The understanding and control of charge carrier interactions with defects at buried insulator/semiconductor interfaces is essential for achieving optimum performance in modern electronics. Here, we report on the use of scanning ultrafast electron microscopy (SUEM) to remotely probe the dynamics of excited carriers at a Si surface buried below a thick thermal oxide. Our measurements illustrate a previously unidentified SUEM contrast mechanism, whereby optical modulation of the space-charge field in the semiconductor modulates the electric field in the thick oxide, thus affecting its secondary electron yield. By analyzing the SUEM contrast as a function of time and laser fluence we demonstrate the diffusion mediated capture of excited carriers by interfacial traps.
In preparation for testing a lithium-helium heat exchanger at Sandia, unexpected rapid failure of the mild steel lithium preheater due to liquid metal embrittlement occurred when lithium at ~400 °C flowed into the preheater then at ~200 °C. This happened before the helium system was pressurized or heating with electron beams began. The paper presents an analysis of the preheater plus a discussion of some implications for fusion.
This LDRD supported efforts to significantly advance the scanning ultrafast electron microscope (SUEM) for spatial-temporal mapping of charge carrier dynamics in semiconductor materials and microelectronic devices. Sandia's SUEM capability in Livermore, CA, was built and demonstrated with previous LDRD funding; however, the stability and usability of the tool limited the throughput for analyzing samples. A new laser alignment strategy improved the stability of the SUEM, and the design and characterization of a new micro-channel plate (MCP)- based detector improved the signal-to-noise of the SUEM signal detection. These enhancements to the SUEM system improved throughput by over two orders of magnitude (before, a single time series of SUEM measurements would take several days to several weeks to acquire; now, the same measurements can be completed in~90 minutes in an automated fashion). The SUEM system can now be routinely used as an analytical instrument and will be a central part of several multi-year projects starting in FY22.
This project aimed to identify the performance-limiting mechanisms in mid- to far infrared (IR) sensors by probing photogenerated free carrier dynamics in model detector materials using scanning ultrafast electron microscopy (SUEM). SUEM is a recently developed method based on using ultrafast electron pulses in combination with optical excitations in a pump- probe configuration to examine charge dynamics with high spatial and temporal resolution and without the need for microfabrication. Five material systems were examined using SUEM in this project: polycrystalline lead zirconium titanate (a pyroelectric), polycrystalline vanadium dioxide (a bolometric material), GaAs (near IR), InAs (mid IR), and Si/SiO 2 system as a prototypical system for interface charge dynamics. The report provides detailed results for the Si/SiO 2 and the lead zirconium titanate systems.
The surfaces of textured polycrystalline N-type bismuth telluride and P-type antimony telluride materials were investigated using ex situ photoelectron emission microscopy (PEEM). PEEM enabled imaging of the work function for different oxidation times due to exposure to air across sample surfaces. The spatially averaged work function was also tracked as a function of air exposure time. N-type bismuth telluride showed an increase in the work function around grain boundaries relative to grain interiors during the early stages of air exposure-driven oxidation. At longer time exposure to air, the surface became homogenous after a ∼5 nm-thick oxide formed. X-ray photoemission spectroscopy was used to correlate changes in PEEM imaging in real space and work function evolution to the progressive growth of an oxide layer. The observed work function contrast is consistent with the pinning of electronic surface states due to the defects at a grain boundary.
Multiple experimental configurations for performing nanoscale orientation mapping are compared to determine their fidelity to the true microstructure of a sample. Transmission Kikuchi diffraction (TKD) experiments in a scanning electron microscope (SEM) and nanobeam diffraction (NBD) experiments in a transmission electron microscope (TEM) were performed on thin electrodeposited hard Au films with two different microstructures. The Au samples either had a grain size that is >50 or <20 nm. The same regions of the samples were measured with TKD apparatuses at 30 kV in an SEM with detectors in the horizontal and vertical configurations and in the TEM at 300 kV. Under the proper conditions, we demonstrate that all three configurations can produce data of equivalent quality. Each method has strengths and challenges associated with its application and representation of the true microstructure. The conditions needed to obtain high-quality data for each acquisition method and the challenges associated with each are discussed.
The high-cycle fatigue life of nanocrystalline and ultrafine-grained Ni-Fe was examined for five distinct grain sizes ranging from approximately 50–600 nm. The fatigue properties were strongly dependent on grain size, with the endurance limit changing by a factor of 4 over this narrow range of grain size. The dataset suggests a breakdown in fatigue improvement for the smallest grain sizes <100 nm, likely associated with a transition to grain coarsening as a dominant rate-limiting mechanism. The dataset also is used to explore fatigue prediction from monotonic tensile properties, suggesting that a characteristic flow strength is more meaningful than the widely-utilized ultimate tensile strength.
Equal channel angular extrusion (ECAE) of 49Fe-49Co-2V, also known as Hiperco® 50A or Permendur-2V, greatly improves the strength and ductility of this alloy, while sacrificing soft magnetic performance. In this work, ECAE Hiperco specimens were subjected to post-ECAE annealing in order to improve soft magnetic properties. The microstructure, mechanical properties, and magnetic performance are summarized in this study. Annealing begins above 650°C and a steep decline in yield strength is observed for heat treatments between 700 and 840°C due to grain growth and the Hall-Petch effect, although some strength benefit is still observed in fully annealed ECAE material compared to conventionally processed bar. Soft magnetic properties were assessed through B-H hysteresis curves from which coercivity (Hc) values were extracted. Hc decreases rapidly with annealing above 650°C as well, i.e. improved soft magnetic behavior. The observed trend is attributed to annealing and grain growth in this temperature regime, which facilitates magnetic domain wall movement. The coercivity vs. grain size results generally follow the trend predicted in the literature. The magnetic behavior of annealed ECAE material compares favorably to conventional bar, possibly due to mild crystallographic texturing which enhances properties in the post-ECAE annealed material. Overall, this study highlights a definitive tradeoff between mechanical and magnetic properties brought about by post-ECAE annealing and grain growth.
HfC has shown promise as a material for field emission due to the low work function of the (100) surface and a high melting point. Recently, HfC tips have exhibited unexpected failure after field emission at 2200 K. Characterization of the HfC tips identified faceting of the parabolic tip dominated by coexisting (100) and (111) surfaces. To investigate this phenomenon, we used density functional theory (DFT) simulations to identify the role of defects and impurities (Ta, N, O) on HfC surface properties. Carbon vacancies increased the surface energy of the (100) surface from 2.35 J/m2 to 4.75 J/m2 and decreased the surface energy of the carbon terminated (111) surface from 8.75 J/m2 to 3.48 J/m2. Once 60% of the carbon on the (100) surface have been removed the hafnium terminated (111) surface becomes the lowest energy surface, suggesting that carbon depletion may cause these surfaces to coexist. The addition of Ta and N impurities to the surface are energetically favorable and decrease the work function, making them candidate impurities for improving field emission at high temperatures. Overall, DFT simulations have demonstrated the importance of understanding the role of defects on the surface structure and properties of HfC.
Intermetallic alloys possess exceptional soft magnetic properties, including high permeability, low coercivity, and high saturation induction, but exhibit poor mechanical properties that make them impractical to bulk process and use at ideal compositions. We used laser-based Additive Manufacturing to process traditionally brittle Fe–Co and Fe–Si alloys in bulk form without macroscopic defects and at near-ideal compositions for electromagnetic applications. The binary Fe–50Co, as a model material, demonstrated simultaneous high strength (600–700 MPa) and high ductility (35%) in tension, corresponding to a ∼300% increase in strength and an order-of-magnitude improvement in ductility relative to conventionally processed material. Atomic-scale toughening and strengthening mechanisms, based on engineered multiscale microstructures, are proposed to explain the unusual combination of mechanical properties. This work presents an instance in which metal Additive Manufacturing processes are enabling, rather than limiting, the development of higher-performance alloys.
This study investigates the mechanical and corrosion properties of as-built and annealed equiatomic CoCrFeMnNi alloy produced by laser-based directed energy deposition (DED) Additive Manufacturing (AM). The high cooling rates of DED produced a single-phase, cellular microstructure with cells on the order of 4 μm in diameter and inter-cellular regions that were enriched in Mn and Ni. Annealing created a chemically homogeneous recrystallized microstructure with a high density of annealing twins. The average yield strength of the as-built condition was 424 MPa and exceeded the annealed condition (232 MPa), however; the strain hardening rate was lower for the as-built material stemming from higher dislocation density associated with DED parts and the fine cell size. In general, the yield strength, ultimate tensile strength, and elongation-to-failure for the as-built material exceeded values from previous studies that explored other AM techniques to produce the CoCrFeMnNi alloy. Ductile fracture occurred for all specimens with dimple initiation associated with nanoscale oxide inclusions. The breakdown potential (onset of pitting corrosion) was similar for the as-built and annealed conditions at 0.40 VAg/AgCl when immersed in 0.6 M NaCl. Pit morphology/propagation for the as-built condition exhibited preferential corrosion of inter-cellular Ni/Mn regions leading to a tortuous pit bottom and cover, while the annealed conditions pits resembled lacy pits similar to 304 L steel. A passive oxide film depleted in Cr cations with substantial incorporation of Mn cations is proposed as the primary mechanism for local corrosion susceptibility of the CoCrFeMnNi alloy.
Control of the atomic structure, as measured by the extent of the embrittling B2 chemically ordered phase, is demonstrated in intermetallic alloys through additive manufacturing (AM) and characterized using high fidelity neutron diffraction. As a layer-by-layer rapid solidification process, AM was employed to suppress the extent of chemically ordered B2 phases in a soft ferromagnetic Fe-Co alloy, as a model material system of interest to electromagnetic applications. The extent of atomic ordering was found to be insensitive to the spatial location within specimens and suggests that the thermal conditions within only a few AM layers were most influential in controlling the microstructure, in agreement with the predictions from a thermal model for welding. Analysis of process parameter effects on ordering found that suppression of B2 phase was the result of an increased average cooling rate during processing. AM processing parameters, namely interlayer interval time and build velocity, were used to systematically control the relative fraction of ordered B2 phase in specimens from 0.49 to 0.72. Hardness of AM specimens was more than 150% higher than conventionally processed bulk material. Implications for tailoring microstructures of intermetallic alloys are discussed.
In Part I, equal channel angular extrusion (ECAE) was demonstrated as a novel, simple-shear deformation process for producing bulk forms of the low ductility Fe-Co-2V (Hiperco 50A®) soft ferromagnetic alloy with refined grain sizes. Microstructures and mechanical properties were discussed. In this Part II contribution, the crystallographic textures and quasi-static magnetic properties of ECAE-processed Hiperco were characterized. The textures were of a simple-shear character defined by partial {110} and (111) fibers inclined relative to the extrusion direction, in agreement with the expectations for simple-shear deformation textures of BCC metals. These textures were observed throughout all processing conditions and only slightly reduced in intensity by subsequent recrystallization heat treatments. Characterization of the magnetic properties revealed a lower coercivity and higher permeability for ECAE-processed Hiperco specimens relative to the conventionally processed and annealed Hiperco bar. The effects of the resultant microstructure and texture on the coercivity and permeability magnetic properties are discussed.