The presence of mechanical joints--typified by the lap joint--in otherwise linear structures has been accommodated in structural dynamics via ad hoc methods for a century. The methods range from tuning linear models to approximate non-linear behavior in restricted load ranges to various methods which introduce joint dissipation in a post-processing stage. Other methods, employing constitutive models for the joints are being developed and their routine use is on the horizon.
We have measured the temperature dependence of mechanical dissipation in tetrahedral amorphous carbon flexural and torsional resonators over the temperature range from 300 to 1023 K. The mechanical dissipation was found to be controlled by defects within the material, and the magnitude and temperature dependence of the dissipation were found to depend on whether flexural or torsional vibrational modes were excited. The defects that were active under flexural stresses have a relatively flat concentration from 0.4 to 0.7 eV with an ever increasing defect concentration up to 1.9 eV. Under shear stresses (torsion), the defect activation energies increase immediately beginning at 0.4 eV, with increasing defect concentration at higher energies.
Solid solutions of lead-based perovskites are the backbone materials of the piezoelectric components for transducer, actuator, and resonator applications. These components, typically small in size, are fabricated from large sintered ceramic slugs using grinding and lapping processes. These operations increase manufacturing costs and produce a large hazardous waste stream, especially when component size decreases. To reduce costs and hazardous wastes associated with the production of these components, an injection molding technique is being investigated to replace the machining processes. The first step in the new technique is to compound an organic carrier with a ceramic powder. The organic carrier is a thermoplastic based system composed of a main carrier, a binder, and a surfactant. Understanding the rheology of the compounded material is necessary to minimize the creation of defects such as voids or cavities during the injection-molding process. An experiment was performed to model the effects of changes in the composition and processing of the material on the rheological behavior. Factors studied included: the surfactant of the organic carrier system, the solid loading of the compounded material, and compounding time. The effects of these factors on the viscosity of the material were investigated.
We report the experimental realization of a new type of optical parametric oscillator in which oscillation is achieved by polarization rotation in a linear retarder, followed by nonlinear polarization mixing. The mixing is performed by a type II degenerate parametric downconversion in a periodically poled KTP crystal pumped by a 1064 nm pulsed Nd:YAG pump. A single, linearly polarized beam, precisely at the degenerate wavelength is generated. The output spectrum has a narrow linewidth (below the instrumentation bandwidth of 1 nm) and is highly stable with respect to variations in the crystal temperature.
Concepts from Complexity Science are valuable and allow a simulation approach for critical infrastructures that is flexible and has wide ranging applications.
A large-scale field demonstration comparing final landfill cover designs was constructed and monitored at Sandia National Laboratories in Albuquerque, New Mexico. Two conventional designs (a RCRA Subtitle 'D' Soil Cover and a RCRA Subtitle 'C' Compacted Clay Cover) were constructed side-by-side with four alternative cover test plots designed for arid environments. The demonstration was intended to evaluate the various cover designs based on their respective water balance performance, ease and reliability of construction, and cost. A portion of this project involves the characterization of vegetation establishment and growth on the landfill covers. The various prototype landfill covers were expected to have varying flux rates (Dwyer et al 2000). The landfill covers were further expected to influence vegetation establishment and growth, which may impact site erosion potential and long-term site integrity. Objectives of this phase were to quantify the types of plants occupying each site, the percentage of ground covered by these plants, the density (number of plants per unit area) of plants, and the plant biomass production. The results of this vegetation analysis are presented in this report.3 DRAFT07/06/14AcknowledgementsWe would like to thank all technical and support staff from Sandia and the USDA Forest Service's Rocky Mountain Station not included in the authors' list of this document for their valuable contributions to this research. We would also like to acknowledge the Department of Energy's Subsurface Contaminants Focus Area for funding this work.4
This Work Plan identifies and outlines interim measures to address nitrate contamination in groundwater at the Burn Site, Sandia National Laboratories/New Mexico. The New Mexico Environment Department has required implementation of interim measures for nitrate-contaminated groundwater at the Burn Site. The purpose of interim measures is to prevent human or environmental exposure to nitrate-contaminated groundwater originating from the Burn Site. This Work Plan details a summary of current information about the Burn Site, interim measures activities for stabilization, and project management responsibilities to accomplish this purpose.
We show that the orientation of pentacene molecules is controlled by the electronic structure of the surface on which they are deposited. We suggest that the near-Fermi level density of states above the surface controls the interaction of the substrate with the pentacene {pi} orbitals. A reduction of this density as compared to noble metals, realized in semimetallic Bi(001) and Si(111)(5 x 2)Au surfaces, results in pentacene standing up. Interestingly, pentacene grown on Bi(001) is highly ordered, yielding the first vertically oriented epitaxial pentacene thin films observed to date.
