Publications

Abstract not provided.

The intense magnetic field generated in the 20 MA Z-machine is used to accelerate metallic flyer plates to high velocity for the purpose of generating strong shocks in equation of state experiments. We present results pertaining to experiments in which a 0.085 cm thick Al flyer plate is magnetically accelerated across a vacuum gap into a quartz target. Peak magnetic drive pressures up to 4.9 Mbar were produced, which yielded a record 34 km/s flyer velocity without destroying it by shock formation or Joule heating. Two-dimensional MHD simulation was used to optimize the magnetic drive pressure on the flyer surface, shape the current pulse to accelerate the flyer without shock formation (i.e., quasi-isentropically), and predict the flyer velocity. Shock pressures up to 11.5 Mbar were produced in quartz. Accurate measurements of the shock velocity indicate that a fraction of the flyer is at solid density when it arrives at the target. Comparison of measurements and simulation results yields a consistent picture of the flyer state at impact with the quartz target.

We present Density Functional Theory (DFT) calculations of water in a region of phase space of interest in shock experiments. The onset of electrical conductivity in shocked water is determined by ionic conductivity, with the electron contribution dominating at higher pressures. The ionic contribution to the conduction is calculated from proton diffusion (Green-Kubo formula) and the electronic contribution is calculated using the Kubo-Greenwood formula [1]. The calculations are performed with VASP, a plane-wave pseudopotential code. At 2000K and a density of 2.3 g/cc, we find a significant dissociation of water into H, OH, and H3O, not only intermittent formation of OH - H3O pairs as suggested earlier for 2000 K and 1.95 g/cc [2]. The calculated conductivity is compared to experimental data [3]. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Safety Administration under contract DE-AC04-94AL85000. This project was supported by the Sandia LDRD office. [1] M. P. Desjarlais, J. D. Kress, and L. A. Collins; Phys. Rev. B 66, 025401 (2002). [2] E. Schwegler, et al. Phys. Rev. Lett. 87, 265501 (2001). [3] P.M. Celliers, et. al. Physics of Plasmas 11, L41 (2004).

Abstract not provided.

Abstract not provided.

This paper describes the photonic component development, which exploits pioneering work and unique expertise at Sandia National Laboratories, ARDEC and the Army Research Laboratory by combining key optoelectronic technologies to design and demonstrate components for this fuzing application. The technologies under investigation for the optical fuze design covered in this paper are vertical cavity surface emitting lasers (VECSELs), integrated resonant cavity photodetectors (RCPD), and diffractive micro-optics. The culmination of this work will be low cost, robust, fully integrated, g-hardened components designed suitable for proximity fuzing applications. The use of advanced photonic components will enable replacement of costly assemblies that employ discrete lasers, photodetectors, and bulk optics. The integrated devices will be mass produced and impart huge savings for a variety of Army applications.

Abstract not provided.

Abstract not provided.

Abstract not provided.

A suite of impact experiments was conducted to assess spatial and shot-to-shot variability in dynamic properties of tantalum. Samples had a uniform refined {approx}20 micron grain structure with a strong axisymmetric [111] crystallographic texture. Two experiments performed with sapphire windows (stresses of approximately 7 and 12 GPa) clearly showed elastic-plastic loading and slightly hysteretic unloading behavior. An HEL amplitude of 2.8 GPa (corresponding to Y 1.5 GPa) was observed. Free-surface spall experiments showed clear wave attenuation and spallation phenomena. Here, loading stresses were {approx} 12.5 GPa and various ratios of impactor to target thicknesses were used. Spatial and shot-to-shot variability of the spall strength was {+-} 20%, and of the HEL, {+-} 10%. Experiments conducted with smaller diameter flyer plates clearly showed edge effects in the line and point VISAR records, indicating lateral release speeds of roughly 5 km/s.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Spectroscopic investigations in the visible and near UV are underway to study plasmas present in X-ray radiography diodes during the time of the electron beam propagation. These studies are being performed on the RITS-3 accelerator (5.25 MV and 120 kA) at Sandia National Laboratories using several diode configurations. The proper characterization of the plasmas occurring during the time of the X-ray pulse can lead to a greater understanding of diode behavior and X-ray spot size evolution. By studying these plasmas along with the use of selective dopants, insights into such phenomena as impedance collapse, thermal and non-thermal species behavior, charge and current neutralization, anode and cathode plasma formation and propagation, and beam/foil interactions, can be obtained. Information from line and continuum emission and absorption can give key plasma parameters such as temperatures, densities, charge states, and expansion velocities. This information is important for proper modeling and future predictive capabilities for the design and improvement of flash X-ray radiography diodes. Diagnostics include a gated, intensified multichannel plate camera combined with a 1 meter Czerny-Turner monochromator with a multi-fiber spectral input, allowing for both temporal and spatial resolution. Recent results are presented.

Single layer transition metal sulfides (SLTMS) such as MoS{sub 2}, WS{sub 2}, and ReS{sub 2}, play an important role in catalytic processes such as the hydrofining of petroleum streams, and are involved in at least two of the slurry-catalyst hydroconversion processes that have been proposed for upgrading heavy petroleum feed and other sources of hydrocarbon fuels such as coal and shale oils. Additional promising catalytic applications of the SLTMS are on the horizon. The physical, chemical, and catalytic properties of these materials are reviewed in this report. Also discussed are areas for future research that promise to lead to advanced applications of the SLTMS.

Abstract not provided.

The magnetically immersed (B{sub z}) diode is being investigated as a source for pulsed-power driven flash radiography. Experiments fielding this diode have revealed a limit on its achievable current density on target. Either a small spot produces a low dose, or a high dose is achieved with a large spot. It has been proposed that this limit is due to non-protonic ions liberated from the anode surface and subsequently ionizing to higher states. The three-dimensional particle-in-cell code LSP is used to investigate this proposal. Data from the recent immersed diode experiments conducted on the RITS-3 accelerator are compared to LSP models of the experimental configuration, including the B{sub z} field map. We report on how the non-protonic and protonic ion models compare to data, and proposals for future investigation.

Controlled seeding of perturbations is employed to study the evolution of wire array z-pinch implosion instabilities which strongly impact x-ray production when the 3D plasma stagnates on axis. Wires modulated in radius exhibit locally enhanced magnetic field and imploding bubble formation at discontinuities in wire radius due to the perturbed current path. Wires coated with localized spectroscopic dopants are used to track turbulent material flow. Experiments and MHD modeling offer insight into the behavior of z-pinch instabilities.

Experiments to study the implosion dynamics and radiation characteristics of copper z-pinches have been fielded at the 1 MA Zebra facility and the 20 MA Z facility. The impact of initial load mass, initial load diameter, and nesting of wire arrays on the precursor and the stagnated plasma has been evaluated through spectroscopy, shadowgraphy, and fluence measurements. Plasma parameters extracted from modeling of the time-integrated L-shell spectra indicate the presence of more than one plasma source contributing to the radiation, likely due to non-uniform hot spot x-ray emission or temporal gradients.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Over the last several years, rapid progress has been made evaluating the double-z-pinch indirect-drive, inertial confinement fusion (ICF) high-yield target concept (Hammer et al 1999 Phys. Plasmas 6 2129). We have demonstrated efficient coupling of radiation from two wire-array-driven primary hohlraums to a secondary hohlraum that is large enough to drive a high yield ICF capsule. The secondary hohlraum is irradiated from two sides by z-pinches to produce low odd-mode radiation asymmetry. This double-pinch source is driven from a single electrical power feed (Cuneo et al 2002 Phys. Rev. Lett. 88 215004) on the 20 MA Z accelerator. The double z-pinch has imploded ICF capsules with even-mode radiation symmetry of 3.1 {+-} 1.4% and to high capsule radial convergence ratios of 14-21 (Bennett et al 2002 Phys. Rev. Lett. 89 245002; Bennett et al 2003 Phys. Plasmas 10 3717; Vesey et al 2003 Phys. Plasmas 10 1854). Advances in wire-array physics at 20 MA are improving our understanding of z-pinch power scaling with increasing drive current. Techniques for shaping the z-pinch radiation pulse necessary for low adiabat capsule compression have also been demonstrated.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The evolution of granular shear flow is investigated as a function of height in a split-bottom Couette cell. Using particle tracking, magnetic-resonance imaging, and large-scale simulations, we find a transition in the nature of the shear as a characteristic height H* is exceeded. Below H* there is a central stationary core; above H* we observe the onset of additional axial shear associated with torsional failure. Radial and axial shear profiles are qualitatively different: the radial extent is wide and increases with height, while the axial width remains narrow and fixed.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The use of Ion Mobility Spectrometry (IMS) in the Detection of Contraband Sandia researchers use ion mobility spectrometers for trace chemical detection and analysis in a variety of projects and applications. Products developed in recent years based on IMS-technology include explosives detection personnel portals, the Material Area Access (MAA) checkpoint of the future, an explosives detection vehicle portal, hand-held detection systems such as the Hound and Hound II (all 6400), micro-IMS sensors (1700), ordnance detection (2500), and Fourier Transform IMS technology (8700). The emphasis to date has been on explosives detection, but the detection of chemical agents has also been pursued (8100 and 6400). Combining Ion Mobility Spectrometry (IMS) with Mass Spectrometry (MS) is described. The IMS-MS combination overcomes several limitations present in simple IMS systems. Ion mobility alone is insufficient to identify an unknown chemical agent. Collision cross section, upon which mobility is based, is not sufficiently unique or predictable a priori to be able to make a confident peak assignment unless the compounds present are already identified. Molecular mass, on the other hand, is much more readily interpreted and related to compounds. For a given compound, the molecular mass can be determined using a pocket calculator (or in one's head) while a reasonable value of the cross-section might require hours of computation time. Thus a mass spectrum provides chemical specificity and identity not accessible in the mobility spectrum alone. In addition, several advanced mass spectrometric methods, such as tandem MS, have been extensively developed for the purpose of molecular identification. With an appropriate mass spectrometer connected to an ion mobility spectrometer, these advanced identification methods become available, providing greater characterization capability.

Sedimentary basins can increase the magnitude and extend the duration of seismic shaking. This potential for seismic amplification is investigated for Pahrump Valley, Nevada-California. The Pahrump Valley is located approximately 50 km northwest of Las Vegas and 75 km south of the Nevada Test Site. Gravity data suggest that the city of Pahrump sits atop a narrow, approximately 5 km deep sub-basin within the valley. The seismic amplification, or ''site effect'', was investigated using a combination of in situ velocity modeling and comparison of the waveforms and spectra of weak ground motion recorded in the city of Pahrump, Nevada, and those recorded in the nearby mountains. Resulting spectral ratios indicate seismic amplification factors of 3-6 over the deepest portion of Pahrump Valley. This amplification predominantly occurs at 2-2.5 Hz. Amplification over the deep sub-basin is lower than amplification at the sub-basin edge, location of the John Blume and Associates PAHA seismic station, which recorded many underground nuclear tests at the Nevada Test Site. A comprehensive analysis of basin amplification for the city of Pahrump should include 3-D basin modeling, due to the extreme basement topography of the Pahrump Valley.

This report describes results of tests using a laser system designed by Coherent Technologies, Inc., in conjunction with Sandia developed nonlinear optics technology. Test results are described for three different optical parametric oscillators built at Sandia. The report concludes with recommendations for future work.

We report low-dimensional transport and tunneling in an independently contacted vertically coupled quantum wire system, with a 7.5 nm barrier between the wires. The derivative of the linear conductance shows evidence for both single wire occupation and coupling between the wires. This provides a map of the subband occupation that illustrates the control that we have over the vertically coupled double quantum wires. Preliminary tunneling results indicate a sharp 1D-1D peak in conjunction with a broad 2D-2D background signal. This 1D-1D peak is sensitively dependent on the top and bottom split gate voltage. © 2005 American Institute of Physics.

The temperature dependence of the resistivity and magnetoresistance of dilute 2D electrons are reported. The temperature dependence of the resistivity can be qualitatively described through phonon and ionized impurity scattering. While the temperature dependence indicates no ln(T) increase in the resistance, a sharp negative magnetoresistance feature is observed at small magnetic fields. This is shown to arise from weak localization. At very low density, we believe weak localization is still present, but cannot separate it from other effects that cause magnetoresistance in the semi-classical regime. © 2005 American Institute of Physics.

Collective impact ionization has been used to explain lock-on, an optically-triggered electrical breakdown occurring in some photoconductive semiconductor switches (PCSS's). Lock-on is observed in GaAs and InP but not in Si or GaP. Here, a rate equation implementation of collective impact ionization is discussed, and it leads to new insights both about intrinsic electrical breakdown in insulating materials in general and about lock-on specifically. In this approach, lock-on and electrical breakdown are steady state processes controlled by competition between carrier generation and recombination. This leads to theoretical definitions for both the lock-on field and the breakdown field. Our results show that lock-on is a carrier-density dependent form of electrical breakdown which exists in principle in all semiconductors. Results for GaAs, InP, Si, and GaP are discussed. © 2005 American Institute of Physics.