Uncertainty and sensitivity analysis techniques based on Latin hypercube sampling, partial correlation analysis and stepwise regression analysis are used in an investigation with the MACCS model of the early health effects associated with a severe accident at a nuclear power station. The primary purpose of this study is to provide guidance on the variables to be considered in future review work to reduce the uncertainty in the important variables used in the calculation of reactor accident consequences. The effects of 34 imprecisely known input variables on the following reactor accident consequences are studied: number of early fatalities, number of cases of prodromal vomiting, population dose within 10 mi of the reactor, population dose within 1000 mi of the reactor, individual early fatality probability within 1 mi of the reactor, and maximum early fatality distance. When the predicted variables are considered collectively, the following input variables were found to be the dominant contributors to uncertainty: scaling factor for horizontal dispersion, dry deposition velocity, inhalation protection factor for nonevacuees, groundshine shielding factor for nonevacuees, early fatality hazard function alpha value for bone marrow exposure, and scaling factor for vertical dispersion.
This report summarizes two approaches to time-optimal control of a nonlinear magnetically levitated platen. The system of interest is a candidate technology for next-generation photolithography machines used in the manufacture of integrated circuits. The dynamics and the variable peak control force of the electro-magnetic actuators preclude the direct application of classical time-optimal control methodologies for determining optimal rest-to-rest maneuver strategies. Therefore, this study explores alternate approaches using a previously developed computer simulation. In the first approach, conservative estimates of the available control forces are used to generate suboptimal switching curves. In the second approach, exact solutions are determined iteratively and used as a training set for an artificial neural network. The trained network provides optimal actuator switching times that incorporate the full nonlinearities of the magnetic levitation actuators. Sample problems illustrate the effectiveness of these techniques as compared to traditional proportional-derivative control.
Active control of structures has been under intensive development for the last ten years. Reference 2 reviews much of the identification and control technology for structural control developed during this time. The technology was initially focused on space structure and weapon applications; however, recently the technology is also being directed toward applications in manufacturing and transportation. Much of this technology focused on multiple-input/multiple-output (MIMO) identification and control methodology because many of the applications require a coordinated control involving multiple disturbances and control objectives where multiple actuators and sensors are necessary for high performance. There have been many optimal robust control methods developed for the design of MIMO robust control laws; however, there appears to be a significant gap between the theoretical development and experimental evaluation of control and identification methods to address structural control applications. Many methods have been developed for MIMO identification and control of structures, such as the Eigensystem Realization Algorithm (ERA), Q-Markov Covariance Equivalent Realization (Q-Markov COVER) for identification; and, Linear Quadratic Gaussian (LQG), Frequency Weighted LQG and H-/ii-synthesis methods for control. Upon implementation, many of the identification and control methods have shown limitations such as the excitation of unmodelled dynamics and sensitivity to system parameter variations. As a result, research on methods which address these problems have been conducted.
This paper describes numerical simulations that were performed to study laminar flow through a square duct with a 900 bend. The purpose of this work was two fold. First, an improved understanding was desired of the flow physics involved in the generation of secondary vortical flows in three-dimensions. Second, adaptive gridding techniques for structured grids in three- dimensions were investigated for the purpose of determining their utility in low Reynolds number, incompressible flows. It was also of interest to validate the commercial computer code CFD-ACE. Velocity predictions for both non-adaptive and adaptive grids are compared with experimental data. Flow visualization was used to examine the characteristics of the flow though the curved duct in order to better understand the viscous flow physics of this problem. Generally, moderate agreement with the experimental data was found but shortcomings in the experiment were demonstrated. The adaptive grids did not produce the same level of accuracy as the non-adaptive grid with a factor of four more grid points.
A series of experiments was conducted to determine hydrogen combustion behavior under conditions of rapidly condensing steam caused by water sprays. Experiments were conducted in the Surtsey facility under conditions that were nearly prototypical of those that would be expected in a severe accident in the CE System 80+ containment. Mixtures were initially nonflammable owing to dilution by steam. The mixtures were ignited by thermal glow plugs when they became flammable after sufficient steam was removed by condensation caused by water sprays. No detonations or accelerated flame propagation was observed in the Surtsey facility. The combustion mode observed for prototypical mixtures was characterized by multiple deflagrations with relatively small pressure rises. The thermal glow plugs were effective in burning hydrogen safely by igniting the gases as the mixtures became marginally flammable.
This report identifies the key features noted as requirements in the diagnostic decision-making process of Single Photon Emission Computed Tomography (SPECT) cardiac imaging. The report discusses the critical issues that create the basic system framework for design of an automatic target recognizer (ATR) algorithm prototype to support diagnosis of coronary artery disease. Candidate feature discovery algorithms that may form the basis of future work include Adaptive Resonance Theory and Bayesian Decision Network. A framework for the practitioner-Human-System-Interface would include baseline patient history and demographic data; reference cardiac imagery history; and current overlay imagery to provide complementary information (i.e., coronary angiography, echocardiography, and SPECT images). The goal is to design a prototype that would represent a fused present and historical {open_quotes}whole{close_quotes} functional, structural, and physiologic cardiac patient model. This framework decision-assisting platform would be available to practitioner and student alike, with no {open_quotes}real-world{close_quotes} consequences.
This report describes the process used by Sandia National Laboratories, New Mexico to characterize weapon hardware for disposition. The report describes the following basic steps: (1) the drawing search process and primary hazard identification; (2) the development of Disassembly Procedures (DPs), including demilitarization and sanitization requirements; (3) the generation of a ``disposal tree``; (4) generating RCRA waste disposal information; and (5) documenting the information. Additional data gathered during the characterization process supporting hardware grouping and recycle efforts is also discussed.
Supercomputing `94, a high-performance computing and communications conference, was held November 14th through 18th, 1994 in Washington DC. For the past four years, Sandia National Laboratories has used this conference to showcase and focus its communications and networking endeavors. At the 1994 conference, Sandia built a Switched Multimegabit Data Service (SMDS) network running at 44.736 megabits per second linking its private SMDS network between its facilities in Albuquerque, New Mexico and Livermore, California to the convention center in Washington, D.C. For the show, the network was also extended from Sandia, New Mexico to Los Alamos National Laboratory and from Sandia, California to Lawrence Livermore National Laboratory. This paper documents and describes this network and how it was used at the conference.
The interstitial oxygen (O{sub i}) concentration in Czochralski silicon and the subsequent SiO{sub x} precipitation are important parameters for integrated circuit fabrication. Uncontrolled SiO{sub x} precipitation during processing can create detrimental mechanical and electrical effects that contribute to poor performance. An inability to consistently and accurately measure the initial O{sub i} concentration in heavily doped silicon has led to contradictory results regarding the effects of dopant type and concentration on SiO{sub x} precipitation. The authors have developed a software package for reliably determining and comparing O{sub i} in heavily doped silicon. The SiFTIR{copyright} code implements three independent oxygen analysis methods in a single integrated package. Routine oxygen measurements are desirable over a wide range of silicon resistivities, but there has been confusion concerning which of the three numerical methods is most suitable for the low resistivity portion of the continuum. A major strength of the software is an ability to rapidly produce results for all three methods using only a single Fourier Transform Infrared Spectroscopy (FTIR) spectrum as input. This ability to perform three analyses on a single data set allows a detailed comparison of the three methods across the entire range of resistivities in question. Integrated circuit manufacturers could use the enabling technology provided by SiFTIR{copyright} to monitor O{sub i} content. Early detection of O{sub i} using this diagnostic could be beneficial in controlling SiO{sub x} precipitation during integrated circuit processing.
FITTING is a Fortran subroutine that constructs a smooth, generalized four-parameter probability distribution model. It is fit to the first four statistical moments of the random variable X (i.e., average values of X, X{sup 2}, X{sup 3}, and X{sup 4}) which can be calculated from data using the associated subroutine CALMOM. The generalized model is produced from a cubic distortion of the parent model, calibrated to match the first four moments of the data. This four-moment matching is intended to provide models that are more faithful to the data in the upper tail of the distribution. Examples are shown for two specific cases.
Rountree, S.L.K.; Whitehurst, H.O.; Tomlin, E.H.; Restrepo, L.F.; White, J.
This report documents a study (Stage Right Operational Safety Analysis) that was performed to evaluate the effects of new Stage Right operations on the safety of Pantex personnel who perform the operations and maintain the equipment. The primary concern of the evaluation was for personnel safety during Stage Right operations, but operations equipment damage and degradation also were taken into account. This analysis evaluates safety of the work process in the staging of dismantled nuclear weapon pits within the modified Richmond magazines only. This Stage Right Process and Operational Safety Analysis includes the following processes: moving the pelletized drums from the pallet trailer to the pallet turner, staging of pallets and removal of pallets from the magazine, recovery from an incident in a magazine, setting up, opening, and closing a Zone 4 magazine, inventory of pelletized drums in the magazines, transporting pelletized drums from Zone 12 to Zone 4, and maintenance on the shielded lift truck that involves removal of the cab shielding. The analysis includes the following undesirable consequences: injury to personnel, breach of an AL-R8 container, drop of a loaded pallet, damage to equipment, and equipment unreliability.
The development of two new probabilistic accident consequence codes, MACCS and COSYMA, was completed in 1990. These codes estimate the risks presented by nuclear installations based on postulated frequencies and magnitudes of potential accidents. In 1991, the US Nuclear Regulatory Commission (NRC) and the Commission of the European Communities (CEC) began a joint uncertainty analysis of the two codes. The ultimate objective of the joint effort was to develop credible and traceable uncertainty distributions for the input variables of the codes. Expert elicitation was identified as the best technology available for developing a library of uncertainty distributions for the selected consequence parameters. The study was formulated jointly and was limited to the current code models and to physical quantities that could be measured in experiments. Experts developed their distributions independently. To validate the distributions generated for the wet deposition input variables, samples were taken from these distributions and propagated through the wet deposition code model. Resulting distributions closely replicated the aggregated elicited wet deposition distributions. To validate the distributions generated for the dispersion code input variables, samples from the distributions and propagated through the Gaussian plume model (GPM) implemented in the MACCS and COSYMA codes. Project teams from the NRC and CEC cooperated successfully to develop and implement a unified process for the elaboration of uncertainty distributions on consequence code input parameters. Formal expert judgment elicitation proved valuable for synthesizing the best available information. Distributions on measurable atmospheric dispersion and deposition parameters were successfully elicited from experts involved in the many phenomenological areas of consequence analysis. This volume is the first of a three-volume document describing the project.
An ovenized 10 pF standard capacitor was constructed by the National Institute of Standards and Technology (NIST). The dielectric material used as Wuprasil II grade fused silica. This report discusses a temperature coefficient analysis of the capacitor performed at the Primary Standards Laboratory (PSL) of Sandia National Laboratories (SNL). The effects of temperature change on dielectric loss will also be discussed.
A common limitation to performance in data acquisition systems is storage of the collected data. Compressing the data would increase the amount of data that could be stored. However, most compression routines require that the data be collected and analyzed before compression is performed. Also, these compression routines often store the information required for decompression along with the data, thus decreasing the storage available for data. One solution to this problem is to create an encoding tree known to both the encoder and the decoder based on apriori knowledge of the data. Once the tree is created, optimal encoding schemes such as the Huffman algorithm may be used on the data as it is being collected. In this way the data is compressed as each byte is received and there is no overhead associated with storing decompression data. In this paper the idea of using a fixed Huffman tree is explored and the results are compared to a defacto standard in data compression, PKZIP.
Experiments have been conducted with a molten salt loop at Sandia National Laboratories in Albuquerque, NM to resolve issues associated with the operation of the 10MW{sub e} Solar Two Central Receiver Power Plant located near Barstow, CA. The salt loop contained two receiver panels, components such as flanges and a check valve, vortex shedding and ultrasonic flow meters, and an impedance pressure transducer. Tests were conducted on procedures for filling and thawing a panel, and assessing components and instrumentation in a molten salt environment. Four categories of experiments were conducted: (1) cold filling procedures, (2) freeze/thaw procedures, (3) component tests, and (4) instrumentation tests. Cold-panel and -piping fill experiments are described, in which the panels and piping were preheated to temperatures below the salt freezing point prior to initiating flow, to determine the feasibility of cold filling the receiver and piping. The transient thermal response was measured, and heat transfer coefficients and transient stresses were calculated from the data. Freeze/thaw experiments were conducted with the panels, in which the salt was intentionally allowed to freeze in the receiver tubes, then thawed with heliostat beams. Slow thermal cycling tests were conducted to measure both how well various designs of flanges (e.g., tapered flanges or clamp type flanges) hold a seal under thermal conditions typical of nightly shut down, and the practicality of using these flanges on high maintenance components. In addition, the flanges were thermally shocked to simulate cold starting the system. Instrumentation such as vortex shedding and ultrasonic flow meters were tested alongside each other, and compared with flow measurements from calibration tanks in the flow loop.
A dry barrier may be formed by circulating dry air through a soil layer above or below a waste disposal site, thus reducing the soil moisture content to very low values. Drying a horizontal soil layer creates a barrier to vertical water movement in three ways. First, the drying removes water from the system, intercepting water infiltrating down from the surface. Second, drying a soil layer increases its water storage capacity so the soil will tend to retain rather than transmit water. Third, as a soil layer dries, moisture is removed from progressively smaller interstitial pores so that the hydraulic conductivity of the formation (for liquid flow) decreases. For example, the hydraulic conductivity of a typical sand may decrease by three orders of magnitude as its moisture content is reduced from 20 to 10 percent. This study analyzed the technical and economic feasibility of the subsurface dry barrier concept for containment of a migrating contaminant plume in unsaturated soil. The concept was shown to be a viable option for limiting aqueous migration of pollutants through unsaturated media, with estimated capital costs of between $130,000 and $260,000 for a 1-hectare barrier, and annual operating costs of $10,000 per year.
As photovoltaic (PV) systems gain more acceptance in utility-interactive applications throughout the world, many organizations are placing increasingly higher priorities on writing guidelines, codes and standards. These guidelines and codes are being written to improve safety, installation, acceptance, listing or certification of the PV components or systems. Sandia National Laboratories` PV System Applications Department is working closely with the PV industry to address issues that are associated with fire and personnel safety and with National Electrical Code (NEC) requirements. Additionally, the United States has agreed to participate in two of the International Energy Agency (IEA) Annexes (topical tasks) of the Implementing Agreement for a Cooperative Programme on Photovoltaic Power Systems. This paper describes events and activities associated with the NEC and the IEA that are being led by Sandia National Laboratories with broad participation by the US PV industry.
A method is reported for generating mechanical spacecraft propulsion from unsymmetrical magnetic induction fields. It is based on an unsymmetrical three-dimensional loop antenna structure driven by a repetitively-pulsed high-current power supply. Antenna geometry is optimized for generating propulsive thrust rather than radiating electromagnetic energy. Part of this antenna consists of flat electrical conductors, which form a partially-closed quasi-cylindrical volume around a center conductor. Magnetic flux concentrates at the closed end of the quasicylindrical volume thereby creating a magnetic field flux density gradient along a single axis collinear to the Center Conductor. This magnetic field density gradient imbalances the magneto-mechanical forces that result from the interactions of the internal magnetic induction field with the current in the conductors of the antenna structure, in accordance with Lorentz`s Force Law. Also, there are electrically isolated prismatic conductor surfaces attached to the inside surface of the flat conductors which form the closed end of the quasi-cylindrical volume. Mechanical pressures occur on these conductor prisms because of the changing internal magnetic field and are a consequence of Faraday`s Induction Law and Lenz`s Law. Input current rise time and wave shape are crucial to maximizing spacecraft propulsive thrust.
The Department of Energy is conducting an ongoing investigation of the consequences of taking fuel burnup into account in the design of spent fuel transportation packages. A series of experiments, collectively called the Spent Fuel Safety Experiment (SFSX), has been devised to provide integral benchmarks for testing computer-generated predictions of spent fuel behavior. A set of experiments is planned in which sections of unirradiated fuel rods are interchanged with similar sections of spent PWR fuel rods in a critical assembly. By determining the critical size of the arrays, one can obtain benchmark data for comparison with criticality safety calculations. The integral reactivity worth of the spent fuel can be assessed by comparing the measured delayed critical fuel loading with and without spent fuel. An analytical effort to model the experiments and anticipate the core loadings required to yield the delayed critical conditions runs in parallel with the experimental effort.
The chemical inertness and high bond strengths of the 3-5 nitrides lead to slower plasma etching rates than for more conventional 3-5 semiconductors under the same conditions. High ion density conditions (greater than 3 x 10(exp 11) cm(exp {minus}3)) such as those obtained in ECR or magnetron reactors produce etch rates up to an order of magnitude higher than for RIE, where the ion densities are in the 10(exp 9) cm(exp {minus}3) range. The authors have developed smooth anisotropic dry etches for GaN, InN, AlN and their alloys based on Cl2/CH4/H2/Ar, BCl3/Ar, Cl2/H2, Cl2/SF6, HBr/H2 and HI/H2 plasma chemistries achieving etch rates up to approx. 4,000 A/min at moderate dc bias voltages (less than or equal to {minus}150 V). Ion-induced damage in the nitrides appears to be less apparent than in other 3-5`s. One of the key remaining issues is the achievement of high selectivities for removal of one layer from another.
Quantum well microdisk laser structures have been fabricated in the GaN/InGaN, GaAs/AlGaAs and GaAs/InGaP systems using a combination of ECR dry etching Cl2/CH4/H2/Ar, BCl3/Ar or CH4/H2/Ar plasma chemistries respectively, and subsequent wet chemical etching of a buffer layer underlying the quantum wells. While wet etchants such as HF/H2O and HCl/HNO3/H2O are employed for AlGaAs and InGaP, respectively, a new KOH based solution has been developed for AlN which is completely selective over both GaN and InGaN. Typical mask materials include PR or SiN(x), while the high surface recombination velocity of exposed AlGaAs (approximately) 10(exp 5)cm(center dot)/sec requires encapsulation with ECR-CVD SiN(x) to stabilize the optical properties of the modulators.
This [updated 1/95] report outlines the technology of modern solar central receiver power plants, showing how they could be an important domestic source of energy within the next decade
The microstructure of Al/{alpha}-Al{sub 2}0{sub 3} composites made by infiltrating Al into dense mullite preforms has been characterized using transmission electron microscopy. Observations revealed that the formation of the Al/Al{sub 2}0{sub 3} composites involves three stages. Initially, Al infiltrates into a dense mullite preform through grain boundary diffusion, and reacts with mullite at grain boundaries to form a partial reaction zone. Then, a complete reaction takes place in the reaction region between the partial reaction zone and the full reaction zone to convert the dense mullite preform to a composite of {alpha}-Al{sub 2}0{sub 3} (matrix) and an Al-Si phase (thin channels). Finally, the reduced Si from the reaction diffuses out of the Al/Al{sub 2}0{sub 3} composite through the metal channels, whereas Al from the molten Al pool is continuously drawn to the reaction region until the mullite preform is consumed or the sample is removed from the molten Al pool. Based on the observed microstructure, infiltration mechanisms have been discussed, and a growth model of the composites is proposed in which the process involves repeated nucleation of Al{sub 2}0{sub 3} grains and grain growth.
Copper chemical vapor deposition using liquid coinjection of the Cu(I) precursor (hfac)Cu(TMVS) along with TMVS has been demonstrated. The coinjection of TMVS with (hfac)Cu(TMVS) stabilizes the Cu precursor until it enters the reaction chamber, allowing for better control of the deposition and faster deposition rates. Using this technique, we have grown films with as-deposited resistivities of 1.86 {plus_minus} 0.04 {mu}{Omega}-cm, independent of film thickness. Deposition rates of well over 100 nm/min are possible. Good step coverage and gap fill down to 0.6 {mu}m lines is demonstrated, with gap fill being limited by the large Cu grain sizes in these films.
Very highly porous (aerogel) silica films with refractive index in the range 1.006--1.05 (equivalent porosity 98.5--88%) were prepared by an ambient-pressure process. It was shown earlier using in situ ellipsometric imaging that the high porosity of these films was mainly attributable to the dilation or `springback` of the film during the final stage of drying. This finding was irrefutably reconfirmed by visually observing a `springback` of >500% using environmental scanning electron microscopy (ESEM). Ellipsometry and ESEM also established the near cent per cent reversibility of aerogel film deformation during solvent intake and drying. Film thickness profile measurements (near the drying line) for the aerogel, xerogel and pure solvent cases are presented from imaging ellipsometry. The thickness of these films (crack-free) were controlled in the range 0.1-3.5 {mu}m independent of refractive index.