Transit time, the time from bridgewire burst until breakout of detonation from the output pellet of an exploding bridgewire detonator, was measured as a function of burst current. From this data, in conjunction with known equations for run distance versus pressure, unreacted explosive Hugoniots, and detonation properties of the initial pressing pellet, the run distance in the initial pressing explosive pellet and shock pressure from the exploding bridgewire were determined, both as a function of burst current.
Fifteen years of solar thermal technology development have produced a considerable amount of knowledge relating to the production of electricity from central receiver power plants. This body of knowledge is under examination by researchers from the United States and the Federal Republic of Germany for the purpose of defining the next generation central receiver electricity producers. This second generation power plant is expected to represent a significant step towards commercialization of these systems. During the course of the study, specific activities needed to realize this next-step technology are being defined. The study is an international team effort. Under the International Energy Agency Small Solar Power Systems project, researchers from DLR, Interatom, Sandia National Laboratories, and Bechtel have designed a study in which technologies relating to existing systems are quantified, logical next-step systems are characterized, and future potential advances are identified. The receiver concepts under investigation are: salt-in- tube, volumetric, and direct absorption. Two plant performance levels are examined, 30 and 100 MW{sub e}. Each concept is applied with common capacity factors, solar multiples, and types and sizes of heliostats at each performance level. Availability and uncertainty analyses are also performed. Annual energy production figures are calculated using the SOLERGY computer code. Capital and Operation and Maintenance cost methodologies are mutually agreed upon in order that levelized energy cost calculations will be consistent for each power plant. During the course of this effort, further potential advances in central receiver technology have continued to become apparent. These possible areas for improvement will be described. An additional comparison is being made between central receivers and trough-based systems. 8 refs., 2 figs.
A hierarchical control architecture for telerobotic vehicles intended to yield a modular, flexible, and easily expanded control system is presented. This architecture is proposed for applications where simple teleoperation is required but where additional capabilities might be quickly added without major changes to the control system. Similarities to the NASREM architecture are noted. Results are given from hardware implementation of the control system on a telerobotic vehicle, Raybot, at Sandia National Laboratories.
A systematic study is described which addresses the technical issues associated with launching flier-plates intact to hypervelocitites. First, very high pressures are needed to launch the flier plates to hypervelocitites, and second this high pressure loading must be uniform and nearly shockless. To achieve both these criteria, a graded-density material referred to as a pillow'' is used to impact a flier plate. When this graded-density material is used to impact a flier plate at high velocities on a two-stage light-gas gun, nearly shockless megabar pressure pulses are introduced into the flier plate. Since the loading on the flier plate is shockless, melting of the flier plate is prevented. This technique has been used to launch a 2-mm thick titanium alloy (Ti-6Al-4V) plate to a velocity of 8.1 km/s, and a 1-mm thick aluminum alloy (6061-T6) plate to a velocity of 10.4 km/s. A method is described by which the flier plate velocities could be further augmented to velocities approaching 14 km/s. 18 refs., 16 figs.
A new technique is reported for the rapid determination of interstitial oxygen (O{sub i}) in heavily doped n{sup +} and p{sup +} silicon. This technique includes application of a selective electrochemical thinning (SET) process and FTIR transmittance measurement on a limited area of a silicon wafer. The O{sub i} is calculated using ASTM F1188--88 with the IOC 88 calibration factor. An advantage of SET over mechanical thinning is that the original wafer thickness and diameter are maintained for additional processing. 1 tab.
The Shippable Storage Cask Demonstration Project is intended to demonstrate casks which can be used for both shipping and storing spent nuclear fuel assemblies. The demonstration included the requirement that the casks be certified for shipping by the US Nuclear Regulatory Commission (NRC). After a lengthy review process which resulted in the resolution of several important technical issues, designs for two similar casks have been certified. This paper describes the certification phase of the demonstration. Based on experience gained during certification phase of the demonstration. Based on experience gained during certification, observations and recommendations have been developed which can benefit others seeking NRC approval of transportation cask designs.
Reviews of normal breakdown and current induced avalanche breakdown mechanisms in silicon power transistors are presented. We show the applicability of the current induced avalanche model to heavy ion induced burnouts. Finally, we present solutions to current induced avalanche in silicon power semiconductors. 7 refs., 5 figs.
The electronic properties of heavily and orderly Si-doped nipi structures in GaAs are studied theoretically using the ab-initio self-consistent pseudopotential method within the local density approximation. Two nipi configurations are considered. Besides investigating the nature of the impurity-related band edge states, the xy-planar-averaged local ionic and self-consistent potentials are also analyzed. The screening effect of the host crystal on the doping induced potential is found to be small. The effects of the doping induced electric field and the strain due to dopings are also examined. 13 refs., 9 figs., 2 tabs.
The near field surrounding buried waste in the proposed high level nuclear waste repository in Yucca Mountain, Nye County, Nevada, is a region where strongly heat driven processes can exist. These strongly heat driven processes further complicate an already very difficult problem, i.e,. predicting groundwater flow and chemical transport through unsaturated fractured, heterogeneous porous media. The coupling between fluid flow and heat emanation is central to understanding these strongly heat driven processes. Although it is important that all of couplings be investigated, the intent of this paper is to discuss the mathematical models and associated computer codes that can be used in investigating the coupled heat emanation and fluid flow in unsaturated porous media. The information in this paper should be useful to those studying these phenomena, validating these models, or investigating the coupling of fluid flow and heat emanation with the other phenomena. The codes implementing these models are commonly referred to as nonisothermal two-phase flow codes. 5 refs., 4 tabs.
The United States Department of Energy (DOE) is developing the Waste Isolation Pilot Plant (WIPP), located in southeastern New Mexico, for disposal of transuranic wastes generated by defense programs. The DOE must first demonstrate compliance with the Environmental Protection Agency's (EPA) Environmental Standards for the Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes hereafter called the Standard. The Containment Requirements in Subpart B of the Standard set limits on the probability that cumulative radionuclide releases to the accessible environment during the 10,000 years following decommissioning of the repository will exceed certain limits. To comply with these requirements, performance assessments must construct a modeling system that can adequately simulate all realistic future states of the repository that might result in radionuclide releases. Because the regulatory limits are probabilistic, performance assessments must accurately reflect variability and uncertainty within all factors that contribute to the simulation, including variability and uncertainty within all factors that contribute to the simulation, including variability in material properties, probabilities of future human actions, and uncertainties inherent in the conceptual and numerical models that simulate reality. This paper describes conceptual and numerical improvements in the performance assessment methodology made during 1990, and summarizes the present status of WIPP performance assessment. All results to date are preliminary, and cannot be used to determine compliance or non-compliance. The DOE anticipates determining compliance after evaluating a final performance assessment in 1994. 11 refs., 3 figs.
Low pressure (200 Torr) metalorganic chemical vapor deposition (MOCVD) of InSb has been examined through variation of the Column III (TMIn) and Column V (TMSb or TESb) precursor partial pressures. The use of lower growth pressure significantly enhanced the range of allowable Column III Column V partial pressures in which specular morphology InSb could be obtained without the formation of In droplets or Sb crystals. In addition, a 70% improvement in the average hole mobility was obtained, compared to InSb grown in the same reactor at atmospheric pressure. SIMS analysis revealed that Si at the substrate/epitaxial layer interface is an important impurity that may contribute to degradation of the mobility. Substitution of TESb for TMSb did not result in any improvement in the purity of the InSb. 6 refs.
The long length and relatively small cross sectional area of the robotic arms envisioned for use inside of the underground nuclear waste storage tanks will require the control of flexible structures. This will become an important problem in the characterization and remediation of these tanks. We are developing control strategies to actively damp residual vibrations in flexible robotic arms caused by high speed motion and abrupt external forces. A planar, two-link flexible arm is currently being used to test these control strategies. In this paper, two methods of control are discussed. The first is a minimum-time control approach which utilizes a finite element model and and optimization program. These tools plan the motor torque profiles necessary for the tip of the arm to move along a straight line, in minimum time, within the motors' torque constraints, and end in a quiescent state. To account for modeling errors in the finite element model, errors in joint angles, velocities, and link curvatures are added to the optimal torque trajectory. Linear quadratic Gaussian (LQG) regulatory design theory is used to determine the feedback gains. The second method of control is a teleoperated joystick controller which uses an input shaping technique to alter the commands of the joystick so as to reduce the residual vibration of the fundamental modes. Approximating the system as linear, the natural frequency and damping ratio are estimated on-line for the complete system, which includes the structure plus a lower level proportional derivative controller. An input shaping filter is determined from the estimated natural frequency, estimated damping ratio, and the desired transfer function of the system. 11 reps., 9 figs.
Muir, J.F.; Hogan Jr., R.E.; Skocypec, R.D.; Buck, R.
The concept of solar driven chemical reactions in a commercial-scale volumetric receiver/reactor on a parabolic concentrator was successfully demonstrated in the CAtalytically Enhanced Solar Absorption Receiver (CAESAR) test. Solar reforming of methane (CH{sub 4}) with carbon dioxide (CO{sub 2}) was achieved in a 64-cm diameter direct absorption reactor on a parabolic dish capable of 150 kW solar power. The reactor was a catalytic volumetric absorber consisting of a multi-layered, porous alumina foam disk coated with rhodium (Rh) catalyst. The system was operated during both steady-state and solar transient (cloud passage) conditions. The total solar power absorbed reached values up to 97 kW and the maximum methane conversion was 70%. Receiver thermal efficiencies ranged up to 85% and chemical efficiencies peaked at 54%. The absorber performed satisfactorily in promoting the reforming reaction during the tests without carbon formation. However, problems of cracking and degradation of the porous matrix, nonuniform dispersion of the Rh through the absorber, and catalyst deactivation due to sintering and possible encapsulation, must be resolved to achieve long-term operation and eventual commercialization. 17 refs., 11 figs., 1 tab.
We have performed MD simulations of adhesive phenomena, on an atomic scale, between metals possessing both smooth and stepped-surfaces. Studies of adhesion between identical metals, consisting of either Au, Cu, or Ni, with (001) or (111) orientations, reveal the existence of adhesive avalanches as the bodies are brought to within a critical separation ({approximately}2 {angstrom}). That is, as the surfaces approach one another, one or both surface layers becomes unstable, and abruptly moves toward the other. This signals a transition from an initial system with two distinct surfaces to one possessing no identifiable surfaces. The presence of adhesive avalanches will pose difficulties in determining adhesive forces and energies by means of atomic force microscopy at sub-nanometer separations of probe tip and sample surface. 7 refs., 3 figs.
An improved standard total-dose test method is described to qualify electronics for a low-dose radiation environment typical of space systems. The method consists of {sup 60}Co irradiation at a dose rate of 1--3 Gy(Si)/s (100--300 rad(Si)/s) and a subsequent 373 K (100{degree}C) bake. New initiatives in radiation hardness assurance are also briefly discussed, including the Qualified Manufacturers List (QML) test methodology and the possible use of 1/f noise measurements as a nondestructive screen for oxide-trap charge related failure. 8 refs.
A two-stage data compression technique that provides for exact, bit-for-bit recovery is described. The first stage is a modified form of conventional linear prediction which generates an error or residue sequence in such a way that exact reconstruction of the original data sequence can be accomplished with a simple recovery algorithm. The second stage is bi-level sequence coding. Even though the residue sequence from the first stage is essential white and Gaussian with seismic or other similar waveform data, bi-level sequence coding will generally provide further compression. The complete technique is described briefly in this summary, and examples of its performance are presented. A full paper on the algorithm is available from the author. 12 refs., 2 figs., 2 tabs.
We have synthesized a new tool, a lasing phase diagram, for designing high efficiency surface-emitting laser resonators and have demonstrated its usefulness by fabricating and operating many different laser resonators. 4 refs., 4 figs.
This paper is concerned with controlling the morphology of microporous polymers prepared via thermal demixing of solutions. 2 wt % solutions of poly(acrylonitrile) in maleic anhydride, a poor solvent, are first cooled to produce separated polymer-rich and solvent-rich phases. Removing the solvent by freeze drying then produces a microporous material having a density of 33 mg/cm{sup 3}, a void fraction of 97%, and a pore size of about 10 {mu}m. We find that the morphology cannot be explained by existing models, which focus on phase diagrams and kinetics of phase transformations during cooling of the solution. In conflict with those models, we find that two radically different morphologies can be produced even when the polymer concentration and cooling path are held strictly constant. A hypothesis that polymer degradation causes the different morphologies is not supported by GPC, {sup 13}C NMR, and FTIR experiments. Instead, we offer evidence that the different microporous morphologies are caused by different polymer conformations in solutions having the same concentration and temperature. 11 refs., 3 figs.
The nuclear industry uses sensitive or classified parts and material that must be protected and accounted for. We believe there is a need for an automated system that can help protect and inventory these parts and material. In response to this need Sandia National Laboratories Division 5245 is developing a personnel and material tracking system named PAMTRAK to safeguard sensitive parts and material at selected Department of Energy facilities. This paper describes the project's background, design goals and features.
Sandia National Laboratories has developed a variety of alarm communication and display systems for a broad spectrum of users. This paper will briefly describe the latest systems developed for the Department of Energy (DOE), the Department of Defense (DoD), and the Department of State (DOS) applications. Applications covered will vary from relatively small facilities to large complex sites. Ongoing system developments will also be discussed. The concluding section will summarize the practical, implementable state-of-the-art features available in new systems. 6 figs.
The mechanical behavior of microcellular open-cell foams prepared by a thermally induced phase separation process are investigated. The foams studied were prepared from isotactic polystyrene, polyacrylonitrile, and poly(4-methyl-1-pentene) (rigid foams), and polyurethane and Lycra (elastomeric foams). Their densities were in the range 0.04--0.27 g/cm3. Conventional polystyrene foams were used for comparison. The moduli and collapse stresses of these foams were measured in compression and compared with the current constitutive laws which relate mechanical properties to densities. A reinforcement technique based on the in-situ precipitation of silica was used to improve the mechanical properties. 13 refs., 4 figs., 3 tabs.
Ion implantation has been shown to produce unique improvements in the properties of a wide range of materials. This technology has been extensively used for doping of semiconductors, where the required doses and implantation depths are relatively modest and readily achieved with commercial implanters. Other applications of ion implantation currently being pursued at a commercial level include the synthesis of buried second-phase layers in Si and the improvement of metal surface properties such as hardness, friction, wear rate, and corrosion. However, these applications have been severely constrained by the costs of treating large surface areas with the high ion doses required, and by the need to produce modified layers thicker than the range of the sub-MeV ions available from presently available commercial high-flux ion implanters. It therefore seems worthwhile to consider whether pulsed ion accelerators may offer advantages for such applications by providing high ion fluxes at MeV energies. The previously reported applications of pulsed accelerators to materials modification have used sub-MeV ion energies. The purpose of this article is to being these considerations the perspective of materials scientists who use ion implantation. We comment on needed extensions in implantation capabilities while leaving to others the question of whether these needs can be met with pulsed-beam technology. Further, in order to illustrate the kinds of beneficial materials modifications that can be achieved with implantation, we provide examples from recent work at Sandia National Laboratories, where large improvements have been realized in the tribological properties and strengths of Fe and A{ell} alloys. 10 refs., 6 figs.
The natural language technique was just one of many approaches to information system design in 1987. The success of this approach convinced management of the viability of this new'' approach. A group was created to use natural language in information system specifications and designs. Two of the projects undertaken by this group will be reviewed. The first is a quality database that allows for the management of the process that certifies production capabilities for major weapon components and the second tracks command and control status of weapons. A third external project involving nuclear disarmament will also be discussed.
The United States Department of Energy (DOE) plans to use the Waste Isolation Pilot plant (WIPP) in southeastern New Mexico for disposal of transuranic wastes generated by defense programs. The DOE must first demonstrate compliance with the Environmental Protection Agency's (EPA) Environmental Standards for the Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes (40 CFR Part 191) hereafter called the Standard. The Standard was vacated by a Federal Court of Appeals in 1987 and is undergoing revision; by agreement with the State of New Mexico the DOE will continue to evaluate repository performance with respect to the Standard as first promulgated until a new version is available. This paper reviews the results of a 1989 preliminary demonstration of the performance-assessment methodology that will be used by the WIPP project ultimately to assess compliance with the Standard. The report also describes conceptual and numerical improvements in the performance-assessment methodology made during 1990, and summarizes the progress made toward achieving the probabilistic assessment of repository performance required for regulatory compliance. 13 refs., 4 figs.
Low-density, microcellular polymer foams have numerous applications as structural supports in high-energy physics experiments, in catalysis, ion exchange, and filtration, and for a variety of biomedical uses. A versatile method to prepare such foams is by thermally-induced phase separation (TIPS) of polymer solutions. Demixed solutions can be transformed into a foam by freezing the demixed solution and removing the solvent by freeze-drying. The morphology of these foams is determined by the the thermodynamics and kinetics of phase separation. A model of both the early and late stage structure development for demixed polymer solutions will be presented. For semi-crystalline polymers, gels can be prepared by crystallizing the polymer from solution, either a homogeneous solution or a demixed solution. Foams can be prepared from these gels by the supercritical extraction of the solvent. By understanding and utilizing the phase separation behavior of polymer solutions, engineered microcellular foams can be prepared. To design the foams for any application one must be able to characterize their morphology. Results will be presented on the morphological characterization of these foams and the relationship of the morphology to their processing history. 14 refs., 12 figs.