Publications

Results 96926–96950 of 100,993

Search results

Jump to search filters

Frictional sliding in layered rock: Preliminary experiments on stacked Lexan plates

Perry Jr., K.E.; Epstein, J.S.; Jung, J.

Understanding the mechanical behavior of jointed-rock masses is of critical importance to designing and predicting the performance of a potential nuclear waste repositiry. To this end we have studied the frictional sliding between simulated rock joints using phase shifting moire interferometry. Preliminary calibration models were made from stacks of Lexan plates that were sand-blasted to provide a uniform frictional interface. Load was applied monotonically and phase shifted moire fringe patterns were recorded at three different load states. Plots of slip along the interfaces for the model are presented to demonstrate the ability of the photomechanics technique to provide precise measurements of in-plane displacement, and ultimately the slip between the plates.

More Details

Showmaker-Levy 9 and plume-forming collisions on Earth

Boslough, Mark

Computational models for the July, 1994 collision of comet Shoemaker-Levy 9 with Jupiter have provided a framework for interpreting the observational data. Imaging, photometry, and spectroscopy data from ground-based, Hubble Space Telescope, and Galileo spacecraft instruments are consistent with phenomena that were dominated by the generation of incandescent fireballs that were ballistically ejected to high altitudes, where they formed plumes that subsequently collapsed over large areas of Jupiter`s atmosphere. Applications of similar computational models to collisions into Earth`s atmosphere show that a very similar sequence of events should take place for NEO impacts with energies as low as 3 megatons, recurring on 100 year timescales or less. This result suggests that the 1908 Tunguska event was a plume-forming atmospheric explosion, and that some of the phenomena associated with it might be related to the ejection and collapse of a high plume. Hazards associated with plume growth and collapse should be included in the evaluation of the impact threat to Earth, and opportunities should be sought for observational validation of atmospheric impact models by exploiting data already being collected from the natural flux of multi-kiloton to megaton sized objects that constantly enter Earth`s atmosphere on annual to decadal timescales.

More Details

Comet Shoemaker-Levy 9 fragment size estimates: How big was the parent body?

Crawford, David A.

The impact of Comet Shoemaker-Levy 9 on Jupiter in July, 1994, was the largest, most energetic impact event on a planet ever witnessed. Because it broke up during a close encounter with Jupiter in 1992, it was bright enough to be discovered more than a year prior to impact, allowing the scientific community an unprecedented opportunity to assess the effects such an event would have. Many excellent observations were made from Earth-based telescopes, the Hubble Space Telescope (HST) and the Galileo spacecraft en route to Jupiter. In this paper, these observations are used in conjunction with computational simulations performed with the CTH shock-physics hydrocode to determine the sizes of the fifteen fragments that made discernible impact features on the planet. To do this, CTH was equipped with a radiative ablation model and a post-processing radiative ray-trace capability that enabled light-flux predictions (often called the impact flash) for the viewing geometries of Galileo and ground-based observers. The five events recorded by Galileo were calibrated to give fragment size estimates. Compared against ground-based and HST observations, these estimates were extended using a least-squares analysis to assess the impacts of the remaining ten fragments. Some of the largest impacts (L, G and K) were greater that 1 km in diameter but the density of the fragments was low, about 0.25 g/cm{sup 3}. The volume of the combined fifteen fragments would make a sphere 1.8 km in diameter. Assuming a pre-breakup density of 0.5 g/cm{sup 3}, the parent body of Shoemaker-Levy 9 had a probable diameter of 1.4 km. The total kinetic energy of all the impacts was equivalent to the explosive yield of 300 Gigatons of TNT.

More Details

Requirements for signaling channel authentication

Tarman, Thomas D.

This contribution addresses requirements for ATM signaling channel authentication. Signaling channel authentication is an ATM security service that binds an ATM signaling message to its source. By creating this binding, the message recipient, and even a third party, can confidently verify that the message originated from its claimed source. This provides a useful mechanism to mitigate a number of threats. For example, a denial of service attack which attempts to tear-down an active connection by surreptitiously injecting RELEASE or DROP PARTY messages could be easily thwarted when authenticity assurances are in place for the signaling channel. Signaling channel authentication could also be used to provide the required auditing information for accurate billing which is impervious to repudiation. Finally, depending on the signaling channel authentication mechanism, end-to-end integrity of the message (or at least part of it) can be provided. None of these capabilities exist in the current specifications.

More Details

Invariant patterns in crystal lattices: Implications for protein folding algorithms

Hart, William E.

Crystal lattices are infinite periodic graphs that occur naturally in a variety of geometries and which are of fundamental importance in polymer science. Discrete models of protein folding use crystal lattices to define the space of protein conformations. Because various crystal lattices provide discretizations of the same physical phenomenon, it is reasonable to expect that there will exist ``invariants`` across lattices that define fundamental properties of protein folding process; an invariant defines a property that transcends particular lattice formulations. This paper identifies two classes of invariants, defined in terms of sublattices that are related to the design of algorithms for the structure prediction problem. The first class of invariants is, used to define a master approximation algorithm for which provable performance guarantees exist. This algorithm can be applied to generalizations of the hydrophobic-hydrophilic model that have lattices other than the cubic lattice, including most of the crystal lattices commonly used in protein folding lattice models. The second class of invariants applies to a related lattice model. Using these invariants, we show that for this model the structure prediction problem is intractable across a variety of three-dimensional lattices. It`` turns out that these two classes of invariants are respectively sublattices of the two- and three-dimensional square lattice. As the square lattices are the standard lattices used in empirical protein folding` studies, our results provide a rigorous confirmation of the ability of these lattices to provide insight into biological phenomenon. Our results are the first in the literature that identify algorithmic paradigms for the protein structure prediction problem which transcend particular lattice formulations.

More Details

The use of low energy, ion induced nuclear reactions for proton radiotherapy applications

Nuclear Inst. and Methods in Physics Research, B

Horn, Kevin M.

Medical radiotherapy has traditionally relied upon the use of external photon beams and internally implanted radioisotopes as the chief means of irradiating tumors. However, advances in accelerator technology and the exploitation of novel means of producing radiation may provide useful alternatives to some current modes of medical radiation delivery - with reduced total dose to surrounding healthy tissue, reduced expense, or increased treatment accessibility. This paper will briefly overview currently established modes of radiation therapy, techniques still considered experimental but in clinical use and innovative concepts under study that may enable new forms of treatment or enhance existing ones. The potential role of low energy, ion-induced nuclear reactions in radiotherapy applications is examined specifically for the 650 keV d(3He,p)4 He nuclear reaction. This examination will describe the basic physics associated with this reaction's production of 17.4 MeV protons and the processes used to fabricate the necessary materials used in the technique. Calculations of the delivered radiation dose, heat generation, and required exposure times are presented. Experimental data is also presented validating the dose calculations. The design of small, lower cost ion accelerators, as embodied in "nested"-tandem and radio frequency quadrupole accelerators is examined, as is the potential use of high-output 3He and deuterium ion sources. Finally, potential clinical applications are discussed in terms of the advantages and disadvantages of this technique with respect to current radiotherapy methods and equipment. © 1995.

More Details

Determination of Buildup Factors in Titanium and Depleted Uranium

Seager, Kevin D.

Approximately 13% by volume of the US Department of Energy (DOE) current backlog of radioactive waste is characterized as high-level waste. Transportation of these wastes requires that the waste package have adequate shielding against gamma radiation. This project investigates the radiation shielding performance of titanium and depleted uranium, which have been proposed for use as gamma shielding materials in DOE transportation packages, by experimentally determining their buildup factors. Buildup factors are important in shield heating and radiation damage calculations. A point-isotropic-source type of buildup factor is the most useful for application in the point-kernal approach utilized in many simple shielding codes. The point-kernal method provides reasonable results for cases in which the shield is made of one solid material and the source can be approximated as one homogeneous material. The point-kernal method has been incorporated into a large number of shielding codes treating three-dimensional geometry using buildup factor data in some form. Buildup factors vary with a number of parameters such as the distance of penetration through the attenuating medium; the geometric configuration of the attenuating medium, source and detector position; the composition of the medium; the detector response function; and the energy and direction of emission of the source photons, ideally taken to be monoenergetic and isotropic.

More Details

What Should "Damaged" Mean in Air Transport of Fissile Packages?

Luna, Robert E.

It is likely that the ongoing process to produce the 1996 version of the IAEA Regulation for the Safe Transport of Radioactive Materials, IAEA Safety Series 6(SS 6) will result in a more stringent package qualification standard for air transport of large quantities of radioactive materials (RAM) than is included in the 1990 version. During the process to define the scope of the new requirements there was extensive discussion of their impact on, and application to, fissile material package qualification criteria. Since fissile materials are shipped in a variety of packaging ranging from exempt to Type B, each packaging of each type must be evaluated for its ability to maintain subcriticality both alone and in arrays and in both damaged and undamaged condition. In the 1990 version of SS 6 "damaged" means the condition of a package after it had undergone the "tests for demonstrating the ability to withstand accident conditions in transport," i.e., Type B qualification tests. These tests conditions are typical of severe accidents in surface modes but are less severe than air mode qualification test environments to be applied to Type C packages. As a result, questions arose about the need for a corresponding change in the 1996 SS 6 to define "damaged" to include the Type C test regime for criticality evaluations of fissile packages in air transport.

More Details

Pulsed ion beam surface treatment for preparing rapidly solidified corrosion resistant steel and aluminum surfaces

TMS Annual Meeting

Buchheit, R.G.; Maestas, L.M.; Mcintyre, D.C.; Stinnett, R.W.; Greenly, J.B.

Intense, pulsed ion beams were used to melt and rapidly resolidify Types 316F, 316L and sensitized 304 stainless steel surfaces to eliminate the negative effects of microstructural heterogeneity on localized corrosion resistance. Anodic polarization curves determined for 316F and 316L showed that passive current densities were reduced and pitting potentials were increased due to ion beam treatment. Type 304 samples sensitized at 600°C for 100 h showed no evidence of grain boundary attack when surfaces were ion beam treated. Equivalent ion beam treatments were conducted with a 6061-T6 aluminum alloy. Electrochemical impedance experiments conducted with this alloy exposed to an aerated chloride solution showed that the onset of pitting was delayed compared to untreated control samples.

More Details

Chromate-free corrosion resistant conversion coatings for aluminum alloys

TMS Annual Meeting

Buchheit, R.G.; Drewien, C.A.; Martinez, M.A.; Stoner, G.E.

Inorganic polycrystalline hydrotalcite, Li2[Al2(OH)6]2·CO3·3H2O, coatings can be formed on aluminum and aluminum alloys by exposure to alkaline lithium carbonate solutions. This process is conducted using methods similar to traditional chromate conversion coating procedures, but does not use or produce toxic chemicals. The coating provides anodic protection and delays the onset of pitting during anodic polarization. Cathodic reactions are also inhibited which may also contribute to corrosion protection. Recent studies have shown that corrosion resistance can be increased by sealing hydrotalcite coated surfaces to transition metal salt solutions including Ce(NO3)3, KMnO4 and Li2MoO4. Results from these studies are also reported.

More Details

Trace water determination in gases by infrared spectroscopy

Institute of Environmental Sciences - Proceedings, Annual Technical Meeting

Stallard, Brian R.

Water determination in semiconductor process gases is desirable in order to extend the life of gas delivery systems and improve wafer yields. We review our work in applying Fourier transform infrared spectroscopy to this problem, where a 10 ppb detection limit has been demonstrated for water in N2, HCl, and HBr. The potential for optical determination of other contaminants in these gases is discussed. Also, alternative optical spectroscopic approaches are briefly described. Finally, we discuss methods for dealing with interference arising from water in the instrument beam path, yet outside the sample cell.

More Details

Sensing liquid properties with shear-mode resonator sensors

International Conference on Solid-State Sensors and Actuators, and Eurosensors IX, Proceedings

Martin, Steve W.

Liquid properties are measured from the changes they induce in the resonant frequency and damping of thickness-shear mode quartz resonators. A smooth-surfaced resonator viscously entrains the contacting fluid and responds to the density-viscosity product. Separation of density and viscosity is accomplished using two devices: one with a smooth surface and one with a corrugated surface that traps fluid. By observing the difference in stored and dissipated energies in the contacting fluid, its non-Newtonian characteristics can also be determined.

More Details

Polymer electrolytes. Problems, prospects, and promises

International SAMPE Technical Conference

Nagasubramanian, Ganesan

This paper reviews the evolution of polymer electrolytes from the conventional PEO-LiX salt complexes to the more conducting polyphosphazene and copolymers, gelled electrolytes etc. It also reviews the various chemical approaches including modifying PEO to synthesizing complicated polymer architecture. In addition, it discusses the effect of various lithium salts on the conductivity of PEO-based polymers. Charge/discharge and cycle life data of polymer cells containing oxide and chalcogenide cathodes and lithium (Li) anode will be reviewed. Finally, future research directions to improve the electrolyte properties will be presented.

More Details

High efficiency oxide confined vertical cavity surface emitting lasers

Conference Proceedings - Lasers and Electro-Optics Society Annual Meeting-LEOS

Lear, K.L.

Structure based on aluminum-oxide layers have led to dramatic improvements in VCSELs such as power conversion efficiencies in excess of 50% and threshold currents below 10μA. The low index, insulating aluminum-oxide, formed by selective wet thermal oxidation of AlGaAs, serves as an effective index guide as well as a current injection aperture. This paper presents data on devices with either two aligned apertures above and below the active region or with a single effective aperture above the active region leading to slope efficiencies of up to 1W/A.

More Details

Characterization of a surface micromachined pressure sensor array

Proceedings of SPIE - The International Society for Optical Engineering

Eaton, W.P.; Smith, J.H.

A surface micromachined pressure sensor array has been designed and fabricated. The sensors are based upon deformable, silicon nitride diaphragms with polysilicon piezoresistors. Absolute pressure is detected by virtue of reference pressure cavities underneath the diaphragms. For this type of sensor, design tradeoffs must be made among allowable diaphragm deflection, diaphragm size, and desirable pressure ranges. Several fabrication issues were observed and addressed. Offset voltage, sensitivity, and nonlinearity of 100 μm diameter sensors were measured.

More Details

Solvent effects on silica domain growth in silica/siloxane composite materials

International SAMPE Technical Conference

Ulibarri, Tamara A.

The effect of solvent addition on the phase separation, mechanical properties and thermal stability of silica/siloxane composite materials prepared by in situ reinforcement was examined. The addition of a solvent enhances the miscibility of the reinforcement precursor, a partial hydrolyzate of tetraethoxysilane (TEOS-PH), with the polydimethylsiloxane (PDMS) polymer. As a result, the phase separation at the micron level, termed the large-scale structure, diminished in size. This decrease in particle size resulting from the addition of moderate amounts of solvent was accompanied by an improvement in the mechanical properties. However, solvent addition in the excess of 50 weight percent led to a decrease in mechanical properties even though the large-scale structure continued to diminish in size. Small Angle X-Ray Scattering (SAXS) was used to examine the angstrom level or small-scale structure. This small-scale structure was only affected by the presence of solvent, not the amount. The silica/siloxane composite materials showed the same thermal transition temperatures as the original PDMS material.

More Details

Materials issues in lithium ion rechargeable battery technology

International SAMPE Technical Conference

Doughty, Daniel H.

Lithium ion rechargeable batteries are predicted to replace Ni/Cd as the workhorse consumer battery. The pace of development of this battery system is determined in large part by the availability of materials and the understanding of interfacial reactions between materials. Lithium ion technology is based on the use of two lithium intercalating electrodes. Carbon is the most commonly used anode material, while the cathode materials of choice have been layered lithium metal chalcogenides (LiMX2) and lithium spinel-type compounds. Electrolytes may be either organic liquids or polymers. Although the first practical use of graphite intercalation compounds as battery anodes was reported in 1981 for molten salt cells and in 1983 for ambient temperature systems, it was not until Sony Energytech announced a new lithium ion intercalating carbon anode in 1990, that interest peaked. The reason for this heightened interest is that these electrochemical cells have the high energy density, high voltage and light weight of metallic lithium, but without the disadvantages of dendrite formation on charge, improving their safety and cycle life. This publication will review recent developments in the field and materials needs that will enhance future prospects for this important electrochemical system.

More Details

Singlet oxygen and organic light-emitting diodes

International SAMPE Technical Conference

Jacobs, S.J.

The preparation of light emitting diodes employing a new class of materials, 5,10-dihetera-5,10-dihydro-indeno[3,2b]indenes, as hole transport agents is described. These materials have been found to be more resistant to degradation by singlet oxygen than a poly(p-phenylene vinylene) (PPV) derivative.

More Details

Deep x-ray lithography for micromechanics

Proceedings of SPIE - The International Society for Optical Engineering

Christenson, Todd R.

Extensions of the German LIGA process have brought about fabrication capability suitable for cost effective production of precision engineered components. The process attributes allow fabrication of mechanical components which are not capable of being made via conventional subtractive machining methods. Two process improvements have been responsible for this extended capability which involve the areas of thick photoresist application and planarization via precision lapping. Application of low-stress x-ray photoresist has been achieved using room temperature solvent bonding of a preformed photoresist sheet. Precision diamond lapping and polishing has provided a flexible process for the planarization of a wide variety of electroplated metals in the presence of photoresist. Exposure results from the 2.5 GeV National Synchrotron Light Source storage ring at Brookhaven National Laboratory have shown that structural heights of several millimeter and above are possible. The process capabilities are also well suited for microactuator fabrication. Linear and rotational magnetic microactuators have been constructed which use coil winding technology with LIGA fabricated coil forms. Actuator output forces of 1 milliNewton have been obtained with power dissipation on the order of milliWatts. A rotational microdynamometer system which is capable of measuring torque-speed data is also discussed.

More Details

Plasma process control with optical emission spectroscopy

American Society of Mechanical Engineers, Manufacturing Engineering Division, MED

Ward, P.P.

Plasma processes for etching and desmear of electronic components and printed wiring boards (PWB) are difficult to predict and control. Non-uniformity of most plasma processes and sensitivity to environmental changes make it difficult to maintain process stability from day to day. To assure plasma process performance, weight loss coupons or post-plasma destructive testing must be used. The problem with these techniques is that they are not real-time methods and do not allow for immediate diagnosis and process correction. These tests often require scrapping some fraction of a batch to insure the integrity of the rest. Since these tests verify a successful cycle with post-plasma diagnostics, poor test results often determine that a batch is substandard and the resulting parts unusable. These tests are a costly part of the overall fabrication cost. A more efficient method of testing would allow for constant monitoring of plasma conditions and process control. Process anomalies should be detected and corrected before the parts being treated are damaged. Real time monitoring would allow for instantaneous corrections. Multiple site monitoring would allow for process mapping within one system or simultaneous monitoring of multiple systems. Optical emission spectroscopy conducted external to the plasma apparatus would allow for this sort of multifunctional analysis without perturbing the glow discharge. In this paper, optical emission spectroscopy for non-intrusive, in situ process control will be explored along with applications of this technique towards process control, failure analysis and endpoint determination.

More Details

Exciton annihilation studies in poly(p-phenylene vinylene)

International SAMPE Technical Conference

Valencia, V.S.

To verify the excitonic nature of the light-emitting state in PPV, fluorescence intensities and decay lifetimes were investigated as a function of excitation intensity. The results agree with the behavior predicted by the molecular exciton model. In particular, exciton-exciton annihilation causes the fluorescence intensity to saturate and the fluorescence lifetime to shorten at high exciton densities. In addition, the exciton annihilation, and thus diffusion, coefficients are found to be relatively large, even at low temperatures, indicating that exciton migration is important in PPV. These results indicate that the fluorescent (photoluminescent) state in PPV is excitonic in nature. The results argue against the band model where high mobility at reduced temperatures is not expected because the light-emitting species, neutral bipolarons, are associated with large lattice distortions.

More Details

Ceramic granule strength variability and compaction behavior

International SAMPE Technical Conference

Glass, Sarah J.

Diametral compression strength distributions and the compaction behavior and of irregular shape 150-200 μm ceramic granules and uniform-size 210 μm glass spheres were measured to determine how granule strength variability relates to compaction behavior of granular assemblies. High variability in strength, represented by low Weibull modulus values (m<3) was observed for ceramic granules having a distribution of sizes and shapes, and for uniform-size glass spheres. Compaction pressure data were also analyzed using a Weibull distribution function, and the results were very similar to those obtained from the diametral compression strength tests for the same material. This similarity suggests that it may be possible to model granule compaction using a weakest link theory, whereby an assemblage of granules is viewed as the links of a chain, and failure of the weakest granule (i.e., the weakest link) leads to rearrangement and compaction. Additionally, with the use of Weibull statistics, it appears to be possible to infer the variability in strength of individual granules from a simple pressure compaction test, circumventing the tedious task of testing individual granules.

More Details

Applied mechanics modeling of granulated ceramic powder compaction

International SAMPE Technical Conference

Mahoney, F.M.

In ceramic manufacturing processes such as dry-pressing, correlations between applied compacting pressure and resultant powder compact density are essential for defining reliable process conditions for ceramic components. Pressure-density diagrams have been developed as a tool for both process control and for understanding the compaction behavior of different powders. These types of diagrams, however, pertain only to the average properties of a powder compact and do not address a significant issue in powder compaction processes: the formation of density gradients within the compact. Continuum-based mechanics models of varying complexity have addressed the influence of frictional forces acting at the powder-die wall interface which dissipate the applied pressure throughout the compact. Resulting pressure distribution models are then typically coupled with empirical functions relating pressure and density to obtain a green density distribution in the compact. All of these models predict similar trends; however, none predict the distribution with sufficient accuracy to be considered as a design tool for industrial applications.

More Details

Development of an electrical impedance tomography system for an air-water vertical bubble column

American Society of Mechanical Engineers, Heat Transfer Division, (Publication) HTD

O'Hern, Timothy J.

Because the components of a multiphase flow often exhibit different electrical properties, a variety of probes have been developed to study such flows by measuring impedance in the region of interest. Researchers are now using electric fields to reconstruct the impedance distribution within a measurement volume via Electrical Impedance Tomography (EIT). EIT systems employ voltage and current measurements on the boundary of a domain to create a representation of the impedance distribution within the domain. The development of the Sandia EIT system (S-EIT) is reviewed. The construction of the projection acquisition system is discussed and two specific EIT inversion algorithms are detailed. The first reconstruction algorithm employs boundary element methods, and the second utilizes finite elements. The benefits and limitations of EIT systems are also discussed. Preliminary results are provided.

More Details

Embedded micromechanical devices for the monolithic integration of MEMS with CMOS

Technical Digest - International Electron Devices Meeting

Smith, J.H.; Montague, S.; Sniegowski, J.J.; Mcwhorter, P.J.

A flexible, modular manufacturing process for integrating micromechanical and microelectronic devices has been developed. This process embeds the micromechanical devices in an anisotropically etched trench below the surface of the wafer. Prior to microelectronic device fabrication, this trench is refilled with oxide, chemical-mechanically polished, and sealed with a nitride cap in order to embed the micromechanical devices below the surface of the planarized wafer. The feasibility of this technique in a manufacturing environment has been demonstrated by combining a variety of embedded micromechanical structures with a 2 μm CMOS process on 6 inch wafers. A yield of 78% has been achieved on the first devices manufactured using this technique.

More Details
Results 96926–96950 of 100,993
Results 96926–96950 of 100,993
Top