In this paper we present an analysis of a new configuration for achieving spin stabilized magnetic levitation. In the classical configuration, the rotor spins about a vertical axis; and the spin stabilizes the lateral instability of the top in the magnetic field. In this new configuration the rotor spins about a horizontal axis; and the spin stabilizes the axial instability of the top in the magnetic field.
ML is a multigrid preconditioning package intended to solve linear systems of equations Ax = b where A is a user supplied n x n sparse matrix, b is a user supplied vector of length n and x is a vector of length n to be computed. ML should be used on large sparse linear systems arising from partial differential equation (PDE) discretizations. While technically any linear system can be considered, ML should be used on linear systems that correspond to things that work well with multigrid methods (e.g. elliptic PDEs). ML can be used as a stand-alone package or to generate preconditioners for a traditional iterative solver package (e.g. Krylov methods). We have supplied support for working with the Aztec 2.1 and AztecOO iterative package [16]. However, other solvers can be used by supplying a few functions. This document describes one specific algebraic multigrid approach: smoothed aggregation. This approach is used within several specialized multigrid methods: one for the eddy current formulation for Maxwell's equations, and a multilevel and domain decomposition method for symmetric and nonsymmetric systems of equations (like elliptic equations, or compressible and incompressible fluid dynamics problems). Other methods exist within ML but are not described in this document. Examples are given illustrating the problem definition and exercising multigrid options.
As technical knowledge grows deeper, broader, and more interconnected, knowledge domains increasingly combine a number of sub-domains. More often than not, each of these sub-domains has its own community of specialists and forums for interaction. Hence, from a generalist's viewpoint, it is sometimes difficult to understand the relationships between the sub-domains within the larger domain; and, from a specialist's viewpoint, it may be difficult for those working in one sub-domain to keep abreast of knowledge gained in another sub-domain. These difficulties can be especially important in the initial stages of creating new projects aimed at adding knowledge either at the domain or sub-domain level. To circumvent these difficulties, one would ideally like to create a map of the knowledge domain--a map which would help clarify relationships between the various sub-domains, and a map which would help inform choices regarding investing in the production of knowledge either at the domain or sub-domain levels. In practice, creating such a map is non-trivial. First, relationships between knowledge subdomains are complex, and not likely to be easily simplified into a visualizable 2-or-few-dimensional map. Second, even if some of the relationships can be simplified, capturing them would require some degree of expert understanding of the knowledge domain, rendering impossible any fully automated method for creating the map. In this work, we accept these limitations, and within them, attempt to explore semi-automated methodologies for creating such a map. We chose as the knowledge domain for this case study 'displacement damage phenomena in Si junction devices'. This knowledge domain spans a particularly wide range of knowledge subdomains, and hence is a particularly challenging one.
Microfluidic systems are becoming increasingly complicated as the number of applications grows. The use of microfluidic systems for chemical and biological agent detection, for example, requires that a given sample be subjected to many process steps, which requires microvalves to control the position and transport of the sample. Each microfluidic application has its own specific valve requirements and this has precipitated the wide variety of valve designs reported in the literature. Each of these valve designs has its strengths and weaknesses. The strength of the valve design proposed here is its simplicity, which makes it easy to fabricate, easy to actuate, and easy to integrate with a microfluidic system. It can be applied to either gas phase or liquid phase systems. This novel design uses a secondary fluid to stop the flow of the primary fluid in the system. The secondary fluid must be chosen based on the type of flow that it must stop. A dielectric fluid must be used for a liquid phase flow driven by electroosmosis, and a liquid with a large surface tension should be used to stop a gas phase flow driven by a weak pressure differential. Experiments were carried out investigating certain critical functions of the design. These experiments verified that the secondary fluid can be reversibly moved between its 'valve opened' and 'valve closed' positions, where the secondary fluid remained as one contiguous piece during this transport process. The experiments also verified that when Fluorinert is used as the secondary fluid, the valve can break an electric circuit. It was found necessary to apply a hydrophobic coating to the microchannels to stop the primary fluid, an aqueous electrolyte, from wicking past the Fluorinert and short-circuiting the valve. A simple model was used to develop valve designs that could be closed using an electrokinetic pump, and re-opened by simply turning the pump off and allowing capillary forces to push the secondary fluid back into its stowed position.
Abstract not provided.
The goal of this study was to first establish the fitness for service of the carbon steel based oil coolers presently located at the Bryan Mound and West Hackberry sites, and second, to compare quantitatively the performance of two proposed corrosion mitigation strategies. To address these goals, a series of flow loops were constructed to simulate the conditions present within the oil coolers allowing the performance of each corrosion mitigation strategy, as well as the baseline performance of the existing systems, to be assessed. As prior experimentation had indicated that the corrosion and fouling was relatively uniform within the oil coolers, the hot and cold side of the system were simulated, representing the extremes of temperature observed within a typical oil cooler. Upon completion of the experiment, the depth of localized attack observed on carbon steel was such that perforation of the tube walls would likely result within a 180 day drawdown procedure at West Hackberry. Furthermore, considering the average rate of wall recession (from LPR measurements), combined with the extensive localized attack (pitting) which occurred in both environments, the tubing wall thickness remaining after 180 days would be less than that required to contain the operating pressures of the oil coolers for both sites. Finally, the inhibitor package, while it did reduce the measured corrosion rate in the case of the West Hackberry solutions, did not provide a sufficient reduction in the observed attack to justify its use.
Natural gas is a clean fuel that will be the most important domestic energy resource for the first half the 21st centtuy. Ensuring a stable supply is essential for our national energy security. The research we have undertaken will maximize the extractable volume of gas while minimizing the environmental impact of surface disturbances associated with drilling and production. This report describes a methodology for comprehensive evaluation and modeling of the total gas system within a basin focusing on problematic horizontal fluid flow variability. This has been accomplished through extensive use of geophysical, core (rock sample) and outcrop data to interpret and predict directional flow and production trends. Side benefits include reduced environmental impact of drilling due to reduced number of required wells for resource extraction. These results have been accomplished through a cooperative and integrated systems approach involving industry, government, academia and a multi-organizational team within Sandia National Laboratories. Industry has provided essential in-kind support to this project in the forms of extensive core data, production data, maps, seismic data, production analyses, engineering studies, plus equipment and staff for obtaining geophysical data. This approach provides innovative ideas and technologies to bring new resources to market and to reduce the overall environmental impact of drilling. More importantly, the products of this research are not be location specific but can be extended to other areas of gas production throughout the Rocky Mountain area. Thus this project is designed to solve problems associated with natural gas production at developing sites, or at old sites under redevelopment.
A novel method employing machine-based learning to identify messages related to other messages is described and evaluated. This technique may enable an analyst to identify and correlate a small number of related messages from a large sample of individual messages. The classic machine learning techniques of decision trees and naive Bayes classification are seeded with few (or no) messages of interest and 'learn' to identify other related messages. The performance of this approach and these specific learning techniques are evaluated and generalized.
Hydrogen has the potential to become an integral part of our energy transportation and heat and power sectors in the coming decades and offers a possible solution to many of the problems associated with a heavy reliance on oil and other fossil fuels. The Hydrogen Futures Simulation Model (H2Sim) was developed to provide a high level, internally consistent, strategic tool for evaluating the economic and environmental trade offs of alternative hydrogen production, storage, transport and end use options in the year 2020. Based on the model's default assumptions, estimated hydrogen production costs range from 0.68 $/kg for coal gasification to as high as 5.64 $/kg for centralized electrolysis using solar PV. Coal gasification remains the least cost option if carbon capture and sequestration costs ($0.16/kg) are added. This result is fairly robust; for example, assumed coal prices would have to more than triple or the assumed capital cost would have to increase by more than 2.5 times for natural gas reformation to become the cheaper option. Alternatively, assumed natural gas prices would have to fall below $2/MBtu to compete with coal gasification. The electrolysis results are highly sensitive to electricity costs, but electrolysis only becomes cost competitive with other options when electricity drops below 1 cent/kWhr. Delivered 2020 hydrogen costs are likely to be double the estimated production costs due to the inherent difficulties associated with storing, transporting, and dispensing hydrogen due to its low volumetric density. H2Sim estimates distribution costs ranging from 1.37 $/kg (low distance, low production) to 3.23 $/kg (long distance, high production volumes, carbon sequestration). Distributed hydrogen production options, such as on site natural gas, would avoid some of these costs. H2Sim compares the expected 2020 per mile driving costs (fuel, capital, maintenance, license, and registration) of current technology internal combustion engine (ICE) vehicles (0.55$/mile), hybrids (0.56 $/mile), and electric vehicles (0.82-0.84 $/mile) with 2020 fuel cell vehicles (FCVs) (0.64-0.66 $/mile), fuel cell vehicles with onboard gasoline reformation (FCVOB) (0.70 $/mile), and direct combustion hydrogen hybrid vehicles (H2Hybrid) (0.55-0.59 $/mile). The results suggests that while the H2Hybrid vehicle may be competitive with ICE vehicles, it will be difficult for the FCV to compete without significant increases in gasoline prices, reduced predicted vehicle costs, stringent carbon policies, or unless they can offer the consumer something existing vehicles can not, such as on demand power, lower emissions, or better performance.
Abstract not provided.
Specimens of poled 'chem-prep' PNZT ceramic from batch HF803 were tested under hydrostatic, uniaxial, and constant stress difference loading conditions at three temperatures of -55, 25, and 75 C and pressures up to 500 MPa. The objective of this experimental study was to obtain the electro-mechanical properties of the ceramic and the criteria of FE (Ferroelectric) to AFE (Antiferroelectric) phase transformations so that grain-scale modeling efforts can develop and test models and codes using realistic parameters. The poled ceramic undergoes anisotropic deformation during the transition from a FE to an AFE structure. The lateral strain measured parallel to the poling direction was typically 35 % greater than the strain measured perpendicular to the poling direction. The rates of increase in the phase transformation pressures per temperature changes were practically identical for both unpoled and poled PNZT HF803 specimens. We observed that the retarding effect of temperature on the kinetics of phase transformation appears to be analogous to the effect of shear stress. We also observed that the FE-to-AFE phase transformation occurs in poled ceramic when the normal compressive stress, acting perpendicular to a crystallographic plane about the polar axis, equals the hydrostatic pressure at which the transformation otherwise takes place.
As part of the Arsenic Water Technology Partnership program, Sandia National Laboratories will carry out field demonstration testing of innovative technologies that have the potential to substantially reduce the costs associated with arsenic removal from drinking water. The scope for this work includes: (1) selection of sites for pilot demonstrations, (2) identification of candidate technologies through Vendor Forums, proof-of-principle bench-scale studies managed by the American Water Works Association Research Foundation (AwwaRF) or the WERC design contest, and (3) pilot-scale studies involving side-by-side tests of innovative technologies. The goal of site selection is identification of a suite of sites that exhibit a sufficiently wide range of groundwater chemistries to allow examination of treatment processes and systems under conditions that are relevant to different geochemical settings throughout the country. A number of candidate sites have been identified through reviews of groundwater quality databases, conference proceedings and discussions with state and local officials. These include sites in New Mexico, Arizona, Colorado, Oklahoma, Illinois, Michigan, Florida, Massachusetts and New Hampshire. In New Mexico, discussions have been held with water utility board staffs in Chama, Jemez Pueblo, Placitas, Socorro and several communities near Las Cruces to determine the suitability of those communities for pilot studies. The initial pilot studies will be carried at Socorro and Jemez Pueblo; other communities will be included as the program progresses. The proposed pilot test at a hot spring water source near Socorro will provide an opportunity to test treatment technologies at relatively high temperatures. If approved by the Tribal Government, the proposed pilot at the Jemez Pueblo would provide an opportunity to test technologies that will remove arsenic in the presence of relatively high concentrations of iron and manganese while leaving the beneficial levels of fluoride unchanged. Candidate technologies for the pilot tests are being reviewed by technical evaluation teams. The initial reviews will consider as many potential technologies and screen out unsuitable ones by considering data from past performance testing, expected costs, complexity of operation and maturity of the technology. The pilot test configurations will depend on the site-specific conditions such as access, power availability, waste disposal options and availability of permanent structures to house the test. Most of the treatment technologies that will be evaluated can be separated into two broad categories: (1) sorption processes that use fixed bed adsorbents and (2) membrane processes. The latter include processes that involve formation of a floc or precipitate that contains the arsenic in a reactor followed by separation of the solids from the water by filtration. Several innovations that could lead to lower treatment costs have been proposed for adsorptive media systems. These include: (1) higher capacity and selectivity using mixed oxides composed of iron and other transition metals, titanium and zirconium based oxides, or mixed resin-metal oxides composite media, (2) improved durability of virgin media and greater chemical stability of the spent media, and (3) use of inexpensive natural or recycled materials with a coating that has a high affinity for arsenic. Improvements to filtration-based treatment systems include: (1) enhanced coagulation with iron compounds or polyelectrolytes and (2) improved filtration with nanocomposite materials. In the pilot tests, the innovative technologies will be evaluated in terms of: (1) their ability to reduce arsenic to levels below the EPA Maximum Contaminant Level (MCL) of 10 ppb, (2) site-specific adsorptive capacity, robustness of performance with respect to likely changes in water quality parameters including pH, TDS, foulants such as Fe, Mn, silica, and organics, effect of competing ions such as other metals and radionuclides, and potentially deleterious effects on the water system such as pipe corrosion from low pH levels, fluoride removal, and generation of disinfection by-products. The new arsenic MCL will result in modification of many rural water systems that otherwise would not require treatment. Opportunities for improvement of water quality in systems that currently do not comply with other standards would be an added benefit from the new arsenic MCL that has both economic and public health value.
Understanding the dynamics of the membrane protein rhodopsin will have broad implications for other membrane proteins and cellular signaling processes. Rhodopsin (Rho) is a light activated G-protein coupled receptor (GPCR). When activated by ligands, GPCRs bind and activate G-proteins residing within the cell and begin a signaling cascade that results in the cell's response to external stimuli. More than 50% of all current drugs are targeted toward G-proteins. Rho is the prototypical member of the class A GPCR superfamily. Understanding the activation of Rho and its interaction with its Gprotein can therefore lead to a wider understanding of the mechanisms of GPCR activation and G-protein activation. Understanding the dark to light transition of Rho is fully analogous to the general ligand binding and activation problem for GPCRs. This transition is dependent on the lipid environment. The effect of lipids on membrane protein activity in general has had little attention, but evidence is beginning to show a significant role for lipids in membrane protein activity. Using the LAMMPS program and simulation methods benchmarked under the IBIG program, we perform a variety of allatom molecular dynamics simulations of membrane proteins.
Abstract not provided.
Abstract not provided.
Abstract not provided.
To investigate the performance of artificial frozen soil materials with a fused interface, split tension (or 'Brazilian') tests and unconfined uniaxial compression tests were carried out in a low temperature environmental chamber. Intact and fused specimens were fabricated from four different soil mixtures (962: clay-rich soil with bentonite; DNA1: clay-poor soil; DNA2: clay-poor soil with vermiculite; and DNA3: clay-poor soil with perlite). Based on the 'Brazilian' test results and density measurements, the DNA3 mixture was selected to closely represent the mechanical properties of the Alaskan frozen soil. The healed-interface by the same soil layer sandwiched between two blocks of the same material yielded the highest 'Brazilian' tensile strength of the interface. Based on unconfined uniaxial compression tests, the frictional strength of the fused DNA3 specimens with the same soil appears to exceed the shear strength of the intact specimen.
Laser-induced incandescence is used to measure time-resolved diesel particulate emissions for two lean NOx trap regeneration strategies that utilize intake throttling and in-cylinder fuel enrichment. The results show that when the main injection event is increased in duration and delayed 13 crank-angle degrees, particulate emissions are very high. For a repetitive pattern of 3 seconds of rich regeneration followed by 27 seconds of NOx-trap loading, we find a monotonic increase in particulate emissions during the loading intervals that approaches twice the initial baseline particulate level after 1000 seconds. In contrast, particulate emissions during the re-generation intervals are constant throughout the test sequence. For regeneration using an additional late injection event (post-injection), particulate emissions are about twice the baseline level for the first regeneration interval, but then decay with an exponential-like behavior over the repetitive test sequence, eventually reaching a level that is comparable to the baseline. In contrast, particulate emissions between regenerations decrease slowly throughout the test sequence, reaching a level 12 percent below the starting baseline value.
Proposed for publication in a journal article to be determined.
An Al{sub 85}Ni{sub 10}La{sub 5} amorphous alloy, produced via gas atomization, was selected to study the mechanisms of nanocrystallization induced by thermal exposure. High resolution transmission electron microscopy results indicated the presence of quenched-in Al nuclei in the amorphous matrix of the atomized powder. However, a eutectic-like reaction, which involved the formation of the Al, Al{sub 11}La{sub 3}, and Al{sub 3}Ni phases, was recorded in the first crystallization event (263 C) during differential scanning calorimetry continuous heating. Isothermal annealing experiments conducted below 263 C revealed that the formation of single fcc-Al phase occurred at 235 C. At higher temperatures, growth of the Al crystals occurred with formation of intermetallic phases, leading to a eutectic-like transformation behavior at 263 C. During the first crystallization stage, nanocrystals were developed in the size range of 5 - 30 nm. During the second crystallization event (283 C), a bimodal size distribution of nanocrystals was formed with the smaller size in the range of around 10 - 30 nm and the larger size around 100 nm. The influence of pre-existing quenched-in Al nuclei on the microstructural evolution in the amorphous Al{sub 85}Ni{sub 10}La{sub 5} alloy is discussed and the effect of the microstructural evolution on the hardening behavior is described in detail.
Abstract not provided.
Publication in
Abstract not provided.
Abstract not provided.
Abstract not provided.
Abstract not provided.
Center for Turbulence Research Proceedings of the Summer Program 2004
Abstract not provided.
Fires pose the dominant risk to the safety and security of nuclear weapons, nuclear transport containers, and DOE and DoD facilities. The thermal hazard from these fires primarily results from radiant emission from high-temperature flame soot. Therefore, it is necessary to understand the local transport and chemical phenomena that determine the distributions of soot concentration, optical properties, and temperature in order to develop and validate constitutive models for large-scale, high-fidelity fire simulations. This report summarizes the findings of a Laboratory Directed Research and Development (LDRD) project devoted to obtaining the critical experimental information needed to develop such constitutive models. A combination of laser diagnostics and extractive measurement techniques have been employed in both steady and pulsed laminar diffusion flames of methane, ethylene, and JP-8 surrogate burning in air. For methane and ethylene, both slot and coannular flame geometries were investigated, as well as normal and inverse diffusion flame geometries. For the JP-8 surrogate, coannular normal diffusion flames were investigated. Soot concentrations, polycyclic aromatic hydrocarbon (PAH) laser-induced fluorescence (LIF) signals, hydroxyl radical (OH) LIF, acetylene and water vapor concentrations, soot zone temperatures, and the velocity field were all successfully measured in both steady and unsteady versions of these various flames. In addition, measurements were made of the soot microstructure, soot dimensionless extinction coefficient (&), and the local radiant heat flux. Taken together, these measurements comprise a unique, extensive database for future development and validation of models of soot formation, transport, and radiation.
Abstract not provided.
Abstract not provided.
Abstract not provided.
Abstract not provided.
Abstract not provided.
Abstract not provided.
LIGA is an acronym for the German terms Lithographie, Galvanoformung, Abformung, which describe a microfabrication process for high aspect ratio, structural parts based on electrodeposition of a metal into a poly-methyl-methacrylate (PMMA) mold. LIGA produced parts have very high dimensional tolerances (on the order of a micron) and can vary in size from microns to centimeters. These properties make LIGA parts ideal for incorporation into MEMS devices or for other applications where strict tolerances must be met; however, functionality of the parts can only be maintained if they remain dimensionally stable throughout their lifetime. It follows that any form of corrosion attack (e.g., uniform dissolution, localized pitting, environmental cracking, etc.) cannot be tolerated. This presentation focuses on the pitting behavior of Ni electrodeposits, specifically addressing the influence of the following: grain structure, alloy composition, impurities, plating conditions, post plating processing (including chemical and thermal treatment), galvanic interactions and environment (aqueous vs. atmospheric). A small subset of these results is summarized. A typical LIGA part is shown in Figure 1. Due to the small size scale, electrochemical testing was performed using a capillary based test system. Although very small test areas can be probed with this system (e.g., Figure 2), typically capillaries on the order of 80 to 90 ?m's were used in the testing. All LIGA parts tested in the as-received condition had better pitting resistance than the high purity wrought Ni material used as a control. In the case of LIGA-Ni and LIGA-Ni-Mn, no detrimental effects were observed due to aging at 700C. Ni-S (approximately 500 ppm S), showed good as-received pitting behavior but decreased pitting resistance with thermal aging. Aged Ni-S showed dramatic increases in grain size (from single {micro}m's to 100's of {micro}m's), and significant segregation of S to the boundaries. The capillary test cell was used to measure pitting potentials at the boundaries and within grains (Figure 3) with the results clearly showing the lowered pit resistance being due to the S-rich boundaries. It is believed that the process used to release the LIGA parts from the Cu substrate acts as a pickling agent for the LIGA parts, resulting in removal of surface impurities and detrimental alloying additions. EIS data from freshly polished samples exposed to the release bath support this hypothesis; RP values for all LIGA materials and for wrought Ni, continuously increase during exposure. Mechanical polishing of LIGA parts prior to electrochemical testing consistently resulted in lowering the pitting potentials to a range bounded by Ni 201 and high purity Ni. The as-received vs. polished behavior also effects the galvanic interactions with noble metals. When as-produced material is coupled to Au, initially the LIGA material acts as the cathode, though eventually the behavior switches such that the LIGA becomes the anode. Overall, the LIGA produced Ni and Ni alloys examined in this work demonstrated pitting behavior similar to wrought Ni, only showing reduced resistance when specific metallurgical and environmental conditions were met.
A series of experiments was performed to better characterize the boundary conditions from an inconel heat source ('shroud') painted with Pyromark black paint. Quantifying uncertainties in this type of experimental setup is crucial to providing information for comparisons with code predictions. The characterization of this boundary condition has applications in many scenarios related to fire simulation experiments performed at Sandia National Laboratories Radiant Heat Facility (RHF). Four phases of experiments were performed. Phase 1 results showed that a nominal 1000 C shroud temperature is repeatable to about 2 C. Repeatability of temperatures at individual points on the shroud show that temperatures do not vary more than 10 C from experiment to experiment. This variation results in a 6% difference in heat flux to a target 4 inches away. IR camera images showed the shroud was not at a uniform temperature, although the control temperature was constant to about {+-}2 C during a test. These images showed that a circular shaped, flat shroud with its edges supported by an insulated plate has a temperature distribution with higher temperatures at the edges and lower temperatures in the center. Differences between the center and edge temperatures were up to 75 C. Phase 3 results showed that thermocouple (TC) bias errors are affected by coupling with the surrounding environment. The magnitude of TC error depends on the environment facing the TC. Phase 4 results were used to estimate correction factors for specific applications (40 and 63-mil diameter, ungrounded junction, mineral insulated, metal-sheathed TCs facing a cold surface). Correction factors of about 3.0-4.5% are recommended for 40 mil diameter TCs and 5.5-7.0% for 63 mil diameter TCs. When mounted on the cold side of the shroud, TCs read lower than the 'true' shroud temperature, and the TC reads high when on the hot side. An alternate method uses the average of a cold side and hot side TC of the same size to estimate the true shroud temperature. Phase 2 results compared IR camera measurements with TC measurements and measured values of Pyromark emissivity. Agreement was within measured uncertainties of the Pyromark paint emissivity and IR camera temperatures.
Mathematical models are developed and used to study the properties of complex systems and/or modify these systems to satisfy some performance requirements in just about every area of applied science and engineering. A particular reason for developing a model, e.g., performance assessment or design, is referred to as the model use. Our objective is the development of a methodology for selecting a model that is sufficiently accurate for an intended use. Information on the system being modeled is, in general, incomplete, so that there may be two or more models consistent with the available information. The collection of these models is called the class of candidate models. Methods are developed for selecting the optimal member from a class of candidate models for the system. The optimal model depends on the available information, the selected class of candidate models, and the model use. Classical methods for model selection, including the method of maximum likelihood and Bayesian methods, as well as a method employing a decision-theoretic approach, are formulated to select the optimal model for numerous applications. There is no requirement that the candidate models be random. Classical methods for model selection ignore model use and require data to be available. Examples are used to show that these methods can be unreliable when data is limited. The decision-theoretic approach to model selection does not have these limitations, and model use is included through an appropriate utility function. This is especially important when modeling high risk systems, where the consequences of using an inappropriate model for the system can be disastrous. The decision-theoretic method for model selection is developed and applied for a series of complex and diverse applications. These include the selection of the: (1) optimal order of the polynomial chaos approximation for non-Gaussian random variables and stationary stochastic processes, (2) optimal pressure load model to be applied to a spacecraft during atmospheric re-entry, and (3) optimal design of a distributed sensor network for the purpose of vehicle tracking and identification.
Proceedings of the National Academy of Science
Abstract not provided.
Abstract not provided.
Abstract not provided.
Abstract not provided.
The irradiation of thin insulating films by high-energy ions (374 MeV Au{sup +25} or 241 MeV I{sup +19}) was used to attempt to form nanometer-size pores through the films spontaneously. Such ions deposit a large amount of energy into the target materials ({approx}20 keV/nm), which significantly disrupts their atomic lattice and sputters material from the surfaces, and might produce nanopores for appropriate ion-material combinations. Transmission electron microscopy was used to examine the resulting ion tracks. Tracks were found in the crystalline oxides quartz, sapphire, and mica. Sapphire and mica showed ion tracks that are likely amorphous and exhibit pits 5 nm in diameter on the surface at the ion entrance and exit points. This suggests that nanopores might form in mica if the film thickness is less than {approx}10 nm. Tracks in quartz showed strain in the matrix around them. Tracks were not found in the amorphous thin films examined: 20 nm-SiN{sub x}, deposited SiOx, fused quartz (amorphous SiO{sub 2}), formvar and 3 nm-C. Other promising materials for nanopore formation were identified, including thin Au and SnO{sub 2} layers.
Abstract not provided.
Lead Free Magazine
Abstract not provided.
This report summarizes the results obtained from a Laboratory Directed Research & Development (LDRD) project entitled 'Investigation of Potential Applications of Self-Assembled Nanostructured Materials in Nuclear Waste Management'. The objectives of this project are to (1) provide a mechanistic understanding of the control of nanometer-scale structures on the ion sorption capability of materials and (2) develop appropriate engineering approaches to improving material properties based on such an understanding.
A radioactive sealed source is any radioactive material that is encased in a capsule designed to prevent leakage or escape of the radioactive material. Radioactive sealed sources are used for a wide variety of applications at hospitals, in manufacturing and research. Typical uses are in portable gauges to measure soil compaction and moisture or to determine physical properties of rocks units in boreholes (well logging). Hospitals and clinics use radioactive sealed sources for teletherapy and brachytherapy. Oil exploration and medicine are the largest users. Accidental mismanagement of radioactive sealed sources each year results in a large number of people receiving very high or even fatal does of ionizing radiation. Deliberate mismanagement is a growing international concern. Sealed sources must be managed and disposed effectively in order to protect human health and the environment. Effective national safety and management infrastructures are prerequisites for efficient and safe transportation, treatment, storage, and disposal. The Integrated Management Program for Radioactive Sealed Sources in Egypt (IMPRSS) is a cooperative development agreement between the Egyptian Atomic Energy Authority (EAEA), Egyptian Ministry of Health (MOH), Sandia National Laboratories (SNL), the University of New Mexico (UNM), and Agriculture Cooperative Development International (ACDI/VOCA). The EAEA, teaming with SNL, is conducting a Preliminary Safety Assessment (PSA) of an intermediate-depth borehole disposal in thick arid alluvium in Egypt based on experience with the U.S. Greater Confinement Disposal (GCD). Goldsim has been selected for the preliminary disposal system assessment for the Egyptian GCD Study. The results of the PSA will then be used to decide if Egypt desires to implement such a disposal system.
We have studied the feasibility of an innovative device to sample 1ns low-power single current transients with a time resolution better than 10 ps. The new concept explored here is to close photoconductive semiconductor switches (PCSS) with a Laser for a period of 10 ps. The PCSSs are in a series along a Transmission Line (TL). The transient propagates along the TL allowing one to carry out a spatially resolved sampling of charge at a fixed time instead of the usual timesampling of the current. The fabrication of such a digitizer was proven to be feasible but very difficult.
Proposed for publication in Computer Methods in Applied Mechanics and Engineering Journal.
This paper presents solution verification studies applicable to a class of problems involving wave propagation, frictional contact, geometrical complexity, and localized incompressibility. The studies are in support of a validation exercise of a phenomenological screw failure model. The numerical simulations are performed using a fully explicit transient dynamics finite element code, employing both standard four-node tetrahedral and eight-node mean quadrature hexahedral elements. It is demonstrated that verifying the accuracy of the simulation involves not only consideration of the mesh discretization error, but also the effect of the hourglass control and the contact enforcement. In particular, the proper amount of hourglass control and the behavior of the contact search and enforcement algorithms depend greatly on the mesh resolution. We carry out the solution verification exercise using mesh refinement studies and describe our systematic approach to handling the complicating issues. It is shown that hourglassing and contact must both be carefully monitored as the mesh is refined, and it is often necessary to make adjustments to the hourglass and contact user input parameters to accommodate finer meshes. We introduce in this paper the hourglass energy, which is used as an 'error indicator' for the hourglass control. If the hourglass energy does not tend to zero with mesh refinement, then an hourglass control parameter is changed and the calculation is repeated.
Abstract not provided.
We describe a new mode of encryption with inexpensive authentication, which uses information from the internal state of the cipher to provide the authentication. Our algorithms have a number of benefits: (1) the encryption has properties similar to CBC mode, yet the encipherment and authentication can be parallelized and/or pipelined, (2) the authentication overhead is minimal, and (3) the authentication process remains resistant against some IV reuse. We offer a Manticore class of authenticated encryption algorithms based on cryptographic hash functions, which support variable block sizes up to twice the hash output length and variable key lengths. A proof of security is presented for the MTC4 and Pepper algorithms. We then generalize the construction to create the Cipher-State (CS) mode of encryption that uses the internal state of any round-based block cipher as an authenticator. We provide hardware and software performance estimates for all of our constructions and give a concrete example of the CS mode of encryption that uses AES as the encryption primitive and adds a small speed overhead (10-15%) compared to AES alone.