Publications

Results 96701–96725 of 100,993

Search results

Jump to search filters

Traditional vs. Wev style guides: How do they differ?

Ratner, J.

This paper describes a study in which Web style guides were characterized, compared to traditional human-computer interface (HCI) style guides, and evaluated against findings from HCI reviews of web pages and applications. Findings showed little consistency among the 21 Web style guides assessed, with 75% of recommendations appearing in only one style guide. While there was some overlap, only 20% of Web-relevant recommendations from traditional style guides were found in Web style guides. Web style guides emphasized common look and feel, information display, and navigation issues, with little mention of many issues prominent in traditional style guides such as help, message boxes, and data entry. This difference is reinforced by other results showing that Web style guides address Web information-only pages with much greater success than web-based control enabling features, like buttons and entry fields. It is concluded that while the WWW represents a unique graphical user interface (GUI) environment, development of Web style guides has been less rigorous, with issues associated with web-based control enabling features neglected.

More Details

Electrical test structures replicated in silicon-on-insulator material

Sniegowski, Jeffry J.

Measurements of the linewidths of submicrometer features made by different metrology techniques have frequently been characterized by differences of up to 90 nm. The purpose of the work reported here is to address the special difficulties that this phenomenon presents to the certification of reference materials for the calibration of linewidth-measurement instruments. Accordingly, a new test structure has been designed, fabricated, and undergone preliminary tests. Its distinguishing characteristics are assured cross-sectional profile geometries with known side-wall slopes, surface planarity, and compositional uniformity when it is formed in mono-crystalline material at selected orientations to the crystal lattice. To allow the extraction of electrical linewidth, the structure is replicated in a silicon film of uniform conductivity which is separated from the silicon substrate by a buried oxide layer. The utilization of a Silicon-On-Insulator (SKI) substrate further allows the selective removal of substrate material from local regions below the reference features, thus facilitating measurements by optical and electron-beam transmission microscopy. The combination of planar feature surfaces having known side-wall slopes is anticipated to eliminate factors which are believed to be responsible for methods divergence in linewidth measurements, a capability which is a prerequisite for reliable certification of the linewidths of features on reference materials.

More Details

Evaluation of aqueous cleaners as alternatives to vapor degreasing

Guidotti, Ronald A.

As part of the preparation process during assembly of thermally activated batteries, the stainless steel piece parts are normally cleaned by vapor degreasing with trichloroethylene. Severe restrictions on the use of chlorinated and fluorinated hydrocarbons in recent years prompted the evaluation of a number of aqueous cleaners as a replacement technology for this application. A total of seven commercial aqueous degreasers was evaluated in this study at several dilution ratios and temperatures. One organic cleaner was also examined under ambient conditions. The effectiveness of the cleaner was determined by the use of x-ray photoelectron spectroscopy (XPS), which is a surface analytical technique that is very sensitive to low levels of surface contaminants. A quartz-crystal microbalance (QCM) that is immersed in the cleaning bath was evaluated as a tool for monitoring the bath cleanliness. The best overall cleaning results were obtained with Micro, Impro-Clean 3800, and Sonicor cleaners.

More Details

Extraction of modal parameters with the aid of predicted analytical mode shapes

Mayes, Randall L.

The extraction of the modal parameters for closely spaced modes in the frequency domain is a common problem. However, it is made more difficult if the damping for the closely spaced modes is high. Data from a structure with more than three percent viscous damping is presented which exhibits this phenomenon. Traditional experimental techniques failed to identify all the modal parameters of three closely spaced modes. Mode shapes from an analytical model are manipulated to produce a modal filter which is used to calculate enhanced frequency response functions from which the modal parameters can be more readily identified. Discussion of the advantages and disadvantages of this technique as compared with traditional frequency response function enhancement techniques will be presented.

More Details

Alkaline oxide conversion coatings for aluminum alloys

Buchheit, R.G.

Three related conversion coating methods are described that are based on film formation which occurs when aluminum alloys are exposed to alkaline Li salt solutions. Representative examples of the processing methods, resulting coating structure, composition and morphology are presented. The corrosion resistance of these coatings to aerated 0.5 M NaCl solution has been evaluated as a function of total processing time using electrochemical impedance spectroscopy (EIS). This evaluation shows that excellent corrosion resistance can be uniformly achieved using no more than 20 minutes of process time for 6061-T6. Using current methods a minimum of 80 minutes of process time is required to get marginally acceptable corrosion resistance for 2024-T3. Longer processing times are required to achieve uniformly good corrosion resistance.

More Details

Report on the treatability study for inerting small quantities of radioactive explosives and explosive components

Loyola, V.M.

As a result of Sandia`s radiation hardening testing on a variety of its explosive components, radioactive waste streams were generated and have to be disposed of as radioactive waste. Due to the combined hazards of explosives and radioactivity, Sandia`s Radioactive and Mixed Waste Management organization did not have a mechanism for disposal of these waste streams. This report documents the study done to provide a method for the removal of the explosive hazard from those waste streams. The report includes the design of the equipment used, procedures followed, results from waste stream analog tests and the results from the actual explosive inerting tests on radioactive samples. As a result of the inerting treatment, the waste streams were rendered non-explosive and, thus, manageable through normal radioactive waste disposal channels.

More Details

Assessment of molten-salt solar central-receiver freeze-up and recovery events

Pacheco, James E.

Molten salt used as a heat transfer fluid in central-receiver so ar power plants has a high freezing point (430{degrees}F (221{degrees}C)). It is very likely during the life of the plant that the receiver will accidentally freeze up due to equipment malfunction or operator error. Experiments were conducted to measure the effects of a molten salt receiver freeze-up and recovery event and methods to thaw the receiver. In addition, simulated freeze/thaw experiments were conducted to determine what happens when salt freezes and is thawed in receiver tubes and to quantify the damage caused to candidate receiver tube materials. Fourteen tube samples of various materials, diameters and wall thicknesses were tested to destruction. Results of these tests are presented in this paper.

More Details

Smooth, low-damage, definition of InGaAlAs asymmetric Fabry-Perot optical transmission modulators by Cl{sub 2}+Ar reactive-ion-beam etching

Vawter, G.A.; Fritz, I.J.; Drummond, T.J.; Lee, S.R.; Hafich, M.J.; Howard, A.J.; Briggs, R.D.; Casalnuovo, S.A.; Griego, L.

Chlorine-argon-based reactive-ion-beam etching was used successfully to etch novel InGaAlAs (1.32 {mu}m-wavelength Fabry-Perot resonator transmission) modulators. Resulting etch is very smooth, anisotropic, and has low etch-induced (sidewall) damage. Use of this simple chemistry eliminates difficulties with polymer formation encountered in hydrocarbon-based etches.

More Details

An assessment of simplified methods to determine damage from ship-to-ship collisions

Ammerman, Douglas

Sandia National Laboratories (SNL) is studying the safety of shipping, radioactive materials (RAM) by sea, the SeaRAM project (McConnell, et al. 1995), which is sponsored by the US Department of Energy (DOE). The project is concerned with the potential effects of ship collisions and fires on onboard RAM packages. Existing methodologies are being assessed to determine their adequacy to predict the effect of ship collisions and fires on RAM packages and to estimate whether or not a given accident might lead to a release of radioactivity. The eventual goal is to develop a set of validated methods, which have been checked by comparison with test data and/or detailed finite element analyses, for predicting the consequences of ship collisions and fires. These methods could then be used to provide input for overall risk assessments of RAM sea transport. The emphasis of this paper is on methods for predicting- effects of ship collisions.

More Details

Evaluations of fiber optic sensors for interior applications

Sandoval, Martin

This report addresses the testing and evaluation of commercial fiber optic intrusion detection systems in interior applications. The applications include laying optical fiber cable above suspended ceilings to detect removal of ceiling tiles, embedding optical fibers inside a tamper or item monitoring blanket that could be placed over an asset, and installing optical fibers on a door to detect movement or penetration. Detection capability of the fiber optic sensors as well as nuisance and false alarm information were focused on during the evaluation. Fiber optic sensor processing, system components, and system setup are described.

More Details

Aging management guideline for commercial nuclear power plants - tanks and pools

Blocker, E.; Smith, S.; Philpot, L.; Conley, J.

Continued operation of nuclear power plants for periods that extend beyond their original 40-year license period is a desirable option for many U.S. utilities. U.S. Nuclear Regulatory Commission (NRC) approval of operating license renewals is necessary before continued operation becomes a reality. Effective aging management for plant components is important to reliability and safety, regardless of current plant age or extended life expectations. However, the NRC requires that aging evaluations be performed and the effectiveness of aging management programs be demonstrated for components considered within the scope of license renewal before granting approval for operation beyond 40 years. Both the NRC and the utility want assurance that plant components will be highly reliable during both the current license term and throughout the extended operating period. In addition, effective aging management must be demonstrated to support Maintenance Rule (10 CFR 50.65) activities.

More Details

Development of Aspen: A microanalytic simulation model of the US economy

Pryor, Richard J.

This report describes the development of an agent-based microanalytic simulation model of the US economy. The microsimulation model capitalizes on recent technological advances in evolutionary learning and parallel computing. Results are reported for a test problem that was run using the model. The test results demonstrate the model`s ability to predict business-like cycles in an economy where prices and inventories are allowed to vary. Since most economic forecasting models have difficulty predicting any kind of cyclic behavior. These results show the potential of microanalytic simulation models to improve economic policy analysis and to provide new insights into underlying economic principles. Work already has begun on a more detailed model.

More Details

Capillary flow of solder on chemically roughened PWB surfaces

Hosking, F.M.; Stevenson, J.O.; Yost, F.G.

The Center for Solder Science and Technology at Sandia National Laboratories has developed a solderability test for evaluating fundamental solder flow over PWB (printed wiring boards) surface finishes. The work supports a cooperative research and development agreement between Sandia, the National Center for Manufacturing Sciences (NCMS), and several industrial partners. An important facet of the effort involved the ``engineering`` of copper surfaces through mechanical and chemical roughening. The roughened topography enhances solder flow, especially over very fine features. In this paper, we describe how etching with different chemical solutions can affect solder flow on a specially designed ball grid array test vehicle (BGATV). The effects of circuit geometry, solution concentration, and etching time are discussed. Surface roughness and solder flow data are presented to support the roughening premise. Noticeable improvements in solder wettability were observed on uniformly etched surfaces having relatively steep peak-to-valley slopes.

More Details

Characterization of polyxylylenes with solid state {sup 13}C nuclear magnetic resonance spectroscopy

Loy, Douglas A.

Polyxylylenes are thermoplastics used as encapsulants for electronic devices. Five polyxylylenes were prepared by pyrolysis of [2.2]paracyclophanes and characterized by solid state {sup 13}C NMR spectroscopy. The chemical shift data, in combination with interrupted decoupling experiments, allowed assignment of resonances to their carbon sources in the polymers. This confirmed the integrity of the xylylene building block in the polymers and is consistent with linear polymers. No crosslinking could be detected within the NMR sensitivity limits. Residual paracyclophane was detected by {sup 13}C CP MAS NMR spectroscopy in the polyxylylene samples prepared at room temperature; however discrete {sup 13}C resonances due to amorphous and crystalline phases in the polymers were not resolved.

More Details

Ohmic contacts to Si-implanted and un-implanted n-type GaN

Zolper, J.

We report on ohmic contacts to Si-implanted and un-implanted n-type GaN on sapphire. A ring shaped contact design avoids the need to isolate the contact structures by additional implantation or etching. Metal layers of Al and Ti/Al were investigated. On un-implanted GaN, post metalization annealing was performed in an RTA for 30 seconds in N{sub 2} at 700, 800, and 900 C. A minimum specific contact resistance (r{sub c}) of 1.4{times}10{sup -5} {Omega}{minus}cm{sup 2} was measured for Ti/Al at an annealing temperature of 800 C. Although these values are reasonably low, variations of 95% in specific contact resistance were measured within a 500 {mu}m distance on the wafer. These results are most likely caused by the presence of compensating hydrogen. Specific contact resistance variation was reduced from 95 to 10% by annealing at 900 C prior to metalization. On Si-implanted GaN, un-annealed ohmic contacts were formed with Ti/Al metalization. The implant activation anneal of 1120 C generates nitrogen vacancies that leave the surface heavily n-type, which makes un-annealed ohmic contacts with low contact resistivity possible.

More Details

Parallel CARLOS-3D code development

Kotulski, Joseph D.

CARLOS-3D is a three-dimensional scattering code which was developed under the sponsorship of the Electromagnetic Code Consortium, and is currently used by over 80 aerospace companies and government agencies. The code has been extensively validated and runs on both serial workstations and parallel super computers such as the Intel Paragon. CARLOS-3D is a three-dimensional surface integral equation scattering code based on a Galerkin method of moments formulation employing Rao- Wilton-Glisson roof-top basis for triangular faceted surfaces. Fully arbitrary 3D geometries composed of multiple conducting and homogeneous bulk dielectric materials can be modeled. This presentation describes some of the extensions to the CARLOS-3D code, and how the operator structure of the code facilitated these improvements. Body of revolution (BOR) and two-dimensional geometries were incorporated by simply including new input routines, and the appropriate Galerkin matrix operator routines. Some additional modifications were required in the combined field integral equation matrix generation routine due to the symmetric nature of the BOR and 2D operators. Quadrilateral patched surfaces with linear roof-top basis functions were also implemented in the same manner. Quadrilateral facets and triangular facets can be used in combination to more efficiently model geometries with both large smooth surfaces and surfaces with fine detail such as gaps and cracks. Since the parallel implementation in CARLOS-3D is at high level, these changes were independent of the computer platform being used. This approach minimizes code maintenance, while providing capabilities with little additional effort. Results are presented showing the performance and accuracy of the code for some large scattering problems. Comparisons between triangular faceted and quadrilateral faceted geometry representations will be shown for some complex scatterers.

More Details

Classification of poison inhalation hazard materials into severity groups

Griego, N.R.

Approximately 1.5 billion tons of hazardous materials (hazmat) are transported in the US annually, and most reach their destinations safely. However, there are infrequent transportation accidents in which hazmat is released from its packaging. These accidental releases can potentially affect the health of the exposed population and damage the surrounding environment. Although these events are rare, they cause genuine public concern. Therefore, the US Department of Transportation Research & Special Programs Administration (DOT- RSPA) has sponsored a project to evaluate the protection provided by the current bulk (defined as larger than 118 gallons) packagings used to transport materials that have been classified as Poison Inhalation Hazards (PIH) and recommend performance standards for these PIH packagings. This project was limited to evaluating bulk packagings larger than 2000 gallons. This project involved classifying the PIH into severity categories so that only one set of packaging performance criteria would be needed for each severity category rather than a separate set of performance criteria for each individual PIH. By grouping the PIH into Hazard Zones, Packaging Groups and performance standards for these Hazard Zones can be defined. Each Hazard Zone can correspond to a Packaging Group or, as in 49CFR173 for non-bulk packagings, one Packaging Group may cover more than one Hazard Zone. If the packaging groups are chosen to correspond to the classification categories presented in this report, then the maximum allowable leak rates used to define these categories could be used as the maximum allowable leak rates for the performance oriented packaging standards. The results discussed in this report are intended to provide quantitative guidance for the appropriate authorities to use in making these decisions.

More Details

Stabilization of liquid low-level and mixed wastes: a treatability study

Carson, Susan D.

A treatability study has been conducted on liquid low-level and mixed wastes using the stabilization agents Aquaset, Aquaset II, Aquaset II-H, Petroset, Petroset-H, and Petroset and Petroset II. A total of 40 different waste types with activities ranging from 10{sup {minus}14} to 10{sup {minus}4} curies/ml have been stabilized. Reported data for each waste include its chemical and radiological composition and the optimum composition or range of compositions (weight of agent/volume of waste) for each stabilization agent used. All wastes were successfully stabilized with one or more of the stabilization agents and all final waste forms passed the Paint Filter Liquids Test (EPA Method 9095).

More Details

Chatter suppression through variable impedance and smart fluids

Segalman, Daniel J.

A novel approach to mitigating chatter vibrations in machine tools is presented. Encountered in many types of metal removal processes, chatter is a dangerous condition which results from the interaction of the cutting dynamics with the modal characteristics of the machine-workpiece assembly. Tool vibrations are recored on the surface of the workpiece during metal removal, imposing a waviness which alters the chip thickness during subsequent cutting passes. Deviations from the nominal chip thickness effect changes in the cutting force which, under certain conditions, can further excite vibrations. The chatter mitigation strategy presented is based on periodically altering the impedance of the cutting tool assembly. A cyclic electric (or magnetic) field is applied to the spindle quill which contains an electro-rheological (or magneto-rheological) fluid. The variable yield stress in the fluid affects the coupling of the spindle to the machine tool structure, changing the natural frequency of oscillation. Altering the modal characteristics in this fashion disrupts the modulation of current tool vibrations with previous tool vibrations recorded on the workpiece surface. Results from a simulated milling process reveal that significant reductions in vibration amplitude can be achieved through proper selection of fluid and excitation frequency.

More Details

Micromachined sensor and actuator research at Sandia`s Microelectronics Development Laboratory

Smith, J.H.

An overview of surface micromachining projects at the Microelectronics Development Laboratory of Sandia National Laboratories is presented. Development efforts are underway for a variety of surface micromachined sensors and actuators. A technology that embeds micromechanical devices below the surface of the wafer prior to microelectronics fabrication has also been developed for integrating microelectronics with surface micromachined micromechanical devices.

More Details

Geospatial analyses and system architectures for the next generation of radioactive materials risk assessment and routing

Ganter, John H.

This paper suggests that inexorable changes in the society are presenting both challenges and a rich selection of technologies for responding to these challenges. The citizen is more demanding of environmental and personal protection, and of information. Simultaneously, the commercial and government information technologies markets are providing new technologies like commercial off-the-shelf (COTS) software, common datasets, ``open`` GIS, recordable CD-ROM, and the World Wide Web. Thus one has the raw ingredients for creating new techniques and tools for spatial analysis, and these tools can support participative study and decision-making. By carrying out a strategy of thorough and demonstrably correct science, design, and development, can move forward into a new generation of participative risk assessment and routing for radioactive and hazardous materials.

More Details

Market survey results for alternate sensor communications

Rivas, Raul R.

This document presents the results of a system analysis and market survey of commercially available alarm communication systems for potential use as an alternate sensor communication system. Only those systems that report alarm/sensor information to a central control panel were considered. The communication systems surveyed include wireless radio frequency (RF) systems, spread spectrum systems, fiber optic systems, twisted pair/copper wire, cellular systems, and other types of communication equipment. All systems are commercially available, and most information was obtained by telephone conversations with the manufacturer, personal interviews at security conferences, and countless reviews of the manufacturers` data sheets. Many systems were identified, but only those that met a minimum set of system requirements were included. Other systems that appeared to be applicable usually did not provide adequate data encryption or could not interface directly to the system. While such features could be incorporated using additional hardware, doing so would make the system more expensive and conflict with the idea of purchasing a single unit that meets the minimum set of requirements. Several systems greatly exceed the scope of this project and utilizing such systems would mean investing in more capacity than is really needed.

More Details

Technical findings from Sandia`s intrabuilding recabling project

Adams, Roger L.

The US and other leading nations are at the forefront of a global trend to implement both national and international enterprise networks via information highways. New or upgraded cabling infrastructures are essential to support these activities. Professionals in the telecommunications industry are keenly aware of the challenges presented by such cabling upgrades. Desktop connectivity must be established before quantum leaps in information flow, as suggested by new technologies and global concepts. Some businesses with campus-type facilities have undertaken this formidable challenge. Universities and other higher-level learning institutions, corporate research facilities, independent and government-funded laboratories, financial institutions, medical facilities, and unique suburban housing test sites have risen to this challenge. Sandia National Laboratories is one such organization. This report presents the lessons learned from this project and gives 13 specific recommendations for manufacturers, buyers, and installers.

More Details
Results 96701–96725 of 100,993
Results 96701–96725 of 100,993
Top