Radiation-hard high-voltage vertical GaN p-n diodes are being developed for use in power electronics subjected to ionizing radiation. We present a comparison of the measured and simulated photocurrent response of diodes exposed to ionizing irradiation with 70 keV and 20 MeV electrons at dose rates in the range of 1.4× 107 - 5.0× 108 rad(GaN)/s. The simulations correctly predict the trend in the measured steady-state photocurrent and agree with the experimental results within a factor of 2. Furthermore, simulations of the transient photocurrent response to dose rates with uniform and non-uniform ionization depth profiles uncover the physical processes involved that cannot be otherwise experimentally observed due to orders of magnitude larger RC time constant of the test circuit. The simulations were performed using an eXploratory Physics Development code developed at Sandia National Laboratories. The code offers the capability to include defect physics under more general conditions, not included in commercially available software packages, extending the applicability of the simulations to different types of radiation environments.
Vertical gallium nitride (GaN) p-n diodes have garnered significant interest for use in power electronics where high-voltage blocking and high-power efficiency are of concern. In this article, we detail the growth and fabrication methods used to develop a large area (1 mm2) vertical GaN p-n diode capable of a 6.0-kV breakdown. We also demonstrate a large area diode with a forward pulsed current of 3.5 A, an 8.3-mΩ·cm2 differential specific ON-resistance, and a 5.3-kV reverse breakdown. In addition, we report on a smaller area diode (0.063 mm2) that is capable of 6.4-kV breakdown with a differential specific ON-resistance of 10.2 m·Ω·cm2, when accounting for current spreading through the drift region at a 45° angle. Finally, the demonstration of avalanche breakdown is shown for a 0.063-mm2 diode with a room temperature breakdown of 5.6 kV. These results were achieved via epitaxial growth of a 50-μm drift region with a very low carrier concentration of < 1×1015 cm-3 and a carefully designed four-zone junction termination extension.
Impact ionization coefficients play a critical role in semiconductors. In addition to silicon, silicon carbide and gallium nitride are important semiconductors that are being seen more as mainstream semiconductor technologies. As a reflection of the maturity of these semiconductors, predictive modeling has become essential to device and circuit designers, and impact ionization coefficients play a key role here. Recently, several studies have measured impact ionization coefficients. We dedicated the first part of our study to comparing three experimental methods to estimate impact ionization coefficients in GaN, which are all based on photomultiplication but feature characteristic differences. The first method inserts an InGaN hole-injection layer, the accuracy of which is challenged by the dominance of ionization in InGaN, leading to possible overestimation of the coefficients. The second method utilizes the Franz-Keldysh effect for hole injection but not for electrons, where the mixed injection of induced carriers would require a margin of error. The third method uses complementary p-n and n-p structures that have been at the basis of this estimation in Si and SiC and leans on the assumption of a constant electric field, and any deviation would require a margin of error. In the second part of our study, we evaluated the models using recent experimental data from diodes demonstrating avalanche breakdown.
The controlled fabrication of vertical, tapered, and high-aspect ratio GaN nanowires via a two-step top-down process consisting of an inductively coupled plasma reactive ion etch followed by a hot, 85% H3PO4 crystallographic wet etch is explored. The vertical nanowires are oriented in the [0001] direction and are bound by sidewalls comprising of 3362 ¯ } semipolar planes which are at a 12° angle from the [0001] axis. High temperature H3PO4 etching between 60 °C and 95 °C result in smooth semipolar faceting with no visible micro-faceting, whereas a 50 °C etch reveals a micro-faceted etch evolution. High-angle annular dark-field scanning transmission electron microscopy imaging confirms nanowire tip dimensions down to 8–12 nanometers. The activation energy associated with the etch process is 0.90 ± 0.09 eV, which is consistent with a reaction-rate limited dissolution process. The exposure of the 3362 ¯ } type planes is consistent with etching barrier index calculations. The field emission properties of the nanowires were investigated via a nanoprobe in a scanning electron microscope as well as by a vacuum field emission electron microscope. The measurements show a gap size dependent turn-on voltage, with a maximum current of 33 nA and turn-on field of 1.92 V nm−1 for a 50 nm gap, and uniform emission across the array.
This work investigates both avalanche behavior and failure mechanism of 3 kV GaN-on-GaN vertical P-N diodes, that were fabricated and later tested under unclamped inductive switching (UIS) stress. The goal of this study is to use the particular avalanche characteristics and the failure mechanism to identify issues with the field termination and then provide feedback to improve the device design. DC breakdown is measured at the different temperatures to confirm the avalanche breakdown. Diode's avalanche robustness is measured on-wafer using a UIS test set-up which was integrated with a wafer chuck and CCD camera. Post failure analysis of the diode is done using SEM and optical microscopy to gain insight into the device failure physics.
The III-nitride semiconductors are attractive for on-chip, solid-state vacuum nanoelectronics, having high thermal and chemical stability, low electron affinity, and high breakdown fields. Here we report top-down fabricated, lateral gallium nitride (GaN)-based nanoscale vacuum electron diodes operable in air, with ultra-low turn-on voltages down to ~0.24 V, and stable high field emission currents, tested up to several microamps for single-emitter devices. We present gap-size and pressure dependent studies which provide insights into the design of future nanogap vacuum electron devices. The vacuum nanodiodes also show high resistance to damage from 2.5 MeV proton exposure. Preliminary results on the fabrication and characteristics of lateral GaN nano vacuum transistors will also be presented. The results show promise for a new class of robust, integrated, III-nitride based vacuum nanoelectronics.
Ultra-low voltage drop tunnel junctions (TJs) were utilized to enable multi-active region blue light emitting diodes (LEDs) with up to three active regions in a single device. The multi-active region blue LEDs were grown monolithically by metal-organic chemical vapor deposition (MOCVD) without growth interruption. This is the first demonstration of a MOCVD grown triple-junction LED. Optimized TJ design enabled near-ideal voltage and EQE scaling close to the number of junctions. This work demonstrates that with proper TJ design, improvements in wall-plug efficiency at high output power operation are possible by cascading multiple III-nitride based LEDs.
We present progress on the synthesis of semimetal Cd3As2 by metal–organic chemical-vapor deposition (MOCVD). Specifically, we have optimized the growth conditions needed to obtain technologically useful growth rates and acceptable thin-film microstructures, with our studies evaluating the effects of varying the temperature, pressure, and carrier-gas type for MOCVD of Cd3As2 when performed using dimethylcadmium and tertiary-butylarsine precursors. In the course of the optimization studies, exploratory Cd3As2 growths are attempted on GaSb substrates, strain-relaxed InAs buffer layers grown on GaSb substrates, and InAs substrates. Notably, only the InAs-terminated substrate surfaces yield desirable results. Extensive microstructural studies of Cd3As2 thin films on InAs are performed by using multiple advanced imaging microscopies and x-ray diffraction modalities. The studied films are 5–75 nm in thickness and consist of oriented, coalesced polycrystals with lateral domain widths of 30–80 nm. The most optimized films are smooth and specular, exhibiting a surface roughness as low as 1.0 nm rms. Under cross-sectional imaging, the Cd3As2-InAs heterointerface appears smooth and abrupt at a lower film thickness, ~30 nm, but becomes quite irregular as the average thickness increases to ~55 nm. The films are strain-relaxed with a residual biaxial tensile strain (ϵxx = +0.0010) that opposes the initially compressive lattice-mismatch strain of Cd3As2 coherent on InAs (ϵxx = - 0.042). Importantly, phase-identification studies find a thin-film crystal structure consistent with the P42/nbc space group, placing MOCVD-grown Cd3As2 among the Dirac semimetals of substantial interest for topological quantum materials studies.
We carefully investigate three important effects including postgrowth activation annealing, delta (δ) dose and magnesium (Mg) buildup delay as well as experimentally demonstrate their influence on the electrical properties of GaN homojunction p–n diodes with a tunnel junction (TJ). The diodes were monolithically grown by metalorganic chemical vapor deposition (MOCVD) in a single growth step. By optimizing the annealing parameters for Mg activation, δ-dose for both donors and acceptors at TJ interfaces, and p+-GaN layer thickness, a significant improvement in tunneling properties is achieved. For the TJs embedded within the continuously-grown, all-MOCVD GaN diode structures, ultra-low voltage penalties of 158 mV and 490 mV are obtained at current densities of 20 A cm−2 and 100 A cm−2, respectively. The diodes with the engineered TJs show a record-low differential resistivity of 1.6 × 10−4 Ω cm2 at 5 kA cm−2.
The III-nitride semiconductors have many attractive properties for field-emission vacuum electronics, including high thermal and chemical stability, low electron affinity, and high breakdown fields. Here, we report top-down fabricated gallium nitride (GaN)-based nanoscale vacuum electron diodes operable in air, with record ultralow turn-on voltages down to ∼0.24 V and stable high field-emission currents, tested up to several microamps for single-emitter devices. We leverage a scalable, top-down GaN nanofabrication method leading to damage-free and smooth surfaces. Gap-dependent and pressure-dependent studies provide new insights into the design of future, integrated nanogap vacuum electron devices. The results show promise for a new class of high-performance and robust, on-chip, III-nitride-based vacuum nanoelectronics operable in air or reduced vacuum.