Laser diode ignition experiments were conducted in an effort to characterize the effects of scale and heating rate on micro-scale explosive ignition criteria. Over forty experiments were conducted with various laser power densities and laser spot sizes. In addition, relatively simple analytical and numerical calculations were performed to assist with interpretation of the experimental data and characterization of the explosive ignition criteria.
A series of numerical simulations have been performed to determine scaling laws for fast ignition break even of a hot spot formed by energetic particles created by a short pulse laser. Hot spot break even is defined to be when the fusion yield is equal to the total energy deposited in the hot spot through both the initial compression and the subsequent heating. In these simulations, only a small portion of a previously compressed mass of deuterium-tritium fuel is heated on a short time scale, i.e., the hot spot is tamped by the cold dense fuel which surrounds it. The hot spot tamping reduces the minimum energy required to obtain break even as compared to the situation where the entire fuel mass is heated, as was assumed in a previous study [S. A. Slutz, R. A. Vesey, I. Shoemaker, T. A. Mehlhorn, and K. Cochrane, Phys. Plasmas 7, 3483 (2004)]. The minimum energy required to obtain hot spot break even is given approximately by the scaling law E{sub T} = 7.5({rho}/100){sup -1.87} kJ for tamped hot spots, as compared to the previously reported scaling of E{sub UT} = 15.3({rho}/100){sup -1.5} kJ for untamped hotspots. The size of the compressed fuel mass and the focusability of the particles generated by the short pulse laser determines which scaling law to use for an experiment designed to achieve hot spot break even.
This article provides a brief review of the field of electroporation and introduces a new microdevice that facilitates studies to test theories, gain understanding, and control this important biomedical technology. Electroporation, a bio-electrochemical process whose fundamentals are not yet understood, is a means of permeating the cell membrane by applying a voltage across the cell and forming nano-scale pores in the membrane. It has become an important field in biotechnology and medicine for the controlled introduction of macromolecules, such as gene constructs and drugs, into various cells. It is viewed as an engineering alternative to biological techniques for the genetic engineering of cells. To study and control electroporation, we have created a low-cost microelectroporation chip that incorporates a live biological cell with an electric circuit. The device revealed an important behavior of cells in electrical fields. They produce measurable electrical information about the electroporation state of the cell that may enable precise control of the process. The device can be used to facilitate fundamental studies of electroporation and can become useful in providing precise control over biotechnological processes.
This document provides a detailed discussion and a guide for the use of the RadCat 2.0 Graphical User Interface input file generator for the RADTRAN 5.5 code. The differences between RadCat 2.0 and RadCat 1.0 can be attributed to the differences between RADTRAN 5 and RADTRAN 5.5 as well as clarification for some of the input parameters. 3
The synthesis of a photoswitchable polymer by grafting an azobenzene dye to methacrylate followed by polymerization is presented. The azobenzene dye undergoes a trans-cis photoisomerization that causes a persistent change in the refractive index of cast polymer films. This novel polymer was incorporated into superlattices prepared by spin casting and the optical activity of the polymer was maintained. A modified coextruder that allows the rapid production of soft matter superlattices was designed and fabricated.
Two methods for creating a hybrid level-set (LS)/particle method for modeling surface evolution during feature-scale etching and deposition processes are developed and tested. The first method supplements the LS method by introducing Lagrangian marker points in regions of high curvature. Once both the particle set and the LS function are advanced in time, minimization of certain objective functions adjusts the LS function so that its zero contour is in closer alignment with the particle locations. It was found that the objective-minimization problem was unexpectedly difficult to solve, and even when a solution could be found, the acquisition of it proved more costly than simply expanding the basis set of the LS function. The second method explored is a novel explicit marker-particle method that we have named the grid point particle (GPP) approach. Although not a LS method, the GPP approach has strong procedural similarities to certain aspects of the LS approach. A key aspect of the method is a surface rediscretization procedure--applied at each time step and based on a global background mesh--that maintains a representation of the surface while naturally adding and subtracting surface discretization points as the surface evolves in time. This method was coded in 2-D, and tested on a variety of surface evolution problems by using it in the ChISELS computer code. Results shown for 2-D problems illustrate the effectiveness of the method and highlight some notable advantages in accuracy over the LS method. Generalizing the method to 3D is discussed but not implemented.
Understanding and characterizing the electrical properties of multi-conductor shielded and unshielded cables is an important endeavor for many diverse applications, including airlines, land based communications, nuclear weapons, and any piece of hardware containing multi-conductor cabling. Determining the per unit length capacitance and inductance based on the geometry of the conductors, number of conductors, and characteristics of the shield can prove quite difficult. Relating the inductance and capacitance to shielding effectiveness can be even more difficult. An exceedingly large number of measurements were taken to characterize eight multi-conductor cables, of which four were 3-conductor cables and four were 18-conductor cables. Each set of four cables contained a shielded cable and an unshielded cable with the inner conductors twisted together and a shielded cable and an unshielded cable with the inner conductors not twisted together (or straight). Male LJT connectors were attached on either end of the cable and each cable had a finished length of 22.5 inches. The measurements performed were self and mutual inductance, self and mutual capacitance, and effective height. For the 18 conductor case there ended up being an 18 by 18 element matrix for inductance (with the self inductance terms lying on the diagonal) and an 18 by 18 matrix for capacitance. The effective height of each cable was measured over a frequency range from 220 MHz to 18 GHz in a Mode-Stirred Chamber. The effective height of each conductor of each cable was measured individually and all shorted together, producing 19 frequency responses for each 18 conductor cable. Shielding effectiveness was calculated using the effective heights from the shielded and unshielded cables. The results of these measurements and the statistical analysis of the data will be presented. There will also be a brief presentation of comparison with numerical models.
This report describes an approach for extending the one-dimensional turbulence (ODT) model of Kerstein [6] to treat turbulent flow in three-dimensional (3D) domains. This model, here called ODTLES, can also be viewed as a new LES model. In ODTLES, 3D aspects of the flow are captured by embedding three, mutually orthogonal, one-dimensional ODT domain arrays within a coarser 3D mesh. The ODTLES model is obtained by developing a consistent approach for dynamically coupling the different ODT line sets to each other and to the large scale processes that are resolved on the 3D mesh. The model is implemented computationally and its performance is tested and evaluated by performing simulations of decaying isotropic turbulence, a standard turbulent flow benchmarking problem.
Military test and training ranges operate with live fire engagements to provide realism important to the maintenance of key tactical skills. Ordnance detonations during these operations typically produce minute residues of parent explosive chemical compounds. Occasional low order detonations also disperse solid phase energetic material onto the surface soil. These detonation remnants are implicated in chemical contamination impacts to groundwater on a limited set of ranges where environmental characterization projects have occurred. Key questions arise regarding how these residues and the environmental conditions (e.g., weather and geostratigraphy) contribute to groundwater pollution impacts. This report documents interim results of a mass transfer model evaluating mass transfer processes from solid phase energetics to soil pore water based on experimental work obtained earlier in this project. This mass transfer numerical model has been incorporated into the porous media simulation code T2TNT. Next year, the energetic material mass transfer model will be developed further using additional experimental data.
The presentation outline of this paper is: (1) How identification of chemical hazards fits into a security risk analysis approach; (2) Techniques for target identification; and (3) Identification of chemical hazards by different organizations. The summary is: (1) There are a number of different methodologies used within the chemical industry which identify chemical hazards: (a) Some develop a manual listing of potential targets based on published lists of hazardous chemicals or chemicals of concern, 'expert opinion' or known hazards. (b) Others develop a prioritized list based on chemicals found at a facility and consequence analysis (offsite release affecting population, theft of material, product tampering). (2) Identification of chemical hazards should include not only intrinsic properties of the chemicals but also potential reactive chemical hazards and potential use for activities off-site.
Technologies that could quickly detect and identify virus particles would play a critical role in fighting bioterrorism and help to contain the rapid spread of disease. Of special interest is the ability to detect the presence and movement of virions without chemically modifying them by attaching molecular probes. This would be useful for rapid detection of pathogens in food or water supplies without the use of expensive chemical reagents. Such detection requires new devices to quickly screen for the presence of tiny pathogens. To develop such a device, we fabricated nanochannels to transport virus particles through ultrashort laser cavities and measured the lasing output as a sensor for virions. To understand this transduction mechanism, we also investigated light scattering from virions, both to determine the magnitude of the scattered signal and to use it to investigate the motion of virions.
This overview is intended to provide the reader with insight into basic reliability issues often confronted when designing long-term geothermal well monitoring equipment. No single system is looked at. General examples of the long-term reliability of other industries are presented. Examples of reliability issues involving electronic components and sensors along with fiber optic sensors and cables are given. This paper will aid in building systems where a long operating life is required. However, as no introductory paper can cover all reliability issues, basic assembly practices and testing concepts are presented.
IFPACK provides a suite of object-oriented algebraic preconditioners for the solution of preconditioned iterative solvers. IFPACK constructors expect the (distributed) real sparse matrix to be an Epetra RowMatrix object. IFPACK can be used to define point and block relaxation preconditioners, various flavors of incomplete factorizations for symmetric and non-symmetric matrices, and one-level additive Schwarz preconditioners with variable overlap. Exact LU factorizations of the local submatrix can be accessed through the AMESOS packages. IFPACK , as part of the Trilinos Solver Project, interacts well with other Trilinos packages. In particular, IFPACK objects can be used as preconditioners for AZTECOO, and as smoothers for ML. IFPACK is mainly written in C++, but only a limited subset of C++ features is used, in order to enhance portability.
The evolution of Coulomb interactions across the metal insulator transition (MIT) in a 3D localized conductor was experimentally investigated. The data were used to construct a phase diagram of the macroscopic Coulomb-correlated states as a function of single-particle energy and density. The phase diagrams show the existence of a phase boundary that separates low-energy distinctive metallic or insulating behavior from a higher energy mixed state. The data indicate a diverging screening radius at the critical density, which may signal an interaction-driven thermodynamic state change.
This document transmits the U.S. Fish and Wildlife Service's (Service) biological and conference opinions based on our review of National Nuclear Security Administration's (NNSA) proposed Maximum Operations Alternative at Sandia National Laboratories (SNL/CA), Alameda County, California.
One effect noted during the March 1975 fire at the Browns Ferry plant is that fire-induced cable damage caused a range of unanticipated circuit faults including spurious reactor status signals and the apparent spurious operation of plant systems and components. Current USNRC regulations require that licensees conduct a post-fire safe shutdown analysis that includes consideration of such circuit effects. Post-fire circuit analysis continues to be an area of both technical challenge and regulatory focus. This paper discusses risk perspectives related to post-fire circuit analysis. An opening background discussion outlines the issues, concerns, and technical challenges. The paper then focuses on current risk insights and perspectives relevant to the circuit analysis problem. This includes a discussion of the available experimental data on cable failure modes and effects, a discussion of fire events that illustrate potential fire-induced circuit faults, and a discussion of risk analysis approaches currently being developed and implemented.
The complexity associated with the dynamics of wire arrays from individual wire ablation to wire-wire interaction and finally stagnation have been observed with relatively recent advances in experimental diagnostics. These experimental snapshots illustrate the existence of three-dimensional effects (e.g. wire precursor ablation and stagnation, array mass left behind, current density redistribution, multiple stagnations) that have a significant impact on the total radiation output. A detailed understanding of the magnitude and impact of these perturbations is lacking, especially those perturbations in three-dimensions. Sandia National Laboratories has developed a new multi-physics simulation framework tailored to high energy density physics (HEDP) environments. ALEGRA-HEDP[1] has begun to simulate this environment and has produced the highest fidelity, two-dimensional simulations of wire-array precursor ablation to date. The three-dimensional code capability now provides the ability to solve for the magnetic field and current density distribution associated with both the wire array and the complex current return structure. With this new capability the impact that experimental view-ports (e.g., slots in the current return can and radial spokes) have on the magnetic field surrounding the array can be investigated. Specifically, the impact that the perturbed magnetic field has on an idealized cylindrical liner implosion has been investigated.
The turbulent convection that takes place in a Chandrasekhar-mass white dwarf during the final few minutes before it explodes determines where and how frequently it ignites. Numerical simulations have shown that the properties of the subsequent Type la supernova are sensitive to these ignition conditions. A heuristic model of the turbulent convection is explored. The results suggest that supernova ignition is likely to occur at a radius of order 100 km, rather than at the center of the star.
Boyles, Katie A.; LeBeau, Gerald J.; Gallis, Michael A.
Three-dimensional Direct Simulation Monte Carlo simulations of Columbia Shuttle Orbiter flight STS-107 are presented. The aim of this work is to determine the aerodynamic and heating behavior of the Orbiter during aerobraking maneuvers and to provide piecewise integration of key scenario events to assess the plausibility of the candidate failure scenarios. The flight of the Orbiter is examined at two altitudes: 350-kft and 300-kft. The flowfield around the Orbiter and the heat transfer to it are calculated for the undamaged configuration. The flow inside the wing for an assumed damage to the leading edge in the form of a 10- inch hole is studied.
This report covers the basic design of the Sandia downhole geothermal reservoir monitoring system. The monitoring system can operate continuously at temperatures up to 240°C (464°F) while measuring small pressure and temperature changes in reservoirs. Future improvements in the existing system will come from research and development programs by such agencies as NASA, JPL, USAF and NETL. An explanation of the benefits of this research to the Geothermal HT electronics program will be given.
