The sorption of Cs and Cd on model soil minerals was examined by complementary analytical and experimental procedures. X-ray photoelectron spectroscopy (XPS) and nuclear magnetic resonance (NMR) spectroscopy were used to characterize the chemical and physical nature of Cs-reacted soil minerals. Cd and Cs adsorption isotherms for kaolinite were also measured at variable pH and temperature to establish likely reaction stoichiometries, while atomic force microscopy (AFM) was used to characterize the microtopography of the clay surface. XPS analyses of Cs-exchanged samples show that Cs is sorbed at mineral surfaces and at the interlayer site of smectite clays, although the spectral resolution of XPS analyses is insufficient to differentiate between basal, edge or interlayer sites. {sup 133}Cs MAS-NMR results also show that Cs is adsorbed primarily in an interlayer site of montmorillonite and on edge and basal sites for kaolinite. Cd adsorption isotherms on kaolinite were found to be additive using Al{sub 2}0{sub 3} + Si0{sub 2} Cd binding constants. AFM quantification of kaolinite crystallites suggest that edges comprise up to 50% of the BET surface area, and are consistent with NMR and surface charge results that Cs an Cd adsorption occur primarily at edge sites.
Sandia National Laboratories has worked with Synthetica Technologies and Manufacturing and Technology Conversion International (MTCl) to demonstrate the applicability of their commercial steam reforming technologies for treating DOE low-level mixed wastes. Previously, Synthetica successfully demonstrated destruction of a Sandia formulated lab trash simulant. During November 1994 Synthetica did not adequately process the aqueous halogenated organic liquid mixed waste simulant (MWTP-2110) formulated by the DOE Mixed Waste Integrated Program (MWIP). Testing at MTCl is ongoing and initial results appear to be favorable. Approximately 200 lbs each of the MWIP aqueous halogenated organic liquids (MWTP-2110), and absorbed aqueous and organic liquids (MWTP-3113/3114) simulants have been processed. At 1650{degree}F, destruction efficiencies of greater than 99% were obtained for tetrachloroethylene, toluene, and 1,2 dichlorobenzene. Product cases consisted primarily of H{sub 2}, C0{sub 2}, CO, and CH{sub 4} and had higher heating values of up to 355 BTU/SCF. Conclusions concerning the suitability of the MTCI process for treating DOE mixed wastes will be drawn upon the completion of testing.
Public concerns about surface water quality and its impact on health issues have put a premium on the ability to predict surface and groundwater quality in urban areas. The movement of toxins and nutrients in urban areas is largely controlled by interactions with soil and aquifer minerals along hydrologic pathways. Despite progress in theoretical modeling of the effects of these interactions on water chemistry, it is presently impossible to predict overall trends in urban water quality. Determining the controls on stream water chemistry is problematic due to the interplay between different hydrologic reservoirs which cannot be easily observed or measured. Natural tracers, such as dissolved ions and isotopes, provide an indirect method for observing subsurface interactions and are useful for time series analysis of stream water composition. Ionic species are generally nonconservative components because of chemical reactions and are thus useful for discerning the overall discharge chemistry affected by the relationship.
The primary purpose of this paper is to provide a careful evaluation of the diffusion velocity concept with regard to its ability to predict the diffusion of vorticity near a moving wall. A computer code BDIF has been written which simulates the evolution of the vorticity field near a wall of infinite length which is moving in an arbitrary fashion. The simulations generated by this code are found to give excellent results when compared to several exact solutions. We also outline a two-dimensional unsteady viscous boundary layer model which utilizes the diffusion velocity concept and is compatible with vortex methods. A primary goal of this boundary layer model is to minimize the number of vortices generated on the surface at each time step while achieving good resolution of the vorticity field near the wall. Preliminary results have been obtained for simulating a simple two-dimensional laminar boundary layer.
Sol-gel processing has been widely used in the preparation of lead zirconate titanate (PZT) thin films. The authors have applied this methodology to the formation of lead magnesium niobate (PMN) spin-cast deposited thin films. Since there is a limited number of soluble, commercially available compounds, the authors have recently synthesized a series of novel metal alkoxides for use as precursors for generation of PMN thin films and powders. The process for generation of the perovskite phase of these PMN powders and films are reported.
The numerical code TOUGH2 was used to assess alternative conceptual models of fracture flow. The models that were considered included the equivalent continuum model (ECM) and the dual permeability (DK) model. A one-dimensional, layered, unsaturated domain was studied with a saturated bottom boundary and a constant infiltration at the top boundary. Two different infiltration rates were used in the studies. In addition, the connection areas between the fracture and matrix elements in the dual permeability model were varied. Results showed that the two conceptual models of fracture flow produced different saturation and velocity profiles-even under steady-state conditions. The magnitudes of the discrepancies were sensitive to two parameters that affected the flux between the fractures and matrix in the dual permeability model: (1) the fracture-matrix connection areas and (2) the capillary pressure gradients between the fracture and matrix elements.
This paper discusses, in a general way, the influence of technology on the economy. The target audience is engineers who are involved in technology development but who are not especially familiar with economics. The measure used for describing the health of an economy is productivity. The impact of technological developments on productivity is discussed.
Hazardous materials management includes interactions among materials, personnel, facilities, hazards, and processes of various groups within a DOE site`s environmental, safety & health (ES&H) and line organizations. Although each group is charged with addressing a particular aspect of these properties and interactions, the information it requires must be gathered into a coherent set of common data for accurate and consistent hazardous material management and regulatory reporting. It is these common data requirements which the Cradle-to-Grave Tracking and Information System (CGTIS) is designed to satisfy. CGTIS collects information at the point at which a process begins or a material enters a facility, and maintains that information, for hazards management and regulatory reporting, throughout the entire life-cycle by providing direct on-line links to a site`s multitude of data bases to bring information together into one common data model.
The RADTRAN computer code for transportation risk analysis, which has been under continuous development at Sandia National Laboratories since 1977, has evolved from a purely research tool into a publicly available with a variety of applications. This expansion of the user community has substantially increased the need to make the system easier to use without decreasing its capabilities or the quality of output. A large set of modifiable RADTRAN input files has been available via TRANSNET for several years. One approach to assisting the user involves adding annotations/information to each of these files. A second approach is providing additional help in building new/modifying old input files. Keeping the proposed information/annotation files separate from but closely coupled to the modifiable input files within the TRANSNET shell system allows the modifiable input files to remain as regular input files while providing rapid, automatic access to, useful information about the analysis. In this way, the sample input files remain intact as regular RADTRAN input files and any files generated using associated on-line menus or editors may be readily converted into new input files. A single sample file is selected and used as an example to illustrate the prototype help features.
Scenario development for the system performance assessment of the Yucca Mountain Site Characterization Project defines a scenario as a well-posed problem connecting an initiating event with radionuclide release to the accessible environment by a logical and physically possible combination or sequence of features, events, and processes. Drawing on the advice and assistance of the Project`s principal investigators (PIs), a collection of release scenarios initiated by the nominal ground-water flow occurring in the vicinity of the potential Yucca Mountain high-level-waste repository is developed and described in pictorial form. This collection of scenarios is intended to provide a framework to assist PIs in recognizing essential field and calculational analyses, to assist performance assessment in providing guidance to site characterization, and to continue the effort to exhaustively identify all features, events, and processes important to releases. It represents a step in the iterative process of identifying what details of the potential site are important for safe disposal. 67 refs.
Correct operation of an information system requires a balance of ``surety`` domains -- access control (confidentiality), integrity, utility, availability, and safety. However, traditional approaches provide little help on how to systematically analyze and balance the combined impact of surety requirements on a system. The key to achieving information system surety is identifying, prioritizing, and mitigating the sources of risk that may lead to system failure. Consequently, the authors propose a risk assessment methodology that provides a framework to guide the analyst in identifying and prioritizing sources of risk and selecting mitigation techniques. The framework leads the analyst to develop a risk-based system model for balancing the surety requirements and quantifying the effectiveness and combined impact of the mitigation techniques. Such a model allows the information system designer to make informed trade-offs based on the most effective risk-reduction measures.
The agile manufacturing paradigm engenders many new concepts and work approaches for manufacturing operations. A technology often invoked in the concept of agility is modeling and simulation. Few would disagree that modeling and simulation holds the potential to substantially reduce the product development cycle and lead to improve product reliability and performance. Advanced engineering simulation can impact manufacturing in three areas: process design, product design, and process control. However, despite that promise, the routine utilization of modeling and simulation by industry within the design process is very limited. Advanced simulation is still used primarily in a troubleshooting mode examining design or process problems after the fact. Sandia National Laboratories has been engaged in the development of advanced engineering simulation tools for many years and more recently has begun to focus on the application of such models to manufacturing processes important for the defense industry. These efforts involve considerable interaction and cooperative research with US industry. Based upon this experience, this presentation examines the elements that are necessary for advanced engineering simulation to become an integral part of the design process.
This paper presents experimental data and computational modeling for a well-defined glass material. The experimental data cover a wide range of strains, strain rates, and pressures that are obtained from quasi-static compression and tension tests, split Hopkinson pressure bar compression tests, explosively driven flyer plate impact tests, and depth of penetration ballistic tests. The test data are used to obtain constitutive model constants for the improved Johnson-Holmquist (JH-2) brittle material model. The model and constants are then used to perform computations of the various tests.
At Sandia National Laboratories in Albuquerque, the author designed and fabricated a precision wire feeder to be used with high energy density (electron beam and laser beam) welding for weld joints where filler wire might be needed to fill a gap or to adjust the chemical composition so that a crack-free weld could be made. The wire feeder incorporates a 25,000 step-per-revolution motor to power a urethane-coated drive roll. A microprocessor-based controller provides precise control of the motor and allows both continuous and pulsed feeding of the wire. A unidirectional 0.75-in.-dia ball bearing is used to press the wire against the drive roll. A slight constant backward tension is maintained on the wire spool by a Bodine torque motor. A Teflon tube is used to guide the wire from the drive roll to the vicinity of the weld, where a hypodermic needle is used to aim the wire into the weld pool. The operation of the wire feeder was demonstrated by feeding a 10-mil-dia, Type 304 stainless steel wire into a variety of CO{sub 2} laser beam welds. The resulting welds are smooth and continuous, and the welds are considered to be completely satisfactory for a variety of applications.
Several government agencies and industrial sectors have recognized the need for, and payoff of, investing in the methodologies and associated technologies for improving the product realization process. Within the defense community as well as commercial industry, there are three major needs. First, they must reduce the cost of military products, of related manufacturing processes, and of the enterprises that have to be maintained. Second, they must reduce the time required to realize products while still applying the latest technologies. Finally, they must improve the predictability of process attributes, product performance, cost, schedule and quality. They must continue to advance technology, quickly incorporate their innovations in new products and in processes to produce them, and they need to capitalize on the raw computational power and communications bandwidth that continues to become available at decreasing cost. Sandia National Laboratories initiative is pursuing several interrelated, key concepts and technologies in order to enable such product realization process improvements: model-based design; intelligent manufacturing processes; rapid virtual and physical prototyping; and agile people/enterprises. While progress in each of these areas is necessary, this paper only addresses a portion of the overall initiative. First a vision of a desired future capability in model-based design and virtual prototyping is presented. This is followed by a discussion of two specific activities parametric design analysis of Synthetic Aperture Radars (SARs) and virtual prototyping of miniaturized high-density electronics -- that exemplify the vision as well as provide a status report on relevant work in progress.
One of the tasks of the Lethality Group within US Army Space and Strategic Defense Command (USASSDC) is the development of a capability to simulate various missile intercept scenarios using computer codes. Currently under development within USASSDC and its various contractor organizations is a group of codes collected under a master code called PEGEM for Post Event Ground Effects Model. Among the various components of the code are modules which are used to predict atmospheric dispersion and transport of particles or droplets following release at the altitude specified in the missile intercept scenario. The atmospheric transport code takes into account various source term data from the intercept such as: initial cloud size; droplet or particle size distribution; and, total mass of agent released. An ongoing USASSDC experimental program termed Crystal Mist involved release of precision glass beads under various altitude and meteorological conditions to assist in validation and refinement of various codes that are components of PEGEM used to predict particle atmospheric transport and diffusion following a missile intercept. Here, soda-lime glass beads used in the Crystal Mist series of atmospheric transport and diffusion tests were characterized by scanning electron microscopy and automated image processing routines in order to fully define their size distributions and morphology. Four bead size classifications ranging from a median count diameter of 45 to 200 micrometers were found to be approximately spherical and to fall within the supplier`s sizing specifications. Log-normal functions fit to the measured size distributions resulted in geometric standard deviations ranging from 1.08 to 1.12, thereby fulfilling the field trial requirements for a relatively narrow bead size distribution.
A novel, folded compact range configuration has been developed at the Sandia National Laboratories compact range antenna and radar cross section measurement facility, operated by the Radar/Antenna Department 2343, as a means of performing indoor, environmentally-controlled, far-field simulations of synthetic aperture radar (SAR) coherent change detection (CCD) measurements. This report describes the development of the folded compact range configuration, as well as the initial set of coherent change detection measurements made with the system. These measurements have been highly successful, and have demonstrated the viability of the folded compact range concept in simulating SAR CCD measurements. It is felt that follow-on measurements have the potential of contributing significantly to the body of knowledge available to the scientific community involved in CCD image generation and processing, and that this tool will be a significant aid in the research and development of change detection methodologies.
This report summarizes a number of research efforts completed over the past 20 years in the El Paso del Norte region to characterize pollution sources and air quality trends. The El Paso del Norte region encompasses the cities of El Paso, Texas and Ciudad Juarez, Chihuahua and is representative of many US-Mexico border communities that are facing important air quality issues as population growth and industrialization of Mexican border communities continue. Special attention is given to a group of studies carried out under special US Congressional funding and administered by the US Environmental Protection Agency. Many of these studies were fielded within the last several years to develop a better understanding of air pollution sources and trends in this typical border community. Summary findings from a wide range of studies dealing with such issues as the temporal and spatial distribution of pollutants and pollution potential from both stationary and mobile sources in both cities are presented. Particular emphasis is given to a recent study in El Paso-Ciudad Juarez that focussed on winter season PM{sub 10} pollution in El Paso-Ciudad Juarez. Preliminary estimates from this short-term study reveal that biomass combustion products and crustal material are significant components of winter season PM{sub 10} in this international border community.
This report summarizes the activities of a Lab Directed Research and Development (LDRD) Project to investigate the viability of asynchronous transfer mode (ATM) switching technology in the local area network (LAN) environment. A number of ATM based LANs were constructed and their performance capabilities were measured. The summary report notes the measurements and lessons learned from the two-year effort.
In today`s world, accurate finite-element simulations of large nonlinear systems may require meshes composed of hundreds of thousands of degrees of freedom. Even with today`s fast computers and the promise of ever-faster ones in the future, central processing unit (CPU) expenditures for such problems could be measured in days. Many contemporary engineering problems, such as those found in risk assessment, probabilistic structural analysis, and structural design optimization, cannot tolerate the cost or turnaround time for such CPU-intensive analyses, because these applications require a large number of cases to be run with different inputs. For many risk assessment applications, analysts would prefer running times to be measurable in minutes. There is therefore a need for approximation methods which can solve such problems far more efficiently than the very detailed methods and yet maintain an acceptable degree of accuracy. For this purpose, we have been working on two methods of approximation: neural networks and spring-mass models. This paper presents our work and results to date for spring-mass modeling and analysis, since we are further along in this area than in the neural network formulation. It describes the physical and numerical models contained in a code we developed called STRESS, which stands for ``Spring-mass Transient Response Evaluation for structural Systems``. The paper also presents results for a demonstration problem, and compares these with results obtained for the same problem using PRONTO3D, a state-of-the-art finite element code which was also developed at Sandia.
Traditional approaches to the assessment of information systems have treated system security, system reliability, data integrity, and application functionality as separate disciplines. However, each areas requirements and solutions have a profound impact on the successful implementation of the other areas. A better approach is to assess the ``surety`` of an information system, which is defined as ensuring the ``correct`` operation of an information system by incorporating appropriate levels of safety, functionality, confidentiality, availability, and integrity. Information surety examines the combined impact of design alternatives on all of these areas. We propose a modelling approach that combines aspects of fault trees and influence diagrams for assessing information surety requirements under a risk assessment framework. This approach allows tradeoffs to be based on quantitative importance measures such as risk reduction while maintaining the modelling flexibility of the influence diagram paradigm. This paper presents an overview of the modelling method and a sample application problem.
A thermomechanical analysis of a continuous fiber metal matrix composite (MMC) subjected to cyclic loading is performed herein. The analysis includes the effects of processing induced residual thermal stresses, matrix inelasticity, and interface cracking. Due to these complexities, the analysis is performed computationally using the finite element method. Matrix inelasticity is modelled with a rate dependent viscoplasticity model. Interface fracture is modelled by the use of a nonlinear interface constitutive model. The problem formulation is summarized, and results are given for a four-ply unidirectional SCS-6/{beta}21S titanium composite under high temperature isothermal mechanical fatigue. Results indicate rate dependent viscoplasticity can be a significant mechanism for dissipating the energy available for damage propagation, thus contributing to improved ductility of the composite. Results also indicate that the model may be useful for inclusion in life prediction methodologies for MMC`s.
In this paper a brief description of dynamic techniques commonly available for determining material property studies is presented. For many impact applications, the material generally experiences a complex loading path. In most cases, the initial loading conditions can be represented by the shock commonly referred to as the Hugoniot state. Subsequent loading or release structure, i.e., off-Hugoniot states would however be dependent on the physical processes dominating the material behavior. The credibility of the material model is tested by the accuracy of predictions of off-Hugoniot states. Experimental techniques commonly used to determine off-Hugoniot states are discussed in this survey.
There has been some concern that, as nuclear power plants age, protective measures taken to control and minimize the impact of fire may become ineffective, or significantly less effective, and hence result in an increased fire risk. One objective of the Fire Vulnerability of Aged Electrical Components Program is to assess the effects of aging and service wear on the fire vulnerability of electrical equipment. An increased fire vulnerability of components may lead to an overall increase in fire risk to the plant. Because of their widespread use in various electrical safety systems, electromechanical relays were chosen to be the initial components for evaluation. This test program assessed the impact of operational and thermal aging on the vulnerability of these relays to fire-induced damage. Only thermal effects of a fire were examined in this test program. The impact of smoke, corrosive materials, or fire suppression effects on relay performance were not addressed in this test program. The purpose of this test program was to assess whether the fire vulnerability of electrical relays increased with aging. The sequence followed for the test program was to: identify specific relay types, develop three fire scenarios, artificially age several relays, test the unaged and aged relays in the fire exposure scenarios, and compare the results. The relays tested were Agastat GPI, General Electric (GE) HMA, HGA, and HFA. At least two relays of each type were artificially aged and at least two relays of each type were new. Relays were operationally aged by cycling the relay under rated load for 2,000 operations. These relays were then thermally aged for 60 days with their coil energized.
An approach is described for performing scoping calculations of radionuclide release fractions from target materials being considered for use in the Accelerator Production of Tritium (APT) project, and some illustrative results are presented. The releases are evaluated for postulated accident scenarios involving severe overheating of either of two neutron source target materials, tungsten and lead. The potential for vaporization of radionuclides produced by spallation and neutron capture reactions is evaluated using a model that includes production of volatile species by reaction with steam, hydrogen, and/or oxygen. Emphasis is on release from the neutron source materials themselves, with a more limited treatment being given for radionuclides produced in other parts of the target/blanket assemblies. In the tungsten neutron source target, the low rate of diffusion within the tungsten is shown to limit releases of even volatile species to small values in a chemically inert or reducing environment. However, oxidative ablation of tungsten could permit considerably larger releases of volatile species in steam-rich or oxygen-rich environments. Tungsten radionuclides would dominate the source term for accident conditions considered the most plausible. For the lead neutron source target, the releases are predicted to be dominated by mercury radionuclides. Quantitative source term evaluation for this target is complicated because, in any accident sufficiently severe to be of much concern, lead melting will likely result in loss of target geometry. Hence, results presented for release from the lead must be carefully qualified. Extensive parametric results are presented for release from both neutron source materials. These results may be used to perform scoping estimates of radionuclide releases for additional APT accident scenarios as the controlling parameters for these scenarios become better defined.