Publications

Abstract not provided.

We report on AlGaN HEMT-based logic development, using combined enhancement- and depletion-mode transistors to fabricate inverters with operation from room temperature up to 500°C. Our development approach included: (a) characterizing temperature dependent carrier transport for different AlGaN HEMT heterostructures, (b) developing a suitable gate metal scheme for use in high temperatures, and (c) over-temperature testing of discrete devices and inverters. Hall mobility data revealed the GaN-channel HEMT experienced a 6.9× reduction in mobility, whereas the AlGaN channel HEMTs experienced about a 3.1x reduction. Furthermore, a greater aluminum contrast between the barrier and channel enabled higher carrier densities in the two-dimensional electron gas for all temperatures. The combination of reduced variation in mobility with temperature and high sheet carrier concentration showed that an Al-rich AlGaN-channel HEMT with a high barrier-to-channel aluminum contrast is the best option for an extreme temperature HEMT design. Three gate metal stacks were selected for low resistivity, high melting point, low thermal expansion coefficient, and high expected barrier height. The impact of thermal cycling was examined through electrical characterization of samples measured before and after rapid thermal anneal. The 200 nm tungsten gate metallization was the top performer with minimal reduction in drain current, a slightly positive threshold voltage shift, and about an order of magnitude advantage over the other gates in on-to-off current ratio. After incorporating the tungsten gate metal stack in device fabrication, characterization of transistors and inverters from room temperature up to 500°C was performed. The enhancement-mode (e-mode) devices’ resistance started increasing at about 200°C, resulting in drain current degradation. This phenomenon was not observed in depletion-mode (d-mode) devices but highlights a challenge for inverters in an e-mode driver and d-mode load configuration.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Vertical gallium nitride (GaN) p-n diodes have garnered significant interest for use in power electronics where high-voltage blocking and high-power efficiency are of concern. In this article, we detail the growth and fabrication methods used to develop a large area (1 mm2) vertical GaN p-n diode capable of a 6.0-kV breakdown. We also demonstrate a large area diode with a forward pulsed current of 3.5 A, an 8.3-mΩ·cm2 differential specific ON-resistance, and a 5.3-kV reverse breakdown. In addition, we report on a smaller area diode (0.063 mm2) that is capable of 6.4-kV breakdown with a differential specific ON-resistance of 10.2 m·Ω·cm2, when accounting for current spreading through the drift region at a 45° angle. Finally, the demonstration of avalanche breakdown is shown for a 0.063-mm2 diode with a room temperature breakdown of 5.6 kV. These results were achieved via epitaxial growth of a 50-μm drift region with a very low carrier concentration of < 1×1015 cm-3 and a carefully designed four-zone junction termination extension.

Abstract not provided.

Abstract not provided.

The ability to form pristine interfaces after etching and regrowth of GaN is a prerequisite for epitaxial selective area doping, which in turn is needed for the formation of lateral PN junctions and advanced device architectures. In this work, we report the electrical properties of etched-and-regrown GaN PN diodes using an in situ Cl-based precursor, tertiary butylchloride (TBCl). We demonstrated a regrowth diode with I–V characteristics approaching that from a continuously grown reference diode. The sources of unintentional contamination from the silicon (Si) impurity and the mediating effect of Si during the TBCl etching are also investigated in this study. Furthermore, this work points to the potential of in situ TBCl etching toward the realization of GaN lateral PN junctions.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Ultra-low voltage drop tunnel junctions (TJs) were utilized to enable multi-active region blue light emitting diodes (LEDs) with up to three active regions in a single device. The multi-active region blue LEDs were grown monolithically by metal-organic chemical vapor deposition (MOCVD) without growth interruption. This is the first demonstration of a MOCVD grown triple-junction LED. Optimized TJ design enabled near-ideal voltage and EQE scaling close to the number of junctions. This work demonstrates that with proper TJ design, improvements in wall-plug efficiency at high output power operation are possible by cascading multiple III-nitride based LEDs.

Abstract not provided.

Abstract not provided.

Abstract not provided.

In this work, ultrawide bandgap Al_0.7Ga_0.3N MESFETs with refractory Tungsten Schottky and Ohmic contacts are studied in 300–675 K environments. Variable-temperature dc electrical transport reveals large ON-state drain current densities for an AlGaN device: 209 mA/mm at 300 K and 156 mA/mm at 675 K in the ON-state (25% reduction). Drain and gate currents are only weakly temperature-dependent, suggesting potential for engineering temperature invariant operation. The ON-/ OFF-ratio is limited by OFF-state leakage through the gate, which is attributed to damage from sputter deposition. Future work using refractory metals with larger work functions that are deposited by electron beam deposition is proposed.

Understanding the impact of high-energy electron radiation on device characteristics remains critical for the expanding use of semiconductor electronics in space-borne applications and other radiation harsh environments. Here, we report on in situ measurements of high-energy electron radiation effects on the hole diffusion length in low threading dislocation density homoepitaxial bulk n-GaN Schottky diodes using electron beam induced current (EBIC) in high-voltage scanning electron microscopy mode. Despite the large interaction volume in this system, quantitative EBIC imaging is possible due to the sustained collimation of the incident electron beam. This approach enables direct measurement of electron radiation effects without having to thin the specimen. Using a combination of experimental EBIC measurements and Monte Carlo simulations of electron trajectories, we determine a hole diffusion length of 264 ± 11 nm for n-GaN. Irradiation with 200 kV electron beam with an accumulated dose of 24 × 1016 electrons cm−2 led to an approximate 35% decrease in the minority carrier diffusion length.

Advanced GaN power devices are promising for many applications in high power electronics but performance limitations due to material quality in etched-and-regrown junctions prevent their widespread use. Carrier diffusion length is a critical parameter that not only determines device performance but is also a diagnostic of material quality. Here we present the use of electron-beam induced current to measure carrier diffusion lengths in continuously grown and etched-and-regrown GaN pin diodes as models for interfaces in more complex devices. Variations in the quality of the etched-and-regrown junctions are observed and shown to be due to the degradation of the n-type material. We observe an etched-and-regrown junction with properties comparable to a continuously grown junction.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We carefully investigate three important effects including postgrowth activation annealing, delta (δ) dose and magnesium (Mg) buildup delay as well as experimentally demonstrate their influence on the electrical properties of GaN homojunction p–n diodes with a tunnel junction (TJ). The diodes were monolithically grown by metalorganic chemical vapor deposition (MOCVD) in a single growth step. By optimizing the annealing parameters for Mg activation, δ-dose for both donors and acceptors at TJ interfaces, and p+-GaN layer thickness, a significant improvement in tunneling properties is achieved. For the TJs embedded within the continuously-grown, all-MOCVD GaN diode structures, ultra-low voltage penalties of 158 mV and 490 mV are obtained at current densities of 20 A cm−2 and 100 A cm−2, respectively. The diodes with the engineered TJs show a record-low differential resistivity of 1.6 × 10−4 Ω cm2 at 5 kA cm−2.