Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This report describes an unpowered radio receiver capable of detecting and responding to weak signals transmit ted from comparatively long distances . This radio receiver offers key advantages over a short range zero - power radio receiver previously described in SAND2004 - 4610, A Zero - Power Radio Receiver . The device described here can be fabricated as an integrated circuit for use in portable wireless devices, as a wake - up circuit, or a s a stand - alone receiver operating in conjunction with identification decoders or other electroni cs. It builds on key sub - components developed at Sandia National Laboratories over many years. It uses surface acoustic wave (SAW) filter technology. It uses custom component design to enable the efficient use of small aperture antennas. This device uses a key component, the pyroelectric demodulator , covered by Sandia owned U.S. Patent 7397301, Pyroelectric Demodulating Detector [1] . This device is also described in Sandia owned U.S. Patent 97266446, Zero Power Receiver [2].

A power converter capable of converting the 48 V DC output of a photovoltaic panel into 120 V AC at up to 400 W has been demonstrated in a 40 cu. cm. (2.4 cu. in.) module, for a power density of greater than 160 W/cu. in. The module is enabled by the use of GaN and AlGaN field effect transistors (FETs) and diodes operating at higher power densities and higher switching frequencies than conventional silicon power devices. Typical photovoltaic panel converter/inverters have power densities ranging from 3.5-5.0 W/cu. in. and often make use of bulky, low frequency transformers. By using wide- and ultra-wide-bandgap switching devices, the operating frequency has been increased to 150 kHz, eliminating the need to use low frequency charge and current storage elements. The resulting size reduction demonstrates the significant possibilities that the adoption of GaN and AlGaN devices housed in small, 3D printed packages offers in the field of power electronics.

Abstract not provided.

Abstract not provided.

The effects of paralleling low-current vertical Gallium Nitride (v-GaN) diodes in a custom power module are reported. Four paralleled v-GaN diodes were demonstrated to operate in a buck converter at 1.3 Apeak (792 mArms) at 240 V and 15 kHz switching frequency. Additionally, high-fidelity SPICE simulations demonstrate the effects of device parameter variation on power sharing in a power module. The device parameters studied were found to have a sub-linear relationship with power sharing, indicating a relaxed need to bin parts for paralleling. This result is very encouraging for power electronics based on low-current v-GaN and demonstrates its potential for use in high-power systems.

Abstract not provided.

Abstract not provided.

This report describes an active radiation test of 28 optocouplers (19 different devices) conducted at the Sandia National Laboratories (SNL) Annular Core Research Reactor (ACRR). The optocouplers consisted of commercially available components in one of three different package configurations: (1) commercially available as a single, sealed component, (2) commercially available as two sealed components that were aligned with external fixturing, and (3) commercially available as die that were packaged into a single, sealed component.

Abstract not provided.

Surface acoustic wave (SAW) devices are used as sensing elements in the best performing portable chemical detectors. The SAW device, with a selectively absorbing chemical coating, serves as a mass sensor which preferentially responds to various chemical exposures. To obtain the highest performance, a number of criteria must be optimized, including SAW microwave insertion loss, impedance matching, electrode design configuration, RF shielding, chemically absorbent coating area, electronic measurement approach, and microfluidic packaging. A properly optimized system can be sensitive to chemical exposures the parts-per-trillion range. We report on a design optimization approach consisting of multiple comparison experiments made with competing designs. © 2012 IEEE.

Abstract not provided.

Abstract not provided.

The National Ecological Observatory Network (NEON) is an ambitious National Science Foundation sponsored project intended to accumulate and disseminate ecologically informative sensor data from sites among 20 distinct biomes found within the United States and Puerto Rico over a period of at least 30 years. These data are expected to provide valuable insights into the ecological impacts of climate change, land-use change, and invasive species in these various biomes, and thereby provide a scientific foundation for the decisions of future national, regional, and local policy makers. NEON's objectives are of substantial national and international importance, yet they must be achieved with limited resources. Sandia National Laboratories was therefore contracted to examine four areas of significant systems engineering concern; specifically, alternatives to commercial electrical utility power for remote operations, approaches to data acquisition and local data handling, protocols for secure long-distance data transmission, and processes and procedures for the introduction of new instruments and continuous improvement of the sensor network. The results of these preliminary systems engineering evaluations are presented, with a series of recommendations intended to optimize the efficiency and probability of long-term success for the NEON enterprise.

Abstract not provided.

This report gives a description of the development of a Stable Local Oscillator (StaLO) multi-chip module (MCM). It is a follow-on report to SAND2006-6414, Stable Local Oscillator Microcircuit. The StaLO accepts a 100MHz input signal and produces output signals at 1.2, 3.3, and 3.6 GHz. The circuit is built as a multi-chip module (MCM), since it makes use of integrated circuit technologies in silicon and lithium niobate as well as discrete passive components. This report describes the development of an MCM-based version of the complete StaLO, fabricated on an alumina thick film hybrid substrate.

This report gives a description of the development of a Delay Locked Loop (DLL) integrated circuit (IC). The DLL was developed and tested as a stand-alone IC test chip to be integrated into a larger application specific integrated circuit (ASIC), the Quadrature Digital Waveform Synthesizer (QDWS). The purpose of the DLL is to provide a digitally programmable delay to enable synchronization between an internal system clock and external peripherals with unknown clock skew. The DLL was designed and fabricated in the IBM 8RF process, a 0.13 {micro}m CMOS process. It was designed to operate with a 300MHz clock and has been tested up to 500MHz.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.