Wave energy converters (WECs) are designed to produce useful work from ocean waves. This useful work can take the form of electrical power or even pressurized water for, e.g., desalination. This report details the findings from a wave tank test focused on that production of useful work. To that end, the experimental system and test were specifically designed to validate models for power transmission throughout the WEC system. Additionally, the validity of co-design informed changes to the power take-off (PTO) were assessed and shown to provide the expected improvements in system performance.
Coe, Ryan G.; Lee, Jantzen; Bacelli, Giorgio B.; Spencer, Steven; Dullea, Kevin; Plueddemann, Albert J.; Buffitt, Derek; Reine, John; Peters, Donald; Spinneken, Johannes; Hamilton, Andrew; Sabet, Sahand; Husain, Salman; Jenne, Dale (Scott); Korde, Umesh; Muglia, Mike; Taylor, Trip; Wade, Eric
The “Pioneer WEC” project is targeted at developing a wave energy generator for the Coastal Surface Mooring (CSM) system within the Ocean Observatories Initiative (OOI) Pioneer Array. The CSM utilizes solar photovoltaic and wind generation systems, along with rechargeable batteries, to power multiple sensors on the buoy and along the mooring line. This approach provides continuous power for essential controller functions and a subset of instruments, and meets the full power demand roughly 70% of the time. Sandia has been tasked with designing a wave energy system to provide additional electrical power and bring the CSM up-time for satisfying the full-power demand to 100%. This project is a collaboration between Sandia and Woods Hole Oceanographic Institution (WHOI), along with Evergreen Innovations, Monterey Bay Aquarium Research Institute (MBARI), Eastern Carolina University (ECU), Johns Hopkins University (JHU), and the National Renewable Energy Laboratory (NREL). This report captures Phase I of an expected two phase project and presents project scoping and concept design results. phase project and presents project scoping and concept design results.
This report describes the testing of a model scale wave energy converter. This device, which uses two aps that pivot about a central platform when excited by waves, has a natural frequency within the range of the waves by which it is excited. The primary goal of this test was to assess the degree to which previously developed modeling, experimentation, and control design methods could be applied to a broad range of wave energy converter designs. Testing was conducted to identify a dynamic model for the impedance and excitation behavior of the device. Using these models, a series of closed loop tests were conducted using a causal impedance matching controller. This report provides a brief description of the results, as well as a summary of the device and ex- perimental design. The results show that the methods applied to this experimental device perform well and should be broadly applicable.
This paper describes the design and performance of a synthetic rope on sheave drive system. This system uses synthetic ropes instead of steel cables to achieve low weight and a compact form factor. We demonstrate how this system is capable of 28-Hz torque control bandwidth, 95% efficiency, and quiet operation, making it ideal for use on legged robots and other dynamic physically interactive systems. Component geometry and tailored maintenance procedures are used to achieve high endurance. Endurance tests based on walking data predict that the ropes will survive roughly 247,000 cycles when used on large (90 kg), fully actuated bipedal robot systems. The drive systems have been incorporated into two novel bipedal robots capable of three-dimensional unsupported walking. Robot data illustrate effective torque tracking and nearly silent operation. Finally, comparisons with alternative transmission designs illustrate the size, weight, and endurance advantages of using this type of synthetic rope drive system.
A new multi-year effort has been launched by the Department of Energy to validate the extent to which control strategies can increase the power produced by resonant wave energy conversion (WEC) devices. This paper describes the design of a WEC device to be employed by this program in the development and assessment of WEC control strategies. The operational principle of the device was selected to provide a test-bed for control strategies, in which a specific control strategies effectiveness and the parameters on which its effectiveness depends can be empirically determined. Numerical design studies were employed to determine the device geometry, so as to maximize testing opportunities in the Maneuvering and Seakeeping (MASK) Basin at the Naval Surface Warfare Centers David Taylor Model Basin. Details on the physical model including specific components and model fabrication methodologies are presented. Finally the quantities to be measured and the mechanisms of measurement are listed.