Publications

Results 96376–96400 of 100,993

Search results

Jump to search filters

Results of the first year of operation at Embalse Nuclear Power Station in Argentina

Dupree, S.A.

As a part of the International Remote Monitoring Project, during March 1995, a Remote Monitoring System (RMS) was installed at the Embalse Nuclear Power Station in Embalse, Argentina. This system monitors the status of four typical Candu spent fuel dry storage silos. The monitoring equipment for each silo consists of analog sensors for temperature and gamma radiation measurement; digital sensors for motion detection; and electronic fiber-optic seals. The monitoring system for each silo is connected to a wireless Authenticate Item Monitoring System (AIMS). This paper describes the operation of the RMS during the first year of the trial and presents the results of the signals reported by the system compared with the on site inspections conducted by the regulatory bodies, ABACC, IAEA, ENREN. As an additional security feature, each sensor periodically transmits authenticated State-of-Health (SOH) messages. This feature provides assurance that all sensors are operational and have not been tampered with. The details of the transmitted information and the incidents of loss of SOH, referred to as Missing SOH Event, and the possible causes which produced the MSOHE are described. The RMS at the embalse facility uses gamma radiation detectors in a strong radiation field of spent fuel dry storage silos. The detectors are Geiger Muller tubes and Silicon solid state diodes. The study of the thermal drift of electronics in GM detectors and the possible radiation damage in silicon detectors is shown. Since the initial installation, the system has been successfully interrogated from Buenos Aires and Albuquerque. The experience gained, and the small changes made in the hardware in order to improve the performance of the system is presented.

More Details

Synchronization of multiple magnetically switched modules to power linear induction adder accelerators

Reed, Kim W.

In applications where multiple magnetic modulators are used to drive a single Linear Induction Voltage Adder (LIVA) or Linear Accelerator (LINAC), it is essential that the outputs of the modulators be synchronized. Output rise times are typically in the 10 ns to 20 ns range, often making it necessary to synchronize to within less than 1 ns. Microprocessor and electronic feedback schemes have been developed and demonstrated that achieve the required level of synchronization, however, they are sophisticated and potentially complex. In a quest for simplicity, this work seeks to determine the achievable level of modulator to modulator timing jitter that can be obtained with simple design practices and passive techniques. Sources of output pulse time jitter in magnetic modulators are reviewed and some basic modulator design principles that can be used to minimize the intrinsic time jitter between modulators are discussed. A novel technique for passive synchronization is presented.

More Details

Progress in pulsed power fusion

Quintenz, Jeffrey P.

Pulsed power offers and efficient, high energy, economical source of x-rays for inertial confinement fusion (ICF) research. We are pursuing two main approaches to ICF driven with pulsed power accelerators: intense light ion beams and z-pinches. This paper describes recent progress in each approach and plans for future development.

More Details

Risk management - What about software?

Risks in software systems arise from many directions. There are risks that the software is faulty, that the system may be attacked, that safety hazards exist, that the system may be inoperable or untimely, that an abnormal event may cause unexpected actions, etc. Risk analysis tools should support and document risk-mitigation decisions and facilitate understanding of residual risks. These tools must be based on a sound theory of risk, which does not exist today. Probabilistic risk assessment techniques apply to physically-based systems where failure modes and event dependence are fairly well understood. But they cannot be blindly applied to software systems, which do not share these characteristics. Moreover, we need to meld many diverse aspects of risk for software systems. This presentation will explore some thought-provoking ideas about modeling, problem spaces, solution approaches, math, decision friendly output, and the role of risk analysis in the software lifecycle.

More Details

Programmatic risk management system

Mahn, Jeffrey A.

The purpose of the Programmatic Risk Management System (PRMS) is to evaluate and manage potential risks associated with proposed projects (i.e., new products or processes, or possible research and technological development projects). Although the PRMS considers some technical aspects of risk, the primary focus of the methodology is programmatic risk. That is, the methodology permits an assessment of risks associated with such issues as the ability to successfully produce a product that performs in accordance with all customer requirements, and the availability and allocation of resources (money, equipment, facilities, skilled personnel). The PRMS process consists of five formalized activities that are essential for effective management of risks associated with proposed projects. These activities include risk assessment, development of appropriate risk mitigation strategies, estimating strategy implementation cost, ranking of risk mitigation strategies for resource allocation, and scheduling of strategy implementing. The PRMS utilizes a ranking system that allows the user to identify the most cost-effective investment of resources of minimizing risk.

More Details

Cl{sub 2}+Ar reactive-ion-beam etching of InGaAlAs for smooth, low- damage definition of asymmetric Fabry-Perot optical transmission modulators

Vawter, G.A.; Fritz, I.J.; Drummond, T.J.; Lee, S.R.; Hafich, M.J.; Armendariz, M.G.; Briggs, R.D.; Casalnuovo, S.A.; Griego, L.

Cl{sub 2}+Ar Reactive-Ion-Beam Etching is demonstrated for anisotropic, low-damage etching of InAlGaAs semiconductor alloys for use as optical transmission modulators at 1.32 {mu}m wavelength.

More Details

Quantitative prediction of stresses during thermoset cure

Adolf, Douglas B.

Two thin-walled Al tubes were filled with epoxy which were cured isothermally; one tube was instrumented with strain gauges, and the other with thermocouples. Finite element codes were used. Predicted and measured centerline hoop strains are shown; predictions and measurements agree. This is being applied to encapsulated components.

More Details

Versatile materials for use as chemically sensitive interfaces in SAW-based sensor arrays

Ricco, A.J.

The primary research objective of the work described here is to design, synthesize, and characterize new materials for use as chemical sensor interfaces, integrate these materials, using appropriate transducers, into sensor arrays, and then develop appropriate mathematical algorithms for interpreting the array response. In this paper, we will discuss two new types of materials we have developed that are ideally suited for use as chemically sensitive interfaces for array-based chemical sensing applications, since they: (1) provide general specificity towards classes of functional groups rather than individual compounds; (2) are intermediate in structure between monolayers and polymers; (3) exhibit both endo- and exo-recognition. The first class of materials is surface-confined dendrimers and the second is hyperbranched polymers.

More Details

Shrinkage and microstructural development during drying of organically modified silica xerogels

Brinker, C.J.

We have studied the different driving forces behind syneresis in MTES/TEOS gels by aging them in different H{sub 2}O/EtOH pore fluids. We show using shrinkage, density, contact angle, and N{sub 2} sorption measurements, the influence of gel/solvent interactions on the microstructural evolution during drying. Competing effects of syneresis (that occurs during aging) and drying shrinkage resulted in the overall linear shrinkage of the organically modified gels to be constant at {approximately}50%. Increasing the hydrophobicity of the gels caused the driving force for syneresis to change from primarily condensation reactions to a combination of condensation and solid/liquid interfacial energy. In addition the condensation driven shrinkage was observed to be irreversible, whereas the interfacial free energy driven shrinkage was observed to be partially reversible. Nitrogen sorption experiments show that xerogels with the same overall extent of shrinkage can have vastly different microstructures due to the effects of microphase separation.

More Details

Mass transport, corrosion, plugging, and their reduction in solar dish/Stirling heat pipe receivers

Adkins, Douglas R.

Solar dish/Stirling systems using sodium heat pipe receivers are being developed by industry and government laboratories here and abroad. The unique demands of this application lead to heat pipe wicks with very large surface areas and complex three-dimensional flow patterns. These characteristics can enhance the mass transport and concentration of constituents of the wick material, resulting in wick corrosion and plugging. As the test times for heat pipe receivers lengthen, we are beginning to see these effects both indirectly, as they affect performance, and directly in post-test examinations. We are also beginning to develop corrective measures. In this paper, we report on our test experiences, our post-test examinations, and on our initial effort to ameliorate various problems.

More Details

Using transverse isotropy to model arbitrary deformation-induced anisotropy

Brannon, Rebecca M.

A unifying framework is developed for the analysis of brittle materials. Heretofore diverse classes of models result from different choices for unspecified coefficient and distribution functions in the unified theory. Material response is described in terms of expectation integrals of transverse symmetry tensors. First, a canonical body containing cracks of all the same orientation is argued to possess macroscopic transverse isotropy. An orthogonal basis for the linear subspace consisting of all double-symmetric transversely-isotropic fourth-order tensors associated with a given material vector is introduced and applied to deduce the explicit functional dependence of the compliance of such contrived materials on the shared crack orientation. A principle of superposition of strain rates is used to write the compliance for a more realistic material consisting of cracks of random size and orientation as an expectation integral of the transverse compliance for each orientation times the joint distribution function for the size and orientation. Utilizing an evolving (initially exponential) size- dependence in the joint distribution, the general theory gives unprecedented agreement with measurements of the dynamic response of alumina to impact loading, especially upon release where the calculations predict the development of considerable deformation- induced anisotropy, challenging the conventional notion of shocks as isotropic phenomena.

More Details

MPICH on the T3D: A case study of high performance message passing

Brightwell, Ronald B.

This paper describes the design, implementation and performance of a port of the Argonne National Laboratory/Mississippi State University MPICH implementation of the Message Passing Interface standard to the Cray T3D massively parallel processing system. A description of the factors influencing the design and the various stages of implementation are presented. Performance results revealing superior bandwidth and comparable latency as compared to other full message passing systems on the T3D are shown. Further planned improvements and optimizations, including an analysis of a port to the T3E, are mentioned.

More Details

The processing, properties and use of the pyrotechnic mixture titanium subhydride/potassium perchlorate

Massis, Thomas M.

Development of this pyrotechnic occurred because of the need for a static insensitive material to meet personnel safety requirements and related system safety issues in nuclear weapon energetic material component designs. Ti subhydride materials are made by the thermal dehydrding of commercial Ti hydride powder to the desired equivalent hydrogen composition in the Ti lattice. These Ti subhydrides, when blended with K perchlorate, meet the static insensitivity requirement of not being initiated from an equivalent human body electrostatic discharge. Individual material and blend qualification requirements provide a reproducible material from lot to lot. These pyrotechnic formulations meet the high reliability requirements (0.9995) for initiation and performance parameters and have the necessary stability and compatibility to meet long lived requirements of more than 25 years. Various experiences and problems are also discussed that have led to a mature technology for Ti subhydride/K perchlorate during its use in energetic material component designs.

More Details

SmartWeld: A knowledge-based approach to welding

Mitchiner, John L.

SmartWeld is a concurrent engineering system that integrates product design and processing decisions within an electronic desktop engineering environment. It is being developed to provide designers, process engineers, researchers and manufacturing technologists with transparent access to the right process information, process models, process experience and process experts, to realize``right the first time`` manufacturing. Empirical understanding along with process models are synthesized within a knowledge-based system to identify robust fabrication procedures based on cost, schedule, and performance. Integration of process simulation tools with design tools enables the designer to assess a number of design and process options on the computer rather than on the manufacturing floor. Task models and generic process models are being embedded within user friendly GUI`s to more readily enable the customer to use the SmartWeld system and its software tool set without extensive training. The integrated system architecture under development provides interactive communications and shared application capabilities across a variety of workstation and PC-type platforms either locally or at remote sites.

More Details

New developments in electrical linewidth and overlay metrology for ULSI fabrication processes

Sniegowski, Jeffry J.

Compared to other metrology approaches, electrical test structures for the measurement of dimensional characteristics such as linewidth and overlay directly relate to the electrical performance of the circuits being fabricated. The inherent disadvantage of electrical techniques is that they can be applied only to the extraction of the dimensions of features patterned in electrically-conducting materials. They can not be directly applied to patterned resist films or dielectric material layers. In the case of narrow on-wafer features patterned in resist, for example, linewidths are preferably extracted by electron-beam methods. These methods are sufficiently repeatable for monitoring fabrication-process variations. However, the traceability of the units in which linewidth is expressed is thwarted by the unavailability of suitable calibration artifacts. In the case of overlay metrology, the same limitations as regards electrical conduction apply. However, similar advantages accrue in principle to electrical overlay methods when they can be utilized. It is the electrical quality of the overlay of a conducting via relative to underlying or overlying conducting material which is of driving importance for circuit functionality. This may differ from the overlay values extracted from the same patterns by commonly-used optical overlay tools. Further refinements in the state of the art in both electrical linewidth and electrical overlay metrologies are desirable as feature sizes and spacings continue to shrink in emerging generations of devices. This paper discusses some recent innovations which have been recently introduced and indicates new roles for electrical metrology in low-cost certification of reference materials for both linewidth and overlay applications.

More Details

Properties of dynamically compacted WIPP salt

Brodsky, Nancy S.

Dynamic compaction of mine-run salt is being investigated for the Waste Isolation Pilot Plant (WIPP), where compacted salt is being considered for repository sealing applications. One large-scale and two intermediate-scale dynamic compaction demonstrations were conducted. Initial fractional densities of the compacted salt range form 0.85 to 0.90, and permeabilities vary. Dynamically-compacted specimens were further consolidated in the laboratory by application of hydrostatic pressure. Permeability as a function of density was determined, and consolidation microprocesses were studied. Experimental results, in conjunction with modeling results, indicate that the compacted salt will function as a viable seal material.

More Details

A shaft seal system for the Waste Isolation Pilot Plant

Hansen, Francis D.

As part of the demonstration of compliance with federal regulations, a shaft seal system has been designed for the Waste Isolation Pilot Plant. The system completely fills the 650 m shafts with components consisting of the common engineering materials, each of which possesses low permeability, longevity, and can be constructed using available technology. Design investigations couple rock mechanics and fluid flow analysis and tests of these materials within the natural geological setting, and demonstrate the effectiveness of the design.

More Details

An examination of Sandia`s phenomenological computer codes and the use of intelligent searching in risk assessments

Benjamin, A.S.

Because many of the phenomenologically based codes used to support risk assessments require lone execution times, it is important to have a rationally based means for optimizing the choice of parameter values that are input to the code calculations. For this reason, we have developed a method for intelligently searching the space of parameter values to deduce, with as few computations as possible, the values that are most likely to lead to high risk. We have applied the method to a problem involving electrical initiation of an explosive due to the response of the system to fires. We have shown that our method can locate potential risk vulnerabilities with far fewer time-consuming physical response computations than would be necessary using standard sampling approaches.

More Details

National and international nuclear material monitoring

Waddoups, I.G.

The status of nuclear materials in both the U.S. and Former Soviet Union is changing based upon the execution of agreements relative to weapons materials production and weapon dismantlement. The result of these activities is that a considerably different emphasis is being placed on how nuclear materials are viewed and utilized. Even though much effort is being expended on the final disposition of these materials, the interim need for storage and security of the material is increasing. Both safety and security requirements exist to govern activities when these materials are placed in storage. These requirements are intended to provide confidence that the material is not being misused and that the storage operations are conducted safely. Both of these goals can be significantly enhanced if technological monitoring of the material is performed. This paper will briefly discuss the traditional manual methods of U.S. and international material monitoring and then present approaches and technology that are available to achieve the same goals under the evolving environment.

More Details

A computer based system for prioritizing pollution prevention opportunity assessments at SNL/NM

Walsh, M.L.

Prioritizing waste generators is necessary to determine which are the best candidates for Pollution Prevention Opportunity Assessments (PPOAs). This paper describes the Sandia National Laboratories/New Mexico (SNL/NM) PPOA Ranking System. The system uses a multimedia approach that considers hazardous and radioactive waste disposal data, and hazardous chemical usage data (from which air emissions are extrapolated). Pollution prevention information is included, from the SNL Pollution Prevention Opportunities database that identifies waste streams that have readily apparent pollution prevention opportunities. The system also considers the relative costs of waste management and the chargeback fees paid for waste generation. From these data, organizations are ranked with an algorithm developed in Microsoft Access{trademark} on a personal computer. The concept could readily be transferred to other facilities needing to decide where to perform PPOAs.

More Details

Discovering system requirements

Bahill, A.T.

Cost and schedule overruns are often caused by poor requirements that are produced by people who do not understand the requirements process. This report provides a high-level overview of the system requirements process, explaining types, sources, and characteristics of good requirements. System requirements, however, are seldom stated by the customer. Therefore, this report shows ways to help you work with your customer to discover the system requirements. It also explains terminology commonly used in the requirements development field, such as verification, validation, technical performance measures, and the various design reviews.

More Details

Testing to estimate the Munson-Dawson parameters

Fossum, Arlo F.

Parameter estimation for modern viscoplastic constitutive models often requires data from many tests. Sensitivity coefficients can be used to design an efficient test matrix and reduce testing requirements. The present study derives sensitivity coefficients for each model parameter in the Munson-Dawson constitutive model and evaluates them for several load histories.

More Details

A study of lead-acid battery efficiency near top-of-charge and the impact on PV system design

Stevens, J.W.; Corey, G.P.

Knowledge of the charge efficiency of lead-acid batteries near top-of-charge is important to the design of small photovoltaic systems. In order to know how much energy is required from the photovoltaic array in order to accomplish the task of meeting load, including periodic full battery charge, a detailed knowledge of the battery charging efficiency as a function of state of charge is required, particularly in the high state-of-charge regime, as photovoltaic systems are typically designed to operate in the upper 20 to 30% of battery state-of-charge. This paper presents the results of a process for determining battery charging efficiency near top-of-charge and discusses the impact of these findings on the design of small PV systems.

More Details

Design and implementation of MPI on Puma portals

Brightwell, Ronald B.

As the successor to SUNMOS [8], the Puma operating system provides a flexible, lightweight, high performance message passing environment for massively parallel computers. Message passing in Puma is accomplished through the use of a new mechanism known as a portal. Puma is currently running on the Intel Paragon and is being developed for the Intel TeraFLOPS machine. In this paper we discuss issues regarding the development of the Argonne National Laboratory/Mississippi State University implementation of the Message Passing Interface standard on top of portals. Included is a description of the design and implementation for both MPI point-to- point and collective communications, and MPI-2 one-sided communications.

More Details

Development of the nuclear weapons complex EP architecture

Halbleib, Laura L.

The Nuclear Weapons Guidance Team is an interagency committee led by Earl Whiteman, DOE that chartered the generation of EP40100, Concurrent Qualification and its successor EP401099, Concurrent Engineering and Qualification. As this new philosophy of concurrent operations has evolved and as implementation has been initiated, conflicts and insufficiencies in the remaining Engineering Procedures (EPs) have become more apparent. At the Guidance Team meeting in November 1995, this issue was explored and several approaches were considered. It was concluded at this meeting, that a smaller set of interagency EPs described in a hierarchical system could provide the necessary interagency direction to support complex-wide implementation. This set consolidates many existing EP processes where consistency and commonality are critical to success of the extended enterprise. The Guidance Team subsequently chartered an interagency team to initiate development activity associated with the envisioned new EP set. This team had participation from seven Nuclear Weapons Complex (NWC) sites as well as DOE/AL and DP-14 (team members are acknowledged later in this report). Per the Guidance Team, this team, referred to as the Architecture Subcommittee, was to map out and define an EP Architecture for the interagency EPs, make recommendations regarding a more agile process for EP approval and suggest an aggressive timeline to develop the combined EPs. The Architecture Subcommittee was asked to brief their output at the February Guidance Team meeting. This SAND report documents the results of the Architecture Subcommittee`s recommendations.

More Details
Results 96376–96400 of 100,993
Results 96376–96400 of 100,993
Top