The additive manufacture of compositionally graded Al/Cu parts by laser engineered net shaping (LENS) is demonstrated. The use of a blue light build laser enabled deposition on a Cu substrate. The thermal gradient and rapid solidification inherent to selective laser melting enabled mass transport of Cu up to 4 mm from a Cu substrate through a pure Al deposition, providing a means of producing gradients with finer step sizes than the printed layer thicknesses. Divorcing gradient continuity from layer or particle size makes LENS a potentially enabling technology for the manufacture of graded density impactors for ramp compression experiments. Printing graded structures with pure Al, however, was prevented by the growth of Al2Cu3 dendrites and acicular grains amid a matrix of Al2Cu. A combination of adding TiB2 grain refining powder and actively varying print layer composition suppressed the dendritic growth mode and produced an equiaxed microstructure in a compositionally graded part. Material phase was characterized for crystal structure and nanoindentation hardness to enable a discussion of phase evolution in the rapidly solidifying melt pool of a LENS print.
Directed energy deposition (DED) is an attractive additive manufacturing (AM) process for large structural components. The rapid solidification and layer-by-layer process associated with DED results in non-ideal microstructures, such as large grains with strong crystallographic textures. These non-ideal microstructures can lead to severe anisotropy in the mechanical properties. Despite these challenges, DED has been identified as a potential solution for the manufacturing of near net shape Ti-6Al-4V preforms, replacing lost casting and forging capabilities. Two popular wire-based directed energy deposition (W-DED) processes were considered for the manufacturing of Ti-6Al-4V with assessments on their respective metallurgical and mechanical properties, as compared to a conventionally processed material. The two W-DED processes explored were wire arc additive manufacturing (WAAM) and electron beam additive manufacturing (EBAM). High throughput inspection and tensile testing procedures were utilized to generate statistically relevant data sets related to each process and sample orientation. The 2 AM technologies produced material with remarkably different microstructures and mechanical properties. Results revealed key differences in strength and ductility for the two disparate processes which were found to be related to differences in the metallurgical properties.
The potential advantages of AM (e.g. weight reduction, novel geometries) are well understood within a systems context. However, adoption of AM at the system level has been slow due to the relative uncertainty in the final material properties, which leaves capabilities and/or performance gains unrealized. Utilizing remelt strategies it may be possible to expand the available process window to provide densities and microstructures beyond what is capable with standard scan strategies. This work explored remelting strategies for 316L stainless steel to tailor grain size and increase density. Twelve scan strategies were explored experimentally and computationally to understand the limitations of remelt strategies and the robustness of the current simulation package. Results show tailoring of grain size, density, and texture is achievable through remelting and several key lessons learned were made to improve the texture evaluation through simulation.
Stockpile stewardship requires accurate and predictive models relying on the generation of extreme environments which is both incredibly difficult and profoundly necessary. Next generation pulsed power facilities (NGPPF), where these environments are created, may require a paradigm shift in equipment engineering/manufacture to fulfill this need. Therefore, this research aims to investigate the limitations, capabilities and efficacy of leveraging advancements in the field of additive manufacturing (AM) in order to produce novel power flow components for NGPPFs. This work focused on commercial 3D metal AM equipment producing several prototypes addressing prescient needs/shortcomings, and a technique wherein a lightweight polymer core is metalized. Ultimately, commercial 3D metal AM is considered a viable path forward but would require a sizeable investment and does not currently support the scale and complexity necessary for NGPPFs. Moreover, initial results from our composite technique are promising and is considered a realizable path forward given further investigation.
Refractory High Entropy Alloys (RHEAs) and Refractory Complex Concentrated Alloys (RCCAs) are high-temperature structural alloys ideally suited for use in harsh environments. While these alloys have shown promising structural properties at high temperatures that exceed the practical limits of conventional alloys, such as Ni-based superalloys, exploration of the complex phase-space of these materials remains a significant challenge. We report on a high-throughput alloy processing and characterization methodology, leveraging laser-based metal additive manufacturing (AM) and mechanical testing techniques, to enable rapid exploration of RHEAs/RCCAs. We utilized in situ alloying and compositional grading, unique to AM processing, to rapidly-produce RHEAs/RCCAs using readily available and inexpensive commercial elemental powders. We demonstrate this approach with the MoNbTaW alloy system, as a model material known for having exceptionally high strength at elevated temperature when processed using conventional methods (e.g., casting). Microstructure analysis, chemical composition, and strain rate dependent hardness of AM-processed material are presented and discussed in the context of understanding the structure-properties relationships of RHEAs/RCCAs.
Residual stress is a common result of manufacturing processes, but it is one that is often overlooked in design and qualification activities. There are many reasons for this oversight, such as lack of observable indicators and difficulty in measurement. Traditional relaxation-based measurement methods use some type of material removal to cause surface displacements, which can then be used to solve for the residual stresses relieved by the removal. While widely used, these methods may offer only individual stress components or may be limited by part or cut geometry requirements. Diffraction-based methods, such as X-ray or neutron, offer non-destructive results but require access to a radiation source. With the goal of producing a more flexible solution, this LDRD developed a generalized residual stress inversion technique that can recover residual stresses released by all traction components on a cut surface, with much greater freedom in part geometry and cut location. The developed method has been successfully demonstrated on both synthetic and experimental data. The project also investigated dislocation density quantification using nonlinear ultrasound, residual stress measurement using Electronic Speckle Pattern Interferometry Hole Drilling, and validation of residual stress predictions in Additive Manufacturing process models.
Intermetallic alloys possess exceptional soft magnetic properties, including high permeability, low coercivity, and high saturation induction, but exhibit poor mechanical properties that make them impractical to bulk process and use at ideal compositions. We used laser-based Additive Manufacturing to process traditionally brittle Fe–Co and Fe–Si alloys in bulk form without macroscopic defects and at near-ideal compositions for electromagnetic applications. The binary Fe–50Co, as a model material, demonstrated simultaneous high strength (600–700 MPa) and high ductility (35%) in tension, corresponding to a ∼300% increase in strength and an order-of-magnitude improvement in ductility relative to conventionally processed material. Atomic-scale toughening and strengthening mechanisms, based on engineered multiscale microstructures, are proposed to explain the unusual combination of mechanical properties. This work presents an instance in which metal Additive Manufacturing processes are enabling, rather than limiting, the development of higher-performance alloys.
This study investigates the mechanical and corrosion properties of as-built and annealed equiatomic CoCrFeMnNi alloy produced by laser-based directed energy deposition (DED) Additive Manufacturing (AM). The high cooling rates of DED produced a single-phase, cellular microstructure with cells on the order of 4 μm in diameter and inter-cellular regions that were enriched in Mn and Ni. Annealing created a chemically homogeneous recrystallized microstructure with a high density of annealing twins. The average yield strength of the as-built condition was 424 MPa and exceeded the annealed condition (232 MPa), however; the strain hardening rate was lower for the as-built material stemming from higher dislocation density associated with DED parts and the fine cell size. In general, the yield strength, ultimate tensile strength, and elongation-to-failure for the as-built material exceeded values from previous studies that explored other AM techniques to produce the CoCrFeMnNi alloy. Ductile fracture occurred for all specimens with dimple initiation associated with nanoscale oxide inclusions. The breakdown potential (onset of pitting corrosion) was similar for the as-built and annealed conditions at 0.40 VAg/AgCl when immersed in 0.6 M NaCl. Pit morphology/propagation for the as-built condition exhibited preferential corrosion of inter-cellular Ni/Mn regions leading to a tortuous pit bottom and cover, while the annealed conditions pits resembled lacy pits similar to 304 L steel. A passive oxide film depleted in Cr cations with substantial incorporation of Mn cations is proposed as the primary mechanism for local corrosion susceptibility of the CoCrFeMnNi alloy.
Control of the atomic structure, as measured by the extent of the embrittling B2 chemically ordered phase, is demonstrated in intermetallic alloys through additive manufacturing (AM) and characterized using high fidelity neutron diffraction. As a layer-by-layer rapid solidification process, AM was employed to suppress the extent of chemically ordered B2 phases in a soft ferromagnetic Fe-Co alloy, as a model material system of interest to electromagnetic applications. The extent of atomic ordering was found to be insensitive to the spatial location within specimens and suggests that the thermal conditions within only a few AM layers were most influential in controlling the microstructure, in agreement with the predictions from a thermal model for welding. Analysis of process parameter effects on ordering found that suppression of B2 phase was the result of an increased average cooling rate during processing. AM processing parameters, namely interlayer interval time and build velocity, were used to systematically control the relative fraction of ordered B2 phase in specimens from 0.49 to 0.72. Hardness of AM specimens was more than 150% higher than conventionally processed bulk material. Implications for tailoring microstructures of intermetallic alloys are discussed.
This report summarizes the data analysis activities that were performed under the Born Qualified Grand Challenge Project from 2016 - 2018. It is meant to document the characterization of additively manufactured parts and processes for this project as well as demonstrate and identify further analyses and data science that could be done relating material processes to microstructure to properties to performance.