The material point method (MPM) is an evolution of the particle in cell method where Lagrangian particles or material points are used to discretize the volume of a material. The particles carry properties such as mass, velocity, stress, and strain and move through a Eulerian or spatial mesh. The momentum equation is solved on the Eulerian mesh. Modifications to the material point method are developed that allow the simulation of thin membranes, compressible fluids, and their dynamic interactions. A single layer of material points through the thickness is used to represent a membrane. The constitutive equation for the membrane is applied in the local coordinate system of each material point. Validation problems are presented and numerical convergence is demonstrated. Fluid simulation is achieved by implementing a constitutive equation for a compressible, viscous, Newtonian fluid and by solution of the energy equation. The fluid formulation is validated by simulating a traveling shock wave in a compressible fluid. Interactions of the fluid and membrane are handled naturally with the method. The fluid and membrane communicate through the Eulerian grid on which forces are calculated due to the fluid and membrane stress states. Validation problems include simulating a projectile impacting an inflated airbag. In some impact simulations with the MPM, bodies may tend to stick together when separating. Several algorithms are proposed and tested that allow bodies to separate from each other after impact. In addition, several methods are investigated to determine the local coordinate system of a membrane material point without relying upon connectivity data.
This work was performed to characterize the time dependent deformation behavior of two solder alloys typically used in radar applications, 40Sn-40In-20Pb and 50In-50Pb by weight percent. The near-eutectic 60Sn-40Pb alloy was sued as a baseline comparison. The time-dependent deformation was measured using isothermal uniaxial compression creep tests. The data was reduced and, using a least squares fit algorithm, formatted into the Sherby-Dorn power law creep equation. The derived constitutive relationships were then used as a primary input to a solid mechanics, finite element model to predict solder joint lifetime and reliability. For a fixed applied stress, 40Sn-40In-20Pb had slower creep rates, at all temperatures, compared to 50In-50Pb and the baseline near eutectic 60Sn-40Pb solder. At temperatures above 70 C, the 50In-50Pb had faster creep rates than 60 Sn-40Pb. At lower temperatures, the 60Sn-40Pb solder had a higher creep rate due, in part, to its heterogeneous structure and large number of grain boundaries available for grain boundary sliding and rotation compared to 50In-50Pb.
Many deep-space satellites contain a plutonium heat source. An explosion, during launch, of a rocket carrying such a satellite offers the potential for the release of some of the plutonium. The fireball following such an explosion exposes any released plutonium to a high-temperature chemically-reactive environment. Vaporization, condensation, and agglomeration processes can alter the distribution of plutonium-bearing particles. The Fireball code package simulates the integrated response of the physical and chemical processes occurring in a fireball and the effect these processes have on the plutonium-bearing particle distribution. This integrated treatment of multiple phenomena represents a significant improvement in the state of the art for fireball simulations. Preliminary simulations of launch-second scenarios indicate: (1) most plutonium vaporization occurs within the first second of the fireball; (2) large non-aerosol-sized particles contribute very little to plutonium vapor production; (3) vaporization and both homogeneous and heterogeneous condensation occur simultaneously; (4) homogeneous condensation transports plutonium down to the smallest-particle sizes; (5) heterogeneous condensation precludes homogeneous condensation if sufficient condensation sites are available; and (6) agglomeration produces larger-sized particles but slows rapidly as the fireball grows.
This document reports on the accomplishments of a laboratory-directed research and development (LDRD) project whose objective was to initiate a research program for developing a fundamental understanding of multiphase multicomponent subsurface transport in heterogeneous porous media and to develop parallel processing computational tools for numerical simulation of such problems. The main achievement of this project was the successful development of a general-purpose, unstructured grid, multiphase thermal simulator for subsurface transport in heterogeneous porous media implemented for use on massively parallel (MP) computers via message-passing and domain decomposition techniques. The numerical platform provides an excellent base for new and continuing project development in areas of current interest to SNL and the DOE complex including, subsurface nuclear waste disposal and cleanup, groundwater availability and contamination studies, fuel-spill transport for accident analysis, and DNAPL transport and remediation.
Self-assembled monolayers (SAMs) having surfaces terminated in the following functional groups: -CH{sub 3}, -OH, -COOH, and (COO{sup -}){sub 2}Cu{sup 2+} (MUA-Cu{sup 2+}) have been prepared and examined as potential chemically sensitive interfaces. Mass measurements made using surface acoustic wave (SAW) devices indicate that these surfaces display different degrees of selectivity and sensitivity to a range of analytes. The response of the MUA-Cu{sup 2+} SAM to the nerve-agent simulant diisopropyl methylphosphonate (DIMP) is particularly intriguing. Exposure of this surface to 50%-of-saturation DIMP yields a surface concentration equivalent to about 20 DIMP monolayers. Such a high surface concentration in equilibrium with a much lower-than-saturation vapor pressure has not previously been observed. Newly developed analytical tools have made it possible to measure the infrared spectrum of the chemically receptive surface during analyte dosing. Coupled with in-situ SAW/ellipsometry measurements, which permit simultaneous measurement of mass and thickness with nanogram and Angstrom resolution, respectively, it has been possibly to develop a model for the surface chemistry leading to the unusual behavior of this system. The results indicate that DIMP interacts strongly with surface-confined Cu{sup 2+} adduct that nucleates growth of semi-ordered crystallites having substantially lower vapor pressure than the liquid.
A new gravitational head formulation for the treatment of stratified flows has been developed for CONTAIN, a lumped-parameter code used primarily for the analysis of postulated accidents in nuclear power plants. This new hybrid formulation is discussed and compared in this paper with the old, average-density CONTAIN formulation. In addition, these formulations are assessed against experimental data from three large-scale experiments in which stratified conditions were observed. These are the NUPEC M-8-1, Surtsey ST-3, and the HDR E11.2 experiments.
The Dicer algorithm generates a fine mesh by refining each element in a coarse all-hexahedral mesh generated by any existing all-hexahedral mesh generation algorithm. The fine mesh is geometry-conforming. Using existing all-hexahedral meshing algorithms to define the initial coarse mesh simplifies the overall meshing process and allows dicing to take advantage of improvements in other meshing algorithms immediately. The Dicer algorithm will be used to generate large meshes in support of the ASCI program. The authors also plan to use dicing as the basis for parallel mesh generation. Dicing strikes a careful balance between the interactive mesh generation and multi-million element mesh generation processes for complex 3D geometries, providing an efficient means for producing meshes of varying refinement once the coarse mesh is obtained.
The use of feature recognition as part of an overall decomposition-based hexahedral meshing approach is described in this paper. The meshing approach consists of feature recognition, using a c-loop or hybrid c-loop method, and the use of cutting surfaces to decompose the solid model. These steps are part of an iterative process, which proceeds either until no more features can be recognized or until the model has been completely decomposed into meshable sub-volumes. This method can greatly reduce the time required to generate an all-hexahedral mesh, either through the use of more efficient meshing algorithms on more of the geometry or by reducing the amount of manual decomposition required to mesh a volume.
Packages for the transportation of radioactive material must meet performance criteria to assure safety and environmental protection. The stringency of the performance criteria is based on the degree of hazard of the material being transported. Type B packages are used for transporting large quantities of radioisotopes (in terms of A{sub 2} quantities). These packages have the most stringent performance criteria. Material with less than an A{sub 2} quantity are transported in Type A packages. These packages have less stringent performance criteria. Transportation of LSA and SCO materials must be in {open_quotes}strong-tight{close_quotes} packages. The performance requirements for the latter packages are even less stringent. All of these package types provide a high level of safety for the material being transported. In this paper, regulatory tests that are used to demonstrate this safety will be described. The responses of various packages to these tests will be shown. In addition, the response of packages to extra-regulatory tests will be discussed. The results of these tests will be used to demonstrate the high level of safety provided to workers, the public, and the environment by packages used for the transportation of radioactive material.
In the author`s current position at Sandia National Laboratories within the Pulsed Power Sciences Center, much of the author`s time is spent in composing short (one page) technical reports and long (> 20 page) technical contracts and program plans for transmission to the Department of Energy and to upper management and also in reviewing long technical documents for accuracy. A major requirement of these efforts is to complete them on a timely basis, often within a few hours or a few days. In this talk, the author reveals some communication {open_quotes}secrets{close_quotes} that have been learned. The idea behind these twelve {open_quotes}secrets{close_quotes} is to get the answers you, as a nonmanager, need quickly from a manager without creating stress either on your part or the manager`s part.
The Waste Isolation Pilot Plant (WIPP) is the U.S. Department of Energy`s (DOE) planned repository for transuranic waste generated by defense programs. The WIPP repository 660 meters underground in bedded salt. Bedded salt was chosen for the repository because of salt`s small moisture content, extremely low permeability, and its natural ability to flow or creep, effectively encapsulating the waste in the long-term. However, because of these unique characteristics, the ability to measure properties at in situ conditions are beyond the realm of most standard experimental equipment. Thus a suite of new experimental systems and techniques has been developed to measure properties in extremely {open_quotes}tight{close_quotes} (low permeability) rocks. Also, innovations in rock property measurements have been made for standard porous media through the research conducted to characterize the rocks above the repository. A number of the new systems and techniques developed through the WIPP are presented in this paper. Examples include permeameters, two-phase flow characterization equipment, techniques for evaluation of salt healing, and characterization of diffusive processes.
The Joint ESARDA/INMM Workshop on Science and Modem Technology for Safeguards was held in Arona, Italy, October 28-31, 1996. It was attended by some 120 participants, consisting principally of scientists from various disciplines and safeguards experts from the inspectorates. The Workshop provided a full discussion on the near and far term scientific technologies that may be applied to safeguards. In addition, there were extended discussions on the social and political aspects surrounding the areas of Nonproliferation, International Safeguards, and Regional Safeguards. The general opinion was that the Workshop met and exceeded its goals, setting the stage for future workshops of this type. One of the outstanding characteristics of this Workshop was the ample amount of time allowed for full discussion of each presentation, both for technical issues and social/political issues. This procedure was substantially different from the usual ESARDA and INMM meetings. This paper will discuss the organization and conduct of the Workshop, as well as the results as reported by the four Working Group Chairs and the Workshop Co-chairs.
This paper presents the results of switching voltages of 500 V and currents of 10 A using chemical vapor deposited (CVD) diamond as a switching material. The switching is performed by using an electron beam that penetrates the diamond, creates electron hole pairs, and lowers its resistivity to about 20 {Omega}-cm and its resistance to about 4 {Omega}. Tests were performed at room temperature but in a configuration that allows for 250 C.
This paper describes several recent advances for fabricating coated surface acoustic wave (SAW) sensors for applications requiring trace chemical detection. Specifically, we have demonstrated that high surface area microporous oxides can provide 100-fold improvements in SAW sensor responses compared with more typical polymeric coatings. In addition, we fabricated GaAs SAW devices with frequencies up to 500 MHz to provide greater sensitivity and an ideal substrate for integration with high-frequency electronics.
There are several process variables which are crucial to the control of vacuum arc remelting of segregation sensitive alloys. These are: electrode gap, melt rate, cooling rate, furnace annulus, furnace atmosphere and electrode quality (i.e. cleanliness and integrity). Of these variables, active, closed loop control is usually applied only to electrode gap. Other variables are controlled by controlling furnace operational parameters to preset schedules (e.g. melting current is ramped or held constant to control melt rate in an open loop fashion), through proper maintenance and calibration of equipment (e.g. to ensure proper cooling water and gas flow rates, or to accomplish an acceptable vacuum leak rate), through proper practice of procedures, and by maintaining electrode quality control. Electrode gap control is accomplished by controlling an electrode gap indicator such as drip-short frequency (or period) to a specified set-point. This type of control, though often adequate, ignores information available from other electrode gap indicators and is susceptible to upsets. A multiple input electrode gap controller is described which uses optimal estimation techniques to address this problem.
This paper presents the results of tests performed on a variety of electrothermal microactuators and arrays of these actuators recently fabricated in the four-level planarized polycrystalline silicon (polysilicon) SUMMiT process at the U.S. Department of Energy`s Sandia National Laboratories. These results are intended to aid designers of thermally actuated mechanisms, and will apply to similar actuators made in other polysilicon MEMS processes. The measurements include force and deflection versus input power, maximum operating frequency, effects of long term operation, and ideal actuator and array geometries for different design criteria. A typical application in a stepper motor is shown to illustrate the utility of these actuators and arrays.
Continuum mixture theory and mesoscale modeling are applied to describe the behavior of shock-loaded heterogeneous media. One-dimensional simulations of gas-gun experiments demonstrate that the wave features are well described by mixture theory, including reflected wave behavior and conditions where significant reaction is initiated. Detailed wave fields are resolved in numerical simulations of impact on a lattice of discrete explosive {open_quotes}crystals{close_quotes}. It is shown that rapid distortion first occurs at material contact points; the nature of the dispersive fields includes large amplitude fluctuations of stress over several particle pathlengths. Localization of energy causes {open_quotes}hot-spots{close_quotes} due to shock focusing and plastic work as material flows into interstitial regions.
CPA - Cost and Performance Analysis - is a prototype integration of existing PC-based cost and performance analysis tools: ACEIT (Automated Cost Estimating Integrated Tools) and ASSESS (Analytic System and Software for Evaluating Safeguards and Security). ACE is an existing DOD PC-based tool that supports cost analysis over the full life cycle of a system; that is, the cost to procure, operate, maintain and retire the system and all of its components. ASSESS is an existing DOE PC-based tool for analysis of performance of physical protection systems. Through CPA, the cost and performance data are collected into Excel workbooks, making the data readily available to analysts and decision makers in both tabular and graphical formats and at both the system and subsystem levels. The structure of the cost spreadsheets incorporates an activity-based approach to cost estimation. Activity-based costing (ABC) is an accounting philosophy used by industry to trace direct and indirect costs to the products or services of a business unit. By tracing costs through security sensors and procedures and then mapping the contributions of the various sensors and procedures to system effectiveness, the CPA architecture can provide security managers with information critical for both operational and strategic decisions. The architecture, features and applications of the CPA prototype are presented. 5 refs., 3 figs.
This paper describes the work at Sandia National Laboratories to develop sensors that remotely detect unique life-form characteristics, such as breathing patterns or heartbeat patterns. This paper will address the Technical Support Working Group`s (TSWG) objective: to develop a remote vital signs detector which can be used to assess someone`s malevolent intent. The basic concept of operations for the projects, system development issues, and the preliminary results for a radar device currently in-house and the implications for implementation are described. A survey that identified the in-house technology currently being evaluated is reviewed, as well as ideas for other potential technologies to explore. A radar unit for breathing and heartbeat detection is being tested, and the applicability of infrared technology is being explored. The desire for rapid prototyping is driving the need for off-the-shelf technology. As a conclusion, current status and future directions of the effort are reviewed.
The need to understand how particle radiation (high-energy photons and electrons) from a variety of sources affects materials and electronics has motivated the development of sophisticated computer codes that describe how radiation with energies from 1.0 keV to 100.0 GeV propagates through matter. Predicting radiation transport is the necessary first step in predicting radiation effects. The radiation transport codes that are described here are general-purpose codes capable of analyzing a variety of radiation environments including those produced by nuclear weapons (x-rays, gamma rays, and neutrons), by sources in space (electrons and ions) and by accelerators (x-rays, gamma rays, and electrons). Applications of these codes include the study of radiation effects on electronics, nuclear medicine (imaging and cancer treatment), and industrial processes (food disinfestation, waste sterilization, manufacturing.) The primary focus will be on coupled electron-photon transport codes, with some brief discussion of proton transport. These codes model a radiation cascade in which electrons produce photons and vice versa. This coupling between particles of different types is important for radiation effects. For instance, in an x-ray environment, electrons are produced that drive the response in electronics. In an electron environment, dose due to bremsstrahlung photons can be significant once the source electrons have been stopped.
Simulation of the effects of explosives on structures is a challenge because the explosive response can best be simulated using Eulerian computational techniques and structural behavior is best modeled using Lagrangian methods. Due to the different methodology of the two computational techniques and code architecture requirements, they are usually implemented in different computer programs. Explosive and structure modeling in two different codes make it difficult or next to impossible to do coupled explosive/structure interaction simulations. Sandia National Laboratories has developed two techniques for solving this problem. The first is called Smoothed Particle Hydrodynamics (SPH), a relatively new gridless method comparable to Eulerian, that is especially suited for treating liquids and gases such as those produced by an explosive. The SPH capability has been fully implemented into the transient dynamics finite element (Lagrangian) codes PRONTO-2D and -3D. A PRONTO-3D/SPH simulation of the effect of a blast on a protective-wall barrier is presented in this paper. The second technique employed at Sandia uses a new code called Zapotec that combines the 3-D Eulerian code CTH and the Lagrangian code PRONTO-3D with minimal changes to either code. CTH and PRONTO-3D are currently executing on the Sandia Terraflops machine (9000 Pentium Pro processors). Eulerian simulations with 100 million cells have been completed on the current configuration of the machine (4500 Pentium Pro processors). The CTH and PRONTO-3D combination will soon be executing in a coupled fashion on this machine.
The financial system in the United States is slowly migrating from the bricks and mortar of banks on the city square to branch banks, ATM`s, and now direct linkage through computers to the home. Much work has been devoted to the security problems inherent in protecting property and people. The impact of attacks on the information aspects of the financial system has, however, received less attention. Awareness is raised through publicized events such as the junk bond fraud perpetrated by Milken or gross mismanagement in the failure of the Barings Bank through unsupervised trading activities by Leeson in Singapore. These events, although seemingly large (financial losses may be on the order of several billion dollars), are but small contributors to the estimated $114 billion loss to all types of financial fraud in 1993. Most of the losses can be traced to the contribution of many small attacks perpetrated against a variety of vulnerable components and systems. This paper explores the magnitude of these financial system losses and identifies new areas for security to be applied to high consequence events.
This paper discusses recent applications by Sandia National Laboratories of cooled and uncooled thermal infrared imagers to wide-area security assessment systems. Thermal imagers can solve many security assessment problems associated with the protection of high-value assets at military bases, secure installations, and commercial facilities. Thermal imagers can provide surveillance video from security areas or perimeters both day and night without expensive security lighting. Until fairly recently, thermal imagers required open-loop cryogenic cooling to operate. The high cost of these systems and associated maintenance requirements restricted their widespread use. However, recent developments in reliable, closed-loop, linear drive cryogenic coolers and uncooled infrared imagers have dramatically reduced maintenance requirements, extended MTBF, and are leading to reduced system cost. These technology developments are resulting in greater availability and practicality for military as well as civilian security applications.
Solar thermal electric (STE) technologies--parabolic troughs, power towers, and dish/engine systems--can convert sunlight into electricity efficiently and with minimum effect on the environment. These technologies currently range from developmental to early commercial stages of maturity. This paper summarizes the results of a recent strategic planning effort conducted by the US department of Energy (DOE) to develop a long-term strategy for the development of STE technologies. The planning team led by DOE included representatives from the solar thermal industry, domestic utilities, state energy offices, and Sun{center_dot}Lab (the cooperative Sandia National laboratories/National Renewable Energy Laboratory partnership that supports the STE Program) as well as project developers. The plan was aimed at identifying specific activities necessary to achieve the DOE vision of 20 gigawatts of installed STE capability by the year 2020. The planning team developed five strategies that both build on the strengths of, and opportunities for, STE technology and address weaknesses and threats. These strategies are to: support future commercial opportunities for STE technologies; demonstrate improved performance and reliability of STE components and systems; reduce STE energy costs; develop advanced STE systems and applications; and address nontechnical barriers and champion STE power. The details of each of these strategies are discussed.
Intrusion detection systems sometimes use radio signals to convey sensor status in areas that wire conduits do not service or as a redundant path to wired systems. Some applications benefit from radio technology by minimizing setup time and reducing installation and operation costs. In recent years with the explosion in wireless communications, these radio-based security systems have become more capable while lowering costs, size, and power consumption. However, the very nature of radio communication raises issues regarding setup, operation, and security of these systems. Sandia National Laboratories, in cooperation with government and industry, has addressed many of these issues through the analysis and development of security systems, communications protocols, and operational procedures. Message encryption and frequent channel supervision are used to enhance security. Installation and maintenance of these systems are simplified by incorporating built-in radio link analysis, menu-driven configuration equipment, and other techniques. Commercial communications satellites and spread-spectrum radios are also being integrated to provide unique capabilities to the security community. The status of this work is presented here along with details of its development.
