Publications

We postulate that there is a required velocity of magnetic flux into a plasma-armature railgun to keep the armature from expanding toward the breech and thereby changing the nature of the forward-going force. Testing this idea with data from several guns we find confirmation, provided the required flux velocity increases with the square of the linear current density. This leads to the conclusion that these guns have a momentum limit while they are operating as true electromagnetic launchers. That limit is derived. High-performance railguns reach this limit during current rise, and most of their momentum comes from a hybrid phase. The hybrid phase has a pressure limitation at high velocity similar to electrothermal, light-gas, and powder guns. The 6 km/s “velocity limit” is explained by this pressure limitation. © 1993 IEEE

Different hardness-assurance tests are often required for advanced bipolar devices than for CMOS devices. In this work, the dose-rate dependence of bipolar current-gain degradation is mapped over a wide range of dose rates for the first time, and it is very different from analogous MOSFET curves. Annealing experiments following irradiation show negligible change in base current at room temperature, but significant recovery at temperatures of 100°C and above. In contrast to what is observed in MOSFET’s, irradiation and annealing tests cannot be used to predict the low-dose-rate response of bipolar devices. A comparison of x-ray-induced and 60Co gamma-ray-induced gain degradation is reported for the first time for bipolar transistors. The role of the emitter bias during irradiation is also examined. Implications for hardening and hardness assurance are discussed. © 1993 IEEE

Vadose-zone moisture transport near an impermeable barrier has been under study at a field site near Albuquerque, NM since 1990. Moisture content and temperature have been monitored in the subsurface on a regular basis; both undergo a seasonal variation about average values. Even though the slab introduces two-dimensional effects on the scale of the slab, moisture and heat transport is predominantly vertical. Numerical simulations, based on the models developed by Philip and de Vries (1957) and de Vries (1958), indicate that the heat flow is conduction-dominated while the moisture movement is dominated by diffusive vapor distillation. Model predictions of the magnitude and extent of changes in moisture content underneath the slab are in reasonable agreement with observation.

A Sandia National Laboratories/AT&T Bell Laboratories Team is developing a soft x-ray projection lithography tool that uses a compact laser plasma as a source of 14 nm x-rays. Optimization of the 14 nm x-rays source brightness is a key issue in this research. This paper describes our understanding of the source as it has been obtained through the use of computer simulations utilizing the LASNEX radiation-hydrodynamics code.

Ion-beam-induced charge-collection imaging (IBICC) has been used to study the SEU mechanisms of the Sandia TA670 16K-bit SRAM. Quantitative charge-collection spectra from known regions of the memory cell have been derived with this technique. For 2.4-MeV He ions at normal incidence, charge collection depth for a reverse-biased p+ drain strike is estimated to be 4.8±0.4 μm. Heavy-ion strikes to the reverse-biased p-well result in nearly complete collection of deposited charge to a depth of 5.5±0.5 μm. A charge amplification effect in the n-on drain is identified and is due to either bipolar amplification or a shunt effect in the parasitic vertical npn bipolar transistor associated with the n+/n substrate, p-well, and n+ drain. This effect is present only when the n+ drain is at 0V bias. When coupled with previous SEU-imaging, these results strongly suggest that the dominant SEU mechanism in this SRAM is a heavy-ion strike to the n-on transistor drain. © 1993 IEEE

The Vapnik-Chervonenkis (V-C) dimension is an important combinatorial tool in the analysis of learning problems in the PAC framework. For polynomial learnability, we seek upper bounds on the V-C dimension that are polynomial in the syntactic complexity of concepts. Such upper bounds are automatic for discrete concept classes, but hitherto little has been known about what general conditions guarantee polynomial bounds on V-C dimension for classes in which concepts and examples are represented by tuples of real numbers. In this paper, we show that for two general kinds of concept class the V-C dimension is polynomially bounded as a function of the syntactic complexity of concepts. One is classes where the criterion for membership of an instance in a concept can be expressed as a formula (in the first-order theory of the reals) with fixed quantification depth and exponentially-bounded length, whose atomic predicates are polynomial inequalities of exponentially-bounded degree. The other is classes where containment of an instance in a concept is testable in polynomial time, assuming we may compute standard arithmetic operations on reals exactly in constant time. Our results show that in the continuous case, as in the discrete, the real barrier to efficient learning in the Occam sense is complexity-theoretic and not information-theoretic. We present examples to show how these results apply to concept classes defined by geometrical figures and neural nets, and derive polynomial bounds on the V-C dimension for these classes.

During hydrocarbon reservoir stimulations, such as hydraulic fracturing, the cracking and slippage of the formation results in the emission of seismic energy. The objective of this study was to determine the properties of these induced micro-seisms. A hydraulic fracture experiment was performed in the Piceance Basin of Western Colorado to induce and record micro-seismic events. The formation was subjected to four processes; breakdown/ballout, step-rate test, KCL mini-fracture, and linear-gel mini-fracture. Micro-seisms were acquired with an advanced three-component wall-locked seismic accelerometer package, placed in an observation well 211 ft offset from the fracture well. During the two hours of formation treatment, more than 1200 micro-seisms with signal-to-noise ratios in excess of 20 dB were observed. The observed micro- seisms had a nominally flat frequency spectrum from 100 Hz to 1500 Hz and lack the spurious tool-resonance effects evident in previous attempts to measure micro-seisms. Both p-wave and s-wave arrivals are clearly evident in the data set, and hodogram analysis yielded coherent estimates of the event locations. This paper describes the characteristics of the observed micro- seismic events (event occurrence, signal-to-noise ratios, and bandwidth) and illustrates that the new acquisition approach results in enhanced detectability and event location resolution.

Many designs use EPLDs (Erasable Programmable Logic Devices) to implement control logic and state machines. If the design is slow, timing through the EPLD is not crucial so designers often treat the device as a black box. In high speed designs, timing through the EPLD is critical. In these cases a thorough understanding of the device architecture is necessary. Lessons learned in the implementation of a high-speed design using the Altera EPM5130 are discussed.

A new Assembly Test Chip, ATC04, designed to measure mechanical stresses at the die surface has been built and tested. This CMOS chip 0.25 in. on a side, has an array of 25 piezoresistive stress sensing cells, four resistive heaters and two ring oscillators. The ATCO4 chip facilitates making stress measurements with relatively simple test equipment and data analysis. The design, use, and accuracy of the chip are discussed and initial results are presented from three types of stress measurement experiments: four-point bending calibration, single point bending of a substrate with an ATC04 attached by epoxy, and stress produced by a liquid epoxy encapsulant.

The feasibility of utilizing a groundbased laser without an orbital mirror for space debris removal is examined. Technical issues include atmospheric transmission losses, adaptive-optics corrections of wavefront distortions, laser field-of-view limitations, and laser-induced impulse generation. The physical constraints require a laser with megawatt output, long run-time capability, and wavelength with good atmospheric transmission characteristics. It is found that a 5-MW reactor-pumped laser can deorbit debris having masses of the order of one kilogram from orbital altitudes to be used by Space Station Freedom. Debris under one kilogram can be deorbited after one pass over the laser site, while larger debris can be deorbited or transferred to alternate orbits after multiple passes over the site.

Flux-flow based devices such as the superconducting flux flow transistor and magnetically controlled long junctions have been made from thin films of TICaBaCuO and YBaCuO. The devices are based on the magnetic control of flux flow in their respective structures: a long junction or an array of weak links. The equivalent circuits of the two devices are similar: a low impedance input control line, an output impedance of 3-20 Q and an active current-controlled element. The long junctions have tended to be slower, have lower gain and be somewhat less noisy than their counterparts. The performance of circuits such as narrowband and distributed amplifiers (SO GHz bandwidths, noise figures < 3 dB), phase shifters (continuous with < 2 dB loss 4-40 GHz), logic gates (2-3 ps gate delays) and memories made using these devices will be compared and analyzed. © 1993 IEEE

Automatic motion planning of a spray cleaning robot with collision avoidance is presented in this paper. In manufacturing environments, electronic and mechanical components are traditionally cleaned by spraying or dipping them using chlorofluorocarbon (CFC) solvents. As new scientific data show that such solvents are major causes for stratospheric ozone depletion, an alternate cleaning method is needed. Part cleaning with aqueous solvents is environmentally safe, but can require precision spraying at high pressures for extended time periods. Operator fatigue during manual spraying can decrease the quality of the cleaning process. By spraying with a robotic manipulator, the necessary spray accuracy and consistency to manufacture high-reliability components can be obtained. Our motion planner was developed to automatically generate motions for spraying robots based on the part geometry and cleaning process parameters. For spraying paint and other coatings a geometric description of the parts and robot may be sufficient for motion planning, since coatings are usually done over the visible surfaces. For spray cleaning, the requirement to reach hidden surfaces necessitates the addition of a rule-based method to the geometric motion planning.

The geochemical properties of a porous sand and several tracers (Ni, Br, and Li) have been characterized for use in a caisson experiment designed to validate sorption models used in models of reactive transport. The surfaces of the sand grains have been examined by a combination of techniques including potentiometric titration, acid leaching, optical microscopy, and scanning electron microscopy with energy-dispersive spectroscopy. The surface studies indicate the presence of small amounts of carbonate, kaolinite and iron-oxyhydroxides. Adsorption of nickel, lithium and bromide by the sand was measured using batch techniques. Bromide was not sorbed by the sand. A linear (Kd) or an isotherm sorption model may adequately describe transport of Li; however, a model describing the changes of pH and the concentrations of other solution species as a function of time and position within the caisson and the concomitant effects on Ni sorption may be required for accurate predictions of nickel transport.

For problems where media properties are measured at one scale and applied at another, scaling laws or models must be used in order to define effective properties at the scale of interest. The accuracy of such models will play a critical role in predicting flow and transport through the Yucca Mountain Test Site given the sensitivity of these calculations to the input property fields. Therefore, a research program has been established to gain a fundamental understanding of how properties scale with the aim of developing and testing models that describe scaling behavior in a quantitative manner. Scaling of constitutive rock properties is investigated through physical experimentation involving the collection of suites of gas permeability data measured over a range of discrete scales. Also, various physical characteristics of property heterogeneity and the means by which the heterogeneity is measured and described and systematically investigated to evaluate their influence on scaling behavior. This paper summarizes the approach that is being taken toward this goal and presents the results of a scoping study that was conducted to evaluate the feasibility of the proposed research.

Experimental results exploring gravity-driven wetting front instability in a pre-wetted, rough-walled analog fracture are presented. Initial conditions considered include a uniform moisture field wetted to field capacity of the analog fracture and the structured moisture field created by unstable infiltration into an initially dry fracture. As in previous studies performed under dry initial conditions, instability was found to result both at the cessation of stable infiltration and at flux lower than the fracture capacity under gravitational driving force. Individual fingers were faster, narrower, longer, and more numerous than observed under dry initial conditions. Wetting fronts were found to follow existing wetted structure, providing a mechanism for rapid recharge and transport.

In an attempt to achieve completeness and consistency, the performance-assessment analyses developed by the Yucca Mountain Project are tied to scenarios described in event trees. Development of scenarios requires describing the constituent features, events, and processes in detail. Several features and processes occurring at the waste packages and the rock immediately surrounding the packages (i.e., the near field) have been identified: the effects of radiation on fluids in the near-field rock, the path-dependency of rock-water interactions, and the partitioning of contaminant transport between colloids and solutes. This paper discusses some questions regarding these processes that the near-field performance-assessment modelers will need to have answered to specify those portions of scenarios dealing with the near field.

Experiments investigating the behavior of individual, gravity-driven fingers in an initially dry, rough-walled analog fracture are presented. Fingers were initiated from constant flow to a point source. Finger structure is described in detail; specific phenomena observed include: desaturation behind the finger-tip, variation in finger path, intermittent flow structures, finger-tip bifurcation, and formation of dendritic sub-fingers. Measurements were made of finger-tip velocity, finger width, and finger-tip length. Non-dimensional forms of the measured variables are analyzed relative to the independent parameters, flow rate and gravitational gradient.

The potential repository system is intended to isolate high-level radioactive waste at Yucca Mountain according to the performance objective - 10 CFR 60.112. One subsystem that may contribute to achieving this objective is the sealing subsystem. This subsystem is comprised of sealing components in the shafts, ramps, underground network of drifts, and the exploratory boreholes. Sealing components can be rigid, as in the case of a shaft seal, or can be more compressible, as in the case of drift fill comprised of mined rockfill. This paper presents the preliminary seismic response of discrete sealing components in welded and nonwelded tuff. Special consideration is given to evaluating the stress in the seal, and the behavior of the interface between the seal and the rock. The seismic responses are computed using both static and dynamic analyses. Also presented is an evaluation of the maximum seismic response encountered by a drift seal with respect to the angle of incidence of the seismic wave. Mitigation strategies and seismic design considerations are proposed which can potentially enhance the overall response of the sealing component and subsequently, the performance of the overall repository system.

This analytical study examines the effect of initial thermodynamic conditions on the loads generated by the combustion of homogeneous hydrogen-air-steam mixtures. The effect of initial temperature, pressure, hydrogen concentration, and steam concentration is evaluated for two cases, (1) constant volume and (2) constant initial pressure. For each case, the Adiabatic, Isochoric, Complete Combustion (AICC), Chapman-Jouguet (CJ), and normally reflected CJ pressures are calculated for a range of hydrogen and steam concentrations representative of the entire flammable regime. For detonation loads, pressure profiles and time-histories are also evaluated in one-dimensional Cartesian geometry. The results show that to a first approximation, the AICC and CJ pressures are directly proportional to the initial density. Increasing the hydrogen concentration up to stoichiometric concentrations significantly increases the AICC, CJ, and reflected CJ pressures. For the constant volume case, the AICC, CJ, and reflected CJ pressures increase with increasing hydrogen concentration on the rich side of stoichiometric concentrations. For the constant initial pressure case, the AICC, CJ, and reflected CJ pressures decrease with increasing hydrogen concentration on the rich side of stoichiometric values. The addition of steam decreases the AICC, CJ, and reflected CJ pressures for the constant initial pressure case, but increases them for the constant volume case. For detonations, the pressure time-histories can be normalized with the AICC pressure and the reverberation time for Cartesian geometry. © 1993.

We present a new methodology for predicting the fatigue life of solder joints for electronics applications. This approach involves the integration of experimental and computational techniques. The first stage involves correlating the manufacturing and processing parameters with the starting microstructure of the solder joint. The second stage involves a series of experiments that characterize the evolution of the microstructure during thermal cycling. The third stage consists of a computer modeling and simulation effort that utilizes the starting microstructure and experimental data to produce a reliability prediction of the solder joint. This approach is an improvement over current methodologies because it incorporates the microstructure and properties of the solder directly into the model and allows these properties to evolve as the microstructure changes during fatigue.

The results of experiments on the energy losses in switches are presented. All experiments were circuit code modeled after the development of a new switch loss version based on Braginskii's spark channel theory for gasses. The circuit code predicts switch energy loss and peak currents as a function of time. Slight constant offsets between the theory and data that depended on the switching dielectric were observed. Plasma conductivity for each tested dielectric was modified to lessen this offset. An excellent agreement between the theory and experiment was also observed. The new model successfully predicted the series resistance of Marx generators.

Yucca Mountain, Nevada is a potential site for a high-level radioactive-waste repository. Uncertainty and sensitivity analyses were performed to estimate critical factors in the performance of the site with respect to a criterion in terms of pre-waste-emplacement ground-water travel time. The degree of failure in the analytical model to meet the criterion is sensitive to the estimate of fracture porosity in the upper welded unit of the problem domain. Fracture porosity is derived from a number of more fundamental measurements including fracture frequency, fracture orientation, and the moisture-retention characteristic inferred for the fracture domain.

This report contains an outline of the Solar Thermal Design Assistance Center's (STDAC) major activities and accomplishments in Fiscal Year 1992 (FY92). The report describes the resources allocated to fund STDAC and the personnel needed to carry out STDAC activities and accomplishments. It also contains a comprehensive list of persons that called STDAC for consultation in FY92.

Images taken with a synthetic aperture radar (SAR) on an airplane were distorted with phase errors generated by a computer program that simulates the propagation of radar waves through the disturbed ionosphere. The simulation is for an orbiting SAR imaging a scene on the ground. Both the spatially-invariant (decorrelation length projected onto the ground much larger than the scene size) and spatially-variant (decorrelation length much smaller than the scene size) cases are described. The spatially-invariant phase errors can be removed using several different algorithms. Problems and strategies in restoring SAR images distorted with spatially-variant phase errors are discussed.

Future challenges facing the nonproliferation community will undoubtedly change the normal way of doing business'' in international safeguards. New technology will emerge in support of compliance concepts such as transparency and openness, regional security assurance, bilateral cooperation, and special. or non-routine inspections. Technologies address in remote unattended monitoring, integrated on-site monitoring, environmental monitoring, satellite and aerial over-flight systems, equipment for special inspectios, and sharable data information fusion and management, are just a few examples of potential technologics for new nonproliferation monitoring regimes.