Titanium hydride of varying TiH stoichiometry is used in pyrotechnic compositions. In order to yield consistent performance, manufacturing processes must be developed to ensure precise and reproducible material properties, including composition and morphology. Legacy synthesis protocols are not comprehensive nor are the required apparatuses still available. To guide the development of novel production procedures, this report reviews literature on relevant chemical reactions and diffusion events occurring at elevated temperature in the TiH(2-x)/TiOy system. Titanium hydride exposed to air spontaneously forms a passivating oxide layer. Upon heating, significant hydrogen release, which is accompanied by changes to the surface oxide layer, is noted by 375–400°C. At higher temperatures (above about 500°C) the oxide layer is reported to be essentially nonexistent as a result of oxide-layer dissolution processes and, potentially, oxide-layer reduction due to water formation. Based on the reviewed literature, we hypothesize that, by 500°C, the surface layer consists of an oxyhydride phase, which is a solid solution of oxygen in titanium hydride. We believe that hydrogen release from titanium hydride is controlled by the kinetics of molecular hydrogen desorption on the oxyhydride surface. No literature data is available for corresponding activation energies of the dynamic desorption process, and the equilibrium phase diagram of this three-component system remains largely unexplored as well. These gaps in knowledge might be addressed through coordinated computational modeling and experimental efforts.
In-situ transmission electron microscopy (TEM) provides an avenue to explore time-dependent nanoscale material changes induced by a wide range of environmental conditions that govern material performance and degradation. The In-situ Ion Irradiation TEM (I3TEM) at Sandia National Laboratories is a JEOL 2100 microscope that has been highly modified with an array of hardware and software that makes it particularly well suited to explore fundamental mechanisms that arise from coupled extreme conditions. Here, examples pertaining to multibeam ion irradiation, rapid thermal cycling, and nanomechanical testing on the I3TEM are highlighted, along with prospective advancements in the field of in-situ microscopy.
Particle characteristics can drastically influence the process-structure-property-performance aspects of granular materials in compression. We aim to computationally simulate the mechanical processes of stress redistribution in compacts including the kinematics of particle rearrangement during densification and particle deformation leading to fragmentation. Confined compression experiments are conducted with three sets of commercial microcrystalline cellulose particles nearly spherical in shape with different mean particle size. Experimentally measured compression curves from tall powder columns are fitted with the Kenkre et al. (J. of American Chemical Society, Vol. 79, No. 12) model. This model provides a basis to derive several common two-parameter literature models and as a framework to incorporate statistical representations of critical particle behaviors. We focus on the low-stress compression data and the model comparisons typically not discussed in the literature. Additional single particle compressions report fracture strength with particle size for comparison to the apparent particle strength extracted from bulk compression data.
Mitigating corrosion remains a daunting challenge due to localized, nanoscale corrosion events that are poorly understood but are known to cause unpredictable variations in material longevity. Here, the most recent advances in liquid-cell transmission electron microscopy were employed to capture the advent of localized aqueous corrosion in carbon steel at the nanoscale and in real time. Localized corrosion initiated at a triple junction formed by a solitary cementite grain and two ferrite grains and then continued at the electrochemically-active boundary between these two phases. With this analysis, we identified facetted pitting at the phase boundary, uniform corrosion rates from the steel surface, and data that suggest that a re-initiating galvanic corrosion mechanism is possible in this environment. These observations represent an important step toward atomically defining nanoscale corrosion mechanisms, enabling the informed development of next-generation inhibition technologies and the improvement of corrosion predictive models.
Nanostructures may be exposed to irradiation during their manufacture, their engineering and whilst in-service. The consequences of such bombardment can be vastly different from those seen in the bulk. In this paper, we combine transmission electron microscopy with in situ ion irradiation with complementary computer modelling techniques to explore the physics governing the effects of 1.7 MeV Au ions on gold nanorods. Phenomena surrounding the sputtering and associated morphological changes caused by the ion irradiation have been explored. In both the experiments and the simulations, large variations in the sputter yields from individual nanorods were observed. These sputter yields have been shown to correlate with the strength of channelling directions close to the direction in which the ion beam was incident. Craters decorated by ejecta blankets were found to form due to cluster emission thus explaining the high sputter yields.
A new technical basis on the mechanics of energetic materials at the individual particle scale has been developed. Despite these particles being in most of our Sandia non-nuclear explosive components, we have historically lacked any understanding of particle behavior. Through the novel application of nanoidentation methods to single crystal films and single particles of energetic materials with complex shapes, discovery data has been collected elucidating phenomena of particle strength, elastic and plastic deformation, and fracture. This work specifically developed the experimental techniques and analysis methodologies to distill data into relationships suitable for future integration into particle level simulations of particle reassembly. This project utilized experimental facilities at CINT and the Explosive Components Facility to perform ex-situ and in-situ nanoidentation experiments with simultaneous scanning electron microscope (SEM) imaging. Data collected by an applied axial compressive load in either force-control or displacement-control was well represented by Hertzian contact theory for linear elastic materials. Particle fracture phenomenology was effectively modeled by an empirical damage model.
