Publications

Abstract not provided.

High-power 18650 Li-ion cells have been developed for hybrid electric vehicle applications as part of the DOE FreedomCAR Advanced Technology Development (ATD) program. Cells have been developed for high-power, long-life, low-cost and abuse tolerance conditions. The thermal abuse response of advanced materials and cells were measured and compared. Cells were constructed for determination of abuse tolerance to determine the thermal runaway response and flammability of evolved gas products during venting. Advanced cathode and anode materials were evaluated for improved tolerance under abusive conditions. Calorimetric methods were used to measure the thermal response and properties of the cells and cell materials up to 450 °C. Improvements in thermal runaway response have been shown using combinations of these materials.

We report results from an investigation of the two-color polarization spectroscopy (TC-PS) and two-color six-wave mixing (TC-SWM) techniques for the measurement of atomic hydrogen in flames. The 243-nm two-photon pumping of 1S-2S transition of the H-atom was followed by single-photon probing of the 2S-3P transition at 656 nm. Necessary laser radiation was generated using two distributed feedback dye lasers (DFDLs) pumped by two regeneratively amplified, picosecond, Nd:YAG lasers. The DFDL pulses are nearly Fourier transform limited and have a pulse width of approximately 80 ps. The effects of pump and probe beam polarizations on the TC-PS and TC-SWM signals were studied in detail. The collisional dynamics of the H(2l) level were also investigated in an atmospheric-pressure hydrogenair flame by scanning the time delay between the pump and probe pulses. An increase in signal intensity of approximately 100 was observed in the TC-SWM geometry as compared to the TC-PS geometry.

Currently, pathologists rely on labor-intensive microscopic examination of tumor cells using century-old staining methods that can give false readings. Emerging BioMicroNano-technologies have the potential to provide accurate, realtime, high-throughput screening of tumor cells without the need for time-consuming sample preparation. These rapid, nano-optical techniques may play an important role in advancing early detection, diagnosis, and treatment of disease. In this report, we show that laser scanning confocal microscopy can be used to identify a previously unknown property of certain cancer cells that distinguishes them, with single-cell resolution, from closely related normal cells. This property is the correlation of light scattering and the spatial organization of mitochondria. In normal liver cells, mitochondria are highly organized within the cytoplasm and highly scattering, yielding a highly correlated signal. In cancer cells, mitochondria are more chaotically organized and poorly scattering. These differences correlate with important bioenergetic disturbances that are hallmarks of many types of cancer. In addition, we review recent work that exploits the new technology of nanolaser spectroscopy using the biocavity laser to characterize the unique spectral signatures of normal and transformed cells. These optical methods represent powerful new tools that hold promise for detecting cancer at an early stage and may help to limit delays in diagnosis and treatment. ©Adenine Press (2005).

Abstract not provided.

Ion mobility spectrometry (IMS) is recognized as one of the most sensitive and versatile techniques for the detection of trace levels of organic vapors. IMS is widely used for detecting contraband narcotics, explosives, toxic industrial compounds and chemical warfare agents. Increasing threat of terrorist attacks, the proliferation of narcotics, Chemical Weapons Convention treaty verification as well as humanitarian de-mining efforts has mandated that equal importance be placed on the analysis time as well as the quality of the analytical data. (1) IMS is unrivaled when both speed of response and sensitivity has to be considered. (2) With conventional (signal averaging) IMS systems the number of available ions contributing to the measured signal to less than 1%. Furthermore, the signal averaging process incorporates scan-to-scan variations decreasing resolution. With external second gate Fourier Transform ion mobility spectrometry (FT-IMS), the entrance gate frequency is variable and can be altered in conjunction with other data acquisition parameters to increase the spectral resolution. The FT-IMS entrance gate operates with a 50% duty cycle and so affords a 7 to 10-fold increase in sensitivity. Recent data on high explosives are presented to demonstrate the parametric optimization in sensitivity and resolution of our system.

This report summarizes the work performed as part of a one-year LDRD project, 'Evolutionary Complexity for Protection of Critical Assets.' A brief introduction is given to the topics of genetic algorithms and genetic programming, followed by a discussion of relevant results obtained during the project's research, and finally the conclusions drawn from those results. The focus is on using genetic programming to evolve solutions for relatively simple algebraic equations as a prototype application for evolving complexity in computer codes. The results were obtained using the lil-gp genetic program, a C code for evolving solutions to user-defined problems and functions. These results suggest that genetic programs are not well-suited to evolving complexity for critical asset protection because they cannot efficiently evolve solutions to complex problems, and introduce unacceptable performance penalties into solutions for simple ones.

The Sandia National Laboratories Corporate Mentor Program provides a mechanism for the development and retention of Sandia's people and knowledge. The relationships formed among staff members at different stages in their careers offer benefits to all. These relationships can provide experienced employees with new ideas and insight and give less experienced employees knowledge of Sandia's culture, strategies, and programmatic direction. The program volunteer coordinators are dedicated to the satisfaction of the participants, who come from every area of Sandia. Since its inception in 1995, the program has sustained steady growth and excellent customer satisfaction. This report summarizes the accomplishments, activities, enhancements, and evaluation data for the Corporate Mentor Program for the 2003/2004 program year ending May 1, 2004.

This SAND report provides the technical progress through June 2004 of the Sandia-led project, ''Carbon Sequestration in Synechococcus Sp.: From Molecular Machines to Hierarchical Modeling'', funded by the DOE Office of Science Genomes to Life Program. Understanding, predicting, and perhaps manipulating carbon fixation in the oceans has long been a major focus of biological oceanography and has more recently been of interest to a broader audience of scientists and policy makers. It is clear that the oceanic sinks and sources of CO{sub 2} are important terms in the global environmental response to anthropogenic atmospheric inputs of CO{sub 2} and that oceanic microorganisms play a key role in this response. However, the relationship between this global phenomenon and the biochemical mechanisms of carbon fixation in these microorganisms is poorly understood. In this project, we will investigate the carbon sequestration behavior of Synechococcus Sp., an abundant marine cyanobacteria known to be important to environmental responses to carbon dioxide levels, through experimental and computational methods. This project is a combined experimental and computational effort with emphasis on developing and applying new computational tools and methods. Our experimental effort will provide the biology and data to drive the computational efforts and include significant investment in developing new experimental methods for uncovering protein partners, characterizing protein complexes, identifying new binding domains. We will also develop and apply new data measurement and statistical methods for analyzing microarray experiments. Computational tools will be essential to our efforts to discover and characterize the function of the molecular machines of Synechococcus. To this end, molecular simulation methods will be coupled with knowledge discovery from diverse biological data sets for high-throughput discovery and characterization of protein-protein complexes. In addition, we will develop a set of novel capabilities for inference of regulatory pathways in microbial genomes across multiple sources of information through the integration of computational and experimental technologies. These capabilities will be applied to Synechococcus regulatory pathways to characterize their interaction map and identify component proteins in these pathways. We will also investigate methods for combining experimental and computational results with visualization and natural language tools to accelerate discovery of regulatory pathways. The ultimate goal of this effort is develop and apply new experimental and computational methods needed to generate a new level of understanding of how the Synechococcus genome affects carbon fixation at the global scale. Anticipated experimental and computational methods will provide ever-increasing insight about the individual elements and steps in the carbon fixation process, however relating an organism's genome to its cellular response in the presence of varying environments will require systems biology approaches. Thus a primary goal for this effort is to integrate the genomic data generated from experiments and lower level simulations with data from the existing body of literature into a whole cell model. We plan to accomplish this by developing and applying a set of tools for capturing the carbon fixation behavior of complex of Synechococcus at different levels of resolution. Finally, the explosion of data being produced by high-throughput experiments requires data analysis and models which are more computationally complex, more heterogeneous, and require coupling to ever increasing amounts of experimentally obtained data in varying formats. These challenges are unprecedented in high performance scientific computing and necessitate the development of a companion computational infrastructure to support this effort.

This manual describes the input syntax to the ALEGRA radiation transport package. All input and output variables are defined, as well as all algorithmic controls. This manual describes the radiation input syntax for ALEGRA-HEDP. The ALEGRA manual[2] describes how to run the code and general input syntax. The ALEGRA-HEDP manual[13] describes the input for other physics used in high energy density physics simulations, as well as the opacity models used by this radiation package. An emission model, which is the lowest order radiation transport approximation, is also described in the ALEGRA-HEDP manual. This document is meant to be used with these other manuals.

ALEGRA is an arbitrary Lagrangian-Eulerian finite element code that emphasizes large distortion and shock propagation in inviscid fluids and solids. This document describes user options for modeling resistive magnetohydrodynamic, thermal conduction, and radiation emission effects.

Mobile manipulator systems used by emergency response operators consist of an articulated robot arm, a remotely driven base, a collection of cameras, and a remote communications link. Typically the system is completely teleoperated, with the operator using live video feedback to monitor and assess the environment, plan task activities, and to conduct the operations via remote control input devices. The capabilities of these systems are limited, and operators rarely attempt sophisticated operations such as retrieving and utilizing tools, deploying sensors, or building up world models. This project has focused on methods to utilize this video information to enable monitored autonomous behaviors for the mobile manipulator system, with the goal of improving the overall effectiveness of the human/robot system. Work includes visual servoing, visual targeting, utilization of embedded video in 3-D models, and improved methods of camera utilization and calibration.

Treatment systems that can neutralize biological agents are needed to mitigate risks from novel and legacy biohazards. Tests with Bacillus thuringiensis and Bacillus steurothemophilus spores were performed in a 190-liter, 1-112 lb TNT equivalent rated Explosive Destruction System (EDS) system to evaluate its capability to treat and destroy biological agents. Five tests were conducted using three different agents to kill the spores. The EDS was operated in steam autoclave, gas fumigation and liquid decontamination modes. The first three tests used EDS as an autoclave, which uses pressurized steam to kill the spores. Autoclaving was performed at 130-140 deg C for up to 2-hours. Tests with chlorine dioxide at 750 ppm concentration for 1 hour and 10% (vol) aqueous chlorine bleach solution for 1 hour were also performed. All tests resulted in complete neutralization of the bacterial spores based on no bacterial growth in post-treatment incubations. Explosively opening a glass container to expose the bacterial spores for treatment with steam was demonstrated and could easily be done for chlorine dioxide gas or liquid bleach.

We have developed a novel approach to modeling the transmembrane spanning helical bundles of integral membrane proteins using only a sparse set of distance constraints, such as those derived from MS3-D, dipolar-EPR and FRET experiments. Algorithms have been written for searching the conformational space of membrane protein folds matching the set of distance constraints, which provides initial structures for local conformational searches. Local conformation search is achieved by optimizing these candidates against a custom penalty function that incorporates both measures derived from statistical analysis of solved membrane protein structures and distance constraints obtained from experiments. This results in refined helical bundles to which the interhelical loops and amino acid side-chains are added. Using a set of only 27 distance constraints extracted from the literature, our methods successfully recover the structure of dark-adapted rhodopsin to within 3.2 {angstrom} of the crystal structure.

We report a new nanolaser technique for measuring characteristics of human mitochondria. Because mitochondria are so small, it has been difficult to study large populations using standard light microscope or flow cytometry techniques. We recently discovered a nano-optical transduction method for high-speed analysis of submicron organelles that is well suited to mitochondrial studies. This ultrasensitive detection technique uses nano-squeezing of light into photon modes imposed by the ultrasmall organelle dimensions in a semiconductor biocavity laser. In this paper, we use the method to study the lasing spectra of normal and diseased mitochondria. We find that the diseased mitochondria exhibit larger physical diameter and standard deviation. This morphological differences are also revealed in the lasing spectra. The diseased specimens have a larger spectral linewidth than the normal, and have more variability in their statistical distributions.

The brain is often identified with decision-making processes in the biological world. In fact, single cells, single macromolecules (proteins) and populations of molecules also make simple decisions. These decision processes are essential to survival and to the biological self-assembly and self-repair processes that we seek to emulate. How do these tiny systems make effective decisions? How do they make decisions in concert with a cooperative network of other molecules or cells? How can we emulate the decision-making behaviors of small-scale biological systems to program and self-assemble microsystems? This LDRD supported research to answer these questions. Our work included modeling and simulation of protein populations to help us understand, mimic, and categorize molecular decision-making mechanisms that nonequilibrium systems can exhibit. This work is an early step towards mimicking such nanoscale and microscale biomolecular decision-making processes in inorganic systems.

Chemically prepared zinc oxide powders are fabricated for the production of high aspect ratio varistor components. Colloidal processing in water was performed to reduce agglomerates to primary particles, form a high solids loading slurry, and prevent dopant migration. The milled and dispersed powder exhibited a viscoelastic to elastic behavioral transition at a volume loading of 43-46%. The origin of this transition was studied using acoustic spectroscopy, zeta potential measurements and oscillatory rheology. The phenomenon occurs due to a volume fraction solids dependent reduction in the zeta potential of the solid phase. It is postulated to result from divalent ion binding within the polyelectrolyte dispersant chain, and was mitigated using a polyethylene glycol plasticizing additive. Chemically prepared zinc oxide powders were processed for the production of high aspect ratio varistor components. Near net shape casting methods including slip casting and agarose gelcasting were evaluated for effectiveness in achieving a uniform green microstructure achieving density values near the theoretical maximum during sintering. The structure of the green parts was examined by mercury porisimetry. Agarose gelcasting produced green parts with low solids loading values and did not achieve high fired density. Isopressing the agarose cast parts after drying raised the fired density to greater than 95%, but the parts exhibited catastrophic shorting during electrical testing. Slip casting produced high green density parts, which exhibited high fired density values. The electrical characteristics of slip cast parts are comparable with dry pressed powder compacts. Alternative methods for near net shape forming of ceramic dispersions were investigated for use with the chemically prepared ZnO material. Recommendations for further investigation to achieve a viable production process are presented.

ALEGRA is an arbitrary Lagrangian-Eulerian multi-material finite element code used for modeling solid dynamics problems involving large distortion and shock propagation. This document describes the basic user input language and instructions for using the software.

An exploratory effort in the application of carbon epoxy composite structural materials to a multi-axis gimbal arm design is described. An existing design in aluminum was used as a baseline for a functionally equivalent redesigned outer gimbal arm using a carbon epoxy composite material. The existing arm was analyzed using finite element techniques to characterize performance in terms of strength, stiffness, and weight. A new design was virtually prototyped. using the same tools to produce a design with similar stiffness and strength, but reduced overall weight, than the original arm. The new design was prototyped using Rapid Prototyping technology, which was subsequently used to produce molds for fabricating the carbon epoxy composite parts. The design tools, process, and results are discussed.

Sensitivity analysis is critically important to numerous analysis algorithms, including large scale optimization, uncertainty quantification,reduced order modeling, and error estimation. Our research focused on developing tools, algorithms and standard interfaces to facilitate the implementation of sensitivity type analysis into existing code and equally important, the work was focused on ways to increase the visibility of sensitivity analysis. We attempt to accomplish the first objective through the development of hybrid automatic differentiation tools, standard linear algebra interfaces for numerical algorithms, time domain decomposition algorithms and two level Newton methods. We attempt to accomplish the second goal by presenting the results of several case studies in which direct sensitivities and adjoint methods have been effectively applied, in addition to an investigation of h-p adaptivity using adjoint based a posteriori error estimation. A mathematical overview is provided of direct sensitivities and adjoint methods for both steady state and transient simulations. Two case studies are presented to demonstrate the utility of these methods. A direct sensitivity method is implemented to solve a source inversion problem for steady state internal flows subject to convection diffusion. Real time performance is achieved using novel decomposition into offline and online calculations. Adjoint methods are used to reconstruct initial conditions of a contamination event in an external flow. We demonstrate an adjoint based transient solution. In addition, we investigated time domain decomposition algorithms in an attempt to improve the efficiency of transient simulations. Because derivative calculations are at the root of sensitivity calculations, we have developed hybrid automatic differentiation methods and implemented this approach for shape optimization for gas dynamics using the Euler equations. The hybrid automatic differentiation method was applied to a first order approximation of the Euler equations and used as a preconditioner. In comparison to other methods, the AD preconditioner showed better convergence behavior. Our ultimate target is to perform shape optimization and hp adaptivity using adjoint formulations in the Premo compressible fluid flow simulator. A mathematical formulation for mixed-level simulation algorithms has been developed where different physics interact at potentially different spatial resolutions in a single domain. To minimize the implementation effort, explicit solution methods can be considered, however, implicit methods are preferred if computational efficiency is of high priority. We present the use of a partial elimination nonlinear solver technique to solve these mixed level problems and show how these formulation are closely coupled to intrusive optimization approaches and sensitivity analyses. Production codes are typically not designed for sensitivity analysis or large scale optimization. The implementation of our optimization libraries into multiple production simulation codes in which each code has their own linear algebra interface becomes an intractable problem. In an attempt to streamline this task, we have developed a standard interface between the numerical algorithm (such as optimization) and the underlying linear algebra. These interfaces (TSFCore and TSFCoreNonlin) have been adopted by the Trilinos framework and the goal is to promote the use of these interfaces especially with new developments. Finally, an adjoint based a posteriori error estimator has been developed for discontinuous Galerkin discretization of Poisson's equation. The goal is to investigate other ways to leverage the adjoint calculations and we show how the convergence of the forward problem can be improved by adapting the grid using adjoint-based error estimates. Error estimation is usually conducted with continuous adjoints but if discrete adjoints are available it may be possible to reuse the discrete version for error estimation. We investigate the advantages and disadvantages of continuous and discrete adjoints through a simple example.

The purpose of the Sandia National Laboratories Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. The plan defines the ASC program software quality practices and provides mappings of these practices to Sandia Corporate Requirements CPR 1.3.2 and 1.3.6 and to a Department of Energy document, 'ASCI Software Quality Engineering: Goals, Principles, and Guidelines'. This document also identifies ASC management and software project teams responsibilities in implementing the software quality practices and in assessing progress towards achieving their software quality goals.

The purpose of the Sandia National Laboratories (SNL) Advanced Simulation and Computing (ASC) Software Quality Plan is to clearly identify the practices that are the basis for continually improving the quality of ASC software products. Quality is defined in DOE/AL Quality Criteria (QC-1) as conformance to customer requirements and expectations. This quality plan defines the ASC program software quality practices and provides mappings of these practices to the SNL Corporate Process Requirements (CPR 1.3.2 and CPR 1.3.6) and the Department of Energy (DOE) document, ASCI Software Quality Engineering: Goals, Principles, and Guidelines (GP&G). This quality plan identifies ASC management and software project teams' responsibilities for cost-effective software engineering quality practices. The SNL ASC Software Quality Plan establishes the signatories commitment to improving software products by applying cost-effective software engineering quality practices. This document explains the project teams opportunities for tailoring and implementing the practices; enumerates the practices that compose the development of SNL ASC's software products; and includes a sample assessment checklist that was developed based upon the practices in this document.

Macroscopic quantum states such as superconductors, Bose-Einstein condensates and superfluids are some of the most unusual states in nature. In this project, we proposed to design a semiconductor system with a 2D layer of electrons separated from a 2D layer of holes by a narrow (but high) barrier. Under certain conditions, the electrons would pair with the nearby holes and form excitons. At low temperature, these excitons could condense to a macroscopic quantum state either through a Bose-Einstein condensation (for weak exciton interactions) or a BCS transition to a superconductor (for strong exciton interactions). While the theoretical predictions have been around since the 1960's, experimental realization of electron-hole bilayer systems has been extremely difficult due to technical challenges. We identified four characteristics that if successfully incorporated into a device would give the best chances for excitonic condensation to be observed. These characteristics are closely spaced layers, low disorder, low density, and independent contacts to allow transport measurements. We demonstrated each of these characteristics separately, and then incorporated all of them into a single electron-hole bilayer device. The key to the sample design is using undoped GaAs/AlGaAs heterostructures processed in a field-effect transistor geometry. In such samples, the density of single 2D layers of electrons could be varied from an extremely low value of 2 x 10{sup 9} cm{sup -2} to high values of 3 x 10{sup 11} cm{sup -2}. The extreme low values of density that we achieved in single layer 2D electrons allowed us to make important contributions to the problem of the metal insulator transition in two dimensions, while at the same time provided a critical base for understanding low density 2D systems to be used in the electron-hole bilayer experiments. In this report, we describe the processing advances to fabricate single and double layer undoped samples, the low density results on single layers, and evidence for gateable undoped bilayers.

Abstract not provided.

The objective of this LDRD project was to develop a programmable diffraction grating fabricated in SUMMiT V{trademark}. Two types of grating elements (vertical and rotational) were designed and demonstrated. The vertical grating element utilized compound leveraged bending and the rotational grating element used vertical comb drive actuation. This work resulted in two technical advances and one patent application. Also a new optical configuration of the Polychromator was demonstrated. The new optical configuration improved the optical efficiency of the system without degrading any other aspect of the system. The new configuration also relaxes some constraint on the programmable diffraction grating.