Publications

Results 100126–100150 of 100,993

Search results

Jump to search filters

Vindicator ETW-250 test report

Greer, G.S.

The Vindicator ETW-250 taut wire system combines a physical taut wire barrier with an intrusion detection sensor network. The sensor wires deter and/or slow physical entry into protected areas. The sensors themselves generate an alarm if the sensor wires are pulled, spread, cut, or climbed on. This physical motion is converted into an electrical waveform that is analyzed by the processor. The processor then determines if this motion is within the pre-programmed parameters. If it is not, an alarm is generated through a relay back to the monitoring station. Small changes, such as those caused by temperature, are rejected. Installation and testing are described.

More Details

Equipment for potential unattended use in treaty verification applications

Drayer, D.D.

Containment and Surveillance (C/S) equipment, which is used in international safeguards applications, is normally expected to operate unattended within a facility in a host country for extended periods of time. To ensure that this equipment consistently provides high-quality data, the equipment used to ensure the data's integrity must be highly reliable and tamper-resistant. Although designed specifically for use by the International Atomic Energy Agency to comply with the Non-Proliferation Treaty, the equipment has potential applications for both bilateral and multilateral verification schemes for other treaties. This report describes C/S equipment that has been developed by Sandia National Laboratories, and discusses its potential applications. This equipment includes surveillance equipment, seals, monitoring equipment, and authentication equipment. 16 refs., 20 figs.

More Details

Initial reference seal system design: Waste Isolation Pilot Plant

Nowak, E.J.

Waste Isolation Pilot Plant (WIPP) sealing program results are embodied in the initial seal system strategy and reference design. The design provides a common basis for calculations and analyses so that results can be compared directly. The sealing strategy combines both long- and short-term seal components. Crushed salt is the principal long-term barrier to fluid flow. Short-term seal components are used until creep consolidation is sufficient. Concretes developed specifically for WIPP seals and a swelling clay material that exhibits low permeability to WIPP groundwater and brine have been chosen for the short-term components. A body of evidence exists showing the stability of these materials for the length of time they are required to function. Reference designs are described and drawings are shown for each of the principal multi-component seals. Confidence in the sealing strategy and the reference designs resulted from a combination of laboratory tests, numerical modeling, and in situ demonstrations. The sealing strategy, materials, and designs for the WIPP repository are consistent with the concepts and designs proposed previously for other national and international waste management programs. Past accomplishments and planned activities in the sealing program will produce a detailed conceptual design for the seal system and a seal system performance model. 48 refs., 11 figs., 6 tabs.

More Details

Standardized communication symbols to facilitate circuit design

George, M.; Pierson, L.G.

In the course of communication circuit design at Sandia National Laboratories, a set of communication symbols was created to aid, and hopefully standardize, the design process. These symbols, which allow the designer to build a circuit using black boxes, simplify circuit design and documentation. They also provide a standard set to help minimize interpretation problems among circuit designers. The symbols can be used to represent various devices in a circuit, such as modems, computers, terminals, encryption devices, converters, etc. When using these symbols to design communication circuits, the contours of each symbol show which devices interface together. Mismatch device contours indicate the need for another element (such as a null modem) between the two devices. In addition, the propagation of clock, data, and control signals through the circuit can be represented. Clocking modes on synchronous components (modems, multiplexers, etc.) and signal line crossovers can also be determined from the drawings during the design process. 30 figs.

More Details

High-voltage pulse testing of DSSL (detonator strong safety link) actuator drive cables

Neau, E.L.

More Details

Solderability testing of Kovar with 60Sn40Pb solder and organic fluxes

Vianco, Paul T.

The solderability of 60Sn40Pb solder on Kovar was examined as a function of surface-cleaning procedure, flux, and solder-bath temperature. Organic-acid fluxes were more effective at lowering the contact angle than was a mildly activated, rosin-based (RMA) flux on chemically etched Kovar. The contact angles were as low as 29{degree} {plus minus} 5{degree} as compared to 61{degree} {plus minus} 11{degree}, respectively. Varying the solder temperature through the range of 215{degree}C to 288{degree}C caused an insignificant change in the contact angle for the RMA flux and a decrease of the contact angle for a candidate water-based, organic-acid flux. The dilution strength of the flux and the elapsed cleaning time significantly influenced the solder-flux interfacial tension, {sub {gamma}LF}. T-peel strengths of Kovar-60Sn40Pb-OFHC copper joints had a low correlation with the contact angle derived from the solderability experiments. The results of the solderability tests and the T-peel mechanical tests, and subsequence microanalysis of the as-soldered and T-peel samples revealed that the best results for the RMA flux were achieved by using an electropolishing procedure and a solder temperature of 240{degree}C to 260{degree}C. A relatively low contact angle of 31{degree} {plus minus} 2{degree} was observed, with no evidence of cracking or thick-film intermetallic formation at the Kovar-solder interface. T-peel strengths were nominally 9.4{degree} {plus minus} 0.5 {times} 10{sup 6} dyn/cm. 21 refs., 36 figs., 11 tabs.

More Details

Wind tunnel study of wake downwash behind A 6% scale model B1-B aircraft

Strickland, James H.

Parachute system performance issues such a turnover and wake recontact may be strongly influenced by velocities induced by the wake of the delivering aircraft, especially if the aircraft is maneuvering at the time of parachute deployment. The effect of the aircraft on the parachute system is a function of the aircraft size, weight, and flight path. In order to provide experimental data for validation of a computer code to predict aircraft wake velocities, a test was conducted in the NASA 14 {times} 22 ft wind tunnel using a 5.78% model of the B-1B strategic bomber. The model was strut mounted through the top of its fuselage by a mechanism which was capable of pitching the model at moderate rates. In this series of tests, the aircraft was pitched at 10{degree}/sec from a cruise angle of attack of 5.3{degree} to an angle of attack of 11{degree} in order to simulate a 2.2g pullup. Data were also taken for the subsequent pitch down sequence back to the cruise angle of attack. Instantaneous streamwise and vertical velocities were measured in the wake at a number of points using a hot wire anemometer. These data have been reduced to the form of downwash coefficients which are a function of the aircraft angle of attack time-history. Unsteady effects are accounted for by use of a wake convection lag-time correlation. 12 refs., 59 figs., 4 tabs.

More Details

Elicitation and use of expert judgment in performance assessment for high-level radioactive waste repositories

Bonano, Evaristo J.

This report presents the concept of formalizing the elicitation and use of expert judgment in the performance assessment of high-level radioactive waste (HLW) repositories in deep geologic formations. The report begins with a discussion of characteristics (advantages and disadvantages) of formalizing expert judgment examples of previous uses of expert judgment in radioactive waste programs, criteria that can assist in deciding when to formalize expert judgment, and the relationship of formal use of expert judgment to data collection and modeling. The current state of the art with respect to the elicitation, use, and communication of formal expert judgment is presented. The report concludes with a discussion on potential applications of formal expert judgment in performance assessment of HLW repositories. 93 refs.

More Details

Operations manual for reading VAK-3 ultrasonic seals using a data acquisition box

Walker, J.E.

As part of a Department of Energy/Commission of European Communities (DOE/CEC) cooperative program, Sandia National Laboratories was asked to develop a portable ultrasonic seal pattern reading system. The system consists of a data acquisition box (DAB), a mechanical reading head, and a portable IBM-compatible PC linked to the DAB by a serial RS-232C communication link. This manual focuses on the DAB subsystem. 8 refs., 13 figs., 8 tabs.

More Details

A users' manual for MCPRAM (Monte Carlo PReprocessor for AMEER) and for the fuze options in AMEER (Aero Mechanical Equation Evaluation Routines)

Lafarge, Robert A.

MCPRAM (Monte Carlo PReprocessor for AMEER), a computer program that uses Monte Carlo techniques to create an input file for the AMEER trajectory code, has been developed for the Sandia National Laboratories VAX and Cray computers. Users can select the number of trajectories to compute, which AMEER variables to investigate, and the type of probability distribution for each variable. Any legal AMEER input variable can be investigated anywhere in the input run stream with either a normal, uniform, or Rayleigh distribution. Users also have the option to use covariance matrices for the investigation of certain correlated variables such as booster pre-reentry errors and wind, axial force, and atmospheric models. In conjunction with MCPRAM, AMEER was modified to include the variables introduced by the covariance matrices and to include provisions for six types of fuze models. The new fuze models and the new AMEER variables are described in this report.

More Details

Implementation of initial tests in the Brine Inflow Room (Room Q) of the Waste Isolation Pilot Plant

Nowak, E.J.

The purpose of this report is to summarize for the record the objectives, planning, progress, and documentation of excavating Brine Inflow Room Q and implementing an initial set of Room Q tests. The Room Q tests were designed primarily to test the scale-up accuracy of the current brine inflow model by providing data on brine flow from the host rock salt to a large-scale excavation in the Waste Isolation Pilot Plant (WIPP). Data from these tests will also be used to reduce uncertainties in flow parameters and evaluate proposed mechanistic models. Room Q was excavated with a tunnel boring machine. The initial tests were implemented to measure brine flow parameters and room closure. Pore pressure, permeability, and brine inflow were measured with 15 tools emplaced in boreholes above, below, and on the north side of the room at a station 75 feet into the host rock from the entrance to the room. These measurements were made before, during, and after Room Q was bored to obtain data on the responses in the host rock to the boring process. Closure measurements were started almost immediately after excavation progressed past each measurement station. The designs, timing, sequence, procedures, and as-built records for these tests were documented in Sandia National Laboratories WIPP Quality Assurance files and Westinghouse WIPP Engineering records. 21 refs., 5 figs., 5 tabs.

More Details

A comparison of CTH predictions with experimental armor/anti-armor data for long rod penetrators in two and three dimensions

Hertel, Eugene S.

CTH is a software system under development at Sandia National Laboratories (SNL) to model multidimensional, multi-material, large deformation, strong shock wave physics. One-dimensional rectilinear, cylindrical, and spherical meshes; two-dimensional rectangular, and cylindrical meshes; and three-dimensional rectangular meshes are currently available. A two-step Eulerian solution scheme is used with these meshes. The first step is a Lagrangian step in which the cells distort to follow the material motion. The second step is a remesh step where the distorted cells are mapped back to the original Eulerian mesh. CTH has several thermodynamic models that are used for simulating strong shock, large deformation events. Both tabular and analytic equations of state are available. CTH can model material strength, high explosive detonation, fracture, and motion of fragments smaller than a computational cell. The material strength model is elastic perfectly plastic with thermal softening. A programmed burn model is available for computing the thermodynamic properties of explosive detonation. The Jones-Wilkins-Lee equation of state is available for modelling high explosive reaction products. Fracture can be initiated based on pressure or principle stress. A special model is available for moving fragments smaller than a computational cell with the correct statistical velocity. 7 refs.

More Details

Sandia's CONCEPT-90 photovoltaic concentrator module

Conference Record of the IEEE Photovoltaic Specialists Conference

Chiang, C.J.

A description is given of Sandia's CONCEPT-90 module, which represents a novel type of point-focus photovoltaic concentrator module designed for improved safety, reliability, and performance, and for ease of component fabrication and module assembly. These improvements will combine to decrease the cost of electricity produced by this type of concentrator module. Unique features of the CONCEPT-90 module include encapsulated cell assemblies, simple flat components, and integral use of plastics. The first prototype of this module has been made using back-contact silicon concentrator cells and refractive secondary optical elements. The first prototype module is described, and results from outdoor tests are presented.

More Details

SUPES Version 2. 1: A Software Utilities Package for the Engineering Sciences

Red-Horse, John R.

The Software Utilities Package for the Engineering Sciences (SUPES) is a collection of subprograms which perform frequently used non- numerical services for the engineering applications programmer. The three functional categories of SUPES are: (1) input command parsing, (2) dynamic memory management, and (3) system dependent utilities. The subprograms in categories one and two are written in standard FORTRAN-77, while the subprograms in category three are written to provide a standardized FORTRAN interface to several system dependent features. 2 refs.

More Details

Magnetic-field shielding of satellites from high-energy-electron environments

Vittitoe, C.N.

Magnet configurations are found that limit the 6-MeV electrons threatening satellite electronics to <1% of the incident flux. Successful configurations of permanent magnets and electromagnets require magnetic energies of {approximately}8 to 12 kJ to protect each liter of electronics volume. The fundamental strength of materials leads to a required minimum mass of {approximately}48 to 64 kg/liter to support the magnetic pressure. With the electronics requiring {approximately}5 liters, several hundred kilograms are needed for this support. Except for protecting small apertures, magnetic shielding provides little, if any, advantage over that obtained by coating with an equivalent mass using traditional methods. 7 refs., 9 figs., 1 tab.

More Details

Borehole closure and test zone volume determination program for brine-permeability test results within the Waste Isolation Pilot Plant underground facility

Jensen, A.L.

Until recently, hydrologic characterization in closed sections of boreholes at the Waste Isolation Pilot Plant (WIPP) has relied on measurements of pressure and temperature to establish the permeability of the host geological formations. There were no provisions for monitoring tool compliance and salt creep resulting from borehole closure. The new permeability test tool used to characterize the WIPP underground facility has been equipped with a series of sensors to measure the movement of the tool with respect to the borehole and borehole wall movement. A FORTRAN program can interpret the output data from each test and calculate the change in borehole radius, test zone length, and test zone volume. These values provide a correlation of fluid compressibility and tool compliance with the permeability results derived from the test data. 4 figs., 3 tabs.

More Details

Development of a multi-purpose, pulsed-laser system for solar cell processing applications

Conference Record of the IEEE Photovoltaic Specialists Conference

King, David L.

The capabilities of a versatile Nd:YAG pulsed-laser system developed at Sandia National Laboratories for solar cell processing applications is described. The results of statistically based, multifactor experiments used to characterize the influence of laser-system process variables on patterns produced in silicon wafers and silicon-oxide layers are presented, and an initial assessment of laser-grooved solar cell processing conditions is given.

More Details

Application of InAlAs/GaAs superlattice alloys to GaAs solar cells

Conference Record of the IEEE Photovoltaic Specialists Conference

Drummond, Timothy J.

AlGaAs/GaAs solar cells are typically characterized as having relatively high interface recombination velocities at the heteroface. Some of the factors influencing the design of solar cell window layers are examined, and the effect of substituting InAlAs/GaAs superlattice alloys and InAlAs bulk alloys in place of AlGaAs is considered. Potential advantages are reduced surface recombination at the heterojunction, reduced thermionic emission into the window layer, thinner window layers, and reduced absorption in the window layer. Theoretical models predict a lower effective surface recombination velocity and a smaller acceptor activation energy for superlattice alloys. Experimental absorption data show that superlattice alloys have a lower absorption coefficient at short wavelengths near the UV roll off.

More Details

Test Component Attachment Effects on Resonant Plate Pyrotechnic Shock Simulation

Bell, R.G.; Zimmerman, Roger M.

An accepted technique for simulating pyrotechnic shock inputs has been the resonant plate test. The plate is designed so that its predominant modes generate the desired frequency content of a given shock test specification. The success of the test is dependent on the engineer's ability to effectively design and control the response of the resonant plate. In designing a test to simulated a pyrotechnic environment, the location and mass of the test item become very important considerations since they have a profound impact on the dynamic response of the resonant plate. A relatively massive test item can change the plates's resonant frequency. Differences in the relative frequencies of the test item's fixture and the resonant plate may also effect the input to the test items. In this study, a simple mock test assembly is used to study test item and resonant plate interactions during a test. The implications of this interaction regarding the deviations of the shock test specification are also discussed. Data from shock tests performed with the test assembly mounted to a rigid mounting surface and a flexible resonant plate are compared. Frequency response functions and shock response spectra are generated from the test data and compared to show the significance of: (1) the relative stiffness of the mounting surface; and (2) the location of the input control point during a resonant plate test. These factors are shown to be particularly important in using resonant plate testing to simulate pyrotechnic shock environments.

More Details

Development of a "CRUD'' Particle Size Distribution and its Effect on Cask Source Term and Containment Analyses

Sanders, Thomas L.

Spent pressurized-water reactor (PWR) and boiling-water reactor (BWR) fuel rods from three reactors were examined by hot cell periscope, energy dispersive x-ray analysis, and scanning electron micrography. In the case of fuel from the Quad Cities reactor, it was possible to develop a complete particle size distribution. It was found to be log-normal, with a median geometric diameter of 3 μm and a standard deviation of 1.87 μm.

More Details

Pressure studies of deep levels in semiconductors

High Pressure Research

Samara, George A.

The effects of pressure on the energetics and kinetics of electron emission and capture processes by several important deep levels in Si are discussed. The results yield the first quantitative measures of the breathing mode lattice relaxations accompanying these processes. © 1990, Taylor & Francis Group, LLC. All rights reserved.

More Details

Redundant and independent containment and surveillance systems

Drayer, D.D.; Sonnier, C.S.; Mangan, D.L.; Walford, F.

Facilities are now coming under Agency safeguards which have large amounts of nuclear material and/or nuclear material which is very difficult to access for reverification. Containment and Surveillance (C/S) technologies may be used to assist in resolution of this problem. This study examines the concept of redundant and independent C/S Systems, and discusses how these systems could be used to lower the need for remeasurement of materials which are difficult to access, or materials included in very large inventories. This paper dose not address increasing levels of C/S measures to protect different types of materials. However, the paper does discuss how redundant and independent C/S Systems will improve the reliability of safeguards information. Equipment which may be used in such systems, and examples of potential systems, are presented. Decisions on how much C/S equipment is enough for a given facility, or type of material, must be made by the inspectorate. 6 refs., 4 figs.

More Details

Level III probabilistic risk assessment for N Reactor

Kunsman, David M.

A Level III probabilistic risk assessment (PRA) has been performed for N Reactor, a Department of Energy (DOE) production reactor located on the Hanford reservation in Washington. The objectives of the PRA are to assess the risks to the public and the Hanford site workers posed by the operation of N Reactor, to compare those risks to proposed DOE safety goals, and to identify changes to the plant that could reduce the risk. The scope of the PRA is comprehensive, excluding only sabotage and operation errors of commission. State-of-the-art methodology is employed based largely on the methods developed by Sandia for the US Nuclear Regulatory Commission in support of the NUREG-1150 study of five commercial nuclear power plants. The structure of the probabilistic models allowed complex interactions and dependencies between systems to be explicitly considered. Latin Hypercube sampling techniques were used to develop uncertainty distributions for the risks associated with postulated core damage events initiated by fire, seismic, and internal events as well as the overall combined risk. The combined risk results show that N Reactor meets the primary DOE safety goals and compared favorably to the plants considered in the NUREG-1150 analysis. 36 figs., 81 tabs.

More Details

Some implications of the application or removal of agency seals by facility operators

Walford, F.; Drayer, D.D.; Sonnier, C.S.

This report is the outcome of a study of the technical and procedural requirements which would need to be met if the Agency and facility operators were to agree that under certain circumstances the operator could remove or apply on Agency seal in the absence of an inspector. In the FRG and USA Support Programmes respectively an electronic seal (VACOSS) and a CCTV system (MIVS) have been developed. Through a joint project, an interface has been demonstrated which enables the seal data to be superimposed upon the surveillance data. This interface is briefly described in the appendix. A proposed application for this integrated system is to allow facility operators to carry-out some of the seal procedures normally performed by an inspector, thereby reducing the need for inspector presence at certain crucial times.

More Details
Results 100126–100150 of 100,993
Results 100126–100150 of 100,993
Top