Publications

We are currently evaluating large capacity (20 - 40 Ah) Bluestar (cylindrical) and Yardney (prismatic) Li-ion cells for their electrical and electrochemical performance characteristics at different temperatures. The cell resistance was nearly constant from room temperature to -20{degrees}C but increased by over 10 times at -40{degrees}C. The specific energy and power as well as the energy density and power density are high and didn't reach a plateau even at the highest discharge rates tested. For example, the prismatic Li-ion cells gave close to 280 Wh l{sup -1} at 4-amp discharge and 249 Wh l{sup -1} at 20-amp discharge at room temperature. For the same current range the specific power values are 102 Wh kg{sup -1} and 91 Wh kg{sup -1}. Cycle life and other electrical and electrochemical properties of the cells will be presented.

The nature of this work was to develop the physics and chemistry base for understanding molecular-scale lubricants used to reduce of friction- and adhesion-induced failure in silicon micromachines (MEMS). We acquired this new knowledge by tailoring the molecular properties of the lubricants, applying local probes that can directly monitor the response of lubricants in contact conditions, and evaluating the performance of model lubricants MEMS devices. Model lubricants under investigation were the silane coupling agents that form monolayer films on native oxide silicon surfaces, which is the substrate in MEMS. These molecules bind via strong surface bonds and produce a layer of hydro- or fluoro-carbon chains normal to the substrate. "Tailoring" the lubricants entails modifying the chain length, the chain chemical reactivity (H or F), and the density of chain structures. Thus much effort went into understanding the surface chemistry of silane-silicon oxide coupling. With proximal probes such as atomic force microscopy (AFM), interracial force microscopy (FM), and shear force microscopy in combination with IFM, we examined the frictional and adhesive properties of the silane films with very high spatial resolution (< 100 nm) and sensitivity. MEMS structures are treated with silanes under identical conditions, and examined for friction and adhesion under operating conditions. Proper assessment of the lubricants required quantitative analysis of MEMS performance at high speeds and long operating times. Our proximal probe measurements and WS performance analyses form a very important link for future molecular dynamics simulations, that, in turn, should be able to predict MEMS performance under all conditions.

A new epoxy foam encapsulant, EF-ARIO/20, has been developed at Sandia National Laboratories (SNL) as a replacement for Ablefoam", an epoxy foam encapsulant used in the W76 Arming, Fusing, and Firing (Al%@) system. Since it contained toxic ingredients including a known carcinogen, Ablefoarn" is no longer commercially available. It has been demonstrated by scanning electron microscopy (SEM) that the microstructure of the new epoxy foam is similar to that of Ablefoam@. Mechanical properties of tensile and compressive strength, and tensile and compressive modulus, and thermal properties of glass transition temperature (.TJ, and coefficient of thermal expansion (CTE) have been measured for the new foam. Electrical properties of dielectric constant, dissipation factors, volume resistivity, and dielectric strength were also measured. These property measurements are comparable to those of Ablefoam@. Development and characterization of the new foam will be discusse~ and a comparison of mechanical, thermal, and electrical properties for the new epoxy foam and Ablefoam@ will be reported.

This report examines methods of mobile communications with an emphasis on mobile computing and wireless communications. Many of the advances in communications involve the use of Internet Protocol (IP), Asynchronous Transfer Mode (ATM), and ad hoc network protocols. However, many of the advances in these protocols have been focused on wired communications. Recently much focus has been directed at advancing communication technology in the area of mobile wireless networks. This report discusses various protocols used in mobile communications and proposes a number of extensions to existing protocols. A detailed discussion is also included on desirable protocol characteristics and evaluation criteria. In addition, the report includes a discussion on several network simulation tools that maybe used to evaluate network protocols.

The proposed "catalytic membrane sensor" (CMS) was developed to generate a device which would selectively identify a specific reagent in a complex mixture of gases. This was to be accomplished by modifying an existing Hz sensor with a series of thin films. Through selectively sieving the desired component from a complex mixture and identifying it by decomposing it into Hz (and other by-products), a Hz sensor could then be used to detect the presence of the select component. The proposed "sandwich-type" modifications involved the deposition of a catalyst layered between two size selective sol-gel layers on a Pd/Ni resistive Hz sensor. The role of the catalyst was to convert organic materials to Hz and organic by-products. The role of the membraneo was to impart both chemical specificity by molecukir sieving of the analyte and converted product streams, as well as controlling access to the underlying Pd/Ni sensor. Ultimately, an array of these CMS elements encompassing different catalysts and membranes were to be developed which would enable improved selectivity and specificity from a compiex mixture of organic gases via pattern recognition methodologies. We have successfully generated a CMS device by a series of spin-coat deposited methods; however, it was determined that the high temperature required to activate the catalyst, destroys the sensor.

Abstract not provided.

The authors have produced milliwatts of blue light from a diode-pumped, multiple-quantum-well semiconductor laser. This compact source has a pump-to-blue optical efficiency >1%.

This paper describes a modeling technique for single-agent reactive systems, that is influenced by the modeling paradigm of Parnas as well as by the synchronous paradigms of LUSTRE and ESTEREL. In this paradigm, single-agent reactive systems are modeled in a universe having a discrete clock. This discretization of time greatly reduces the temporal complexity of the model. He believes that the advantage of this reduction in temporal complexity is that the resulting model is in many ways better suited to automated software construction and analysis techniques (e.g., deductive synthesis, transformation, and verification) than models that are based on continuous representations of time.

Rheology and deposition behavior of four commercially available thick-film inks and an aqueous alumina slurry were investigated using two different slurry-based deposition systems. The first of these deposition systems, a Micropen, is a commercially available system designed for the deposition of electronic thick film circuits. The second system, referred to as a Robocaster, is a developmental system designed to build thick or structural parts. Slurry rheology was seen to have a minor effect on deposition behavior and the bead shape when deposited using the Micropen. The deposition behavior was instead dominated by drying rate; too rapid of a drying rate led to excessive clogging of the tip. Slurry rheology had a greater impact on the shape of beads deposited using the Robocaster. Highly viscous slurries yielded initially well-defined beads, whereas beads deposited using fluid slurries spread quickly. In both cases, significant spreading occurred with time. These observations only held for slurries with slow drying rates. It was observed that very fluid slurries produced well-defined beads when the drying rate was suitably high.

All US space missions involving on board nuclear material must be approved by the Office of the President. To be approved the mission and the hardware systems must undergo evaluations of the associated nuclear health and safety risk. One part of these evaluations is the characterization of the source terms, i.e., the estimate of the amount, physical form, and location of nuclear material, which might be released into the environment in the event of credible accidents. This paper presents a brief overview of the source term analysis by the Interagency Nuclear Safety Review Panel for the NASA Cassini Space Mission launched in October 1997. Included is a description of the Energy Interaction Model, an innovative approach to the analysis of potential releases from high velocity impacts resulting from launch aborts and reentries.

The literature of radiation damage measurements on cadmium zinc telluride (CZT), cadmium telluride (CT), and mercuric iodide (HgI{sub 2}) is reviewed and in the case of CZT supplemented by new alpha particle data. CZT strip detectors exposed to intermediate energy (1.3 MeV) proton fluences exhibit increased interstrip leakage after 10{sup 10} p/cm{sup 2} and significant bulk leakage after 10{sup 12} p/cm{sup 2}. CZT exposed to 200 MeV protons shows a two-fold loss in energy resolution after a fluence of 5 {times} 10{sup 9} p/cm{sup 2} in thick (3 mm) planar devices but little effect in 2 mm devices. No energy resolution effects were noted from moderated fission spectrum of neutrons after fluences up to 10{sup 10} n/cm{sup 2}, although activation was evident. Exposures of CZT to 5 MeV alpha particle at fluences up to 1.5 {times} 10{sup 10} {alpha}/cm{sup 2} produced a near linear decrease in peak position with fluence and increases in FWHM beginning at about 7.5 {times} 10{sup 9} {alpha}/cm{sup 2}. CT detectors show resolution losses after fluences of 3 {times} 10{sup 9} p/cm{sup 2} at 33 MeV for chlorine-doped detectors. Indium doped material may be more resistant. Neutron exposures (8 MeV) caused resolution losses after fluences of 2 {times} 10{sup 10} n/cm{sup 2}. Mercuric iodide has been studied with intermediate energy protons (10 to 33 MeV) at fluences up to 10{sup 12} p/cm{sup 2} and with 1.5 GeV protons at fluences up to 1.2 {times} 10{sup 8} p/cm{sup 2}. Neutron exposures at 8 MeV have been reported at fluences up to 10{sup 15} n/cm{sup 2}. No radiation damage was reported under these irradiation conditions.

The efficient characterization of nonlinear systems is an important goal of vibration and model testing. The authors build a nonlinear system model based on the acceleration time series response of a single input, multiple output system. A series of local linear models are used as a template to train artificial neutral networks (ANNs). The trained ANNs map measured time series responses into states of a nonlinear system. Another NN propagates response states in time, and a third ANN inverts the original map, transforming states into acceleration predictions in the measurement domain. The technique is illustrated using a nonlinear oscillator, in which quadratic and cubic stiffness terms play a major part in the system`s response. Reasonable maps are obtained for the states, and accurate, long-term response predictions are made for data outside the training data set.

I have recently become involved in the ABET certification process under the new system - ABET 2000. This system relies heavily on concepts of Total Quality Management (TQM). It encourages each institution to define its objectives in terms of its own mission and then create a coherent program based on it. The prescribed steps in setting up the new system at an engineering institution are: o identification of constituencies G definition of mission. It is expected that the department's mission will be consistent with that of the overall institution, but containing some higher resolution language appropriate to that particular discipline of the engineering profession. o statement of objectives consistent with the mission 3G~~\vED " enumeration of desired, and preferably measurable, outcomes of the process that would ~ `=. verify satisfaction of the objectives. ~~~ 07 !398 o establish performance standards for each outcome. o creation of appropriate feedback loops to assure that the objectives are still consistent with Q$YT1 the mission, that the outcomes remain consistent with the objectives, and that the curriculum and the teaching result in those outcomes. It is my assertion that once the institution verbalizes a mission, enumerated objectives naturally flow from that mission. (We shall try to demonstrate by example.) Further, if the mission uses the word "engineer", one would expect that word also to appear in at least one of the objectives. The objective of producing engineers of any sort must -by decree - involve the presence of the ABET criteria in the outcomes list. In other words, successful satisfaction of the ABET items a-k are a necessary subset of the measure of success in producing engineers. o We shall produce bachelor level engineers whose training in the core topics of chemical (or electrical, or mechanical) engineering is recognized to be among the best in the nation. o We shall provide an opportunity for our students to gain a significant exposure to biomedical topics and the integration of those topics with chemical (electrical or mechanical) engineering. o We shall provide unique opportunities for our students to work with clinicians and researchers in hospitals and other medical institutions. combined criteria a-k of ABET and 1-6 of AICHE (or IEEE or ASME) in some sensible manner. Here I have just estimated the number of distinct criteria that would be extracted from the AICHE paragraphs. These criteria are necessarily included because of the objective to producing chemical (electrical or mechanical) engineers. every student who desires an internship or independent study at a medical institution will be placed. a majority of our students will take either the FE exam or the M-CAT exam. demonstrating a commitment to professionalism and to life-long learning. a majority of our students will go on to graduate school or other post-graduate school. (I do not assert that this sort of outcome is appropriate to all excellent schools. In the case of this hypothetical school though, this outcome might be a reasonable expectation.) medical schools will rank our school as among the best from which to admit

We investigate the reliability If a rechargeable battery acting as the energy storage component in a photovoltaic power supply system. A model system was constructed for this that includes the solar resource, the photovoltaic power supp Iy system, the rechargeable battery and a load. The solar resource and the system load are modeled as SI ochastic processes. The photovoltaic system and the rechargeable battery are modeled deterministically, imd an artificial neural network is incorporated into the model of the rechargeable battery to simulate dartage that occurs during deep discharge cycles. The equations governing system behavior are solved simultaneously in the Monte Carlo framework and a fwst passage problem is solved to assess system reliability.

Silicon processing techniques were used to fabricate 3-D photonic lattices with band gaps in the infrared. The demonstration vehicle was a selective infrared mirror/band pass filter, a wide range of other applications are also possible.

In many situations, stand-off remote-sensing and hazard-interdiction techniques over realistic operational areas are often impractical "and difficult to characterize. An alternative approach is to implement an adap- tively deployable array of sensitive agent-specific devices. Our group has been studying the collective be- havior of an autonomous, multi-agent system applied to chedbio detection and related emerging threat applications, The current physics-based models we are using coordinate a sensor array for mukivanate sig- nal optimization and coverage as re,alized by a swarm of robots or mobile vehicles. These intelligent control systems integrate'glob"ally operating decision-making systems and locally cooperative learning neural net- works to enhance re+-timp operational responses to dynarnical environments examples of which include obstacle avoidance, res~onding to prevailing wind patterns, and overcoming other natural obscurants or in- terferences. Collectively',tkensor nefirons with simple properties, interacting according to basic community rules, can accomplish complex interconnecting functions such as generalization, error correction, pattern recognition, sensor fusion, and localization. Neural nets provide a greater degree of robusmess and fault tolerance than conventional systems in that minor variations or imperfections do not impair performance. The robotic platforms would be equipped with sensor devices that perform opticaI detection of biologicais in combination with multivariate chemical analysis tools based on genetic and neural network algorithms, laser-diode LIDAR analysis, ultra-wideband short-pulsed transmitting and receiving antennas, thermal im- a:ing sensors, and optical Communication technology providing robust data throughput pathways. Mission scenarios under consideration include ground penetrating radar (GPR) for detection of underground struc- tures, airborne systems, and plume migration and mitigation. We will describe our research in these areas anti give a status report on our progress.

The design, growth by metal-organic chemical vapor deposition, and processing of an In{sub 0.07}Ga{sub 0.93}As{sub 0.98}N{sub 0.02} solar Al, with 1.0 ev bandgap, lattice matched to GaAs is described. The hole diffusion length in annealed, n-type InGaAsN is 0.6-0.8 pm, and solar cell internal quantum efficiencies > 70% arc obwined. Optical studies indicate that defects or impurities, from InGAsN doping and nitrogen incorporation, limit solar cell performance.

We have used the Interracial Force Microscope" to perform nanoindentations on Au single- crystal surfaces. We have observed two distinct regimes of plastic deformation which are distinguished by the magnitude of discontinuities in load relaxation. At lower stresses, relaxation occurs in small deviations from elastic behavior, while at the higher stresses they take the form of large load drops often resulting in complete relaxation of the applied load. These major events create a relatively wide plastic zone that subsequently deepens more rapidly than it widens. We discuss these findings in terms of contrasting models of dislocation processes in the two regimes.

By accurately measuring the angle of reflection of a laser beam incident on a reflective surface with a position sensitive detector, changes in the surface normal direction (slope of the surface) can be determined directly. An instrument has been built that makes repeated measurements over the surface, and uses this data to produce a grayscale image of the slope. The resolution of this system to changes in the surface normal direction is found to be better than 0.01 degrees. By focusing the Iaser beam to achieve a lateral resolution of 5 pm, the resolvable surface height change due to a variation in slope is estimated to be <1 nm.

First-principles density-functional calculations are used to study metal adsorption (Li, K, Y, Nb, Ru, Pd, Pt, Cu, Ag, Au, and Al at 1/3-4 monolayer coverages) atop 5 ~ A1203 films on Al(Ill). The oxide-metal bond is ionic at Iow coverages but, with interesting exceptions, caused by polari@i ,~-cE!vED at high coverages where the overlayer is metallic. Binding trends are explained in terms of s'imp e concepts. Increasing overlayer thickness can cause the adsorbate-oxide interface structure to than . %lEc o ~ 1998 and while some metals wet, most do not.

We developed a model for the probabilistic behavior of a rechargeable battery acting as the energy storage component in a photovoltaic power supply system. Stochastic and deterministic models are created to simulate the behavior of the system component;. The components are the solar resource, the photovoltaic power supply system, the rechargeable battery, and a load. Artificial neural networks are incorporated into the model of the rechargeable battery to simulate damage that occurs during deep discharge cycles. The equations governing system behavior are combined into one set and solved simultaneously in the Monte Carlo framework to evaluate the probabilistic character of measures of battery behavior.

A mathematical model of a spirally wound lithium/thionyl chloride primary battery has been developed ~d used for parameter estimation and design studies. The model formulation is based on the fimdarnental Consemation laws using porous electrode theory and concentrated solution theory. The model is used to estimate the difision coefficient and the kinetic parameters for the reactions at the anode and the cathode as a function of temperature. These parameters are obtained by fitting the simulated capacity and average cell voltage to experimental data over a wide range of temperatures (-55 to 49"C) and discharge loads (10 to 250 ohms). The experiments were performed on D-sized, cathode-limited, spirally wound lithium/thionyl chloride cells. The model is also used to study the effkct of cathode thickness on the cell capacity as a finction of temperature, and it was found that the optimum thickness for the cathode- limited design is temperature and load dependent.

A discrete element computer program named DMC_BLAST (Distinct Motion Code) has been under development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions. DMC_BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993). Coal seam chilling refers to the shattering of a significant portion of the coal leaving unusable fines. It is also refereed to as coal damage. Chilling is caused during a blast by a combination of explosive shock energy and movement of the adjacent rock. Chilling can be minimized by leaving a buffer zone between the bottom of the blastholes and the coal seam or by changing the blast design to decrease the powder factor or by a combination of both. Blast design in coal mine cast blasting is usually a compromise between coal damage and rock fragmentation and movement (heave). In this paper the damage to coal seams from rock movement is examined using the discrete element computer code DMC_BLAST. A rock material strength option has been incorporated into DMC_BLAST by placing bonds/links between the spherical particles used to model the rock. These bonds tie the particles together but can be broken when the tensile, compressive or shear stress in the bond exceeds the defined strength. This capability has been applied to predict coal seam damage, particularly at the toe of a cast blast where drag forces exerted by movement of the overlying rock can adversely effect the top of the coal at the bench face. A simulation of coal mine cast blasting has been performed with special attention being paid to the strength of the coal and its behavior at t he bench face during movement of the overlying material.

Sol-gel matrices are promising host materials for potential chemical and biosensor applications. Previous studies have focused on modified sol-gel routes using alkoxides for encapsulation of enzymes. However the formation of alcohol as a byproduct during hydrolysis and condensation reactions poses limitations. We report the immobilization of glucose oxidase and peroxidase in silica prepared by an aqueous route which may provide a more favorable environment for the biomolecules. A two step aqueous sol-gel procedure using sodium silicate as the precursor was developed to encapsulate the enzymes and the dye precursor, o-dianisidine. Glucose oxidase catalyzes the oxidation of glucose to give gluconic acid and hydrogen peroxide. Peroxidase then catalyzes the reaction of the dye precursor with hydrogen peroxide to produce a colored product. The kinetics of the coupled enzymatic reactions were monitored by optical spectroscopy and compared to those occurring in tetramethyl orthosilicate (TMOS) derived silica matrices developed by Yamanaka. Enhanced kinetics in the aqueous silicate matrices were related to differences in the host microstructure as elucidated by microstructural comparisons of the corresponding aerogels.

The rapid pace of change at Ike end of the 20th Century should continue unabated well into the 21st Century. The driver will be the marketplace imperative of "faster, better, cheaper." This imperative has already stimulated a revolution-in-engineering in design and manufacturing. In contrast, to date, reliability engineering has not undergone a similar level of change. It is critical that we implement a corresponding revolution-in-reliability-engineering as we enter the new millennium. If we are still using 20th Century reliability approaches in the 21st Century, then reliability issues will be the limiting factor in faster, better, and cheaper. At the heart of this reliability revolution will be a science-based approach to reliability engineering. Science-based reliability will enable building-in reliability, application-specific products, virtual qualification, and predictive maintenance. The purpose of this paper is to stimulate a dialogue on the future of reliability engineering. We will try to gaze into the crystal ball and predict some key issues that will drive reliability programs in the new millennium. In the 21st Century, we will demand more of our reliability programs. We will need the ability to make accurate reliability predictions that will enable optimizing cost, performance and time-to-market to meet the needs of every market segment. We will require that all of these new capabilities be in place prior to the stint of a product development cycle. The management of reliability programs will be driven by quantifiable metrics of value added to the organization business objectives.

High density plasma etching of GaAs, GaSb and AIGaAs was performed in IC1/Ar and lBr/Ar chemistries using an Inductively Coupled Plasma (ICP) source. GaSb and AlGaAs showed maxima in their etch rates for both plasma chemistries as a function of interhalogen percentage, while GaAs showed increased etch rates with plasma composition in both chemistries. Etch rates of all materials increased substantially with increasing rf chuck power, but rapidly decreased with chamber pressure. Selectivities > 10 for GaAs and GaSb over AlGaAs were obtained in both chemistries. The etched surfaces of GaAs showed smooth morphology, which were somewhat better with IC1/Ar than with IBr/& discharge. Auger Electron Spectroscopy analysis revealed equi-rate of removal of group III and V components or the corresponding etch products, maintaining the stoichiometry of the etched surface.

A parametric study of Inductively Coupled Plasma etching of InP, InSb, InGaP and InGaAs has been carried out in IC1/Ar and IBr/Ar chemistries. Etch rates in excess of 3.1 prrdmin for InP, 3.6 prnh-nin for InSb, 2.3 pm/min for InGaP and 2.2 ~rrdmin for InGaAs were obtained in IBr/Ar plasmas. The ICP etching of In-based materials showed a general tendency: the etch rates increased substantially with increasing the ICP source power and rf chuck power in both chemistries, while they decreased with increasing chamber pressure. The IBr/Ar chemistry typically showed higher etch rates than IC1/Ar, but the etched surface mophologies were fairly poor for both chemistries.

Reactive ion beam etching (RD3E) of GaAs, GaP, AIGaAs and GaSb was performed in a Cl2-Ar mixture using an Inductively Coupled Plasma (ICP) source. `The etch rates and yields were strongly affected by ion energy and substrate temperature. The RJBE was dominated by ion-assisted etching at <600 eV and by physical sputtering beyond 600 eV. The temperature dependence of the etch rates revealed three different regimes, depending on the substrate temperature: 1) sputtering-etch limited, 2) products-resorption limited, and 3) mass-transfer limited regions. GaSb showed the overall highest etch rates, while GaAs and AIGaAs were etched at the same rates. The etched features showed extremely smooth morphologies with anisotropic sidewalls.

Donor (S, Se and Te) and acceptor (Mg, Be and C) dopants have been implanted into GaN at doses of 3-5x1014 cm-2 and annealed at temperatures up to 1450 *C. No redistribution of any of the elements is detectable by Secondary Ion Mass Spectrometry, except for Be, which displays an apparent damage-assisted diffusion at 900 "C. At higher temperatures there is no further movement of the Be, suggesting that the point defect flux that assists motion at lower temperatures has been annealed. Effective diffusivities are <2X 1013 cm2.sec-1 at 1450 `C for each of the dopants in GaN.

All of the major acceptor (Mg, C, Be) and donor (Si, S, Se and Te) dopants have been implanted into GaN films grown on A1203 substrates. Annealing was performed at 1100- 1500 C, using AIN encapsulation. Activation percentages of >90Y0 were obtained for Si+ implantation annealed at 1400 C, while higher temperatures led to a decrease in both carrier concentration and electron mobility. No measurable redistribution of any of the implanted dopants was observed at 1450 C.

Theories for inhomogeneous fluids have focused in recent years on wetting, capillary conden- sation, and solvation forces for model systems where the surface(s) is(are) smooth homogeneous parallel plates, cylinders, or spherical drops. Unfortunately natural systems are more likely to be hetaogeneous both in surt%ce shape and surface chemistry. In this paper we discuss the conse- quences of chemical heterogeneity on wetting. Specifically, a 2-dimensional implementation of a nonlocal density functional theory is solved for a striped surface model. Both the strength and range of the heterogeneity are varied. Contact angles are calculated, and phase transitions (both the wetting transition and a local layering transition) are located. The wetting properties of the surface ase shown to be strongly dependent on the nature of the surface heterogeneity. In addition highly ordered nanoscopic phases are found, and the operational limits for formation of ordered or crystalline phases of nanoscopic extent are discussed.

Incidents of liner corrosion in nuclear power containment structures have been recorded. These incidents and concerns of other possible liner corrosion in containment have prompted an interest in determining g the capacity of a degraded containment. Finite element analyses of a typical pressurized water reactor (PWR) reinforced concrete containment with liner corrosion were conducted using the A13AQUS finite element code with the ANACAP-U nonlinear concrete constitutive model. The effect of liner corrosion on containment capacity was investigated. A loss of coolant accident was simulated by applying pressure and temperature changes to the structure without corrosion to determine baseline failure limits, followed by multiple analyses of the containment with corrosion at different locations and varying degrees of liner degradation. The corrosion locations were chosen at the base of the containment wall, near the equipment hatch, and at the midheight of the containment wall. Using a strain-based failure criterion the different scenarios were evaluated to prioritize their effect on containment capacity

As future sizes of Integrated Circuits (ICs) continue to shrink the sensitivity of these devices, particularly SRAMs and DRAMs, to natural radiation is increasing. In this paper, the Ion Beam Induced Charge Collection (IBICC) technique is utilized to simulate neutron-induced Si recoil effects in ICS. The IBICC measurements, conducted at the Sandia National Laboratories employed a 10 MeV carbon microbeam with 1pm diameter spot to scan test structures on specifically designed ICS. With the aid of layout information, an analysis of the charge collection efficiency from different test areas is presented. In the present work a 10 MeV Carbon high-resolution microbeam was used to demonstrate the differential charge collection efficiency in ICS with the aid of the IC design Information. When ions strike outside the FET, the charge was only measured on the outer ring, and decreased with strike distance from this diode. When ions directly strike the inner and ring diodes, the collected charge was localized to these diodes. The charge for ions striking the gate region was shared between the inner and ring diodes. I The IBICC measurements directly confirmed the interpretations made in the earlier work.

Abstract not provided.

Abstract not provided.

Understanding the surface heat transfer during quenching can be beneficial. Analysis to estimate the surface heat transfer from internal temperature measurements is referred to as the inverse heat conduction problem (IHCP). Function specification and gradient adjoint methods, which use a gradient search method coupled with an adjoint operator, are widely u led methods to solve the IHCP. In this paper the two methods are presented for the multidimensional case. The focus is not a rigorous comparison of numerical results. Instead after formulating the multidimensional solutions, issues associated with the numerical implementation and practical application of the methods are discussed. In addition, an experiment that measured the surface heat flux and temperatures for a transient experimental case is analyzed. Transient temperatures are used to estimate the surface heat flux, which is compared to the measured values. The estimated surface fluxes are comparable for the two methods.

This paper describes a general methodological framework for evaluating the perceptual properties of auditory stimuli. The framework provides analysis techniques that can ensure the effective use of sound for a variety of applications including virtual reality and data sonification systems. Specifically, we discuss data collection techniques for the perceptual qualities of single auditory stimuli including identification tasks, context-based ratings, and attribute ratings. In addition, we present methods for comparing auditory stimuli, such as discrimination tasks, similarity ratings, and sorting tasks. Finally, we discuss statistical techniques that focus on the perceptual relations among stimuli, such as Multidimensional Scaling (MDS) and Pathfinder Analysis. These methods are presented as a starting point for an organized and systematic approach for non-experts in perceptual experimental methods, rather than as a complete manual for performing the statistical techniques and data collection methods. It is our hope that this paper will help foster further interdisciplinary collaboration among perceptual researchers, designers, engineers, and others in the development of effective auditory displays.

Probabilistic uncertainty is a phenomenon that occurs to a certain degree in many engineering!~ applications. The effects that the uncertainty has upon a given system response is a matter of some concern. Techniques which provide insight to these effects will be required as modeling and prediction become a more vital tool in the engineering design process. As might be expected, this is a difficult proposition and the focus of many research efforts. The purpose of this paper is to outline a procedure to evaluate uncertainty in dynamic system response exploiting Gauss-Hermite numerical quadrature. Specifically numerical integration techniques are utilized in conjunction with the Advanced Mean Value method to efficiently and accurately estimate moments of the response process. A numerical example illustrating the use of this analytical tool in a practical framework is presented.

Copper powder was sprayed by the cold-gas dynamic method. In-flight particle velocities were measured with a laser-two-focus system as a function of process parameters such as gas temperature, gas pressure, and powder feed rate. Particle velocities were uniform in a relatively large volume within the plume and agreed with theoretical predictions. The presence of the substrate was found to have no significant effect on particle velocities. Cold-spray deposition efficiencies were measured on aluminum substrates as a function of particle velocity and incident angle of the plume. Deposition efficiencies of up to 95% were achieved. The critical velocity for deposition was determined to be about 640 meters per second. This work investigates both the in-flight characteristics of copper particles in a supersonic cold-spray plume and the build-up of the subsequent coating on aluminum substrates. Velocities were found to be relatively constant within a large volume of the plume. Particle counts dropped off sharply away from the central axis. The presence of a substrate was found to have no effect on the velocity of the particles. A substantial mass-loading effect on the particle velocity was observed; particle velocities begin to drop as the mass ratio of powder to gas flow rates exceeds 3%. The measured variation of velocity with gas pressure and pre-heat temperature was in fairly good agreement with theoretical predictions. Helium may be used as the driving gas instead of air in order to achieve higher particle velocities for a given temperature and pressure. Coating deposition efficiencies were found to increase with particle velocity and decrease with gun- substrate angle. There did not appear to be any dependence of the deposition efficiency on coating thickness. A critical velocity for deposition of about 640 mk appears to fit the data well. The cold-spray technique shows promise as a method for the deposition of materials which are thermally sensitive or may experience rapid oxidation under typical thermal spray conditions. High deposition efficiencies are achievable for certain coating-substrate conditions. Work remains to determine the material and microstructural properties which govern the coating process.

The etch rate of GaN under W-assisted photoelectrochemical conditions in KOH solutions is found to be a strong function of illumination intensity, solution molarity, sample bias and material doping level. At low e-h pair generation rates, grain boundaries are selectively etched, while at higher illumination intensities etch rates for unintentionally doped (n - 3x 10^12Gcm-3) GaN are 2 1000 .min-l. The etching is diffusion limited under our conditions with an activation energy of - 0.8kCal.mol-1. The etched surfaces are rough, but retain their stoichiometry. PEC etching is found to selectively reveal grain boundaries in GaN under low light illumination conditions. At high lamp powers the rates increase with sample temperature and the application of bias to the PEC cell, while they go through a maximum with KOH solution molarity. The etching is diffusion-limited, producing rough surface morphologies that are suitable in a limited number of device fabrication steps. The surfaces however appear to remain relatively close to their stoichiometric composition.

Particle-in-cell simulations of applied-B ion diodes using the QUICKSILVER code have been augmented with Monte Carlo calculations of electron-anode interactions (reflection and energy deposition). Extraction diode simulations demonstrate a link between the instability evolution and increased electron loss and anode heating. Simulations of radial and extraction ion diodes show spatial non-uniformity in the predicted electron loss profile leading to hot spots on the anode that rapidly exceed the 350-450 {degree}C range, known to be sufficient for plasma formation on electron-bombarded surfaces. Thermal resorption calculations indicate complete resorption of contaminants with 15-20 kcal/mole binding energies in high-dose regions of the anode during the power pulse. Comparisons of parasitic ion emission simulations and experiment show agreement in some aspects; but also highlight the need for better ion source, plasma, and neutral gas models.

Amorphous carbon films have been grown by evaporation of graphite with concurrent Ar+ ions bombardment assistance. The ion energy has been varied between 0-800 V while keeping a constant ion to carbon atom arrival ratio. Film composition and density were determined by ion scattering techniques (RBS and ERDA), indicating a negligible hydrogen content and a density dependence with the assistance voltage. The bonding structure of the films has been studied by Raman and X-ray Absorption Near-Edge (XANES) spectroscopy. Different qualitative effects have been found depending on the ion energy range. For ion energies below 300 eV, there is a densification of the carbon layer due to the increase in the sp3 content. For ion energies above 300 eV sputtering phenomena dominate over densification, and thinner films are found with increasing assistance voltage until no film is grown over 600 V. The films with the highest SP3 content are grown with intermediate energies between 200-300 V.

A method is presented for connecting dissimilar finite element meshes in three dimensions. The method combines the concept of master and slave surfaces with the uniform strain approach for surface, corrections finite elements- By modifyhg the are made to element formulations boundaries of elements on the slave such that first-order patch tests are passed. The method can be used to connect meshes which use different element types. In addition, master and slave surfaces can be designated independently of relative mesh resolutions. Example problems in three-dimensional linear elasticity are presented.

Many lessons have been learned over the past 24 years as the Waste Isolation Pilot Plant (WIPP) project has progressed from initial site characterization to final licensing that may be of relevance to other nuclear-waste-disposal projects. These lessons pertain to the manner in which field and laboratory investigations are planned, how experiments are interpreted, how conceptual and numerical models are developed and simplified~ and how defensibility and credibility are achieved and maintained. These lessons include 1) Site characterization and performance assessment (PA) should evolve together through an iterative process, with neither activity completely dominating the other. 2) Defensibility and credibility require a much greater depth of understanding than can be represented in PA models. 3) Experimentalists should be directly involved in model and parameter abstraction and simplification for PA. 4) External expert review should be incorporated at all stages of a project~ not just after an experiment or modeling activity is completed. 5) Key individuals should be retained for the life of a project or a process must be established to transfer their working knowledge to new individuals. 6) An effective QA program needs to be stable and consistent for the duration of a project and rests on best scientific practices. All of these lessons relate to the key point that consideration must be given from the earliest planning stages to maximizing the defensibility and credibility of all work.

Most analytical solutions and computer codes for well-test analysis assume a radial flow geometry around a well even though actual flow geometries can be quite different particularly in fractured media. Accurate estimation of hydraulic parameters requires knowledge of the flow geometry. Flow dimensions, representing the combined effects of flow geometry and variations in hydraulic properties, em be interpreted from the late-time slope of the pressure derivative on a log-log plot. However, the interpreted flow dimensions could be caused by an infinite number of flow geometry and hydraulic property combinations. Identifying the correct flow geometry so that appropriate hydraulic properties can be calculated is a difficult process, requiring additional information from a variety of sources. Defining a "conservative" model for a system with nonradial flow dimensions is problematic at best. Errors are compounded when hydraulic properties interpreted by force-fitting radial model to tests in nonradial systems are used in flow and transport models that also fail to take proper account of flow geometry. Whatever the flow dimension of a system might be, proper test interpretation and careful model construction, calibration, and testing are required to provide accurate modeling of flow and transport in that system.

A principal goal of the shock physics program at Sandia is to establish a capability to make accurate equation of state (EOS) measurements on the Z pulsed radiation source. The Z accelerator is a source of intense x-ray radiation, which can be used to drive ablative shocks for EOS studies. With this source, ablative multi shocks can be produced to study materials over the range of interest to both weapons and ICF physics programs. In developing the capability to diagnose these types of studies on Z, techniques commonly used in conventional impact generated experimental were implemented. The primary diagnostic presently being used for this work is velocity interferometry, VISAR, which not only provides Hugoniot particle velocity measurements, but also measurements of non-shock EOS measurements, such as isentropic compression. In addition to VISAR capability, methods for measuring shock velocity have also been developed for shock studies on Z. When used in conjunction with the Rankine- Hugoniot jump conditions, material response at high temperatures and pressures can be inferred. Radiation in the Z accelerator is produced when approximately 18 MA are passed through a cylindrical wire array typically 20 to 50 mm in diameter and 10 to 20 mm in height. 200-300 wires with initial diameters on the order of 8 to 20 micron form, upon application of the current, a plasma shell, which is magnetically imploded until it collapses and stagnates on axis, forming a dense plasma emitter in the shape of a column, referred to as a" z pinch". The initial wire array and subsequent plasma pinch are confined within a metallic can, referred to as a primary hohlraum, which serves as both a current return path and a reflective surface to contain the radiation. Attached to openings in the primary hohlraum wall are smaller tubes referred to as secondaries. Multiple secondaries can be fielded on most experiments, which are the typical location for mounting EOS samples. In this configuration, the secondary S1 contains two separate VISAR probes for making velocity measurements at different material thicknesses. By correlating the resulting velocity profiles in time, a measurement of shock velocity can be determined. In addition, the velocity profiles provide the Hugoniot particle velocity after the records were impedance-matched. Secondaries S2 and S3 provide measurements of shock velocity using laser light reflected from steps. As the shock arrives at each of these surfaces, the surface reflectivity significantly decreases, which causes a sharp drop in return light. The shock velocity can be inferred from shock arrival at different steps The z-pinch technique is particularly useful for producing high amplitude shock waves for EOS applications. An alternative approach for using Z is to produce shockless loading directly with the magnetic pressure in the accelerator.

The electronic defect density of native, anodic, and synthetic Al oxide layers on Al were studied by solid state electrical measurement as a function of hydration OF the oxide. The non-hydrated synthetic Al oxide layers, which included electron cyclotron resonance (ECR) plasma deposited oxides as well as ECR plasma grown oxides, were highly insulating with electrical transport dominated by thermal emission from deep traps within the oxide. Following hydration these oxides and the native oxides exhibited a large increase in electronic defect density as evidenced by increases in the DC leakage current, reduction in the breakdown field, and increase in AC conductance. Elastic recoil detection of hydrogen revealed that hydration leads to hydrogen incorporation in the oxide films and hydrogen injection through the films into the Al layer below. The increase in electronic defect concentration is related to this hydrogenation and may play a significant role in localized corrosion initiation.

BioSimMER (Bioterrorism Simulated Medical Emergency Response) is a Virtual Reality-based mission rehearsal and training environment. BioSimMER employs contingency-oriented, multiple-path algorithms and MOESINIOPS focused on real-world operations. BioSimMER is network-based and immerses multiple trainees in a high resolution synthetic environment, including virtual casualties and instruments that they may interact with and manipulate. Trainees are represented as individuals by virtual human Avatars. The simulation consists of several components: virtual casualties dynamically manifest the symptoms of their injuries and respond to the intervention of the trainees. Agent transport analysis is used to simulate casualty exposures and to drive the responses of simulated sensors/detectors. The selected prototype scenario is representative of combined injuries anticipated in BW operations.

Recent beam bending (BB) experiments of microporous t31rns with very small pores have shown that the fluid confined in these pores exhibits monotonic compressive stresses as the relative pressure is varied from vacuum to saturation (relative vapor pressure, p/p. = 1). The variation of the stress near saturation is found to be linear in hz(p) and given by the saturated liquid density to within 20%. Capillary condensed fluids are traditionally described by the Laplace-Kelvin (LK) theory. LK theory correctly predicts the slope of the stress near saturation to be pl, but also predicts that the stress should be zero at saturation and tensile between saturation aud the capillary transition pressure. Hence LK theory does not capture the monotonic compressive stress observed in BB experiments. This report describes the results of density functional theory calculations for a simple fluid continued to a slit pore network. We show how the presence of even a small amount of polydispersity in pore size leads to both a monotonic compressive stress as well as the observed LK slope.

Many types of self-assembly can be found in nature. They include crystallization, the formation of micelles, and the folding of proteins. Recently there has been much interest in pursuing nano-to-microscopically engineered materials by way of self-assembly on imprinted or templated surfaces. In all of these diverse cases, wetting plays a critical role in the assembly process. Wetting involves the interactions of the substrate or amphiphilic molecule or macromolecule with a solvent. In many self-assembled systems we find that the critical feature of the system is a substrate! or macromolecule with a both hydrophilic and hydrophobic nature. In this paper we discuss the wetting properties of a striped surface where the stripes represent alternating chemical characteristics. We show how the chemical heterogeneity affects the wetting properties of the surface (e.g. the static contact angle), and discuss the length limitations on the soft lithography approach. In this paper, the wetting of a chemically heterogeneous surface is studied using a nonlocal Density Functional Theory (DFT). The results for the heterogeneous surface model we discuss have immediate implications for soft-lithography by self-assembly. It also lends fundamental insight into the mechanisms controlling self-assembly of macromolecules. We present the results of nonlocal 2D DFT calculations on the wetting properties of chemically heterogeneous surfaces. These calculations showed complex density distributions and phase behavior as a result of the heterogeneity. The location of the wetting transition are found to be strongly dependent on the extent and strength of the heterogeneity, and complete wetting was suppressed altogether if the hydrophobic parts of the surface were large enough. In these cases, the condensed nanophase may crystallize if the hydrophilic surface-fluid interactions are strong enough. By exploring the phase space including strength of hydrophilic interactions and extent of chemical heterogeneity, an operational phase diagram was established that could be used for designing nanoscopically tailored devices and materials.

Nanometer-scale compositional structure in InAsxP1.InNYAsxPl.x-Y/InP, grown by gas-source molecular-beam epitaxy and in InAsl-xPJkAsl$b#InAs heterostructures heterostructures grown by metal-organic chemical vapor deposition has been characterized using cross-sectional scanning tunneling microscopy. InAsxP1-x alloy layers are found to contain As-rich and P-rich clusters with boundaries formed preferentially within (T 11) and (111) crystal planes. Similar compositional structure is observed within InNYAsxP1-x-Y alloy layers. Imaging of InAsl-xp@Asl#bY superlattices reveals nanometer-scale clustering within both the hAsI-.p and InAsl$bY alloy layers, with preferential alignment of compositional features in the direction. Instances are observed of compositional structure correlated across a heterojunction interface, with regions whose composition corresponds to a smaller unstrained lattice, constant relative to the surrounding alloy material appearing to propagate across the interface.

Piezoelectric effects on the optical properties of GaN/AlGaN multiple quantum wells (MQWS) have been investigated by picosecond time-resolved photoluminescence (PL) measurements. For MQWS with well thickness 30 and 40 the excitonic transition peak positions at 10 K in continuous wave (CW) spectra are red-shifted with respect to the GaN epilayer by 17 meV and 57 meV, respectively. The time-resolved PL spectra of the 30 and 40 well MQWS reveal that the excitonic transition is in fact blue-shifted at early delay times due to quantum confinement of carriers. The spectral peak position shifts toward lower energies as the delay time increases and becomes red-shifted at longer delay times. We have demonstrated that the results described above is due to the presence of the piezoelectric field in the GaN wells of GaN/AlGaN MQWS subject to elastic strain together with screening of the photoexcited carriers. By comparing experimental and calculation results, we conclude that the piezoelectric field strength in GaN/Al.15G~.85N MQWS has a lower limit value of about 560 kV/cm: The electron and hole wave function distributions have also been obtained. The implication of our findings on the practical applications of GaN based optoelectronic devices is also discussed.

Epitaxial growth of AlAs-InAs short-period superlattices on (001) InP can lead to heterostructures exhibiting strong, quasi-periodic, lateral modulation of the alloy composition; transverse satellites arise in reciprocal space as a signature of the compositional modulation. Using an x-ray diffractometer equipped with a position-sensitive x-ray detector, we demonstrate reciprocal-space mapping of these satellites as an efficient, nondestructive means for detecting and characterizing the occurrence of compositional modulation. Systematic variations in the compositional modulation due to the structural design and the growth conditions of the short-period superlattice are characterized by routine mapping of the lateral satellites. Spontaneous compositional modulation occurs along the growth front during molecular-beam epitaxy of (AlAs) (InAs)n short-period superlattices. The modulation is quasi-periodic and forms a lateral superlattice superimposed on the intended SPS structure. Corresponding transverse satellites arise about each reciprocal lattice point, and x-ray diffraction can be routinely used to map their local reciprocal-space structure. The integrated intensity, spacing, orientation, and shape of these satellites provide a reliable means for nondestructively detecting and characterizing the compositional modulation in short-period superlattices. The analytical efficiency afforded by the use of a PSD has enabled detailed study of systematic vacations in compositional modulation as a function of the average composition, the period, and the growth rate of the short- period superlattice

A variety of different plasma chemistries, including SF6, Cl2, IC1 and IBr, have been examined for dry etching of 6H-SiC in high ion density plasma tools (Inductively Coupled Plasma and Electron Cyclotron Resonance). Rates up to 4,500~"min-1 were obtained for SF6 plasmas, while much lower rates (S800~.min-') were achieved with Cl2, ICl and IBr. The F2- based chemistries have poor selectivity for SiC over photoresist masks (typically 0.4-0.5), but Ni masks are more robust, and allow etch depths 210pm in the SiC. A micromachining process (sequential etch/deposition (<2,000Angstrom min-1) for SiC steps) designed for Si produces relatively low etch rates.

A systematic study of the etch characteristics of GaN, AlN and InN has been performed with boron halides- (BI{sub 3} and BBr{sub 3}) and interhalogen- (ICl and IBr) based Inductively Coupled Plasmas. Maximum etch selectivities of -100:1 were achieved for InN over both GaN and AlN in the BI{sub 3} mixtures due to the relatively high volatility of the InN etch products and the lower bond strength of InN. Maximum selectivies of- 14 for InN over GaN and >25 for InN over AlN were obtained with ICl and IBr chemistries. The etched surface morphologies of GaN in these four mixtures are similar or better than those of the control sample.

Free-standing aligned carbon nanotubes have previously been grown above 7000C on mesoporous silica embedded with iron nanoparticles. Here, carbon nanotubes aligned over areas up to several square centimeters were grown on nickel-coated glass below 666oC by plasma-enhanced hot filament chemical vapor deposition. Acetylene (C2H2) gas was used as the carbon source and ammonia (NH3) gas was used as a catalyst and dilution gas. Nanotubes with controllable diameters from 20 to 400 nanometers and lengths from 0.1 to 50 micrometers were obtained. Using this method, large panels of aligned carbon nanotubes can be made under conditions that are suitable for device fabrication.

In a collaborative program between the United States Nuclear Regulatory Commission (USNRC) and the Nuclear Power Engineering Corporation (NUPEC) of Japan under sponsorship of the Ministry of International Trade and Ihdustry, the seismic behavior of Prestressed Concrete Containment Vessels (PCCV) is being investigated. A 1:10 scale PCCV model has been constructed by NUPEC and subjected to seismic simulation tests using the high performance shaking table at the Tadotsu Engineering Laboratory. A primary objective of the testing program is to demonstrate the capability of the PCCV to withstand design basis earthquakes with a significant safety margin against major damage or failure. As part of the collaborative program, Sandia National Laboratories (SNL) is conducting research in state-of-the-art analytical methods for predicting the seismic behavior of PCCV structures, with the eventual goal of understanding, validating, and improving calculations dated to containment structure performance under design and severe seismic events. With the increased emphasis on risk-informed- regulatory focus, more accurate ch&@erization (less uncertainty) of containment structural and functional integri~ is desirable. This paper presents results of post-test calculations conducted at ANATECH to simulate the design level scale model tests.

This report addresses various facts and myths concerning the Y2K (Year 2000) problem.

Surviving in a data-rich environment means understanding the difference between data and information. This paper reviews an environmental case study that illustrates that understanding and shows its importance. In this study, a decision problem was stated in terms of au economic-objective fimction. The function contains a term that defines the stochastic relationship between the decision and the information obtained during field chamctetition for an environmental contaminant. Data is defied as samples drawn or experimental realizations of a mudom fimction. Information is defined as the quantitative change in the value of the objective fiction as a result of the sample.

Wind energy researchers at Sandia National Laboratories have developed a small, lightweight, time- synchronized, robust data acquisition system to acquire long-term time-series data on a wind turbine rotor. A commercial data acquisition module is utilized to acquire data simultaneously from multip!e strain-gauge, analog, and digital channels. Acquisition of rotor data at precisely the same times as acquisition of ground data is ensured by slaving the acquisition clocks on the rotor- based data unit and ground-based units to the Global Positioning Satellite (GPS) system with commercial GPS receiver units and custom-built and programmed programmable logic devices. The acquisition clocks will remain synchronized within two microseconds indefinitely. Field tests have confirmed that synchronization can be maintained at rotation rates in excess of 350 rpm, Commercial spread-spectrum radio modems are used to transfer the rotor data to a ground- based computer concurrently with data acquisition, permitting continuous acquisition of data over a period of several hours, days or even weeks.

Abstract not provided.

Rapid detection of excursions in the concentration of organic contaminants in water that is being recycled is crucial to the more widespread acceptance of rinse water recycling as a method of reducing water usage in semiconductor manufacturing. In 1995 SEMATECH'SS116 PTAB (Project Technical Advisory Board) arbitrarily targeted a response time of 30s as the goal for the on-line detection of TOC (Total Oxidizable Carbon) in water - a goal thought to simpliilj the design of water recycling systems (less volume required for water storage in the recycle loop) and lead to more widespread adoption of recycling of spent rinse waters by the US semiconductor industry. A subsequent evaluation of the TOC analyzers commercially available in early 1996 demonstrated that the fastest response times were on the order of three minutes ljllef. 1]. This paper updates the 1996 evaluation of commercially available TOC analyzers by assessing modified versions of two of the previously evaluated analyzers and also anew analyzer that became commercially available in 1997.

Esperanzaite, ideally NaCazA12(As5+0.i)[As5+03 (OH)] (OH)2FJH20), Z =2, is a new mineral from the Mina h Esperarq Durango State, Mexico. The mineral occurs as blue-green botryoidal crystalline masses on rhyolite, with separate spheres up to 1.5 mm Y Deceased in diameter. Mobs hardness is 4.5, specific gravity 3.240h, and 3.36( 3)C.IC. Optical properties were measured in 589 nm light. Esperanzaite is biaxial (-), .Y= Y = Z= colorless, a 1.580(1), ~ 1.588( 1), and y 1.593(1 ); 2V0hs is 74(1 ~ and 2 }'CUIC is 76.3". Dispersion is medium, r < v, and optic axes are oriented as a A Z = +50.5o, b = Y, c P. X = +35". The five strongest X-ray diffraction maxima in the powder pattern are (~ /, hk~: 2.966,100, 13 i, 31 i, 031 ; 3.527,90, 220; 2.700,90,221,002, 040; 5.364>80, 001, 020; 4.796,80,011. Esperanzaite is monoclinic, u 9.687(5), b 10.7379(6), c 5.5523(7)& ~ 105.32( 1 )", space group P21/nz. The atomic arrangement of esperanzaite was solved by Direct Methods and Fourier analysis (R= 0.03 1). The Fundamental Building Block is formed of stacks of heteropolyhedral tetramers; the tetramers are formed of two arsenate tetrahedral and two Al octahedra, comer-linked in 4-member rings. The Fundamental Building Blocks are linked by irregular lda~j and Ca@ polyhedra.

The role of extended and point defects, and key impurities such as C, O and H, on the electrical and optical properties of GaN is reviewed. Recent progress in the development of high reliability contacts, thermal processing, dry and wet etching techniques, implantation doping and isolation and gate insulator technology is detailed. Finally, the performance of GaN-based electronic and photonic devices such as field effect transistors, UV detectors, laser diodes and light-emitting diodes is covered, along with the influence of process-induced or grown-in defects and impurities on the device physics.

Enhancement of the Zeeman energy of 2D conduction electrons near v = 1 by optical dynamic nuclear polarization (lINP), as observed by the Overhauser shift of the transport detected electron spin resonance, is measured quantitatively for the first time in GaAs/AIGaAs mukiquantum wells. The NMR signal enhancement is obtained under similar conditions in the same sample, allowing the hyperke coupling constant of 3.7T between between the nuclei and 2D conduction electrons to be measured for the first time. The potential to suppress the Zeeman energy by optical DNP is discussed in the context of its potential influence on Skyrmion formation.

The U.S. and Russian weapons dismantlement process is producing hundreds of tons of excess plutonium (Pu) and highly enriched uranium (HEU) fissile materials. The nuclear operations associated with the final disposition of these materials will be occurring in both countries for decades. A significant accident during these operations could delay the disposition process. Russia- U.S. collaborative efforts to address safety issues associated with disposition processes have been ongoing since 1993. The experience of these collaborative efforts have demonstrated the need for a systematic and formalized approach to identifjring and prioritizing collaborative projects. A systematic approach to the successfid implementation of a formal program will require the definition of year by year program objectives, specific technical program areas, a process for the prioritization and selection of projects, and identification of performance measures to evaluate the success of projects. Specialized working groups established for each technical area are needed to define research priorities, review research proposals, and recommend proposals for tiding. A systematic approach to the establishment of a formal U.S.-Russia cooperative program will serve to ensure the safety and continuity of disposition processes and reduce the nuclear proliferation risks presented by this material. The U.S. and Russian weapons dismantlement process is producing hundreds of tons of excess plutonium (Pu) and highly enriched uranium (HEU) fissile materials. The U.S. and Russia are both converting and blending HEU into low enriched uranium (LEU) for use in existing reactors. Russia also plans to fiel reactors with excess Pu. The U.S. is on a two-path approach for the disposition of excess Pu: (1) use of Pu in existing reactors and/or (2) immobilization of the Pu in glass or ceramics followed by geologic disposal. The fissile nuclear materials storage, handling, processing, and transportation processes associated with the disposition process will be occurring in both countries for decades. A significant accident at any point in the process could significantly delay the disposition process. Russia-U.S. collaborative efforts to address safety issues associated with nuclear processes required for the disposition of excess weapons grade nuclear materials were initiated in response to the 1993 Tomsk-7 accident. A joint Russia-U.S. team evaluated the causes of an explosion in a nuclear fuel reprocessing tank at the Tomsk-7.

For many years, Sandia National Laboratories has been involved in the development and application of rapid prototyping and dmect fabrication technologies to build prototype parts and patterns for investment casting. Sandia is currently developing a process called Laser Engineered Net Shaping (LENS~) to fabricate filly dense metal parts dwectly from computer-aided design (CAD) solid models. The process is similar to traditional laser-initiated rapid prototyping technologies such as stereolithography and selective laser sintering in that layer additive techniques are used to fabricate physical parts directly from CAD data. By using the coordinated delivery of metal particles into a focused laser beam apart is generated. The laser beam creates a molten pool of metal on a substrate into which powder is injected. Concurrently, the substrate on which the deposition is occurring is moved under the beam/powder interaction zone to fabricate the desired cross-sectiwal geometry. Consecutive layers are additively deposited, thereby producing a three-dmensional part. This process exhibits enormous potential to revolutionize the way in which metal parts, such as complex prototypes, tooling, and small-lot production parts, are produced. The result is a comple~ filly dense, near-net-shape part. Parts have been fabricated from 316 stainless steel, nickel-based alloys, H13 tool steel, and titanium. This talk will provide a general overview of the LENS~ process, discuss potential applications, and display as-processed examples of parts.

In direct laser metal deposition technologies, such as the Laser (LENS) process, it is important to understand and control the Engineered Net Shaping thermal behavior during fabrication. With this control, components can be reliably fabricated with desired structural material properties. This talk will describe the use of contact and imaging techniques to monitor the thermal signature during LENS processing. Recent results show a direct correlation between thermal history and material properties, where the residual stress magnitude decreases as the laser power, and therefore thermal signature, increases. Development of an understanding of solidification behavior, residual stress, and microstructural evolution with respect to thermal behavior will be discussed.

Current and future generations of sophisticated compound semiconductor devices require the ability for submicron scale patterning. The situation is being complicated since some of the new devices are based on a wider diversity of materials to be etched. Conventional IUE (Reactive Ion Etching) has been prevalent across the industry so far, but has limitations for materials with high bond strengths or multiple elements. IrI this paper, we suggest high density plasmas such as ECR (Electron Cyclotron Resonance) and ICP (Inductively Coupled Plasma), for the etching of ternary compound semiconductors (InGaP, AIInP, AlGaP) which are employed for electronic devices like heterojunction bipolar transistors (HBTs) or high electron mobility transistors (HEMTs), and photonic devices such as light-emitting diodes (LEDs) and lasers. High density plasma sources, opeiating at lower pressure, are expected to meet target goals determined in terms of etch rate, surface morphology, surface stoichiometry, selectivity, etc. The etching mechanisms, which are described in this paper, can also be applied to other III-V (GaAs-based, InP-based) as well as III-Nitride since the InGaAIP system shares many of the same properties.

Inductively coupled plasma (ICP) etching characteristics of GaSb and AIGaAsSb have been investigated in BC13/Ar and Clz/Ar plasmas. The etch rates and selectivity between GaSb and AIGaAsSb are reported as functions of plasma chemistry, ICP power, RF self-bias, and chamber pressure. It is found that physical sputtering resorption of the etch products plays a dominant role in BC13/Ar ICP etching, while in Clz/Ar plasma, the chemical reaction dominates the etching. GaSb etch rates exceeding 2 ~rnhnin are achieved in Clz/Ar plasmas with smooth surfaces and anisotropic profiles. In BC13/Ar plasmas, etch rates of 5100 Mmin and 4200 Mmin are obtained for GaSb and AIGaAsSb, respectively. The surfaces of both GaSb and AIGaAsSb etched in BC13/Ar plasmas remain smooth and stoichiometric over the entire range of plasma conditions investigated. This result is attributed to effective removal of etch products by physical sputtering. For a wide range of plasma conditions, the selectivity between GaSb and AIGaAsSb is close to unity, which is desirable for fabricating etched mirrors and gratings for Sb-based mid-IR laser diodes.

This paper presents an analysis of a decentralized coordination strategy for organizing and controlling a team of mobile robots performing collective search. The alpha-beta coordination strategy is a family of collective search algorithms that allow teams of communicating robots to implicitly coordinate their search activities through a division of labor based on self-selected roIes. In an alpha-beta team. alpha agents are motivated to improve their status by exploring new regions of the search space. Beta a~ents are conservative, and reiy on the alpha agents to provide advanced information on favorable regions of the search space. An agent selects its current role dynamically based on its current status value relative to the current status values of the other team members. Status is determined by some function of the agent's sensor readings, and is generally a measurement of source intensity at the agent's current location. Variations on the decision rules determining alpha and beta behavior produce different versions of the algorithm that lead to different global properties. The alpha-beta strategy is based on a simple finite-state machine that implements a form of Variable Structure Control (VSC). The VSC system changes the dynamics of the collective system by abruptly switching at defined states to alternative control laws . In VSC, Lyapunov's direct method is often used to design control surfaces which guide the system to a given goal. We introduce the alpha-beta aIgorithm and present an analysis of the equilibrium point and the global stability of the alpha-beta algorithm based on Lyapunov's method.

Liquid flow cells have been fabricated to prepare an array of QCMS operating simultaneously for detection and identification of VOCS in water. TWO signals, a tlequency response and a damping voltage response, were obtained per resonator. A blank QCM was used as a reference to account for changes in liquid density and viscosity. Nine different polymer coatings applied using a spin coat technique have been examined for VOC response under liquid flow conditions. A matrix of three classes of VOCS were examined for each coating with four chemicals in each class. The three classes of VOCS are polar, nonpolar and chlorinated. A pattern recognition technique, called visually empirical region of influence (VERI), was used to cluster the responses in n-dimensional space. Chemicals within a class varying by only one methyl group (e.g., toluene and xylene) are easily discriminated using only two different coatings with three different QCM responses. All chemicak were easily separated and detected with a total of 5 films and 6 responses with >99% accuracy.

When dealing with measured data from dynamic systems we often make the tacit assumption that the data are generated by linear dynamics. While some systematic tests for linearity and determinism are available - for example the coherence fimction, the probability density fimction, and the bispectrum - fi,u-ther tests that quanti$ the existence and the degree of nonlinearity are clearly needed. In this paper we demonstrate a statistical test for the nonlinearity exhibited by a dynamic system excited by Gaussian random noise. We perform the usual division of the input and response time series data into blocks as required by the Welch method of spectrum estimation and search for significant relationships between a given input fkequency and response at harmonics of the selected input frequency. We argue that systematic tests based on the recently developed statistical method of surrogate data readily detect significant nonlinear relationships. The paper elucidates the method of surrogate data. Typical results are illustrated for a linear single degree-of-freedom system and for a system with polynomial stiffness nonlinearity.

Advances in fast, pulsed-power technologies have resulted in the development of very high current drivers that have current rise times - 100 ns. The largest such pulsed power drive r today is the new Z accelerator located at Sandia National Laboratories in Albuquerque, New Mexico. Z is capable of delivering more than 20 MA with a time-to-peak of 105 ns to low inductance (- 1 nH)loads. Such large drivers are capable of directly generating magnetic fields approaching 3 kT in small, 1 -cm3, volumes. In addition to direct field generation, Z can be used to compress an applied, axial seed field with a plasma. Flux compression scheme~: are not new and are, in fact, the basis of all explosive flux-compression generators but we propose the use of plasma armatures rather than solid, conducting armatures. We will present experimental results from the Z accelerator in which magnetic fields - 2 kT are generated and measured with several diagnostics. Issues such as energy loss in solid conductors and dynamic response of current-carrying conductors to very large magnetic fields will be reviewed in context with Z experiments. We will describe planned flux-compression experiments that are expected to create the highest-magnitude uniform-field volumes yet attained in the laboratory.

Straightforward algebraic expressions describing the elastic wavefield produced by a line source of finite length are derived in circular cylindrical coordinates. The surrounding elastic medium is assumed to be both homogeneous and isotropic, anc[ the source stress distribution is considered axisymmetic. The time- and space-domain formulae are accurate at all distances and directions from the source; no fa-field or long-wavelength assumptions are adopted for the derivation. The mathematics yield a unified treatment of three different types of sources: an axial torque, an axial force, and a radial pressure. The torque source radiates only azirnuthally polarized shear waves, whereas force and pressure sources generate simultaneous compressional and shear radiation polarized in planes containing the line source. The formulae reduce to more familiar expressions in the two limiting cases where the length of the line source approaches zero and infinity. Far-field approximations to the exact equations indicate that waves radiated parallel to the line source axI.s are attenuated relative to those radiated normal to the axis. The attenuation is more severe for higher I?equencies and for lower wavespeeds. Hence, shear waves are affected more than compressional waves. This fi-equency- and directiondependent attenuation is characterized by an extremely simple mathematical formula, and is readily apparent in example synthetic seismograms.

Exponential-13,6 (EXP-13,6) potential pammeters for 750 gases composed of 48 elements were determined and assembled in a database, referred to as the JCZS database, for use with the Jacobs Cowperthwaite Zwisler equation of state (JCZ3-EOS)~l) The EXP- 13,6 force constants were obtained by using literature values of Lennard-Jones (LJ) potential functions, by using corresponding states (CS) theory, by matching pure liquid shock Hugoniot data, and by using molecular volume to determine the approach radii with the well depth estimated from high-pressure isen- tropes. The JCZS database was used to accurately predict detonation velocity, pressure, and temperature for 50 dif- 3 Accurate predictions were also ferent explosives with initial densities ranging from 0.25 glcm3 to 1.97 g/cm . obtained for pure liquid shock Hugoniots, static properties of nitrogen, and gas detonations at high initial pressures.

Foam evokes many different images: waves breaking at the seashore, the head on a pint of Guinness, an elegant dessert, shaving, the comfortable cushion on which you may be seated... From the mundane to the high tech, foams, emulsions, and cellular solids encompass a broad range of materials and applications. Soap suds, mayonnaise, and foamed polymers provide practical motivation and only hint at the variety of materials at issue. Typical of mukiphase materiaIs, the rheoIogy or mechanical behavior of foams is more complicated than that of the constituent phases alone, which may be gas, liquid, or solid. For example, a soap froth exhibits a static shear modulus-a hallmark of an elastic solid-even though it is composed primarily of two Newtonian fluids (water and air), which have no shear modulus. This apparent paradox is easily resolved. Soap froth contains a small amount of surfactant that stabilizes the delicate network of thin liq- uid films against rupture. The soap-film network deforms in response to a macroscopic strain; this increases interracial area and the corresponding sur- face energy, and provides the strain energy of classical elasticity theory [1]. This physical mechanism is easily imagined but very challenging to quantify for a realistic three-dimensional soap froth in view of its complex geome- try. Foam micromechanics addresses the connection between constituent properties, cell-level structure, and macroscopic mechanical behavior. This article is a survey of micromechanics applied to gas-liquid foams, liquid-liquid emulsions, and cellular solids. We will focus on static response where the foam deformation is very slow and rate-dependent phenomena such as viscous flow can be neglected. This includes nonlinear elasticity when deformations are large but reversible. We will also discuss elastic- plastic behavior, which involves yield phenomena. Foam structures based on polyhedra packed to fill space provide a unify- ing geometrical theme. Because a two-dimensional situation is always easier to visualize and usually easier to analyze, the roots of foam micromechanics lie in the plane packed with polygons. There are striking similarities as well as obvious differences between 2D and 3D.

Security technologies are not the answer to all school security problems. However, they can be an excellent tool for school administrators and security personnel when incorporated into a total security strategy involving personnel, procedures, and facility layout. Unfortunately, very few of the tougher security problems in schools have solutions that are affordable, effective, and acceptable. Like any other type of facility, a school's security staff must understand the strengths and limitations of the security measures they are c

This paper explores two potential applications of Virtual Reality (VR) to international nuclear safeguards: training and information organization and navigation. The applications are represented by two existing prototype systems, one for training nuclear weapons dismantlement and one utilizing a VR model to facilitate intuitive access to related sets of information.

The paper presents an investigation of the impacts of deregulation on the reliability, in terms of capacity adequacy, of a large multi-arm power pool. The study was conducted using a vwsirm of a Monte Carlo simulation-based bulk power system rdiability model called NA.RI'. The study examined expected ohanges in opmating policies and other changes expected under deregulation and Gorwludes that reliabtity is Uke\ y to be signific~tly degraded at least until the transmission network can be strengthen.

Self-aligned GaAs JFET narrowband amplifiers operating at 2.4 GHz were designed and fabricated with both discrete WETS as a hybrid amplifier and as RFICS. Enhancement-mode JFETs were used in order to be compatible with complementary digital logic. Hybrid amplifiers achieved 8-10 dB of gain at 2.4 GHz and 1 mW DC bias level. The RFIC achieved 10 dB of gain at 24 GHz and 2 mW DC bias level.

We report in this paper a study of the effective mass in thin oxide Si-MOSFETs, using the temperature dependence of the Shubnikov-de Haas (SdH) effect and following the methodology developed by Smith and Stiles.

Plasma, vapor and debris associated with an impact or explosive event have been demonstrated in the laboratory to produce radiofrequency and optical electromagnetic emissions that can be diagnostic of the event. Such effects could potentially interfere with communications or remote sensing equipment if an impact occurred, for example, on a satellite. More seriously, impact generated plasma could end the life of a satellite by mechanisms that are not well understood and not normally taken into account in satellite design. For example, arc/discharge phenomena resulting from highly conductive plasma acting as a current path across normally shielded circuits may have contributed to the loss of the Olympus experimental communications satellite on August 11, 1993. The possibility of significant storm activity during the Leonid meteor showers of November 1998, 1999 and 2000 (impact velocity, 72 km/s) has heightened awareness of potential vulnerabilities from hypervelocity electromagnetic effects to orbital assets. The concern is justified. The amount of plasma, electrostatic charge and the magnitude of the resulting currents and electric fields scale nearly as the cube of the impact velocity. Even for microscopic Leonid impacts, the amount of plasma approaches levels that could be dangerous to spacecraft electronics. The degree of charge separation that occurs during hypervelocity impacts scales linearly with impactor mass. The resulting magnetic fields increase linearly with impactor radius and could play a significant role in our understanding of the paleomagnetism of planetary surfaces. The electromagnetic properties of plasma produced by hypervelocity impact have been exploited by researchers as a diagnostic tool, invoked to potentially explain the magnetically jumbled state of the lunar surface and blamed for the loss of the Olympus experimental communications satellite. The production of plasma in and around an impact event can lead to several effects: (1) the plasma provides a significant perturbation to the ambient magnetic field via the electromagnetic pulse; (2) it supports the production of transient radiofrequency electromagnetic fields; (3) it charges ejected debris which, because of inertial separation, leads to significant electrostatic and magnetostatic field production; and (4) its high electrical conductivity provides a convenient path for discharge of the resulting high electrostatic fields. Effects (1) and (2) have been discussed by the authors elsewhere. Effects (3) and (4) will be discussed here. Typical studies of kinetic energy warheads focus on lethality as a function of impactor momentum or energy as they couple mechanically to the target. At high enough energies, however, additional physical processes come into play. Vaporization plays an important role and a partially ionized plasma can form. Impact-generated plasma, charged debris and magnetic fields have been characterized by laboratory hypervelocity impact experiments and are shown to be more abundant when certain easily ionized materials (such as alkali metals) are used in either projectile or target.

The Waste Isolation Pilot Plant (WIPP) is a deep underground nuclear waste repository certified by the U.S. Environmental Protection Agency ,(EPA) to store transuranic defense-related waste contaminated by small amounts of radioactive materials. Located at a depth of about 655 meters below the surface, the facility is sited in southeastern New Mexico, about 40 Department of Energy underground facilities, waste disposal. kilometers east of the city of Carlsbad, New Mexico. The U.S. (DOE) managed the design and construction of the surface and and remains responsible for operation and closure following The managing and operating contractor for the DOE at the WIPP, Westinghouse Electric Corporation, maintains two rechmiant seismic monitoring systems located at the surface and in the underground. This report discusses two earthquakes detected by the seismic monitoring system, one a duratior magnitude 5.0 (Md) event located approximately 60 km east-southeast of the facility, and another a body-wave magnitude 5.6 (rob) event that occurred approximately 260 kilometers to the south-southeast.

Abstract not provided.

As an ongoing part of the collaborative efforts between the Cooperative Monitoring Center (CMC) at Sandia National Laboratories, the United States Arms Control and Disarmament Agency (ACDA), and U.S. Department of Energy (DOE), staff from the CMC served as faculty in conducting a workshop in Shanghai, China. Sponsor of the workshop was the Regional Centre for Strategic Studies (RCSS) based in Colombo, Sri Lanka. The workshop included participants from throughout South Asia and China. The CMC presented four sessions related to the role of monitoring technologies in promoting regional security and building confidence among nations. Participation in these workshops supports U.S. efforts to further regional cooperation and promote arms control, nonproliferation and other cooperative securily measures and supplements efforts funded by DOE and ACDA over the past four years. The RCSS Shanghai meeting permitted a continued CMC involvement in regionally conducted training for anew generation of leaders in government, the military, and academia throughout South Asia and China. Nuclear issues are clearly a dominant South Asian concern since the nuclear tests of May 1998. However, there remains a strong interest in identifying opportunities for increased trade and reduced tensions in other areas. The RCSS and other regional organizations are enthusiastic about continued CMC involvement in future regional courses.

A multi-attribute utility analysis is applied to the decision to select a treatment method for the management of aluminum-based spent nuclear i%el (A1-SNF) owned by the United States Department of Energy (DOE). DOE will receive, treat, and temporarily store Al- SNF, most of which is composed of highly enriched uranium, at its Savannah River Site in South Carolina. DOE intends ultimately to send the treated Al-SNJ? to a geologic repository for permanent disposal. DOE initially considered ten treatment alternatives for the management of A1-SNF, and has narrowed the choice to two of these the direct disposal and melt and dilute alternatives. The decision analysis presented in this document focuses on a decision between these two remaining alternatives.

The HI616 shipping container is a certified type B(U) packaging used by the Department of Energy (DOE) to ship tritium in support of defense programs. During the 1997 recertification of the container, DOE became concerned about the possible cracking of the polyurethane foam in the overpacks of the 2300 containers currently in service. In response, Sandia National Laboratories (SNL) initiated a radiographic inspection program to determine if cracking of the foam was occurring in the H1616 overpacks. SNL developed the radiographic technique for inspecting the foam and contracted the Savannah River Site's Tritium Engineering division to inspect a representative sample of overpacks in service. This report details the development process and the results of all of the radiography performed both at SNL and Savannah River.

As computing assumes a more central role in managing the nuclear stockpile, the consequences of an erroneous computer simulation could be severe. Computational failures are common in other endeavors and have caused project failures, significant economic loss, and loss of life. This report examines the causes of software failure and proposes steps to mitigate them. A formal verification and validation program for scientific software is recommended and described.

The research summarized in this report is the result of a two-year effort that has focused on evaluating the viability of wavelet bases for the solution of partial differential equations. The primary objective for this work has been to establish a foundation for hierarchical/wavelet simulation methods based upon numerical performance, computational efficiency, and the ability to exploit the hierarchical adaptive nature of wavelets. This work has demonstrated that hierarchical bases can be effective for problems with a dominant elliptic character. However, the strict enforcement of orthogonality was found to be less desirable than weaker semi-orthogonality or bi-orthogonality for solving partial differential equations. This conclusion has led to the development of a multi-scale linear finite element based on a hierarchical change of basis. The reproducing kernel particle method has been found to yield extremely accurate phase characteristics for hyperbolic problems while providing a convenient framework for multi-scale analyses.

Early in 1994, the Department of Energy assigned Sandia National Laboratories the responsibility for designing and providing the welding system for the girth weld for the AT-400A containment vessel. (The AT-400A container is employed for the shipment and long-term storage of the nuclear weapon pits being returned from the nation's nuclear arsenal.) Mason Hanger Corporation's Pantex Plant was chosen to be the production facility. The project was successfully completed by providing and implementing a turnkey welding system and qualified welding procedure at the Pantex Plant. The welding system was transferred to Pantex and a pilot lot of 20 AT-400A containers with W48 pits was welded in August 1997. This document is intended to bring together the AT-400A welding system and product (girth weld) requirements and the activities conducted to meet those requirements. This document alone is not a complete compilation of the welding development activities but is meant to be a summary to be used with the applicable references.

The goal is the development of materials that are highly sensitive and selective for chid chemicals and biochemical (such as insecticides, herbicides, proteins, and nerve agents) to be used as sensors, catalysts and separations membranes. Molecular modeling methods are being used to tailor chiral molecular recognition sites with high affinity and selectivity for specified agents. The work focuses on both silicate and non-silicate materials modified with chirally-pure fictional groups for the catalysis or separations of enantiomerically-pure molecules. Surfactant and quaternary amine templating is being used to synthesize porous frameworks, containing mesopores of 30 to 100 angstroms. Computer molecukw modeling methods are being used in the design of these materials, especially in the chid surface- modi~ing agents. Molecular modeling is also being used to predict the catalytic and separations selectivities of the modified mesoporous materials. The ability to design and synthesize tailored asymmetric molecular recognition sites for sensor coatings allows a broader range of chemicals to be sensed with the desired high sensitivity and selectivity. Initial experiments target the selective sensing of small molecule gases and non-toxic model neural compounds. Further efforts will address designing sensors that greatly extend the variety of resolvable chemical species and forming a predictive, model-based method for developing advanced sensors.

Comprehensive management of the battle-space has created new requirements in information management, communication, and interoperability as they effect surveillance and situational awareness. The objective of this proposal is to expand intelligent controls theory to produce a uniquely powerful implementation of distributed ground-based measurement incorporating both local collective behavior, and interoperative global optimization for sensor fusion and mission oversight. By using a layered hierarchal control architecture to orchestrate adaptive reconfiguration of autonomous robotic agents, we can improve overall robustness and functionality in dynamic tactical environments without information bottlenecks. In this concept, each sensor is equipped with a miniaturized optical reflectance modulator which is interactively monitored as a remote transponder using a covert laser communication protocol from a remote mothership or operative. Robot data-sharing at the ground level can be leveraged with global evaluation criteria, including terrain overlays and remote imaging data. Information sharing and distributed intelli- gence opens up a new class of remote-sensing applications in which small single-function autono- mous observers at the local level can collectively optimize and measure large scale ground-level signals. AS the need for coverage and the number of agents grows to improve spatial resolution, cooperative behavior orchestrated by a global situational awareness umbrella will be an essential ingredient to offset increasing bandwidth requirements within the net. A system of the type described in this proposal will be capable of sensitively detecting, tracking, and mapping spatial distributions of measurement signatures which are non-stationary or obscured by clutter and inter- fering obstacles by virtue of adaptive reconfiguration. This methodology could be used, for example, to field an adaptive ground-penetrating radar for detection of underground structures in urban environments and to detect chemical species concentrations in migrating plumes. Given is our research in these areas and a status report of our progress.

This report describes the results of a Sandia Laboratov Directed Research & Development project to develop a technique that can identifi atoms in atomically engineered nanostructures. The report provides a detailed description of the experimental measurement techniques and subsequent image analysis procedures used in the identification process, followed by examples of the technique's successful application to several atomic surface features. Use of this technique requires the experimental measurement of both constant-current topographic and multi-bias conductance data from an atomic surface with the scanning tunneling microscope. These measurements are rendered as a collection of topographic and single-bias conductance images of the surface. Image pixels are then grouped into classes by a computed grouping algorithm, according to the shared conductance characteristics exhibited at each pixel. The image pixels are then color-coded by class to produce a false-color image of the scanned surface that chemically distinguishes surface electronic features over the entire area of the measured atomic surface.

Technical support for the Hanford Tank Closure Program focused on evaluation of concepts for immobilization of residual contaminants in the Hanford AX tanks and underlying soils, and identification of cost-effective approaches to improve long-term performance of AX tank farm cIosure systems. Project objectives are to develop materials or engineered systems that would significantly reduce the radionuclide transport to the groundwater from AX tanks containing residual waste. We pursued several studies that, if implemented, would help achieve these goals. They include: (1) tank fill design to reduce water inilltration and potential interaction with residual waste; (2) development of in-tank getter materials that would specifically sorb or sequester radionuclides; (3) evaluation of grout emplacement under and around the tanks to prevent waste leakage during waste retrieval or to minimize water infiltration beneath the tanks; (4) development of getters that will chemically fix specific radionuclides in soils under tanks; and (5) geochemical and hydrologic modeling of waste-water-soil-grout interactions. These studies differ in scope from the reducing grout tank fill employed at the Savannah River Site in that our strategy improves upon tank fill design by providing redundancy in the barriers to radionuclide migration and by modification the hydrogeochemistry external to the tanks.

Abstract not provided.

Sol-gel chemistry has been the focus of much attention in the design and preparation of highly crosslinked polysiloxane gels. Preparation of sol-gel processed silica or polysilesquioxane gels is carried out by the hydrolysis and condensation of alkoxysilyl monomers, usually in the presence of catalytic acid or base and an excess of water. Removal of the alcohol and water byproducts of the condensation reactions, in addition to the alcohol needed to co-dissolve the hydrophobic monomers with water, leads to substantial shrinkage during drying of the resulting gels. This limits the utility of sol-gel processing for applications requiring net-shape casting of artifacts, crack free coatings, or low vaporous organic contaminants (VOCs). It would be advantageous to have a sol-gel process based on an organosilicon monomer that would not require water as a reactant or produce water and alcohol condensation products and still result in siloxane network polymers capable of forming gels. Here, the authors show the synthesis and preparation of a novel sol-gel monomer which can easily be polymerized by ring opening polymerization to give highly crosslinked polysiloxane gels with no condensation byproducts.

An air sparging and high vacuum extraction was installed as an alternative to a containment pump and treat system to reduce the long-term remediation schedule. The site is located at the DOE Mound facility in Miamisburg, Ohio, just south of Dayton. The air sparging system consists of 23 wells interspersed between 17 soil vapor extraction wells. The SVE system has extracted about 1,500 lbs of VOCs in five months. The air sparging system operated for about 6 weeks before shutdown due to suspected biochemical fouling. Technical data are presented on the operating characteristics of the system.

Advanced radiographic applications require a constant source size less than 1 mm. To study the time history of a relativistic electron beam as it interacts with a bremsstrahlung converter, one of the diagnostics they use is a multi-frame time-resolved hard x-ray camera. They are performing experiments on the ETA-II accelerator at Lawrence Livermore National Laboratory to investigate details of the electron beam/converter interactions. The camera they are using contains 6 time-resolved images, each image is a 5 ns frame. By starting each successive frame 10 ns after the previous frame, they create a 6-frame movie from the hard x-rays produced from the interaction of the 50-ns electron beam pulse.

The authors report 77K operation of an optically pumped vertical cavity surface emitting laser with an Sb-based cavity. The structure consists of 15 and 20 pair AlGaAsSb/AlAsSb top and bottom reflectors and a bulk InGaAs active region.