Publications

We have completed an experimental study to investigate the use of infrared emission spectroscopy (IRES) for the quantitative analysis of borophosphosilicate glass (BPSG) thin films on silicon monitor wafers. Experimental parameters investigated included temperatures within the range used in the microelectronics industry to produce these films; hence the potential for using the IRES technique for real-time monitoring of the film deposition process has been evaluated. The film properties that were investigated included boron content, phosphorus content, film thickness, and film temperature. The studies were conducted over two temperature ranges, 125 to 225 *C and 300 to 400 *C. The later temperature range includes realistic processing temperatures for the chemical vapor deposition (CVD) of the BPSG films. Partial least squares (PLS) multivariate calibration methods were applied to spectral and film property calibration data. The cross-validated standard errors of prediction (CVSEP) fi-om the PLS analysis of the IRES spectraof21 calibration samples each measured at 6 temperatures in the 300 to 400 "C range were found to be 0.09 wt. `?40 for B, 0.08 wt. `%0 for P, 3.6 ~m for film thickness, and 1.9 *C for temperature. By lowering the spectral resolution fi-om 4 to 32 cm-l and decreasing the number of spectral scans fi-om 128 to 1, we were able to determine that all the film properties could be measured in less than one second to the precision required for the manufacture and quality control of integrated circuits. Thus, real-time in-situ monitoring of BPSG thin films formed by CVD deposition on Si monitor wafers is possible with the methods reported here.

GaAs-based metal semiconductor field effect transistors (MESFETS), heterojunction bipolar transistors (HBTs) and high electron mobility transistors (HEMTs) have been exposed to ECR SiJ&/NH3 discharges for deposition of SiNX passivating layers. The effect of source power, rf chuck power, pressure and plasma composition have been investigated. Effects due to both ion damage and hydrogenation of dopants are observed. For both HEMTs and MESFETS there are no conditions where substantial increases in channel sheet resistivity are not observed, due primarily to (Si-H)O complex formation. In HBTs the carbon-doped base layer is the most susceptible layer to hydrogenation. Ion damage in all three devices is minimized at low rf chuck power, moderate ECR source power and high deposition rates.

The conceptual and computational structure of a performance assessment (PA) for the Waste Isolation Pilot Plant (WIPP) is described. Important parts of thk structure are @ maintenance of a separation between stochastic (i.e., aleatory) and subjective (i.e., epistemic) uncertain, with stochastic uncefinty arising from the many possible disruptions that could occur over the 10,000 Y regulatory period fiat applies to the WIPP and subjective uncertainty arising from `the imprecision with which many of the quantities rquired in tie `hdysis are known, (ii) use of Latin hypercttbe sampling to incorporate the effects of subjective uncefirtty, (iii) use of Monte Carlo (i.e., random) sampling to incorporate the effects of stochastic uncetinty, and OV) efficient use of tie necessarily limited number of mechanistic calculations that can be performed to SUPPOII the analysis. The WIPP is under development by the U.S. Department of Ener~ (DOE) for the geologic (i.e., deep underground) disposal of transuranic (TRU) waste, with the indicated PA supporting a ~Compliance Certification Application (CCA) by the DOE to the U.S. Environmental Protection Agency (EPA) in October 1996 for tie necessary certifications for the WIPP to begin operation. If certified, the WIPP will be the first operational faciliv in tie United States for the geologic disposal of ra&oactive waste.

Recent interest in the detection and analysis of biological samples by spectroscopic methods has led to questions concerning the degree of distinguishability and biological variability of the ultraviolet (W) fluorescent spectra from such complex samples. We show that the degree of distinguishability of such spectra is readily determined numerically.

The evolution of stress in gallium nitride films on sapphire has been measured in real- time during metal organic chemical vapor deposition. In spite of the 161%0 compressive lattice mismatch of GaN to sapphire, we find that GaN consistently grows in tension at 1050"C. Furthermore, in-situ stress monitoring indicates that there is no measurable relaxation of the tensile growth stress during annealing or thermal cycling.

Plasma processing of microelectronic materials is strongly dependent on the generation and control of neutral radial and ion species generated in a plasma. For example, process uniformity across a #er is drken by a combination of plasma charged particle and neutral uniformity. Due to extensive rexarch and engineering the current generation of commercial plasma reactors can generate very radially uniform ion distributions, usually better than ~ 2 perwnt as determined by ion saturation measurements. Due in part to the difficulty associated with determining the neutral radial distributions, control of the neutral radical uniformity is less well developed. This abstract will review our recent measurements of the spatial distribution of severaI important atomic and molecukw species in inductively coupled plasmas through C12 / BCIJ / Ar containing gas mixtures. Measured species include the ground state Cl and BC1 densities as well as the metastable argon density. The fbeus of this review will be on the experimental techniques and results. In addition to assisting in the development of a fbndarnental understanding of the important pkunna physics, these measurements have been used to benchmark multi dimensional plasma discharge codes.

Cerrusite (PbC03) is soluble under acidic conditions and considered to be a highly bioavailable soil Pb species. In this study, synthetic cerrusite and hydroxyapatite [Ca5(P04)30H] were reacted under constant and dynamic pH conditions with various P/Pb molar ratios in an attempt to evaluate the effect of reaction kinetics on the formation of chloropyromorphite (Pb5(P04)3Cl) and solubilization of Pb. Under constant pH conditions, dissolution rates of both cerrusite and apatite were rapid when pH was low. Complete conversion of Pb from cerrusite to chloropyromorphite occurred within 60 tin at pH 4 and below when the amount of phosphate in the added apatite was stoichoimetrically equal to that needed to transform all added Pb into chloropyromorphite. The concentration of soluble Pb depended upon the volubility of chloropyromorphite. The dissolution rates of apatite and cerrusite decreased with increasing pH, and the transformation was incomplete at pH 5 and above in the 60 rnin reaction period. The soluble Pb level, therefore, was determined by the volubility of cerrusite. In the dynamic pH system which simulated the gastrointestinal tract (GI tract) system, a complete transformation of Pb from cerrusite to chloropyromorphite was achieved due to the complete dissolution of apatite and cerrusite at the initial low pHs. Chloropyromorphite was the exclusive reaction product in both constant and dynamic pH systems as indicated by XRD analysis. The differences in transformation rate and the control of Pb volubility between the reactions occurring in constant and dynamic pH systems indicate the significance of kinetics in controlling the bioavailability of Pb and the potential for the reaction to occur during ingestion.

Transformation of unstable lead [Pb(ll)] forms into insoluble pyromorphite, [Pb5(P04)3(OH, Cl, F...)], by addition of phosphate to Pb contaminated soil has been proposed as a remediation technology which reduces the mobility and bioavailability of Pb. Under aerobic condition, oxidation of dissolved sulfide increases dissolution of galena (PbS), causing it to become a source of liable Pb forms in soils, sediments and wastes. Thus, a galena ore was reacted with synthetic hydroxyapatite [Ca5(P04)30H] under various pH condition to determine the formation rate of pyromorphite and the volubility of galena under the ambient conditions. In a 6 day reaction period the dissolution rate of galena increased with pH due to the oxidation of dissolved sulfide. Correspondingly, formation of chloropyrornorphite became apparent in the galena- apatite suspensions with increasing pH. The insignificant effect of mineral P/Pb molar ratio on the formation of chloropyromorphite implied that dissolution of galena was the rate limiting step.

The Sandia Z machine is a source of intense radiation which can be used to drive ablative shocks for equation of state studies. In developing the capability to diagnose these types of studies on Z, techniques commonly used in conventional impact generated experiments were leveraged. The primary diagnostic transferred was velocity interferome~, VLSAR, [1] which not only provides Hugoniot particle velocity measurements, but also indications of shock stability and wave attenuation. In addition to a VISAR capability on the Z machine, methods for measuring shock velocity have been developed. When these measured parameters are used in conjunction with the Rankine-Hugoniot jump conditions, [2] material response at high temperatures and pressures can be inferred. With sample sizes used on Z being much smaller than those fielded in typical impact experiments, temporal resolution and methods of interfacing the diagnostics with the targets had to be improved. In this paper, a "standard" equation of state experiment, associated diagnostics, and some recent results in aluminum and beryllium will be discussed.

The recent development of Z pinch drivers for producing intense radiation envkomn~ enables study of physical and mechanical properties of condensed materials in regimes previously inaccessible in the Mm-am-y. With Z pinch radiation sources, it is possible fo subject mm-sized sampies to pianar compressions of a fe w Mbar. Tie-resolved velocity interferometry was used to perform the first shock loading and unloading profiles in Al and Be for ablatively driven shock$s to 3 Mbar and the first iseritropic loading of iron specimens to 300 War. A principai goai of our shock physics program is to establish a capability to make accurats eqwion of state measurements on the Z pulsed radiation source. The Z accelerator is a source of intense radntion, which can be used to drive ablative shocks for E(X$ studies. With this source, ablative muki-Mbar shocks can be produced to study materials over the range of interest to both weapons and ICF physics programs. In developing the capability to diagnose these types of studies on Z, techniques commonly used in conventional impact generated experiments were implemented. The primary diagnostic presently being used for this work is ve"!ocity interferoinetry, VL%4R, [2] which not only provides Hugoniot particle velocity measurements, but also measurements of non-shock EOS measummenu,, such as isentropic compression. In addition to VKSAR capability, methods for measuring shock velocity have also been developed for shock studies on Z. When used in conjunction with the Rankine-Hugoniot jump conditions, material response at high temperatures and pressures can be inferred. The next section discusses the basic approach for conducting EOS experiments on Z for both shock loading and istmtropic compression on the Z accelerator.

We have employed Langmuir monolayer of highly asymmetric polydimethylsiloxane- polystyrene (PDMS-PS) diblock copolymers on dioctyl phthalate (DOP) at temperatures ranging from 22 "C to -35 `C as a model system for tethered chains in poor solvent conditions. The thicknesses of the tethered PS layers extending into the DOP subphase, measured by neutron reflection, decrease with decreasing temperature (T) over this entire r~ge. However, the v~iation with T becomes weak below -20 "C. At the ]owest T, the layer thicknesses are contracted 55 % -75 `% of their values at the theta condition (T8 = 22 "C), but are still quite swollen compared to the fully collapsed, nonsolvent limit. The contraction of the layer with decreasing T is determined as a function of surface density and molecular weight. These data are compared to universal scaling forms. The PS segments are depleted from the air surface over the entire T range, the thickness of the depletion layer increasing slightly with decreasing T. The free energy of the surface layer is probed by surface tension measurements. Negative surface pressures are observed at low coverages for both PDMS-PS and PDMS monolayer, indicating metastability toward lateral phase separation. Evidence for a trruisition from a dispersed phase to a condensed phase with decreasing T was observed in the reflectivity at very low PDMS-PS coverage.

W and WSi ohmic contacts on both p- and n-type GaN have been annealed at temperatures from 300-1000 *C. There is minimal reaction (< 100 ~ broadening of the metal/GaN interface) even at 1000 *C. Specific contact resistances in the 10-5 f2-cm2 range are obtained for WSiX on Si-implanted GaN with a peak doping concentration of- 5 x 1020 cm-3, after annealing at 950 `C. On p-GaN, leaky Schottky diode behavior is observed for W, WSiX and Ni/Au contacts at room temperature, but true ohmic characteristics are obtained at 250 - 300 *C, where the specific contact resistances are typically in the 10-2 K2-cm2 range. The best contacts for W and WSiX are obtained after 700 *C annealing for periods of 30- 120 sees. The formation of &WzN interracial phases appear to be important in determining the contact quality.

Abstract not provided.

The basic mechanisms of single-event upset are reviewed, including charge collection in silicon junctions and transistors, and properties of single-event upset in CMOS static random access memory (SRAM) cells. The mechanisms are illustrated through the use of three-dimensional device and circuit simulations. Technology trends and implications for commercial devices are discussed.

Highly-oriented, multi-walled carbon nanotubes were grown on polished polycrystalline and single crystal nickel substrates by plasma enhanced hot filament chemical vapor deposition at temperatures below 666"C. The carbon nanotubes range from 10 to 500 nm in diameter and 0.1 to 50 pm in length depending on growth conditions. Acetylene is used as the carbon source for the growth of the carbon nanotubes and ammonia is used for dilution gas and catalysis. The plasma intensity, acetylene to ammonia gas ratio and their flow rates, etc. affect the diameters and uniformity of the carbon nanotubes. In summary, we synthesized large-area highly-oriented carbon nanotubes at temperatures below 666C by plasma-enhanced hot filament chemical vapor deposition. Acetylene gas is used to provide carbon for nanotube growth and ammonia gas is used for dilution and catalysis. Plasma intensity is critical in determining the nanotube aspect ratios (diameter and length), and range of both site and height distributions within a given film.

Integrated electroceramic thin film devices on semiconductor and insulator substrates feature a variety of attractive attributes, including high capacitance density, nonvolatile memory, sensor/actuator ability, and other unique electronic and optical properties. The ability to pattern such ceramic materials atop semiconductor substrates, thus, is a critical technology. Patterned oxide thin film devices are typically formed by uniform film deposition followed by somewhat complicated post-deposition ion-beam or chemical etching in a controlled environment. We review here the development of an ambient atmosphere technique which allows selective deposition of electroceramic thin layers without such post-deposition etching. In this method, substrate surfaces are selectively functionalized with hydrophobic self-assembled monolayer to modify the adhesion of subsequently deposited solution-derived electroceramics. The selective fictionalization is achieved through microcontact printing (v-CP) of self-assembled monolayer of the chemical octadecyltrichlorosilane on substrates of technical interest. Subsequent sol-gel deposition of ceramic oxides on these functionalized substrates, followed by lift-off from the monolayer, yields high quality, patterned oxide thin layers only on the unfunctionalized regions. A variety of micron- scale dielectric oxide devices have been fabricated using this process, with lateral resolution as fine as 0.5Lm. In this paper, we review the monolayer patterning and electrical behavior of several patterned electroceramic thin films, including Pb(Zr,Ti)03 [PZT], LiNb03, and Ta205. An applied device example is also presented in combination with selective MOCVD deposition of metal electrodes: integrated, fully monolayer-patterned Pt//PZT//PSi(Si(100) ferroelectric memory cells.

Seven holes were drilled and wells (H-19b0, H-19b2, H-19b3, H-19b4, H-19b5, H-19b6, and H-19b7) were constructed on the H-19 hydropad to conduct field activities in support of the Culebra Transport Program. These wells were drilled and completed on the Waste Isolation Pilot Plant (WIPP) site during February to September 1995. An eighth hole, H-19b1, was drilled but had to be abandoned before the target depth was reached because of adverse hole conditions. The geologic units penetrated at the H-19 location include surficial deposits of Holocene age, rocks from the Dockum Group of Upper Triassic age, the Dewey Lake Redbeds, and Rustler Formation of the Permian age. The Rustler Formation has been further divided into five informal members which include the Forty-niner Member, Magenta Member, Tamarisk Member, Culebra Dolomite Member, and an unnamed lower member. The Rustler Formation, particularly the Culebra Dolomite Member, is considered critical for hydrologic site characterization. The Culebra is the most transmissive saturated unit above the WIPP repository and, as such, is considered to be the most likely pathway for radionuclide transport to the accessible environment in the unlikely event the repository is breached. Seven cores from the Culebra were recovered during drilling activities at the H-19 hydropad and detailed descriptions of these cores were made. On the basis of geologic descriptions, four hydrostratigraphic units were identified in the Culebra cores and were correlated with the mapping units from the WFP air intake shaft. The entire length of H-19b1 was cored and was described in detail. During coring of H-19b1, moisture was encountered in the upper part of the Dewey Lake Redbeds. A 41-ft-thick section of this core was selected for detailed description to qualify the geologic conditions related to perched water in the upper Dewey Lake. In addition to cuttings and core, a suite of geophysical logs run on the drillholes was used to identify and correlate different lithologies among the seven wells.

This paper describes an investigation of the spontaneous emission limit to the laser threshold current density in an InGaN quantum well laser. The peak gain and spontaneous emission rate as functions of carrier density are com- puted using a microscopic laser theory. From these quantities, the minimum achievable threshold current density is determined for a given threshold gain. The dependence on quantum well width, and the effects of inhomogeneous broadening due to spatial alloy variations are discussed. Also, comparison with experiments is made.

Plasma Heating in Highly Excited GaN/AIGaN Multiple Quantum @@lvEu Wells w f + 1998 %p, K. C. Zeng, R. Mair, J. Y. Liz and H. X. Jiang a) ` fabrication and understanding of MQW lasers [2-5]. For the design of these lasers, one on RT optical studies. Our results revealed that in the GaN/AIGaN MQWS, plasma heating strongly effects the carrier distribution between the confined and unconfined band-to-band and fke excitonic transitions [7]. In the MQW sample under low the unconfined states as determined from the band structure. sample under high Lxc, we varied the excitation intensity by one order of magnitude from 0.110 to IO. The carrier density is estimated to be about N=1012/cm2 (at UC= 0.1 Io) to 1013/cm2 (at 1=== l.). We plotted the PL spectra for four representative excitation fimction of injected carrier density N (open squares). The ratio starts at a value of about 18% for N=1012/cm2 (& = O. lb), and reaches a value over 64 `XO for N=1013/cm2 (& = regions is a loss to optical gain. The carrier density is ve~ high in our experiment and an electron-hole plasma (EHP) state is expected. Because the carrier transfer process plasma temperature. The laser pump energy is about 4.3 eV, which is far above the energy band gap of the sample studied here. This may result in a hot carrier population carrier densities and plasma temperatures. Using a phenomenological expression based The calculated ratio of carriers in the unconfked to the confined states (Ima~ kf) as a finction of carrier density at different temperatures are plotted in Fig. 3 (solid lines). The figure shows that the experiment results can only be explained by plasma heating of the injected carriers at high & ( TP > TJ. The transparency carrier densities for GaN/AIXGal.XN MQW structures with well thickness from 2 to 4 nm were calculated to be around 1x 1012/cm2 [10]. It is thus obvious from Fig. 3 that under high carrier injection density above the transparency density, the plasma temperature, TP, is no longer a constant. It rapidly increases with injected carrier density. Our results indicate that above the transparency carrier density, the carrier temperature may be a few due to the carrier plasma heating effect. Plasma heating makes it more difficult to obtain high quantum efficiency in the on improving the quantum efficiency of fiture GaN/AlxGalJ MQW laser structures, form an EHP and (b) plasma heating of the injected carriers strongly affects the carrier above the transparency density, the carrier plasma temperature may be a few hundred carrier density. The importance of plasma heating has both theoretical and experimental implications. It complicates the modeling of III-N lasers because plasma temperature The ratio of the PL intensities of the 25 ~ GaN/AIO.w&.mN MQW sample from fimction of injected carrier density. The open squares are experimental data and

DISTRIBUTED SENSING AND COOPERATING CONTROL FOR SWARMS OF ROBOTIC VEHICLES Key words: Distributed Sensing, Cooperative Control. ABSTRACT We discuss an approach to effectively control a large swarm of autonomous, robotic vehicles, as they per- form a search and tag operation. In particular, the robotic agents are to find the source of a chemical plume. The robotic agents work together through dis- tributed sensing and cooperative control. Distributed sensing is achieved through each agent sampling and sharing his information with others. Cooperative con- trol h accomplished by each agent u-sing its neighbors information to determine an update strategy. INTRODUCTION There is currently considerable interest in expanding the role of robotic vehicles in surveillance and inspec- tion; searching, following and t aggir-g and locating and identifying targets. In particular, researchers are beginning to focus on using small autonomous robotic vehicles for these tasks. This focus has been brought about largely because of the many recent advances in microelectronics and sensors, which include small, low power, CCD cameras; small microprocessors with ex- panded capabilities; autonomous navigation systems using GPS; and severrd types of small sensors. It seems likely that these technological advances will lead to in- expensive, easy to fabricate, autonomous vehicles out- fitted with an array of sensors. This, in turn, will allow researchers to consider teams, or even swarms, of these agents to perform a particular task. It is natural then to wonder how one might effectively control a team, or even a swarm, of robotic agents. In this paper, we discuss an approach to effectively control a large swarm of autonomous, robotic vehicles as they perform a search and tag operation. In par- ticular, the robotic agents are to find the source of a chemical plume. The robotic agents work together through distributed sensing and cooperative control. Distributed sensing is achieved through each agent sampling and sharing his information with others. Co- operative control is accomplished by each agent using its neighbors information to determine a control (or TECHNICAL DEVELOPMENT In this section we highlight the technical development of our distributed sensing and cooperative control ap- proach to effectively control a large swarm of au- tonomous, robotic vehicles. Recall that the agents are tasked with locating the chemical plume source within a chemical plume field. In our simulations, we assume that the agents are outfitted with a GPS sensor, which provides their cur- rent location, and a chemical "sniffer," which allows them to detect the strength of the chemical plume at their current location. Furthermore, we assume that the robots have onboard processing capability, and are able to communicate with one another via RF modems together with bit packing and error correction tech- niques, like those discussed by Lewis et al [4]. Thus, each agent is able to communicate and share informa- tion with all others (i.e., there is global communica- tion). In this mode, at a particular instant in time, the agents sample the chemical plume field and post this information and their current location for the oth- ers. The agents then assemble the information and de- termine a projected target of where they believe the chemical source is located. The position update for each agent is then based upon its current position and the position of the projected target.

A review is made of the infrastructure, technology and capabilities of Sandia National Laboratories for the development of micromechanical systems that have potential space applications. By incorporating advanced fabrication processes, such as chemical mechanical polishing, and several mechanical polysilicon levels, the range' of rrticromechanical systems that can be fabricated in these technologies is virtually limitless. Representative applications include a micro- engine driven mirror, and a micromachined lock. Using a novel integrated MEM!YCMOS technology, a six degree-of-freedom accelerometer/gyroscope system has been designed by researchers at U.C. Berkeley and fabricated on the same silicon chip as the CMOS control circuits to produce an integrated micro-navigational unit.

START-3 was a test program conducted in order to demonstrate and characterize the operational performance of the prototype Integrated Solar Upper Stage (ISUS) thermionic power system. The test device consisted of a graphite thermal storage uni~ multilayer foil insulation, and sixteen thermionic converters electrically connected in a series array. Several thermal input conditions were achieved during the test, which resulted in measuring converter performance at average converter hot shoe temperatures in the range of 1600 K to 2000 K. Results indicate that the ;hermionic converter; did not perform as weil as expected in the array individual sixteen converters is currently being performed.

A new method for diffusion coefficient measurement applicable to micro-fluidics is pre- sented. The method Iltilizes an analytical model describing laminar dispersion in rect- anglllar ~llicro_channe]s. The Illethod ~vas verified throllgh measllremen~ of fllloresceill diffusivity in water and aqueolls polymer solutions of differing concentration. The diffll- sivity of flllorescein was measlmed as 0.64 x 10-gm2/s in water, 0.49 x 10-gm2/s in the 4 gm/dl dextran solution and 0.38 x 10-9n12/s in the 8 gnl/dl dextran solution.

In this paper we consider the problem of simulating simple control laws involving large numbers of mobile robots. Such simulation can be computationally prohibitive if the number of robots is large enough, say 1 million, due to the 0(N2 ) cost of each time step. This work therefore uses hierarchical tree-based methods for calculating the control law. These tree-based approaches have O(NlogN) cost per time step, thus allowing for efficient simulation involving a large number of robots. For concreteness, a decentralized control law which involves only the distance and bearing to the closest neighbor robot will be considered. The time to calculate the control law for each robot at each time step is demonstrated to be O(logN).

Liquid, mixed, high-level radioactive waste (HLW) has been stored in 149 single-shell tanks (SSTS) located in tank farms on the U.S. Department of Energy's (DOE's) Hanford Site. The DOE is developing technologies to retrieve as much remaining HLW as technically possible prior to physically closing the tank farms. In support of the Hanford Tanks Initiative, Sandia National Laboratories has addressed the requirements for the regulatory closure of the radioactive component of any SST residue that may remain after physical closure. There is significant uncertainty about the end state of each of the 149 SSTS; that is, the nature and amount of wastes remaining in the SSTS after retrieval is uncertain. As a means of proceeding in the face of these uncertainties, this report links possible end-states with associated closure options. Requirements for disposal of HLW and low-level radioactive waste (LLW) are reviewed in detail. Incidental waste, which is radioactive waste produced incidental to the further processing of HLW, is then discussed. If the low activity waste (LAW) fraction from the further processing of HLW is determined to be incidental waste, then DOE can dispose of that incidental waste onsite without a license from the U.S. Nuclear Regulatory Commissions (NRC). The NRC has proposed three Incidental Waste Criteria for determining if a LAW fraction is incidental waste. One of the three Criteria is that the LAW fraction should not exceed the NRC's Class C limits.

Research is in progress to develop microminiature thermionic converters (MTCS) with high energy conversion efficiencies and variable operating temperatures using semiconductor integrated circuit (IC) fabrication methods. The use of IC techniques allows the fabrication of MTCS with cathode to anode spacing of several microns or less and with anode and cathode materials that will have work fimctions ranging from 1 eV to 3 eV. The small cathode to anode spacing and variable electrode work functions should allow the conversion of heat energy to relatively large current densities (up to tens of Amps/cmz) at relatively high conversion efficiencies ( 15-25%).

An operational evaluation of the Integrated Solar Upper Stage (ISUS) power management and distribution (PMAD) system was conducted as part of the Engine Ground Demonstration thermionic power system test program-- START-3. START-3 testing took place at the Baikal Test Stand, located in the University of New Mexico's Energy Conversion Research Laboratory at the New Mexico Engineering Research Institute in Albuquerque, NM. One objective of this test was to evaluate the operational performance of the lSUS PMAD system developed by the National Aeronautics and Space Administration (NASA) Lewis Research Center. Tests of the PMAD with the ISUS diode string demonstrated that the PMAD could regulate the output of an array of thermionic converters within the design requirements and couId be modified to optimize performance for diode strings of fewer than 16 diodes.

In support of the National Transportation Safety Board investigation of the TWA Flight 800 accident, a combined experimental/computational effort was conducted that focused on quarter-scale testing and simulation of the fuel-air explosion in the Boeing 747 center wing fuel tank. This report summarizes the modeling approach used at Sandia National Laboratories. In this approach approximations are introduced that capture the essential physics associated with turbulent flame propagation in multiple compartment fuel tanks. This model efficiently defines the pressure loading conditions during a jet-fuel air explosion in a fuel tank confinement. Modeling calculations compare favorably with a variety of experimental quarter-scale tests conducted in rigid confinement. The modeling describes well the overpressure history in several geometry configurations. Upon demonstrating a reasonable comparison to experimental observations, a parametric study of eight possible ignition sources is then discussed. Model calculations demonstrate that different loading conditions arise as the location of the ignition event is varied. By comparing the inferred damage and calculated impulses to that seen in the recovered tank, it maybe possible to reduce the number of likely sources. A possible extension of this work to better define tank damage includes coupling the combustion model as a pressure loading routine for structural failure analysis.

The emerging technology of pulsed intense ion beams has been shown to lead to improvements in surface characteristics such as hardness and wear resistance, as well as mechanical smoothing. We report hereon the use of this technology to systematically study improvements to three types of metal alloys - aluminum, iron, and titanium. Ion beam tieatment produces a rapid melt and resolidification (RMR) of the surface layer. In the case of a predeposited thin-fihn layer, the beam mixes this layer into the substrate, Ieading to improvements that can exceed those produced by treatment of the alloy alone, In either case, RMR results in both crystal refinement and metastable state formation in the treated surface layer not accessible by conventional alloy production. Although more characterization is needed, we have begun the process of relating these microstructural changes to the surface improvements we discuss in this report.

The purpose of this work was to explore the use of immersive technologies, such as those used in synthetic environments (commordy referred to as virtual realily, or VR), in enhancing the mesh- generation process for 3-dimensional (3D) engineering models. This work was motivated by the fact that automatic mesh generation systems are still imperfect - meshing algorithms, particularly in 3D, are sometimes unable to construct a mesh to completion, or they may produce anomalies or undesirable complexities in the resulting mesh. It is important that analysts and meshing code developers be able to study their meshes effectively in order to understand the topology and qualily of their meshes. We have implemented prototype capabilities that enable such exploration of meshes in a highly visual and intuitive manner. Since many applications are making use of increasingly large meshes, we have also investigated approaches to handle large meshes while maintaining interactive response. Ideally, it would also be possible to interact with the meshing process, allowing interactive feedback which corrects problems and/or somehow enables proper completion of the meshing process. We have implemented some functionality towards this end -- in doing so, we have explored software architectures that support such an interactive meshing process. This work has incorporated existing technologies developed at SandiaNational Laboratories, including the CUBIT mesh generation system, and the EIGEN/VR (previously known as MUSE) and FLIGHT systems, which allow applications to make use of immersive technologies and advanced human computer interfaces. 1

A bibliography has been compiled dealing with the verification and validation of computational simulations. The references listed in this bibliography are concentrated in the field of computational fluid dynamics (CFD). However, references from the following fields are also included: operations research, heat transfer, solid dynamics, software quality assurance, software accreditation, military systems, and nuclear reactor safety. This bibliography, containing 221 references, is not meant to be comprehensive. It was compiled during the last ten years in response to the author's interest and research in the methodology for verification and validation. The emphasis in the bibliography is in the following areas: philosophy of science underpinnings, development of terminology and methodology, high accuracy solutions for CFD verification, experimental datasets for CFD validation, and the statistical quantification of model validation. This bibliography should provide a starting point for individual researchers in many fields of computational simulation in science and engineering.

Bomb Detection Using Backscattered X-rays* Currently the most common method to determine the contents of a package suspected of containing an explosive device is to use transmission radiography. This technique requires that an x-ray source and film be placed on opposite sides of the package. This poses a problem if the pachge is placed so that only one side is accessible, such as against a wall. There is also a threat to persomel and property since exTlosive devices may be "booby trapped." We have developed a method to x-ray a paclage using backscattered x-rays. This procedure eliminates the use of film behind the target. All of the detection is done from the same side as the source. When an object is subjected to x-rays, some of them iare scattered back towards the source. The backscattenng of x-rays is propordoml to the atomic number (Z) of the material raised to the 4.1 power. This 24"' dependence allows us to easily distinguish between explosives, wires, timer, batteries, and other bomb components. Using transmission radiography-to image the contents of an unknown package poses some undesirable risks. The object must have an x-ray film placed on the side opposite the x-ray source; this cannot be done without moving the package if it has been placed firmly against a wall or pillar. Therefore it would be extremely usefid to be able to image the contents of a package from only one side, without ever having to disturb the package itself. where E is the energy of the incoming x-ray. The volume of x-rays absorbed is important because it is, of course, directly correlated to the intensity of x-mys that will be scattered. Most of the x-rays that scatter will do so in a genemlly forward direction; however, a small percentage do scatter in a backward direction. Figure 1 shows a diagram of the various fates of x-rays directed into an object. The package that was examined in this ex~enment was an attache case made of pressed fiberboardwith a vinyl covering. It was approxirmtely 36 cm wide by 51 cm long by 13 cm deep. The case was placed on an aluminum sheet under the x-ray source. Because of the laborato~ setup, the attache case was rastered in the y-coordinate direction, while the x-ray source mstered in the x-coordinate direction. However, for field use, the x-ray source would of course raster in both the x- and y-coordinate directions, while the object under interrogation would remain stationary and undisturbed. A mobile system for use by law enforcement agencies or bomb disposal squads needs to be portable and somewhat durable. A 300 kV x-ray source should be sufficient for the task requirements and can be mounted on a mobile system. A robotic carriage could be used to transport the x-ray source and the CCD camera to the proximity of the suspect package. The controlling and data analyzing elements of the system' could then be maintained at a &tie distance from the possible explosive. F@re 8 shows a diagram of a conceptual design of a possible system for this type of use. The use of backscattered x-rays for interrogation of packages that may contain explosive devices has been shown to be feasible inthelaboratory. Usinga 150kVx-ray source anddetectors consisting of plastic scintillating material, all bomb components including the wiring were detectable. However, at this time the process requires more time than is desirable for the situations in which it will most likely be needed. Further development of the technology using CCD cameras, rather than the plastic stint illator detectors, shows promise of leading to a much faster system, as well as one with better resolution. Mounting the x- ray source and the CCD camera on a robotic vehicle while keeping the controlling and analyzing components and the opemting personnel a safe distance away from the suspect package will allow such a package to be examined at low risk to human life.

The ATM Forum UNI 4.0 Security Addendum has undergone 4 revisions and has been without substantive modifications for 3 ATM Forurn meetings. This contribution is intended to assist the ATM Forum CS Working Group in the process of bringing BTD-CS-UNI-SEC-O1 .04 DIUFT to Straw Ballot. This effort applies equally to its companion documen~ BTD-CS-PNNI-SEC-O 1.02 DRAFT. BTD-CS-UNI-SEC-01 .04 DRAFT is an addendum to UNI 4.0 Signaling that describes the additional procedures needed of ATM signaling to support the signaling-based securily message exchange protocol, and its 4 basic security mechanisms, authentication, confidentiality, integrity and access control for ATM VC/VPs. These services are specified in detail in ATM Forurn document af-sec-0100.000, which is currently in Final Ballot. The remaining identified work for BTD-CS-UNI-SEC-01 .04 DRAFT includes the resolution of the TBD items in the draft, and a review of the sections of the ATM Forum Security Specification V 1.0 af-sec- 0100.000, that are specifically referenced by BTD-CS-UNI-SEC-O 1.04 DRAFT. In support of this effort, this contribution includes the relevant baseline text of the referenced sections of that Security Specification.

This contribution proposes a 64 bit wide bus structure that will operate at rates inexcess of lO Gbps asa strawmanfora OC192c Utopia Specification.

This contribution proposes a 128 bit wide interface structure clocked at approximately 80 MHz that will operate at 10 Gbps as a strawman for a 0C192C Utopia Specification. In addition, the concept of scalable width of data transfers in order to maintain manageably low clock rates is proposed.

Abstract not provided.

The ADROIT Analysis of Dispersal Risk Qccurring in transportation code is the primary tool used to perform probabilistic risk assessments for the Transportation Safeguards Division of the Department of Energy. The current version of ADROIT uses a Pasquill-Gifford stability-class approach to meteorological characterization. In order to assess the affect that this simplified approach to weather characterization has on ADROIT'S predictions of consequence and risk, the Pasquill-Gifford stability-class approach was replaced with a direct use of radiosonde data from the National Climatic Data Center (NCDC). A comparison of results obtained for the two weather characterizations shows that, under certain circumstances, the use of the stability-class approach can result in a significant underprediction of consequence and risk values. Since such an underprediction is non-consewative, it is recommended that the stability-class approach currently used by ADROIT be replaced with a more detailed characterization of meteorological conditions. Specifically, the NCDC database was found to have sufllcient temporal and spatial resolution for ADROIT applications. Understanding that an attempt to use of all of the NCDC data in ADROIT would be prohibitive, a sampling scheme is presented as a viable alternative for instituting the recommendation of this study.

This investigation is concerned with the accuracy of numerical schemes for solving partial differential equations used in science and engineering simulation codes. Richardson extrapolation methods for steady and unsteady problems with structured meshes are presented as part of the verification procedure to determine code and calculation accuracy. The local truncation error de- termination of a numerical difference scheme is shown to be a significant component of the veri- fication procedure as it determines the consistency of the numerical scheme, the order of the numerical scheme, and the restrictions on the mesh variation with a non-uniform mesh. Genera- tion of a series of co-located, refined meshes with the appropriate variation of mesh cell size is in- vestigated and is another important component of the verification procedure. The importance of mesh refinement studies is shown to be more significant than just a procedure to determine solu- tion accuracy. It is suggested that mesh refinement techniques can be developed to determine con- sistency of numerical schemes and to determine if governing equations are well posed. The present investigation provides further insight into the conditions and procedures required to effec- tively use Richardson extrapolation with mesh refinement studies to achieve confidence that sim- ulation codes are producing accurate numerical solutions.

The Department of Energy (DOE) has developed the Waste Isolation Pilot Plant (WIPP) for the purpose of demonstrating safe management, storage, and disposal of radioactive transuranic (TRU) waste generated by U.S. defense programs. The WIPP is located in southeastern New Mexico, and the underground facilities of the WIPP (i.e., experimental rooms, disposal rooms, etc.) are sited in the bedded salt of the Salado Formation at a depth of about 660 meters. The DOE has authorized the continuance of scientific research and engineering analysis related to the performance of the WIPP repository. One area of additional research relates to characterization of the mechanical and hydrological properties of anhydrite interbeds within the Salado Formation. These anhydrite interbeds have been penetrated by the shafts that provide access to the underground facilities and also lie in close proximity to the proposed radioactive waste disposal rooms at the repository horizon. Properties of particular interest are mechanical strength, deforrnational behavior, and fluid transport properties such as permeability. These properties will be used in calculationskmalyses of the mechanical and hydrological behavior of the anhydrite, in particular, and the shaft sealing system and disposal rooms, in general.

This paper outlines the results of a cooperative effort between Sandia National Laboratories, Associated Power Analysts, Inc. and Texas A&M University to characterize the impact of a changing regulatory environment on the reliability of customer electrical service. It was desired to assess the impact in as realistic an environment as possible. Due the availability of data the initial study centered on the electric power grid in Texas. Specifically, data from the Electric Reliability Council of Texas (ERCOT) for the 1997 operational year was used in the research. Based on geography and location of generation and transmission lines, ten basic areas were considered and each area was modeled as a single point generation and load. A number of restructuring scenarios were developed by researchers at Sandia National Laboratories and investigated by Associated Power Analysts using their N-Area Reliability Program (NARP). The present study is limited to an assessment of the adequacy aspects of reliability: sufficiency of installed generation and transmission capacity to satisfy the needs of all consumers in a steady- state sense. The results are, on one hand conservative in that they address on] y the impact of peak loading. Alternatively, the~ are optimistic in that the transmission lines are assumed to be in continuous operation. The major results of this study indicate that, in anew regulatory era, the reliability of customer service will be significantly impacted, possibly in a negative fashion, unless the effects of the ensuing economic pressures are understood and appropriate actions taken.

Distributed systems have been studied for twenty years and are now coming into wider use as fast networks and powerful workstations become more readily available. In many respects a massively parallel computer resembles a network of workstations and it is tempting to port a distributed operating system to such a machine. However, there are significant differences between these two environments and a parallel operating system is needed to get the best performance out of a massively parallel system. This report characterizes the differences between distributed systems, networks of workstations, and massively parallel systems and analyzes the impact of these differences on operating system design. In the second part of the report, we introduce Puma, an operating system specifically developed for massively parallel systems. We describe Puma portals, the basic building blocks for message passing paradigms implemented on top of Puma, and show how the differences observed in the first part of the report have influenced the design and implementation of Puma.

Sandia's entry into utilizing clusters of networked workstations is called Computational Plant or CPlant for short. The design of CPlant uses Ethernet to boot the individual nodes, Myrinet to communicate within a node cluster, and ATM to connect between remote clusters. This SAND document covers the work done to enable the use of ATM on the CPlant nodes in the Fall of 1997.

This report reviews the history, theory and mathematics of wavelet analysis. Examination of the Fourier Transform and Short-time Fourier Transform methods provides tiormation about the evolution of the wavelet analysis technique. This overview is intended to provide readers with a basic understanding of wavelet analysis, define common wavelet terminology and describe wavelet amdysis algorithms. The most common algorithms for performing efficient, discrete wavelet transforms for signal analysis and inverse discrete wavelet transforms for signal reconstruction are presented. This report is intended to be approachable by non- mathematicians, although a basic understanding of engineering mathematics is necessary.

There have existed for some time relatively sparse creep databases for a number of domal salts. Although all of these data were analyzed at the time they were reported, to date there has not been a comprehensive, overall evaluation within the same analysis framework. Such an evaluation may prove of value. The analysis methodology is based on the Multimechanism Deformation (M-D) description of salt creep and the corresponding model parameters determined from conventional creep tests. The constitutive model of creep wss formulated through application of principles involved in micromechanical modeling. It was possible, at minimum, to obtain the steady state parameters of the creep model from the data on the domal salts. When this was done, the creep of the domal salts, as compared to the well-defined Waste Isolation Pilot Plant (WIPP) bedded clean salt, was either essentially identical to, or significantly harder (more creep resistant) than WIPP salt. Interestingly, the domal salts form two distinct groups, either sofl or hard, where the difference is roughly a factor often in creep rate between the twcl groups. As might be expected, this classification corresponds quite well to the differences in magnitude of effective creep volume losses of the Strategic Petroleum Reserve (SPR) caverns as determined by the CAVEMAN cavern pressure history analysis, depending upon the specific dome or region within the dome. Creep response shoulcl also correlate to interior cavern conditions that produce salt falls. WMle, in general, the caverns in hard sah have a noticeably greater propensity for salt falls, a smaller number of similar events are exhibited even in the caverns in soft salt.

This white paper presents the initial requirements for developing a new computer model for simulating the effects of extreme acts of terrorism in the United States. General characteristics of the model are proposed and the level of effort to prepare a complete written description of the model, prior to coding, is detailed. The model would simulate the decision processes and interactions of complex U. S. systems engaged in responding to and recovering from four types of terrorist incidents. The incident scenarios span the space of extreme acts of terrorism that have the potential to affect not only the impacted area, but also the entire nation. The model would be useful to decision-makers in assessing and analyzing the vulnerability of the nation's complex infrastructures, in prioritizing resources to reduce risk, and in planning strategies for immediate response and for subsequent recovery from terrorist incidents.

The Campus Executive Program sponsored this research at Cornell University. The research was directed toward the implementation of laser-based diagnostics for wire-array Z-pinches. Under this contract we were able to carry out all the necessary preparations to setup the laser diagnostics to complement our x-ray backlighting measurements of the early phase of exploding wire z-pinch plasma formation.

Computationally intelligent recognition of characters and symbols addresses a wide range of applications including foreign language translation and chemical formula identification. The combination of intelligent learning and optimization algorithms with layered neural structures offers powerful techniques for character recognition. These techniques were originally developed by Sandia National Laboratories for pattern and spectral analysis; however, their ability to optimize vast amounts of data make them ideal for character recognition. An adaptation of the Neural Network Designer soflsvare allows the user to create a neural network (NN_) trained by a genetic algorithm (GA) that correctly identifies multiple distinct characters. The initial successfid recognition of standard capital letters can be expanded to include chemical and mathematical symbols and alphabets of foreign languages, especially Arabic and Chinese. The FIN model constructed for this project uses a three layer feed-forward architecture. To facilitate the input of characters and symbols, a graphic user interface (GUI) has been developed to convert the traditional representation of each character or symbol to a bitmap. The 8 x 8 bitmap representations used for these tests are mapped onto the input nodes of the feed-forward neural network (FFNN) in a one-to-one correspondence. The input nodes feed forward into a hidden layer, and the hidden layer feeds into five output nodes correlated to possible character outcomes. During the training period the GA optimizes the weights of the NN until it can successfully recognize distinct characters. Systematic deviations from the base design test the network's range of applicability. Increasing capacity, the number of letters to be recognized, requires a nonlinear increase in the number of hidden layer neurodes. Optimal character recognition performance necessitates a minimum threshold for the number of cases when genetically training the net. And, the amount of noise significantly degrades character recognition efficiency, some of which can be overcome by adding noise during training and optimizing the form of the network's activation fimction.

The goal of the 7th International Meshing Roundtable is to bring together researchers and developers from industry, academia, and government labs in a stimulating, open environment for the exchange of technical information related to the meshing process. In the past, the Roundtable has enjoyed significant participation from each of these groups from a wide variety of countries.

Use of nature`s laboratory for scientific analysis of complex systems is a largely untapped resource for understanding long-term disposal of hazardous materials. The Waste Isolation Pilot Plant (WIPP) in the US is a facility designed and approved for storage of transuranic waste in a salt medium. Isolation from the biosphere must be ensured for 10,000 years. Natural analogs provide a means to interpret the evolution of the underground disposal setting. Investigations of ancient sites where manmade materials have experienced mechanical and chemical processes over millennia provide scientific information unattainable by conventional laboratory methods. This paper presents examples of these pertinent natural analogs, provides examples of features relating to the WIPP application, and identifies potential avenues of future investigations. This paper cites examples of analogical information pertaining to the Hallstatt salt mine in Austria and Wieliczka salt mine in Poland. This paper intends to develop an appreciation for the applicability of natural analogs to the science and engineering of a long-term disposal facility in geomedia.

The United States Department of Energy Office of Environmental Management's (DOE/EM's) National Spent Nuclear Fuel Program (NSNFP), through a collaboration between Sandia National Laboratories (SNL) and Idaho National Engineering and Environmental Laboratory (INEEL), is conducting a systematic Nuclear Dynamics Consequence Analysis (NDCA) of the disposal of SNFs in an underground geologic repository sited in unsaturated tuff. This analysis is intended to provide interim guidance to the DOE for the management of the SNF while they prepare for final compliance evaluation. This report presents results from a Nuclear Dynamics Consequence Analysis (NDCA) that examined the potential consequences and risks of criticality during the long-term disposal of spent nuclear fuel owned by DOE-EM. This analysis investigated the potential of post-closure criticality, the consequences of a criticality excursion, and the probability frequency for post-closure criticality. The results of the NDCA are intended to provide the DOE-EM with a technical basis for measuring risk which can be used for screening arguments to eliminate post-closure criticality FEPs (features, events and processes) from consideration in the compliance assessment because of either low probability or low consequences. This report is composed of an executive summary (Volume 1), the methodology and results of the NDCA (Volume 2), and the applicable appendices (Volume 3).

A mechanical characterization of frozen silty soils has been conducted to support computer modeling of penetrators. The soils were obtained from the Eilson AFB (Alaska) vicinity. Quasi-static testing with a multiaxial system in a cold room and intermediate strain rate testing with a split Hopkinson pressure bar were conducted. Maximum stresses achieved were slightly above 1 GPa, apparently limiting the observed behavior primarily to elastic compression and pore crushing phenomena. Lower temperatures seem to increase the strength of the material markedly, although not by a simple factor. Lower temperatures and higher strain rates increase the apparent Young's and bulk moduli as well (an increase of {approximately} a factor of two is observed for strain rate increasing from 0.001 s{sup {minus}1} to 800 s{sup {minus}1}). The strength also depends strongly on strain rate. Increasing the strain rate from 0.001 {sup {minus}1} to 0.07 {sup {minus}1} increases the strength by a factor of five to ten (to values of order 1 GPa). However,only a small increase in strength is seen as strain rate is increased to {approximately} 10{sup 2}--10{sup 3} s{sup {minus}1}. The reliability of the strength measurements at strain rates< 1 s{sup {minus}1} is decreased due to details of the experimental geometry, although general trends are observable. A recipe is provided for a simulant soil based on bentonite, sand, clay-rich soil and water to fit the {approximately} 6% air-filled porosity, density and water content of the Alaska soils, based on benchtop mixing and jacketed compression testing of candidate mixes.

The purpose of this document is to present a strategy for effectively using SMSS (Sea.leable Mass Storage System) and to distribute a simple implementation of this strategy. This work was done as a stopgap memure to ~lOW ~ ~~yst to USe the storage Power of SMSS in the absence of a more user friendly interface. The features and functionality discussed in this document represent a minimum set of capabilities to allow a useful archiving interface functionality. The implementation presented is the most basic possible and would benefit significantly from an organized support and documentation effort.

This report summarizes a three-year project to characterize and improve the ride quality of the Department of Energy (DOE) tractor/trailer. A high-fidelity computer model was used to simulate the vibrational response in the passenger compartment of the truck due to a common roadway environment. It is the intensity of this response that is indicative of the ride quality of the vehicle. The computational model was then validated with experimental tests using a novel technique employing both lab-based modal tests and modal data derived using the Natural Excitation Technique (NExT). The validated model proved invaluable as a design tool. Utilizing the model in a predictive manner, modifications to improve ride quality were made to both the existing vehicle and the next-generation design concept. As a result, the next-generation fleet of tractors (procurement process begins in FY98) will incorporate elements of a successful model-based design for improved truck ride.

As feature sizes of Integrated Circuits (ICs) continue to shrinlL the sensitivity of these devices, particularly SRAMS and DR4Ms, to natural radiation is increasing. The radiation can lead to the uncontrolled deposition of charge within an IC, which ean alter, for example, the memoty state of a bit and thereby produce what is edled a `SOW error, or Single Event Upset (SEU). The response of ICS to natural background radiation is therefore of great coneem regarding the reliability of Mure devices. In this paper, we present results where Ion Beam Induced Charge Collection (TBICC) technique was used to simulate neutron-induced Si recoil dlkcts in IC test structures. The present wo~ wnducted at the San& National Laboratories, uses a 10 MeV Carbon mierobeam with 1 pm spot to scan test structures on specifically designed ICS. The test structure contains junctions typical of S RAMS and DRAMs. Charge is eolleeted from different areas of the IC under various conditions of junction back bias. The data are digitized and displayed as 3D images combined with KY) coordination. With the aid of IC layout informatio~ the 3D images are sepamted into difTerent layers to allow the identification of charge collection etlciency in the test structures. An analysis of the charge collection efficiency from dillerent test areas is given.

The critical energy inkstructures include gas, OL and electric power. These Mrastructures are complex and interdependent nmvorks that are vital to the national secwiy and social well being of our nation. Many electric power systems depend upon gas and oil, while fossil energy delive~ systems depend upon elecnic power. The control mechanisms for these Mrastructures are often referred to as SCADA (Supmivry CkmdandDaU Ac@itz&z) systems. SCADA systems provide remote monitoring and centralized control for a distributed tmnsportation infmsmucture in order to facilitate delivery of a commodi~. AIthough many of the SCADA concepts developed in this paper can be applied to automotive mmsponation systems, we will use transportation to refer to the movement of electrici~, gas, and oil. \ Recently, there have been seveml reports suggesting that the widespread and increasing use of SCADA for control of energy systems provides an increasing opportuni~ for an advers~ to cause serious darnage to the energy inbstmcturei~. This damage could arise through cyber infiltration of the SCADA networks, by physically tampering with the control networks, or through a combination of both means. SCADA system threats decompose into cyber and physical threats. One solution to the SCADA security problem is to design a standard for a highly secure KA.DA system that is both cyber, and physdly secure. Not all-physical threats are possible to guard again% but of those threats that are, high security SCADA provides confidence that the system will continue to operate in their presence. One of the most important problems in SCADA securi~ is the relationship between the cyber and physical vulnerabilities. Cyber intrusion increases physical Vulnerabilities, while in the dual problem physical tampering increases cyber vulnerabilit.ies. There is potential for feedback and the precise dynamics need to be understood. As a first step towards a stan~ the goal of this paper is to facilitate a discussion of the requirements analysis for a highly secure SCADA system. The fi-arnework for the discussion consists of the identification of SCADA security investment areas coupled with the tradeoffs that will force compromises in the solution. For example, computational and bandwidth requirements of a security standard could force the replacement of entire SCADA systems. The requirements for a real-time response in a cascading electric power failure could pose limitations on authentication and encryption mechanisms. The shortest path to the development of a high securi~ SC.ADA standard will be achieved by leveraging existing standards efforts and ensuring that security is being properly addressed in those standards. The Utility Communications Architecture 2.o (UC@, for real-time utili~ decision control, represents one such standard. The development of a SCADA secwiy specification is a complex task that will benefit from a systems engineering approach.

The key to insight is coupling the power of the computer with unique skills of the human. At Sandia National Laboratories' Interaction Laboratory, we call this teraflop visualization. We are concentrating research in three main area: 1) using the computer as a facility for authoring content, 2) adding the physics to model real behaviors, and 3) allowing the human to utilize the improved precision and resolution provided by this new class of compute power.

Demonstrating compliance with the applicable regulations for the Waste Isolation Pilot Plant (WIPP) requires an assessment of the long-term performance of the disposal system. Scenario development is one starting point of this assessment, and generates inquiry about the present state and future evolution of the disposal system. Scenario development consists of four tasks: (1) identifying and classifying features, events and processes (FEPs), (2) screening FEPs according to well-defined criteria, (3) forming scenarios (combinations of FEPs) in the context of regulatory performance criteria and (4) specifying of scenarios for consequence analysis. The development and screening of a comprehensive FEP list provides assurance that the identification of significant processes and events is complete, that potential interactions between FEPs are not overlooked, and that responses to possible questions are available and well documented. Two basic scenarios have been identified for the WIPP: undisturbed performance (UP) and disturbed performance (DP). The UP scenario is used to evaluate compliance with the Environmental Protection Agency's (EPA's) Individual Dose (40 CFR Section 191-15) and Groundwater Protection (40 CFR Section 191-24) standards and accounts for all natural-, waste- and repository-induced FEPs that survive the screening process. The DP scenario is required for assessment calculations for the EPA's cumulative release standard (Containment Requirements, 40 CFR Section 191-13) and accounts for disruptive future human events, which have an uncertain probability of occurrence, in addition to the UP FEPs.

Refractory ternary nitride films for diffusion barriers in microelectronics have been grown using chemical vapor deposition. Thin films of titanium-silicon-nitride, tungsten-boron-nitride, and tungsten-silicon-nitride of various compositions have been deposited on 150 mm Si wafers. The microstructure of the films are either fully amorphous for the tungsten based films, or nauocrystalline TiN in an amorphous matrix for titanium-silicon-nitride. All films exhibit step coverages suitable for use in future microelectronics generations. Selected films have been tested as diffusion barriers between copper and silicon, and generally perform extremely weH. These fiIms are promising candidates for advanced diffusion barriers for microelectronics applications. The manufacturing of silicon wafers into integrated circuits uses many different process and materials. The manufacturing process is usually divided into two parts: the front end of line (FEOL) and the back end of line (BEOL). In the FEOL the individual transistors that are the heart of an integrated circuit are made on the silicon wafer. The responsibility of the BEOL is to wire all the transistors together to make a complete circuit. The transistors are fabricated in the silicon itself. The wiring is made out of metal, currently aluminum and tungsten, insulated by silicon dioxide, see Figure 1. Unfortunately, silicon will diffuse into aluminum, causing aluminum spiking of junctions, killing transistors. Similarly, during chemical vapor deposition (CVD) of tungsten from ~fj, the reactivity of the fluorine can cause "worn-holes" in the silicon, also destroying transistors. The solution to these problems is a so-called diffusion barrier, which will allow current to pass from the transistors to the wiring, but will prevent reactions between silicon and the metal.

Shock equation of state and strength data have been obtained on the explosive PBXW-128 over the pressure range O-3 GPa using gun impact techniques and velocity interferometry diagnostics. Nonlinear shock-velocity-versus-particle velocity behavior is observed. Possible mechanisms are discussed and a Hug.oniot equation of slate model for the data is provided.

High sensitivity acoustic wave chemical microsensors are being developed on GaAs substrates. These devices take advantage of the piezoelectric properties of GaAs as well as its mature microelectronics fabrication technology and nascent micromachining technology. The design, fabrication, and response of GaAs SAW chemical microsensors are reported. Functional integrated GaAs SAW oscillators, suitable for chemical sensing, have been produced. The integrated oscillator requires 20 mA at 3 VK, operates at frequencies up to 500 MHz, and occupies approximately 2 mmz. Discrete GaAs sensor components, including IC amplifiers, SAW delay lines, and IC phase comparators have been fabricated and tested. A temperature compensation scheme has been developed that overcomes the large temperature dependence of GaAs acoustic wave devices. Packaging issues related to bonding miniature flow channels directly to the GaAs substrates have been resolved. Micromachining techniques for fabricating FPW and TSM microsensors on thin GaAs membranes are presented and GaAs FPW delay line performance is described. These devices have potentially higher sensitivity than existing GaAs and quartz SAW sensors.

The Waste Isolation Pilot Plant (WPP) is located in southeastern New Mexico and is being developed by the U.S. Department of Energy (DOE) for the geologic (deep underground) disposal of transuranic (TRU) waste. A detailed performance assessment (PA) for the WIPP was carried out in 1996 and supports an application by the DOE to the U.S. Environmental Protection Agency (EPA) for the certification of the WIPP for the disposal of TRU waste. The 1996 WIPP PA uses a computational structure that maintains a separation between stochastic (i.e., aleatory) and subjective (i.e., epistemic) uncertainty, with stochastic uncertainty arising from the many possible disruptions that could occur over the 10,000 yr regulatory period that applies to the WIPP and subjective uncertainty arising from the imprecision with which many of the quantities required in the PA are known. Important parts of this structure are (1) the use of Latin hypercube sampling to incorporate the effects of subjective uncertainty, (2) the use of Monte Carlo (i.e., random) sampling to incorporate the effects of stochastic uncertainty, and (3) the efficient use of the necessarily limited number of mechanistic calculations that can be performed to support the analysis. The use of Latin hypercube sampling generates a mapping from imprecisely known analysis inputs to analysis outcomes of interest that provides both a display of the uncertainty in analysis outcomes (i.e., uncertainty analysis) and a basis for investigating the effects of individual inputs on these outcomes (i.e., sensitivity analysis). The sensitivity analysis procedures used in the PA include examination of scatterplots, stepwise regression analysis, and partial correlation analysis. Uncertainty and sensitivity analysis results obtained as part of the 1996 WIPP PA are presented and discussed. Specific topics considered include two phase flow in the vicinity of the repository, radionuclide release from the repository, fluid flow and radionuclide transport in formations overlying the repository, and complementary cumulative distribution functions used in comparisons with regulatory standards (i.e., 40 CFR 191, Subpart B).

Falling water drops can collect particles and soluble or reactive vapor from the gas through which they fall. Rain is known to remove particles and vapors by the process of rainout. Water sprays can be used to remove radioactive aerosol from the atmosphere of a nuclear reactor containment building. There is a potential for water sprays to be used as a mitigation technique to remove chemical or bio- logical agents from the air. This paper is a quick-look at water spray removal. It is not definitive but rather provides a reasonable basic model for particle and gas removal and presents an example calcu- lation of sarin removal from a BART station. This work ~ a starting point and the results indicate that further modeling and exploration of additional mechanisms for particle and vapor removal may prove beneficial.

This report describes the Sandia activities in the developing field management approach to enhancing National Laboratories (Sandia) educational outreach of architectural and infrastructure surety, a risk the safety, security, and reliability of facilities, systems, and structures. It begins with a description of the field of architectural and infrastmcture surety, including Sandia's historical expertise and experience in nuclear weapons surety. An overview of the 1996 Sandia Workshop on Architectural SuretysM is then provided to reference the initiation of the various activities. This workshop established the need for a surety education program at the University level and recommended that Sandia develop the course material as soon as possible. Technical material was assembled and the course was offered at the University of New Mexico (UNM) during the 1997 spring semester. The bulk of this report accordingly summarizes the lecture material presented in this pioneering graduate-level course on Infrastructure Surety in the Civil Engineering Department at UNM. This groundbreaking class presented subject matter developed by experts from Sandia, and included additional information from guest lecturers from academia, government, and industry. Also included in this report are summaries of the term projects developed by the graduate students, an overview of the 1997 International Conference on Architectural Suretp: Assuring the Performance of Buildings and Injiastruchwes (co-sponsored by Sandia, the American Institute of Architects, and the American Society of Civil Engineers), and recommendations for further course work development. The U.S. Department of Energy provides support to this emerging field of architectural and infrastructure surety and recognizes its broad application to developing government, industry, and professional standards in the national interest.

The analysis presented herein predicts that, under signal-independent noise limited conditions, an Information-efficient Spectral Imaging Sensor (ISIS) style hyperspectral imaging system design can obtain significant signal-to-noise ratio (SNR) and speed increase relative to a comparable traditional hyperspectral imaging (HSI) instrument. Factors of forty are reasonable for a single vector, and factors of eight are reasonable for a five-vector measurement. These advantages can be traded with other system parameters in an overall sensor system design to allow a variety of applications to be done that otherwise would be impossible within the constraints of the traditional HSI style design.

Several types of commercial fiber optic connectors were characterized for potential use in a Sandia designed Laser Diode Ignition (LDI) system. The characterization included optical performance while the connectors were subjected to the more dynamic environmental conditions experienced in weapons applications. The environmental testing included temperature cycling, random vibration, and mechanical shock. This report presents a performance assessment of the fiber optic connectors and fiber included in the characterization. The desirable design features are described for a fiber optic connector that must survive the dynamic environment of weapon systems. The more detailed performance of each connector type will be included as resources permit.

An experimental investigation has confirmed the predicted flow pattern in a prototype virtual cyclone, a novel device for nonimpact particle separation proposed by Torcdzynski and Rader (1996, 1997) based solely on computational simulations. The virtual cyclone differs from an ordinary cyclone in that the flow is turned by a virtual wall composed of an eddy rather than by a solid wall. A small-scale version of the computationally simulated geometry has been fabricated out of Lucite. The working fluid is ambient air, which is drawn through the apparatus and flow-metering equipment using a wind-tunnel vacuum source. The flow is seeded with smoke or water droplets produced by a nebulizer so that flow visualization techniques and particle-imaging velocimetry could be applied. Experiments have been performed on this apparatus for flows with Reynolds numbers from 200 up to 40,000 (a Mach number of 0.3). Flow visualization using a laser light sheet passing through the mid-plane of the apparatus verified that the computationally predicted flow is obtained over the entire range of flow rates. The shear layer between the main and recirculating flow is observed to become turbulent around a Reynolds number of 4000. While not changing the flow structure, the turbulent mixing produced by shear-layer roll-up limits particle concentration at the higher flow rates. In order to achieve highly efficient particle separation using a virtual cyclone, turbulence must be suppressed or mitigated. If laminar flow cannot be achieved for macroscopic-scale virtual cyclones, it should be achievable for a small-scale (low Reynolds number) virtual cyclone fabricated using MEMS-related technologies. This approach could lead to a chip-scale particle concentrator.

SAR imagery for coastline detection has many potential advantages over conventional optical stereoscopic techniques. For example, SAR does not have restrictions on being collected during daylight or when there is no cloud cover. In addition, the techniques for coastline detection witth SAR images can be automated. In this paper, we present the algorithmic development of an automatic coastline detector for use with SAR imagery. Three main algorithms comprise the automatic coastline detection algorithm, The first algorithm considers the image pre-processing steps that must occur on the original image in order to accentuate the land/water boundary. The second algorithm automatically follows along the accentuated land/water boundary and produces a single-pixel-wide coastline. The third algorithm identifies islands and marks them. This report describes in detail the development of these three algorithms. Examples of imagery are used throughout the paper to illustrate the various steps in algorithms. Actual code is included in appendices. The algorithms presented are preliminary versions that can be applied to automatic coastline detection in SAR imagery. There are many variations and additions to the algorithms that can be made to improve robustness and automation, as required by a particular application.

Dense systems of linear equations are quite common in many science and engineering applications. Such linear systems place extreme storage and computational demands on computer resources and, in many cases, may severely limit the subsequent analysis. A dense out-of-core solver (DOCS) that operates on a partitioned coefficient matrix can reduce the in-core storage requirements of the linear system while spreading the associated computational burden over multiple processors (which reduces run time as well). In this report, I describe a DOCS that operates on a partitioned coefficient matrix that maybe distributed over multiple external storage devices. I have implemented this solver using Message-Passing Interface (MPI) protocols. This report presents petiormance data from a series of run time trials that compare the run time of both sequential and parallel implementations of the DOCS.

The power conversion system (PCS) is a vital part of many energy storage systems. It serves as the interface between the storage device, an energy source, and an AC load. This report summarizes the results of an extensive study of state-of-the-art power conversion systems used for energy storage applications. The purpose of the study was to investigate the potential for cost reduction and performance improvement in these power conversion systems and to provide recommendations for fiture research and development. This report provides an overview of PCS technology, a description of several state-of-the-art power conversion systems and how they are used in specific applications, a summary of four basic configurations for l:he power conversion systems used in energy storage applications, a discussion of PCS costs and potential cost reductions, a summary of the stancku-ds and codes relevant to the technology, and recommendations for future research and development.

The U.S. Department of Energy (DOE) has been developing a nuclear waste disposal facility, the Waste Isolation Pilot Plant (WIPP), located approximately 42 km east of Carlsbad, New Mexico. The WIPP is designed to demonstrate the safe disposal of transuranic wastes produced by the defense nuclear-weapons program. Pefiormance assessment analyses (U.S. DOE, 1996) indicate that human intrusion by inadvertent and intermittent drilling for resources provide the only credible mechanisms for significant releases of radionuclides horn the disposal system. These releases may occur by five mechanisms: (1) cuttings, (2) cavings, (3) spallings, (4) direct brine releases, and (5) long- term brine releases. The first four mechanisms could result in immediate release of contaminant to the accessible environment. For the last mechanisq migration pathways through the permeable layers of rock above the Salado are important, and major emphasis is placed on the Culebra Member of the Rustler Formation because this is the most transmissive geologic layer in the disposal system. For reasons of initial quantity, half-life, and specific radioactivity, certain isotopes of T~ U, Am, and Pu would dominate calculated releases from the WIPP. In order to help quantifi parameters for the calculated releases, radionuclide transport experiments have been carried out using five intact-core columns obtained from the Culebra dolomite member of the Rustler Formation within the Waste Isolation Pilot Pknt (WIPP) site in southeastern New Mexico. This report deals primarily with results of analyses for 241Pu and 241Am distributions developed during transport experiments in one of these cores. All intact-core column transport experiments were done using Culebra-simukmt brine relevant to the core recovery location (the WIPP air-intake shaft - AK). Hydraulic characteristics (i.e., apparent porosity and apparent dispersion coefficient) for intact-core columns were obtained via experiments using conservative tracer `Na. Elution experiments carried out over periods of a few days with tracers `2U and `?Np indicated that these tracers were weakly retarded as indicated by delayed elution of these species. Elution experiments with tracers 24% and 24*Arn were performed, but no elution of either species was observed in any flow experiment to date, including experiments of many months' duration. In order to quanti~ retardation of the non-eluted species 24*Pu and 241Arn afler a period of brine flow, non-destructive and destructive analyses of an intact-core column were carried out to determine distribution of these actinides in the rock. Analytical results indicate that the majority of the 241Am is present very near the top (injection) surface of the core (possibly as a precipitate), and that the majority of the 241Pu is dispersed with a very high apparent retardation value. The 24]Pu distribution is interpreted using a single-porosity advection-dispersion model, and an approximate retardation value is reported for this actinide. The specific radionuclide isotopes used in these experiments were chosen to facilitate analysis. Even though these isotopes are not necessarily the same as those that are most important to WIPP performance, they are isotopes of the same elements, and their chemical and transport properties are therefore identical to those of isotopes in the inventory.

A large-scale field demonstration comparing final landfill cover designs has been constructed and is currently being monitored at Sandia National Laboratories in Albuquerque, New Mexico. Two conventional designs (a RCRA Subtitle `D' Soil Cover and a RCRA Subtitle `C' Compacted Clay Cover) were constructed side-by-side with four alternative cover test plots designed for dry environments. The demonstration is intended to evaluate the various cover designs based on their respective water balance performance, ease and reliability of construction, and cost. This paper presents an overview of the ongoing demonstration.

This report provides an overview of the results of the Vital Issues process as implemented for the Senegal Water Resources Management Initiative, a collaborative effort between the Senegalese Ministry of Water Resources and Sandia National Laboratories. This Initiative is being developed to assist in the development of an efficient and sustainable water resources management system for Senegal. The Vital Issues process was used to provide information for the development of a proposal that will recommend actions to address the key management issues and establish a state-of-the-art decision support system (DSS) for managing Senegal`s water resources. Three Vital Issues panel meetings were convened to (1) develop a goal statement and criteria for identifying and ranking the issues vital to water resources management in Senegal; (2) define and rank the issues, and (3) identify and prioritize a preliminary list of information needed to address the vital issues. The selection of panelists from the four basic institutional perspectives (government, industry, academe, and citizens` interest groups) ensured a high level of stakeholder representation on the panels.

Integrated Circuits (ICs) are being extensively used in commercial and government applications that have extreme consequences of failure. The rapid evolution of the commercial microelectronics industry presents serious technical and supplier challenges to this niche critical IC marketplace. This Roadmap was developed in conjunction with the Using ICs in Critical Applications Workshop which was held in Albuquerque, NM, November 11--12, 1997.

This report presents interpretations of hydraulic tests conducted at 15 well locations in the vicinity of the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico between 1980 and 1996. The WIPP is a US Department of Energy (DOE) facility to demonstrate safe disposal of transuranic wastes arising form the nation`s defense programs. The WIPP repository lies within bedded halite of the Salado Formation, 2,155 ft below ground surface. The tests reported herein were, with two exceptions, conducted in the Culebra Dolomite member of the Rustler Formation, which overlies the Salado Formation. The remaining tests were conducted in the Magenta Member of the Rustler and in the overlying formation, the Dewey Lake Redbeds. This report completes the documentation of hydraulic-test interpretations used as input to the WIPP Compliance Certification Application (US DOE, 1996).

This paper presents a detailed explanation of the construction of an interest enabled database, also known as a database driven web site. The data contained in the internet enabled database are impact limiter material and seal properties. The technique used in constructing the internet enabled database presented in this paper are applicable when information that is changing in content needs to be disseminated to a wide audience.

In a number of recent studies the generation of mobile protons in the buried oxide of SOI materials and in thermal oxide buried underneath a poly-Si layer has been discussed. The protons are found to be stable and can be easily rearranged by applying an electric field. The details of the hydrogen reactions leading to the generation of the mobile H{sup +} are still under investigation. In a recent work a dynamic equilibrium model was presented. The forward reaction dominates above {approximately} 500 C and the resulting H{sup +} is mobile and entrapped inside the SiO{sub 2}. The electron is donated to the Si. The H{sup 0} is likely to be formed through H{sub 2} + K {Leftrightarrow} HK + H{sup 0}, where K is a cracking site. In the same work it was shown that the reactive hydrogen species enter the oxide from the device edges. Hence, the amount of the reactive species reaching the oxide by diffusion through the Si overlayer is negligible. These results seem to contradict earlier studies where it is shown that hydrogen can easily diffuse through the top Si layer under the given experimental conditions. The authors present here new details on hydrogen diffusion and chemistry during the protonation anneal that may offer an explanation for the hydrogen diffusion paradox. The new findings suggest that reactions at the ambient/SiO{sub 2} interface play a key role.

TOUGH2 is a porous media code which is widely-used for simulating flow and transport in fractured and porous media. TOUGH2 is generally employed using REV (Representative Elementary Volume) size elements or larger volumes. However, because TOUGH2 solves mass, momentum, and energy conservation equations, it can also be used for any size volumes as long as the proper constitutive relationships are included. The present paper discusses application of TOUGH2 to pore-scale modeling of enhanced vapor diffusion in porous media, and the changes and approximations that were employed.

Sandia is a National Security Laboratory providing scientific and engineering solutions to meet national needs for both government and industry. As part of this mission, the Intelligent Systems and Robotics Center conducts research and development in robotics and intelligent machine technologies. An overview of Sandia`s mobile robotics research is provided. Recent achievements and future directions in the areas of coordinated mobile manipulation, small smart machines, world modeling, and special application robots are presented.

Intense ion beams may be the best option for an Inertial Fusion Energy (IFE) driver. While light ions may be the long-term pulsed power approach to IFE, the current economic climate is such that there is no urgency in developing fusion energy sources. Research on light ion beams at Sandia will be suspended at the end of this fiscal year in favor of z-pinches studying ICF target physics, high yield fusion, and stewardship issues. The authors document the status of light ion research and the understanding of the feasibility of scaling light ions to IFE.

The Security Systems and Technology Center at Sandia National Laboratories has for many years been involved in the development and use of vulnerability assessment and risk analysis tools. In particular, two of these tools, ASSESS and JTS, have been used extensively for Department of Energy facilities. Increasingly, Sandia has been called upon to evaluate critical assets and infrastructures, support DoD force protection activities and assist in the protection of facilities from terrorist attacks using weapons of mass destruction. Sandia is involved in many different activities related to security and force protection and is expanding its capabilities by developing new risk analysis tools to support a variety of users. One tool, in the very early stages of development, is EnSURE, Engineered Surety Using the Risk Equation. EnSURE addresses all of the risk equation and integrates the many components into a single, tool-supported process to help determine the most cost-effective ways to reduce risk. This paper will briefly discuss some of these risk analysis tools within the EnSURE framework.

Amorphous carbon (a-C) films grow via energetic processes such as pulsed-laser deposition (PLD). The cold-cathode electron emission properties of a-C are promising for flat-panel display and vacuum microelectronics technologies. These ultrahard films consist of a mixture of 3-fold and 4-fold coordinated carbon atoms, resulting in an amorphous material with diamond-like properties. The authors study the structures of a-C films grown at room temperature as a function of PLD energetics using x-ray reflectivity, Raman spectroscopy, high-resolution transmission electron microscopy, and Rutherford backscattering spectrometry. While an understanding of the electron emission mechanism in a-C films remains elusive, the onset of emission is typically preceded by conditioning where the material is stressed by an applied electric field. To simulate conditioning and assess its effect, the authors use the spatially-localized field and current of a scanning tunneling microscope tip. Scanning force microscopy shows that conditioning alters surface morphology and electronic structure. Spatially-resolved electron energy loss spectroscopy indicates that the predominant bonding configuration changes from predominantly 4-fold to 3-fold coordination.

Both fundamental and practical aspects of ceramic joining are understood well enough for many, if not most, applications requiring moderate strengths at room temperature. This paper argues that the two greatest needs in ceramic joining are for techniques to join buried interfaces by selective heating, and methods for joining ceramics for use at temperatures of 800 to 1,200 C. Heating with microwave radiation or with high-energy electron beams has been used to join buried ceramic interfaces, for example SiC to SiC. Joints with varying levels of strength at temperatures of 600 to 1,000 C have been made using four techniques: (1) transient liquid phase bonding; (2) joining with refractory braze alloys; (3) joining with refractory glass compositions; and (4) joining using preceramic polymers. Joint strengths as high as 550 MPa at 1,000 C have been reported for silicon nitride-silicon nitride bonds tested in four-point flexure.

This part of the Short Course will review the basic mechanisms for radiation effects in semiconductor devices. All three areas of radiation damage will be considered -- total dose, displacement effects, and single event effects. Each of these areas will be discussed in turn. First an overview and background will be provided on the historical understanding of the damage mechanism. Then there will be a discussion of recent enhancements to the understanding of those mechanisms and an up-to-date picture provided of the current state of knowledge. Next the potential impact of each of these damage mechanisms on devices in emerging technologies and how the mechanisms may be used to understand device performance will be described, with an emphasis on those likely to be of importance in the new millennium. Finally some additional thoughts will be presented on how device scaling expected into the next century may impact radiation hardness.

Two models are commonly used to analyze gas-phase diffusion in porous media in the presence of advection, the Advective-Dispersive Model (ADM) and the Dusty-gas Model (DGM). The ADM, which is used in TOUGH2, is based on a simple linear addition of advection calculated by Darcy`s law and ordinary diffusion using Fick`s law with a porosity-tortuosity-gas saturation multiplier to account for the porous medium. Another approach for gas-phase transport in porous media is the Dusty-Gas Model. This model applies the kinetic theory of gases to the gaseous components and the porous media (or dust) to combine transport due to diffusion and advection that includes porous medium effects. The two approaches are compared in this paper.

High-energy pulsed-power devices routinely access field strengths above those at which broad-area, cathode-initiated, high-voltage vacuum-breakdown occur (> 1e7--3e7 V/m). Examples include magnetically-insulated-transmission-lines and current convolutes, high-current-density electron and ion diodes, high-power microwave devices, and cavities and other structures for electrostatic and RF accelerators. Energy deposited in anode surfaces may exceed anode plasma thermal-desorption creation thresholds on the time-scale of the pulse. Stimulated desorption by electron or photon bombardment can also lead to plasma formation on electrode or insulator surfaces. Device performance is limited above these thresholds, particularly in pulse length and energy, by the formation and expansion of plasmas formed primarily from electrode contaminants. In-situ conditioning techniques to modify and eliminate the contaminants through multiple high-voltage pulses, low base pressures, RF discharge cleaning, heating, surface coatings, and ion- and electron-beam surface treatment allow access to new regimes of performance through control of plasma formation and modification of the plasma properties. Experimental and theoretical progress from a variety of devices and small scale experiments with a variety of treatment methods will be reviewed and recommendations given for future work.

The cis and trans isomers of bis-(triethoxysilyl)-2-butene were polymerized by the sol-gel method under various conditions. The trans isomer formed gels under all conditions. The cis isomer formed gels only under basic conditions. Under acidic conditions it formed soluble resins of molecular weight ranging from 88,000 to 180,000 Daltons. Solid state and solution {sup 29}Si NMR revealed that the trans isomer formed condensed gels, and that the resins formed by the cis isomer contained cyclic monomers and/or ordered oligomers.

Polymerizations of aryltrialkoxysilanes generally afford soluble oligomeric or polymeric aryl-substituted silsesquioxanes. This is in spite of being based on trifunctional precursors capable of forming highly crosslinked and insoluble network polymers. In this study, soluble phenyl, benzyl, and phenethyl-substituted silsesquioxane oligomers and polymers were prepared by hydrolyzing their respective triethoxysilyl precursor with water or aqueous acid. Additional samples of the polymers were prepared by heating the materials at 100 C or 200 C under vacuum in order to drive the condensation chemistry. One sample of polybenzylsilsesquioxane was heated at 200 C with catalytic NaOH. The resulting materials were characterized using solution {sup 1}H, {sup 13}C, and {sup 29}Si NMR spectroscopy, gel permeation chromatography, and differential scanning calorimetry. Of particular interest was the effect of the aryl substituent, and processing conditions on the molecular weight and glass transition temperatures of the polysilsesquioxanes.

In May of 1998, a technical basis and implementation guidelines document for A Technique for Human Event Analysis (ATHEANA) was issued as a draft report for public comment (NUREG-1624). In conjunction with the release of the draft NUREG, a paper review of the method, its documentation, and the results of an initial test of the method was held over a two-day period in Seattle, Washington, in June of 1998. Four internationally-known and respected experts in human reliability analysis (HRA) were selected to serve as the peer reviewers and were paid for their services. In addition, approximately 20 other individuals with an interest in HRA and ATHEANA also attended the peer review meeting and were invited to provide comments. The peer review team was asked to comment on any aspect of the method or the report in which improvements could be made and to discuss its strengths and weaknesses. All of the reviewers thought the ATEANA method had made significant contributions to the field of PRA/HRA, in particular by addressing the most important open questions and issues in HRA, by attempting to develop an integrated approach, and by developing a framework capable of identifying types of unsafe actions that generally have not been considered using existing methods. The reviewers had many concerns about specific aspects of the methodology and made many recommendations for ways to improve and extend the method, and to make its application more cost effective and useful to PRA in general. Details of the reviewers` comments and the ATHEANA team`s responses to specific criticisms will be discussed.

Gas guns and velocity interferometric techniques have been used to determine the loading behavior of AD995 alumina rods 19 mm in diameter by 75 mm and 150 mm long, respectively. Graded-density materials were used to impact both bare and sleeved alumina rods while the velocity interferometer was used to monitor the axial-velocity of the free end of the rods. Results of these experiments demonstrate that (1) a time-dependent stress pulse generated during impact allows an efficient transition from the initial uniaxial strain loading to a uniaxial stress state as the stress pulse propagates through the rod, and (2) the intermediate loading rates obtained in this configuration lie between split Hopkinson bar and shock-loading techniques.

Technology roadmaps serve as pathways to the future. They call attention to future needs for research and development; provide a structure for organizing technology forecasts and programs; and help communicate technological needs and expectations among end users and the research and development (R and D) community. Critical Technology roadmaps, of which the Robotics and Intelligent Machines (RIM) Roadmap is one example, focus on enabling or cross-cutting technologies that address the needs of multiple US Department of Energy (DOE) offices. Critical Technology roadmaps must be responsive to mission needs of the offices; must clearly indicate how the science and technology can improve DOE capabilities; and must describe an aggressive vision for the future of the technology itself. The RIM Roadmap defines a DOE research and development path for the period beginning today, and continuing through the year 2020. Its purpose is to identify, select and develop objectives that will satisfy near- and long-term challenges posed by DOE`s mission objectives. If implemented, this roadmap will support DOE`s mission needs while simultaneously advancing the state-of-the-art of RIM. For the purposes of this document, RIM refers to systems composed of machines, sensors, computers and software that deliver processes to DOE operations. The RIM Roadmap describes how such systems will revolutionize DOE processes, most notably manufacturing, hazardous and remote operations, and monitoring and surveillance. The advances in DOE operations and RIM discussed in this document will be possible due to the developments in many other areas of science and technology, including computing, communication, electronics and micro-engineering. Modern software engineering techniques will permit the implementation of inherently safe RIM systems that will depend heavily on software.

An electrochemical cell suitable for in-situ XRD analysis is presented. Qualitative information such as phase formation and phase stability can be easily monitored using the in-situ cell design. Quantitative information such as lattice parameters and kinetic behavior is also straightforward. Analysis of the LiMn&sub2;O&sub4; spinel using this cell design shows that the lattice undergoes two major structural shrinkages at approx. 4.0 V and approx. 4.07 V during charging. These shrinkages correlate well with the two electrochemical waves observed and indicate the likelihood of two separate redox processes which charging and discharging.

The rate at which a mine detection system falsely identifies man-made or natural clutter objects as mines is referred to as the system's false alarm rate (FAR). Generally expressed as a rate per unit area or time, the FAR is one of the primary metrics used to gauge system performance. In this report, an overview is given of statistical methods appropriate for the analysis of data relating to FAR. Techniques are presented for determining a suitable size for the clutter collection area, for summarizing the performance of a single sensor, and for comparing different sensors. For readers requiring more thorough coverage of the topics discussed, references to the statistical literature are provided. A companion report addresses statistical issues related to the estimation of mine detection probabilities.

Abstract not provided.

There are many potential benefits to be gained from the aeroelastic behavior of a wind-turbine blade with bend-twist coupling. However, the ability to manufacture blades with sufficient coupling to provide the desired benefits has yet to be established. This report investigates the feasible (or practical) range of the coupling coefficient that can be obtained on a uniform cross-section composite D-spar, which could be the backbone of a wind-turbine-blade. The most critical parameters are identified and studied across a range of possible values. Various features, such as the geometry, skin thickness, ply distribution, ply materials, and ply orientations, are evaluated for their effect on twist-bend coupling of a D-spar. It is found that sufficient coupling can be built into the D-spar shape, but that carbon-fiber composite plies angled between 15 and 30 degrees to the longitudinal axis may be required.

Sandia National Laboratories (SNL) operates the Tonopah Test Range for the Department of Energy's (DOE) Weapons Ordnance Program. Thes annual report (calendar year 1997) summarizes the compliance status to environmental regulations applicable at the site including those statutes that govern air and water quality, waste management, cleanup of contaminated areas, control of toxic substances, and adherence to requirements as related to the National Environmental Policy Act. In compliance with DOE orders, SNL also conducts environmental surveillance for radiological and nonradiological contaminants. SNL's responsibility for environmental surveillance extends only to those activities performed by SNL or under its direction. Annual radiological and nonradiological routine releases and unplanned releases (occurrences) are also summarized. This report has been prepared as required by DOE Order 5400.1, General Environmental Protection Program.

We have reviewed ten major public problems challenging our Nation as it enters the new millennium. These are defense, healthcare costs, education, aging population, energy and environment, crime, low productivity growth services, income distribution, regulations, and infrastructure. These problems share several features. First, each is so large, if it were soIved; it would have major impact on the U.S. economy. Second, each is resident in a socioeconomic system containing non-linear feedback loops and an adaptive human element. Third, each can only be solved by our political system, yet these problems are not responsive to piecemeal problem solving, the approach traditionally used by policy makers. However, unless each problem is addressed in the context of the system in which it resides, the solution maybe worse than the problem. Our political system is immersed in reams of disconnected, unintelligible information skewed by various special interests to suggest policies favoring their particular needs. Help is needed, if rational solutions that serve public interests are to be forged for these ten probIems, The simulation and modeIing tools of physical scientists, engineers, economists, social scientists, public policy experts, and others, bolstered by the recent explosive growth in massively parallel computing power, must be blended together to synthesize models of the complex systems in which these problems are resident. These models must simulate the seemingly chaotic human element inherent in these systems and support policymakers in making informed decKlons about the future. We propose altering the policy development process by incorporating more modeling, simulation and analysis to bring about a revolution in policy making that takes advantage of the revolution in engineering emerging from simulation and modeling. While we recommend major research efforts to address each of these problems, we also observe these to be very complex, highly interdependent, multi-disciplinary problems; it will challenge the U.S. community of individual investigator researchers to make the cultural transformation necessary to address these problems in a team environment. Furthermore, models that simulate future behavior of these complex systems will not be exacq therefore, researchers must be prepared to use the modeling and simulation tools they develop to propose experiments to Congress. We recommend that ten laboratories owned by the American public be selected in an interagency competition to each manage and host a $1 billion/yertr National effort, each focused on one of these ten problems. Much of the supporting research and subsystem modeling work will be conducted at U.S. universities and at private firms with relevant expertise. Success of the Manhattan Project at the middle of the 20th century provides evidence this leadership model works.

The problem of combining multi-source information in applications related to automatic target recognition (ATR) is addressed. A mathematical approach is proposed for fusing the (possibly dependent) outputs of multiple ATR systems or algorithms. The method is derived from statistical principles, and the fused decision takes the form of an hypothesis test. The distribution of the test statistic is approximated as gamma, with parameters estimated from available training data. In a brief simulation study, the proposed method outperforms several alternative fusion techniques.

In-situ barrier emplacement techniques and materials for the containment of high-risk contaminants in soils are currently being developed by the Department of Energy (DOE). Because of their relatively high cost, the barriers are intended to be used in cases where the risk is too great to remove the contaminants, the contaminants are too difficult to remove with current technologies, or the potential movement of the contaminants to the water table is so high that immediate action needs to be taken to reduce health risks. Assessing the integrity of the barrier once it is emplaced, and during its anticipated life, is a very difficult but necessary requirement. Science and Engineering Associates, Inc., (SEA) and Sandia National Laboratories (SNL) have developed a quantitative subsurface barrier assessment system using gaseous tracers in support of the Subsurface Contaminants Focus Area barrier technology program. Called SEAtrace{trademark}, this system integrates an autonomous, multi-point soil vapor sampling and analysis system with a global optimization modeling methodology to locate and size barrier breaches in real time. The methodology for the global optimization code was completed and a prototype code written using simplifying assumptions. Preliminary modeling work to validate the code assumptions were performed using the T2VOC numerical code. A multi-point field sampling system was built to take soil gas samples and analyze for tracer gas concentration. The tracer concentration histories were used in the global optimization code to locate and size barrier breaches. SEAtrace{trademark} was consistently able to detect and locate leaks, even under very adverse conditions. The system was able to locate the leak to within 0.75 m of the actual value, and was able to determine the size of the leak to within 0.15 m.

This report presents a comparison of life cycle costs between battery energy storage systems and alternative mature technologies that could serve the same utility-scale applications. Two of the battery energy storage systems presented in this report are located on the supply side, providing spinning reserve and system stability benefits. These systems are compared with the alternative technologies of oil-fired combustion turbines and diesel generators. The other two battery energy storage systems are located on the demand side for use in power quality applications. These are compared with available uninterruptible power supply technologies.

A system based on the metal-binding kidney protein, metallothionein, bound with a trace quantity of radioactive metal, has been shown to be capable of detecting parts-per-million (ppm) to parts-per-billion (ppb) concentrations of some heavy metals in liquid solution. The main objective of this study was to determine if this type of system has adequate sensitivity and selectivity for application in detecting a number of metallic species of concern to DOE, such as mercury, lead, and chromium. An affinity-displacement study is reported here using the heavy metal radiotracers {sup 65}Zn and {sup 109}Cd bound to metallothionein immobilized on an Affi-Gel 10 filter support. When a heavy metal solution with a greater affinity than the tracer for the protein is poured through the filter the radiotracer is displaced by a mechanism similar to ion exchange. The main objective of this study was to verify previous internal experimental parameters and results, and to determine the specific affinities of metallothionein for the metallic species of most concern to DOE.