AlGaN-channel high electron mobility transistors (HEMTs) are among a class of ultra wide-bandgap transistors that are promising candidates for RF and power applications. Long-channel AlxGa1-xN HEMTs with x = 0.7 in the channel have been built and evaluated across the -50°C to +200°C temperature range. These devices achieved room temperature drain current as high as 46 mA/mm and were absent of gate leakage until the gate diode forward bias turn-on at ~2.8 V, with a modest -2.2 V threshold voltage. A very large Ion/Ioff current ratio, of 8 × 109 was demonstrated. A near ideal subthreshold slope that is just 35% higher than the theoretical limit across the temperature range was characterized. The ohmic contact characteristics were rectifying from -50°C to +50°C and became nearly linear at temperatures above 100°C. An activation energy of 0.55 eV dictates the temperature dependence of off-state leakage.
Here, we present a low resistance, straightforward planar ohmic contact for Al0.45Ga0.55N/Al0.3Ga0.7N high electron mobility transistors. Five metal stacks (a/Al/b/Au; a = Ti, Zr, V, Nb/Ti; b = Ni, Mo, V) were evaluated at three individual annealing temperatures (850, 900, and 950°C). The Ti/Al/Ni/Au achieved the lowest specific contact resistance at a 900°C anneal temperature. Transmission electron microscopy analysis revealed a metal-semiconductor interface of Ti-Al-Au for an ohmic (900°C anneal) and a Schottky (850°C anneal) Ti/Al/Ni/Au stack. HEMTs were fabricated using the optimized recipe with resulting contacts that had room-temperature specific contact resistances of ρc = 2.5 × 10-5 Ω cm², sheet resistances of RSH = 3.9 kΩ/$\blacksquare$, and maximum current densities of 75 mA/mm (at VGATE of 2 V). Electrical measurements from -50 to 200°C had decreasing specific contact resistance and increasing sheet resistance, with increasing temperature. These contacts enabled state-of-the-art performance of Al0.45Ga0.55N/Al0.3Ga0.7N HEMTs.
A distributed impedance 'field cage' structure is proposed and evaluated for electric field control in GaN-based, lateral high electron mobility transistors operating as kilovolt-range power devices. In this structure, a resistive voltage divider is used to control the electric field throughout the active region. The structure complements earlier proposals utilizing floating field plates that did not employ resistively connected elements. Transient results, not previously reported for field plate schemes using either floating or resistively connected field plates, are presented for ramps of dVds/dt = 100 V/ns. For both dc and transient results, the voltage between the gate and drain is laterally distributed, ensuring that the electric field profile between the gate and drain remains below the critical breakdown field as the source-to-drain voltage is increased. Our scheme indicates promise for achieving the breakdown voltage scalability to a few kilovolts.
Emerging ultrawide bandgap semiconductor materials are logical candidates for applications that exploit the large critical electric field (EC) associated with these devices. For semiconductor devices, EC scales approximately as Eg2 5 [1]. With a 25% larger bandgap and an approximately 73% larger EC than GaN, Al0.3Ga0.7N-channel high election mobility transistors (HEMTs) might be viable candidates for harsh environment electronics or short wavelength photo-transistors. In either case, transistor quality factors such as minimal off-state leakage currents and subthreshold slope factor are important metrics.
Due to the ultra-wide bandgap of Al-rich AlGaN, up to 5.8 eV for the structures in this study, obtaining low resistance ohmic contacts is inherently difficult to achieve. A comparative study of three different fabrication schemes is presented for obtaining ohmic contacts to an Al-rich AlGaN channel. Schottky-like behavior was observed for several different planar metallization stacks (and anneal temperatures), in addition to a dry-etch recess metallization contact scheme on Al0.85Ga0.15N/Al0.66Ga0.34N. However, a dry etch recess followed by n+-GaN regrowth fabrication process is reported as a means to obtain lower contact resistivity ohmic contacts on a Al0.85Ga0.15N/Al0.66Ga0.34N heterostructure. Specific contact resistivity of 5 × 10−3 Ω cm2 was achieved after annealing Ti/Al/Ni/Au metallization.
Predicted lateral power device performance as a function of alloy composition is characterized by a standard lateral device figure-of-merit (LFOM) that depends on mobility, critical electric field, and sheet carrier density. The paper presents calculations of AlGaN electron mobility in lateral devices such as HEMTs across the entire alloy composition range. Alloy scattering and optical polar phonon scattering are the dominant mechanisms limiting carrier mobility. Due to the significant degradation of mobility from alloy scattering, at room temperature Al fractions greater than about 85% are required for improved LFOM relative to GaN using a conservative sheet charge density of 1 × 1013 cm−2. However, at higher temperatures at which AlGaN power devices are anticipated to operate, this “breakeven” composition decreases to about 65% at 500 K, for example. For high-frequency applications, the Johnson figure-of-merit (JFOM) is the relevant metric to compare potential device performance across materials platforms. At room temperature, the JFOM for AlGaN alloys is predicted to surpass that of GaN for Al fractions greater than about 40%.
AlGaN-channel high electron mobility transistors (HEMTs) are among a class of ultra wide-bandgap transistors that have a bandgap greater than ∼3.4 eV, beyond that of GaN and SiC, and are promising candidates for RF and power applications. Long-channel AlxGa1-xN HEMTs with x = 0.3 in the channel have been built and evaluated across the −50◦C to +200◦C temperature range. Room temperature drain current of 70 mA/mm, absent of gate leakage, and with a modest −1.3 V threshold voltage was measured. A very large Ion/Ioff current ratio, greater than 108 was demonstrated over the entire temperature range, indicating that off-state leakage is below the measurement limit even at 200◦C. Combined with near ideal subthreshold slope factor that is just 1.3× higher than the theoretical limit across the temperature range, the excellent leakage properties are an attractive characteristic for high temperature operation.
“Ultra” wide-bandgap semiconductors are an emerging class of materials with bandgaps greater than that of gallium nitride (EG > 3.4 eV) that may ultimately benefit a wide range of applications, including switching power conversion, pulsed power, RF electronics, UV optoelectronics, and quantum information. This paper describes the progress made to date at Sandia National Laboratories to develop one of these materials, aluminum gallium nitride, targeted toward high-power devices. The advantageous material properties of AlGaN are reviewed, questions concerning epitaxial growth and defect physics are covered, and the processing and performance of vertical- and lateral-geometry devices are described. The paper concludes with an assessment of the outlook for AlGaN, including outstanding research opportunities and a brief discussion of other potential applications.
Varying atomic ratios in compound semiconductors is well known to have large effects on the etching properties of the material. The use of thin device barrier layers, down to 25 nm, adds to the fabrication complexity by requiring precise control over etch rates and surface morphology. The effects of bias power and gas ratio of BCl3 to Cl2 for inductively coupled plasma etching of high Al content AlGaN were contrasted with AlN in this study for etch rate, selectivity, and surface morphology. Etch rates were greatly affected by both bias power and gas chemistry. Here we detail the effects of small variations in Al composition for AlGaN and show substantial changes in etch rate with regards to bias power as compared to AlN.
The performance and efficiency of power devices depends on both high breakdown voltage and low on-state resistance. For semiconductor devices, the critical electric field (EC) affecting breakdown scales approximately as Eg25 [1], making the wide bandgap semiconductor materials logical candidates for high voltage power electronics devices. In particular, AlGaN alloys approaching AlN with its 6.2 eV bandgap have an estimated EC approaching 5x that of GaN. This factor makes AlN/AlGaN high election mobility transistors (HEMTs) extremely interesting as candidate power electronic devices. Until now, such devices have been hampered, ostensibly due to the difficulty of making Ohmic contacts to AlGaN alloys with high Al composition. With the use of an AlN barrier etch and regrowth procedure for Ohmic contact formation, we are now able to report on an AlN/AlGaN HEMT with 85% Al.
An AlN barrier high electron mobility transistor (HEMT) based on the AlN/Al0.85Ga0.15N heterostructure was grown, fabricated, and electrically characterized, thereby extending the range of Al composition and bandgap for AlGaN channel HEMTs. An etch and regrowth procedure was implemented for source and drain contact formation. A breakdown voltage of 810 V was achieved without a gate insulator or field plate. Excellent gate leakage characteristics enabled a high Ion/Ioff current ratio greater than 107 and an excellent subthreshold slope of 75 mV/decade. A large Schottky barrier height of 1.74 eV contributed to these results. In conclusion, the room temperature voltage-dependent 3-terminal off-state drain current was adequately modeled with Frenkel-Poole emission.
Epitaxial (111) MgO films were prepared on (0001) AlxGa1-xN via molecular-beam epitaxy for x=0 to x=0.67. Valence band offsets of MgO to AlxGa1-xN were measured using X-ray photoelectron spectroscopy as 1.65±0.07eV, 1.36±0.05eV, and 1.05±0.09eV for x=0, 0.28, and 0.67, respectively. This yielded conduction band offsets of 2.75eV, 2.39eV, and 1.63eV for x=0, 0.28, and 0.67, respectively. All band offsets measured between MgO and AlxGa1-xN provide a>1eV barrier height to the semiconductor.
We investigate plasmonic structures in nitride-based materials for far-infrared (IR) applications. The two dimensional electron gas (2DEG) in the GaN/AlGaN material system, much like metal- dielectric structures, is a patternable plasmonic medium. However, it also permits for direct tunability via an applied voltage. While there have been proof-of-principle demonstrations of plasma excitations in nitride 2DEGs, exploration of the potential of this material system has thus far been limited. We recently demonstrated coherent phenomena such as the formation of plasmonic crystals, strong coupling of tunable crystal defects to a plasmonic crystal, and electromagnetically induced transparency in GaAs/AlGaAs 2DEGs at sub-THz frequencies. In this project, we explore whether these effects can be realized in nitride 2DEG materials above 1 THz and at temperatures exceeding 77 K.
