Additive manufacturing via selective laser melting can result in variable levels of internal porosity both between build plates and within components from the same build. In this investigation, sample porosity levels were compared to tensile properties for 176 samples spanning eight different build plates. Sample porosity was measured both by Archimedes density, which provided an estimation of overall porosity, and by observation of voids in the fracture surface, which provided an estimation of the porosity at the failure plane. The porosity observed at the fracture surface consistently demonstrated higher porosity than that suggested by Archimedes density. The porosity values obtained from both methods were compared against the mechanical results. Sample porosity appears to have some correlation to the ultimate tensile strength, yield strength, and modulus, but the strongest relationship is observed between porosity and ductility. Three different models were used to relate the fracture surface porosity to the ductility. The first method was a simple linear regression analysis, while the other two models have been used to relate porosity to ductility in cast alloys. It is shown that all three models fit the data well over the observed porosity ranges, suggesting that the models taken from casting theory can extend to additively manufactured metals. Finally, it is proposed that the non-destructive Archimedes method could be used to estimate an approximate sample ductility through the use of correlations realized here. Such a relationship could prove useful for design and for a deeper understanding of the impact of pores on tensile behavior.
Additive Manufacturing (AM) presents unprecedented opportunities to enable design freedom in parts that are unachievable via conventional manufacturing. However, AM-processed components generally lack the necessary performance metrics for widespread commercial adoption. We present a novel AM processing and design approach using removable heat sink artifacts to tailor the mechanical properties of traditionally low strength and low ductility alloys. The design approach is demonstrated with the Fe-50 at.% Co alloy, as a model material of interest for electromagnetic applications. AM-processed components exhibited unprecedented performance, with a 300 % increase in strength and an order-of-magnitude improvement in ductility relative to conventional wrought material. These results are discussed in the context of product performance, production yield, and manufacturing implications toward enabling the design and processing of high-performance, next-generation components, and alloys.
Soft ferromagnetic alloys are often utilized in electromagnetic applications due to their desirable magnetic properties. In support of these applications, the ferromagnetic alloys are also required to bear mechanical load under various loading and environmental conditions. In this study, a Fe–49Co–2V alloy was dynamically characterized in tension with a Kolsky tension bar and a Drop–Hopkinson bar at various strain rates and temperatures. Dynamic tensile stress–strain curves of the Fe–49Co–2V alloy were obtained at strain rates ranging from 40 to 230 s−1 and temperatures from − 100 to 100 °C. All dynamic tensile stress–strain curves exhibited an initial linear elastic response to an upper yield followed by Lüders band response and then a nearly linear work-hardening behavior. The yield strength of this material was found to be sensitive to both strain rate and temperature, whereas the hardening rate was independent of strain rate or temperature. The Fe–49Co–2V alloy exhibited a feature of brittle fracture in tension under dynamic loading with no necking being observed.
Equal channel angular extrusion (ECAE) of 49Fe-49Co-2V, also known as Hiperco® 50A or Permendur-2V, greatly improves the strength and ductility of this alloy, while sacrificing soft magnetic performance. In this work, ECAE Hiperco specimens were subjected to post-ECAE annealing in order to improve soft magnetic properties. The microstructure, mechanical properties, and magnetic performance are summarized in this study. Annealing begins above 650°C and a steep decline in yield strength is observed for heat treatments between 700 and 840°C due to grain growth and the Hall-Petch effect, although some strength benefit is still observed in fully annealed ECAE material compared to conventionally processed bar. Soft magnetic properties were assessed through B-H hysteresis curves from which coercivity (Hc) values were extracted. Hc decreases rapidly with annealing above 650°C as well, i.e. improved soft magnetic behavior. The observed trend is attributed to annealing and grain growth in this temperature regime, which facilitates magnetic domain wall movement. The coercivity vs. grain size results generally follow the trend predicted in the literature. The magnetic behavior of annealed ECAE material compares favorably to conventional bar, possibly due to mild crystallographic texturing which enhances properties in the post-ECAE annealed material. Overall, this study highlights a definitive tradeoff between mechanical and magnetic properties brought about by post-ECAE annealing and grain growth.
Fe-Co-2V is a soft ferromagnetic alloy used in electromagnetic applications due to excellent magnetic properties. However, the discontinuous yielding (Luders bands), grain-size-dependent properties (Hall-Petch behavior), and the degree of order/disorder in the Fe-Co-2V alloy makes it difficult to predict the mechanical performance, particularly in abnormal environments such as elevated strain rates and high/low temperatures. Thus, experimental characterization of the high strain rate properties of the Fe-Co-2V alloy is desired, which are used for material model development in numerical simulations. In this study, the high rate tensile response of Fe-Co-2V is investigated with a pulse-shaped Kolsky tension bar over a wide range of strain rates and temperatures. Effects of temperature and strain rate on yield stress, ultimate stress, and ductility are discussed.
Residual stress is a common result of manufacturing processes, but it is one that is often overlooked in design and qualification activities. There are many reasons for this oversight, such as lack of observable indicators and difficulty in measurement. Traditional relaxation-based measurement methods use some type of material removal to cause surface displacements, which can then be used to solve for the residual stresses relieved by the removal. While widely used, these methods may offer only individual stress components or may be limited by part or cut geometry requirements. Diffraction-based methods, such as X-ray or neutron, offer non-destructive results but require access to a radiation source. With the goal of producing a more flexible solution, this LDRD developed a generalized residual stress inversion technique that can recover residual stresses released by all traction components on a cut surface, with much greater freedom in part geometry and cut location. The developed method has been successfully demonstrated on both synthetic and experimental data. The project also investigated dislocation density quantification using nonlinear ultrasound, residual stress measurement using Electronic Speckle Pattern Interferometry Hole Drilling, and validation of residual stress predictions in Additive Manufacturing process models.
Intermetallic alloys possess exceptional soft magnetic properties, including high permeability, low coercivity, and high saturation induction, but exhibit poor mechanical properties that make them impractical to bulk process and use at ideal compositions. We used laser-based Additive Manufacturing to process traditionally brittle Fe–Co and Fe–Si alloys in bulk form without macroscopic defects and at near-ideal compositions for electromagnetic applications. The binary Fe–50Co, as a model material, demonstrated simultaneous high strength (600–700 MPa) and high ductility (35%) in tension, corresponding to a ∼300% increase in strength and an order-of-magnitude improvement in ductility relative to conventionally processed material. Atomic-scale toughening and strengthening mechanisms, based on engineered multiscale microstructures, are proposed to explain the unusual combination of mechanical properties. This work presents an instance in which metal Additive Manufacturing processes are enabling, rather than limiting, the development of higher-performance alloys.
Cylindrical dog-bone (or dumbbell) shaped samples have become a common design for dynamic tensile tests of ductile materials with a Kolsky tension bar. When a direct measurement of displacement between the bar ends is used to calculate the specimen strain, the actual strain in the specimen gage section is overestimated due to strain in the specimen shoulder and needs to be corrected. The currently available correction method works well for elastic-perfectly plastic materials but may not be applicable to materials that exhibit significant work-hardening behavior. In this study, we developed a new specimen strain correction method for materials possessing an elastic-plastic with linear work-hardening stress–strain response. A Kolsky tension bar test of a Fe-49Co-2V alloy (known by trade names Hiperco and Permendur) was used to demonstrate the new specimen strain correction method. This new correction method was also used to correct specimen strains in Kolsky tension bar experiments on two other materials: 4140 alloy, and 304L-VAR stainless steel, which had different work-hardening behavior.
Control of the atomic structure, as measured by the extent of the embrittling B2 chemically ordered phase, is demonstrated in intermetallic alloys through additive manufacturing (AM) and characterized using high fidelity neutron diffraction. As a layer-by-layer rapid solidification process, AM was employed to suppress the extent of chemically ordered B2 phases in a soft ferromagnetic Fe-Co alloy, as a model material system of interest to electromagnetic applications. The extent of atomic ordering was found to be insensitive to the spatial location within specimens and suggests that the thermal conditions within only a few AM layers were most influential in controlling the microstructure, in agreement with the predictions from a thermal model for welding. Analysis of process parameter effects on ordering found that suppression of B2 phase was the result of an increased average cooling rate during processing. AM processing parameters, namely interlayer interval time and build velocity, were used to systematically control the relative fraction of ordered B2 phase in specimens from 0.49 to 0.72. Hardness of AM specimens was more than 150% higher than conventionally processed bulk material. Implications for tailoring microstructures of intermetallic alloys are discussed.
This research applies nonlinear ultrasonic techniques for the quantitative characterization of additively manufactured materials. The characterization focuses on identifying the dislocation density produced during the additive constructive process in order to increase confidence on a part's performance and the success of the manufacturing process. Second harmonic generation techniques based on the transmission of Rayleigh surface waves are used to measure the ultrasonic nonlinearity parameter, β, which has proven a quantitative indicator of dislocations but has not been fully proven in additive manufactured materials. 316L and 304L stainless steel parts made from Powder Bed Fusion and Laser Engineered Net Shaping are compared between AM techniques and with wrought manufactured counterparts. β is consistently higher for additive manufactured parts. An annealing heat treatment is applied to each specimen to reduce dislocation density. β expectedly decreases by annealing in all specimens. A linear ultrasonic measurement is made to evaluate the effectiveness of using nonlinear techniques. The ultrasonic attenuation is higher for additive manufactured parts and increases at higher frequencies.
