Publications

We have obtained dual-longitudinal-mode operation of a Q-switched Nd:YAG laser by simultaneous injection-seeding at two frequencies to produce pulses with modulation frequency discretely tunable from 185 MHz to greater than 17 GHz.

This report highlights the following topics: Photon Correlation Spectroscopy--a new application in jet fuel analysis, Testing news in brief; Solar test facility supports space station research; Shock isolation technique developed for piezoresistive accelerometer; High-speed photography captures Distant Image measurements; and, Radiation effects test revised for CMOS electronics.

The intense radiation fields generated with useful uniformity over large volumes, using the novel compound-lens diode on Hermes III, are characterized. The measurements show that by changing the diode parameters, the peak dose, useful area, and useful volume of irradiation can be varied from ~100 krad(Si), ~600 cm2, and ~20×103 cm3 to 20 krad(Si), ~3400 cm2, and ~200×103 cm3, in a 19±2 ns radiation pulse. This versatility enables radiation fields to be tailored to a specified exposure requirement, significantly enhancing the capability of Hermes III to test radiation effects in systems. © 1992 IEEE

A monolithic dose-rate nuclear event detector (NED) has been evaluated as a function of radiation pulse width. The dose-rate trip level of the NED was evaluated in "near" minimum and maximum sensitivity configurations for pulse widths from 20 to 250 ns and at dose rates from 106 to 109 rads(Si)/s. The trip level varied up to a factor of ∼16 with pulse width. At each pulse width the trip level can be varied intentionally by adding external resistors. Neutron irradiations caused an increase in the trip level, while electron irradiations, up to a total-dose of 50 krads(Si), had no measurable effect. This adjustable dose-rate-level detector should prove valuable to designers of radiation-hardened systems.

Particulate contamination during IC fabrication is generally acknowledged as a major contributor to yield loss. In particular, plasma processes have the potential for generating copious quantities of process induced particulates. Ideally, in order to effectively control process generated particulate contamination, a fundamental understanding of the particulate generation and transport is essential. Although a considerable amount of effort has been expended to study particles in laboratory apparatus, only a limited amount of work has been performed in production line equipment with production processes. In these experiments, a Drytek Quad Model 480 single wafer etcher was used to etch blanket thermal SiO{sub 2} films on 150 mm substrates in fluorocarbon discharges. The effects of rf power, reactor pressure, and feed gas composition on particle production rates were evaluated. Particles were measured using an HYT downstream particle flux monitor. Surface particle deposition was measured using a Tencor Surfscan 4500, as well as advanced ex situ techniques. Particle morphology and composition were also determined ex situ. Response surface methodology was utilized to determine the process conditions under which particle generation was most pronounced. The use of in situ and ex situ techniques has provided some insight into the mechanisms involved for particle generation and particle dynamics within the plasma during oxide etching.

The conclusions of the vulnerability test on VOPAN (verification of Operator's Analysis) as conducted at Safeguards Analytical Laboratory (ASA) at Seibersdorf, Austria in October 1990 and documented in STR-266, indicate that whenever samples are taken for safeguards purposes extreme care must be taken to ensure that they have not been interfered with during the sample taking, transportation, storage or sample preparation process.'' Indeed there exist a number of possibilities to alter the content of a safeguards sample vial from the moment of sampling up to the arrival of the treated (or untreated) sample at SAL. The time lapse between these two events can range from a few days up to months. The sample history over this period can be subdivided into three main sub-periods: (1) the period from when the sampling activities are commenced up to the treatment in the operator's laboratory, (2) during treatment of samples in the operator's laboratory, and finally, (3) the period between that treatment and the arrival of the sample at SAL. A combined effort between the Agency and the United States Support Program to the Agency (POTAS) has resulted in two active tasks and one proposed task to investigate improving the maintenance of continuity of knowledge on safeguards samples during the entire period of their existence. This paper describes the use of the Sample Vial Secure Container (SVSC), of the Authenticated Secure Container System (ASCS), and of the Secure Container for Storage and Transportation of samples (SCST) to guarantee that a representative portion of the solution sample will be received at SAL.

A control algorithm is proposed for a molten-salt solar central receiver in a cylindrical configuration. The algorithm simultaneously regulates the receiver outlet temperature and limits thermal-fatigue damage of the receiver tubes to acceptable levels. The algorithm is similar to one that was successfully tested for a receiver in a cavity configuration at the Central Receiver Test Facility in 1988. Due to the differences in the way solar flux is introduced on the receivers during cloud-induced transients, the cylindrical receiver will be somewhat more difficult to control than the cavity receiver. However, simulations of a proposed cylindrical receiver at the Solar Two power plant have indicated that automatic control during severe cloud transients is feasible. This paper also provides important insights regarding receiver design and lifetime as well as a strategy for reducing the power consumed by the molten-salt pumps.

This paper describes experiments on the wettability of tin on oxygen free, high conductivity (OFHC) copper using a ″point source″ ultrasonic horn. Ultrasonics are used on such metals as aluminum or stainless steel which are difficult to wet without the use of very strong corrosives. These experiments explore the behavior of acoustic energy transmission in the horn-solder-substrate systems indicated by the solder film generated and explore the use of ultrasonics in actual electronic systems component fabrication and assembly processes.

An evaluation of substitutes for tin-lead alloy solders is discribed. The first part of the evaluation studies the wettability of tin-based, lead free solders. The second part evaluates the solderability. The solders evaluated were commercially available.

This paper presents the results of a set of structural analyses performed to investigate the effects of internal gas generation on the extension of pre-existing fractures around disposal rooms at the Waste Isolation Pilot Plant. The response of a room and its contents is computed for this scenario to establish the condition of the room at any point in time. The development of the capability to perform these analyses represents an additional step in the development of an overall model for the disposal room.

Acid vapors have been used to fluxlessly reduce metal oxides and enhance wetting of solder on metallizations. Dilute solutions of hydrogen, acetic acid and formic acid in an inert carrier gas of nitrogen or argon were used with the sessile drop technique for 60Sn-40Pb solder on Cu and Au/Ni metallizations. The time to reduce metal oxides and degree of wetting as a function of acid vapor concentration were characterized. Acetic and formic acids reduce the surface metal oxides sufficiently to form metallurgically sound solder joints. Hydrogen did not reduce oxides rapidly enough at 220°C to be suitable for soldering applications. The optimum conditions for oxide reduction with formic acid was with an acid vapor concentration in nitrogen carrier gas of 4% for Cu metallizations and 1.6% on Au/Ni. The acetic acid vapor concentration, also in nitrogen, was optimized at 1.5% for both metallizations. Above a vapor concentration of 1.5%, the acetic acid combined with the bare metal to form acetates which increased the wetting time. These results indicate that acid vapor fluxless soldering is a viable alternative to traditional flux soldering.

The measurement of surface pressures on a body which is submerged in flowing water involves several problems which are not encountered when the test medium is air. Many of these problems exist even if the water velocity is low, and become more severe at higher velocitics (45-65 ft/sec) where the surface pressure may be low enough for cavitation to occur. Problem areas which are discussed include:hydrostatic pressure, surface tension, orifice errors, thermal effects on surface-mounted transducers, electrical fields, two-phase phenomena and air content.

Deconing controllers are developed for a spinning spacecraft, where the control mechanism is that of axial or radial moving masses that are used to produce intentional, transient principal axis misalignments. A single mass axial controller is used to motivate the concept, and then axial and radial dual mass controllers are described. The two mass problem is of particular interest since spacecraft imbalances can be simultaneously removed with the same control logic. Each controller is tested via simulation for its ability to eliminate existing coning motion for a range of spin rates. Both controllers are developed via a linear-quadratic-regulator synthesis procedure, which is motivated by their multi-input/multi-output nature. The dynamic coupling in the radial two mass control problem introduces some particularly interesting design complications.

Many complex physical processes are modeled by coupled systems of partial differential equations (PDEs). Often, the numerical approximation of these PDEs requires the solution of large sparse nonsymmetric systems of equations. In this paper we compare the parallel performance of a number of preconditioned Krylov subspace methods on a large-scale MIMD machine. These methods are among the most robust and efficient iterative algorithms for the solution of large sparse linear systems. They are easy to implement on various architectures and work well on a wide variety of important problems. In this comparison we focus on the parallel issues associated with both local preconditioners (those that combine information from the entire domain). The various preconditioners are applied to a variety of PDE problems within the GMRES, CCGS, BiCGSTAB, and QMRCGS methods. Conclusions are drawn on the effectiveness of the different schemes based on results obtained from a 1024 processor a nCUBE 2 hypercube.

A two-stage self-organizing neural network architecture has been applied to object recognition in Synthetic Aperture Radar imagery. The first stage performs feature extraction and implements a two-layer Neocognitron. The resulting feature vectors are presented to the second stage, an ART 2-A classifier network, which clusters the features into multiple target categories. Training is performed off-line in two steps. First, the Neocognitron self-organizes in response to repeated presentations of an object to recognize. During this training process, discovered features and the mechanisms for their extraction are captured in the excitatory weight patterns. In the second step, Neocognitron learning is inhibited and the ART 2-A classifier forms categories in response to the feature vectors generated by additional presentations of the object to recognize. Finally, all training is inhibited and the system tested against a variety of objects and background clutter. In this paper we report the results of our initial experiments. The architecture recognizes a simulated tank vehicle at arbitrary azimuthal orientations at a single depression angle while rejecting clutter and other object returns. The neural architecture has achieved excellent classification performance using 20 clusters.

This paper presents results of a set of numerical experiments performed bo benchmark the Cell-Centered Implicit Continuous-fluid Eulerian (CCICE), and to determine their limitations as flow solvers for water entry and water exit simulations.

This paper will include a brief overview of the components of the QUICKSILVER suite and its current modeling capabilities. As time permits, results from sample applications will be shown, including time animations of simulation results.

Technologies that use carbon and mixed metal oxides as the electrode material have been pursued for the purpose of producing high-reliability double-layer capacitors (DLCs). The author demonstrates their environmental stability in temperature, shock, vibration, and linear acceleration. She reviews the available test data for both types of DLCs under these stress conditions. This study suggests that mixed metal oxides and carbon-based double-layer capacitors can survive robust environments if packaged properly, and that temperature decreases performance of double-layer capacitors.

We describe a simple engineering model applicable to stand-off “Whipple bumper” shields, which are used to protect space-based assets from impacts by orbital debris particles. The model provides a framework for analyzing: 1) the parameter limits governing the penetration and breakup or decomposition of the hypervelocity debris particle; 2) the behavior of the induced debris cloud, including its velocity and divergence; and 3) the design and optimization of the stand-off shield for a specific threat and level of protection required. The model is normalized to actual stand-off debris shield experiments and multi-dimensional numerical simulations at impact velocities of ~10 km/s. The subsequent analysis of a current space station shield design suggests that: 1) for acceptable levels of protection, stand-off shields can be significantly thinner than previously thought; and 2) with the proper balance between shield thickness and stand-off distance, the total shield mass can be reduced substantially.

A series of experiments has been performed on the Sandia Hypervelocity Launcher to determine the performance limits of conventional Whipple shields against representative 0.8 g aluminum orbital debris plate-like fragments with velocities of 7 and 10 km/s. Supporting diagnostics include flash X-rays, high speed photography and transient digitizers for timing correlation. Two Whipple shield designs were tested with either a 0.030 cm or a 0.127 cm thick front sheet and a 0.407 cm thick backsheet separated by 30.5 cm. These two designs bracket the ballistic penetration limit curve for protection against these debris simulants for 7 km/s impacts.

In this paper we take a new look at the tomographic formulation of spotlight mode synthetic aperture radar (SAR), so as to include the case of targets having three-dimensional structure. This bridges the work of David C. Munson and his colleagues, who first described SAR in terms of two-dimensional tomography, with Jack Walker`s original derivation of spotlight mode SAR imaging via Doppler analysis. The main result is to demonstrate that the demodulated radar return data from a spotlight mode collection represent a certain set of samples of the three-dimensional Fourier transform of the target reflectivity function, and to do so using tomographic principles instead of traditional Doppler arguments. We then show that the tomographic approach is useful in interpreting the two-dimensional SAR image of a three-dimensional scene. In particular, the well-known SAR imaging phenomenon commonly referred to as layover is easily explained in terms of tomographic projection. 4 refs.

Short communication.

The Sandia Airborne Computer (SANDAC) is a small, modular, high performance, multi-processor computer originally designed for aerospace applications. It can use a combination of Motorola 68020 and 68040 based processor modules along with AT&T DSP32C based signal processing modules. The system is designed to use up to 15 processors in almost any combination and a complete system can include up to 20 modules. Depending on the mix of processors, total computational throughput can range from 2.5 to greater than 225 million instructions per second (MIPS). The system is designed so that processors can access all resources in the machine and the inter-processor communication details are completely transparent to the software. In addition to processors, the system includes input/output, memory, and special function modules. Because of its ease of use, small size, durability, and configuration flexibility, SANDAC has been used on applications ranging from missile navigation, guidance and control systems to medical imaging systems. © 1992.

The unit cell shape of thick frequency selective surfaces, or dichroic plate, is dependent on its frequency requirements. One aperture shape may be chosen to give wider bandwidths, and another chosen for sharper frequency roll-off. This is analogous to circuits where the need for differing frequency response determines the circuit topology. Acting as spatial frequency filters, dichroics are a critical component in supporting the Deep Space Network (DSN) for spacecraft command a control up links as well as spacecraft down links. Currently these dichroic plates separate S-band at 2.0--232 GHz from X-band at 8.4--8.45 GHz. But new spacecraft communication requirements are also calling for an up link frequency at 7.165 GHz. In addition future spacecraft such as Craft/Casssini will require dichroics effectively separating K{sub a}-band frequencies in the 31--35 GHz range. The requirements for these surfaces are low transmission loss of < 0.1 dB at high power levels. Also is important to maintain a minimal relative phase shift between polarizations for circular polarization transmission. More current work has shown the successful demonstration of design techniques for straight, rectangular apertures at an incident angle of 30{degrees}. The plates are air-filled due to power dissipation and noise temperature considerations. Up-link frequency powers approach 100 kW making dielectrics undesirable. Here we address some of the cases in which the straight rectangular shape may have limited usefulness. For example, grating lobes become a consideration when the bandwidth required to include the new frequency of 7.165 GHz conflicts with the desired incident angle of 30{degrees}. For this case, the cross shape`s increased packing density and bandwidth could make it desirable. When a sharp frequency response is required to separate two closely space K{sub a}-band frequencies, the stepped rectangular aperture might be advantageous. 5 refs.

Short communication.

Several closed form trajectory solutions have been developed for low-thrust interplanetary flight and used with patched conies for analysis of combined propulsion systems. The solutions provide insight into alternative types of Mars missions, and show considerable mass savings for fast crewed missions with outbound trip times on the order of 90-100 days.

Nuclear Thermal Propulsion (NTP) has been identified as a critical technology in support of the NASA Space Exploration Initiative (SEI). In order to safely develop a reliable, reusable, long-lived flight engine, facilities are required that will support ground tests to qualify the nuclear rocket engine design. Initial nuclear fuel element testing will need to be performed in a facility that supports a realistic thermal and neutronic environment in which the fuel elements will operate at a fraction of the power of a flight weight reactor/engine. Ground testing of nuclear rocket engines is not new. New restrictions mandated by the National Environmental Protection Act of 1970, however, now require major changes to be made in the manner in which reactor engines are now tested. These new restrictions now preclude the types of nuclear rocket engine tests that were performed in the past from being done today, A major attribute of a safely operating ground test facility is its ability to prevent fission products from being released in appreciable amounts to the environment. Details of the intricacies and complications involved with the design of a fuel element ground test facility are presented in this report with a strong emphasis on safety and economy.

Several new neutron cross section libraries, such as ENDF/ B-VI and IRDF-90, have recently been made available to the dosimetry community. Recommendations are made for the source selection of reaction cross sections that vary significantly among the libraries. In general, integral parameters from spectra obtained from unfold/adjustment codes using the new cross sections will not significantly change. A 61-reaction compendium of dosimetry cross sections drawn from existing evaluations has been compiled for use at the Sandia National Laboratories Radiation Metrology Laboratory. This dosimetry library (SNLRML) is recommended for use in spectrum determination with unfold/ adjustment methods. © 1992 IEEE

A rapid deployment access delay system (RAPADS) has been designed to provide high security protection of valued assets. The system or vault is transportable, modular, and utilizes a pin connection design. Individual panels are attached together to construct the vault. The pin connection allows for quick assembly and disassembly, and makes it possible to construct vaults of various sizes to meet a specific application. Because of the unique pin connection and overlapping joint arrangement, a sequence of assembly steps are required to assembly the vault. As a result, once the door is closed and locked, all pin connections are concealed and inaccessible. This provides a high level of protection in that no one panel or connection is vulnerable. This paper presents the RAPADS concept, design, fabrication, and construction.

There is an emerging interest in using thermal IR to automatically detect human intruders over wide areas. Such a capability could provide early warning beyond the perimeter at fixed sites, and could be used for portable security around mobile military assets. Sandia National Laboratories has been working on automatic detection systems based on the thermal contrast and motion of human intruders for several years, and has found that detection is sometimes difficult, depending on solar and other environmental conditions. Solar heating can dominate human thermal radiation by 100 fold, and dynamic background temperature changes can limit detector sensitivity. This paper explains those conditions and energy transfer mechanisms that lead to difficult thermal detection. We will not cover those adverse conditions that are more widely understood and previously reported on, such as fog, smoke, rain and falling snow. This work was sponsored by the Defense Nuclear Agency.

In the wavenumber-domain method of SAR imaging, frequencydomain radar data are used to reconstruct a portion of the 2-D Fourier transform of the scene, which is then inverted to create the image. The method suffers no inherent limits on aperture length or scene size. This paper extends the concept to the case where the synthetic aperture is not a straight line and the samples are unevenly spaced. An accumulation formula for wavenumberdomain reconstruction is derived and shown to be equivalent to earlier algorithms in the uniform-aperture case. It is then shown how data with three-dimensional irregularity in the aperture can be processed using height correction and mapping into the slant plane.

CIRCE2 is a cone-optics computer code for determining the flux distribution and total incident power upon a receiver, given concentrator and receiver geometries, sunshape (angular distribution of incident rays from the sun-disk), and concentrator imperfections such as surface roughness and random deviation in slope. Statistical methods are used to evaluate the directional distribution of reflected rays from any given point on the concentrator, whence the contribution to any point on the target can be obtained. DEKGEN2 is an interactive preprocessor which facilitates specification of geometry, sun models, and error distributions. The CIRCE2/DEKGEN2 package equips solar energy engineers with a quick, user-friendly design and analysis tool for study/optimization of dish-type distributed receiver systems. The package exhibits convenient features for analysis of 'conventional' concentrators, and has the generality required to investigate complex and unconventional designs. Among the more advanced features are the ability to model dish or faceted concentrators and stretched-membrane reflectors, and to analyze 3-D flux distributions on internal or external receivers with 3-D geometries. Facets of rectangular, triangular, or circular projected shape, with profiles of parabolic, spherical, flat, or custom curvature can be handled. Provisions for shading, blocking, and aperture specification are also included. This paper outlines the features and capabilities of the new package, as well as the theory and numerical models employed in CIRCE2.

This paper presents two parallel implementations of a knowledge-based robotic grasp generator. The grasp generator, originally developed as a rule-based system, embodies a knowledge of the associations between the features of an object and the set of valid hand shapes/arm configurations which may be used to grasp it. Objects are assumed to be unknown, with no a priori models available. The first part of this paper presents a `parallelization' of this rule base using the connectionist paradigm. Rules are mapped into a set of nodes and connections which represent knowledge about object features, grasps, and the required conditions for a given grasp to be valid for a given set of features. Having shown that the object and knowledge representations lend themselves to this parallel recasting, the second part of the paper presents a back propagation neural net implementation of the system that allows the robot to learn the associations between object features and appropriate grasps.

The Capacitors Division at Sandia National Laboratories has for many years been actively involved in developing high reliability, low-inductance, energy-storage, pulse-discharge capacitors. Development has concentrated on two dielectric systems; mica-paper and Mylar (both dry wrap and fill and FC40 liquid impregnation). Continuous design improvements are constantly being sought. For pulse discharge usage lowering the capacitor inductance can improve circuit performance. This paper describes recent efforts to improve the efficiency of low-inductance, mica-paper capacitors by reducing the inductance through optimizing the component geometry. The study focused on a 0.2 {mu}F, 4000 V mica-paper extended-foil capacitor design. The experimental matrix was a two-level, three factor with center points design, and was replicated four times to give reasonable statistics. The factors were the capacitor width, capacitor length, and electrode width, and with response functions of capacitor inductance and circuit performance. The capacitor inductance was measured by the resonance technique, and the circuit performance was evaluated by peak (discharge) current and rise time. Results show that the inductance can be minimized by choice of geometry with accompanying improvements in circuit performance.

This paper describes the plan for a test to failure of a steel containment vessel model. The test specimen proposed for this test is a scale model representing certain features of an improved BWR MARK-2 containment vessel. The objective of this test is to investigate the ultimate structural behavior of the model by incrementally increasing the internal pressure, at ambient temperature, until failure occurs. Pre- and posttest analyses will be conducted to predict and evaluate the results of this test. The main objective of these analyses to validate, by comparisons with the experimental data, the analytical methods used to evaluate the structural behavior of an actual containment vessel under severe accident conditions. This experiment is part of a cooperative program between the Nuclear Power Engineering Corporation (NUPEC), the United States Nuclear Regulatory Commission (NRC), and Sandia National Laboratories (SNL).

Logging technologies developed hydrocarbon resource evaluation have not migrated into geothermal applications even though data so obtained would strengthen reservoir characterization efforts. Two causative issues have impeded progress: (i) there is a general lack of vetted, high-temperature instrumentation, and (ii) the interpretation of log data generated in a geothermal formation is in its infancy. Memory-logging tools provide a path around the first obstacle by providing quality data at a low cost. These tools feature on-board computers that process and store data, and newer systems may be programmed to make decisions.'' Since memory tools are completely self-contained, they are readily deployed using the slick line found on most drilling locations. They have proven to be rugged, and a minimum training program is required for operator personnel. Present tools measure properties such as temperature and pressure, and the development of noise, deviation, and fluid conductivity logs based on existing hardware is relatively easy. A more complex geochemical tool aimed at a quantitative analysis of potassium, uranium and thorium will be available in about on year, and it is expandable into all nuclear measurements common in the hydrocarbon industry. A second tool designed to sample fluids at conditions exceeding 400{degrees}C is in the proposal stage. Partnerships are being formed between the geothermal industry, scientific drilling programs, and the national laboratories to define and develop inversion algorithms relating raw tool data to more pertinent information. 8 refs.

The overpressurization of a 1:6 scale reinforced concrete containment building demonstrated that liner tearing is a plausible failure mode in such structures under severe accident conditions. A combined experimental and analytical program was developed to determine the important parameters that affect liner tearing and to develop reasonably simple analytical methods for predicting when tearing will occur. Three sets of test specimens were designed to allow individual control over and investigation of the mechanisms believed to be important in causing failure of the liner plate. The series of tests investigated the effect on liner tearing produced by the anchorage system, the loading conditions, and the transition in thickness of the liner. Before testing, the specimens were analyzed using two- and three-dimensional finite element models. Based on the analysis, the failure mode and corresponding load conditions were predicted for each specimen. Test data and posttest examination of test specimens shows mixed agreement with the analytical predictions with regard to failure mode and specimen response for most tests. Many similarities were also observed between the response of the liner in the 1:6 scale reinforced concrete containment model and the response of the test specimens. This work illustrates the fact that the failure mechanism of a reinforced concrete containment building can be greatly influenced by details of liner and anchorage system design. Furthermore, it significantly increases the understanding of containment building response under severe accident conditions.

Acoustic telemetry has been a dream of the drilling industry for the past 50 years. It offers the promise of data rates which are one-hundred times greater than existing technology. Such a system would open the door to true logging-while-drilling technology and bring enormous profits to its developers. The basic idea is to produce an encoded sound wave at the bottom of the well, let it propagate up the steel drillpipe, and extract the data from the signal at the surface. Unfortunately, substantial difficulties arise. The first difficult problem is to produce the sound wave. Since the most promising transmission wavelengths are about 20 feet, normal transducer efficiencies are quire low. Compounding this problem is the structural complexity of the bottomhole assembly and drillstring. For example, the acoustic impedance of the drillstring changes every 30 feet and produces an unusual scattering pattern in the acoustic transmission. This scattering pattern causes distortion of the signal and is often confused with signal attenuation. These problems are not intractable. Recent work has demonstrated that broad frequency bands exist which are capable of transmitting data at rates up to 100 bits per second. Our work has also identified the mechanism which is responsible for the observed anomalies in the patterns of signal attenuation. Furthermore in the past few years a body of experience has been developed in designing more efficient transducers for application to metal waveguides. The direction of future work is clear. New transducer designs which are more efficient and compatible with existing downhole power supplies need to be built and tested; existing field test data need to be analyzed for transmission bandwidth and attenuation; and the new and less expensive methods of collecting data on transmission path quality need to be incorporated into this effort. 11 refs.

An effort has been undertaken to develop a brittle fracture acceptance criterion for structural components of nuclear material transportation casks. The need for such a criterion was twofold. First, new generation cask designs have proposed the use of ferritic steels and other materials to replace the austenitic stainless steel commonly used for structural components in transport casks. Unlike austenitic stainless steel which fails in a high-energy absorbing, ductile tearing mode, it is possible for these candidate materials to fail via brittle fracture when subjected to certain combinations of elevated loading rates and low temperatures. Second, there is no established brittle fracture criterion accepted by the regulatory community that covers a broad range of structural materials. Although the existing IAEA Safety Series {number sign}37 addressed brittle fracture, its the guidance was dated and pertained only to ferritic steels. Consultant's Services Meetings held under the auspices of the IAEA have resulted in a recommended brittle fracture criterion. The brittle fracture criterion is based on linear elastic fracture mechanics, and is the result of a consensus of experts from six participating IAEA-member countries. The brittle fracture criterion allows three approaches to determine the fracture toughness of the structural material. The three approaches present the opportunity to balance material testing requirements and the conservatism of the material's fracture toughness which must be used to demonstrate resistance to brittle fracture. This work has resulted in a revised Appendix IX to Safety Series {number sign}37 which will be released as an IAEA Technical Document within the coming year.

We show experimentally and theoretically that the generation of the 13-TW Hermes III electron beam can be accurately monitored, and that the beam can be accurately directed onto a high-Z target to produce a wide variety of bremsstrahlung patterns. This control allows the study of radiation effects induced by gamma rays to be extended into new parameters regimes. Finally, we show that the beam can be stably transported in low-pressure gas cells.

This paper presents the groundwork for a completely automatic 3-D hexahedral mesh generation algorithm called plastering. It is an extension of the paving algorithm developed by Blacker, where paving is a completely automatic 2-D quadrilateral meshing technique.

The transport of a chemically reactive fluid through a permeable medium is governed by many classes of chemical interactions. Dissolution/precipitation (D/P) reactions are among the interactions of primary importance because of their significant influence on the mobility of aqueous ions. In general, D/P reactions lead to the propagation of coherent waves. This paper provides an overview of the types of wave phenomena observed in one-dimensional (1D) and two-dimensional (2D) porous media for systems in which mineral D/P is the dominant type of chemical reaction. It is demonstrated that minerals dissolve in sharp waves in 1D advection-dominated transport, and that these waves separate zones of constant chemical compositions in the aqueous and mineral phases. Analytical solutions based on coherence methods are presented for solving 1D advection-dominated transport problems with constant and variable boundary conditions. Numerical solutions of diffusion-dominated transport in porous media show that sharp D/P fronts occur in this system as well. A final example presents a simple dual-porosity system with advection in an idealized fracture and solute diffusion into an adjacent porous matrix. The example illustrates the delay of contaminant release from the 2D domain due to a combination of physical retardation and chemical retardation.

A closely coupled computational and experimental aerodynamics research program was conducted on a hypersonic vehicle configuration at Mach 8. Aerodynamic force and moment measurements and flow visualization results were obtained in the Sandia National Laboratories hypersonic wind tunnel for laminar boundary layer conditions. Parabolized and iterative Navier-Stokes simulations were used to predict flow fields and forces and moments on the hypersonic configuration. The basic vehicle configuration is a spherically blunted 10{degrees} cone with a slice parallel with the axis of the vehicle. On the slice portion of the vehicle, a flap can be attached so that deflection angles of 10{degrees}, 20{degrees}, and 30{degrees} can be obtained. Comparisons are made between experimental and computational results to evaluate quality of each and to identify areas where improvements are needed. This extensive set of high-quality experimental force and moment measurements is recommended for use in the calibration and validation of computational aerodynamics codes. 22 refs.

Microstructural models of deformation of polycrystalline materials suggest that inelastic deformation leads to the formation of a corner or vertex at the current load point. This vertex can cause the response to non-proportional loading to be more compliant than predicted by the smooth yield-surface idealization. Combined compression-torsion experiments on Tennessee marble indicate that a vertex forms during inelastic flow. An important implication is that strain localization by bifurcation occurs earlier than predicted by bifurcation analysis using isotropic hardening.

Acoustic emissions and conventional strain measurements were used to follow the evolution of the damage surface and plastic potential in a limestone under triaxial compression. Confining pressures were chosen such that macroscopically, the limestone exhibited both brittle and ductile behavior. The parameters derived are useful for modeling the deformation of a pressure-dependent material and for computing when localization would occur. For modeling, simple approximations are adequate, but a more complete understanding of the evolution of the various parameters is necessary in order to calculate when localization can be expected. 11 refs., 6 figs.

Light emission microscopy is now currently used in most integrated circuit (IC) failure analysis laboratories. This tutorial is designed to benefit both novice and experienced failure analysts by providing an introduction to light emission microscopy as well as information on new techniques, such as the use of spectral signatures. The use of light emission for accurate identification and spatial localization of physical defects and failure mechanisms is presented. This includes the analysis of defects such as short circuits which do not themselves emit light. The importance of understanding the particular IC design and applying the correct electrical stimulus is stressed. A video tape is used to show light emission from pn junctions, MOS transistors, test structures, and CMOS ICs in static and dynamic electrical stimulus conditions. 27 refs.

The Thermionic System Evaluation Test (TSET) is a ground test of an unfueled Russian TOPAZ-II in-core thermionic space reactor powered by electric heaters. The facility that will be used for testing of the TOPAZ-II systems is located at the New Mexico Engineering Research Institute (NMERI) complex in Albuquerque, NM. The reassembly of the Russian test equipment is the responsibility of International Scientific Products (ISP), a San Jose, CA, company and Inertek, a Russian corporation, with support provided by engineers and technicians from Phillips Laboratory (PL), Sandia National Laboratories (SNL), Los Alamos National Laboratory (LANL), and the University of New Mexico (UNM). This test is the first test to be performed under the New Mexico Strategic Alliance agreement. This alliance consist of the PL, SNL, LANL, and UNM. The testing is being funded by the Strategic Defense Initiative Organization (SDIO) with the PL responsible for project execution.

Radioactive material transport casks use either lead or depleted uranium (DU) as gamma-ray shielding material. Stainless steel is conventionally used for structural containment. If a DU alloy had sufficient properties to guarantee resistance to failure during both nominal use and accident conditions to serve the dual-role of shielding and containment, the use of other structure materials (i.e., stainless steel) could be reduced. (It is recognized that lead can play no structural role.) Significant reductions in cask weight and dimensions could then be achieved perhaps allowing an increase in payload. The mechanical response of depleted uranium has previously not been included in calculations intended to show that DU-shielded transport casks will maintain their containment function during all conditions. This paper describesa two-part study of depleted uranium alloys: First, the mechanical behavior of DU alloys was determined in order to extend the limited set of mechanical properties reported in the literature. The mechanical properties measured include the tensile behavior the impact energy. Fracture toughness testing was also performed to determine the sensitivity of DU alloys to brittle fracture. Fracture toughness is the inherent material property which quantifies the fracmm resistance of a material. Tensile strength and ductility are significant in terms of other failure modes, however, as win be discussed. These mechanical properties were then input into finite element calculations of cask response to loading conditions to quantify the potential for claiming structural credit for DU. (The term structural credit'' describes whether a material has adequate properties to allow it to assume a positive role in withstanding structural loadings.)

Interfacial microchemical characterization is required in all aspects of surface processing as applied to transportation and utility technologies. Corrosion protection, fuel cells and batteries, wear surfaces, polymers and polymer-oxide interfaces, thin film multilayers, photoelectrochemical systems, and organized molecular assemblies are just a few examples of interfacial systems of interest to these industries. A number of materials and processing problems, both related to fundamental understanding and to monitoring manufacturing operations, have been identified where our microchemical characterization abilities need improving. Over twenty areas for research are identified where progress will contribute to improved understanding of materials and processes, improved problem-solving abilities, improved manufacturing consistency, and lower costs. Some of the highest priority areas for research include (1) developing techniques and methods with improved chemical specificity at interfaces, (2) developing fast, real-time surface and interface probes and (3) improving the cost and reliability of manufacturing monitors. Increased collaboration among University, Industry, and Government laboratories will be a prerequisite to making the required progress in a timely fashion.

A parallel processor that is optimized for real-time linear control has been developed. This modular system consists of A/D modules, D/A modules, and floating-point processor modules. The scalable processor uses up to 1,000 Motorola DSP96002 floating-point processors for a peak computational rate of 60 GFLOPS. Sampling rates up to 625 kHz are supported by this analog-in to analog-out controller. The high processing rate and parallel architecture make this processor suitable for computing state-space equations and other multiply/accumulate-intensive digital filters. Processor features include 14-bit conversion devices, low input-output latency, 240 Mbyte/s synchronous backplane bus, low-skew clock distribution circuit, VME connection to host computer, parallelizing code generator, and look-up-tables for actuator linearization. This processor was designed primarily for experiments in structural control. The A/D modules sample sensors mounted on the structure and the floating-point processor modules compute the outputs using the programmed control equations. The outputs are sent through the D/A module to the power amps used to drive the structure's actuators. The host computer is a Sun workstation. An Open Windows-based control panel is provided to facilitate data transfer to and from the processor, as well as to control the operating mode of the processor. A diagnostic mode is provided to allow stimulation of the structure and acquisition of the structural response via sensor inputs.

International Atomic Energy Agency (IAEA) inspectors must maintain continuity of knowledge on all safeguard samples, and in particular on those samples drawn from plutonium product and spent fuel input tanks at a nuclear reprocessing plant's blister sampling station. Integrity of safeguard samples must be guaranteed from the sampling point to the moment of sample analysis at the IAEA's Safeguards Analytical Laboratory (SAL Seibersdorf) or at an accepted local laboratory. These safeguard samples are drawn at a blister sampling station with inspector participation, and then transferred via a pneumatic post system to the facility's analytical laboratory. The transfer of the sample by the pneumatic post system, the arrival of the sample in the operator's analytical laboratory, and the storage of the sample awaiting analysis is very time consuming for the inspector, particularly if continuous human surveillance is required for all these activities. This process might be observed by ordinary surveillance methods, such as a video monitoring system, but again this would be cumbersome and time consuming for both the inspector and operator. This paper will describe a secure container designed to assure sample vial integrity from the point the sample is drawn to the treatment of the sample at the facility's analytical laboratory.

Understanding the mechanisms of growth during vapor-phase deposition is critical for the precise control of surface morphology required by advanced electronic device structures. Yet only relatively recently have the tools for observing this growth on an atomic-level scale become available (via scanning tunneling microscopy (STM), reflection high energy electron diffraction (RHEED) and low-energy electron microscopy (LEEM)). We present results from our own RHEED and STM measurements in which we use computer simulations to aid in determining the fundamental surface processes which contribute to.the observed structures. In this study of low-energy ion bombardment and growth on Si(001), it is demonstrated how simulations enable us to determine the dominant atomistic process.

Reflective Particle Tags were developed for uniquely identifying individual strategic weapons that would be counted in order to verify arms control treaties. These tags were designed to be secure from copying and transfer even after being lift under the control of a very determined adversary for a number of years. This paper discusses how this technology can be applied in other applications requiring confidence that a piece of equipment, such as a seal or a component of a secure, has not been replaced with a similar item. The hardware and software needed to implement this technology is discussed, and guidelines for the sign of systems that rely on these or similar randomly formed features for security applications are presented. Substitution of identical components is one of the easiest ways to defeat security seals, secure containers, verification instrumentation, and similar equipment. This technology, when properly applied, provides a method to counter this defeat scenario. This paper presents a method for uniquely identifying critical security related equipment. Guidelines for implementing identification systems based on reflective particles or similar random features without compromising their intrinsic security are discussed.

A non-contact, high-resolution laser ranging device has been incorporated into an instrument for accurately mapping the surface of WECS airfoils in the field. Preliminary scans of composite materials and bug debris show that the system has adequate resolution to accurately map bug debris and other surface contamination. This system, just recently delivered and now being debugged and optimized, will be used to characterize blade surface contamination on wind turbines. The technology used in this system appears to hold promise for application to many other measurements tasks, including a system for quickly and very accurately determining the profile of turbine blade molds and blades.

Sandia National Laboratories has completed the design and is now fabricating packages for shipment of tritium gas in conformance with 10 CFR 71. The package, referred to as the AL-SX, is quite unique in that its contents are a radioactive gas, and a large margin of safety has been demonstrated through overtesting. The AL-SX is small, 42 cm in diameter and 55 cm tall, and weighs between 55 kg empty and up to a maximum of 60 kg with contents and is designed for a 20-year service life. This paper describes the design of the AL-SX and certification testing performed on AL-SX packages and discusses containment of tritium and AL-SX manufacturing considerations.

Sandia National Laboratories is one of the nation's largest research and development (R and D) facilities and is responsible for national security programs in defense and energy with a primary emphasis on nuclear weapon R and D. However, Sandia also supports a wide variety of projects ranging from basic materials research to the design of specialized parachutes. As a multiprogram national laboratory, Sandia has much to offer both industrial and government customers in pursuing space nuclear technologies. A brief summary of Sandia's technical capabilities, test facilities, and example programs that relate to military and civilian objectives in space is presented.

Sandia National Laboratories is actively involved in testing coated particle nuclear fuels for the Space Nuclear Thermal Propulsion (SNTP) program managed by Phillips Laboratory. The testing program integrates the results of numerous in-pile and out-of-pile tests with modeling efforts to qualify fuel and fuel elements for the SNTP program. This paper briefly describes the capabilities of the Annular Core Research Reactor (in which the experiments are performed), the major in-pile tests, and the models used to determine the performance characteristics of the fuel and fuel elements. 6 refs.

The US Department of Energy's Slant Hole Completion Test Well, SHCT-1, was drilled in 1990 into gas-bearing, lenticular and blanket-shaped sandstones of the Mesaverde Formation, northwestern Colorado. The reservoirs are over-pressured, with sub-microdarcy, in situ, matrix-rock permeabilities. However, a set of sub-parallel natural fractures increases the whole-reservoir permeabilities, measured by well tests, to several tens of microdarcies. The slant hole azimuth was therefore oriented to cut across the dominant fracture strike, in order to access the natural-fracture permeability and increase drainage into the wellbore.

Advection-dominated flows occur widely in the transport of groundwater contaminants, the movements of fluids in enhanced oil recovery projects, and many other contexts. In numerical models of such flows, adaptive local grid refinement is a conceptually attractive approach for resolving the sharp fronts or layers that tend to characterize the solutions. However, this approach can be difficult to implement in practice. A domain decomposition method developed by Bramble, Ewing, Pasciak, and Schatz, known as the BEPS method, overcomes many of the difficulties. We demonstrate the applicability of the iterative BEPS ideas to finite-element collocation on trial spaces of piecewise Hermite bicubics. The resulting scheme allows one to refine selected parts of a spatial grid without destroying algebraic efficiencies associated with the original coarse grid. We apply the method to two dimensional time-dependent advection-diffusion problems.

Three methods of evaluating accelerated battery test data are described. Criteria for each method are used to determine the minimum test matrix required for accurate predictions. Other test methods involving high current discharge and real time techniques are discussed.

Computational mechanics simulation capability via the finite element method is being integrated into the FASTCAST project to allow realistic analyses of investment casting problems. Commercial and in-house software is being coupled to new, solid model based mesh generation capabilities to provide improved access to fluid, thermal and structural simulations. These simulations are being used for the validation of complex gating designs and the study of fundamental problems in casting.

This document presents recent accomplishments in engineering and science at Sandia National Laboratories. Commercial-scale parabolic troughs at the National Solar Thermal Test Facility are used for such applications as heating water, producing steam for industrial processes, and driving absorption air conditioning systems. Computerized-aided design, superconductor technology, radar imaging, soldering technology, software development breakthroughs are made known. Defense programs are exhibited. And microchip engineering applications in test chips, flow sensors, miniature computers, integrated circuits, and microsensors are presented.

Diffraction peaks can occur as unidentifiable peaks in the energy spectrum of an x-ray spectrometric analysis. Recently, there has been increased interest in oriented polycrystalline films and epitaxial films on single crystal substrates for electronic applications. Since these materials diffract x-rays more efficiently than randomly oriented polycrystalline materials, diffraction peaks are being observed more frequently in x-ray fluorescent spectra. In addition, micro x-ray spectrometric analysis utilizes a small, intense, collimated x-ray beam that can yield well defined diffraction peaks. In some cases these diffraction peaks can occur at the same position as elemental peaks. These diffraction peaks, although a possible problem in qualitative and quantitative elemental analysis, can give very useful information about the crystallographic structure and orientation of the material being analyzed. The observed diffraction peaks are dependent on the geometry of the x-ray spectrometer, the degree of collimation and the distribution of wavelengths (energies) originating from the x-ray tube and striking the sample.

Geologic materials are often modeled with discrete spheres because the material is not continuous and discrete spherical models simplify the mathematics. Spherical element models have been created using assemblages of spheres with a specified particle size distribution or by assuming the particles are all the same size and making the assemblage a close-packed array of spheres. Both of these approaches yield a considerable amount of material dilatation upon movement. This has proven to be unsatisfactory for sedimentary rock formations that contain bedding planes where shear movement can occur with minimal dilatation of the interface. A new concept referred to as packing angle has been developed to allow the modeler to build arrays of spheres that are the same size but have the rows of spheres offset from each other. ne row offset is a function of the packing angle and allows the modeler to control the dilatation as rows of spheres experience relative horizontal motion.

The syntheses and physical properties of {kappa}-(ET){sub 2}Cu[N(CN){sub 2}]X (X=Br and Cl) are summarized. The {kappa}-(ET){sub 2}Cu[N(CN){sub 2}]Br salt is the highest {Tc} radical-cation based ambient pressure organic superconductor ({Tc}=11.6 K), and the {kappa}-(ET){sub 2}Cu[N(CN){sub 2}]Cl salt becomes a superconductor at even higher {Tc} under 0.3 kbar hydrostatic pressure ({Tc}=12.8 K). The similarities and differences between {kappa}-(ET){sub 2}Cu[N(CN){sub 2}]Br and {kappa}-(ET){sub 2}Cu(NCS){sub 2} ({Tc}=10.4 K) are presented. The X-ray structures at 127 K reveal that the the S{hor_ellipsis}S contacts shorten between ET dimers in the former compound while the S{hor_ellipsis}S contacts shorten within dimers in the latter. The difference in their ESR linewidth behavior is also explained in terms of the structural differences. A semiconducting compound, (ET)Cu[N(CN){sub 2}]{sub 2}, isolated during {kappa}-(ET){sub 2}Cu[N(CN){sub 2}]Cl synthesis is also reported. The ESR measurements of the {kappa}-(ET){sub 2}Cu[N(CN){sub 2}]Cl salt indicate that the phase transition near 40 K is similar to the spin density wave transition in (TMTSF){sub 2}SbF{sub 6}. A new class of organic superconductors, {kappa}-(ET){sub 2}Cu{sub 2}(CN){sub 3} and {kappa}-(ET){sub 2}Cu{sub 2}(CN){sub 3}-{delta}Br{delta}, is reported with {Tc}`s of 2.8 K (1.5 kbar) and 2.6 K (1 kbar), respectively.

Nuclear weapons system designers and safety analysts are contemplating broader use of probabilistic risk assessment techniques. As an aid to their understanding, this document summarizes the development and use of probabilistic risk assessment (PRA) techniques in the nuclear power industry. This report emphasizes the use of PRA in decision making with the use of case studies. Nuclear weapon system designers and safety analysts, contemplating the broader use of PRA techniques, will find this document useful.

This document contains implementation details for the Quality Information Management System (QIMS) Pilot Project, which has been released for VAX/VMS systems using the INGRES RDBMS. The INGRES Applications-By-Forms (ABF) software development tool was used to define the modules and screens which comprise the QIMS Pilot application. These specifications together with the QIMS information model and corresponding database definition constitute the QIMS technical specification and implementation description presented herein. The QIMS Pilot Project represents a completed software product which has been released for production use. Further extension projects are planned which will release new versions for QIMS. These versions will offer expanded and enhanced functionality to meet further customer requirements not accommodated by the QIMS Pilot Project.

A large buildup in interface traps has been observed in commercial and radiation-hardened MOS transistors at very long times after irradiation (> 10{sup 6} s). This latent buildup may have important implications for CMOS response in space. 13 refs.

Translations of two pioneering Russian papers on antenna theory are presented. The first paper provides a treatise on finite-length dipole antennas; the second paper addresses infinite-length, impedance-loaded transmitting antennas.

A new approach for solving two-dimensional clustering problems is presented. The method is based on an inhibitory template which is applied to each pair of dots in a data set. Direct clustering of the pair is inhibited (allowed) if another dot is present (absent), respectively, within the area of the template. The performance of the method is thus entirely determined by the shape of the template. Psychophysical experiments have been used to define the template shape for this work, so that the resulting method requires no pattern-dependent adjustment of any parameters. The novel concept of a psychophysically-defined template and the absence of adjustable parameters set this approach apart from previous work. The useful grouping performance of this approach is demonstrated with the successful grouping of a variety of dot patterns selected from the clustering literature.

Sandia National Laboratories (SNL) Environmental Restoration (ER) Program has recently implemented a highly structured CS{sup 2} required by DOE. It is a complex system which has evolved over a period of a year and a half. During the implementation of this system, problem areas were discovered in cost estimating, allocation of management costs, and integration of the CS{sup 2} system with the Sandia Financial Information System. In addition to problem areas, benefits of the system were fund in the areas of schedule adjustment, projecting personnel requirements, budgeting, and responding to audits. Finally, a number of lessons were learned regarding how to successfully implement the system.

Ferroelectric PZT 53:47 thin films were prepared by two different solution deposition methodologies. Both routes utilized carboxylate and alkoxide precursors and acetic acid, which served as both a solvent and a chemical modifier. We have studied the effects of solution preparation conditions on film microstructure and ferroelectric properties, and have used NMR spectroscopy to characterize chemical differences between the two precursor solutions. Films prepared by a sequential precursor addition (SPA) process were characterized by slightly lossy hysteresis loops, with a P{sub r} of 18.7 {mu}C/cm{sup 2} and an E{sub c} of 55.2 kV/cm. Films prepared by an inverted mixing order (IMO) process were characterized by well saturated hysteresis loops, a P{sub r} of 26.2 {mu}C/cm{sup 2} and an E{sub c} of 43.3 kV/cm. While NMR investigations indicated that the chemical environments of both the proton and carbon species were similar for the two processes, differences in the amounts of by-products (esters, and therefore, water) formed were noted. These differences apparently impacted ceramic microstructure. Although both films were characterized by a columnar growth morphology, the SPA derived film displayed a residual pyrochlore layer at the film surface, which did not transform into the stable perovskite phase. The presence of this layer resulted in poor dielectric properties and lossy ferroelectric behavior.

We have developed a video detection algorithm for measuring the residue left on a printed circuit board after a soldering process. Oblique lighting improves the contrast between the residue and the board substrate, but also introduces an illumination gradient. The algorithm uses the Boundary Contour System/Feature Contour System to produce an idealized clean board image by discounting the illuminant, detecting trace boundaries, and filling the trace and substrate regions. The algorithm then combines the original input image and ideal image using mathematical models of the normal and inverse Weber Law to enhance the residue on the traces and substrate. The paper includes results for a clean board and one with residue.

CEPXS/ONELD is a discrete ordinates transport code package that can model the electron-photon cascade from 100 MeV to 1 keV. The CEPXS code generates fully-coupled multigroup-Legendre cross section data. This data is used by the general-purpose discrete ordinates code, ONELD, which is derived from the Los Alamos ONEDANT and ONETRAN codes. Version 1.0 of CEPXS/ONELD was released in 1989 and has been primarily used to analyze the effect of radiation environments on electronics. Version 2.0 is under development and will include user-friendly features such as the automatic selection of group structure, spatial mesh structure, and S{sub N} order.

Changing the focus of a corporate compensation and performance review system from process orientation to data base orientation results in a more integrated and flexible design. Data modeling of the business system provides both systems and human resource professionals insight into the underlying constants of the review process. Descriptions of the business and data modeling processes are followed by a detailed presentation of the data base model. Benefits derived from designing a system based on the model include elimination of hard-coding, better audit capabilities, a consistent approach to exception processing, and flexibility of integrating changes in compensation policy and philosophy.

This paper will address the purpose, scope, and approach of the Department of Energy Tiger Team Assessments. It will use the Tiger Team Assessment experience of Sandia National Laboratories at Albuquerque, New Mexico, as illustration.

One of the common waste streams generated throughout the nuclear weapon complex is hardware'' originating from the nuclear weapons program. The activities associated with this hardware at Sandia National Laboratories (SNL) include design and development, environmental testing, reliability and stockpile surveillance testing, and military liaison training. SNL-designed electronic assemblies include radars, arming/fusing/firing systems, power sources, and use-control and safety systems. Waste stream characterization using process knowledge is difficult due to the age of some components and lack of design information oriented towards hazardous constituent identification. Chemical analysis methods such as the Toxicity Characteristic Leaching Procedure (TCLP) are complicated by the inhomogeneous character of these components and the fact that many assemblies have aluminum or stainless steel cases, with the electronics encapsulated in a foam or epoxy matrix. In addition, some components may contain explosives, radioactive materials, toxic substances (PCBs, asbestos), and other regulated or personnel hazards which must be identified prior to handling and disposal. In spite of the above difficulties, we have succeeded in characterizing a limited number of weapon components using a combination of process knowledge and chemical analysis. For these components, we have shown that if the material is regulated as RCRA hazardous waste, it is because the waste exhibits one or more hazardous characteristics; primarily reactivity and/or toxicity (Pb, Cd).

The discrete Fourier transform and power spectral density are often used in analyzing data from analog-to-digital converters. These analyses normally apply a window to the data to alleviate the effects of leakage. This paper describes how windows modify the magnitude of a discrete Fourier transform and the level of a power spectral density computed by Welch's method. For white noise, the magnitude of the discrete Fourier transform at a fixed frequency has a Rayleigh probability distribution. For sine waves with an integer number of cycles and quantization noise, the theoretical values of the amplitude of the discrete Fourier transform and power spectral density are calculated. We show how the signal-to-noise ratio in a single discrete Fourier transform or power spectral density frequency bin is related to the normal time-domain definition of the signal-to-noise ratio. The answer depends on the discrete Fourier transform length, the window type and the function averaged.

The UNIX LANs in 1500 are experiencing explosive growth. The individual departments are creating LANs to address their particular needs; however, at the same time, shared software tools between the departments are becoming more common. It is anticipated that users will occasionally need access to various department software and/or LAN services, and that support personnel may carry responsibilities which require familiarization with multiple environments. It would be beneficial to users and support personnel if the various department environments share some basic similarities, allowing somewhat transparent access. This will become more important when departments share specific systems, as 1510 and 1550 have proposed with an unclassified UNIX system. Therefore, standards/conventions on the department LANs and the central site systems have to be established to allow for these features. it should be noted that the goal of the UEC is to set standards/conventions which affect the users and provide some basic structure for software installation and maintenance; it is not the intent that all 1500 LANs be made identical at an operating system and/or hardware level. The specific areas of concern include: (1) definition of a non-OS file structure; (2) definition of an interface for remote mounted file systems; (3) definition of a user interface for public files; (4) definition of a basic user level environment; and (5) definition of documentation requirements for public files (shared software). Each of these areas is addressed in this paper.

This document contains implementation details for the Sandia Management Restructure Study Team (MRST) Prototype Information System, which resides on a Sun SPARC II workstation employing the INGRES RDBMS. The INGRES/Windows 4GL application editor was used to define the components of the two user applications which comprise the system. These specifications together with the MRST information model and corresponding database definition constitute the MRST Prototype Information System technical specification and implementation description presented herein. The MRST Prototype Information System represents a completed software product which has been presented to the Management Restructure Study Team to support the management restructing processes at Sandia National Laboratories.

Finite element analyses of oil-filled caverns were performed to investigate the effects of cavern depth on surface subsidence and storage loss, a primary performance criteria of SPR caverns. The finite element model used for this study was axisymmetric, approximating an infinite array of caverns spaced at 750 ft. The stratigraphy and cavern size were held constant while the cavern depth was varied between 1500 ft and 3000 ft in 500 ft increments. Thirty year simulations, the design life of the typical SPR cavern, were performed with boundary conditions modeling the oil pressure head applied to the cavern lining. A depth dependent temperature gradient of 0.012{degrees}F/ft was also applied to the model. The calculations were performed using ABAQUS, a general purpose of finite element analysis code. The user-defined subroutine option in ABAQUS was used to enter an elastic secondary creep model which includes temperature dependence. The calculations demonstrated that surface subsidence and storage loss rates increase with increasing depth. At lower depths the difference between the lithostatic stress and the oil pressure is greater. Thus, the effective stresses are greater, resulting in higher creep rates. Furthermore, at greater depths the cavern temperatures are higher which also produce higher creep rates. Together, these factors result in faster closure of the cavern. At the end of the 30 year simulations, a 1500 ft-deep cavern exhibited 4 percent storage loss and 4 ft of subsidence while a 3000 ft-deep cavern exhibited 33 percent storage loss and 44 ft of subsidence. The calculations also demonstrated that surface subsidence is directly related to the amount of storage loss. Deeper caverns exhibit more subsidence because the caverns exhibit more storage loss. However, for a given amount of storage loss, nearly the same magnitude of surface subsidence was exhibited, independent of cavern depth.

This economic analysis compares human and robotic TRUPACT unloading at the Waste Isolation Pilot Plant. Robots speed up the unloading process, reduce human labor requirements, and reduce human exposure to radiation. The analysis shows that benefit/cost ratios are greater than one for most cases using government economic parameters. This suggests that robots are an attractive option for the TRUPACT application, from a government perspective. Rates of return on capital investment are below 15% for most cases using private economic parameters. Thus, robots are not an attractive option for this application, from a private enterprise perspective.

This paper summarizes the results of aging, condition monitoring, and accident testing of Class 1E cables used in nuclear power generating stations. Three sets of cables were aged for up to 9 months under simultaneous thermal ({approximately}100{degrees}C) and radiation ({approximately}0.10 kGy/hr) conditions. After the aging, the cables were exposed to a simulated accident consisting of high dose rate irradiation ({approximately}6 kGy/hr) followed by a high temperature steam (up to 400{degrees}C) exposure. A fourth set of cables, which were unaged, was also exposed to the accident conditions. The cables that were aged for 3 months and then accident tested were subsequently exposed to a high temperature steam fragility test (up to 400{degrees}C), while the cables that were aged for 6 months and then accident tested were subsequently exposed to a 1000-hour submergence test in a chemical solution. The results of these tests do not indicate any reason to believe that many popular nuclear power plant cable products cannot inherently be qualified for 60 years of operation for conditions simulated by this testing. Mechanical measurements (primarily elongation, modulus, and density) are more effective than electrical measurements for monitoring age-related degradation. In the high temperature steam test, ethylene propylene rubber (EPR) cable materials generally survived to higher temperatures than crosslinked polyolefin (XLPO) cable materials. In dielectric testing after the submergence testing, the XLPO materials performed better than the EPR materials.

This paper describes several different types of constraints that can be placed on multilayered feedforward neural networks which are used for automatic target recognition (ATR). We show how unconstrained networks are likely to give poor generalization on the ATR problem. We also show how the ATR problem requires a special type of classifier called a one-class classifier. The network constraints come in two forms: architectural constraints and learning constraints. Some of the constraints are used to improve generalization, while others are incorporated so that the network will be forced to perform one-class classification. 14 refs

Foams, like most highly structured fluids, exhibiting rheological behavior that is both fascinating and complex. We have developed microrheological models for uniaxial extension and simple shearing flow of a dry', perfectly ordered, three-dimensional foam composed of thin films with uniform surface tension T and negligible liquid content. We neglect viscous flow in the thin films and examine large elastic-plastic deformations of the foam. The primitive undeformed foam structure is composed of regular space-filling tetrakaidecahedra, which have six square and eight hexagonal surfaces. This structure possesses the film-network topology that is necessary to satisfy equilibrium: three films meet at each edge, which corresponds to a Plateau border, and four edges meet at vertex. However, to minimize surface energy, the films must meet at equal angles of 120{degrees} and the edges must join at equal tetrahedral angles of cos{sup {minus}1}({minus}1/3) {approx} 10.947{degree}. No film in an equilibrium foam structure can be a planar polygon because no planar polygon has all angles equal to the tetrahedral edge. In the equilibrium foam structure known as Kelvin's minimal tetrakaidecahedron, the squares' are planar quadrilateral surfaces with curved edges and the hexagons' are non-planar saddle surfaces with zero mean curvature. As the foam structure evolves with the macroscopic flow, each film maintains zero mean curvature because the pressure is the same in every bubble. In general, the shape of each thin film, defined by z = h(x,y), satisfies R{sub 1}/1 + R{sub 2}/1 = {del}{center dot} (1 + {vert bar}{del}h{vert bar}){sup {1/2}} = O where R{sub 1}{sup {minus}1} and A{sub 2}{sup {minus}1} are the principal curvatures. The appropriate boundary conditions correspond to three films meeting at equal angles. For the homogeneous deformations under consideration, the center of each film moves affinely with the flow. 5 refs

We have measured the atmospheric isoplanatic angle in the near infrared by correlating widely separated time-resolved stellar images.

Renewable energy technologies convert naturally occurring phenomena into useful energy forms. These technologies use resources that generally are not depleted, such as the direct energy (heat and light) from the sun and the indirect results of its impact on the earth (wind, falling water, heating effects, plant growth), gravitational forces (the tides), and the heat of the Earth's core (geothermal), as the sources from which they produce useful energy. These very large stores of natural energy represent a resource potential that is incredibly massive -- dwarfing that of equivalent fossil energy resources. The magnitude of these resources is, therefore, not a key constraint on energy production. However, they are generally diffuse and not fully accessible, some are intermittent, and all have distinct regional and local variability. It is these aspects of their character that give rise to difficult, but generally solvable, technical, institutional, and economic challenges inherent in development and use of renewable energy resources. This report discusses the technologies and their associated energy source.

Theoretical models have been formulated describing the dynamic behavior of the swelling and contracting of polyelectrolyte gels. This paper presents a method of weighted residuals approach to solving the governing system of equations by finite element analysis. The modulation of the imbibition of solvent by a spherical gel is studied.

There is considerable interest in the use of chemically vapor deposited (CVD) polycrystalline diamond films in advanced materials technology. However, most of the potential applications of CVD diamond films require well-controlled properties which depend on the film structure, and in turn, on the conditions under which the films are synthesized. The structure of the vapor-deposited diamond films is frequently characterized by Raman spectroscopy. Despite extensive research, much work still needs to be completed to understand the various features of the Raman spectra and to understand how the processing variables affect the spectral features. This paper examines the Raman spectra of diamond films prepared by a hot-filament-assisted CVD process as a function of substrate processing and deposition parameters.

Many applications of national importance require the design, analysis, and simulation of complex electromagnetic phenomena. These applications range from the simulation of synthetic aperture radar to the design and analysis of low-observable platforms, antenna design, and automatic target recognition. In general, the modeling of complex electromagnetic phenomena requires significant amounts of computer time and capacity on conventional vector supercomputers but takes far less on massively parallel computers. Sandia National Laboratories is currently developing massively parallel methods and algorithms for the characterization of complex electromagnetic phenomena. The goal of on going research at Sandia is to understand the characteristics, limitations, and trade-offs associated with complex electromagnetic systems including: modeling the seeker response to complex targets in clutter, calculating the radiation and scattering from conformal communication and radar system antennas, and the analysis and design of high speed circuitry. By understanding the theoretical underpinnings of complex electromagnetic systems it is possible to achieve realistic models of system performance. The first objective is the development of computationally practical, high fidelity, systems models targeted for massively parallel computers. Research to achieve this objective is conducted in such areas as mathematical algorithms, problem decomposition, inter-processor communication schemes, and load balancing. The work in mathematical algorithms includes both the development of new methods and the parallel implementation of existing techniques. The second objective is the application of these high fidelity models to facilitate a better understanding of systems level performance for many C{sup 3}I platforms. This presentation describes applications of much current interest and novel solution techniques for these applications utilizing massively parallel processing techniques.

A neighboring external control problem is formulated for a hypersonic glider to execute a maximum-terminal-velocity descent to a stationary target. The resulting two-part, feedback control scheme initially solves a nonlinear algebraic problem to generate a nominal trajectory to the target altitude. Secondly, a neighboring optimal path computation about the nominal provides a lift and side-force perturbations necessary to achieve the target downrange and crossrange. On-line feedback simulations of the proposed scheme and a form of proportional navigation are compared with an off-line parameter optimization method. The neighboring optimal terminal velocity compares very well with the parameter optimization solution and is far superior to proportional navigation. 8 refs.

This paper describes the design of an inverse adaptive filter, using the Least-Mean-Square (LMS) algorithm, the correct data taken with an analog filter. The gradient estimate used in the LMS algorithm is based upon the instantaneous error, e{sup 2}(n). Minimizing the mean-squared-error does not provide an optimal solution in this specific case. Therefore, another performance criterion, error power, was developed to calculate the optimal inverse model. Despite using a different performance criterion, the inverse filter converges rapidly and gives a small mean-squared-error. Computer simulations of this filter are also shown in this paper.

Intense light ion beams are being developed to drive inertial confinement fusion (ICF) targets. Recently, intense proton beams have been used to drive two different types of targets in experiments on the Particle Beam Fusion Accelerator. The experiments focused separately on ion deposition physics and on implosion hydrodynamics. In the ion deposition physics experiments, a 3--4 TW/cm{sup 2} proton beam heated a low-density foam contained within a gold cylinder with a specific power deposition exceeding 100 TW/gm for investigating ion deposition, foam heating, and generation of x-rays. The significant results from these experiments included the following: the foam provided an optically thin radiating region, the uniformity of radiation across the foam was good, and the foam tamped the gold case, holding it in its original position for the 15 ns beam pulse width.

This document describes the Temperature Monitoring System for the RHEPP project at Sandia National Laboratories. The system is designed to operate in the presence of severe repetitive high voltage and electromagnetic fields while providing real time thermal data on component behavior. The thermal data is used in the design and evaluation of the major RHEPP components such as the magnetically switched pulse compressor and the linear induction voltage adder. Particular attention is given to the integration of commercially available hardware and software components with a custom written control program. While this document is intended to be a reference guide, it may also serve as a template for similar applications. 3 refs.

This bibliography contains 34 references concerning utilizing benchmarking in the management of businesses. Books and articles are both cited. Methods for gathering and utilizing information are emphasized. (GHH)

Measurements have recently been conducted and computer models constructed to determine the coupling of lightning energy into munition storage bunkers as detailed in companion conference papers. In this paper transfer functions from the incident current to the measured parameters are used to construct simple circuit models that explain much of the important observed quantitative and qualitative information and differences in transfer functions are used to identify nonlinearities in the response data. In particular, V{sub oc} -- the open-circuit voltage generated between metal objects in the structure, I{sub sc} -- the short-circuit current generated in a wire connecting metal objects in the structure, and a typical current measurement in the buried counterpoise system behave in a relatively simple manner explainable by one or several circuit elements. The circuit elements inferred from measured data are comparable in magnitude with those developed from simple analytical models for inductance and resistance. These analytical models are more useful in predicting bounding electromagnetic environment values rather than providing exact time domain waveforms. 2 refs.

The restoration of environmentally contaminated sites at DOE facilities has become a major effort in the past several years. The variety of wastes involved and the differing characteristics have driven the development of new restoration and monitoring technologies. One of the new remediation technologies is being demonstrated at the Savannah River Site near Aiken, South Carolina. In conjunction with this demonstration, a new technology for site characterization and monitoring of the remediation process has been applied by Sandia National Laboratories.

We used surface-profile data taken with a noncontact laser profilometer to determine the aperture distribution within a natural fracture and found the surfaces and apertures to be isotropic. The aperture distribution could be described equally well by either a normal or a lognormal distribution, although we had to adjust the standard deviation to 'fit' the data. The aperture spatial correlation varied over different areas of the fracture, with some areas being much more correlated U= others. The fracture surfaces did not have a single fractal dimension over all length scales, which implied that they were not self-similar. We approximated the saturated flow field in the fracture by solving a finite-difference discretization of the fluid-flow continuity equation in two dimensions. We then calculated tracer breakthrough curves using a particle-tracking method. comparing the breakthrough curves obtained using both coarse- and fine-resolution aperture data (0.5- and 0.05-mm spacing between points, respectively) over the same subset of the fracture domain suggests that the spacing between the aperture data points must be less than the correlation length to obtain accurate predictions of fluid flow and tracer transport. In the future, we will perform tracer experiments and numerical modeling studies to determine exactly how fine the aperture data resolution must be (relative to the correlation length) to obtain accurate predictions.

Sandia National Laboratories (SNL) designs, tests and operates a variety of accelerators that generate large amounts of high energy Bremsstrahlung radiation over an extended time. Typically groups of similar accelerators are housed in a large building that is inaccessible to the general public. To facilitate independent operation of each accelerator, test cells are constructed around each accelerator to shield it from the radiation workers occupying surrounding test cells and work-areas. These test cells, about 9 ft. high, are constructed of high density concrete block walls that provide direct radiation shielding. Above the target areas (radiation sources), lead or steel plates are used to minimize skyshine radiation. Space, accessibility and cost considerations impose certain restrictions on the design of these test cells. SNL Health Physics division is tasked to evaluate the adequacy of each test cell design and compare resultant dose rates with the design criteria stated in DOE Order 5480.11. In response SNL-Health Physics has undertaken an intensive effort to asses existing radiation shielding codes and compare their predictions against measured dose rates. This paper provides a summary of the effort underway and its results.

The last decade has offered many challenges to the welding metallurgist: new types of materials requiring welded construction, describing the microstructural evolution of traditional materials, and explaining non-equilibrium microstructures arising from rapid thermal cycle weld processing. In this paper, the author will briefly review several advancements made in these areas, often citing specific examples of where new insights were required to describe new observations, and to show how traditional physical metallurgy methods can be used to describe transformation phenomena in advanced, non-traditional materials. The paper will close with comments and suggestions as to the needs required for continued advancement in the field.

Phase II of the Long Valley Exploratory Well was completed to a depth of 7588 feet in November 1991. The drilling comprised two sub-phases: (1) drilling 17-1/2 inch hole from the Phase I casing shoe at 2558 feet to a depth of 7130 feet, plugging back to 6826 feet, and setting 13-3/8 inch casing at 6825 feet, all during August--September 1991; and (2) returning in November to drill a 3.85-inch core hole deviated out of the previous wellbore at 6868 feet and extending to 7588 feet. Ultimate depth of the well is planned to be 20,000 feet, or at a bottomhole temperature of 500{degrees}C, whichever comes first. Total cost of this drilling phase was approximately $2.3 million, and funding was shared about equally between the California Energy Commission and the Department of Energy. Phase II scientific work will commence in July 1992 and will be supported by DOE Office of Basic Energy Sciences, DOE Geothermal Division, and other funding sources.

Recently, significant progress has been made in using finite-difference analysis cod es to simulate the responses of complex structures due to direct lightning. Advances have been made in interfacing a finite-difference code with commercial computer aided design tools, in suppressing a weak instability associated with the thin-wire algorithm for modeling conductors much smaller than a cell size, and in visualizing the results with color movies. Preliminary comparisons between the results of the finite-difference code and the results obtained during a recent rocket-triggered lightning test are also presented.

Sandia National Laboratories and ICI Explosives USA have worked together since 1987 to develop computer modeling techniques for Rock Blasting. A result of this effort is the computer program DMC (Distinct Motion Code) which was developed for two-dimensional simulation of rock motion following a blast (Taylor and Preece, 1989 1992). This program has been used to study blasting-induced rock motion resulting from oil shale mining and has been coupled with a gas flow computation capability for better treatment of the explosive behavior. This past year it has been customized for simulations of bench blasting in coat mines and rock quarries (Preece and Knudsen, 1992b). The explicit descretized nature of DMC gives it an advantage over previous blast modeling programs because subtle differences, such as row delay timing, have an influence on the results. This paper will present a DMC study of the influence on percent cast of row delay timing in a typical coal mine bench blast.

The Yucca Mountain Site Characterization Project is studying Yucca Mountain in southwestern Nevada as a potential site for a high-level nuclear waste repository. Site characterization includes surface-based and underground testing. Analyses have been performed to design site characterization activities with minimal impact on the ability of the site to isolate waste, and on tests performed as part of the characterization process. One activity of site characterization is the construction of an Exploratory Studies Facility, consisting of underground shafts, drifts, and ramps, and the accompanying surface pad facility and roads. The information in this report addresses the following topics: (1) a discussion of the potential effects of surface construction water on repository-performance, and on surface and underground experiments; (2) one-dimensional numerical calculations predicting the maximum allowable amount of water that may infiltrate the surface of the mountain without affecting repository performance; and (3) two-dimensional numerical calculations of the movement of that amount of surface water and how the water may affect repository performance and experiments. The results contained herein should be used with other site data and scientific/engineering judgement in determining controls on water usage at Yucca Mountain. This document contains information that has been used in preparing Appendix I of the Exploratory Studies Facility Design Requirements document for the Yucca Mountain Site Characterization Project.

The focus of this paper is on changes in perceptions of the risks associated with nuclear waste management over time. In particular, we are interested in the kinds of change that take place when the management programs, and those who are charged with implementing them, are subject to intensive public debate over an extended period of time. We are undertaken an over-time study of perceived risks in Colorado and New Mexico by implementing sequential random household surveys in each state, timed at six month intervals. This study employs three of these surveys, spanning the period from summer, 1990 to summer, 1991. Using these data, we examine the dynamics that may underlie variations in perceived risks over time. In particular, our analysis is focused on changes in the roles played by (1) basic political orientations (i.e. political ideology) and (2) trust in those who advocate conflicting policy positions.

Midway Valley, located at the eastern base of the Yucca Mountain in southwestern Nevada, is the preferred location of the surface facilities for the potential high-level nuclear waste repository at Yucca Mountain. One goal in siting these surface facilities is to avoid faults that could produce relative displacements in excess of 5 cm in the foundations of the waste-handling buildings. This study reviews existing geologic and geophysical data that can be used to assess the potential for surface fault rupture within Midway Valley. Dominant tectonic features in Midway Valley are north-trending, westward-dipping normal faults along the margins of the valley: the Bow Ridge fault to the west and the Paintbrush Canyon fault to the east. Published estimates of average Quaternary slip rates for these faults are very low but the age of most recent displacement and the amount of displacement per event are largely unknown. Surface mapping and interpretive cross sections, based on limited drillhole and geophysical data, suggest that additional normal faults, including the postulated Midway Valley fault, may exist beneath the Quaternary/Tertiary fill within the valley. Existing data, however, are inadequate to determine the location, recency, and geometry of this faulting. To confidently assess the potential for significant Quaternary faulting in Midway Valley, additional data are needed that define the stratigraphy and structure of the strata beneath the valley, characterize the Quaternary soils and surfaces, and establish the age of faulting. The use of new and improved geophysical techniques, combined with a drilling program, offers the greatest potential for resolving subsurface structure in the valley. Mapping of surficial geologic units and logging of soil pits and trenches within these units must be completed, using accepted state-of-the-art practices supported by multiple quantitative numerical and relative age-dating techniques.

Sandia National Laboratories (SNL) is a Department of Energy multiprogram engineering and scientific facility with unique design, development, and test capabilities arising from their work in nuclear weapons, energy resources, defense systems, nuclear safeguards, and specialized scientific endeavors. To support these programs, they have developed instrumentation and telemetry expertise not available elsewhere. This technology is applicable to projects in government and industry. Since the 1950s, they have applied our technical competence to meet difficult challenges with innovative solutions to data acquisition and telemetry problems. Sandia - with experience in fields as diverse as parachute design and plasma physics, geology and rocket guidance, human factors and high-speed aerodynamics, non-destructive testing and satellite communications - can use the power of synergism among our many disciplines to solve your complex problems of data and acquisition and analysis. SNL solves difficult data acquisition problems for extreme environments with expertise in advanced telemetry techniques, high data rate telemetry design, specialized electronics packaging, MIL-STD-1553 communications, instrumentation development, real-time data analysis, project management, specialized testers and data encryption.

Pretest analysis of a heated block test, proposed for the Exploratory Studies Facility at Yucca Mountain, Nevada, was conducted in this investigation. Specifically, the study focuses on the evaluation of the various designs to drill holes and cut slots for the block. The thermal/mechanical analysis was based on the finite element method and a compliant-joint rock-mass constitutive model. Based on the calculated results, relative merits of the various test designs are discussed.

Photovoltaic energy systems have historically been treated as a bulk power generation source for the future. However, utilities and other agencies involved with electrification throughout the world are beginning to find photovoltaics a least-cost option to meet specific loads both for themselves and their customers, in both off-grid and grid-connected applications. These expanding markets offer the potential of hundreds of megawatts of sales in the coming decade, but a strategy addressing both industrial growth and user acceptance is necessary to capitalize on this opportunity. 11 refs.

Phase mixing of transverse oscillations changes the nature of the ion hose instability from an absolute to a convective instability. The stronger the phase mixing, the faster an electron beam reaches equilibrium with the guiding ion channel. This is important for long distance propagation of relativistic electron beams where it is desired that transverse oscillations phase mix within a few betatron wavelengths of injection and subsequently an equilibrium is reached with no further beam emittance growth. In the linear regime phase mixing is well understood and results in asymptotic decay of transverse oscillations as 1/Z{sup 2} for a Gaussian beam and channel system, Z being the axial distance measured in betatron wavelengths. In the nonlinear regime (which is likely mode of propagation for long pulse beams) results of the spread mass model indicate that phase mixing is considerably weaker than in the regime. In this paper we consider this problem of phase mixing in the nonlinear regime. Results of the spread mass model will be shown along with a simple analysis of phase mixing for multiple oscillator models. Particle simulations also indicate that phase mixing is weaker in nonlinear regime than in the linear regime. These results will also be shown. 3 refs., 4 figs.

Photovoltaic (PV) systems are increasing in popularity in the northern latitudes and in the arctic regions in the state of Alaska. This increased interest and the high cost of providing electric power in these remote areas have prompted the Alaska Energy Authority (AEA) to request assistance from the Photovoltaic Design Assistance Center at Sandia National Laboratories. A project to investigate the feasibility of using PV-Diesel hybrid power systems in small villages in Alaska was started in 1989. Data acquisition systems (DAS) were designed and installed in selected villages to obtain resource and load information. The DAS is described and village electrical and resource data are presented. Simulations were run using the collected village data and actual cost data provided by the AEA. Results of the simulations and the economic analysis are presented. 5 refs., 8 figs.

Fabrication of high-efficiency silicon solar cells in an industrial environment requires a different optimization than in a laboratory environment. Strategies are presented for process development of high-efficiency silicon solar cells, with a goal of simplifying technology transfer into an industrial setting. The strategies emphasize the use of statistical experimental design for process optimization, and the use of baseline processes and cells for process monitoring and quality control. 8 refs.

The purpose of this paper is to develop an analytical model to convert ballistic limit curves obtained from flat projectile experiments to ballistic limit curves based on equivalent diameter spheres. Results from a test program involving flat plat projectiles conducted at Sandia National Laboratories are compared against the predicted performance of equivalent spherical projectiles as determined from the Wilkinson and Cour-Palais penetration equations. The developed method demonstrates good correlation of the ballistic limit of the shield concept for the flat plate projectiles to the theoretical ballistic limit for equivalent spheres as predicted by the penetration equations. 3 refs.

PRA studies are being extended to include a wider spectrum of reactor plants than was considered in NUREG-1150. There is a need for computationally simple models for Direct Containment Heating (DCH) that could be used for screening studies aimed at identifying potentially significant contributors to risk. This paper discusses two adiabatic equilibrium models that are candidates for the task. The first, a 1-cell model, places a true upper bound on DCH loads. This upper bound, however, often far exceeds reasonable expectations of containment loads based on best estimate CONTAIN calculations or experiment observations. In this paper, a 2-cell model is developed that largely captures the major mitigating features of containment compartmentalization, thus providing more reasonable estimates of the containment load. Predictions of the equilibrium models are compared with experiment data from the Limited Flight Path (LFP) test series conducted at Sandia National Laboratories.

The CONTAIN code is currently being used to predict containment thermal hydraulic conditions during design basis and severe accidents for advanced light water reactor (ALWR) designs such as the Westinghouse AP600. In the AP600 design, a passive containment cooling system (PCCS) is used for reducing long-term overpressure during accidents. CONTAIN models for heat and mass transfer within the AP600 containment and outer air cooling channel are verified by comparing recent CONTAIN calculations to integral test data obtained by Westinghouse in their PCCS Integral Test Facility. The comparison includes test in which the outer containment wall is both dry and wet, that is, the wet tests involve an evaporative water film that enhances heat transfer as will be the case for AP600. The appropriateness of the heat and mass transfer analogy methodology used in the CONTAIN code is demonstrated. Code model limitations are discussed along with model development plans and applications for AP600.

An additive three step process has been developed for patterned deposition of Cu onto poly(tetrafluoroethylene) (PTFE). The first step involves patterned irradiation with X-rays or electrons which is thought to cross link the PTFE surface; step two involves chemical etching with the result that only the non-irradiated areas are etched; and step three involves selective chemical vapor deposition (CVD) of Cu onto the etched surface at 200 C using (hexafluoroacetylacetonato)Cu(I) trimethylphosphine ((hfac)Cu(PMe{sub 3})). The non-irradiated areas of the surface are covered by a continuous, dense Cu film with X-ray photoelectron spectra show to contain only surface impurities that are easily removed by a short Ar ion sputter. The irradiated areas show the presence of only C and F, characteristic of PTFE.

The first experiment of the Integral Effects Test (IET-1) series was conducted to investigate the effects of high pressure melt ejection (HPME) on direct containment heating (DCH). A 1:10 linear scale model of the Zion reactor pressure vessel (RPV), cavity, instrument tunnel, and subcompartment structures were constructed in the Surtsey Test Facility at Sandia National Laboratories (SNL). The RPV was modelled with a melt generator that consisted of a steel pressure barrier, a cast MgO crucible, and a thin steel inner liner. The melt generator/crucible had a semi-hemispherical bottom head containing a graphite limitor plate with a 3.5 cm exit hole to simulate the ablated hole in the RPV bottom head that would be formed by tube ejection in a severe nuclear power plant (NPP) accident. The reactor cavity model contained 3.48 kg of water with a depth of 0.9 cm that corresponded to condensate levels in the Zion plant. A steam driven iron oxide/aluminum/chromium thermite was used to simulate HPME. A relatively small steam explosion occurred in the cavity during IET-1. Steam blowthrough entrained debris into the Surtsey vessel resulting in a peak pressure increase in Surtsey of 98 kPa. The Surtsey vessel had been previously inerted with N{sub 2}. The total debris mass ejected into the Surtsey vessel was 43 kg. The hydrogen concentration was 3.1 mol.% in the vessel at equilibrium. The concentration measured inside the subcompartment structures immediately following HPME transient was 20.7 mol.% H{sub 2}. 4 refs., 17 figs., 5 tabs.

During the RADLAC II open-air beam propagation experiments this last year three separate optical diagnostics were used. (1) Streak cameras were deployed to measure matched beam radius and centroid versus time. (2) Three gated, intensified TV cameras were used to image the beam from the end of the propagation range. They gave beam radius and centroid for three slices of the beam over a five meter propagation length. (3) Open shutter cameras were developed to give the time-averaged beam position over the entire propagation range. Data from all three diagnostics were digitized, stored in files on a computer, and post-processed to give temporally and spatially resolved beam size and position. These diagnostics used beam induced air-fluorescence as the mechanism to provide a prompt signal representative of the beam current density. Previous experiments and analysis have shown that the radiation is prompt with the intensity proportional to the beam current density for high energy, high current electron beams propagating in full density air.

The technical issues brought about by recent federal mandates are reviewed and discussed. Progress made in the elimination of CFCs is briefly reviewed. The problems, implications, and status of pending anti-lead legislation and taxation are discussed at length. Recommendations are made for the enactment of rational, fair, and orderly legislation and taxation.

This paper describes current research and development on a miniaturized sensing system for use during in situ characterization of nuclear waste storage tanks. Sandia is designing this sensing system as a tool for a large robotic arm that is deployed through an access port in the top of a storage tank. While the robot arm scans the sensing package over the waste, a distributed computing system acquires sensor data, correlates the data with the position of the robot, and produces maps of the chemical and radiological contents of the tanks in real time. We have built and demonstrated a first prototype system containing eight sensors. 53 refs.

Two revisions of the CONTAIN code, CONTAIN 1.11 and 1.12 , have recently been released. The purpose of this paper is to highlight the new features of these revisions and to discuss other new code features currently under development. The features of CONTAIN 1.11 discussed here include a quasi-mechanistic concrete outgassing model, the connected structure option for heat conduction between compartments, and a new approach for modeling forced convective heat transfer. The direct containment heating (DCH) models released as part of CONTAIN 1.12 are also discussed. New code features currently under development include a revised gas combustion model and a new multifield DCH model. New features of the revised combustion model include the treatment of spontaneous recombination and diffusion flames. CONTAIN plant calculations comparing the old and the revised combustion models are presented. The new features of the multifield DCH model are discussed, and demonstration calculations using this model to analyze a small scale experiment are presented.

The Department of Energy`s (DOE`s) Office of Civilian Radioactive Waste Management (OCRWM) is in the process of developing a new generation of casks to transport spent fuel from commercial nuclear reactor facilities to federal waste facilities. In evaluating the needs of the cask development program a number of unresolved technical issues with potential impacts on the transportation system were identified. This paper provides three samples of issues being addressed by the Cask Systems Development Program for technical resolution: (1) burn-up credit, (2) containment source term evaluation, and (3) weeping.

SMILE is a coaxial Self Magnetically Insulated Transmission Line voltage adder. It replaces the original beam line of the RADLAC II accelerator by a 12.5 m long cathode electrode. The anode electrode remains practically the same, consisting of the original eight insulating stacks or feeds which are connected with equal diameter stainless steel cylinders. The beam is produced at the end of the accelerator and is free of all the possible instabilities associated with accelerating gaps and magnetic vacuum transport. Annular beams with {beta}{perpendicular} {le} 0.1 and radius r{sub b} {le} 1 cm were routinely obtained and extracted from a small magnetically-immersed foilless electron diode. Results of the experimental evaluation are presented and compared with design parameters and numerical simulation predictions. 4 refs.

Abstract not provided.

In this paper, measurements on the quasi-isentropic compression of tungsten to stress levels of 250 GPa are reported. Results of these experiments have been compared to those obtained under shock loading conditions to comparable stresses. These experiments have allowed the determination of temperature, pressure, and loading rate effects on the dynamic yield strength of tungsten up to 250 GPa. These results show that the dynamic yield strength of tungsten is dependent on the loading rate with the strength being higher for the relatively slower rates of loading along the quasi-isentropic. The pressure dependence of the yield strength of tungsten is determined nearly independent of temperature effects from quasi-isentropic loading experiments to 250 GPa, because the temperature rise in an quasi-loading experiment is much lower than those associated with shock loading experiments.

Continuum dynamics codes are categorized as Lagrangian or Eulerian according to the motion of the mesh. A Lagrangian code`s mesh moves with the material, so no mass flows between cells. An Eulerian code`s mesh is stationary, so mass flows between the cells. Eulerian codes have improved to the point where they are routinely used to solve a broad variety of large deformation solid and fluid dynamics problems ranging from air flow over an airplane wing to meteor impact on space structures. This presentation will concentrate on multi-fluid Eulerian codes capable of modeling transient were propagation in solids. These codes use a two-step process to integrate the physics across a time step. The first step, referred to as the Lagrangian step, integrates the physics on a Lagrangian mesh across the time step. The field values are then at the new time, but they are on the distorted Lagrangian mesh. The second step, referred to as the remap step, remaps the data on the distorted Lagrangian mesh back to the original Eulerian mesh thus completing one time step. The algorithms used in the first step are similar to those used in modern Lagrangian codes but they must be extended to handle multi-material cells. The algorithms used in the second step are complex and must be very carefully chosen to minimize errors. These algorithms include second-order, monotone advection equations to calculate the quantities flowing between cells. They also require algorithms that construct material interfaces inside multi-material cells. The strength and limitations of currently used numerical techniques will be discussed. New code development activities that combine the best features on both Lagrangian and Elueian codes will also be discussed. These new codes will employ the strengths of both technologies to address problems that cannot be adequately solved at this time.

The Hybrid Thin-Slot Algorithm (HTSA) integrates a transient integral-equation solution for an aperture in an infinite plane into a finite-difference time-domain (FDTD) code. The technique was introduced for linear apertures and was extended to include wall loss and lossy internal gaskets. A general implementation for arbitrary thin slots is briefly described here. The 3-D FDTD-code TSAR was selected for the implementation. The HTSA does not provide universal solutions to the narrow slot problem, but has merits appropriate for particular applications. The HTSA is restricted to planar slots, but can solve the important case that both the width and depth of the slot are narrow compared to the FDTD spatial cell. IN addition, the HTSA is not bound to the FDTD discrete spatial and time increments, and therefore, high-resolution solutions for the slot physics are possible. The implementation of the HTSA into TSAR is based upon a ``slot data file`` that includes the cell indices where the desired slots are exist within the FDTD mesh. For an HTSA-defined slot, the wall region local to the slot is shorted, and therefore, to change the slot`s topology simply requires altering the file to include the desired cells. 7 refs.

The one-electron energy levels of icosahedral boron clusters have been calculated as a function of intericosahedral spacing maintaining the intraicosahedral spacing of {alpha}-boron. For crystalline lattice constants greater than 1.25 times the equilibrium one, band overlap occurs with concomitant metallic behavior. At smaller lattice constants, orbitals(bands) associated with bonds to adjacent icosahedra are lowered and orbitals(bands) associated with ``antibonds`` are raised. Four bands which were three quarters full become empty, while three bands which were empty become filled. This leads to an energy gap between the filled states and the empty states which accounts for the experimentally observed insulating behavior of this elemental material with three valence electrons per atom.

Verifying the velocity accuracy of a GPS receiver or an integrated GPS/INS system in a dynamic environment is a difficult proposition when many of the commonly used reference systems have velocity uncertainities of the same order of magnitude or greater than the GPS system. The results of flight tests aboard an aircraft in which multiple reference systems simultaneously collected data to evaluate the accuracy of an integrated GPS/INS system are reported. Emphasis is placed on obtaining high accuracy estimates of the velocity error of the integrated system in order to verify that velocity accuracy is maintained during both linear and circular trajectories. Three different reference systems operating in parallel during flight tests are used to independently determine the position and velocity of an aircraft in flight. They are a transponder/interrogator ranging system, a laser tracker, and GPS carrier phase processing. Results obtained from these reference systems are compared against each other and against an integrated real time differential based GPS/INS system to arrive at a set of conclusions about the accuracy of the integrated system.

Computer-aided molecular design methods were used to tailor binding sites for small substrate molecules, including CO{sub 2} and methane. The goal is to design a cavity, adjacent to a catalytic metal center, into which the substrate will selectively bind through only non-bonding interactions with the groups lining the binding pocket. Porphyrins are used as a basic molecular structure, with various substituents added to construct the binding pocket. The conformations of these highly-substituted porphyrins are predicted using molecular mechanics calculations with a force field that gives accurate predictions for metalloporhyrins. Dynamics and energy-minimization calculations of substrate molecules bound to the cavity indicate high substrate binding affinity. The size, shape and charge-distribution of groups surrounding the cavity provide molecular selectivity. Specifically, calculated binding energies of methane, benzene, dichloromethane, CO{sub 2} and chloroform vary by about 10 kcal/mol for metal octaethyl-tetraphenylporphyrins (OETPPs) with chloroform, dichloromethane, and CO{sub 2} having the lowest. Significantly, a solvent molecule is found in the cavity in the X-ray structures of Co- and CuOETPP crystals obtained from dichloromethane. 5 refs., 3 figs., 3 tabs.

Single Event Upset Imaging utilizes the scanning of a micro-focused MeV ion beams across an integrated circuit to test the upset response of the circuit to energetic heavy ions. Using this technique, the position dependence of logic state upsets, as well as the charge collection efficiency of an integrated circuit, can be directly measured with micron resolution. We present in this paper a review of a series of measurements carried out on the TA670 16K static random access memory chip which display this technique`s capabilities.

Short communication.

Hot cracking, or solidification cracking, is one of the most extensively studied phenomenon in welding metallurgy. The efforts made to identify the causes of this type of cracking have been driven by the negative commercial and engineering consequences resulting from the formation of these defects. Through judicious weld joint design, the mechanical restraint can be minimized, but it can never be entirely eliminated simply because metals expand and contract when heated and cooled, respectively. The localized nature of heat input in fusion welding insures a non-homogeneous thermal field being applied to the parts being welded, resulting in the development of strains in the as-solidifying weld metal. With the inherent limitations on the mechanical restraint factor, much research has gone into identifying those alloy compositions which minimize the microstructural factor required for hot cracking to occur. Examples from the author`s own research are presented as a tutorial to show how differential thermal analysis techniques have been used to study the chemical/microstructural factors associated with solidification and fusion zone hot cracking in nickel based engineering alloys. References to other uses of these techniques in related welding metallurgy studies are also given.

Dislocation formation in InAs{sub 1-x}Sb{sub x} buffer layers grown by metal-organic chemical vapor deposition is shown to be reproducibly enhanced by p-type doping at levels greater than or equal to the intrinsic carrier concentration at the growth temperature. To achieve a carrier concentration greater than 2 {times} 10{sup 18} cm{sup {minus}3}, the intrinsic carrier concentration of InSb at 475 C, p-type doping with diethylzinc was used. Carrier concentrations up to 6 {times} 10{sup 18} cm{sup {minus}3} were obtained. The zinc doped buffer layers have proven to be reproducibly crack free for InAs{sub 1-x}Sb{sub x} step graded buffer layers with a final composition of x = 0.12 and a strained layer superlattice with an average composition of x = 0.09. These buffer layers have been used to prepare SLS infrared photodiodes. The details of the buffer layer growth, an explanation for the observed Fermi level effect and the growth and characterization of an infrared photodiode are discussed.

The use of coatings on carbon-carbon materials to reduce the oxidation of carbon is of interest for the production of non-ablative aerospace structures. The arc-jet ground test facility can produce the high energy oxidizing environment necessary to simulate hypersonic flight in which to test candidate coatings. The test conditions usually required are characterized by material temperature and length of time the material remains at that temperature. Material specimens were exposed to high energy supersonic air exhausting from the NASA-Ames Research Center`s 20-MW arc-jet facility. The carbon-carbon materials were heated to required temperatures with arc-heated air for specified lengths of time. This report describes the test methodology and observations of those tests.

We described a new family of versatile, cascadable, optical switches with different functional characteristics -- latching, non-latching, and bistable -- using a single epitaxial structure base don the monolithic integration of photothyristors and surface-emitting layers. High performance optical switching characteristics have been achieved for all three switch archetypes. We also demonstrate the AND, OR, NAND, NOR, and INVERT optical logic functions using monolithic switch structures. 7 refs.

A boundary integral equation method for steady unsaturated flow in nonhomogeneous porous media is presented. Steady unsaturated flow in porous media is described by the steady form of the so-called Richards equation, a highly nonlinear Fokker-Planck equation. By applying a Kirchhoff transformation and employing an exponential model for the relation between capillary pressure and hydraulic conductivity, the flow equation is rendered linear in each subdomain of a piece-wise homogeneous material. Unfortunately, the transformation results in nonlinear conditions along material interfaces, giving rise to a jump in the potential along these boundaries. An algorithm developed to solve the nonhomogeneous flow problem is described and verified by comparison to analytical and numerical solutions. The code is applied to examine the moisture distribution in a layered porous medium due to infiltration from a strip source, a model for infiltration from shallow ponds and washes in arid regions.

Structural system identification is undergoing a period of renewed interest. Probabilistic approaches to physical parameter identification in analysis finite element models make uncertainty in test results an important issue. In this paper, we investigate this issue with a simple, though in many ways representative, structural system. The results of two modal parameter identification techniques are compared and uncertainty estimates, both through bias and random errors, are quantified. The importance of the interaction between test and analysis is also highlighted. 25 refs.

Pre-exposure induced stress corrosion cracking (SCC) of an Al-Li-Cu, AA 2090, was studied using a variety of test techniques. Results from SCC testing in a simulated isolated pit solution are correlated with electrochemical corrosion rate data obtained for individual phases in the subgrain boundary region. These experimental data, combined with existing data on the crevice chemistry of isolated pits in Al-Li alloys and X-ray diffraction studies of solid corrosion products formed in crevice environments are used to propose a model for pre-exposure induced cracking based on anodic dissolution along subgrain boundaries. Key features of the model are selective dissolution of the subgrain boundary T{sub 1} phase (Al{sub 2}CuLi) at the crack tip and passivation of crack walls by the formation of an Li{sub 2}[Al{sub 2}(OH){sub 6}]{sub 2}{center_dot}CO{sub 3}{center_dot}nH{sub 2}O barrier film.

The transportation risk evaluation code RADTRAN 4 is designed to evaluate doses and risks associated with the transportation of radioactive materials (Ne92). RADTRAN 4 may be used to calculate dose consequences for incident-free transportation and dose risks for accidents. Consequences of normal (or incident-free) transportation include doses to crew members, persons at stops, and members of the public sharing a route segment (on-link) and residing near the segment (off-link) during normal transportation. These dose estimates are not multiplied by a probability factor and, hence, are referred to as dose consequences. Calculated doses that might be incurred during accidents are multiplied by the probabilities of those accidents, and hence are referred to as dose risks. RADTRAN 4 includes a LINK option that allows the user to characterize each link or segment of a transportation route in greater detail than that provided by average or default values for route-related parameters.

This paper explains how an induction coilgun works and presents the factors which go into its design. Our purpose is to obtain algebraic expressions which, although crude, provide useful predictors of behavior, illustrate the dependence on various parameters, and suggest ways to optimize the design. Detailed prediction of the gun`s behavior can be obtained from simulation codes, such as SLINGSHOT.

Very high driving pressures (tens or hundreds of GPa), are required to accelerate flier plats to hypervelocities. This loading pressure pulse on the fiber plates must be nearly shockless to prevent the plate from melting or vaporizing. This is accomplished by using graded-density impactors referred to as ``pillows.`` When this graded-density material is used to impact a flier-plate in a modified two-stage light gas gun, nearly shockless megabar pressures are introduced into the flier plate. The pressure pulses must also be tailored to prevent spallation of the flier-plate. This technique has been used to launch nominally 1-mm-thick aluminum, magnesium and titanium (gram-size) intact plates to 10.4 km/s, and 0.5-mm-thick aluminum and titanium (half-gram size) intact plates to 12.2 km/s. This is the highest mass-velocity capability attained with laboratory launchers to data, and should open up new regimes of impact physics and lethality studies related to space sciences for laboratory investigations. 14 refs.

Relativistic high current electron beams can be transported long distances across the geomagnetic field using the IFR (Ion focused Regime) technique. IFR is a method of providing strong electrostatic focusing and guiding of the beam. The guiding is sufficiently strong to allow the beam to transport any angle with respect to geomagnetic field. In the IFR method, first an ionizing laser (or any ionizing method) is used to create a preionized cylindrical channel.

Very high pressure and acceleration is necessary to launch flier plates to hypervelocities. In addition, the high pressure loading must be uniform, structured, and shockless, i.e., time-dependent to prevent the flier plate from either fracturing or melting. In this paper, a novel technique is described which allows the use of 100 GPa megabar loading pressures and 10{sup 9}-g acceleration to launch intact flier plates to velocities of 12.2 km/s. The technique has been used to launch nominally 1-mm thick aluminum, magnesium and titanium alloy plates to velocities over 10 km/s, and 0.5-mm thick aluminum and titanium alloy plates to velocities of 12.2 km/s.

We present a learning algorithm designed to improve robot path planning. The algorithm relies on an existing path planner to provide solutions to difficult tasks. From these solutions, it learns a sparse network of useful robot subgoals which guide and support fast planning. We analyze the algorithm theoretically by developing some general techniques useful in characterizing behaviors of probabilistic learning. We also demonstrate the effectiveness of the algorithm empirically with an existing path planner in practical environments. The learning algorithm not only reduces the time cost of existing planners, but also increases their capability in solving difficult tasks. 7 refs.

An understanding of the state of stress on faults is important for pre- and postclosure performance considerations for the potential high-level radioactive waste repository at Yucca Mountain. This paper presents the results of three-dimensional numerical analyses that provide estimates of the state of stress through time (10,000 years) along three major faults in the vicinity of the potential repository due to thermal stresses resulting from waste emplacement. It was found, that the safety factor for slip close to the potential repository increases with time after waste emplacement. Possible fault slip is predicted above and below the potential repository for certain loading conditions and times. In general, thermal loading reduces the potential for slip in the vicinity of the potential repository.

This paper presents a summary of the conduct and findings of the Exploratory Studies Facility Alternatives Study (ESF-AS). The Exploratory Studies Facility (ESF) is being planned for use in the characterization of a site for a potential high-level nuclear waste repository at Yucca Mountain, NV. The purpose of the ESF-AS were to identify and rank order ESF-repository options and to improve understanding of the favorable or unfavorable features of the ESF design. The analysis resulted in the ranking of 34 options, in accordance with the extent to which each option could achieve the objectives. Additional findings regarding design features that were identified as key elements in an option`s ability to provide good overall performance are also discussed.

The eutectic Sn-Pb solder alloy is discussed with respect to alloy development options to improve the thermomechanical fatigue behavior of solder joints. Eutectic Sn-Pb solder joints fail through the development of a heterogeneous coarsened band of recrystallized and coarsened Pb- and Sn-rich phases. All imposed deformation concentrates solely into this thin region, accelerating fatigue failures. The development of solder alloys is currently being undertaken to improve the fatigue characteristics of eutectic Sn-Pb solder. New alloys must retain wetting and manufacturability characteristics similar to eutectic Sn-Pb. The options discussed to improve fatigue life include: creating a fine superplastic microstructure, small alloy additions to homogenize the microstructure, carbon reinforced composite solder, dispersed second phase precipitates that break up the solder microstructure, and using different solder alloys to replace eutectic Sn-Pb.

The large deformation elastic response of a plane woven Kevlar fabric is investigated analytically and experimentally. The analysis assumes the undeformed geometry to be a sequence of interlaced arcs of circles that reverse at each yarn midpoint, and each yarn is modeled as an extensible elastica subject to certain compatibility conditions. Deflection-force relations for the fabric are determined in terms of the initial weave geometry and the elastic properties of the individual yarns. The theoretical results agree well with the results of experiments performed on a fabric woven from 400 denier Kevlar yarns under conditions of uniaxial loading in both warp and fill directions.

The Faceted Stretched-Membrane Dish Program is part of a DOE-sponsored effort to develop a commercial 25 kWe dish/Stirling system employing a twelve-facet dish concentrator. The facets will utilize the stretched-membrane technology originated in the heliostat development program. Each facet is constructed with a thin metal membrane stretched over both sides of a steel ring. When a small vacuum is induced between the membranes they assume a parabolic contour capable of concentrating sunlight at a predetermined focal length. A reflective polymer film is attached to the face of the facet of the facet to enhance the optical performance. During Phase II of the Faceted Stretched-Membrane Dish Program, Science Applications International Corp. and Solar Kinetics, Inc., constructed prototype 3.5-meter facets utilizing different design approaches to demonstrate their manufacturability and optical performance. Sandia engaged in a program to determine the on-sun performance of the facets (for f/Ds of 2.7 to 3.0). A uniformly distributed slope error was used as the basis for comparison. Flux arrays based on slope error from a computer model were compared to a measured flux array for each facet. The slope error for the facet was determined by the value that would produce a modeled array with the minimum mean square difference to the measured array. The facet produced by SAIC demonstrated uniform slope errors of 2.2 to 3.0 milliradians with peak flux intesities of 334 to 416 kW/m{sup 2}. The SKI facet had slope errors of 1.6 to 1.9 milliradians with peak flux intesities of 543 to 1186 kW/m{sup 2}.

A 1-MeV neutron damage equivalence methodology and damage function have been developed for GaAs based on a recoil-energy dependent damage efficiency and the displacement kerma. This method, developed using life-time degradation in GaAs LEDs in a variety of neutron spectra, is also shown to be applicable to carrier removal. A validated methodology, such as this, is required to ensure and evaluate simulation fidelity in the neutron testing of GaAs semiconductors.

This report describes Welch's method for computing Power Spectral Densities (PSDs). We first describe the bandpass filter method which uses filtering, squaring, and averaging operations to estimate a PSD. Second, we delineate the relationship of Welch's method to the bandpass filter method. Third, the frequency domain signal-to-noise ratio for a sine wave in white noise is derived. This derivation includes the computation of the noise floor due to quantization noise. The signal-to-noise ratio and noise flood depend on the FFT length and window. Fourth, the variance the Welch's PSD is discussed via chi-square random variables and degrees of freedom. This report contains many examples, figures and tables to illustrate the concepts. 26 refs.

Four expert-judgment teams have developed analyses delineating possible future societies in the next 10,000 years in the vicinity of the Waste Isolation Pilot Plant (WIPP). Expert-judgment analysis was used to address the question of future societies because neither experimentation, observation, nor modeling can resolve such uncertainties. Each of the four, four-member teams, comprised of individuals with expertise in the physical, social, or political sciences, developed detailed qualitative assessments of possible future societies. These assessments include detailed discussions of the underlying physical and societal factors that would influence society and the likely modes of human-intrusion at the WIPP, as well as the probabilities of intrusion. Technological development, population growth, economic development, conservation of information, persistence of government control, and mitigation of danger from nuclear waste were the factors the teams believed to be most important. Likely modes of human-intrusion were categorized as excavation, disposal/storage, tunneling, drilling, and offsite activities. Each team also developed quantitative assessments by providing probabilities of various alternative futures, of inadvertent human intrusion, and in some cases, of particular modes of intrusion. The information created throughout this study will be used in conjunction with other types of information, including experimental data, calculations from physical principles and computer models, and perhaps other judgments, as input to performance assessment.'' The more qualitative results of this study will be used as input to another expert panel considering markers to deter inadvertent human intrusion at the WIPP.

This paper summarizes the results of aging, condition monitoring, and accident testing of Class 1E cables used in nuclear power generating stations. Three sets of cables were aged for up to 9 months under simultaneous thermal ({approx_equal} 100{degrees}C) and radiation ({approx_equal}0.10 kGy/hr) conditions. After the aging, the cables were exposed to a simulated accident consisting of high dose rate irradiation ({approx_equal}6 kGy/hr) followed by a high temperature steam exposure. A fourth set of cables, which were unaged, were also exposed to the accident conditions. The cables that were aged for 3 months and then accident tested were subsequently exposed to a high temperature steam fragility test (up to 400{degrees}C), while the cables that were aged for 6 months and then accident tested were subsequently exposed to a 1000-hour submergence test in a chemical solution. The results of the tests indicate that the feasibility of life extension of many popular nuclear power plant cable products is promising and that mechanical measurements (primarily elongation, modulus, and density) were more effective than electrical measurements for monitoring age-related degradation. In the high temperature steam test, ethylene propylene rubber (EPR) cable materials generally survived to higher temperatures than crosslinked polyolefin (XLPO) cable materials. In dielectric testing after the submergence testing, the XLPO materials performed better than the EPR materials. This paper presents some recent experimental data that are not yet available elsewhere and a summary of findings from the entire experimental program.

Combustion of energetic materials involves processes in both gas and condensed phases and is governed by coupled thermal, physical, and chemical phenomena. Development of reliable models for design, performance, stability, and hazard analyses requires detailed understanding of three general chemical reaction regimes: (1) initial condensed-phase decomposition, (2) subsequent interaction of decomposition products with the remaining condensed phase, and (3) gas-phase reaction of decomposition products to form the ultimate combustion products. The first two regimes are the least understood and most difficult to study, particularly the initial condensed-phase decomposition. The basic difficulty in studying condensed phase phenomena has been the inability to probe directly chemistry in the condensed phase under isothermal condition and with the spatial and temporal resolution needed at higher temperatures and reaction rates. Thin-film samples provide a means to study condensed-phase chemistry at isothermal conditions and with microsecond temporal resolution. We are developing an experiment system that employs rapidly heated thin- film samples and multiple diagnostics to examine condensed-phase chemistry and monitor evolved gas species. Results from our initial work have been encouraging. Thin-film samples of several energetic materials have been prepared and appear to be representative of bulk materials. Furthermore, preliminary experiments indicate that all the use of these samples with two chemical diagnostic techniques, time-of- flight mass spectrometry (TOFMS) and time-resolved infrared spectral photography (TRISP), is viable. 5 refs., 8 figs.

The polarimetry problem (the measurement of the radar-cross-section polarization scattering matrix) is described. Two methods of calibrating a polarimetric radar are outlined. The first is a general multiple-calibration-target (MCT) method applicable to almost any radar system. The second is a simple, single-calibration-target (SCT) method applicable to systems which use a single antenna for both transmit/receive and a reciprocal RF network. The performance of the MCT method is examined through the use of Monte Carlo simulations. Finally, the SCT method is applied to measurements from the SCATTER facility, demonstrating about 40 dB isolation between polarization components in the frequency domain and in excess of 50 dB in the range domain.

Sandia National Laboratories, Albuquerque, manages the Utility Battery Exploratory Technology Development Program, which is sponsored by the US Department of Energy`s Office of Energy Management. In this capacity, Sandia is responsible for the engineering analyses and development of rechargeable batteries for utility-energy-storage applications. This report details the technical achievements realized during fiscal year 1991. Sodium/Sulfur, Zinc/Bromine, Nickel/Hydrogen, Aluminium/Air and Lead/Acid batteries are evaluated.

This report presents the results of single-well hydraulic tests performed in seven wells in the vicinity of the Waste Isolation Pilot Plant (WIPP) site in southeastern New Mexico in 1988 and 1989. The tests discussed in this report were performed in four of the five members of the Rustler Formation. The tests include: a slug-withdrawal test of the unnamed lower member of the Rustler ate well H-16; slug-withdrawal and slug-injection tests of the Culebra Dolomite Member at well AEC-7; slug-injection tests of the Culebra at well D-268; a pumping test of the Culebra at well H-18; pulse-injection, slug-injection, and slug-withdrawal tests of Magenta Dolomite Member at well H-2b1; pulse-withdrawal, slug-withdrawal, and slug-injection tests of the Magenta at well H-3b1; and pulse-withdrawal and slug-withdrawal tests of the Forty-niner Member at well H-3d. The tests were intended to provide data on the transmissivities of the Rustler members for use in regional-scale modeling of groundwater flow through the Rustler.

The ES&H Training Catalog is a tool to assist managers in determining which training courses they require their employees to complete. The narrative description under ``Who Shall Attend`` describes the characteristics of the employees and contractors under the direction of Sandia who are required by law, regulation, DOE Order, or SNL Directive to complete the training in order to be in compliance. The narrative is ``Who Should Attend`` describes the individuals for which the course is `highly recommended,`` although they are not mandated to attend.

SANET is a computer program intended for use in constructing, evaluating, and printing event trees for safety and reliability studies. SANET allows the user to graphically construct event trees, assign probabilities to the branches on the tree and include a variety of labels. Fast, publication quality printed output can be obtained. SANET requires an IBM compatible PC with a 80286, 80386 or 80486 processor, VGA graphics, a mouse and an HP Laserjet printer.

The technological innovation process comprises a range of stages, steps, and activities extending fro generation of new ideas through successful practical application of those ideas. This process constitutes the larger context within which technology transfer programs must necessarily operate if the goal is to transform new knowledge and technology into products which are competitive in the emerging global marketplace. A basic grasp of the principles and issues involved in the total innovation process is essential for developing and improving programs, prioritizing activities, and making strategic and operational decisions which will be appropriate and effective. This report attempts to provide a relatively brief overview of the total innovation process and related issues. This focus follows from the intent of the federal technology transfer initiative, which is essentially to facilitate the rapid advance of technological progress and to enhance national economic competitiveness. It is important to recognize that the transfer of technology between organizations or individuals is only one part of the complete process, although possibly a critical part in some situations. From an economic standpoint, technology transfer without resulting successful commercialization is meaningless. This report should be useful primer for people from any sector of the economy, even though it is intended to address the context for the transfer of federal laboratory technology in particular.

Two laboratory tests were designed to study the behavior of SnTe and CsOH in steam at {approximately}1230 K with the reactor materials Inconel 600, 304 stainless steel, silver and nickel, a nonoxidizing constituent of Inconels and steels in reactor accident environments. Thermochemical calculations examined the sensitivity of species in the H-O-Cs-Te-Sn system to temperature, to hydrogen and SnTe concentrations and to total system pressure. Test results indicate that should SnTe be formed from fission product tellurium and the tin in zircaloy cladding, it may not remain stable in steam in the presence of unoxidized (or lightly oxidized) metals. Calculations show a small amount of SnTe, in equilibrium with steam, decomposes to primarily Te and SnO. It is felt that these decomposition producets react with the reactor materials since Sn and Te are seen to be deposited separately and not as SnTe. The deposition velocity for SnO vapor in the system was estimated to be 0.57 m/s. The response of CsOH in the system was similar to behavior observed previously: some cesium combined with silicon found in Inconel and stainless steel oxides. At lower temperatures ({le}940 K) CsOH corroded Inconel, stainless steel and nickel providing enhanced surface area for additional trapping of species. There was no experimental evidence for the formation of cesium telluride; vapor equilibrium calculations did not predict formation either. 33 refs., 29 figs, 7 tabs.

An analytical expression and an integral representation are presented for the contribution, Y{sup (n)} = {Sigma}{sup (n)}{delta}{Omega}{sub n}, of n-event multiple scattering chains to the observed backscattering spectrum in heavy-ion backscattering (HIBS) measurements. The approximations introduced in deriving the results are chosen such that an upper limit is placed on Y{sup (n)} by the expressions. The Rutherford elastic scattering cross section is used to describe individual collisions between incident projectiles and target atoms. Screening of the Rutherford scattering cross section is included in an approximate fashion which maintains the upper limit estimate. Inelastic energy loss between collision events is assumed proportional to the projectile velocity. Specific application of theses expressions is made to HIBS detection of trace amounts of heavy atom impurities on a Si by 200--400 keV C{sup +} beams. The predicted multiple scattering background for this applications is compared with the predicted single scattering signal for 10{sup 10} atoms/cm{sup 2} of Fe, Cu, Zr, Sn, or Au, as surface impurity. The comparison shows that the multiple scattering background poses no barrier to extending the sensitivity of HIBS detection of impurities in this mass range to levels as low as 10{sup 8} atoms/cm{sup 2} for the upper part of the energy range considered. Comparison of calculations with and without screening included show that the screening of the Rutherford cross section by atomic electrons is a significant factor in preventing multiple scattering effects from interfering with HIBS spectrometry at impurity levels in the 10{sup 10} atoms/cm{sup 2} range.

The MELCOR code has been used to simulate the FLECHT SEASET natural circulation experiments done in a scale-model Westinghouse-PWR test facility, with code results compared to experimental data. Sensitivity studies have been done, for both single-phase and two-phase natural circulation conditions, on time step effects and machine dependencies; nodalization studies and studies on several code modelling options were also done. Good agreement is found between prediction and observation for steady-state, single-phase liquid natural circulation. The code could reproduce the major thermal/hydraulic response characteristics in two-phase natural circulation, but only through a number of nonstandard input modelling modifications; MELCOR cannot reproduce the requisite physical phenomena with ``normal`` input models. Because the same response is observed in similar tests at other facilities over a range of scales and is expected to occur in full-scale plants as well, the ability of the user to ``match`` the observed behavior through a small set of nonstandard input modelling changes allows MELCOR to be used in PRA studies in which such physics are expected to be encountered, while awaiting corrections to the code models involved. The time step control algorithm in MELCOR does not run this problem efficiently; a substantial reduction in time step results in significantly less oscillation predicted at only a small increase run time.

The Waste Isolation Pilot Plant (WIPP) is planned as a mined geologic repository for the disposal of transuranic (TRU) radioactive wastes generated by defense programs of the United States Department of Energy. One of the criteria for evaluating the suitability of the WIPP for disposal of TRU wastes is compliance with the United States Environmental Protection Agency`s (EPA) standards for such facilities. The Containment Requirements of those standards require calculating cumulative releases of radionuclides to the accessible environment by all combinations of events and processes (scenarios) that may affect the escape and transport of radionuclides from the repository for 10, 000 years after decommissioning of the facility. Because the release limits established by the EPA are probabilistic, scenario probabilities are also required. A panel of experts was convened to estimate the probabilities of occurrence of the events used in scenario development and to identify additional human-intrusion events for inclusion in a safety assessment of the WIPP. This report documents the background presentations that were made to the panel about the WIPP program, regulatory guidelines, and performance-assessment program, and site-specific and regional geologic and hydrologic characteristics that may affect the WIPP disposal system.

This report is a revision and update of the original geologic site characterization report that was published in 1980. Many of the topics addressed in the earlier report were predictive in nature and it is now possible to reexamine them some 12 years later, using the data from 17 new caverns and more than ten years of SPR storage experience. Revised maps of the salt configuration show on overhand and faults on the north side of the dome, defining more clearly the edge relationships with respect to the SPR caverns. Caprock faults may locally influence the pattern of subsidence, which is occurring primarily as a result of cavern creep closure. The greater subsidence rate occurring at West Hackberry will likely require mitigative action within a few years. Seismicity of low intensity recurs infrequently at West Hackberry, but a small earthquake in 1983 caused dish rattling in the immediate vicinity.

Excavation stability in an underground nuclear waste repository is required during construction, emplacement, retrieval (if required), and closure phases to ensure worker health and safety, and to prevent development of potential pathways for radionuclide migration in the post-closure period. Stable excavations are developed by appropriate excavation procedures, design of the room shape, design and installation of rock support reinforcement systems, and implementation of appropriate monitoring and maintenance programs. In addition to the loads imposed by the in situ stress field, the repository drifts will be impacted by thermal loads developed after waste emplacement and, periodically, by seismic loads from naturally occurring earthquakes and underground nuclear events. A priori evaluation of stability is required for design of the ground support system, to confirm that the thermal loads are reasonable, and to support the license application process. In this report, a design methodology for assessing drift stability is presented. This is based on site conditions, together with empirical and analytical methods. Analytical numerical methods are emphasized at this time because empirical data are unavailable for excavations in welded tuff either at elevated temperatures or under seismic loads. The analytical methodology incorporates analysis of rock masses that are systematically jointed, randomly jointed, and sparsely jointed. In situ thermal and seismic loads are considered. Methods of evaluating the analytical results and estimating ground support requirements for all the full range of expected ground conditions are outlines. The results of a preliminary application of the methodology using the limited available data are presented. 26 figs., 55 tabs.

The Yucca Mountain Site Characterization Project is studying Yucca Mountain in southwestern Nevada as a potential site for a high-level nuclear waste repository. Site characterization includes surface-based and underground testing. Analyses have been performed to design site characterization activities with minimal impact on the ability of the site to isolate waste, and on tests performed as part of the characterization process. One activity of site characterization is the construction of an Exploratory Studies Facility, for which many design options are being considered, including shafts, drifts, and ramps. The information in this report pertains to: (1) engineering calculations of the potential distribution of residual water from constructing the shafts and drifts; (2) numerical calculations predicting the movement of residual construction water from the shaft and drift walls into the rock; and (3) numerical calculations of the movement of residual water and how the movement is affected by ventilation. This document contains information that has been used in preparing Appendix 1 of the Exploratory Studies Facility Design Requirements document for the Yucca Mountain Project.

Numerical results are presented for the Performance Assessment Calculational Exercise (PACE-90). One- and two-dimensional water and solute transport are presented for steady infiltration into Yucca Mountain. Evenly distributed infiltration rates of 0.01, 0.1, and 0.5 mm/yr were considered. The calculations of solute transport show that significant amounts of radionuclides can reach the water table over 100,000 yr at the 0.5 mm/yr rate. For time periods less than 10,000 yr or infiltrations less than 0.1 mm/yr very little solute reaches the water table. The numerical simulations clearly demonstrate that multi-dimensional effects can result in significant decreases in the travel time of solute through the modeled domain. Dual continuum effects are shown to be negligible for the low steady state fluxes considered. However, material heterogeneities may cause local amplification of the flux level in multi-dimensional flows. These higher flux levels may then require modeling of a dual continuum porous medium.

In support of the development of American National Standards Institute standards for the transport of radioactive materials, Sandia has a program to characterize the normal transport environment. This program includes both analytical modeling of package and trailer responses, and over-the-road tests to measure those responses. This paper presents the results of a series of over-the-road tests performed using Chem-Nuclear equipment in the Barnwell, SC, area. The test events included a variety of road types such as rough concrete, shock events such as railroad grade crossings, and driver responses such as sharp turns. The response of the package and trailer to these events was measured with accelerometers at various locations to determine the inertial loads. Either load cells or strain gages were used to measure tiedown response. These accelerations and loads were measured on systems with flexible and ``rigid`` tiedowns. The results indicated that while significant accelerations occur on the trailer bed, these do not translate into equivalent loads in either the package or the tiedown system. This indicates that trailer-bed response should not be used in determining the load factor for fatigue calculations of the package components or in determining design loads for tiedowns.

Currently, there are several Greater Confinement Disposal (GCD) boreholes at the Radioactive Waste Management Site (RWMS) for the Nevada Test Site. These are intermediate-depth boreholes used for the disposal of special case wastes, that is, radioactive waste within the Department of Energy complex that do not meet the criteria established for disposal of high-level waste, transuranic waste, or low-level waste. A performance assessment is needed to evaluate the safety of the GCD site, and to examine the feasibility of the GCD disposal concept as a disposal solution for special case wastes in general. This report documents the effort in defining all the waste inventory presently disposed of at the GCD site, and the inventory and release model to be used in a performance assessment for compliance with the Environmental Protection Agency`s 40 CFR 191.

Cementitious materials, together with other materials, are being considered to seal a potential repository at Yucca Mountain. A concern with cementitious materials is the chemical and mineralogic changes that may occur as these materials age while in contact with local ground waters. A combined theoretical and experimental approach was taken to determine the ability to theoretically predict mineralogic changes. The cementitious material selected for study has a relatively low Ca:Si ratio approaching that of the mineral tobermorite. Samples were treated hydrothermally at 200{degrees}C with water similar to that obtained from the J-13 well on the Nevada Test Site. Post-test solutions were analyzed for pH as well as dissolved K, Na, Ca, Al, and Si. Solid phases formed during these experiments were characterized by scanning electron microscopy and X- ray diffraction. These findings were compared with predictions made by the geochemical modeling code EQ3NR/E06. It was generally found that there was good agreement between predicted and experimental results.

Two years ago, researchers at Sandia National Laboratories showed that a massively parallel computer with 1024 processors could solve scientific problems more than 1000 times faster than a single processor. Since then, interest in massively parallel processing has increased dramatically. This review paper discusses some of the applications of this emerging technology to important problems at Sandia. Particular attention is given here to the impact of massively parallel systems on applications related to national defense. New concepts in heterogenous programming and load balancing for MIMD computers are drastically increasing synthetic aperture radar (SAR) and SDI modeling capabilities. Also, researchers are showing that the current generation of massively parallel MIMD and SIMD computers are highly competitive with a CRAY on hydrodynamic and structural mechanics codes that are optimized for vector processors.

Analysis of an intermittent failure to write the "1" state to a particular memory location at low temperature (-55° C) in a 16K x 1 CMOS SRAM is presented. The failure was found to be due to an open metallization at a metal-to-silicon contact. The root cause of the failure was poor step coverage of the metallization over an oxide step. A variety of failure analysis techniques including dynamic electron beam analysis at low temperature using a Peltier cold stage were employed to study the intermittently failing SRAM. The failure site was located by using capacitive coupling voltage contrast analysis. PSPICE simulation, light emission microscopy, scanning electron microscopy, and focused-ion beam techniques were used to confirm the failure mechanism and location. The write cycle time of the failed IC was abnormally long, but within the allowable tester limit. The vulnerability of other ICs to failure by open metallization in metal-to silicon contacts is reviewed.

We present calculations which show the radial dependence of the KVV and L₂₃VV Auger matrix elements of silicon. We find greatly differing dependences, converging within ~1 a.u. of the nucleus in the case of the KVV, but not until ~4 a.u. in the case of the L₂₃VV, well beyond the bond midpoint of ~2.2 a.u. We also find quite different dependences for the various elements within a particular CVV transition. Because the local density of states (LDOS) is dependent on the radius of the sphere of integration, our results suggest that different CVV Auger processes on the same atom in fact probe different LDOSs, as do even different contributions within the same transition. (This effect is separate from the well-known matrix element property which weights angular-momentum components differently.) These results call into question both the single-site LDOS approximation when used in the interpretation of low-energy (<100 eV) Auger spectra, and the application to high-energy spectra of local densities of states obtained by integration over muffin-tin or Wigner–Seitz spheres which have a large radius compared to the region probed by the Auger process.

Two-dimensional Acousto-Optic (AO) correlators differ from the frequency plane correlators in that multiplying, shifting, and adding, rather than Fourier transforming are used to obtain the correlations. Thus, many of the available composite filter design techniques are not aimed at designing filters for use in AO correlators since they yield frequency-domain functions. In this paper, a method is introduced for designing filter impulse responses of arbitrary extent for implementation on AO correlators. These filters are designed to yield sharp correlation peaks. Simulation results are included to illustrate the viability of the proposed approach. Also included are some initial results from the first successful use of grey-scale composite filters on an AO correlator.

Two active Li/SOCl2 cells for use in artillery-fired atomic projectiles are being developed. Voltage delay is the primary mode of electrochemical failure in these cells at -35°C. To minimize this anode polarization, the anode passivation is inhibited by adding chloromethyl chlorosulfate (CMCS) to the sulfur dioxide complex of lithium tetrachloroaluminate (LiAlCl4-SO2) in the cell electrolyte. One battery powers the telemetry system (TM battery) and the other powers a projectile event timer circuit (PET battery). The authors utilize the PET battery and PET load profile to demonstrate the effect of electrolyte additives on anode passive film growth and associated voltage delay. Similar effects were also observed in the TM battery. A limited number of PET prototypes was available for this study. Therefore, several tests were performed in hermetically sealed prismatic laboratory test cells which were constructed using the same electrochemical components which are used in the PET cells.

The Waste Isolation Pilot Plant (WIPP), in southeastern New Mexico, is a research and development facility to demonstrate safe disposal of defense-generated transuranic waste. The US Department of Energy will designate WIPP as a disposal facility if it meets the US Environmental Protection Agency's standard for disposal of such waste; the standard includes a requirement that estimates of cumulative releases of radioactivity to the accessible environment be incorporated in an overall probability distribution. The WIPP Project has chosen an approach to calculation of an overall probability distribution that employs the concept of scenarios for release and transport of radioactivity to the accessible environment. This report reviews the use of Monte Carlo methods in the calculation of an overall probability distribution and presents a logical and mathematical foundation for use of the scenario concept in such calculations. The report also draws preliminary conclusions regarding the shape of the probability distribution for the WIPP system; preliminary conclusions are based on the possible occurrence of three events and the presence of one feature: namely, the events attempted boreholes over rooms and drifts,'' mining alters ground-water regime,'' water-withdrawal wells provide alternate pathways,'' and the feature brine pocket below room or drift.'' Calculation of the WIPP systems's overall probability distributions for only five of sixteen possible scenario classes that can be obtained by combining the four postulated events or features.

A combined experimental and analytical study of strains developed in encapsulated assemblies during casting, curing and thermal excursions is described. The experimental setup, designed to measure in situ strains, consisted of thin, closed-end, Kovar tubes that were instrumented with strain gages and thermocouples before being over-cast with a polymeric encapsulant. Four bisphenol A (three diethanolamine cured and one anhydride cured) epoxy-based materials and one urethane elastomeric material were studied. After cure of the encapsulant, tube strains were measured over the temperature range of {minus}55{degrees}C to 90{degrees}C. The thermal excursion experiments were then numerically modeled using finite element analyses and the computed strains were compared to the experimental strains. The predicted strains were over estimated (conservative) when a linear, elastic, temperature-dependent material model was assumed for the encapsulant and the stress free temperature T{sub i} was assumed to correspond to the cure temperature {Tc} of the encapsulant. Very good agreement was obtained with linear elastic calculations provided that the stress free temperature corresponded to the onset of the glassy-to-rubbery transition range of the encapsulant. Finally, excellent agreement was obtained in one of the materials (828/DEA) when a viscoelastic material model was utilized and a stress free temperature corresponding to the cure temperature was assumed. 13 refs., 20 figs., 3 tabs.

Surface damage has been observed on the rails of rocket sled tracks and on the barrels of high-velocity guns. The phenomenon is generally referred to as ``ongoing``. Damage to a stationary surface (guider) is created from the oblique impact of a high-velocity object (slider) moving over its surface. The surface damage (gouge) is typically a shallow crater in the shape of a teardrop with the leading edge characterized by the wider end and a slightly raised lip. For rocket sleds, rail gouging occurs when the sled velocity is greater than 1.5 km/sec; while in guns, barrel gouging occurs when the velocity exceeds 4 km/sec. A model is developed to describe the phenomenon of gouging. An unbalanced slider randomly causes a shallow-angle, oblique impact between the slider and the guider. At sufficiently high velocity, the impact produces a thin, but very hot, layer of soft material at the contact surface. Under the action of a moving load, the soft layer lends itself to an antisymmetric deformation and a gouge is formed when this soft material is over-run by the slider. The model is simulated numerically with a hydrodynamic (CTH) code. The results of the simulations are in good agreement with the observed phenomena. Based on the simulated temperature and pressure profiles at the contact surface, design criteria for gouge mitigation are developed in this study. 45 refs., 29 figs., 1 tab.

A description of the Remote Area Monitoring System utilized on nuclear tests conducted by Sandia National Laboratories and the Defense Nuclear Agency is presented. The configuration of the detectors as used on a test is described, as well as the system hardware. Calibration of the detectors before fielding is also discussed.

The annular Core Research Reactor (ACRR) Source Term (ST) Experiment program was designed to obtain time-resolved data on the release of fission products from irradiated fuels under well-controlled light water reactor severe accident conditions. The ST-1 Experiment was the first of two experiments designed to investigate fission product release. ST-1 was conducted in a highly reducing environment at a system pressure of approximately 0.19 MPa, and at maximum fuel temperatures of about 2490 K. The data will be used for the development and validation of mechanistic fission product release computer codes such as VICTORIA.

There are four papers contained in this report which were presented at the Nuclear Energy Agency (NEA) Gas Workshop to provide information about studies of waste-generated gas being conducted for the Waste Isolation Pilot Plant (WIPP). The paper by Davies et al. provides a general overview of the physical conditions pertinent to waste-generated gas and of the coupling of chemical, hydrologic, and structural processes. The paper by Brush et al. describes specific gas-generation processes and the laboratory- and bin-scale experiments being carried out to characterize these processes. The paper by Mendenhall et al. describes coupled modeling of gas generation and room closure, and provides an analysis of the potential for fracture generation and growth. the paper by Webb describes a series of sensitivity calculations carried out to assess the importance of hydrologic parameters, such as formation permeability and two-phase characteristic curves. Together, these papers provide an overview of the present (September 1991) status of waste-generated gas studies for the WIPP.

A three dimensional pretest finite element analysis of the Intermediate Scale Borehole Test has been performed. In the analysis, the 7.7 years simulation period includes the mining of Rooms C1 and C2, and the N1420 cross drift, at time zero; drilling of the borehole between the two rooms at 5.7 years; and 2 years of post-drilling response. An all salt configuration was used in the calculation. The 1984 Waste Isolation Pilot Plant (WIPP) reference elastic-secondary creep law, with reduced elastic moduli, was used to model the creeping response of the salt. Results show that after mining of the rooms and cross drift a relatively high von Mises stress state exists around the perimeter of the pillar. However, by 5.7 years, or immediately prior to drilling of the borehole, the pillar has relaxed to an almost uniform von Mises stress of about 7--8 MPa. After the borehole is drilled, a relatively high von Mises stress field is once again set up in the immediate vicinity of the hole. This drives the creep closure of the borehole. The hole closes more in the vertical direction than in the horizontal direction, resulting in ovalling of the hole. At the end of the simulation, the von Mises stress around the borehole is still higher than that in the remained of the pillar. Thus, the closure rates are relatively high at the end of the simulation time.

A parametric model for releases of radionuclides from spent-nuclear-fuel containers in a waste repository is presented. The model is appropriate for use in preliminary total-system performance assessments of the potential repository site at Yucca Mountain, Nevada; for this reason it is simpler than the models used for detailed studies of waste-package performance. Terms are included for releases from the spent fuel pellets, from the pellet/cladding gap and the grain boundaries within the fuel pellets, from the cladding of the fuel rods, and from the radioactive fuel-assembly parts. Multiple barriers are considered, including the waste container, the fuel-rod cladding, the thermal ``dry-out``, and the waste form itself. The basic formulas for release from a single fuel rod or container are extended to formulas for expected releases for the whole repository by using analytic expressions for probability distributions of some important parameters. 39 refs., 4 figs., 4 tabs.

The design of the potential Yucca Mountain repository is subject to many thermal goals related to the compliance of the site with federal regulations. This report summarizes a series of sensitivity studies that determined the expected temperatures near the potential repository. These sensitivity studies were used to establish an efficient loading scheme for the spent fuel canisters and a maximum areal power density based strictly on thermal goals. Given the current knowledge of the site, a design-basis areal power density of 80 kW/acre can be justified based on thermal goals only. Further analyses to investigate the impacts of this design-basis APD on mechanical and operational aspects of the potential repository must be undertaken before a final decision is made.

The electrical and test properties of several logic gate open circuit defect structures were measured. Results indicate that tunneling current across fine geometry discontinuities enables low frequency operation of Integrated Circuits (ICs). No significant capacitive coupling was observed for adjacent metal interconnect or for large metal opens on the gate interconnects. These results indicate the need for different methods of open circuit defect detection during test.

A previous investigation of laser-induced damage mechanisms and corresponding thresholds in step-index, multimode fibers was motivated by an interest in optical systems for firing explosives. In the initial study, the output from a compact, multimode Nd/YAG laser was coupled into fiber cores of pure fused silica. End-face polishing steps were varied between successive fiber lots to produce improved finishes, and each fiber was subjected to a sequence of progressively increasing energy densities up to a value of more than 80 J/cm². Essentially all of the tested fibers experienced a 'laser conditioning' process at the front fiber face, in which a visible plasma was generated for one or more laser shots. Rather than produce progressive damage at the front surface, however, this process would eventually cease and leave the surface with improved damage resistance. Once past this conditioning process, the majority of fibers damaged at the rear end face. Other modes of damage were observed either at locations of fixturing stresses or at a location of high static tensile stress resulting from bends introduced to the fiber. Although the previous results were encouraging in terms of achieving useful damage thresholds, a number of areas for further study were indicated. In the present study, a similar experimental procedure was used to address these areas. The relative permanence of front-surface laser conditioning was examined by re-testing fibers that had experienced this process at least a year previously. End-face mechanical polishing was again examined by testing fibers prepared using a refined polishing schedule. Attempts to use a single fixture to hold an entire lot of fibers throughout end-face polishing and damage testing met with mixed results, with fiber positions subjected to fixturing stresses likely sites for initial damage. In an effort to prepare fiber faces with the improved damage resistance observed with front faces following 'laser conditioning,' two schedules for CO₂-laser polishing of end faces were developed and evaluated. Finally, to improve resistance to damage at sites with significant static stresses, fiber samples which passed a much higher tensile proof test during manufacturing were tested. The current experiments were conducted with a new laser having a shorter pulse width and a significantly different mode structure. The beam was injected into the fiber using a geometry that had been successful in the previous study in minimizing a damage mechanism which can occur at the core/cladding interface with the first few hundred fiber diameters. However, the different mode structure of the new laser apparently resulted in this mechanism dominating the current results.

The refractory metals of Groups 5B and 6B and their alloys display a variety of unique physical and mechanical characteristics in addition to their high melting points. In turn, these characteristics make these materials strong candidates for severe service and specialized applications. However, these materials also present a variety of challenges with respect to both fabrication weldability and the in-service behavior of weldments, many of which are related to the dominant effects of interstitial impurities. This work reviews current understanding of the physical and joining metallurgy of these metals and their alloys with emphasis on fusion welding. Of specific interest are the role of impurities and alloy chemistry in fabrication and service weldability, the material processing route, eg. vacuum melting vs. powder metallurgy, the importance of welding process procedures and variables, weldment mechanical properties, and fracture behavior. Specific examples from the various alloy systems are used to illustrate general metallurgical and joining characteristics of this class of materials.

Resistance Welding (RW) has been known for about a century and in common use for much of that time. Much knowledge has been accumulated concerning many aspects of the process. However, upon examining contemporary RW handbooks, a few subjects that have been "overlooked" were found. Usually, this oversight will not be important; however, when the RW process is being applied at its limits, these factors may become critical. In this paper we will discuss such overlooked'' factors as the Peltier and Thomson effects, and the dynamics of welding head motions and how they are affected by the current pulse. Examples taken from sheet metal and microwelding applications will be given as examples.

Basic to our knowledge of the science of welding is an understanding of the melting efficiency, which indicates how much of the heat deposited by the welding process is used to produce melting. Recent calorimetric studies of GTAW, PAW, and LBW processes have measured the net heat input to the part thereby quantifying the energy transfer efficiency and in turn permitting an accurate determination of the melting efficiency. It is indicated that the weld process variables can dramatically affect the melting efficiency. This limiting value is shown to depend on the weld heat flow geometry as predicted by analytical solutions to the heat flow equation and as demonstrated by the recent empirical data. A new dimensionless parameter is used to predict the melting efficiency and is shown to correlate extremely well with recent empirical data. This simple prediction methodology is notable because it requires only a knowledge of the weld schedule and the material properties in order to estimate melting efficiency.

Current and future needs in automative, aircraft, space, military, and well logging industries require operation of electronics at higher temperatures than today's accepted limit of 395 K. Without the availability of high-temperature electronics, many systems must operate under derated conditions or must accept severe mass penalties required by coolant systems to maintain electronic temperatures below critical levels. This paper presents ongoing research and development in the electronics community to bring high-temperature electronics to commercial realization. Much of this work was recently reviewed at the First International High-Temperature Electronics Conference held 16--20 June 1991 in Albuquerque, New Mexico. 4 refs., 1 tab.

Upward Feedback is a program that gives employees and opportunity to anonymously provide their manager with feedback concerning the manager's job performance. It is an opportunity for managers to receive confidential feedback evaluating their implementation of corporate values and management behaviors as perceived by those who work for them. This feedback can come from employees who report directly to the manager, that is, one level below them (referred to as direct reports), or from those two reporting levels below them (referred to as skip-level reports). Managers then share information with their employees in feedback meetings and develop action plans to address areas of concern. Sandia National Laboratories has developed and implemented an Upward Feedback Pilot Program and follow up survey. This paper discussed the program and the lessons learned.

C++ is the first object-oriented programming language which produces sufficiently efficient code for consideration in computation-intensive physics and engineering applications. In addition, the increasing availability of massively parallel architectures requires novel programming techniques which may prove to be relatively easy to implement in C++. For these reasons, Division 1541 at Sandia National Laboratories is devoting considerable resources to the development of C++ libraries. This document describes the first of these libraries to be released, PHYSLIB, which defines classes representing Cartesian vectors and (second-order) tensors. This library consists of the header file physlib.h, the inline code file physlib.inl, and the source file physlib.C. The library is applicable to both three-dimensional and two-dimensional problems; the user selects the 2-D version of the library by defining the symbol TWO D in the header file physlib.h and recompiling physlib.C and his own code. Alternately, system managers may wish to provide duplicate header and object modules of each dimensionality. This code was produced under the auspices of Sandia National Laboratories, a federally-funded research center administered for the United States Department of Energy on a non-profit basis by AT T. This code is available to US citizens, and institutions under research, government use and/or commercial license agreements.

This is the user's guide to CEPXS/ONELD Version 1.1, a code package for coupled electron-photon transport in one-dimensional slab geometry. The code package consists of the multigroup cross-section generating code, CEPXS; the preprocessor code, PRE1D; the discrete ordinates code, ONELD; and the postprocessor code, POST1D. In Version 1.1, new features have been implemented through several new keywords. Since Version 1.0 keywords are still applicable, this document should be considered as an addendum to the Version 1.0 User's Guide. 5 refs.

This report presents a precursory examination of a number of issues pertaining to socket contacts in hermetic connectors. The principal issues addressed are high-contact resistance and contact chatter (circuit discontinuities). Efforts examining the characteristics of the existing socket contact design, the possibility of connector/contact rework, quick-fix solutions, and contact redesigns are summarized.

A model that predicts the final velocity of high-power, pulsed-laser-driven thin flyers is described. The required input parameters can either be obtained from standard handbooks or simply extracted from one set of data. The model yields a number of features and scaling laws that are well verified by experiment. Specific comparisons of model predictions with experimental results illustrate excellent agreement for variations of laser fluence and pulse width as well as flyer diameter and thickness.

The goal of the Limited Flight Path (LFP) test series was to investigate the effect of reactor subcompartment flight path length on direct containment heating (DCH). The test series consisted of eight experiments with nominal flight paths of 1, 2, or 8 m. A thermitically generated mixture of iron, chromium, and alumina simulated the corium melt of a severe reactor accident. After thermite ignition, superheated steam forcibly ejected the molten debris into a 1:10 linear scale the model of a dry reactor cavity. The blowdown steam entrained the molten debris and dispersed it into the Surtsey vessel. The vessel pressure, gas temperature, debris temperature, hydrogen produced by steam/metal reactions, debris velocity, mass dispersed into the Surtsey vessel, and debris particle size were measured for each experiment. The measured peak pressure for each experiment was normalized by the total amount of energy introduced into the Surtsey vessel; the normalized pressures increased with lengthened flight path. The debris temperature at the cavity exit was about 2320 K. Gas grab samples indicated that steam in the cavity reacted rapidly to form hydrogen, so the driving gas was a mixture of steam and hydrogen. These experiments indicate that debris may be trapped in reactor subcompartments and thus will not efficiently transfer heat to gas in the upper dome of a containment building. The effect of deentrainment by reactor subcompartments may significantly reduce the peak containment load in a severe reactor accident. 8 refs., 49 figs., 6 tabs.

The Department of Energy's Solar Thermal Program has as one of its program elements the development and evaluation of conversion device technologies applicable to dish-electric systems. The primary research and development combines a conversion device (heat engine), solar receiver, and generator mounted at the focus of a parabolic dish concentrator. The Stirling-cycle heat engine was identified as the conversion device for dish-electric with the most potential for meeting the program's goals for efficiency, reliability, and installed cost. To advance the technology toward commercialization, Sandia National Laboratories has acquired a Stirling Thermal Motors, Inc., kinematic Stirling engine, STM4-120, for evaluation. The engine is being bench-tested at Sandia's Engine Test Facility and will be combined later with a solar receiver for on-sun evaluation. This report presents the engine characteristics, finite element analyses of critical engine components, test system layout, instrumentation, and preliminary performance results from the bench test.

The purpose of this NUREG is to present technical information that should be useful to NRC licensees in designing interior intrusion detection systems. Interior intrusion sensors are discussed according to their primary application: boundary-penetration detection, volumetric detection, and point protection. Information necessary for implementation of an effective interior intrusion detection system is presented, including principles of operation, performance characteristics and guidelines for design, procurement, installation, testing, and maintenance. A glossary of sensor data terms is included. 36 figs., 6 tabs.