Residual stress is a contributor to stress corrosion cracking (SCC) and a common byproduct of additive manufacturing (AM). Here the relationship between residual stress and SCC susceptibility in laser powder bed fusion AM 316L stainless steel was studied through immersion in saturated boiling magnesium chloride per ASTM G36-94. The residual stress was varied by changing the sample height for the as-built condition and additionally by heat treatments at 600°C, 800°C, and 1,200°C to control, and in some cases reduce, residual stress. In general, all samples in the as-built condition showed susceptibility to SCC with the thinner, lower residual stress samples showing shallower cracks and crack propagation occurring perpendicular to melt tracks due to local residual stress fields. The heat-treated samples showed a reduction in residual stress for the 800°C and 1,200°C samples. Both were free of cracks after >300 h of immersion in MgCl2, while the 600°C sample showed similar cracking to their as-built counterpart. Geometrically necessary dislocation (GND) density analysis indicates that the dislocation density may play a major role in the SCC susceptibility.
This report provides detailed documentation of the algorithms that where developed and implemented in the Plato software over the course of the Optimization-based Design for Manufacturing LDRD project.
This study employs nonlinear ultrasonic techniques to track microstructural changes in additively manufactured metals. The second harmonic generation technique based on the transmission of Rayleigh surface waves is used to measure the acoustic nonlinearity parameter, β. Stainless steel specimens are made through three procedures: traditional wrought manufacturing, laser-powder bed fusion, and laser engineered net shaping. The β parameter is measured through successive steps of an annealing heat treatment intended to decrease dislocation density. Dislocation density is known to be sensitive to manufacturing variables. In agreement with fundamental material models for the dislocation-acoustic nonlinearity relationship in the second harmonic generation, β drops in each specimen throughout the heat treatment before recrystallization. Geometrically necessary dislocations (GNDs) are measured from electron back-scatter diffraction as a quantitative indicator of dislocations; average GND density and β are found to have a statistical correlation coefficient of 0.852 showing the sensitivity of β to dislocations in additively manufactured metals. Moreover, β shows an excellent correlation with hardness, which is a measure of the macroscopic effect of dislocations.
We develop a generalized stress inversion technique (or the generalized inversion method) capable of recovering stresses in linear elastic bodies subjected to arbitrary cuts. Specifically, given a set of displacement measurements found experimentally from digital image correlation (DIC), we formulate a stress estimation inverse problem as a partial differential equation-constrained optimization problem. We use gradient-based optimization methods, and we accordingly derive the necessary gradient and Hessian information in a matrix-free form to allow for parallel, large-scale operations. By using a combination of finite elements, DIC, and a matrix-free optimization framework, the generalized inversion method can be used on any arbitrary geometry, provided that the DIC camera can view a sufficient part of the surface. We present numerical simulations and experiments, and we demonstrate that the generalized inversion method can be applied to estimate residual stress.
Fe-Co-2V is a popular metallic alloy used in electromagnetic applications. However, there is a lack of mechanical fatigue characterization of this alloy in the literature. In this work, Fe-Co-2V specimens with rectangular cross-sections were carefully prepared in accordance with standards. They were measured for surface roughness and then subjected to quasi-static monotonic testing, as well as fatigue testing at both 0.5 Hz and 1 Hz frequencies. Both Rockwell hardness and Vickers micro- hardness testing were performed. Additionally, scanning electron microscopy imaging of the fractured surfaces was done. The quasi-static testing revealed a flat yield region characteristic of Laders bands. Here, the fatigue results did not show significant differences or sensitivity to change in frequency, although the fatigue life was higher on average for the 0.5 Hz. However, the fatigue results differed from published work at 0.33 Hz. The fractography revealed purely brittle fracture, with clear chevron marks and fracture initiation always starting at the surface. Lastly, it was identified that the C, D, and F Rockwell hardness scales were appropriate for testing this material and that the grain size necessitated the use of the upper end of indentation force for Vickers micro-hardness testing.
Predicting performance of parts produced using laser-metal processing remains an out- standing challenge. While many computational models exist, they are generally too computationally expensive to simulate the build of an engineering-scale part. This work develops a reduced order thermal model of a laser-metal system using analytical Green's function solutions to the linear heat equation, representing a step towards achieving a full part performance prediction in an "overnight" time frame. The developed model is able to calculate a thermal history for an example problem 72 times faster than a traditional FEM method. The model parameters are calibrated using a non-linear solution and microstructures and residual stresses calculated and compared to a non-linear case. The calibrated model shows promising agreement with a non-linear solution.
Residual stress measurements using neutron diffraction and the contour method were performed on a valve housing made from 316 L stainless steel powder with intricate three-dimensional internal features using laser powder-bed fusion additive manufacturing. The measurements captured the evolution of the residual stress fields from a state where the valve housing was attached to the base plate to a state where the housing was cut free from the base plate. Making use of this cut, thus making it a non-destructive measurement in this application, the contour method mapped the residual stress component normal to the cut plane (this stress field is completely relieved by cutting) over the whole cut plane, as well as the change in all stresses in the entire housing due to the cut. The non-destructive nature of the neutron diffraction measurements enabled measurements of residual stress at various points in the build prior to cutting and again after cutting. Good agreement was observed between the two measurement techniques, which showed large, tensile build-direction residual stresses in the outer regions of the housing. The contour results showed large changes in multiple stress components upon removal of the build from the base plate in two distinct regions: near the plane where the build was cut free from the base plate and near the internal features that act as stress concentrators. These observations should be useful in understanding the driving mechanisms for builds cracking near the base plate and to identify regions of concern for structural integrity. Neutron diffraction measurements were also used to show the shear stresses near the base plate were significantly lower than normal stresses, an important assumption for the contour method because of the asymmetric cut.
Additive Manufacturing (AM) presents unprecedented opportunities to enable design freedom in parts that are unachievable via conventional manufacturing. However, AM-processed components generally lack the necessary performance metrics for widespread commercial adoption. We present a novel AM processing and design approach using removable heat sink artifacts to tailor the mechanical properties of traditionally low strength and low ductility alloys. The design approach is demonstrated with the Fe-50 at.% Co alloy, as a model material of interest for electromagnetic applications. AM-processed components exhibited unprecedented performance, with a 300 % increase in strength and an order-of-magnitude improvement in ductility relative to conventional wrought material. These results are discussed in the context of product performance, production yield, and manufacturing implications toward enabling the design and processing of high-performance, next-generation components, and alloys.
Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s−1 and temperatures from − 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.
Fe-Co-2V is a soft ferromagnetic alloy used in electromagnetic applications due to excellent magnetic properties. However, the discontinuous yielding (Luders bands), grain-size-dependent properties (Hall-Petch behavior), and the degree of order/disorder in the Fe-Co-2V alloy makes it difficult to predict the mechanical performance, particularly in abnormal environments such as elevated strain rates and high/low temperatures. Thus, experimental characterization of the high strain rate properties of the Fe-Co-2V alloy is desired, which are used for material model development in numerical simulations. In this study, the high rate tensile response of Fe-Co-2V is investigated with a pulse-shaped Kolsky tension bar over a wide range of strain rates and temperatures. Effects of temperature and strain rate on yield stress, ultimate stress, and ductility are discussed.