Publications

Abstract not provided.

In this study, the scaling of polarization and pyroelectric response across a thickness series (5–20 nm) of Hf_0.58Zr_0.42O₂ films with TaN electrodes was characterized. Reduction in thickness from 20 nm to 5 nm resulted in a decreased remanent polarization from 17 to 2.8 μC cm^-2. Accompanying the decreased remanent polarization was an increased absolute pyroelectric coefficient, from 30 to 58 μC m^-2 K^-1. The pyroelectric response of the 5 nm film was unstable and decreased logarithmically with time, while that of 10 nm and thicker films was stable over a time scale of >300 h at room temperature. Finally, the sign of the pyroelectric response was irreversible with differing polarity of poling bias for the 5 nm thick film, indicating that the enhanced pyroelectric response was of electret origins, whereas the pyroelectric response in thicker films was consistent with a crystallographic origin.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The different rate-limiting processes underlying ignition and self-propagating reactions in Al/Pt multilayers are examined through experiments and analytical modeling. Freestanding, ∼1.6 μm-thick Al/Pt multilayers of varied stoichiometries and nanometer-scale layer thicknesses ignite at temperatures below the melting point of both reactants (and eutectics) demonstrating that initiation occurs via solid-state mixing. Equimolar multilayers exhibit the lowest ignition temperatures when comparing structures having a specific bilayer thickness. An activation energy of 76.6 kJ/mol at. associated with solid state mass transport is determined from the model analysis of ignition. High speed videography shows that equimolar Al/Pt multilayers undergo the most rapid self-sustained reactions with wavefront speeds as large as 73 m/s. Al- and Pt-rich multilayers react at reduced rates (as low as 0.3 m/s), consistent with reduced heat of reaction and lower adiabatic temperatures. An analytical model that accounts for key thermodynamic properties, preliminary mixing along interfaces, thermal transport, and mass diffusion is used to predict the wavefront speed dependencies on bilayer thickness. Good fits to experimental data provide estimates for activation energy (51 kJ/mol at.) associated with mass transport subject to high heating rates and thermal diffusion coefficient of premixed interfacial volumes (2.8 × 10-6 m2/s). Pt dissolution into molten Al is identified as a rate-limiting step underlying high temperature propagating reactions in Al/Pt multilayers.

Abstract not provided.

Abstract not provided.

Cubic zirconium tungstate (α-ZrW2O8), a well-known negative thermal expansion material, has been investigated within the framework of density functional perturbation theory (DFPT), combined with experimental characterization to assess and validate computational results. Using combined Fourier transform infrared measurements and DFPT calculations, new and extensive assignments were made for the far-infrared (<400 cm−1) spectrum of α-ZrW2O8. A systematic comparison of DFPT-simulated infrared, Raman, and phonon density-of-state spectra with Fourier transform far-/mid-infrared and Raman data collected in this study, as well as with available inelastic neutron scattering measurements, shows the superior accuracy of the PBEsol exchange-correlation functional over standard PBE calculations for studying the spectroscopic properties of this material.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The powder-bed laser additive manufacturing (AM) process is widely used in the fabrication of three-dimensional metallic parts with intricate structures, where kinetically controlled diffusion and microstructure ripening can be hindered by fast melting and rapid solidification. Therefore, the microstructure and physical properties of parts made by this process will be significantly different from their counterparts produced by conventional methods. This work investigates the microstructure evolution for an AM fabricated AlSi10Mg part from its nonequilibrium state toward equilibrium state. Special attention is placed on silicon dissolution, precipitate formation, collapsing of a divorced eutectic cellular structure, and microstructure ripening in the thermal annealing process. These events alter the size, morphology, length scale, and distribution of the beta silicon phase in the primary aluminum, and changes associated with elastic properties and microhardness are reported. The relationship between residual stress and silicon dissolution due to changes in lattice spacing is also investigated and discussed.

Abstract not provided.

Processing of the low workability Fe-Co-1.5V (Hiperco® equivalent) alloy is demonstrated using the Laser Engineered Net Shaping (LENS) metals additive manufacturing technique. As an innovative and highly localized solidification process, LENS is shown to overcome workability issues that arise during conventional thermomechanical processing, enabling the production of bulk, near net-shape forms of the Fe-Co alloy. Bulk LENS structures appeared to be ductile with no significant macroscopic defects. Atomic ordering was evaluated and significantly reduced in as-built LENS specimens relative to an annealed condition, tailorable through selection of processing parameters. Fine equiaxed grain structures were observed in as-built specimens following solidification, which then evolved toward a highly heterogeneous bimodal grain structure after annealing. The microstructure evolution in Fe-Co is discussed in the context of classical solidification theory and selective grain boundary pinning processes. Magnetic properties were also assessed and shown to fall within the extremes of conventionally processed Hiperco® alloys. Hiperco® is a registered trademark of Carpenter Technologies, Readings, PA.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.