Publications

We show that Sorensen's [35] implicitly restarted Arnoldi method (including its block extension) is simultaneous iteration with an implicit projection step to accelerate convergence to the invariant subspace of interest. By using the geometric convergence theory for simultaneous iteration due to Watkins and Elsner [43], we prove that an implicitly restarted Arnoldi method can achieve a super-linear rate of convergence to the dominant invariant subspace of a matrix. Moreover, we show how an IRAM computes a nested sequence of approximations for the partial Schur decomposition associated with the dominant invariant subspace of a matrix.

Screening of sites for the potential application and reliance upon monitored natural attenuation (MNA) can be done using MNAtoolbox, a web-based tool for estimating extent of biodegradation, chemical transformation, and dilution. MNAtoolbox uses site-specific input data, where available (default parameters are taken from the literature), to roughly quantify the nature and extent of attenuation at a particular site. Use of MNAtoolbox provides 3 important elements of site evaluation: (1) Identifies likely attenuation pathways, (2) Clearly identifies sites where MNA is inappropriate, and (3) Evaluates data requirements for subsequent reliance on MNA as a sole or partial corrective action.

Sandia National Laboratories (SNL) and the Russian Federal Nuclear Center-All Russian Research Institute for Experimental Physics (VNIIEF)(also know as Arzamas-16) are collaborating on ways to assure the highest standards on safety, security, and international accountability of fissile material. This includes systems used to reduce the need for human access to fissile material, reduce radiation exposure, and provide prompt safety-related information, and provide continuous international accountability information while reducing the need for intrusive, on-site visits. This paper will report on the ongoing SNL/VNIIEF efforts to develop technologies and monitoring systems to meet these goals. Specific topics covered will include: the Smart Bolt tag/seal development, development and testing of electronic sensor platforms (U.S. T-1 ESP and VNIIEF Radio Tag) for monitoring and transportation applications, the ''Magazine-to-Magazine'' remote monitoring system field test, and the ''Facility-to-Facility'' storage monitoring system field trial.

Abstract not provided.

A new forcefield model was developed for the computer simulation of phosphate materials that have many important applications in the electronics and biomedical industries. The model provides a fundamental basis for the evaluation of phosphate glass structure and thermodynamics. Molecular dynamics simulations of a series of lithium phosphate glass compositions were performed using the forcefield model. A high concentration of three-membered rings (P{sub 3}O{sub 3}) occurs in the glass of intermediate composition (0.2 Li{sub 2}O {center_dot} 0.8P{sub 2}O{sub 5}) that corresponds to the minimum in the glass transition temperature curve for the compositional series. Molecular orbital calculations of various phosphate ring clusters indicate an increasing stabilization of the phosphate ring structure going from two- to four-membered rings.

A new approach is being pursued to study corrosion in Cu alloy systems by using combinatorial analysis combined with microscopic experimentation (the Combinatorial Microlab) to determine mechanisms for copper corrosion in air. Corrosion studies are inherently difficult because of complex interactions between materials and environment, forming a multidimensional phase space of corrosion variables. The Combinatorial Microlab was specifically developed to address the mechanism of Cu sulfidation, which is an important reliability issue for electronic components. This approach differs from convention by focusing on microscopic length scales, the relevant scale for corrosion. During accelerated aging, copper is exposed to a variety of corrosive environments containing sulfidizing species that cause corrosion. A matrix experiment was done to determine independent and synergistic effects of initial Cu oxide thickness and point defect density. The CuO{sub x} was controlled by oxidizing Cu in an electron cyclotron resonance (ECR) O{sub 2} plasma, and the point defect density was modified by Cu ion irradiation. The matrix was exposed to 600 ppb H{sub 2}S in 65% relative humidity air atmosphere. This combination revealed the importance of oxide quality in passivating Cu and prevention of the sulfidizing reaction. A native oxide and a defect-laden ECR oxide both react at 20 C to form a thick Cu{sub 2}S layer after exposure to H{sub 2}S, while different thicknesses of as-grown ECR oxide stop the formation of Cu{sub 2}S. The species present in the ECR oxide will be compared to that of an air oxide, and the sulfide layer growth rate will be presented.

We describe highly anisotropic reactive ion beam etching of nanophotonic structures in AlGaAs based on the ion beam divergence angle and chamber pressure. The divergence angle is shown to influence the shape of the upper portion of the etch while the chamber pressure controls the shape of the lower portion. This predictable region of parameter space resulted in highly anisotropic nanostructures. Deeply etched distributed Bragg reflectors are etched to an aspect ratio of 8:1 with 100 nm trench widths. The profile of the grating etch is straight with smooth sidewalls, flat bottoms, and squared corners. Two-dimensional photonic crystal post arrays are fabricated with smooth and vertical sidewalls, with structures as small as 180 nm in diameter and 2.0 {micro}m in height.

RF and mm-wave photonic devices and circuits have been developed at Sandia National Laboratories for applications ranging from RF optical data links to optical generation of mm-wave frequencies. This talk will explore recent high-speed photonics technology developments at Sandia including: (1) A monolithic optical integrated circuit for all-optical generation of mm-waves. Using integrated mode-locked diode lasers, amplifiers, and detectors, frequencies between 30 GHz and 90 GHz are generated by a single monolithic (Al,Ga)As optical circuit less than 2mm in its largest dimension. (2) Development of polarization-maintaining, low-insertion-loss, low v-pi, Mach-Zehnder interferometer (MZI) modulators with DC-to-potentially-K-band modulation bandwidth. New low-loss polarization-maintaining waveguide designs using binary alloys have been shown to reduce polarization crosstalk in undoped (Al,Ga)As waveguides, yielding high extinction ratio (>40dB) and low on-chip loss (<6dB) in Mach-Zehnder interferometers. RF drive voltage is reduced through use of 45rnrn-active length devices with modulator sensitivity, v-pi, less than 3V.

Recently, Morel and McGhee described an alternate second-order form of the transport equation called the self adjoint angular flux (SAAF) equation that has the angular flux as its unknown. The SAAF formulation has all the advantages of the traditional even- and odd-parity self-adjoint equations, with the added advantages that it yields the full angular flux when it is numerically solved, it is significantly easier to implement reflective and reflective-like boundary conditions, and in the appropriate form it can be solved in void regions. The SAAF equation has the disadvantage that the angular domain is the full unit sphere and, like the even- and odd- parity form, S{sub n} source iteration cannot be implemented using the standard sweeping algorithm. Also, problems arise in pure scattering media. Morel and McGhee demonstrated the efficacy of the SAAF formulation for neutral particle transport. Here we apply the SAAF formulation to coupled electron-photon transport problems using multigroup cross-sections from the CEPXS code and S{sub n} discretization.

The integration of miniaturized mechanical components has spawned a new technology known as microelectromechanical systems (MEMS). Surface micromachining, defined as the fabrication of micromechanical structures from deposited thin films, is one of the core technological processes underlying MEMS. Surface micromachined structures have a large ratio of surface area to volume which makes them particularly vulnerable to adhesion to the substrate or adjacent structures during release or in use--a problem is called stiction. Since microactuators can have surfaces in normal or sliding contact, function and wear are critical issues for reliable operation of MEMS devices. Surface modifications are needed to reduce adhesion and friction in micromechanical structures. In this paper, we will present a process used to selectively coat MEMS devices with Tungsten using a CVD (Chemical Vapor Deposition) process. We will discuss the effect of wet and vapor phase cleans along with different process variables. Endurance of the W coating is important, especially in applications where wear due to repetitive contacts with the film may occur. Further, tungsten is hard and chemically inert, Tungsten CVD is used in the integrated-circuit industry, which makes this, approach manufacturable.

Microfabrication technology has been applied to the development of a miniature, multi-channel gas phase chemical laboratory that provides fast response, small size, and enhanced versatility and chemical discrimination. Each analysis channel includes a sample concentrator followed by a gas chromatographic separator and a chemically selective surface acoustic wave detector array to achieve high sensitivity and selectivity. The performance of the components, individually and collectively, is described. The design and performance of novel micromachined acoustic wave devices, with the potential for improved chemical sensitivity, are also described.

The authors present prism coupling measurements on Al{sub x}Ga{sub 1{minus}x}As native oxides showing the dependence of refractive index on composition (0.3 {le} x {le} 0.97), oxidation temperature (400 {le} T {le} 500), and carrier gas purity. Index values range from n = 1.490 (x = 0.9, 400) to 1.707 (x = 0.3, 500 C). The oxides are shown to adsorb moisture, increasing their index by up to 0.10 (7%). Native oxides of Al{sub x}Ga{sub 1{minus}x}As (x {le} 0.5) have index values up to 0.27 higher and are less hygroscopic when prepared with a small amount of O{sub 2} in the N{sub 2} + H{sub 2}O process gas. The higher index values are attributed to a greater degree of oxidation of the Ga in the film.

In a quantum grid infrared photodetector (QGIP), the active multiple quantum well material is patterned into a grid structure. The purposes of the grid are on the one hand to create additional lateral electron confinement and on the other to convert part of the incident light into parallel propagation. With these two unique functions, a QGIP allows intersubband transition to occur in all directions. In this work, we focused on improving the effectiveness of a QGIP in redirecting the propagation of light using a blazed structure. The optimization of the grid parameters in terms of the blaze angle and the periodicity was performed by numerical simulation using the modal transmission-line theory and verified by experiment. With a blazed structure, the sensitivity of a QGIP can be improved by a factor of 1.8 compared with a regular QGIP with rectangular profiles.

Using Interracial Force Microscopy (IFM), we investigated the tribological behavior of hexadecanethiol monolayer on Au and films of octadecyltrichlorosilane (ODTS), perfluorodecyltrichlorosilane (PFTS) and dodecane on Si. We observe a strong correlation between hysteresis in a compression cycle (measured via nanoindentation) and friction. Additionally, we suggest that the amount of hysteresis and friction in each film is related to its detailed molecular structure, especially the degree of molecular packing.

The Geothermal Drilling Organization (GDO), founded in 1982 as a joint Department of Energy (DOE)-Industry organization, develops and funds near-term technology development projects for reducing geothermal drilling costs. Sandia National Laboratories administers DOE funds to assist industry critical cost-shared projects and provides development support for each project. GDO assistance to industry is vital in developing products and procedures to lower drilling costs, in part, because the geothermal industry is small and represents a limited market.

Energy (DOE)-industry research and development (R and D) organization, sponsors near-term technology development projects for reducing geothermal drilling and well maintenance costs. Sandia National Laboratories (Albuquerque, NM) administers DOE funds for GDO cost-shared projects and provides technical support. The GDO serves a very important function in fostering geothermal development. It encourages commercialization of emerging, cost-reducing drilling technologies, while fostering a spirit of cooperation among various segments of the geothermal industry. For Sandia, the GDO also serves as a means of identifying the geothermal industry's drilling fuel/or well maintenance problems, and provides an important forum for technology transfer. Successfully completed GDO projects include: the development of a high-temperature borehole televiewer, high-temperature rotating head rubbers, a retrievable whipstock, and a high-temperature/high-pressure valve-changing tool. Ongoing GDO projects include technology for stemming lost circulation; foam cement integrity log interpretation, insulated drill pipe, percussive mud hammers for geothermal drilling, a high-temperature/ high-pressure valve changing tool assembly (adding a milling capability), deformed casing remediation, high- temperature steering tools, diagnostic instrumentation for casing in geothermal wells, and elastomeric casing protectors.

The increased demand for portable electronics has lead to the need for higher performance and efficiency. Devices operating at less than 50 {micro}W of power are defined as ultra-low-power (ULP) devices. New progress has been achieved on InP/InGaAs HBT and InAIAs/InGaAs HBT optimized for ULP applications. f{sub T} values of 2.2 GHz, and f{sub MAX} values of 20 GHz have been obtained for HBTs operating at less than 40 {micro}W. Current gain is greater than 45 with the device operating at less than 20 {micro}A on a 2.5 x 5 {micro}m{sup 2} device. These devices have been significantly improved over the previously reported MOCVD grown InP/InGaAs ULP HBT which has f{sub MAX} of 10 GHz operating in the ultra-low-power level. The improvements have been attributed to the reduction of base dopant diffusion associated with Zn doping.

MTI is a comprehensive research and development project that includes up-front modeling and analysis, satellite system design, fabrication, assembly and testing, on-orbit operations, and experimentation and data analysis. The satellite is designed to collect radiometrically calibrated, medium resolution imagery in 15 spectral bands ranging from 0.45 to 10.70 pm. The payload portion of the satellite includes the imaging system components, associated electronics boxes, and payload support structure. The imaging system includes a three-mirror anastigmatic off-axis telescope, a single cryogenically cooled focal plane assembly, a mechanical cooler, and an onboard calibration system. Payload electronic subsystems include image digitizers, real-time image compressors, a solid state recorder, calibration source drivers, and cooler temperature and vibration controllers. The payload support structure mechanically integrates all payload components and provides a simple four point interface to the spacecraft bus. All payload components have been fabricated and tested, and integrated.

This project has comprised design, analysis, laboratory testing, and field testing of insulated drill pipe (IDP). This paper will briefly describe the earlier work, but will focus on results from the recently-completed field test in a geothermal well. Field test results are consistent with earlier analyses and laboratory tests, all of which support the conclusion that insulated drill pipe can have a very significant effect on circulating fluid temperatures. This will enable the use of downhole motors and steering tools in hot wells, and will reduce corrosion, deterioration of drilling fluids, and heat-induced failures in other downhole components.

GaN Schottky diodes were exposed to N₂ or H₂ Inductively Coupled Plasmas prior to deposition of the rectifying contact. Subsequent annealing, wet photochemical etching or (NH₄)₂S surface passivation treatments were examined for their effect on diode current- voltage characteristics. We found that either annealing at 750 °C under N₂, or removal of ~500-600 Å of the surface essentially restored the initial I-V characteristics. There was no measurable improvement in the plasma-exposed diode behavior with (NH₄)₂S treatments.

We analyze the transverse profiles of oxide-confined vertical cavity laser diodes as a function of aperture size. For small apertures we demonstrate that thermal lensing can be the dominant effect in determining the transverse resonator properties. We also analyze pattern formation in lasers with large apertures where we observe the appearance of tilted waves.

The goal of the Russian Navy Fuels Program is to incorporate nuclear fuel that is in the custody of the Russian Navy into a materials protection, control and accounting program. In addition to applying MPC and A upgrades to existing facilities, a program is underway to train site personnel in MPC and A activities. The goal is to assure that the upgraded facilities are managed, operated and maintained in an effective, sustainable manner. Training includes both the conceptual and necessary operational aspects of the systems and equipment. The project began with a Needs Assessment to identify priorities and objectives of required training. This led to the creation of a series of classes developed by Kurchatov Institute. One course was developed to allow attendees to get a general understanding of goals and objectives of nuclear MPC and A systems in the context of the Russian Navy. A follow-on course provided the detailed skills necessary for the performance of specialized duties. Parallel sessions with hands-on exercises provided the specific training needed for different personnel requirements. The courses were presented at KI facilities in Moscow. This paper reviews the work to date and future plans for this program.

Various efforts to map the structure of science have been undertaken over the years. Using a new tool, VxInsight{trademark}, we have mapped and displayed 3000 journals in the physical sciences. This map is navigable and interactively reveals the structure of science at many different levels. Science mapping studies are typically focused at either the macro-or micro-level. At a macro-level such studies seek to determine the basic structural units of science and their interrelationships. The majority of studies are performed at the discipline or specialty level, and seek to inform science policy and technical decision makers. Studies at both levels probe the dynamic nature of science, and the implications of the changes. A variety of databases and methods have been used for these studies. Primary among databases are the citation indices (SCI and SSCI) from the Institute for Scientific Information, which have gained widespread acceptance for bibliometric studies. Maps are most often based on computed similarities between journal articles (co-citation), keywords or topics (co-occurrence or co-classification), or journals (journal-journal citation counts). Once the similarity matrix is defined, algorithms are used to cluster the data.

Thermally-Induced Voltage Alteration (TIVA) and Seebeck Effect Imaging (SEI) are newly developed techniques for localizing shorted and open conductors from the front and backside of an IC. Recent improvements have greatly increased the sensitivity of the TIVA/SEI system, reduced the acquisition times by more than 20X, and localized previously unobserved defects. The system improvements, non-linear response of IC defects to heating, modeling of laser heating and examples using the improved system are presented.

Performance tests of a scaled passive autocatalytic recombine (PAR) were performed in the Surtsey test vessel at Sandia National Laboratories. Measured hydrogen depletion rate data were obtained and compared with previous work. Depletion rate is most likely proportional to PAR scale. PAR performance in steamy environments (with and without hydrophobic coating) was investigated. The tests determined that the PAR startup delay times decrease with increasing hydrogen concentrations in steamy environments. Tests with placement of the PAR near a wall (as opposed to a center location) yielded reduced depletion rates. Tests at low oxygen concentrations also showed a reduced recombination rate. The PAR repeatedly ignited hydrogen at about 6 mol% concentration with a catalyst temperature near 940 K. Velocity data at the PAR exhaust were used to calculate the volumetric flow rate through the PAR as a function of the vessel hydrogen concentration.

Multivariate techniques were used to address the quantification of {sup 17}O-NMR (nuclear magnetic resonance) spectra for a series of primary alcohol mixtures. Due to highly overlapping resonances, quantitative spectral evaluation using standard integration and deconvolution techniques proved difficult. Multivariate evaluation of the {sup 17}O-NMR spectral data obtained for 26 mixtures of five primary alcohols demonstrated that obtaining information about spectral overlap and interferences allowed the development of more accurate models. Initial partial least squares (PLS) models developed for the {sup 17}O-NMR data collected from the primary alcohol mixtures resulted in very poor precision, with signal overlap between the different chemical species suspected of being the primary contributor to the error. To directly evaluate the question of spectral overlap in these alcohol mixtures, net analyte signal (NAS) analyses were performed. The NAS results indicate that alcohols with similar chain lengths produced severely overlapping {sup 17}O-NMR resonances. Grouping the alcohols based on chain length allowed more accurate and robust calibration models to be developed.

This report describes an inert atmosphere enclosed gas-tungsten arc welding system which has been assembled in support of the MC2730, MC2730A and MC 3500 Radioisotope Thermoelectric Generator (RTG) Enhanced Surveillance Program. One goal of this program is to fabricate welds with microstructures and impurity levels which are similar to production heat source welds previously produced at Los Alamos National Laboratory and the Mound Facility. These welds will subsequently be used for high temperature creep testing as part of the overall component lifetime assessment. In order to maximize the utility of the welding system, means for local control of the arc atmosphere have been incorporated and a wide range of welding environments can easily be evaluated. The gas-tungsten arc welding system used in the assembly is computer controlled, includes two-axis and rotary motion, and can be operated in either continuous or pulsed modes. The system can therefore be used for detailed research studies of welding impurity effects, development of prototype weld schedules, or to mimic a significant range of production-like welding conditions. Fixturing for fabrication of high temperature creep test samples have been designed and constructed, and weld schedules for grip-tab and test welds have been developed. The microstructure of these welds have been evaluated and are consistent with those used during RTG production.

This report represents the completion of a 6 month Laboratory-Directed Research and Development (LDRD) program that focused on research and development of novel compound semiconductor, InGaAsN. This project seeks to rapidly assess the potential of InGaAsN for improved high-efficiency photovoltaic. Due to the short time scale, the project focused on quickly investigating the range of attainable compositions and bandgaps while identifying possible material limitations for photovoltaic devices. InGaAsN is a new semiconductor alloy system with the remarkable property that the inclusion of only 2% nitrogen reduces the bandgap by more than 30%. In order to help understand the physical origin of this extreme deviation from the typically observed nearly linear dependence of alloy properties on concentration, we have investigated the pressure dependence of the excited state energies using both experimental and theoretical methods. We report measurements of the low temperature photoluminescence energy of the material for pressures between ambient and 110 kbar. We describe a simple, density-functional-theory-based approach to calculating the pressure dependence of low lying excitation energies for low concentration alloys. The theoretically predicted pressure dependence of the bandgap is in excellent agreement with the experimental data. Based on the results of our calculations, we suggest an explanation for the strongly non-linear pressure dependence of the bandgap that, surprisingly, does not involve a nitrogen impurity band. Additionally, conduction-band mass measurements, measured by three different techniques, will be described and finally, the magnetoluminescence determined pressure coefficient for the conduction-band mass is measured. The design, growth by metal-organic chemical vapor deposition, and processing of an In{sub 0.07}Ga{sub 0.93}As{sub 0.98}N{sub 0.02} solar cell, with 1.0 eV bandgap, lattice matched to GaAs is described. The hole diffusion length in annealed, n-type InGaAsN is 0.6-0.8 pm, and solar cell internal quantum efficiencies >70% are obtained. Optical studies indicate that defects or impurities, from doping and nitrogen incorporation, limit cell performance.

Selective oxidation of AlGaAs compounds has facilitated dramatic improvements in the performance of near IR VCSELS. Under the auspices of this proposal we have: (1) expanded our understanding of both the strengths and the limitations of this technology; (2) explored its applicability to other Al bearing materials; (3) utilized this technology base to demonstrate a variety of new electronic and optoelectronic devices; and (4) established the reliability and manufacturability of oxidized devices such as VCSELS. Specifically, we have investigated conditions required to maximize control of the oxidation process as well as those required to facilitate inhibit etching of the resultant oxide. Concurrently, studies were performed to extend the technology to other Al-bearing compounds such as Al(Ga)AsSb, InAl(Ga)P and Al(Ga)N. Several new devices utilizing the selective oxidation technology of AlGaAs, as well as Al(Ga)AsSb were be considered. On a separate front, we also explored the possibility of using oxidized AlGaAs and InAl(Ga)P to form GaAs/AIGaAs FETs. Finally, reliability and manufacturability issues of the high performance VCSELS fabricated using selective oxidation technology, were addressed.

The series of tests described in this report are intended to simulate actual use and abuse conditions and internally initiated failures that may be experienced in electrochemical storage systems (ECSS). These tests were derived from Failure Mode and Effect Analysis, user input, and historical abuse testing. The tests are to provide a common framework for various ECSS technologies. The primary purpose of testing is to gather response information to external/internal inputs. Some tests and/or measurements may not be required for some ECSS technologies and designs if it is demonstrated that a test is not applicable, and the measurements yield no useful information.

The elevation change data measured at the Bryan Mound Strategic Petroleum Reserve (SPR) site over the last 16+ years has been studied and a model utilized to project elevation changes into the future. The subsidence rate at Bryan Mound is low in comparison with other Strategic Petroleum Reserve sites and has decreased with time due to the maintenance of higher operating pressures and the normal decrease in creep closure rate of caverns with time. However, the subsidence at the site is projected to continue. A model was developed to project subsidence values 20 years into the future; no subsidence related issues are apparent from these projections.

Fifteen aluminum honeycomb cubes (3 in.) have been crushed in the Mechanical Shock Laboratory's drop table testing machines. This report summarizes shock experiments with honeycomb densities of 22.1 pcf and 38.0 pcf and with crush weights of 45 lb, 168 lb, and 268 lb. The honeycomb samples were crushed in all three orientations, W, L, and T. Most of the experiments were conducted at an impact velocity of {approx}40 fps, but higher velocities of up to 90 fps were used for selected experiments. Where possible, multiple experiments were conducted for a specific orientation and density of the honeycomb samples. All results are for Hexcel honeycomb except for one experiment with Alcore honeycomb and have been evaluated for validity. This report contains the raw acceleration data measured on the top of the drop table carriage, pictures of the crushed samples, and normalized force-displacement curves for all fifteen experiments. These data are not strictly valid for material characteristics in L and T orientations because the cross-sectional area of the honeycomb changed (split) during the crush. However, these are the best data available at this time. These dynamic crush data do suggest a significant increase in crush strength to 8000 psi ({approximately} 25-30% increase) over quasi-static values of {approximately}6000 psi for the 38.0 pcf Hexcel Honeycomb in the T-orientation. An uncertainty analysis is included and estimates the error in these data.

The Zinc/Bromine Load-Leveling Battery Development contract (No. 40-8965) was partitioned at the outset into two phases of equal length. Phase 1 started in September 1990 and continued through December 1991. In Phase 1, zinc/bromine battery technology was to be advanced to the point that it would be clear that the technology was viable and would be an appropriate choice for electric utilities wishing to establish stationary energy-storage facilities. Criteria were established that addressed most of the concerns that had been observed in the previous development efforts. The performances of 8-cell and 100-cell laboratory batteries demonstrated that the criteria were met or exceeded. In Phase 2, 100-kWh batteries will be built and demonstrated, and a conceptual design for a load-leveling plant will be presented. At the same time, work will continue to identify improved assembly techniques and operating conditions. This report details the results of the efforts carried out in Phase 1. The highlights are: (1) Four 1-kWh stacks achieved over 100 cycles, One l-kWh stack achieved over 200 cycles, One 1-kWh stack achieved over 300 cycles; (2) Less than 10% degradation in performance occurred in the four stacks that achieved over 100 cycles; (3) The battery used for the zinc loading investigation exhibited virtually no loss in performance for loadings up to 130 mAh/cm{sup 2}; (4) Charge-current densities of 50 ma/cm{sup 2} have been achieved in minicells; (5) Fourteen consecutive no-strip cycles have been conducted on the stack with 300+ cycles; (6) A mass and energy balance spreadsheet that describes battery operation was completed; (7) Materials research has continued to provide improvements in the electrode, activation layer, and separator; and (8) A battery made of two 50-cell stacks (15 kWh) was produced and delivered to Sandia National Laboratories (SNL) for testing. The most critical development was the ability to assemble a battery stack that remained leak free. The task of sealing the battery stack using vibration welding has undergone significant improvement resulting in a viable production process. Through several design iterations, a solid technology base for larger battery stack designs was established. Internal stack stresses can now be modeled, in addition to fluid velocity and fluid pressure distribution, through the use of a finite element analysis computer program. Additionally, the Johnson Controls Battery Group, Inc. (JCBGI) proprietary FORTRAN model has been improved significantly, enabling accurate performance predictions. This modeling was used to improve the integrity and performance of the battery stacks, and should be instrumental in reducing the turnaround time from concept to assembly.

This report presents interpretations of hydraulic tests conducted in bedded evaporates of the Salado Formation from May 1992 through May 1995 at the Waste Isolation Pilot Plant (WIPP) site in southeastern New Mexico. The WIPP is a US Department of Energy research and development facility designed to demonstrate safe disposal of transuranic wastes from the nation's defense programs. The WIPP disposal horizon is located in the lower portion of the Permian Salado Formation. The hydraulic tests discussed in this report were performed in the WIPP underground facility by INTERA inc. (now Duke Engineering and Services, Inc.), Austin, Texas, following the Field Operations Plan and Addendum prepared by Saulnier (1988, 1991 ) under the technical direction of Sandia National Laboratories, Albuquerque, New Mexico.

Aging analyses were performed on solder joints from two radar units: (1) a laboratory, N57 tube-type radar unit and (2) a field-returned, B61-0, tube-type radar unit. The cumulative temperature environments experienced by the units during aging were calculated from the intermetallic compound layer thickness and the mean Pb-rich phase particle size metrics for solder joints in the units, assuming an aging time of 35 years for both radars. Baseline aging metrics were obtained from a laboratory test vehicle assembled at AS/FM and T; the aging kinetics of both metrics were calculated from isothermal aging experiments. The N57 radar unit interconnect board solder joints exhibited very little aging. The eyelet solder joints did show cracking that most likely occurred at the time of assembly. The eyelet, SA1126 connector solder joints, showed some delamination between the Cu pad and underlying laminate. The B61 field-returned radar solder joints showed a nominal degree of aging. Cracking of the eyelet solder joints was observed. The Pb-rich phase particle measurements indicated additional aging of the interconnects as a result of residual stresses. Cracking of the terminal pole connector, pin-to-pin solder joint was observed; but it was not believed to jeopardize the electrical functionality of the interconnect. Extending the stockpile lifetime of the B61 tube-type radar by an additional 20 years would not be impacted by the reliability of the solder joints with respect to further growth of the intermetallic compound layer. Additional coarsening of the Pb-rich phase will increase the joints' sensitivity to thermomechanical fatigue.

This report summarizes a public workshop that was held on April 27, 1999, in Rockville, Maryland. The workshop was conducted as part of the US Nuclear Regulatory Commission's (NRC) efforts to further develop its understanding of the risks associated with low power and shutdown operations at US nuclear power plants. A sufficient understanding of such risks is required to support decision-making for risk-informed regulation, in particular Regulatory Guide 1.174, and the development of a consensus standard. During the workshop the NRC staff discussed and requested feedback from the public (including representatives of the nuclear industry, state governments, consultants, private industry, and the media) on the risk associated with low-power and shutdown operations.

For a number of years, we have been initiating steam explosions of single drops of molten materials with pressure and flow (bubble growth) transients generated by discharging a capacitor bank through gold bridgewires placed underwater. Recent experimental and theoretical advances in the field of steam explosions, however, have made it important to substantially increase these relatively mild transients in water without using high explosives, if possible. To do this with the same capacitor bank, we have discharged similar energies through tiny strips of aluminum foil submerged in water. By replacing the gold wires with the aluminum strips, we were able to add the energy of the aluminum-water combustion to that normally deposited electrically by the bridgewire explosion in water. The chemical enhancement of the explosive characteristics of the discharges was substantial: when the same electrical energies were discharged through the aluminum strips, peak pressures increased as much as 12-fold and maximum bubble volumes as much as 5-fold above those generated with the gold wires. For given weights of aluminum, the magnitudes of both parameters appeared to exceed those produced by the underwater explosion of equivalent weights of high explosives.

A 2-D, lattice-Monte Carlo approach was developed to simulate ferroelectric domain structure. The model currently utilizes a Hamiltonian for the total energy based only upon electrostatic terms involving dipole-dipole interactions, local polarization gradients and the influence of applied electric fields. The impact of boundary conditions on the domain configurations obtained was also examined. In general, the model exhibits domain structure characteristics consistent with those observed in a tetragonally distorted ferroelectric. The model was also extended to enable the simulation of ferroelectric hysteresis behavior. Simulated hysteresis loops were found to be very similar in appearance to those observed experimentally in actual materials. This qualitative agreement between the simulated hysteresis loop characteristics and real ferroelectric behavior was also confirmed in simulations run over a range of simulation temperatures and applied field frequencies.

Real-time measurements of island coarsening during SiGe/Si (001) deposition reveal unusual kinetics. In particular, the mean island volume increases superlinearly with time, while the areal density of islands decreases at a faster-than-linear rate. Neither observation is consistent with standard considerations of Ostvvald ripening. We attribute our observed kinetics to the effect of elastic interactions in the densely growing island array. Island coalescence likely plays an important role as well.

The effect of Inductively Coupled Plasma H{sub 2} or Ar discharges on the breakdown voltage of p-GaN diodes was measured over a range of ion energies and fluxes. The main effect of plasma exposure is a decrease in net acceptor concentration to depths of 400-550{angstrom}. At high ion fluxes or energies there can be type conversion of the initially p-GaN surface. Post etch annealing at 900 C restores the initial conductivity.

The field of microfluidics is undergoing rapid growth in terms of new device and system development. Among the many methods of fabricating microfluidic devices and systems, surface micromachining is relatively underrepresented due to difficulties in the introduction of fluids into the very small channels produced, packaging problems, and difficulties in device and system characterization. The potential advantages of using surface micromachining including compatibility with the existing integrated circuit tool set, integration of electronic sensing and actuation with microfluidics, and fluid volume minimization. In order to explore these potential advantages we have developed first generation surface micromachined microfluidic devices (channels) using an adapted pressure sensor fabrication process to produce silicon nitride channels, and the SUMMiT process to produce polysilicon channels. The channels were characterized by leak testing and flow rate vs. pressure measurements. The fabrication processes used and results of these tests are reported in this paper.

Very high current generators are being developed to drive compact loads leading to conductors carrying very high current densities. Losses in conductors include resistive, magnetic field diffusion, pdV work, and material motion contributions. We have designed and executed experiments on Sandia's 100-ns rise time, 20- MA Z accelerator to quantify those losses at current densities reaching 10 MA/cm. In these experiments we delivered nearly 20 MA to both high-current density and low-current density short circuit loads. We used B-dot probes and VISAR techniques to measure the magnetic field near the load. A reduction in the delivered current of ~ 15% over the 20-MA peak current prediction made without resistive losses was observed. Comparisons of these data with radiation magneto-hydrodynamics codes (RMHD) will be presented. Implications on the efficiency of next generation pulsed power drivers will be discussed.

We have demonstrated successful operation of a 3.35- m-diameter insulator stack at 158 kV/cm on five consecutive Z-accelerator shots. The stack consisted of five +45°-profile 5.715-cm-thick cross-linked-polystyrene (Rexolite- 1422) insulator rings, and four anodized- aluminum grading rings shaped to reduce the field at cathode triple junctions. The width of the voltage pulse at 89% of peak was 32 ns. We compare this result to a new empirical flashover relation developed from previous small-insulator experiments conducted with flat unanodized electrodes. The relation predicts a 50% flashover probability for a Rexolite insulator during an applied voltage pulse when E_maxe^-0.27/d(t_effC)^1/10 = 224, where E_max is the peak mean electric field (kV/cm), d is the insulator thickness (cm), t_eff is the effective pulse width (ps), and C is the insulator circumference (cm). We find the Z stack can be operated at a stress at least 19% higher than predicted. This result, and previous experiments conducted by Vogtlin, suggest anodized electrodes with geometries that reduce the field at both anode and cathode triple junctions would improve the flashover strength of +45° insulators.

In August of 1998 the Z facility leaked approximately 150 gallons of deionized water into the dielectric oil of the Energy Storage Section (ESS). After processing the oil to remove existing particulate and free water the dielectric breakdown strength increased from the mid 20kV range to values in excess of 40 kV. 40 kV is above historical operating levels of about 35 kV. This, however, was not enough to allow 90 kV charging of the Marx Generators in the ESS. Further analysis of the oil showed dissolved water at a saturated level (70 - 80 ppm) and some residual particulate contamination smaller than 3 microns. The dissolved water and particulate combination was preventing the 90 kV charging of the Marx Generators in the ESS. After consulting with the oil industry it was determined that nitrogen sparging could be used to remove the dissolved water. Further particulate filtering was also conducted. After approximately 20 hours of sparging the water content in the ESS was reduced to 42 ppm which enabled Marx charging to 90 kV.

Fischer-Tropsch synthesis was discovered in Germany in the 1920's and has been studied by every generation since that time. As technology and chemistry, in general, improved through the decades, new insights, catalysts, and technologies were added to the Fischer-Tropsch process, improving it and making it more economical with each advancement. Opportunities for improving the Fischer-Tropsch process and making it more economical still exist. This paper gives an overview of the present Fischer-Tropsch processes and offers suggestions for areas where a research investment could improve those processes. Gas-to-liquid technology, which utilizes the Fischer Tropsch process, consists of three principal steps: Production of synthesis gas (hydrogen and carbon monoxide) from natural gas, the production of liquid fuels from syngas using a Fischer-Tropsch process, and upgrading of Fischer-Tropsch fuels. Each step will be studied for opportunities for improvement and areas that are not likely to reap significant benefits without significant investment.

Spatially Interpolated Nonlinear Anodization in Synthetic Aperture Original formulation of spatially variant anodization for complex synthetic aperture radar (SAR) imagery oversampled at twice the Nyquist rate (2.OX). Here we report a spatially interpolating, noninteger-oversampled SVA sidelobe. The pixel's apparent IPR location is assessed by comparing its value to the sum of its value plus weighted comparable for exact interpolation. However, exact interpolation implies an ideal sine interpolator3 and large components may not be necessary. Note that P is the summation of IPR diagonal values. The value of a sine IPR on the diagonals is a sine-squared; values much less than cardinal direction (m, n) values. This implies that cardinal direction interpolation requires higher precision than diagonal interpolation. Consequently, we employed a smaller set. The spatially interpolated SVA used an 8-point/4-point sine interpolator described above. Table 1 shows the Table 1 results show a two-times speed-up using the 1.3x oversampled and spatially interpolated SVA over the Figure 1d. Detected results of 1.3x oversampled sine interpolated spatially variant

Floating body effects can undermine the soft-error tolerance of partially-depleted SOI technologies [1, 2]. Body ties are used to mitigate floating body effects [3,4]. In this paper, we study the charge collection properties and effectiveness of different body tie designs for reducing soft errors induced by energetic particle strikes.

It is well established that pulsed power technology is relatively cheaper than other architectures aiming to produce high-current, high-voltage electron or ion accelerators. The footprints of most pulsed power accelerators are large making them incompatible for applications that require either portability or a large number of similar components for very high power devices (like Z-pinch accelerators). Most of the modern pulsed power accelerators require several stages of pulse conditioning (pulse forming) to convert the multimicrosecond pulse of a Marx generator output to the 50-1 00-ns pulse required for an electron or ion diode or a cell cavity of an inductive voltage adder We propose a new and unique method for constmcting high-current, high-voltage pulsed accelerators. The salient future of the approach is switching and inductively adding the pulses at low voltage straight out of the capacitors through low inductance transfer and soft iron core isolation. High currents can be achieved by feeding each core with many capacitors connected in parallel in a circular array. High voltage is obtained by inductively adding many stages in series. Utilizing the presently available capacitors and switches we can build a 300-kA, 7-MV generator with an overall outer diameter (including capacitors and switches) of 1.2 m and length of 6.5 m! In addition our accelerator can be multipulsed with a repetition rate up to the capacitor specifications and no less than 10 Hz. As an example the design of a 3-MeV, 100-kA accelerator is presented and analyzed.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This set of view graphs outline the simulation of the behavior of polyelectrolytes.

We are conducting a comprehensive experimental study of the electromechanical behavior of poled PZT 95/5 (lead zirconate titattate). As part of this study, eight plane-wave tests have been conducted on axially poled PZT 95/5 at stress levels ranging from 0.9 to 4.6 GPa, using VISAR and electrical diagnos- tics. Observed wave velocities were slightly decreased from ultrasonic vahtes, by contrast' with unpoled samples. Compression waveforms show a step at 0.6 GPa more marked than for normally poled or unpoled samples; this may correspond to a poling effect on the ferroelectric/antiferroelectric transition. A similar step is observed on release. The released charge upon loading to 0.9 GPa is consistent with nearly complete depoling. Loading to higher stresses gave lower currents (factor of 10), suggesting shock-induced conduc- tivity or electrical breakdown.

A new mold material has been developed for use in making rare-earth permanent magnet components with precise dimensions in the 10 to 1000 µm range by hot-forging. These molds are made from molds poly(methyl)methacrylate (PMMA) made by deep x-ray lithography (DXRL). An alumina bonded with colloidal silica has been developed for use in these molds. This material can be heated to 950°C without changing dimensions where it develops the strength needed to withstand the hot-fmging conditions (750°C, 100 MPa). In addition, it disintegrates in HF so that parts can be easily removed after forging.

Magnetic field-structured-composites (FSCs) are made by structuring magnetic particle suspensions in uniaxial or biaxial (e.g. rotating) magnetic fields, while polymerizing the suspending resin. A uniaxial field produces chain-like particle structures, and a biaxial field produces sheet-like particle structures. In either case, these anisotropic structures affect the measured magnetic hysteresis loops, with the magnetic remanence and susceptibility increased significantly along the axis of the structuring field, and decreased slightly orthogonal to the structuring field, relative to the unstructured particle composite. The coercivity is essentially unaffected by structuring. We present data for FSCs of magnetically soft particles, and demonstrate that the altered magnetism can be accounted for by considering the large local fields that occur in FSCs. FSCS of magnetically hard particles show unexpectedly large anisotropies in the remanence, and this is due to the local field effects in combination with the large crystalline anisotropy of this material.

Composites of carbon black particles in polyethylene are known to exhibit an unusually rapid increase in resistivity as the applied field is increased, making this material useful in automatically resettable fuses. In this application the composite is in series with the circuit it is protecting: at low applied voltages this circuit is the load, but at high applied voltages the composite becomes the load, limiting the current to the circuit. We present a simple model of this behavior in terms of a network of nonlinear conductors. Each conductor has a conductance that depends on its instantaneous Joule heating. It is shown that in the fusing regime, where the current through the composite decreases with increasing voltage, an plate-like dissipation instability develops normal to the applied field. Experimental evidence of this phenomena is described.

Abstract not provided.

Abstract not provided.

Iron catalysts are particularly useful for Fischer-Tropsch (FT) synthesis when the H2 to CO ratio of the synthesis gas is low since iron exhibits water gas shift as well as FT activity. Iron catalysts are active for Fischer Tropsch synthesis only when in the carbide state. The active iron carbide catalyst has a 1-3 nm carbonaceous layer, which can only be found on the carbided iron catalyst (no carbonaceous material is found on iron oxide particles that maybe present). This paper will address the nature of the carbonaceous material that is required for product formation. The carbonaceous material is amorphous, does not require hydrogen to form, and is the starting material for FT products.

Hydrogen was regarded as a harmful impurity in many alloys and particularly in steels where it gives rise to a specific type of embrittlement and forms various discontinuities like flakes and blowholes. For this reason, the researcher efforts were mainly focused on eliminating hydrogen's negative impacts and explaining its uncommonly high diffusivity in condensed phases. Meanwhile, positive characteristics of hydrogen as an alloying element remained unknown for quite a long time. Initial reports in this field did not appear before the early 1970s. Data on new phase diagrams are given for metal-hydrogen systems where the metal may or may not form hydrides. Various kinds of hydrogen impact on structure formation in solidification, melting and solid-solid transformations are covered. Special attention is given to the most popular alloys based on iron, aluminum, copper, nickel, magnesium and titanium. Detailed is what is called gas-eutectic reaction resulting in a special type of gas-solid structure named gasarite. Properties and applications of gasars - gasaritic porous materials - are dealt with. Various versions of solid-state alloying with hydrogen are discussed that change physical properties and fabrication characteristics of metals. Details are given on a unique phenomenon of anomalous spontaneous deformation due to combination of hydrogen environment and polymorphic transformation. All currently known versions of alloying with hydrogen are categorized for both hydride-forming and non-hydrid forming metals.

Particles are inevitably generated in physical vapor deposition (PVD) systems due to the delamination of deposited films on various process chamber parts and shielding. Non-collimated (blanket) and collimated PVD Titanium Nitride (TiN) deposition processes are used for metal ARC (anti-reflective coating) and underlayers, and for the "contact liner" deposition steps (TiN adhesion layers before plug formation). Probe yield analysis and SRAM bit failure analysis, using conventional failure analysis, have shown that particles at these process steps can have a significant impact on wafer yields. In many typical semiconductor wafer fabs, particles generated by TiN film deposition rank consistently at or near the top of the defect pareto. This paper summarizes the results of defect reduction experiments conducted on an Applied Materials Endura Physical Vapor Deposition (PVD) system and various off-line experiments examining film and adhesion characteristics. It includes the results of film adhesion and shield temperature control experiments aimed at reducing defect levels. Key fidings, particle reduction results, and recommended defect reduction measures are presented. The reduction in particles not only can improve yields, but also result in substantial cost savings through the extension of chamber kit end-of-life (EOL).

The pressure-induced phase transition in CdS was investigated using picosecond time-resolved electronic spectroscopy in plate impact shock wave experiments. Real-time changes in the electronic spectra were observed, with 100 ps time resolution, in single crystals of CdS shocked along the c and a axes to peak stresses between 35 and 90 kbar (above the phase transition stress of approximately 30 kbar measured in continuum studies). When shocked to stresses above approximately 50 kbar along the crystal c axis and 60 to 70 kbar along the crystal a axis, the crystals undergo a very rapid change in electronic structure, indicating that significant structural changes occur within the first 100 ps. These results, along with previous ns continuum measurements, make a strong case for a metastable state during the phase transition in shocked CdS. Ab-initio periodic Hartree-Fock calculations (with DFT correlation corrections) were employed to examine the compression of CdS and to determine a possible lattice structure for the proposed metastable structure. These results, along with details of the transformation kinetics and orientational dependence, will be discussed. Work supported by ONR.

In previous studies, ruby R-line shifts under shock compression and tension have been measured using the spontaneous luminescence from optically pumped samples. Signal intensities obtained through the use of this method are limited by the short time duration of the experiments (100 ns to several ps) in comparison to the long lifetime of the luminescence (approximately 3 ins). We have investigated the use of stimulated emission as a technique for measuring R-line shifts in shocked ruby crystals. Feasibility experiments were performed both at ambient conditions and under shock compression to 60 kbar using an experimental configuration similar to that used for time resolved ruby luminescence measurements in previous shock wave studies. Signal gain due to stimulated emission was observed, with gains ranging from 1.1 to 3.4, in agreement with calculations performed for the particular experimental configuration used. The present results make a good case for incorporating this technique to measure shock induced R-line shifts in ruby. Work supported by DSWA.

A series of two-dimensional hydrodynamic calculations using the two-dimensional Second- order Hydrodynamic Automated Mesh Refinement Code (SHAMRC) developed by Applied Research Associates, Inc. (ARA), was made with the objective of understanding the behavior of aqueous foams in the presence of a C4-generated blast wave. A full three-phase water equation-of-state was incorporated in the first calculation. Comparison of the results of the first calculation with experimental data collected by Sandia National Laboratories (SNL) indicated that the interaction was much more complicated than could be represented by a mixture of detonation products, air, and water in local temperature and pressure equilibrium. Other models were incorporated in the code to examine the effects of thermal non-equilibrium between water and the gases and allowed for two-phase flow. The water droplets were allowed to slip relative to the gas velocity, providing non-equilibrium for the velocity distribution. These models permitted heated liquid droplets to be accelerated at high pressures and transported through and ahead of the decaying shock front. The droplets then exchanged momentum and energy with the foam ahead of the shock and preconditioned the medium through which the shock was propagating. This process had the effect of diffusing the shock front and its associated energy. These relatively high resolution calculations develop numerical representations of the Rayleigh-Taylor instabilities at the detonation products/foam interface. This unstable interface plays in important role in understanding the behavior of the interaction of the detonation products with the foam. Figure 4 clearly shows the developing instabilities at the interface and an inward facing shock at a radius of 25 cm. The results of the calculations using the various models can be edited to provide the total energy exchanged between materials, the fraction of water vaporized, and the extent of detonation products as a function of time.

This section reviews physical processes involved in the implantation of energetic hydrogen into plasma facing materials and its subsequent diffusion, release, or immobilization by trapping or precipitation within the material. These topics have also been discussed in previous reviews. The term hydrogen or H is used here generically to refer to protium, deuterium or tritium.

Multi-kilojoule repetitive pulsed power technology moved from a laboratory environment into its first commercial application in 1997 as a driver for ion beam surface treatment. Sandia's RHEPP II, a repetitive 2.5 kJ/pulse electron beam accelerator, has supported the development of radiation treatment processes for polymers and elastomers, food products, and high dose- rate effects testing for defense programs since early 1996. Dos Lineas, an all solid-state testbed, has demonstrated synchronization techniques for parallel magnetic modulator systems and is continuing the development of design standards for long lifetime magnetic switches and voltage adders at a shot rate capability that exceeds 5x10⁶ pulses per day. This paper will describe progress in multi-kilojoule class repetitive pulsed power technology development, limitations of magnetic switching technology for accelerator and modulator applications, and future research and development directions.

Experimental results are presented that provide design guidelines for high repetition rate, long-life pulsed power magnetic modulators. Fault mechanisms that occurred during a series of 32 million shots at 100 pps, with continuous runs of up to 5.7 million shots (~16 hours) on the Dos Lineas magnetic modulator are described. An effort to explain the fault mechanisms and how to avoid them is made. Factors that limit the long life performance of a variety of components including switches, cables and oil are encountered. The high reliability of the magnetic switch technology is demonstrated.

The laser glass for the National Ignition Facility (NIF) Main Amplifier system is pumped by a system of 192 pulsed power/flash lamp assemblies. Each of these 192 assemblies consists of a 1.6 MJ (nominal) capacitor bank working with a Pre-Ionization/Lamp Check (PILC) pulser to drive an array of 40 flash lamps. This paper describes the predicted performance of these Power Conditioning System (PCS) modules in concert with flashlamp assemblies in NIF. Each flashlamp assembly consists of 20 parallel sets of lamps in series pairs. The sensitivity of system performance to various design parameters of the PILC pulser and the main capacitor bank is described. Results of circuit models are compared to sub-scale flashlamp tests and to measurements taken in tests of a PCS module driving a flashlamp assembly in the First Article NIF Test Module facility at Sandia National Laboratories. Also included are predictions from a physics-based, semi-empirical amplifier gain code.

Long range substituent effects on the ²⁹Si NMR chemical shifts in a series of alkylene and arylene-bridged triethoxysilanes were observed over as many as 11 bonds. The hydrolysis reaction of an ethoxide caused the resonance of the silicon on the opposing end of the bridging unit to move downfield. The alkylene bridging units ranged from ethylene to octylene while the arylene bridging units included phenyl and biphenyl. Resonance assignments were confirmed by the absence of these shifts for the triethoxysilyl in l-triphenylsilyl-2-triethoxysilylethane. The magnitude of the downfield shift decreased as the length of the bridging unit between silicon atoms increased. Transmission of the substituent effect along a polyethylene chain was successfully modeled by a through-bond mechanism with an attenuation factor of 1.88 for each methylene unit.

The Laser Engineered Net Shaping (LENSm) process is a laser assisted, direct metal manufacturing process under development at Sandia National Laboratories. The process incorporates features from stereo lithography and laser surfacing, using CAD file cross-sections to control the forming process. Powder metal particles (less than 150 micrometers) are delivered in a gas stream into the focus of a NdYAG laser to form a molten pool. The part is then driven on an x/y stage to generate a three-dimensional part by layer wise, additive processing. In an effort to understand the thermal behavior of the LENS process, in-situ high-speed thermal imaging has been coupled with microstructural analysis and finite element modeling. Cooling of the melt is accomplished primarily by conduction of heat through the part and substrate, and depending on the substrate temperature and laser input energy, cooling rates can be varied from 10 sup2; to 10 sup3; K s^-l. This flexibility allows control of the microstructure and properties in the part. The experiments reported herein were conducted on 316 stainless steel, using two different particle size distributions with two different average particle sizes. Thermal images of the molten pool were analyzed to determine temperature gradients and cooling rates in the vicinity of the molten pool, and this information was correlated to the microstructure and properties of the part. Some preliminary finite element modeling of the LENS process is also presented.

A new semiconductor alloy system, InGaAsN, has been identified as a can- didate material for multi junction solar cells having efficiencies greater than 40%. The introduction of small amounts of nitrogen ( 2%) into the InGaAs alloy system greatly reduces the band gap energy, with reductions approaching 0.4 eV for 2% nitrogen content With the appropriate ratio of indium to nitrogen concentrations, InGaAsN can be lattice matched to GaAs.

The angle of ion incidence at the etched wafer location during RIBE and IBE using Cl₂, Ar and O₂ ion beams has been characterized using an ion energy and angle analyzer. Effects of beam current and accelerator grid bias on beam divergence and the spatial uniformity of the spread of incident angles are measured. It is observed that increased total beam current can lead to reduced current density at the sample stage due to enhanced beam divergence at high currents. Results are related to preferred etch system design for uniform high-aspect-ratio etching across semiconductor wafers.

In the world of computer-based data acquisition and control, the graphical interface program LabVIEW from National Instruments is so ubiquitous that in many ways it has almost become the laboratory standard. To date, there have been approximately fifteen books concerning LabVIEW, but Professor Essick's treatise takes on a completely different tack than all of the previous discussions. In the more standard treatments of the ways and wherefores of LabVIEW such as LabVIEW Graphical Programming: Practical Applications in Instrumentation and Control by Gary W. Johnson (McGraw Hill, NY 1997), the emphasis has been instructing the reader how to program LabVIEW to create a Virtual Instrument (VI) on the computer for interfacing to a particular instruments. LabVIEW is written in G a graphical programming language developed by National Instruments. In the past the emphasis has been on training the experimenter to learn G . Without going into details here, G incorporates the usual loops, arithmetic expressions, etc., found in many programming languages, but in an icon (graphical) environment. The net result being that LabVIEW contains all of the standard methods needed for interfacing to instruments, data acquisition, data analysis, graphics, and also methodology to incorporate programs written in other languages into LabVIEW. Historically, according to Professor Essick, he developed a series of experiments for an upper division laboratory course for computer-based instrumentation. His observation was that while many students had the necessary background in computer programming languages, there were students who had virtually no concept about writing a computer program let alone a computer- based interfacing program. Thus the beginnings of a concept for not only teaching computer- based instrumentation techniques, but aiso a method for the beginner to experience writing a com- puter program. Professor Essick saw LabVIEW as the perfect environment in which to teach computer-based research skills. With this goal in mind, he has succeeded admirably. Advanced LabVIEW Labs presents a series of chapters devoted to not only introducing the reader to LabVIEW, but also to the concepts necessary for writing a successful computer pro- gram. Each chapter is an assignment for the student and is suitable for a ten week course. The first topic introduces the while loop and waveform chart VI'S. After learning how to launch LabVIEW, the student then leans how to use LabVIEW functions such as sine and cosine. The beauty of thk and subsequent chapters, the student is introduced immediately to computer-based instruction by learning how to display the results in graph form on the screen. At each point along the way, the student is not only introduced to another LabVIEW operation, but also to such subjects as spread sheets for data storage, numerical integration, Fourier transformations', curve fitting algorithms, etc. The last few chapters conclude with the purpose of the learning module, and that is, com- puter-based instrumentation. Computer-based laboratory projects such as analog-to-digital con- version, digitizing oscilloscopes treated. Advanced Lab VIEW Labs finishes with a treatment on GPIB interfacing and finally, the student is asked to create an operating VI for temperature con- trol. This is an excellent text, not only as an treatise on LabVIEW but also as an introduction to computer programming logic. All programmers, who are struggling to not only learning how interface computers to instruments, but also trying understand top down programming and other programming language techniques, should add Advanced Lab-VIEW Labs to their computer library.

Our data suggest a correlation between near-interface strain in SiO{sub 2} and the ratio of fixed vs. mobile positive charge generated at the interface during forming gas annealing. A model based on first-principles quantum mechanical calculations supports this correlation.

This paper will focus on the methodology of using a 2D plasma Direct Simulation Monte Carlo technique to simulate the species transport in an inductively coupled, low pressure, chemically reacting plasma system. The pressure in these systems is typically less than 20 mtorr with plasma densities of approximately 10{sup 17} {number_sign}/m{sup 3} and an ionization level of only 0.1%. This low ionization level tightly couples the neutral, ion, and electron chemistries and interactions in a system where the flow is subsonic. We present our strategy and compare simulation results to experimental data for Cl{sub 2} in a Gaseous Electronics Conference (GEC) reference cell modified with an inductive coil.

Hohlraums (measuring 6-mm in diameter by 7-mm in height) have been heated by x-rays from a z-pinch. Over measured x-ray input powers P of 0.7 to 13 TW, the hohlraum radiation temperature T increases from {approximately}55 to {approximately}130 eV, and is in agreement with the Planckian relation P-T{sup 4}. The results suggest that indirect-drive ICF studies involving NIF relevant pulse shapes and <2-mm diameter capsules can he studied using this arrangement.

Technical guidance for performance assessment (PA) of low-level radioactive waste (LLRW) sites is currently dependent upon experimental retardation factors (K{sub D}'s) to predict radionuclide transport. Accurate predictions of waste transport or retardation will require mechanistic models of radionuclide sorption so as to be applicable to a wide range of soil/groundwater environments. To that end, we have investigated Cs{sup +}, Sr{sup +}, and Ba{sup 2+} sorption on several clay and Fe-oxide minerals. Relative metal binding strengths for montmorillonite clay decrease from Ba{sup 2+} to Sr{sup +}, which is similar to that sorption trend noticed for kaolinite. Molecular dynamics simulations for kaolinite suggest that Cs{sup +} is sorbed at aluminol (010) edge sites as an inner-sphere complex and weakly sorbed as an outer-sphere complex on (001) basal surfaces. Sorption is thought to occur on similar sites for smectite clays, however, the basal plane residual charge and its increased basal plane exposure should have a greater influence on metal sorption. On the other hand, phase transformation kinetics (e.g., ferrihydrite to goethite) is a very important control of metal sorption and resorption for Fe-oxides/hydroxides. These results provide a basis for understanding and predicting metal sorption on complex soil minerals.

Experiments at the Z machine generate over four hundred channels of waveform data on each accelerator shot. Most experiments require timing accuracy to better than one nanosecond between multiple distributed recording locations throughout the facility. Experimental diagnostics and high speed data recording equipment are typically located within a few meters of the 200 to 300 terawatt X- ray source produced during Z-pinch experiments. This paper will discuss techniques used to resolve the timing of the several hundred data channels acquired on each shot event and system features which allow viewing of waveforms within a few minutes after a shot. Methods for acquiring high bandwidth signals in a severe noise environment will also be discussed.

Abstract not provided.

A retarding potential energy analyzer having 750 nm diameter, self-aligned grid apertures and micron scale grid separation has been fabricated using polycrystalline silicon and silicon dioxide. High resolution in situ measurements of ion velocity distributions have been demonstrated in inductively coupled argon plasmas. Measurement results agree well with those from a macroscopic analyzer. Important differences are observed in the energies of plasma ions when measured with respect to chamber wall versus those measured with respect to the plasma floating potential. Preliminary measurements under rf bias conditions have also been made and results follow the expected trends.

Technology development efforts are under way to apply chemical sensors to discriminate inert ordnance and clutter from live munitions that remain a threat to reutilization of military ranges. However, the chemical signature is affected by multiple environmental phenomena that can enhance or reduce its presence and transport behavior, and can affect the distribution of the chemical signature in the environment. For example, the chemical can be present in the vapor, aqueous, and solid phases. The distribution of the chemical among these phases, including the spatial distribution, is key in designing appropriate detectors, e.g., gas, aqueous or solid phase sampling instruments. A fundamental understanding of the environmental conditions that affect the chemical signature is needed to describe the favorable and unfavorable conditions of a chemical detector based survey to minimize the consequences of a false negative. UXO source emission measurements are being made to estimate the chemical flux from a limited set of ordnance items. Phase partitioning analysis has been completed to show what the expected concentrations of chemical analytes would be fi-om total concentrations measured in the soil. The soil moisture content in the dry region has been shown to be critical in the attenuation of soil gas concentrations by increased sorption to soil particles. Numerical simulation tools have been adapted to include surface boundary conditions such as solar radiation, surface boundary layer (which is a function of wind speed), precipitation and evaporation, and plant cover/root density to allow transport modeling and evaluate long term processes. Results of this work will provide performance targets for sensor developers and support operational decisions regarding field deployments.

A two-dimensional model is developed to simulate discharge of a lithium/thionyl chloride primary battery. The model accounts for not only transport of species and charge, but also the electrode porosity variations and the electrolyte flow induced by the volume reduction caused by electrochemical reactions. Numerical simulations are performed using a finite volume method of computational fluid dynamics. The predicted discharge curves for various temperatures are compared to the experimental data with excellent agreement. Moreover, the simulation results. in conjunction with computer visualization and animation techniques, confirm that cell utilization in the temperature and current range of interest is limited by pore plugging or clogging of the front side of the cathode as a result of LiCl precipitation. The detailed two-dimensional flow simulation also shows that the electrolyte is replenished from the cell header predominantly through the separator into the front of the cathode during most parts of the discharge, especially for higher cell temperatures.

The International Energy Agency (IEA) is an energy forum for 24 industrialized countries and was established in 1974 as an autonomous body within the Organization for Economic Cooperation and Development (OECD). The IEA Photovoltaic Power Systems (PVPS) program implementing agreement was signed in 1993, and renewed for another five years in 1998. Twenty-two countries are collaborating under the auspices of the IEA in the PVPS to address common technical and informational barriers that often limit the rate at which photovoltaic technologies advance into the markets. Task V of the IEA PVPS is entitled "Grid Interconnection of Building-Integrated and Other Dispersed Photovoltaic Power Systems." The task sponsored a workshop in September 1997 on grid-interconnection of photovoltaic systems and is planning a second workshop to address impacts of more penetration of dispersed systems into the utility grid. This paper will summarize the accomplishments of Task V over the last five years and will detail the planned work for the next three years.

There now exist close to 20 years of history in the application of Probabilistic Risk Assessment (PRA) for the analysis of fire risk at nuclear power plants. The current methods are based on various assumptions regarding fire phenomena, the impact of fire on equipment and operator response, and the overall progression of a fire event from initiation through final resolution. Over this same time period, a number of significant fire incidents have occurred at nuclear power plants around the world. Insights gained from US experience have been used in US studies as the statistical basis for establishing fire initiation frequencies both as a function of the plant area and the initiating fire source.To a lesser extent, the fire experience has also been used to assess the general severity and duration of fires. However, aside from these statistical analyses, the incidents have rarely been scrutinized in detail to verify the underlying assumptions of fire PRAs. This paper discusses an effort, under which a set of fire incidents are being reviewed in order to gain insights directly relevant to the methods, data, and assumptions that form the basis for current fire PRAs. The paper focuses on the objectives of the effort, the specific fire events being reviews methodology, and anticipated follow-on activities.

The sensitivity of surface acoustic wave (SAW) sensors has been enhanced by increasing the active surface area of these devices. Electrodepositions of Ni, Pd, and Pt in a mass-transport-limited mode with trace foreign metals yield highly dendritic crystal structures of uniform macroscopic thickness. The concentration of metal ions, supporting electrolyte, agitation, and additives greatly impact the crystal morphology of the deposit. This methodology can be used simply and economically to provide high-area films in selective regions.

Abstract not provided.

This paper improves on some of the limitations of conventional safety assessment and decision analysis methods. It develops a top-down mathematical method for expressing imprecise individual metrics as possibilistic or fuzzy numbers and shows how they may be combined (aggregated) into an overall metric, also portraying the inherent uncertainty. Both positively contributing and negatively contributing factors are included. Metrics are weighted according to significance of the attribute and evaluated as to contribution toward the attribute. Aggregation is performed using exponential combination of the metrics, since the accumulating effect of such factors responds less and less to additional factors. This is termed soft mathematical aggregation. Dependence among the contributing factors is accounted for by incorporating subjective metrics on overlap of the factors and by correspondingly reducing the overall contribution of these combinations to the overall aggregation. Decisions corresponding to the meaningfulness of the results are facilitated in several ways. First, the results are compared to a soft threshold provided by a sigmoid function. Second, information is provided on input ''Importance'' and ''Sensitivity,'' in order to know where to place emphasis on controls that may be necessary. Third, trends in inputs and outputs are tracked in order to add important information to the decision process. The methodology has been implemented in software.

In the 1990s, significant experience has been gained with high-speed passenger rail technologies. On the one hand, high speed versions of conventional-configuration trains, such as the French TGV, have proven themselves in service; on the other hand, magnetic levitation (maglev) trains such as the German Transrapid, which some expected to supplant conventional trains in some high speed applications, have not yet proven themselves and face a problematic future. This is because of maglev's high capital cost, the magnetic drag which it introduces, and the high development risks associated with this complex technology. This paper examines a new form of high-speed train expected to be capable of speeds of 300 mph, the Maglift Monorail. The Maglift Monorail was developed by simplifying and improving two well-understood technologies--wheelsets and LIMs--and then integrating them. The solution is a vehicle with flangeless wheels mounted in two axes, powered by a high-efficiency and light-weight LIM, positioned to give magnetic lift (maglift), i.e., electromagnetic force in the vertical direction which reduces the vehicle weight on the suspension, and thereby reduces static and rolling drag. Maglift can be considered a form of maglev as it uses the same electromagnetic forces to lift and propel the vehicle. This solution is presented in a Spanish-designed monorail system which has a unique suspension designed to minimize friction while giving great stability and turning capability. This monorail vehicle is propelled by the Seraphim motor (Segmented Rail Phased Induction Motor) which virtually eliminates magnetic drag and provides significant maglift. The Maglift Monorail achieves lower operating costs and a greater overall reduction in drag than conventional noncontact maglev does, and it does so without incurring maglev's high capital costs or its technology development risks.

There are currently two proposed standards for agent communication languages, namely, KQML (Finin, Lobrou, and Mayfield 1994) and the FIPA ACL. Neither standard has yet achieved primacy, and neither has been evaluated extensively in an open environment such as the Internet. It seems prudent therefore to design a general-purpose agent communications facility for new agent architectures that is flexible yet provides an architecture that accepts many different specializations. In this paper we exhibit the salient features of an agent communications architecture based on distributed metaobjects. This architecture captures design commitments at a metaobject level, leaving the base-level design and implementation up to the agent developer. The scope of the metamodel is broad enough to accommodate many different communication protocols, interaction protocols, and knowledge sharing regimes through extensions to the metaobject framework. We conclude that with a powerful distributed object substrate that supports metaobject communications, a general framework can be developed that will effectively enable different approaches to agent communications in the same agent system. We have implemented a KQML-based communications protocol and have several special-purpose interaction protocols under development.

When one considers the possibility of clandestine production of nuclear materials, one must consider the nature of the state. A Nuclear Weapon State (NWS) already has production facilities, and even though these might be safeguarded, the NWS could more easily hide the activities than could a Non-Nuclear Weapon State (NNWS). In this paper, some of the properties of production facilities are discussed in relation to how this would relate to vulnerability to detection. The observable and methods of detection are discussed, as well as the possibility that significant help by another country could totally eliminate one or more of the steps needed for a complete production cycle.

We present the results of molecular dynamics simulations of very long model polymer chains analyzed by various experimentally relevant techniques. The segment motion of the chains is found to be in very good agreement with the reptation model. We also calculated the plateau modulus G⁰_N. The predictions of the entanglement length N_e from G⁰_N and from the mean square displacement of the chain segments disagree by a factor of about 2.2(2), indicating an error in the prefactor in the standard formula for G⁰_N. We show that recent neutron spin echo measurements were carried out for chain lengths which are too small to allow for a correct determination of N_e.

It became clear during the workshop that the applicability of commercial satellite imagery to the verification of future regional arms control agreements is limited at this time. Non-traditional security topics such as environmental protection, natural resource management, and the development of infrastructure offer the more promising applications for commercial satellite imagery in the short-term. Many problems and opportunities in these topics are regional, or at least multilateral, in nature. A further advantage is that, unlike arms control and nonproliferation applications, cooperative use of imagery in these topics can be done independently of the formal Middle East Peace Process. The value of commercial satellite imagery to regional arms control and nonproliferation, however, will increase during the next three years as new, more capable satellite systems are launched. Aerial imagery, such as that used in the Open Skies Treaty, can also make significant contributions to both traditional and non-traditional security applications but has the disadvantage of requiring access to national airspace and potentially higher cost. There was general consensus that commercial satellite imagery is under-utilized in the Middle East and resources for remote sensing, both human and institutional, are limited. This relative scarcity, however, provides a natural motivation for collaboration in non-traditional security topics. Collaborations between scientists, businesses, universities, and non-governmental organizations can work at the grass-roots level and yield contributions to confidence building as well as scientific and economic results. Joint analysis projects would benefit the region as well as establish precedents for cooperation.

Preliminary experimental and modeling study of injection and transport of high current electron beams in current-neutralized background gas has been performed. Initial analysis of the results indicates that high current triaxial ring diode operates very reproducibly in the pinch mode. High current density beam can be injected efficiently into the drift region, using azimuthal guide field with reduced intensity near the injection region. This was shown to improve the effectiveness of capturing the beam for the transport. The transport length was insufficient to measure losses, such as would arise from scattering with the background gas.

Emerging technologies in the field of "Test & Measurement" have recently enabled the development of the Rapidly Adaptable Instrumentation Tester (RAIT). Based on software developed with LabVIEW®, the RAIT design enables quick reconfiguration to test and calibrate a wide variety of telemetry systems. The consequences of inadequate testing could be devastating if a telemetry system were to fail during an expensive flight mission. Supporting both open-bench testing as well as automated test sequences, the RAIT has significantly lowered total time required to test and calibrate a system. This has resulted in an overall lower per unit testing cost than has been achievable in the past.

Chemical detection of gaseous species at very low vapor pressures is possible for materials with very low, saturation vapor pressures. A saturation vapor pressure implies equilibrium with the solid or liquid phase of the material. Thus partitioning of the gaseous species into a phase such as a polymer, will result in a very large concentration of the species in the solid phase and greatly enhanced ability to detect this species. The concentration in the polymer of the species to be detected is limited by the volubility of the species in that phase. In this presentation we discuss such a situation were 2-nitro-diphenylamine (2NDPA) is detected in the gas phase at room temperature at the few parts per trillion level.

A new equivalent-circuit model for the thickness shear mode resonator with a surface viscoelastic layer will be described. This model is valid only in the vicinity of a film resonance but is a reasonable approximation away from resonance. A simple resonant parallel circuit containing a resistor, a capacitor, and an inductor represents the electrical impedance of the film. These elements describe the film's viscous power dissipation, elastic energy storage, and kinetic energy storage, respectively. Resonator response comparisons between this lumped- element model and the general transmission-line model show good agreement over a range of film phase conditions and not just near film resonance. Under certain conditions, it will be shown that two peaks in the admittance magnitude are observed for operation at film resonance.

The sensitivity of surface acoustic wave (SAW) sensors has been enhanced by increasing the active surface area of these devices, Electrodepositions of Ni, Pd, and Pt in a mass-transport-limited mode with trace foreign metals yield highly dendritic crystal structures of uniform macroscopic thickness. The concentration of metal ions, supporting electrolyte, agitation, and additives greatly impact the crystal morphology of the deposit. This methodology can be used simply and economically to provide high-area films in selective regions.

We report experimental results suggesting that mobile protons are generated at strained Si-O-Si bonds near the Si/SiO₂ interface during annealing in forming gas. Our data further suggest that the presence of the top Si layer plays a crucial role in the mobile H⁺ generation process. Finally, we show that the diffusion of the reactive species (presumably H₂ or H⁰) towards the H⁺ generation sites occurs laterally along the buried oxide layer, and can be impeded significantly due to the presence of trapping sites in the buried oxide.

The balance-of-system (BOS) of a photovoltaic installation includes the array structure, trackers, ac and dc wiring, overcur-rent protection, disconnects, interconnects, inverters, charge controllers, energy storage and system controllers. The inverter (sometimes called power-conditioning subsystem (PCS), power conditioner or static power converter) is the key electrical power-handling component of a photovoltaic (PV) power system that has, ac loads. This paper will focus on the inverter and its related functions as the critical electrical BOS element in photovoltaic systems. An evolutionary summary for inverter hardware development, primarily in the US, will shed light on the paths that have been taken to arrive at today's state-of-the-technology. Recent developments, integrated packaging and opportunities for practical technology and hardware advancements will be presented. This paper will also touch on elementary battery issues as they relate to inverters and their control functions. Batteries are also critical, but often misunderstood, BOS components in stand- alone systems.

During the Cold War the handling of Soviet military nuclear wastes was a classified topic--kept secret to hide the status and readiness of Soviet military forces. Following the end of the Cold War information about the handling of nuclear wastes by agencies of the Former Soviet Union (FSU) became available. The US Government response to the disclosure of disposal of radioactive wastes into the Arctic Ocean and into rivers that drain into the Arctic Ocean was the finding of the Arctic Nuclear Waste Assessment Program (ANWAP) in the Office of Naval Research (ONR). Projects were aided by ANWAP to study the behavior, transport, and fate of radionuclides in the Arctic Ocean. One of the research teams, the Risk Assessment Integration Group (RAIG) assessed the potential risks to humans and to the environment, particularly in the US Alaskan Arctic.