Publications

A split Hopkinson bar technique has been developed to evaluate the performance of accelerometers that measure large amplitude pulses. An evaluation of this technique has been conducted in the Mechanical Shock Laboratory at Sandia National Laboratories (SNL) to determine its use in the practical calibration of accelerometers. This evaluation consisted of three tasks. First, the quartz crystal was evaluated in a split Hopkinson bar configuration to evaluate the quartz gage`s sensitivity and frequency response at force levels of 18,000, 35,000 and 53,000 N at ambient temperature, {minus}48 C and +74 C. Secondly, the fly away technique was evaluated at shock amplitudes of 50,000, 100,000, 150,000 and 200,000 G (1 G = 9.81 m/s{sup 2}) at ambient temperature, {minus}48 C and +74 C. Lastly, the technique was performed using a NIST calibrated reference accelerometer. Comparisons of accelerations calculated from the quartz gage data and the measured acceleration data have shown very good agreement. Based on this evaluation, the authors expect this split Hopkinson fly away technique to be certified by the SNL Primary Standards Laboratory.

Many dynamical systems tested in the field and the laboratory display significant nonlinear behavior. Accurate characterization of such systems requires modeling in a nonlinear framework. One construct forming a basis for nonlinear modeling is that of the artificial neural network (ANN). However, when system behavior is complex, the amount of data required to perform training can become unreasonable. The authors reduce the complexity of information present in system response measurements using decomposition via canonical variate analysis. They describe a method for decomposing system responses, then modeling the components with ANNs. A numerical example is presented, along with conclusions and recommendations.

Sandia National Laboratories and Tracor Applied Sciences have developed a proof-of-concept Expert System for the automatic detection and diagnosis of several important problems in geothermal drilling. The system is designed to detect loss of circulation, influx, loss of pump efficiency, and sensor problems. Data from flow sensors (including the rolling float meter), the pump stroke counter and other sensors are processed and examined for deviations from expected patterns. The deviations from expected patterns. The deviations are transformed into evidence for a Bayesian Network (a probabilistic reasoning tool), which estimates the probability of each fault. The results are displayed by a Graphical User Interface, which also allows the user to see data related to a specific fault. The prototype was tested on real data, and successfully detected and diagnosed faults.

This paper presents the results of tests performed on a variety of electrochemical microactuators and arrays of these actuators fabricated in the SUMMiT process at the U.S. Department of Energy`s Sandia National Laboratories. These results are intended to aid designers of thermally actuated mechanisms, and they apply to similar actuators made in other polysilicon MEMS processes such as the MUMPS process. Measurements include force and deflection versus input power, maximum operating frequency, effects of long term operation, and ideal actuator and array geometries for different applications` force requirements. Also, different methods of arraying these actuators together are compared. It is found that a method using rotary joints, enabled by the advanced features of the SUMMiT fabrication process, is the most efficient array design. The design and operation of a thermally actuated stepper motor is explained to illustrate a useful application of these arrays.

The response of a system containing an energetic material (EM) to an abnormal thermal environment is termed cookoff. To predict the violence of reaction of confined energetic materials during cookoff requires a description of the relevant physical processes that occur on time scales Ranging from days to submicroseconds. The time-to-ignition can be characterized accurately using heat transfer with chemistry and quasistatic mechanics. After ignition the energetic material deflagrates on a millisecond time scale. During this time the mechanical processes become dynamic. If the confinement survives burning then accelerated deflagration can lead to shock formation and deflagration to detonation transition. The focus of this work is the dynamic combustion regime in the millisecond time domain. Due to the mathematical stiffness of the chemistry equations and the prohibitively fine spatial resolution requirements needed to resolve the structure of the flame, an interface tracking approach is used to propagate the burn front. Demonstrative calculations are presented that illustrate the dynamic interaction of the deflagrating energetic material with its confinement.

A high consequence system is often defined as one in which the potential exists for severe or catastrophic accidents. Familiar examples include nuclear power plants, airline and other mass transportation, dams and reservoirs, and large-scale food processing. Many manufacturing systems also qualify as high consequence systems. Much of the authors` experience with high consequence systems derives from work associated with the surveillance and dismantlement of nuclear weapons for the US Department of Energy. With such operations, there exists a risk of high explosive detonation accompanied by radiological dispersal and, potentially, nuclear detonation. Analysis of major industrial accidents such as Three Mile Island, Chernobyl and Bhopal have revealed that these incidents were not attributable to a single event or direct cause, but were the result of multiple factors that combined to create a condition ripe for an accident. In each case, human error was a critical factor contributing to the accident. Consequently, many authors have emphasized the need for greater appreciation of systematic factors and in particular, human activities. This paper discusses approaches used in hazard analysis of US nuclear weapons operations to assess risk associated with human factors.

The authors report on an integrated program to understand the fundamentals of LiMn{sub 2}O{sub 4} performance as a cathode for lithium ion rechargeable batteries. Specifically, this program is designed to address the effects of doping on the crystal chemistry, lattice constants, and electrochemical performance. The work is being expanded to include studies on LiCoO{sub 2} and LiNiO{sub 2}.

The authors conducted experiments that monitored the response of heated, confined energetic materials in both fixed-volume and fixed-load configurations. They studied a variety of HMX-based materials, looking at the effects of particle size and binders. The {beta}-{delta} phase transition near 170 C led to a more reactive state. Materials that underwent complete transition in the fixed-load experiments (allowed to expand fully to accommodate the 5% volume increase) cooked off faster than those in the fixed-volume configuration.

International relations are often devoted to establishing agreements that define, control, or regulate issues of potential conflict or dispute. These agreements span a full range of national and international issues from human rights to resource allocations and national security. The scope of these agreements can vary from bilateral arrangements to global treaties or control regimes. In many cases, elements of the agreement are monitored to verify compliance or increase confidence among parties that the terms of the agreement are being met. This article outlines options for cooperation on the Korean peninsula that could build confidence and reduce tension. The role of monitoring technology in helping to implement such agreements is also described.

The Federal Aviation Administration`s Airworthiness Assurance NDI Validation Center (AANC) and the Center for Aviation Systems Reliability (CASR) are currently working to develop a liquid penetrant inspection (LPI) system evaluation capability that will support the needs of the penetrant manufacturers, commercial airline industry and the FAA. The main focus of this facility is to support the evaluation of penetrant inspection materials, penetrant systems and to apply resources to support industry needs. This paper discusses efforts to create such a facility and an initial project to produce fatigue crack specimens for evaluation of Type 1 penetrant sensitivities.

One role of the Intelligent Robotics and System Center (ISRC) at Sandia National Laboratories is to address certain aspects of Sandia`s mission to design, manufacture, maintain, and dismantle nuclear weapon components. Hazardous materials, devices, and environments are often involved. Because of shrinking resources, these tasks must be accomplished with a minimum of prototyping, while maintaining high reliability. In this paper, the authors describe simulation, off-line programming/planning, and related tools which are in use, under development, and being researched to solve these problems at the ISRC.

A technique is presented to simultaneously diffuse boron and phosphorus in silicon, and grow an in-situ passivating oxide in a single furnace step. It is shown that limited solid doping sources made from P and B Spin-On Dopant (SOD) films can produce optimal n{sup +} and p{sup +} profiles simultaneously without the deleterious effects of cross doping. A high quality passivating oxide is grown in-situ beneath the thin ({approximately} 60 {angstrom}) diffusion glass, resulting in low J{sub o} values below 100 fA/cm{sup 2} for transparent ({approximately} 100 {Omega}/{open_square}) phosphorus and boron diffusions. For the first time it is shown that impurities present in the boron SOD film can be effectively filtered out by employing separate source wafers, resulting in bulk lifetimes in excess of 1 ms for the sample wafers. The degree of lifetime degradation in the sources is related to the gettering efficiency of boron in silicon. This novel simultaneous diffusion, in-situ oxidation, impurity filtering and gettering technique was successfully used to produce 20.3% Fz, and 19.1% Cz solar cells, in one furnace step.

A survey of US system integrators, charge controller manufacturers, and battery manufacturers was conducted in 1996 to determine market and application trends. This survey was sponsored by the USDOE. Results from 21 system integrators show a 1995 PV battery sales of $4.76 million. Using the survey results, a top down market analysis was conducted with a total predicted US battery market of $34.7 million and a world wide market of US $302 million. The survey also indicated that 71% (of dollars) were spent on VRLA and 29% on flooded lead-acid batteries. Eighty percent of charge controllers were ON-OFF, vs. PWM or constant voltage.

The Department of Energy (DOE) national laboratories have one of the longest and most consistent histories of supercomputer use. The authors summarize the architecture of DOE`s new supercomputers that are being built for the Accelerated Strategic Computing Initiative (ASCI). The authors then argue that in the near future scaled-down versions of these supercomputers with petaflop-per-weekend capabilities could become widely available to hundreds of research and engineering departments. The availability of such computational resources will allow simulation of physical phenomena to become a full-fledged third branch of scientific exploration, along with theory and experimentation. They describe the ASCI and other supercomputer applications at Sandia National Laboratories, and discuss which lessons learned from Sandia`s long history of supercomputing can be applied in this new setting.

Composite doublers are gaining popularity for their ability to repair and reinforce commercial aircraft structures and it is anticipated that the potential cost savings may spur wider use of this technology. But before composite doublers can be accepted by the civil aviation industry, inspection techniques must be developed to verify the integrity of the doubler and the parent material under the doubler. The Federal Aviation Administration Airworthiness Assurance NDI Validation Center (AANC) is currently developing test methods to inspect aircraft structures under composite doublers using low kilovoltage radiography. This paper documents the radiographic techniques developed by the AANC which have been found to give the best contrast of the radiographic image with reduced image distortion.

In this report, a study of wave propagation and damping in a fluid loaded Flexural Plate Wave (FPW) sensor is presented. Previous to this study, it was believed that supersonic radiation was the dominate mechanism of loss in FPW devices. However, because no previous theory had been developed to explain finite length effects, this belief was never challenged. In this paper, it will be shown that the dominate mechanism of damping is not only due to supersonic radiation, but is also due to a fluid/structure resonance arising from finite length effects. The two-dimensional equations of motion for a single port FPW sensor plate are derived and coupled to the equations of motion for a viscous Newtonian fluid. These coupled equations are solved by using a wave number transform approach. This approach captures dynamics due to source terms at infinity. The resulting solution is comprised of terms derived by Wenzel, plus additional terms representing diffracted wave dynamics. The displacement field above the plate is then determined by using the Helmholtz integral equation.

In 1995, Salt River Project (SRP), a public power utility located in Phoenix, Arizona, collaborated with the Electric Power Research Institute (EPRI) and Sandia National Laboratories (Sandia) to initiate a photovoltaic (PV) power system with battery energy storage to match PV output with residential customer peak energy demand periods. The PV power system, a 2.4kW PV array with 25.2kWh of energy storage, was designed and installed by Southwest Technology Development Institute (SWTDI) at an SRP-owned facility, known as the Chandler Research House during August 1995. This paper presents an overview of the system design, operation and performance. 3 refs., 2 figs., 2 tabs.

The Ministry of the Russian Federation for Atomic Energy (MINATOM) and the US Department of Energy (DOE) are engaged in joint, cooperative efforts to reduce the likelihood of nuclear proliferation by enhancing Material Protection, Control and Accounting (MPC&A) systems in both countries. Mayak Production Association (MPA) is a major Russian nuclear enterprise within the nuclear complex that is operated by MINATOM. This paper describes the nature, scope, and status of the joint, cooperative efforts to enhance existing MPC&A systems at MPA. Current cooperative efforts are focused on enhancements to the existing MPC&A systems at four plants that are operated by MPA and that produce, process, handle and/or store proliferation-sensitive nuclear materials.

PV hybrid electric power systems can offer an economically competitive alternative to engine generator (genset) systems in many off-grid applications. Besides the obvious `green` advantages of producing less noise and emissions, the PV hybrid can, in some cases, offer a lower life-cycle cost (LCC) then the genset. This paper evaluates the LCC of the 9.6 kWp PV hybrid power system installed by the National Park Services (NPS) at Pinnacles National Monument, CA. NPS motivation for installation of this hybrid was not based on economics, but rather the need to replace two aging diesel gensets with an alternative that would be quieter, fuel efficient, and more in keeping with new NPS emphasis on sustainable design and operations. In fact, economic analysis shows a lower 20-year LCC for the installed PV hybrid than for simple replacement of the two gensets. The analysis projects are net savings by the PV hybrid system of $83,561 and over 162,000 gallons of propane when compared with the genset-only system. This net savings is independent of the costs associated with environmental emissions. The effects of including emissions costs, according to NPS guidelines, is also discussed. 5 refs., 2 figs., 3 tabs.

This document describes the results of the Comprehensive Test Ban Treaty (CTBT) Infrasound Prototype Development Test and Evaluation (DT&E). During DT&E the infrasound prototype was evaluated against requirements listed in the System Requirements Document (SRD) based on the Conference on Disarmament/Ad Hoc Committee on a Nuclear Test Ban/Working Papers 224 and 283 and the Preparatory Commission specifications as defined in CTBT/PC/II/1/Add.2, Appendix X, Table 5. The evaluation was conducted during a two-day period, August 6-7, 18997. The System Test Plan (STP) defined the plan and methods to test the infrasound prototype. Specific tests that were performed are detailed in the Test Procedures (TP).

The results of the investigation of retention and thermal desorption of hydrogen isotopes of B{sub 4}C coated RGT (a recrystallized graphite with high thermal conductivity, 600 W/mK) after the exposure to high heat flux in the divertor strike point region of DIII-D using the DiMES sample exchange system are reported. It is shown that the material is very promising for plasma facing elements of tokamaks.

Neutron reflection is used to examine the structure of an epoxy near an interface. Variations in both the density and the crosslink density within the interphase region are examined. The density is increased near the interface relative to that in the bulk of the film, but the crosslink density over the same region is reduced relative to that in the bulk of the film. These observations are interpreted via packing of the resin oligamers next to the wall, which leads to an increased density and also inhibits the crosslinking reaction. The effect is more pronounced the more slowly the resin is cured. Significant variations in reflectivity are observed with thermal cycling, which indicate an increase in the size of the interfacial layer of excess toluene. However, data for samples with greater number of thermal cycles are required to determine the relation of this effect to the fracture process.

SEMATECH was established in 1987 for defense and economic reasons to help the U.S. regain a competitive posture in semiconductor manufacturing. For 10 years SEMATECH was jointly funded by the federal government and semiconductor manufacturing companies representing 85 percent of the U.S. semiconductor industry. SEMATECH has spent about 80 percent of these funds on activities intended to produce useful results between 1 and 3 years. Very early in the establishment of SEMATECH, its members determined that their first priority would be to strengthen their U.S. based suppliers of semiconductor manufacturing equipment. This has been the primary thrust of SEMATECH. SEMATECH first held some 30 workshops on a broad set of technical topics to assess the needs and opportunities to help the industry recover. These workshops scoped manufacturing areas where SEMATECH should focus. These early meetings were an early form of what later came to be termed roadmapping. The scope of R&D needs identified in these workshops well exceeded what SEMATECH could hope to accomplish with its $200 million annual budget. Wayne Johnson of Sandia participated in five of these workshops and used the knowledge gained as the basis for proposals later submitted to SEMATECH on behalf of Sandia. In the fall of 1989 the SETEC program was established at Sandia to support SEMATECH. This was initially a funds-in, work-for-others project that was fully funded by SEMATECH. Thus, the early work was entirely focused on SEMATECH`s needs. Later in the program when SEMATECH funds were supplemented by Department of Energy Cooperative Research and Development funds, attention was given to how this project would benefit Sandia`s defense microelectronics program.

This paper presents an analysis of how the US government responded to the concern in the 1980`s that US companies were experiencing problems of competitiveness in international markets. By the mid 1980`s there was great and growing concern throughout the US that US companies were experiencing difficulties in international competition. Pressure on Congress to take action came from constituents seeking jobs and companies that would directly benefit (this usually means receive public money) from programs that Congress might initiate. The fact that most constituent calls to Congress were about job creation was lost in the on-rush of R&D performers seeking funds for their favorite R&D project. In response, Congress created the Advanced Technology Program, the Technology Transfer Initiative, and the Technology Reinvestment Project, expanded the responsibilities of ARPA/DARPA, increased funding for the Small Business Initiative, expanded the Manufacturing Extension Partnership, funded SEMATECH, and increased NSF funding for basic research at universities. Many of these programs were later criticized for being industrial welfare and several were cut-back or stopped. Retrospective analysis shows that few of these programs addressed the root cause of competitiveness difficulties. In fact, by the time most of these programs were in place, US companies were well on their way to correcting their competitiveness problems. In addition, few were relevant to companies` often expressed concerns about workforce training, regulatory costs, and access to foreign markets. Twenty percent reductions in health care costs, regulatory costs, and education costs could annually pump $500 billion into the US economy and make companies operating in the US much more competitive in international markets.

The papers in this Faraday Discussion represent the state-of-the-art in using acoustic devices to measure the properties of thin films and interfaces. Sauerbrey first showed that the mass sensitivity of a quartz crystal could be used to measure the thickness of vacuum-deposited metals. Since then, significant progress has been made in understanding other interaction mechanisms between acoustic devices and contacting media. Bruckenstein and Shay and Kanazawa and Gordon showed that quartz resonators could be operated in a fluid to measure surface mass accumulation and fluid properties. The increased understanding of interactions between acoustic devices and contacting media has allowed new information to be obtained about thin films and interfaces. These closing remarks will summarize the current state of using acoustic techniques to probe thin films and interfaces, describe the progress reported in this Faraday Discussion, and outline some remaining problems. Progress includes new measurement techniques, novel devices, new applications, and improved modeling and data analysis.