanics models of varying complexity have addressed the influence of frictional forces acting at the powder-die wall interface which dissipate the applied pressure throughout the compact. Resulting pressure distribution models are then typically coupled with empirical functions relating pressure and density to obtain a green density distribution in the compact. All of these models predict similar trends; however, none predict the distribution with sufficient accuracy to be considered as a design tool for industrial applications.
Because the components of a multiphase flow often exhibit different electrical properties, a variety of probes have been developed to study such flows by measuring impedance in the region of interest. Researchers are now using electric fields to reconstruct the impedance distribution within a measurement volume via Electrical Impedance Tomography (EIT). EIT systems employ voltage and current measurements on the boundary of a domain to create a representation of the impedance distribution within the domain. The development of the Sandia EIT system (S-EIT) is reviewed. The construction of the projection acquisition system is discussed and two specific EIT inversion algorithms are detailed. The first reconstruction algorithm employs boundary element methods, and the second utilizes finite elements. The benefits and limitations of EIT systems are also discussed. Preliminary results are provided.
A flexible, modular manufacturing process for integrating micromechanical and microelectronic devices has been developed. This process embeds the micromechanical devices in an anisotropically etched trench below the surface of the wafer. Prior to microelectronic device fabrication, this trench is refilled with oxide, chemical-mechanically polished, and sealed with a nitride cap in order to embed the micromechanical devices below the surface of the planarized wafer. The feasibility of this technique in a manufacturing environment has been demonstrated by combining a variety of embedded micromechanical structures with a 2 μm CMOS process on 6 inch wafers. A yield of 78% has been achieved on the first devices manufactured using this technique.
New characterization and computational techniques have been developed to evaluate and simulate binder burnout from pressed powder compacts. Using engineering data and a control volume finite element method (CVFEM) thermal model, a nominally one dimensional (1-D) furnace has been designed to test, refine, and validate computer models that stimulate binder burnout assuming a 1-D thermal gradient across the ceramic body during heating. Experimentally, 1-D radial heat flow was achieved using a rod-shaped heater that directly heats the inside surface of a stack of ceramic annuli surrounded by thermal insulation. The computational modeling effort focused on producing a macroscopic model for binder burnout based on continuum approaches to heat and mass conservation for porous media. Two increasingly complex models have been developed that predict the temperature and mass of a porous powder compact as a function of time during binder burnout. The more complex model also predicts the pressure within a powder compact during binder burnout. Model predictions are in reasonably good agreement with experimental data on binder burnout from a 57-65% relative density pressed powder compact of a 94 wt% alumina body containing approx. 3 wt% binder. In conjunction with the detailed experimental data from the prototype binder burnout furnace, the models have also proven useful for conducting parametric studies to elucidate critical material property data required to support model development.
The pressure-compaction response of a spray-dried, 94% alumina powder containing several percent of a polymeric binder was investigated as a function of die diameter and compact aspect ratio. The results show that the die fill density decreases markedly with decreasing die diameter and aspect ratio, while the final green density (at 120 MPa) decreases only slightly under the same conditions. These results suggest that the ratio of the initial compact dimensions to the size of the granules may be much more important than previously considered.
This paper describes an algorithm for determining the optimal placement of a robotic manipulator within a workcell for minimum time coordinated motion. The algorithm uses a simple principle of coordinated motion to estimate the time of a joint interpolated motion. Specifically, the coordinated motion profile is limited by the slowest axis. Two and six degrees of freedom examples are presented. In experimental tests on a FANUC S-800 arm, the optimal placement of the robot can improve the cycle time of a robotic operation by as much as 25%. In high volume processes where the robot motion is currently the limiting factor, this increased throughput can result in substantial cost savings.
The emergence of several rapid prototyping & manufacturing (RP&M) technologies is having a dramatic impact on investment casting. While the most successful of the rapid prototyping technologies are almost a decade old, relatively recent process advances in their application have produced some remarkable success in utilizing their products as patterns for investment castings. Sandia National Laboratories has been developing highly coupled experimental and computational capabilities to examine the investment casting process with the intention of reducing the amount of time required to manufacture castings, and to increase the quality of the finished product. This presentation will begin with process aspects of RP&M pattern production and handling, shell fabrication, burnout, and casting. The emphasis will be on how the use of Stereolithography (SL) or Selective Laser Sintered (SLS) patterns differs from more traditional wax pattern processes. Aspects of computational simulation to couple design, thermal analysis, and mold filling will be discussed. Integration of these topics is probably the greatest challenge to the use of concurrent engineering principles with investment casting. Sandi has conducted several experiments aimed at calibrating computer codes and providing data for input into these simulations. Studied involving materials as diverse as stainless steel and gold have been conducted to determine liquid metal behavior in molds via real time radiography. The application of these experiments to predictive simulations will be described.
Nanosecond Pulsed Power provides the unique capability to deliver high energy and high power at low cost and high efficiency. One important application of this technology is to the generation of intense, high-energy laboratory X-ray sources using magnetically driven implosions. Saturn generates approx.500 kilojoules of x-rays using this process. This paper presents a detailed design concept for a approx.15 MJ laboratory X-ray source and discusses the resultant capabilities for high energy density physics studies.
A novel technique has been used to test the relative low cycle thermal fatigue resistance of different grades of US and Russian beryllium, which is proposed as plasma facing armor for fusion reactor first wall, limiter, and divertor components. A 30 kW electron beam test system was used to sweep the beam spot along one direction at 1 Hz. An in-vacuo fiber optic borescope was used to visually inspect the beryllium surfaces for crack initiation. Good agreement was found between the measured depth of cracks and a 2-D elastic-plastic finite element stress analysis.
The purpose of hazardous and radioactive materials packaging is to enable these materials to be transported without posing a threat to the health or property of the general public. To achieve this aim, regulations in the United States have been written establishing general design requirements for such packagings. While no regulations have been written specifically for mixed waste packaging, regulations for the constituents of mixed wastes, i.e., hazardous and radioactive substances, have been codified by the US Department of Transportation (DOT, 49 CFR 173) and the US Nuclear Regulatory Commission (NRC, 10 CFR 71). The design requirements for both hazardous [49 CFR 173.24 (e)(1)] and radioactive [49 CFR 173.412 (g)] materials packaging specify packaging compatibility, i.e., that the materials of the packaging @d any contents be chemically compatible with each other. Furthermore, Type A [49 CFR 173.412 (g)] and Type B (10 CFR 71.43) packaging design requirements stipulate that there be no significant chemical, galvanic, or other reaction between the materials and contents of the package. Based on these requirements, a Chemical Compatibility Testing Program was developed in the Transportation Systems Department at Sandia National Laboratories (SNL). The program attempts to assure any regulatory body that the issue of packaging material compatibility towards hazardous and radioactive materials has been addressed. This program has been described in considerable detail in an internal SNL document, the Chemical Compatibility Test Plan & Procedure Report (Nigrey 1993).
Sulfuric acid hydrogen peroxide mixtures (SPM) are commonly used in the semiconductor industry to remove organic contaminants from wafer surfaces. This viscous solution is very difficult to rinse off water surfaces. Various rinsing conditions were tested and the resulting residual acid left on the water surface was measured. Particle growth resulting from incomplete rinse is correlated with the amount of sulfur on the wafer surface measured by Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS). The amount of sulfur on the wafer structure after the rinse step is strongly affected by the wafer film type and contact angle prior to the SPM clean.
Intercalation anodes of graphite or disordered carbon in rechargeable Li-ion batteries (based on aprotic organic solvents) develop a passivating film during the first intercalation of Li{sup +}. The formation of this film reduces the cycling efficiency and results in excessive consumption of Li{sup +}. The exact nature of this film is not well defined, although there are many similarities in properties to the films that form on Li anodes under similar cycling conditions. In this study we report on characterization studies of films formed during galvanostatic cycling of disordered carbons derived from polymethylacryolintrile (PMAN) in a 1M LiPF{sub 6} solution in ethylene carbonateldimethyl carbonate solution (1:1 by vol.). Complementary tests were also conducted with glass carbon, where intercalation cannot occur. Complex-impedance spectroscopy was the primary measurement technique, supplemented by cyclic voltammetry.
This paper demonstrates a methodology for predicting the service lifetime of wind turbine blades using the high-cycle fatigue data base for typical U.S. blade materials developed by Mandell, et al. (1995). The first step in the analysis is to normalize the data base (composed primarily of data obtained from specialized, relatively small coupons) with fatigue data from typical industrial laminates to obtain a Goodman Diagram that is suitable for analyzing wind turbine blades. The LIFE2 fatigue analysis code for wind turbines is then used for the fatigue analysis of a typical turbine blade with a known load spectrum. In the analysis, a linear damage model, Miner`s Rule, is used to demonstrate the prediction of the service lifetime for a typical wind turbine blade under assumed operating strain ranges and stress concentration factors. In contrast to typical European data, the asymmetry in this data base predicts failures under typical loads to be compressive.
We have investigated whether an in-situ hydrogen or ammonia rf-plasma treatment prior to a PECVD-nitride deposition would promote bulk defect passivation independently of surface effects. We also studied whether the predeposition of a thin silicon-nitride protective layer vbefore performing the plasma treatment would serve to minimize surface damage. We found that for the limited set of deposition conditions in of cells processed using the used five different deposition strategies and compared the resulting cell performance with that investigated so far, the direct deposition of PECVD-nitride produces the best cells on String Ribbon silicon wafers to date, with efficiencies up to 14.5%. Hydrogen and ammonia plasma pretreatments without a protective nitride layer resulted in better bulk passivation, but damaged surfaces. Pretreatments after deposition of the protective layer produced the best surface passivation, but were not effective in passivating the bulk.
Researchers at Plasma Processes Inc. have produced a Functional Gradient Material (FGM) through advanced vacuum plasma spray processing for high heat flux applications. Outlined in this paper are the manufacturing methods used to develop a four component functional gradient material of copper, tungsten, boron, and boron nitride. The FGM was formed with continuous gradients and integral cooling channels eliminating bondlines and providing direct heat transfer from the high temperature exposed surface to a cooling medium. Metallurgical and x-ray diffraction analyses of the materials formed through innovative VPS (vacuum plasma spray) processing are also presented. Applications for this functional gradient structural material range from fusion reactor plasma facing components to missile nose cones to boilers.
This paper investigates the use of artificial neural networks (ANNs) to identify damage in mechanical systems. Two probabilistic neural networks (PNNs) are developed and used to judge whether or not damage has occurred in a specific mechanical system, based on experimental measurements. The first PNN is a classical type that casts Bayesian decision analysis into an ANN framework, it uses exemplars measured from the undamaged and damaged system to establish whether system response measurements of unknown origin come from the former class (undamaged) or the latter class (damaged). The second PNN establishes the character of the undamaged system in terms of a kernel density estimator of measures of system response; when presented with system response measures of unknown origin, it makes a probabilistic judgment whether or not the data come from the undamaged population. The physical system used to carry out the experiments is an aerospace system component, and the environment used to excite the system is a stationary random vibration. The results of damage identification experiments are presented along with conclusions rating the effectiveness of the approaches.
We present a software environment integrating analysis and test based models to support optimal modal test design through a Virtual Environment for Test Optimization (VETO). The VETO assists analysis and test engineers in maximizing the value of each modal test. It is particularly advantageous for structural dynamics model reconciliation applications. The VETO enables an engineer to interact with a finite element model of a test object to optimally place sensors and exciters and to investigate the selection of-data acquisition parameters needed to conduct a complete modal survey. Additionally, the user can evaluate the use of different types of instrumentation such as filters, amplifiers and transducers for which models are available in the VETO. The dynamic response of most of the virtual instruments (including the device under test) are modeled in the state space domain. Design of modal excitation levels and appropriate test instrumentation are facilitated by the VETO`s ability to simulate such features as unmeasured external inputs, A/D quantization effects, and electronic noise. Measures of the quality of the experimental design, including the Modal Assurance Criterion, and the Normal Mode indicator Function are available. The VETO also integrates tools such as Effective Independence and minamac to assist in selection of optimal sensor locations. The software is designed about three distinct modules: (1) a main controller and GUI written in C++, (2) a visualization model, taken from FEAVR, running under AVS, and (3) a state space model and time integration module, built in SIMULINK. These modules are designed to run as separate processes on interconnected machines. MATLAB`s external interface library is used to provide transparent, bidirectional communication between the controlling program and the computational engine where all the time integration is performed.
The experimental data on sorption and solubility of hydrogen isotopes in graphite in a wide ranges of temperature and pressure are reviewed. The Langmuir type adsorption is proposed for the hydrogen -- graphites interaction with taking into account dangling sp{sup 2}{minus}bonds relaxation. Three kinds of traps are proposed: Carbon interstitial loops with the adsorption enthalpy of {minus}4.4 eV/H{sub 2} (Traps l); carbon network edge atoms with the adsorption enthalpy of {minus}2.3 eV/H{sub 2} (Traps 2): Basal planes adsorption sites with enthalpy of +2.43 eV/H{sub 2} (Traps 3). The sorption capacity of every kind of graphite could be described with its own unique set of traps. The number of potential sites for the ``true solubility`` (Traps 3) we assume as 1E+6 appm, or HC=l, but endothermic character of this solubility leads to negligible amount of inventory in comparison with Traps 1 and Traps 2. The irradiation with neutrons or carbon atoms increases the number of Traps 1 and Traps 2. At damage level of {approximately}1 dpa under room temperature irradiation the number of these traps was increased up to 1500 and 5000 appm respectively. Traps 1 and Traps 2 are stable under high temperature annealing.
Last year the USNRC initiated a program at Sandia National Laboratories to determine the potential impact of smoke on advanced safety-related digitial instrumentation. In recognition of the fact that the reliability of safety-related equipment during or shortly after a fire in a nuclear power plant is more risk significant than long-term effects, we are concentrating on short-term failures. We exposed a multiplexer module board to three different types of smoke to determine whether the smoke would affect its operation. The operation of the multiplexer board was halted by one out of the three smoke exposures. In coordination with Oak Ridge National Laboratory, an experimental digital safety system was also smoke tested. The series of tests showed that smoke can cause potentially serious failures of a safety system. Most of these failures were intermittent and showed that smoke can temporarily interrupt communication between digital systems.
Direct observations of atomic motion with the field ion microscope (FIM) are providing detailed information on the mechanisms and energetics by which small clusters migrate across metal surfaces. An important result to emerge from these studies is that the activation energies of surface diffusion for small clusters on fcc(100) surfaces are strongly correlated with their shape. For Rh clusters on Rh(100) this correlation leads to an oscillatory behavior in the cluster mobility as a function of cluster size. For Pt on Rh(100) the activation energy is constant as clusters increase in size from three to five atoms and is also correlated with shape. The atomic-level mechanism involved in cluster diffusion on fcc(100) surfaces is inferred from a comparison of the measured activation energies to previous theoretical calculations.
This paper describes the use of backscattered electron Kikuchi patterns (BEKP) for phase identification in the scanning electron microscope (SEM). The origin of BEKP is described followed by a discussion of detectors capable of recording high quality patterns. In this study a new detector based on charge coupled device technology is described. Identification of unknown phases is demonstrated on prepared and as received sample surfaces. Identification through a combination of energy dispersive x-ray spectrometry (EDS) and BEKP of a Laves phase in a weld in an alloy of Fe-Co-Ni-Cr-Nb and the identification of Pb{sub 2}Ru{sub 2}O{sub 6.5} crystals on PZT is demonstrated. Crystallographic phase analysis of micron sized phases in the SEM is a powerful new tool for materials characterization.
The Trajectory Analysis and Optimization System (TAOS) is software that simulates point--mass trajectories for multiple vehicles. It expands upon the capabilities of the Trajectory Simulation and Analysis program (TAP) developed previously at Sandia National Laboratories. TAOS is designed to be a comprehensive analysis tool capable of analyzing nearly any type of three degree-of-freedom, point-mass trajectory. Trajectories are broken into segments, and within each segment, guidance rules provided by the user control how the trajectory is computed. Parametric optimization provides a powerful method for satisfying mission-planning constraints. Althrough TAOS is not interactive, its input and output files have been designed for ease of use. When compared to TAP, the capability to analyze trajectories for more than one vehicle is the primary enhancement, although numerous other small improvements have been made. This report documents the methods used in TAOS as well as the input and output file formats.
Sandia is modifying the PBFA II accelerator into a dual use facility. While maintaining the present ion-beam capability, we are developing a long-pulse, high-current operating mode for magnetically-driven implosions. This option, called PBFA II-Z, will require new water transmission lines, a new insulator stack, and new magnetically-insulated transmission lines (MITLs). Each of the existing 36, coaxial water pulse-forming sections will couple to a 4.5-{Omega}, bi-plate water-transmission line. The water transmission lines then feed a four-level insulator stack. The insulators are expected to operate at a maximum, spatially-averaged electric field of {approximately}l00 kV/cm. The MITL design is based on the successful biconic Saturn design. The four ``disk`` feeds will each have a vacuum impedance of {approximately}2.0 {Omega}. The disk feeds are added in parallel using a double post-hole convolute at a diameter of 15 cm. We predict that the accelerator will deliver 20 MA to a 15-mg z-pinch load in 100 ns, making PBFA II-Z the most powerful z-pinch driver in the world providing a pulsed power and load physics scaling testbed for future 40-80-MA drivers.
A rationale was developed to determine which technologies a space nuclear reactor technology based program pursue based on the fact that budgets would be limited. A preliminary evaluation was conducted to identify key technical issues and to recommend a prioritized set of candidate research projects that could be undertaken as part of the Defense Nuclear Agency (DNA) program in the near term. The recommendations made have not been adopted formally by the DNA`s Topaz International Program process. (TIP), but serve as inputs to the program plannin process.
A set of ``templates`` was developed for modeling waste glass interactions with cement-based and clay-based matrices. The templates consist of a modified thermodynamic database, and input files for the EQ3/6 reaction path code, containing embedded rate models and compositions for waste glass, cement, and several pozzolanic materials. Significant modifications were made in the thermodynamic data for Th, Pb, Ra, Ba, cement phases, and aqueous silica species. It was found that the cement-containing matrices could increase glass corrosion rates by several orders of magnitude (over matrixless or clay matrix systems), but they also offered the lowest overall solubility for Pb, Ra, Th and U. Addition of pozzolans to cement decreased calculated glass corrosion rates by up to a factor of 30. It is shown that with current modeling capabilities, the ``affinity effect`` cannot be trusted to passivate glass if nuclei are available for precipitation of secondary phases that reduce silica activity.
A series of CO{sub 2} laser welds were made at a constant beam irradiance of 6 MW/cm{sup 2} on 304 stainless steel with travel speeds selected to produce welds with varying levels of weld penetration. Using a Seebeck envelope calorimeter, the net heat input to the part was measured for each weld. It was found that the energy transfer efficiencies varied from 0.29 to 0.86, and decreased at high travel speeds where the weld penetration depth was as shallow as 0.13 mm. The decrease in beam absorption with decreasing weld pool depth is consistent with an absorption mechanism that requires multiple internal reflections within the weld pool. Equations have been developed which conn -ct the keyhole cavity dimensions with the energy transfer efficiency, and correlations with the experimental data have determined the keyhole cavity radius to be 0.1 mm for a focused laser beam with a spot radius of 0.059 mm.
Costs associated with designing and fabricating fixtures may be a significant portion of the total costs associated with a manufacturing task. The software tool, HoldFast, designs optimal fixtures that hold a single workpiece, are easily fabricated, provide rigid constraint and deterministic location of the workpiece, are robust to workpiece shape variations, obey all associated task constraints, and are easy to load and unload. We illustrate the capabilities of HoldFast by designing fixtures for several examples. Fixtures are designed and built for finish-machining and drilling of a cast part for prototype fabrication and mass-production fabrication. A pallet fixture is designed for vertical assembly of a personal cassette player. Another pallet fixture is designed and built that will hold either the personal cassette player or a glue gun during assembly.
A number of physics problems can be modeled by a set of N elements which have pair-wise interactions with one another. A direct solution technique requires computational effort which is O(N{sup 2}). Fast multipole methods (FMM) have been widely used in recent years to obtain solutions to these problems requiring a computational effort of only 0 (N lnN) or O (N). In this paper we present an overview of several variations of the fast multipole method along with examples of its use in solving a variety of physical problems.
The crystalline silico-titanates developed by the Department of Chemical Engineering at Texas A&M University, Sandia National Laboratories and UOP exhibits extremely high ion exchange selectivity for removing cesium from aqueous defense wastes. Based on experimental data and structure studies, a competitive ion exchange model was proposed to predict the ion exchange performance in different simulated waste solutions. The predicted distribution coefficients were within 10% of the experimentally determined values.
In late 1994, Sandia National Laboratories in Albuquerque, New Mexico, (SNL/NM), was instructed by the Department of Energy (DOE) Isotope Production and Distribution Program (IPDP) to examine the feasibility of producing medically useful radioisotopes using the Annular Core Research Reactor (ACRR) and the Hot Cell Facility (HCF). Los Alamos National Laboratory (LANL) would be expected to supply the targets to be irradiated in the ACRR. The intent of DOE would be to provide a capability to satisfy the North American health care system demand for {sup 99}Mo, the parent of {sup 99m}Tc, in the event of an interruption in the current Canadian supply. {sup 99m}Tc is used in 70 to 80% of all nuclear medicine procedures in the US. The goal of the SNL/NM study effort is to determine the physical plant capability, infrastructure, and staffing necessary to meet the North American need for {sup 99}Mo and to identify and examine all issues with potential for environmental impact.
This report presents a two-year LDRD research effort into multisensor data fusion. We approached the problem by addressing the available types of data, preprocessing that data, and developing fusion algorithms using that data. The report reflects these three distinct areas. First, the possible data sets for fusion are identified. Second, automated registration techniques for imagery data are analyzed. Third, two fusion techniques are presented. The first fusion algorithm is based on the two-dimensional discrete wavelet transform. Using test images, the wavelet algorithm is compared against intensity modulation and intensity-hue-saturation image fusion algorithms that are available in commercial software. The wavelet approach outperforms the other two fusion techniques by preserving spectral/spatial information more precisely. The wavelet fusion algorithm was also applied to Landsat Thematic Mapper and SPOT panchromatic imagery data. The second algorithm is based on a linear-regression technique. We analyzed the technique using the same Landsat and SPOT data.
This document describes the processes to be used for creating corporate information systems within the scope of the Integrated Information Services (IIS) Center. Issue B describes all phases of the life cycle, with strong emphasis on the interweaving of the Analysis and Design phases. This Issue B supersedes Issue A, which concentrated on the Analysis and Implementation phases within the context of the entire life cycle. Appendix A includes a full set of examples of the deliverables, excerpted from the Network Database. Subsequent issues will further develop these life cycle processes as we move toward enterprise-level management of information assets, including information meta-models and an integrated corporate information model. The phases described here, when combined with a specifications repository, will provide the basis for future reusable components and improve traceability of information system specifications to enterprise business rules.
The RADTRAN 4 computer code, which calculates estimates of accident dose-risk corresponding to specified transportation scenarios, ascribes doses to potentially exposed members of the public. These persons are modeled as not being evacuated from the affected area for 24 hours following a release of radioactive material. Anecdotal evidence has suggested that this value may be unnecessarily conservative; consequently risk estimates are unnecessarily high. An initial survey of recent trucking accidents, reported in newspapers and other periodicals (1988 through 1994), that involved evacuation of the general population in the affected areas was undertaken to establish the actual time required for such evacuations. Accidents involving hazardous materials other than those which are radioactive (e.g., gasoline, insecticides, other chemicals) but also requiring evacuations of nearby residents were included in the survey. However, the resultant set of sufficiently documented trucking incidents yielded rather sparse data [1]. When the probability density distribution of the truck accident data was compared with that resulting from addition of four other (rail and fixed site) incidents, there was no statistically significant difference between them. Therefore, in order to improve the statistical significance of the data set, i.e., maximize the number of pertinent samples, a search for evacuations resulting from all types of accidents was performed. This resulted in many more references; a set of 48 incidents which could be adequately verified was compiled and merged with the original two data sets for a total of 66 evacuation accounts.
This paper presents a nonlocal analysis of the dynamic damage accumulation processes in brittle solids. A nonlocal formulation of a microcrack based continuum damage model is developed and implemented into a transient dynamic finite element computer code. The code is then applied to the study of the damage accumulation process in a concrete plate with a central hole and subjected to the action of a step tensile pulse applied at opposite edges of the plate. Several finite element discretizations are used to examine the mesh size effect. Comparisons between calculated results based on local and nonlocal formulations are made and nonlocal effects are discussed.
Cables have been identified as critical components requiring detailed technical evaluation for extending the lifetime of Light Water Reactors beyond 40 years. This paper highlights some of the DOE-sponsored cable aging studies currently underway at Sandia. These studies are focused on two important issues: the validity of the often-used Arrhenius thermal aging prediction method and methods for predicting lifetimes in combined thermal-radiation environments. Accelerated thermal aging results are presented for three cable jacket and insulation materials, which indicate that hardening of the outside surface has an Arrhenius temperature dependence and correlates well with reductions in ultimate tensile elongation. This suggests that the indentor approach is a promising NDE technique for cable jacket and unjacketed insulation materials installed in thermally-dominated regions of nuclear power plants.
The 1994 Fernald field characterization demonstration program, hosted by Fernald Environmental Management Project, was established to investigate technologies that are applicable to the characterization and remediation of soils contaminated with uranium. An important part of this effort was evaluating field-screening tools potentially capable of acquiring high-resolution information on uranium contamination distribution in surface soils. Further-more, the information needed to be obtained in a cost- and time-efficient manner. Seven advanced field-screening technologies were demonstrated at a uranium-contaminated site at Fernald, located 29 kilometers northwest of Cincinnati, Ohio. The seven technologies tested were: (1) alpha-track detectors, (2) a high-energy beta scintillometer, (3) electret ionization chambers, (4) and (5) two variants of gamma-ray spectrometry, (6) laser ablation-inductively coupled plasma-atomic emission spectroscopy, and (7) long-range alpha detection. The goals of this field demonstration were to evaluate the capabilities of the detectors and to demonstrate their utility within the US Department of Energy`s Environmental Restoration Program. Identical field studies were conducted using four industry-standard characterization tools: (1) a sodium-iodide scintillometer, (2) a low-energy FIDLER scintillometer, (3) a field-portable x-ray fluorescence detector, and (4) standard soil sampling coupled with laboratory analysis. Another important aspect of this program was the application of a cost/risk decision model to guide characterization of the site. This document is a compilation of raw data submitted by the technologies and converted total uranium data from the 1994 Fernald field characterization demonstration.
Prosperity Games are an outgrowth and adaptation of move/countermove and seminar War Games. Prosperity Games are simulations that explore complex issues in a variety of areas including economics, politics, sociology, environment, education and research. These issues can be examined from a variety of perspectives ranging from a global, macroeconomic and geopolitical viewpoint down to the details of customer/supplier/market interactions in specific industries. All Prosperity Games are unique in that both the game format and the player contributions vary from game to game. This report documents the Environmental Prosperity Game conducted under the sponsorship of the Silicon Valley Environmental Partnership. Players were drawn from all stakeholders involved in environmental technologies including small and large companies, government, national laboratories, universities, environmentalists, the legal profession, finance, and the media. The primary objectives of this game were to: investigate strategies for developing a multi-agency (national/state/regional), one-step regulatory approval process for certifying and implementing environmental technologies and evaluating the simulated results; identify the regulatory hurdles and requirements, and the best approaches for surmounting them; identify technical problems and potential resources (environmental consultants, labs, universities) for solving them. The deliberations and recommendations of these players provided valuable insights as to the views of this diverse group of decision makers concerning environmental issues, including the development, licensing, and commercialization of new technologies.
The LRSTF report for Phase I of its evaluation of low-residue soldering was issued in June 1995. This Appendix summarizes the results of follow-on testing performed in Phase II and compares electrical test results for both phases. Deliberate decisions were made by the LRSTF in Phase I to challenge the design guideline limits in MILSTD-275, Printed Wiring for Electronic Equipment The LRSTF considered this approach to produce a ``worst case`` design and provide useful information about the robustness of LR soldering processes. As such, good design practices were sometimes deliberately violated in designing the LRSTF board. This approach created some anomalies for both LR boards and RMA/cleaned controls. Phase II testing verified that problems that affected both RMA/cleaned and LR boards in Phase I were design related.
This report summarizes the technical progress made in the past three years on CRADA No. 1078, Molecular Engineering of Polymer Alloys. The thrust of this CRADA was to start with the basic ideas of PRISM theory and develop it to the point where it could be applied to modeling of polymer alloys. In this program, BIOSYM, Sandia and the University of Illinois worked jointly to develop the theoretical techniques and numerical formalisms necessary to implement the theoretical ideas into commercial software aimed at molecular engineering of polymer alloys. This CRADA focused on developing the techniques required to make the transition from theory to practice. These techniques were then used by BIOSYM to incorporate PRISM theory and other new developments into their commercial software.
Constitutive models describing the deformation of crushed salt are presented in this report. Ten constitutive models with potential to describe the phenomenological and micromechanical processes for crushed salt were selected from a literature search. Three of these ten constitutive models, termed Sjaardema-Krieg, Zeuch, and Spiers models, were adopted as candidate constitutive models. The candidate constitutive models were generalized in a consistent manner to three-dimensional states of stress and modified to include the effects of temperature, grain size, and moisture content. A database including hydrostatic consolidation and shear consolidation tests conducted on Waste Isolation Pilot Plant and southeastern New Mexico salt was used to determine material parameters for the candidate constitutive models. Nonlinear least-squares model fitting to data from the hydrostatic consolidation tests, the shear consolidation tests, and a combination of the shear and hydrostatic tests produces three sets of material parameter values for the candidate models. The change in material parameter values from test group to test group indicates the empirical nature of the models. To evaluate the predictive capability of the candidate models, each parameter value set was used to predict each of the tests in the database. Based on the fitting statistics and the ability of the models to predict the test data, the Spiers model appeared to perform slightly better than the other two candidate models. The work reported here is a first-of-its kind evaluation of constitutive models for reconsolidation of crushed salt. Questions remain to be answered. Deficiencies in models and databases are identified and recommendations for future work are made. 85 refs.
To properly characterize the transport of contaminants from the sediments beneath the Hanford Site into the Columbia River, a suite of In Situ Permeable Flow Sensors was deployed to accurately characterize the hydrologic regime in the banks of the river. The three dimensional flow velocity was recorded on an hourly basis from mid May to mid July, 1994 and for one week in September. The first data collection interval coincided with the seasonal high water level in the river while the second interval reflected conditions during relatively low seasonal river stage. Two flow sensors located approximately 50 feet from the river recorded flow directions which correlated very well with river stage, both on seasonal and diurnal time scales. During time intervals characterized by falling river stage, the flow sensors recorded flow toward the river while flow away from the river was recorded during times of rising river stage. The flow sensor near the river in the Hanford Formation recorded a component of flow oriented vertically downward, probably reflecting the details of the hydrostratigraphy in close proximity to the probe. The flow sensor near the river in the Ringold Formation recorded an upward component of flow which dominated the horizontal components most of the time. The upward flow in the Ringold probably reflects regional groundwater flow into the river. The magnitudes of the flow velocities recorded by the flow sensors were lower than expected, probably as a result of drilling induced disturbance of the hydraulic properties of the sediments around the probes. The probes were installed with resonant sonic drilling which may have compacted the sediments immediately surrounding the probes, thereby reducing the hydraulic conductivity adjacent to the probes and diverting the groundwater flow away from the sensors.
Cavity type receivers are used extensively in concentrating solar thermal energy collecting systems. The Solar Total Energy Project (STEP) in Shenandoah, Georgia is a large scale field test for the collection of solar thermal energy. The STEP experiment consists of a large field array of solar collectors used to supplement the process steam, cooling and other electrical power requirements of an adjacent knitwear manufacturing facility. The purpose of the tests, conducted for this study, was to isolate and quantify the radiative, conductive, and convective components of total heat loss, and to determine the effects of operating temperature, receiver angle, and aperture size on cavity heat loss. An analytical model for radiative heat loss was developed and compared with two other methods used to determine radiative heat loss. A proposed convective heat loss correlation, including effects of aperture size, receiver operating temperature, and receiver angle is presented. The resulting data is a source to evaluate the STEP measurements.
The light ion impurities C, 0 and H have been implanted or diffused into GaN and related compounds and their effect on the electrical properties of these materials measured by Hall, C-V and SIMS as a function of annealing temperatures from 300--11OO{degree}C. While C in as-grown GaN appears to create an acceptor under MOMBE conditions, implanted C shows no measurable activity. Similarly, implanted 0 does not show any shallow donor activity after annealing at {le}700{degree}C, but can create high resistivity regions (10{sup 6} {Omega}/{open_square}) in GaN, AlInN and InGaN for device isolation when annealed at 500--70O{degree}C. Finally, hydrogen is found to passivate shallow donor and acceptor states in GaN, InN. InAlN and InGaN, with dissociation of the neutral complexes at >450{degree}C. The liberated hydrogen does not leave the nitride films until much higher annealing temperatures (>800{degree}C). Typical reactivation energies are {approximately}2.0 eV for impurity-hydrogen complexes.
This document represents a summary of 58 technologies that are being developed by the Department of Energy`s (DOE`s) Office of Science and Technology (OST) to provide site, waste, and process characterization and monitoring solutions to the DOE weapons complex. The information was compiled to provide performance data on OST-developed technologies to scientists and engineers responsible for preparing Remedial Investigation/Feasibility Studies (RI/FSs) and preparing plans and compliance documents for DOE cleanup and waste management programs. The information may also be used to identify opportunities for partnering and commercialization with industry, DOE laboratories, other federal and state agencies, and the academic community. Each technology is featured in a format that provides: (1) a description, (2) technical performance data, (3) applicability, (4) development status, (5) regulatory considerations, (6) potential commercial applications, (7) intellectual property, and (8) points-of-contact. Technologies are categorized into the following areas: (1) Bioremediation Monitoring, (2) Decontamination and Decommissioning, (3) Field Analytical Laboratories, (4) Geophysical and Hydrologic Characterization, (5) Hazardous Inorganic Contaminant Analysis, (6) Hazardous Organic Contaminant Analysis, (7) Mixed Waste, (8) Radioactive Contaminant Analysis, (9) Remote Sensing,(10)Sampling and Drilling, (11) Statistically Guided Sampling, and (12) Tank Waste.
