Three dimensional steady shear simulations of electrorheology (ER) and magnetorheology (MR) in a uniaxial field are presented and included the effects of Brownian motion. The shear thinning viscosity was observed in the absence of thermal fluctuations. The fluid stress decreased, especially at low Mason numbers, as the influence of Brownian motion increased. A microscopic chain model of the role played by thermal fluctuations on the rheology of ER and MR fluids was proposed.
A series of fine-grained porous alumina samples, with and without a liquid phase, were fabricated in compositions matched closely to commercially available alumina used as microelectronic substrates. Hertzian indentation on monolithic specimens of the glass-containing samples produced a greater quasi-ductile stress-strain response compared with that observed in the pure alumina. Maximum residual indentation depths, determined from surface profilometry, correlated with the stress-strain results. Moreover, microstructural observations from bonded interface specimens revealed significantly more damage in the form of microcracking and under extreme loading, pore collapse, in the glass-containing specimens. The absence of the typical twin faulting mechanism observed for larger-grained alumina suggests that the damage mechanism for quasi-ductility in these fine-grained porous aluminas was derived from the pores acting as a stress concentrator and the grain boundary glass phase providing a weak path for short crack propagation.
The Long-term Inflow and Structural Test (LIST) program is collecting long-term, continuous inflow and structural response data to characterize the extreme loads on wind turbines. A heavily instrumented Micon 65/13M turbine with SERI 8m blades is being used as the primary test turbine for this test series. This turbine is located in Bushland, TX, a test site that exposes the turbine to a wind regime that is representative of a Great Plains commercial site. The turbine and its inflow are being characterized with 60 measurements: 34 to characterize the inflow, 19 to characterize structural response, and 7 to characterize the time-varying state of the turbine. In a companion paper, Sutherland, Jones and Neal1 give a detailed description of the turbine, the site and the instrumentation. In this paper, a preliminary analysis of the structural and inflow data is presented. Particular attention is paid to the determination of the various structural loads on the turbine. Long-term fatigue spectra are also presented.
Chemically prepared Pb(Zr0.95Ti0.05)O3 (PZT 95/5) ceramics were fabricated with a range of different porosity levels, while grain size was held constant, by systematic additions of added organic pore former (Avicel). Use of Avicel in amounts ranging from 0 to 4.0 wt% resulted in fired ceramic densities that ranged from 97.3% to 82.3%. Hydrostatic-pressure-induced ferroelectric (FE) to antiferroelectric (AFE) phase transformations were substantially more diffuse and occurred at lower hydrostatic pressures with increasing porosity. An ∼12 MPa decrease in hydrostatic transformation pressure per volume percent added porosity was observed. The decrease in transformation pressure with decreasing density was quantitatively consistent with the calculated macroscopic stress required to achieve a specific volumetric macrostrain (0.40%). This strain was equivalent to experimentally measured macrostrain for FE-to-AFE transformation. The macroscopic stress levels were calculated using measured bulk modulus values that decreased from 84 to 46 GPa as density decreased from 97.3% to 82.3%. Good agreement between calculated and measured values of FE-to-AFE transformation stress was obtained for ceramics fired at 1275° and 1345°C.
The wavelength variation of the second-order nonlinear coefficients of KNbO3, KH2PO4 and LiB3O5 crystals was discussed. The second-order nonlinear coefficients were measured using optical parametric amplification and second-harmonic generation over a wide range of wavelengths for the crystals. The results showed that Miller scaling was a useful approximation for the crystals.
A kinetic, three-dimensional Monte Carlo model for simulating grain growth in the presence of mobile pores is presented. The model was used to study grain growth and pore migration by surface diffusion in an idealized geometry that ensures constant driving force for grain growth. The driving forces, pore size, and pore mobilities were varied to study their effects on grain-boundary mobility and grain growth. The simulations captured a variety of complex behaviors, including reduced grain-boundary velocity due to pore drag that has been predicted by analytical theories. The model is capable of treating far more complex geometries, including polycrystals. We present the capabilities of this model and discuss its limitations.
The Long-term Inflow and Structural Test (LIST) program is collecting long-term, continuous inflow and structural response data to characterize the extreme loads on wind turbines. A heavily instrumented Micon 65/13M turbine with SERI 8-m blades is being used as the first test turbine for this program. This turbine and its two sister turbines are located in Bushland, TX, a test site that exposes the turbines to a wind regime that is representative of a Great Plains commercial site. The turbines and their inflow are being characterized with 60 measurements: 34 to characterize the inflow, 19 to characterize structural response, and 7 to characterize the time-varying state of the turbine. The primary characterization of the inflow into the LIST turbine relies upon an array of five sonic anemometers. Primary characterization of the structural response of the turbine uses several sets of strain gauges to measure bending loads on the blades and the tower and two accelerometers to measure the motion of the nacelle. Data from the various instruments are sampled at a rate of 30 Hz using a newly developed data acquisition system that features a time-synchronized continuous data stream that is telemetered from the turbine rotor. The data, taken continuously, are automatically divided into 10-minute segments and archived for analysis. Preliminary data are presented to illustrate the operation of the turbine and the data acquisition and analysis system.
This paper describes a system, which acquires 3D data and tracks an eleven degree of freedom human model in real-time. Using four cameras we create a time-varying volumetric image (a visual hull) of anything moving in the space observed by all four cameras. The sensor is currently operating in a volume of approximately 500,000 voxels (1.5 inch cubes) at a rate of 25 Hz. The system is able to track the upper body dynamics of a human (x,y position of the body, a torso rotation, and four rotations per arm). Both data acquisition and tracking occur on one computer at a rate of 16 Hz. We also developed a calibration procedure, which allows the system to be moved and be recalibrated quickly. Furthermore we display in real-time, either the data overlaid with the joint locations or a human avatar. Lastly our system has been implemented to perform crane gesture recognition.
A new instrument to accurately and verifiably measure mechanical properties across an entire MEMS wafer is under development. We have modified the optics on a conventional microelectronics probe station to enable three-dimensional imaging while maintaining the full working distance of a long working distance objective. This allows standard probes or probe cards to be used. We have proceeded to map out mechanical properties of polycrystalline silicon along a wafer column by the Interferometry for Material Property Measurement (IMaP) methodology. From interferograms of simple actuated cantilevers, out-of-plane deflection profiles at the nanometer scale are obtained. These are analyzed by integrated software routines that extract basic mechanical properties such as cantilever curvature and Young's modulus. Non-idealities such as support post compliance and beam take off angle are simultaneously quantified. Curvature and residual stress are found to depend on wafer position. Although deflections of cantilevers varied across the wafer, Young's modulus E - 161 GPa is independent of wafer position as expected. This result is achieved because the non-idealities have been taken into account.
A low toxicity, high performance, hypergolic, bipropellant system is desired to replace conventional nitrogen tetroxide (NTO) and hydrazine propulsion systems. Hydrogen peroxide exothermically decomposes to water, and oxygen, making it an ideal oxidizer for more environmentally friendly propulsion systems. Unfortunately, the choice of fuel for such systems is not as clear. Many factors such as ignition delay, performance, toxicity, storability, and cost must be considered. Numerous candidate fuels and fuel/catalyst mixtures were screened using a simple laboratory setup and visual observation. A mixture of ethanolamine and 1% copper (II) chloride was found to rapidly ignite with 90% hydrogen peroxide. Hydrogen peroxide and ethanolamine are much less toxic than NTO and hydrazine. Hydrogen peroxide and ethanolamine have a calculated specific impulse of 245 seconds compared to 284 seconds for NTO and monomethyl hydrazine. A low-freezing blend of furfuryl alcohol (47.5%), ethanolamine (47.5%), and copper (II) chloride (5%) was successfully test fired in a small rocket engine with both 90% and 99% hydrogen peroxide. Hypergolic ignition of this mixture was achieved with 70% hydrogen peroxide. Our quest for a non-toxic hypergol began by researching the literature. Most current low freezing points, exhibit good performance, and are non-toxic compared to hydrazines.1 Unfortunately, hypergolic ignition was only achieved after adding a large amount (>10%) of manganese based catalyst.2-4 Metallic catalysts are toxic and impair performance, so low concentrations are desired. In addition, an insoluble catalyst may not remain in uniform suspension, converting a hypergolic fuel into one with inconsistent age related performance. We wanted to find a fuel that was hypergolic by itself, or that could be made so with a much smaller addition of metallic catalyst.
International standards for wind turbine certification depend on finding long-term fatigue load distributions that are conservative with respect to the state of knowledge for a given system. Statistical models of loads for fatigue application are described and demonstrated using flap and edge blade-bending data from a commercial turbine in complex terrain. Distributions of rainflow-counted range data for each ten-minute segment are characterized by parameters related to their first three statistical moments (mean, coefficient of variation, and skewness). Quadratic Weibull distribution functions based on these three moments are shown to match the measured load distributions if the non-damaging low-amplitude ranges are first eliminated. The moments are mapped to the wind conditions with a two-dimensional regression over ten-minute average wind speed and turbulence intensity. With this mapping, the short-term distribution of ranges is known for any combination of average wind speed and turbulence intensity. The long-term distribution of ranges is determined by integrating over the annual distribution of input conditions. First, we study long-term loads derived by integration over wind speed distribution alone, using standard-specified turbulence levels. Next, we perform this integration over both wind speed and turbulence distribution for the example site. Results are compared between standard-driven and site-driven load estimates. Finally, using statistics based on the regression of the statistical moments over the input conditions, the uncertainty (due to the limited data set) in the long-term load distribution is represented by 95% confidence bounds on predicted loads.
Helium-cooled, refractory heat exchangers are now under consideration for first wall and divertor applications. These refractory devices take advantage of high temperature operation with large delta-Ts to effectively handle high heat fluxes. The high temperature helium can then be used in a gas turbine for high-efficiency power conversion. Over the last five years, heat removal with helium was shown to increase dramatically by using porous metal to provide a very large effective surface area for heat transfer in a small volume. Last year, the thermal performance of a bare-copper, dual-channel, helium-cooled, porous metal divertor mock-up was evaluated on the 30 kW Electron Beam Test System at Sandia National Laboratories. The module survived a maximum absorbed heat flux of 34.6 MW/m2 and reached a maximum surface temperature of 593 °C for uniform power loading of 3 kW absorbed on a 2-cm2 area. An impressive 10 kW of power was absorbed on an area of 24 cm2. Recently, a similar dual-module, helium-cooled heat exchanger made almost entirely of tungsten was designed and fabricated by Thermacore, Inc. and tested at Sandia. A complete flow test of each channel was performed to determine the actual pressure drop characteristics. Each channel was equipped with delta-P transducers and platinum resistance temperature devices (RTDs) for independent calorimetry. One mass flow meter monitored the total flow to the heat exchanger, while a second monitored flow in only one of the channels. The thermal response of each tungsten module was obtained for heat fluxes in excess of 5 MW/m2 using 50 °C helium at 4 MPa. Fatigue cycles were also performed to assess the fracture toughness of the tungsten modules. A description of the module design and new results on flow instabilities are also presented.
In manufacturing, the conceptual design and detailed design stages are typically regarded as sequential and distinct. Decisions made in conceptual design are often made with little information as to how they would affect detailed design or manufacturing process specification. Many possibilities and unknowns exist in conceptual design where ideas about product shape and functionality are changing rapidly. Few if any tools exist to aid in this difficult, amorphous stage in contrast to the many CAD and analysis tools for detailed design where much more is known about the final product. The Materials Process Design Environment (MPDE) is a collaborative problem solving environment (CPSE) that was developed so geographically dispersed designers in both the conceptual and detailed stage can work together and understand the impacts of their design decisions on functionality, cost and manufacturability.
Adhesively-bonded joints of LaRC™ PETI-5, a phenylethynyl-terminated polyimide, with chromic acid anodized titanium were fabricated and debonded interfacially. The adhesive-substrate failure surfaces were investigated using several surface analysis techniques. From Auger spectroscopy, field emission scanning electron microscopy, and atomic force microscopy studies, polymer appears to he penetrating the pores of the anodized substrate to a depth of approximately 100 nm. From X-ray photoelectron spectroscopy data, the polymer penetrating the pores appears to be in electrical contact with the titanium oxide, leading to differential charging. These analyses confirm that the polymer is becoming mechanically interlocked within the substrate surface.
The development of microsystems that merge biological materials with microfabricated structures is highly dependent on the successful interfacial interactions between these innately incompatible materials. Surface passivation of semiconductor and glass surfaces with thin organic films can attenuate the adhesion of proteins and cells that lead to biofilm formation and biofouling of fluidic structures. We have examined the adhesion of glial cells and serum albumin proteins to microfabricated glass and semiconductor surfaces coated with self-assembled monolayers (SAM) of octadecyltrimethoxysilane (OTMS) and N-(triethoxysilylpropyl)-O-polyethylene oxide urethane (TESP), to evaluate the biocompatibility and surface passivation those coatings provide. These films were exposed to solutions containing serum albumin proteins (4 mg/mL), glial cells in culturing media, and glial cells under fluid flow. While the OTMS surface resisted cell spreading and growth under culture conditions, the same surface induced biofouling in a cell flow experiment with a microfluidic structure. Interestingly, the TESP surface, which was supportive of cell adhesion and proliferation under cell culturing conditions, effectively passivated the microfluidic structure to cell adhesion and biofouling. The results suggest that the cell adhesion process is not only dependent on the chemistry of the surface but also on the time allotted to the cell to probe the surface.
InxGa1-xAs1-yNy quaternary alloys offer the promise of longer wavelength, ≥ 1.3 μm optical transceivers grown on GaAs substrates. To achieve acceptable radiative efficiencies at 1.3 μm, highly-strained InGaAsN quantum wells (x ≈ 0.4, y ≈ 0.005) are being developed as laser active regions. By introducing GaAsP layers into the active region for strain-compensation, gain can be increased using multiple InGaAsN quantum wells. In this work, we report the first strain-compensated, 1.3 μm InGaAsN MQW lasers. Our devices were grown by metal-organic chemical vapor deposition. Lasers with InGaAsN quantum well active regions are proving superior to lasers constructed with competing active region materials. Under pulsed operation, our 1.3 μm InGaAsN lasers displayed negligible blue-shift from the low-injection LED emission, and state-of-the-art characteristic temperature (159 K) was obtained for a 1.3 μm laser.
Recent advances in the development and application of self-assembly templating techniques have opened up the possibility of tailoring membranes for specific separation problems. A new self-assembly processing route to generate inorganic membrane films has made it feasible to finely control both the three-dimensional (3D) porosity and the chemical nature of the adsorbing structures. Chemical sites can be added to a porous membrane either after the inorganic scaffolding has been put in place or, alternatively, chemical sites can be co-assembled in a one-step process. To provide guidance to the optimized use of these 'designer' membranes we have developed a substantial modeling program that focuses on permeation through porous materials. The key issues that need to be modeled concern 1) the equilibrium adsorption behavior in a variety of 3D porous structures, ranging from straight pore channels to fractal structures, 2) the transport (i.e. diffusion) behavior in these structures. Enriching the problem is the presence of reactive groups that may be present on the surface. An important part of the design of actual membranes is to optimize these reactive sites with respect to their strength as characterized by the equilibrium constant, and the positioning of these sites on the adsorbing surface. What makes the technological problem challenging is that the industrial application requires both high flux and high selectivity. What makes the modeling challenging is the smallness of the length scale (molecular) that characterizes the surface reaction and the confinement in the pores. This precludes the use of traditional continuum engineering methods. However, we must also capture the 3D connectivity of the porous structure which is characterized by a larger than molecular length scale. We will discuss how we have used lattice models and both Monte Carlo and 3D density functional theory methods to tackle these modeling challenges.
Frictional energy dissipation in joints is an issue of long-standing interest in the effort to predict damping of built up structures. Even obtaining a qualitative understanding of how energy dissipation depends on applied loads has not yet been accomplished. Goodman[l] postulated that in harmonic loading, the energy dissipation per cycle would go as the cube of the amplitude of loading. Though experiment does support a power-law relationship, the exponent tends to be lower than Goodman predicted. Recent calculations discussed here suggest that the cause of that deviation has to with reshaping of the contact patch over each loading period.
We present and analyze a class of evolutionary algorithms for unconstrained and bound constrained optimization on R(n): evolutionary pattern search algorithms (EPSAs). EPSAs adaptively modify the step size of the mutation operator in response to the success of previous optimization steps. The design of EPSAs is inspired by recent analyses of pattern search methods. We show that EPSAs can be cast as stochastic pattern search methods, and we use this observation to prove that EPSAs have a probabilistic, weak stationary point convergence theory. This convergence theory is distinguished by the fact that the analysis does not approximate the stochastic process of EPSAs, and hence it exactly characterizes their convergence properties.
The ASTM standards provide guidance and instruction on how to field and interpret reactor dosimetry. They provide a roadmap towards understanding the current "state-of-the-art" in reactor dosimetry, as reflected by the technical community. The consensus basis to the ASTM standards assures the user of an unbiased presentation of technical procedures and interpretations of the measurements. Some insight into the types of standards and the way in which they are organized can assist one in using them in an expeditious manner. Two examples are presented to help orient new users to the breadth and interrelationship between the ASTM nuclear metrology standards. One example involves the testing of a new "widget" to verify the radiation hardness. The second example involves quantifying the radiation damage at a pressure vessel critical weld location through surveillance dosimetry and calculation.
This report describes the initial definition of the Verification and Validation (V and V) Plan Peer Review Process at Sandia National Laboratories. V and V peer review at Sandia is intended to assess the ASCI code team V and V planning process and execution. Our peer review definition is designed to assess the V and V planning process in terms of the content specified by the Sandia Guidelines for V and V plans. Therefore, the peer review process and process for improving the Guidelines are necessarily synchronized, and form parts of a larger quality improvement process supporting the ASCI V and V program at Sandia.
Application of the World Wide Web (WWW) for the transfer of sensor data from remote locations to laboratories and offices is a largely ignored application of the WWW. We have investigated several architectures for this application including simple web server/client architectures and variations of this approach. In addition, we have evaluated several commercial approaches and other techniques that have been investigated and are in the literature. Finally, we have provided conclusions based on the results of our study offering suggestions about the advantages and disadvantages of each of the approaches studied.
This primer presents a succinct summary of the evolution of U.S. nuclear deterrence policy from the initial development of nuclear weapons until the present day. This is not a definitive history but an introduction to deterrence policy for those with limited background in this area. The concept of deterrence is discussed in several ways--in a general description of deterrence theory, in an historical review of nuclear policy evolution, in a discussion of the future of deterrence, in historical examples of deterrence successes and failures, and in a review of significant contributors to the study of nuclear policy. The intent is to present an authoritative, unclassified account. To accomplish this, to the extent possible, primary source documents were located and utilized if they were available and declassified. These included unclassified Presidential nuclear policy guidance from the Presidential libraries, official JCS histories and State Department Foreign Relations histories. The writings of noted nuclear strategists and historians were also valuable resources for this primer on U.S. strategic nuclear policy.
A set of vertical extension fractures, striking N-S to NNE-SSW but with local variations, is present in both the outcrop and subsurface in both Mesaverde and Dakota sandstones. Additional sets of conjugate shear fractures have been recognized in outcrops of Dakota strata and may be present in the subsurface. However, the deformation bands prevalent locally in outcrops in parts of the basin as yet have no documented subsurface equivalent. The immature Mesaverde sandstones typically contain relatively long, irregular extension fractures, whereas the quartzitic Dakota sandstones contain short, sub-parallel, closely spaced, extension fractures, and locally conjugate shear planes as well. Outcrops typically display secondary cross fractures which are rare in the subsurface, although oblique fractures associated with local structures such as the Hogback monocline may be present in similar subsurface structures. Spacings of the bed-normal extension fractures are approximately equal to or less than the thicknesses of the beds in which they formed, in both outcrop and subsurface. Fracture intensities increase in association with faults, where there is a gradation from intense fracturing into fault breccia. Bioturbation and minimal cementation locally inhibited fracture development in both formations, and the vertical limits of fracture growth are typically at bedding/lithology contrasts. Fracture mineralizations have been largely dissolved or replaced in outcrops, but local examples of preserved mineralization show that the quartz and calcite common to subsurface fractures were originally present in outcrop fractures. North-south trending compressive stresses created by southward indentation of the San Juan dome area (where Precambrian rocks are exposed at an elevation of 14,000 ft) and northward indentation of the Zuni uplift, controlled Laramide-age fracturing. Contemporaneous right-lateral transpressive wrench motion due to northeastward translation of the basin was both concentrated at the basin margins (Nacimiento uplift and Hogback monocline on east and west edges respectively) and distributed across the strata depth.
This LDRD is aimed to place Sandia at the forefront of GaN-based technologies. Two important themes of this LDRD are: (1) The demonstration of novel GaN-based devices which have not yet been much explored and yet are coherent with Sandia's and DOE's mission objectives. UV optoelectronic and piezoelectric devices are just two examples. (2) To demonstrate front-end monolithic integration of GaN with Si-based microelectronics. Key issues pertinent to the successful completion of this LDRD have been identified to be (1) The growth and defect control of AlGaN and GaN, and (2) strain relief during/after the heteroepitaxy of GaN on Si and the separation/transfer of GaN layers to different wafer templates.
The free volume distribution has been a qualitatively useful concept by which dynamical properties of polymers, such as the penetrant diffusion constant, viscosity, and glass transition temperature, could be correlated with static properties. In an effort to put this on a more quantitative footing, we define the free volume distribution as the probability of finding a spherical cavity of radius R in a polymer liquid. This is identical to the insertion probability in scaled particle theory, and is related to the chemical potential of hard spheres of radius R in a polymer in the Henry's law limit. We used the Polymer Reference Interaction Site Model (PRISM) theory to compute the free volume distribution of semiflexible polymer melts as a function of chain stiffness. Good agreement was found with the corresponding free volume distributions obtained from MD simulations. Surprisingly, the free volume distribution was insensitive to the chain stiffness, even though the single chain structure and the intermolecular pair correlation functions showed a strong dependence on chain stiffness. We also calculated the free volume distributions of polyisobutylene (PIB) and polyethylene (PE) at 298K and at elevated temperatures from PRISM theory. We found that PIB has more of its free volume distributed in smaller size cavities than for PE at the same temperature.
Engineers at Sandia National Laboratories are combining entertainment industry software with traditional data collection techniques to create an interactive visualization tool. By replacing the usual flight simulator joystick with a telemetry data stream, experimental data is combined with existing three-dimensional (3D) engineering models. Users are immersed in their experiment, allowing interaction with and comprehension of complex data sets. Software tools are currently under development for post flight data visualization, and their usefulness and reusability have been demonstrated on numerous spaced-based programs within Sandia. However, data from remote sensors are subject to transmission errors that yield nonphysical behavior in real-time data visualization applications. We propose to investigate the applicability of real-time processing algorithms and estimation theories, such as Kalman filters, that have been successfully applied in other fields. Results will be integrated into existing postflight visualization tools for Proof-of-Concept validation and for potential integration of real-time applications.
Double-diffusive finger convection is a hydrodynamic instability that can occur when two components with different diffusivities are oppositely stratified with respect to the fluid density gradient as a critical condition is exceeded. Laboratory experiments were designed using sodium chloride and sucrose solutions in a Hele-Shaw cell. A high resolution, full field, light transmission technique was used to study the development of the instability. The initial buoyancy ratio (R{sub p}), which is a ratio of fluid density contributions by the two solutes, was varied systematically in the experiments so that the range of parameter space spanned conditions that were nearly stable (R{sub p} = 2.8) to those that were moderately unstable (R{sub p} = 1.4). In systems of low R{sub p}, fingers develop within several minutes, merge with adjacent fingers, form conduits, and stall before newer-generated fingers travel through the conduits and continue the process. Solute fluxes in low R{sub p} systems quickly reach steady state and are on the order of 10{sup {minus}6} m{sup 2} sec{sup {minus}1}. In the higher R{sub p} experiments, fingers are slower to evolve and do not interact as dynamically as in the lower R{sub p} systems. Our experiment with initial R{sub p} = 2.8 exhibited flux on the order of that expected for a similar diffusive system (i.e., 10{sup {minus}7} m{sup 2} sec{sup {minus}1}), although the structures were very different than the pattern of transport expected in a diffusing system. Mass flux decayed as t{sup 1/2} in two experiments each with initial R{sub p} = 2.4 and 2.8.
An experimental investigation was conducted to study double-diffusive finger convection in a Hele-Shaw cell by layering a sucrose solution over a more-dense sodium chloride (NaCl) solution. The solutal Rayleigh numbers were on the order of 60,000, based upon the height of the cell (25 cm), and the buoyancy ratio was 1.2. A full-field light transmission technique was used to measure a dye tracer dissolved in the NaCl solution. They analyze the concentration fields to yield the temporal evolution of length scales associated with the vertical and horizontal finger structure as well as the mass flux. These measures show a rapid progression through two early stages to a mature stage and finally a rundown period where mass flux decays rapidly. The data are useful for the development and evaluation of numerical simulators designed to model diffusion and convection of multiple components in porous media. The results are useful for correct formulation at both the process scale (the scale of the experiment) and effective scale (where the lab-scale processes are averaged-up to produce averaged parameters). A fundamental understanding of the fine-scale dynamics of double-diffusive finger convection is necessary in order to successfully parameterize large-scale systems.
The synthesis, structure and some properties of C{sub 2}H{sub 7}N{sub 4}O {center_dot} ZnPO{sub 4} (guanylurea zinc phosphate) are reported. The cationic template was prepared in situ by partial hydrolysis of the neutral 2-cyanoguanidine starting material. The resulting structure contains a new, unprotonated, zincophosphate layer topology as well as unusual N-H-O template-to-template hydrogen bonds which help to stabilize a ''double sandwich'' of templating cations between the inorganic sheets. Crystal data: C{sub 2}H{sub 7}N{sub 4}O {center_dot} ZnPO{sub 4}, M{sub r} = 229.44, monoclinic, P2{sub 1}/c, a = 13.6453 (9) {angstrom}, b = 5.0716 (3) {angstrom}, c = 10.6005 (7) {angstrom}, {beta} = 95.918 (2){sup 0}, V = 729.7 (1) {angstrom}{sup 3}, R(F) = 0.034, wR(F) = 0.034.
Laboratory experiments utilizing different near-infrared (NIR) sensitive imaging techniques for LADAR range gated imaging at eye-safe wavelengths are presented. An OPO/OPA configuration incorporating a nonlinear crystal for wavelength conversion of 1.56 micron probe or broadcast laser light to 807 nm light by utilizing a second pump laser at 532 nm for gating and gain, was evaluated for sensitivity, resolution, and general image quality. These data are presented with similar test results obtained from an image intensifier based upon a transferred electron (TE) photocathode with high quantum efficiency (QE) in the 1-2 micron range, with a P-20 phosphor output screen. Data presented include range-gated imaging performance in a cloud chamber with varying optical attenuation of laser reflectance images.
Research is presented on infrared (IR) and near infrared (NIR) sensitive sensor technologies for use in a high speed shuttered/intensified digital video camera system for range-gated imaging at ''eye-safe'' wavelengths in the region of 1.5 microns. The study is based upon nonlinear crystals used for second harmonic generation (SHG) in optical parametric oscillators (OPOS) for conversion of NIR and IR laser light to visible range light for detection with generic S-20 photocathodes. The intensifiers are ''stripline'' geometry 18-mm diameter microchannel plate intensifiers (MCPIIS), designed by Los Alamos National Laboratory and manufactured by Philips Photonics. The MCPIIS are designed for fast optical shattering with exposures in the 100-200 ps range, and are coupled to a fast readout CCD camera. Conversion efficiency and resolution for the wavelength conversion process are reported. Experimental set-ups for the wavelength shifting and the optical configurations for producing and transporting laser reflectance images are discussed.
A new way of providing calibration services is evolving which employs the Internet to expand present capabilities and make the calibration process more interactive. Sandia National Laboratories and the National Institute of Standards and Technology are collaborating to set up and demonstrate a remote calibration of multijunction calibrators using this Internet-based technique that is becoming known as e-calibration. This paper describes the measurement philosophy and the Internet resources that can provide real-time audio/video/data exchange, consultation and training, as well as web-accessible test procedures, software and calibration reports. The communication system utilizes commercial hardware and software that should be easy to integrate into most calibration laboratories.
Palmierite (K{sub 2}Pb(SO{sub 4}){sub 2}) has been prepared via a chemical synthesis method. Intensity differences were observed when X-ray powder data from the newly synthesized compound were compared to the published powder diffraction card (PDF) 29-1015 for Palmierite. Investigation of these differences indicated the possibility of preferred orientation and/or chemical inhomogeneity affecting intensities, particularly those of the basal (00{ell}) reflections. Annealing of the Palmierite was found to reduce the effects of preferred orientation. Electron microprobe analysis confirmed K:Pb:S as 2:1:2 for the annealed Palmierite powder. Subsequent least-squares refinement and Rietveld analysis of the annealed powder showed peak intensities very close to that of a calculated Palmierite pattern (based on single crystal data), yet substantially higher than many of the PDF 29-1015 published intensities. Further investigation of peak intensity variation via calculated patterns suggested that the intensity discrepancies between the annealed sample and those found in PDF 29-1015 were potentially due to chemical variation in the K{sub 2}Pb(SO{sub 4}){sub 2} composition. X-ray powder diffraction and crystal data for Palmierite are reported for the annealed sample. Palmierite is Trigonal/Hexagonal with unit cell parameters a = 5.497(1){angstrom}, c = 20.864(2) {angstrom}, space group R-3m (166), and Z = 3.
A semi-analytical solution is developed for one-dimensional steady infiltration in unsaturated fractured rock. The differential form of the mass conservation equation is integrated to yield an analytical expression relating elevation to a function of capillary pressure and relative permeability of the fracture and rock matrix. Constitutive relationships for unsaturated flow in this analysis are taken from van Genuchten [1980] and Mualem [1976], but alternative relations can also be implemented in the integral solution. Expressions are presented for the liquid saturations and pore velocities in the fracture, matrix, and effective continuum materials as a function of capillary pressure and elevation. Results of the analytical solution are applied to examples of infiltration in fractured rock consisting of both homogeneous and composite (layered) domains. The analytical results are also compared to numerical simulations to demonstrate the use of the analytical solution as a benchmarking tool to address computational issues such as grid refinement.
The Database of Environmental Parameters, Organizations, and Tools (DEPOT) has been developed by the Department of Energy (DOE) as a central warehouse for access to data essential for environmental risk assessment analyses. Initial efforts have concentrated on groundwater and vadose zone transport data and bioaccumulation factors. DEPOT seeks to provide a source of referenced data that, wherever possible, includes the level of uncertainty associated with these parameters. Based on the amount of data available for a particular parameter, uncertainty is expressed as a standard deviation or a distribution function. DEPOT also provides DOE site-specific performance assessment data, pathway-specific transport data, and links to environmental regulations, disposal site waste acceptance criteria, other environmental parameter databases, and environmental risk assessment models.
Monitoring of dielectric thin-film production in the microelectronics industry is generally accomplished by depositing a representative film on a monitor wafer and determining the film properties off line. One of the most important dielectric thin films in the manufacture of integrated circuits is borophosphosilicate glass (BPSG). The critical properties of BPSG thin films are the boron content, phosphorus content and film thickness. We have completed an experimental study that demonstrates that infrared emission spectroscopy coupled with multivariate analysis can be used to simultaneous y determine these properties directly from the spectra of product wafers, thus eliminating the need of producing monitor wafers. In addition, infrared emission data can be used to simultaneously determine the film temperature, which is an important film production parameter. The infrared data required to make these determinations can be collected on a time scale that is much faster than the film deposition time, hence infrared emission is an ideal candidate for an in-situ process monitor for dielectric thin-film production.
The elevated temperature creep properties of the 50Au-50Cu wt% and 47Au-50Cu-3Ni braze alloys have been evaluated over the temperature range 250-850 C. At elevated temperatures, i.e., 450-850 C, both alloys were tested in the annealed condition (2 hrs. 750 C/water quenched). The minimum strain rate properties over this temperature range are well fit by the Garofalo sinh equation. At lower temperatures (250 and 350 C), power law equations were found to characterize the data for both alloys. For samples held long periods of time at 375 C (96 hrs.) and slowly cooled to room temperature, an ordering reaction was observed. For the case of the 50Au-50Cu braze alloy, the stress necessary to reach the same, strain rate increased by about 15% above the baseline data. The limited data for ordered 47Au-50Cu-3Ni alloy reflected a,smaller strength increase. However, the sluggishness of this ordering reaction in both alloys does not appear to pose a problem for braze joints cooled at reasonable rates following brazing.
The structural changes in the heme macrocycle and substituents caused by binding of Ca{sup 2+} to the diheme cytochrome c peroxidase from Paracoccuspantotrophus were clarified by resonance Raman spectroscopy of the inactive filly oxidized form of the enzyme. The changes in the macrocycle vibrational modes are consistent with a Ca{sup 2+}-dependent increase in the out-of-plane distortion of the low-potential heme, the proposed peroxidatic heme. Most of the increase in out-of-plane distortion occurs when the high affinity site I is occupied, but a small further increase in distortion occurs when site II is also occupied by Ca{sup 2+}or Mg{sup 2+}. This increase in the heme distortion also explains the red shift in the Soret absorption band that occurs upon Ca{sup 2+} binding. Changes also occur in the low frequency substituent modes of the heme, indicating that a structural change in the covalently attached fingerprint pentapeptide of the LP heme occurs upon CM{sup 2+} binding to site I. These structural changes, possibly enhanced in the semi-reduced form of the enzyme, may lead to loss of the sixth ligand at the peroxidatic heme and activation of the enzyme.
The purpose of the program is to investigate the response of representative scale models of nuclear containment to pressure loading beyond the design basis accident and to compare analytical predictions to measured behavior. This objective is accomplished by conducting static, pneumatic overpressurization tests of scale models at ambient temperature. This research program consists of testing two scale models: a steel containment vessel (SCV) model (tested in 1996) and a prestressed concrete containment vessel (PCCV) model, which is the subject of this paper.