Publications

Results 96801–96825 of 100,993

Search results

Jump to search filters

High temperature surface degradation of III-V nitrides

Journal of Vacuum Science and Technology B: Microelectronics and Nanometer Structures

Zolper, J.C.

The surface stoichiometry, surface morphology, and electrical conductivity of AlN, GaN, InN, InGaN, and InAlN were examined at rapid thermal annealing temperatures up to 1150 °C. The sheet resistance of the AlN dropped steadily with annealing, but the surface showed signs of roughening only above 1000 °C. Auger electron spectroscopy (AES) analysis showed little change in the surface stoichiometry even at 1150 °C. GaN root mean square (rms) surface roughness showed an overall improvement with annealing, but the surface became pitted at 1000 °C, at which point the sheet resistance also dropped by several orders of magnitude, and AES confirmed a loss of N from the surface. The InN surface had roughened considerably even at 650 °C, and scanning electron microscopy showed significant degradation. In contrast to the binary nitrides, the sheet resistance of InAlN was found to increase by ∼102 from the as grown value (3.2×10-3 Ω cm) after annealing at 800 °C and then remain constant up to 1000 °C, while that of InGaN increased by two orders of magnitude between 700 and 900 °C. The rms roughness increased above 800 and 700 °C, respectively, for InAlN and InGaN samples. In droplets began to form on the surface at 900 °C for InAlN and at 800 °C for InGaN, and then evaporate at 1000 °C, leaving pits. AES analysis showed a decrease in the N concentration in the top 500 Å of the sample for annealing ≥800 °C in both materials. © 1996 American Vacuum Society.

More Details

Photovoltaic lighting system performance

Conference Record of the IEEE Photovoltaic Specialists Conference

Hund, Thomas D.

The performance of 21 PV-powered low pressure sodium lighting systems on a multi-use pathway has been documented in this paper. Specific areas for evaluation include the constant voltage and on/off PV charge controllers, flooded deep-cycle lead-antimony and valve regulated lead-acid (VRLA) gel batteries, low pressure sodium ballasts and lights, and vandal resistant PV modules. The PV lighting system lessons learned and maintenance intervals have been documented over the past 2.5-years. The above performance data has shown that with careful hardware selection, installation, and maintenance intervals the PV lighting systems will operate reliably.

More Details

Synthesis of periodic mesoporous silica thin films

Materials Research Society Symposium - Proceedings

Anderson, M.T.

We have synthesized periodic mesoporous silica thin films (PMSTF) from homogeneous solutions. To synthesize the films a thin layer of a pH = 7 micellar coating solution that contains TMOS is dip- or spin-coated onto silicon wafers, borosilicate glass, or quartz substrates. Ammonia gas is diffused into the solution and causes rapid hydrolysis and condensation of the TMOS and the formation of periodic mesoporous thin films within approximately 10 seconds. The combination of homogeneous solutions and rapid product formation maximizes the concentration of desired product and provides a controlled, predictable microstructure. The films have been made continuous and crack-free by optimizing initial silica concentration and film thickness.

More Details

Techniques to obtain orbital debris encounter speeds in the laboratory

Engineering, Construction, and Operations in Space V

Chhabildas, L.C.

Understanding high-pressure material behavior is crucial to address the physical processes associated with a variety of hypervelocity impact events related to space sciences such as orbital-debris impact on a debris shield. At very high impact velocities material properties will be dominated by phase-changes, such as melting or vaporization, which cannot be achieved at lower impact velocities. Development of well-controlled and repeatable hypervelocity launch capabilities is the first step necessary to improve our understanding of material behavior at extreme pressures and temperatures not currently available using conventional two-stage light-gas gun techniques. In this paper, techniques used to extend the launch capabilities of a two-stage light gas gun to 16 km/s are described. It is anticipated that this technology will be useful in testing, evaluating, and design of various debris shields proposed for use with many different spacecrafts before deployment. © 1996 American Society of Civil Engineers.

More Details

Preparation of microporous films with sub nanometer pores and their characterization using stress and FTIR measurements

Materials Research Society Symposium - Proceedings

Samuel, J.

We have used a novel technique, measurement of stress isotherms in microporous thin films, as a means of characterizing porosity. The stress measurement was carried out by applying sol-gel thin films on a thin silicon substrate and monitoring the curvature of the substrate under a controlled atmosphere of various vapors. The magnitude of macroscopic bending stress developed in microporous films depends on the relative pressure and molar volume of the adsorbate and reaches a value of 180 MPa for a relative vapor pressure, P/Po = 0.001, of methanol. By using a series of molecules, and observing both the magnitude and the kinetics of stress development while changing the relative pressure, we have determined the pore size of microporous thin films. FTIR measurements were used to acquire adsorption isotherms and to compare pore emptying to stress development, about 80% of the change in stress takes place with no measurable change in the amount adsorbed. We show that for sol-gel films, pore diameters can be controlled in the range of 5-8 angstroms by `solvent templating'.

More Details

ECR etching of GaP, GaAs, InP, and InGaAs in Cl2/Ar, Cl2/N2, BCl3/Ar, and BCl3/N2

Materials Research Society Symposium - Proceedings

Shul, Randy J.

Electron cyclotron resonance (ECR) etching of GaP, GaAs, InP, and InGaAs are reported as a function of percent chlorine-containing gas for Cl2/Ar, Cl2/N2, BCl3/Ar, and BCl3/N2 plasma chemistries. GaAs and GaP etch rates were faster than InP and InGaAs, independent of plasma chemistry due to the low volatility of the InClx etch products. GaAs and GaP etch rates increased as %Cl2 was increased for Cl2/Ar and Cl2/N2 plasmas. The GaAs and GaP etch rates were much slower in BCl3-based plasmas due to lower concentrations of reactive Cl, however enhanced etch rates were observed in BCl3/N2 at 75% BCl3. Smooth etched surfaces were obtained over a wide range of plasma chemistries.

More Details

Complementary HFET technology for low-power mixed-mode applications

Materials Research Society Symposium - Proceedings

Baca, Albert G.

Development of a complementary heterostructure field effect transistor (CHFET) technology for low-power, mixed-mode digital-microwave applications is presented. An earlier digital CHFET technology with independently optimizable transistors which operated with 319 ps loaded gate delays at 8.9 fJ is reviewed. Then work demonstrating the applicability of the digital nJFET device as a low-power microwave transistor in a hybrid microwave amplifier without any modification to the digital process is presented. A narrow band amplifier with a 0.7 × 100 μm nJFET as the active element was designed, constructed, and tested. At 1 mW operating power, the amplifier showed 9.7 dB of gain at 2.15 GHz and a minimum noise figure of 2.5 dB. In addition, next generation CHFET transistors with sub 0.5 μm gate lengths were developed. Cutoff frequencies, ft of 49 GHz and 11.5 GHz were achieved for n- and p-channel FETs with 0.3 and 0.4 μm gates, respectively. These FETs will enable both digital and microwave circuits with enhanced performance.

More Details

A model of meteoroid atmospheric entry with implications for the NEO hazard and the impact of comet shoemaker-levy 9 on jupiter

Engineering, Construction, and Operations in Space V

Crawford, David A.

A new semi-Analytical model describing the entry and deformation of meteoroids entering planetary atmospheres has been developed and calibrated against numerical simulations performed using the CTH shock-physics computational hydrocode. The model starts with the classical treatment of meteoroid ablation which is modified to include an explicit treatment of energy conservation during the ablative process. This is reconciled with terrestrial observations by modeling the formation of a vapor/debris layer (the visible bolide) surrounding the central meteoroid. A mechanical deformation model based on long-wavelength hydrodynamic instability growth is added and calibrated against numerical simulations performed with CTH. The analytical model provides initial conditions for numerical fireball simulations which are compared with observations of the Comet Shoemaker-Levy 9 impact on Jupiter and can be used to assess the terrestrial impact hazard. © 1996 American Society of Civil Engineers.

More Details

Many-body effects in a semiconductor microcavity laser: experiment and theory

Conference on Quantum Electronics and Laser Science (QELS) - Technical Digest Series

Crawford, M.H.; Choquette, K.D.; Chow, W.W.; Schneider Jr., R.P.

This paper describes a study of the underlying physical mechanisms governing the threshold properties of a VCSEL. In particular, it theoretically and experimentally evaluates the mechanisms that effect the threshold properties as a function of emission wavelength. Other important issues, such as the dependence of the threshold properties on microcavity dimensions, we discussed.

More Details

Magnetotunneling absorption in double quantum wells

Superlattices and Microstructures

Lyo, Sungkwun K.

Tunneling absorption is calculated in weakly-coupled n-type asymmetric double quantum wells in an in-plane magnetic field using a linear response theory. Tunneling absorption of photons occurs between the ground sublevels of the quantum wells. We show that the absorption threshold, the resonance energy of absorption, and the linewidth depend sensitively on the magnetic field and the temperature. © 1996 Academic Press Limited.

More Details

Integrated decoupling capacitors using Pb(Zr,Ti)O3 thin films

Materials Research Society Symposium - Proceedings

Dimos, Duane B.

Thin-film decoupling capacitors based on ferroelectric (Pb,La)(Zr,Ti)O3 films are being developed for use in advanced packaging applications. The increased integration that can be achieved by replacing surface-mount capacitors should lead to decreased package volume and improved high-speed performance. For this application, chemical solution deposition is an appropriate fabrication technique since it is a low-cost, high-throughput process. The use of relatively thick Pt electrodes (approximately 1 μm) to minimize series resistance and inductance is a unique aspect to fabricating these devices. In addition, the important electrical properties are discussed, with particular emphasis on lifetime measurements, which suggest that resistance degradation will not be a severe limitation on device performance. Finally, some of the work being done to develop methods of integrating these thin-film capacitors with ICs and MCMs is presented.

More Details

RF magnetron sputter-deposition of La0.5Sr0.5CoO3//Pt composite electrodes for Pb(Zr,Ti)O3 thin film capacitors

Materials Research Society Symposium - Proceedings

Raymond, M.V.

La0.5Sr0.5CoO3 (LSCO) thin films have been deposited, using RF magnetron sputter-deposition for use as an electrode material for Pb(Zr,Ti)O3 (PZT) thin film capacitors. The effect of the O2:Ar sputter gas ratio during deposition, on the LSCO film properties was investigated. It was found that the resistivity of the LSCO films deposited at ambient temperature decreases as the O2:Ar ratio was increased for both the as-deposited and annealed films. In addition, it was found that thin overlayers of LSCO tend to stabilize the underlying Pt//Ti electrode structure during subsequent thermal processing. The LSCO//Pt//Ti composite electrode stack has a low resistivity and provides excellent fatigue performance for PZT capacitors. Furthermore, the LSCO//Pt//Ti electrode sheet resistance does not degrade with annealing temperature and the electrode does not display hillock formation. Possible mechanisms for the stabilization of the Pt//Ti electrode with LSCO overlayers will be discussed.

More Details

Viscosity of concentrated suspensions of sphere/rod mixtures

Chemical Engineering Communications

Mondy, Lisa A.

The relative viscosity of concentrated suspensions of mixtures of rodlike and spherical particles are measured by falling-ball rheometry. The suspensions are well mixed and homogeneous in the sense that the particles are well dispersed and the rods are randomly oriented. For a constant total volume fraction of solids, the addition of spheres to suspensions of rods results in large decrease in the relative viscosity of the suspension. In these experiments the length of the suspended rods is approximately 10 times the diameter of the suspended spheres. Due to this difference in the characteristic sizes of the two types of particles, the spheres may be considered as part of the suspending homogeneous continuum. A simple model based on this physical picture, after Farris [1968], is very successful in predicting the relative viscosity of the mixed suspensions.

More Details

Near-plastic threshold indentation and the residual stress in thin films

Materials Research Society Symposium - Proceedings

Houston, Jack E.

In recent studies, we used the Interfacial Force Microscope in a nanoindenter mode to survey the nanomechanical properties of Au films grown on various substrates. Quantitative tabulations of the indentation modulus and the maximum shear stress at the plastic threshold showed consistent values over individual samples but a wide variation from substrate to substrate. These values were compared with film properties such as the surface roughness, average grain size and interfacial adhesion and no correlation was found. However, in a subsequent analysis of the results, we found consistencies which support the integrity of the data and point to the fact that the results are sensitive to some property of the various film/substrate combinations. In the present paper, we discuss these consistencies and show recent measurements which strongly suggest that the property that is being probed is the residual stress in the films caused by their interaction with the substrate surfaces.

More Details

Space applications of the MITS electron-photon monte carlo transport code system

IEEE Transactions on Nuclear Science

Kensek, R.P.; Lorence, L.J.; Halbleib, J.A.; Morel, J.E.

The MITS multigroup/continuous-energy electron-photon Monte Carlo transport code system has matured to the point that it is capable of addressing more realistic three-dimensional adjoint applications. It is first employed to efficiently predict point doses as a function of source energy for simple threedimensional experimental geometries exposed to planar sources of monoenergetic electrons up to 4. 0 MeV due to simulated uniform isotropic fluences. Results are in very good agreement with experimental data. It is then used to efficiently simulate dose to a detector in a subsystem of a GPS satellite from the natural electron environment, employing a relatively complex model of the satellite. The capability for survivability analysis of space systems is demonstrated, and results are obtained with and without variance reduction. © 1996 IEEE.

More Details

Microscopic theory of gain in a group-III nitride strained quantum well laser

Conference Proceedings - Lasers and Electro-Optics Society Annual Meeting-LEOS

Chow, Weng W.

The study of gain properties in group-III nitride quantum wells is complicated by several factors. In view of this, an approach is presented that involves a first-principles bandstructure calculation, the results of which are incorporated into a microscopic laser theory. The band structure calculation applies a density-functional method. This method provides a single analytical model for computing the group-II nitride material properties, thus ensuring consistency in the values for the different bandstructure parameters, and circumventing the discrepancies present in the literature due to different experimental conditions, or different computational methods. With a complete set of the relevant material parameters, it is possible to study the effects of strain and quantum confinement.

More Details

Monochromatic imaging studies of sustained metal vapor arcs burning on 150 mm diameter molten iron electrodes

International Symposium on Discharges and Electrical Insulation in Vacuum, ISDEIV

Williamson, Rodney L.

Monochromatic imaging was used to investigate the excited-state density distributions of Fe and Fe+ in the inter-electrode gap region of a 3,100 A dc metal vapor arc burning between molten iron surfaces in a vacuum arc furnace. Multiple images were acquired at four wavelengths. The images were corrected and Abel inverted to yield the absolute radial intensity distributions for Fe and Fe+ in the inter-electrode gap region. The results show a structured, axisymmetric plasma consisting of a high density 'core' of Fe+ emitters centered between the electrode surfaces situated against a relatively broad, flat excited-state Fe distribution.

More Details

Optimization of reliability allocation strategies through use of genetic algorithms

6th Symposium on Multidisciplinary Analysis and Optimization

Campbell, J.E.; Painton, L.A.

This paper examines a novel optimization technique called genetic algorithms and its application to the optimization of reliability allocation strategies. Reliability allocation should occur in the initial stages of design, when the objective is to determine an optimal breakdown or allocation of reliability to certain components or subassemblies in order to meet system objectives. The reliability allocation optimization is applied to the design of a cluster tool, a highly complex piece of equipment used in semiconductor manufacturing. The problem formulation is presented, including decision variables, performance measures and constraints, and genetic algorithm parameters. Piecewise “effort curves” specifying the amount of effort required to achieve a certain level of reliability for each component or subassembly are defined. The genetic algorithm evolves or picks those combinations of “effort” or reliability levels for each component which optimize the objective of maximizing Mean Time Between Failures while staying within a budget. The results show that the genetic algorithm is very efficient at finding a set of robust solutions. A time history of the optimization is presented, along with histograms of the solution space fitness, MTBF, and cost for comparative purposes.

More Details

Failure Analysis of a Half-Micron CMOS IC Technology

Conference Proceedings from the International Symposium for Testing and Failure Analysis

Liang, A.Y.

We present the results of recent failure analysis of an advanced, 0.5 um, fully planarized, triple metallization CMOS technology. A variety of failure analysis (FA) tools and techniques were used to localize and identify defects generated by wafer processing. These include light (photon) emission microscopy (LE), fluorescent microthermal imaging (FMI), focused ion beam cross sectioning, SEM/voltage contrast imaging, resistive contrast imaging (RCI), and e-beam testing using an IDS-5000 with an HP 82000. The defects identified included inter- and intra-metal shorts, gate oxide shorts due to plasma processing damage, and high contact resistance due to the contact etch and deposition process. Root causes of these defects were determined and corrective action was taken to improve yield and reliability.

More Details

MULTI-LEVEL POLYSILICON SURFACE-MICROMACHINING TECHNOLOGY: APPLICATIONS AND ISSUES

ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE)

Sniegowski, Jeffry J.

Polysilicon surface micromachining is a technology for manufacturing Micro-Electro-Mechanical Systems (MEMS) which has, as its basis, the manufacturing methods and tool sets used to manufacture the integrated electronic circuit. This paper describes a three-level mechanical-polysiiicon surface-micromachining technology and includes a discussion of the advantages of this level of process complexity along with issues which affect device fabrication and performance. Historically, the primary obstacles to multi-level polysilicon fabrication were related to the severe wafer topography generated by the repetition of film depositions and etching. The introduction of Chemical Mechanical Polishing (CMP) to surface micromachining has largely removed these issues and opened significant avenues for device complexity. Several examples of three-level devices with the benefits of CMP are presented. Of primary hindrance to the widespread use of polysilicon surface micromachining, and in particular microactuation mechanisms, are issues related to the device surfaces. The closing discussion examines the potential of several latter and postfabrication processes to circumvent or to directly alleviate the surface problems.

More Details

Nature of the green luminescent center in zinc oxide

Materials Research Society Symposium - Proceedings

Warren, William L.

We apply a number of complementary characterization techniques including electron paramagnetic resonance, optical absorption, and photoluminescence spectroscopies to characterize a wide range of different ZnO phosphor powders. We generally observe a good correlation between the 510-nm green emission intensity and the density of paramagnetic isolated oxygen vacancies. In addition, both quantities are found to peak at a free-carrier concentration ne, of about 1.4×1018 cm-3. We also find that the green emission intensity can be strongly influenced by free-carrier depletion at the particle surface, especially for small particles and/or low doping. Our data suggest that the green PL in ZnO phosphors is due to the recombination of electrons in singly occupied oxygen vacancies with photoexcited holes in the valence band.

More Details

Invariant patterns in crystal lattices: Implications for protein folding algorithms

Lecture Notes in Computer Science (including subseries Lecture Notes in Artificial Intelligence and Lecture Notes in Bioinformatics)

Hart, William E.; Istrail, Sorin

Crystal lattices are infinite periodic graphs that occur naturally in a variety of geometries and which are of fundamental importance in polymer science. Discrete models of protein folding use crystal lattices to define the space of protein conformations. Because various crystal lattices provide discretizations of the same physical phenomenon, it is reasonable to expect that there will exist "invariants" across lattices that define fundamental properties of the protein folding process; an invariant defines a property that transcends particular lattice formulations. This paper identifies two classes of invariants, defined in terms of sublattices that are related to the design of algorithms for the structure prediction problem. The first class of invariants is used to define a master approximation algorithm for which provable performance guarantees exist. This algorithm can be applied to generalizations of the hydrophobic-hydrophilic model that have lattices other than the cubic lattice, including most of the crystal lattices commonly used in protein folding lattice models. The second class of invariants applies to a related lattice model. Using these invariants, we show that for this model the structure prediction problem is intractable across a variety of threedimensional lattices. It turns out that these two classes of invariants are respectively sublattices of the two-and three-dimensional square lattice. As the square lattices are the standard lattices used in empirical protein folding studies, our results provide a rigorous confirmation of the ability of these lattices to provide insight into biological phenomenon. Our results are the first in the literature that identify algorithmic paradigms for the protein structure prediction problem that transcend particular lattice formulations.

More Details

GOMA - A full-Newton finite element program for free and moving boundary problems with coupled fluid/solid momentum, energy, mass, and chemical species transport: User`s guide

Schunk, Peter R.

GOMA is a two- and three-dimensional finite element program which excels in analyses of manufacturing processes, particularly those involving free or moving interfaces. Specifically, the full-Newton-coupled heat, mass, momentum, and pseudo-solid mesh motion algorithm makes GOMA ideally suited for simulating processes in which the bulk fluid transport is closely coupled to the interfacial physics. Examples include, but are not limited to, coating and polymer processing flows, soldering, crystal growth, and solid-network or solution film drying. The code is based on the premise that any boundary can be (1) moving or free, with an apriori unknown position dictated by the distinguishing physics, (2) fixed, according to a global analytical representation, or (3) moving in time and space under user-prescribed kinematics. The goal is to enable the user to predict boundary position or motion simultaneously with the physics of the problem being analyzed and to pursue geometrical design studies and fluid-structure interaction problems. The moving mesh algorithm treats the entire domain as a computational Lagrangian solid that deforms subject to the physical principles which dictate boundary position. As an added benefit, the same Lagrangian solid mechanics can be exploited to solve multi-field problems for which the solid motion and stresses interact with other transport phenomena, either within the same material phase (e.g. shrinking coating) or in neighboring material phases (e.g. flexible blade coating). Thus, analyses of many fluid-structure interaction problems and deformable porous media problems are accessible. This document serves as a user`s guide and reference for GOMA and provides a brief overview of GOMA`s capabilities, theoretical background, and classes of problems for which it is targeted.

More Details

Solution of problems with material nonlinearities with a coupled finite element/boundary element scheme using an iterative solver. Yucca Mountain Site Characterization Project

Koteras, J.R.

The prediction of stresses and displacements around tunnels buried deep within the earth is an important class of geomechanics problems. The material behavior immediately surrounding the tunnel is typically nonlinear. The surrounding mass, even if it is nonlinear, can usually be characterized by a simple linear elastic model. The finite element method is best suited for modeling nonlinear materials of limited volume, while the boundary element method is well suited for modeling large volumes of linear elastic material. A computational scheme that couples the finite element and boundary element methods would seem particularly useful for geomechanics problems. A variety of coupling schemes have been proposed, but they rely on direct solution methods. Direct solution techniques have large storage requirements that become cumbersome for large-scale three-dimensional problems. An alternative to direct solution methods is iterative solution techniques. A scheme has been developed for coupling the finite element and boundary element methods that uses an iterative solution method. This report shows that this coupling scheme is valid for problems where nonlinear material behavior occurs in the finite element region.

More Details

Perspectives on plant vulnerabilities & other plant and containment improvements

Camp, Susan E.

The primary goal of the Individual Plant Examination (IPE) Program was for licensees to identify plant-unique vulnerabilities and actions to address these vulnerabilities. A review of these vulnerabilities and plant improvements that were identified in the IPEs was performed as part of the IPE Insights Program sponsored by the U.S. Nuclear Regulatory Commission (NRC). The purpose of this effort was to characterize the identified vulnerabilities and the impact of suggested plant improvements. No specific definition for {open_quotes}vulnerability{close_quotes} was provided in NRC Generic Letter 88-20 or in the subsequent NRC IPE submittal guidance documented in NUREG-1335. Thus licensees were left to use their own definitions. Only 20% of the plants explicitly stated that they had vulnerabilities. However, most licensees identified other plant improvements to address issues not explicitly classified as vulnerabilities, but pertaining to areas in which overall plant safety could potentially be increased. The various definitions of {open_quotes}vulnerability{close_quotes} used by the licensees, explicitly identified vulnerabilities, proposed plant improvements to address these vulnerabilities, and other plant improvements are summarized and discussed.

More Details
Results 96801–96825 of 100,993
Results 96801–96825 of 100,993
Top