Publications

Results 96501–96525 of 100,993

Search results

Jump to search filters

In situ growth rate measurements by normal-incidence reflectance during MOVPE growth

Hou, H.Q.; Breiland, W.G.; Hammons, B.E.; Chui, H.C.

We present an in situ technique for monitoring metal-organic vapor phase epitaxy growth by normal-incidence reflectance. This technique is used to calibrate the growth rate periodically and to monitor the growth process routinely. It is not only a precise tool to measure the growth rate, but also very useful in identifying unusal problems during a growth run, such as depletion of source material, deterioration of surface morphology, and problems associated with an improper growht procedure. We will also present an excellent reproducibility ({+-}0.3% over a course of more than 100 runs) of the cavity wavelength of vertical-cavity surface emitting laser structures with periodic calibration by this in situ technique.

More Details

Electromagnetic effects on transportation systems

Morris, M.E.; Dinallo, M.A.

Electronic and electrical system protection design can be used to eliminate deleterious effects from lightning, electromagnetic interference, and electrostatic discharges. Evaluation of conventional lightning protection systems using advanced computational modeling in conjunction with rocket-triggered lightning tests suggests that currently used lightning protection system design rules are inadequate and that significant improvements in best practices used for electronic and electrical system protection designs are possible. A case study of lightning induced upset and failure of a railway signal and control system is sketched.

More Details

Multiattribute utility analysis as a framework for public participation siting a hazardous waste facility

Conway, R.

How can the public play a role in decisions involving complicated scientific arguments? This paper describes a public participation exercise in which stakeholders used multiattribute utility analysis to select a site for a hazardous waste facility. Key to success was the ability to separate and address the two types of judgements inherent in environmental decisions: technical judgements on the likely consequences of alternative choices and value judgements on the importance or seriousness of those consequences. This enabled technical specialists to communicate the essential technical considerations and allowed stakeholders to establish the value judgements for the decision. Although rarely used in public participation, the multiattribute utility approach appears to provide a useful framework for the collaborative resolution of many complex environmental decision problems.

More Details

Isothermal aging of three polyurethane elastomers

Guess, Tommy R.

Two polyurethane systems, EN-7 and L-100, have a long history as encapsulants and coatings in Sandia programs. These materials contain significant amounts of toluene diisocyanate (TDI), a suspect human carcinogen. As part of efforts to reduce the use of hazardous materials in the workplace, PET-90A, a polyurethane with less than 0.1% free TDI, was identified as a candidate for new applications and as a replacement for the more hazardous polyurethanes in selected programs. This report documents the results of a two-year accelerated aging study of PET-90A, EN-7, and L-100 polyurethane elastomers to characterize the effect of 135{degrees}F isothermal aging on selected physical, electrical, mechanical and thermal properties. In general, there was very little change in properties over the two year period for the three elastomers. The largest changes occurred in EN-7, which is the polyurethane with the longest service history in Sandia applications.

More Details

Vector network analyzer check standards measurements and database software

Duda, L.E.

Vector network analyzers provide a convenient way to measure scattering parameters of a variety of microwave devices. However, these instruments, unlike oscilloscopes, require a high degree of user knowledge and expertise. Measurement calibration or error correction must be done prior to use. There are many ways to make poor measurement or measurement. Check standards have been used to verify that the network analyzer is operating properly. A computer program was developed to automatically measure a check standard and compare the new measurements with an historical database of measurements of the check standard device. The program can acquire new measurement data from selected check standards, plot the new data against the mean and standard deviation of prior data for the check standard, and update the database files for the check standard. This paper describes the function of the software including a discussion of its capabilities. The way in which the software is used in our lab is also described. Finally, examples are given of how the software can detect potential measurement problems.

More Details

Combustion of Bulk 84% Fe/16% KCIO{sub 4} heat powder

Guidotti, Ronald A.

Fe/KClO{sub 4} pyrotechnic mixtures are used in thermal batteries to provide the heat necessary to bring the battery stack to operating temperatures of 550 to 600 C. This heat source is normally used as discs pressed from bulk powder. To evaluate the consequences associated with unexpected ignition of large amounts of heat powder, combustion of 84% Fe/16% KClO{sub 4} heat powders was conducted for various scenarios under controlled conditions and the response documented. Increasing amounts of heat powder--up to 8 lbs--were ignited in both unconfined and confined (sealed) containers in a remote area. The containers were thermocoupled and the resulting burning filmed with a standard video camera, high-speed (1,000 frames/s) film and video cameras, and an infrared video camera. A 20- minute video of the burning under the various conditions is presented.

More Details

Integrated Safety, Environmental, & Emergency Management Systems (ISEEMS)

Silver, R.

Sandia`s Risk Management and NEPA Department recognized the need for hazard and environmental data analysis and management to support the line managers` need to know, understand, manage and document the hazards inherent in their facilities and activities. ISEEMS (Integrated Safety, Environmental, & Emergency Management System) was developed in response to this need. ISEEMS takes advantage of the fact that there is some information needed for the NEPA process that is also needed for the safety documentation process. The ISEEMS process enables Sandia to identify and manage hazards and environmental concerns at a level of effort commensurate with the hazards themselves by adopting a necessary and sufficient (graded) approach to compliance. The Preliminary Hazard Screening module of ISEEMS determines the facility or project activity hazard classification and facility designation. ISEEMS` geo-referenced icon allows immediate, visual integration of hazard information across geographic boundaries resulting in significant information compression. At Sandia, ISEEMS runs on the Sandia Internal Restricted Network, in an MS-Windows environment on standard PC hardware. The possibility of transporting ISEEMS to a ``WEB-like`` environment is being explored.

More Details

Integrated environmental, health and safety management; The outcome of the `Necessary and Sufficient Process`

Bendure, Albert

This paper presents a paradigm for integrating the many facets of ES&H management based on the necessary and sufficient control of hazards and the resulting risks through a systems approach. The paradigm answers the question ``What is the best approach to managing ES&H to increase value, reduce risk, and improve satisfaction?`` Hazard identification is the foundation of integrated ES&H management. Knowledge of risk is essential to the necessary and sufficient management of risk. A systems approach to identifying and managing risks is essential in achieving integrated ES&H management. Feedback is discussed. The objectives can be applied to the function of risk management using the ``Know, Understand, Manage and Document`` paradigm. The organizational structure is crucial to the success of integrated ES&H management.

More Details

Potential power sources for high-temperature geothermal applications

Guidotti, Ronald A.

The thermal response under geothermal-borehole conditions of a conventional thermal battery was evaluated for various designs by numerical simulations using a finite-element thermal model. This technology, which is based on molten salts, may be suitable as a power source for geothermal borehole applications for data logging. Several promising candidate electrolytes were identified for further study.

More Details

Evaluation of constitutive models for crushed salt

Callahan, G.D.; Loken, M.C.; Hurtado, L.D.; Hansen, F.D.

Three constitutive models are recommended as candidates for describing the deformation of crushed salt. These models are generalized to three-dimensional states of stress to include the effects of mean and deviatoric stress and modified to include effects of temperature, grain size, and moisture content. A database including hydrostatic consolidation and shear consolidation tests conducted on Waste Isolation Pilot Plant (WIPP) and southeastern New Mexico salt is used to determine material parameters for the models. To evaluate the capability of the models, parameter values obtained from fitting the complete database are used to predict the individual tests. Finite element calculations of a WIPP shaft with emplaced crushed salt demonstrate the model predictions.

More Details

Selective, pulsed CVD of platinum on microfilament gas sensors

Manginell, R.P.; Smith, J.H.; Ricco, A.J.; Moreno, D.J.; Hughes, R.C.; Huber, R.J.; Senturia, S.D.

A post-processing, selective micro-chemical vapor deposition (``micro-CVD``) technology for the deposition of catalytic films on surface-micromachined, nitride-passivated polysilicon filaments has been investigated. Atmospheric pressure deposition of Pt on microfilaments was accomplished by thermal decomposition of Pt acetylacetonate; deposition occurs selectively only on those filaments which are electrically heated. Catalyst morphology, characterized by SEM, can be controlled by altering deposition time, filament temperature, and through the use of pulsed heating of the filament during deposition. Morphology plays an important role in determining the sensitivity of these devices when used as combustible gas sensors.

More Details

Characterization of semiconductor bridges (SCB) igniters for use in thermal batteries

Bickes, R.W.; Guidotti, R.A.; Mccampbell, C.B.

Semiconductor bridges (SCB) igniters were evaluated as possible replacements for conventional hot-wire igniters for use in thermal batteries. The all-fire and no-fire characteristics were determined using an up-down scheme; the Neyer/SENSIT program was used to analyze the data. The SCB igniters functioned with a higher no-fire level, relative to a hot-wire igniter, for a given all-fire level. This makes the SCB igniter safer and more reliable than its hot-wire counterpart. The SCB is very resistant to electrostatic discharge and does not require a sensitization mixture for ignition of the primary pyrotechnic charge. These factors, along with its amenability to large-scale production, make the SCB igniter ideally suited for use in thermal batteries.

More Details

Application of chemical-mechanical polishing to planarization of surface-micromachined devises

Nasby, R.D.

Chemical-Mechanical Polishing (CMP) has emerged as an enabling technology for manufacturing multi-level metal interconnects used in high-density Integrated Circuits (IC). In this work we present extension of CMP from sub-micron IC manufacturing to fabrication of complex surface-micromachined Micro-ElectroMechanical Systems (MEMS). This planarization technique alleviates processing problems associated with fabrication of multi-level polysilicon structures, eliminates design constraints linked with non-planar topography, and provides an avenue for integrating different process technologies. We discuss the CMP process and present examples of the use of CMP in fabricating MEMS devices such as microengines, pressures sensors, and proof masses for accelerometers along with its use for monolithically integrating MEMS devices with microelectronics.

More Details

Three dimensional finite element simulations of room and pillar mines in rock salt

Hoffman, Edward L.

3-D quasistatic finite element codes are being used at Sandia to simulate large room and pillar mines in rock salt. The two examples presented in this paper are of mines supported by US DOE, under the auspices of the Strategic Petroleum Reserve program. One of the mines is presently used as an oil storage facility. These simulations, validated by field measurements and observations, have provided valuable insight into the failure mechanisms of room and pillar mines in rock salt. The calculations provided the basis for further investigation and the ultimate decision to decommission the DOE oil storage facility.

More Details

Large-scale dynamic compaction of natural salt

Hansen, Francis D.

A large-scale dynamic compaction demonstration of natural salt was successfully completed. About 40 m{sup 3} of salt were compacted in three, 2-m lifts by dropping a 9,000-kg weight from a height of 15 m in a systematic pattern to achieve desired compaction energy. To enhance compaction, 1 wt% water was added to the relatively dry mine-run salt. The average compacted mass fractional density was 0.90 of natural intact salt, and in situ nitrogen permeabilities averaged 9X10{sup -14}m{sup 2}. This established viability of dynamic compacting for placing salt shaft seal components. The demonstration also provided compacted salt parameters needed for shaft seal system design and performance assessments of the Waste Isolation Pilot Plant.

More Details

Issues in workforce composition analysis

Rogers, J.D.

An issue of paramount interest to US industry is the supply and quality of human resources available for this country`s scientific and technological activities. The changing composition of the workforce and the responsibility that an organization has to assure equal opportunity, give rise to various issues. This paper discusses some of the issues associated with the scientific and technical workforce. Specifically, it explores some of the questions pertaining to workforce composition and measures of workforce composition. This paper should be useful to those responsible for personnel policies.

More Details

Constitutive basis of the MDCF model for rock salt

Fossum, Arlo F.

All valid constitutive equations must satisfy two general invariance principles as well several other principles. In this paper the MDCF (Multimechanism Deformation Coupled Fracture) model for rock salt is shown to be thermodynamically consistent, coordinate invariant, frame indifferent, and physically admissible. Additionally, the stress rates used in the formulation are shown to be kinematically consistent with the Cauchy stress rates.

More Details

Screening study of mixed transition-metal oxides for use as cathodes in thermal batteries

Guidotti, Ronald A.

Over 100 candidates were examined, including commercial materials and many that were synthesized in house. The mixed oxides were based on Ti, V, Nb, Cr, Mo, W, Mn, Fe, Co, Ni, and Cu doped with other transition metals. A number of individual (single-metal) oxides were included for comparison. The candidates were tested in single cells with Li(Si) anodes and separators based on LiCl-KCl eutectic. Screening was done under constant-current conditions at current densities of 125 me/cm{sup 2} and, to a lesser extent, 50 me/cm{sup 2} at 500 C. Relative performance and limitations of the oxide cathodes are discussed.

More Details

Phase 2 report on the evaluation of polyacrylonitrile (PAN) as a binding polymer for absorbers used to treat liquid radioactive wastes

Matalucci, R.V.

The performance of PAN-based composite absorbers was evaluated in dynamic experiments at flow rates ranging from 25--100 bed volumes (BV) per hour. Composite absorbers with active components of ammonium molybdophosphate (AMP) PAN and K-Co ferrocyanide (KCoFC) PAN were used for separating Cs from a 1 M HNO{sub 3} + 1 M NaNO{sub 3} + 2 {times} 10{sup {minus}5} M CsCl acidic simulant solution. KCoFC-PAN and two other FC-based composite absorbers were tested for separating Cs from alkaline simulant solutions containing 0.01 M to 1 M NaOH and 1 M NaNO{sub 3} + x {times} 10{sup {minus}4} M CsCl. The efficiency of the Cs sorption on the AMP-PAN absorber from acidic simulant solutions was negatively influenced by the dissolution of the AMP active component. At flow rates of 50 BV/hr, the decontamination factor of about 10{sup 3} could be maintained for treatment of 380 BV of the feed. With the KCoFC-PAN absorber, the decontamination factor of about 10{sup 3} could be maintained for a feed volume as great as 1,800 BV. In alkaline simulant solutions, significant decomposition of the active components was observed, and the best performance was exhibited by the KCoFC-PAN absorber. Introductory experiments confirmed that Cs may be washed out of the composite absorbers. Regeneration of both absorbers for repetitive use was also found to be possible. The main result of the study is that PAN was proven to be a versatile polymer capable of forming porous composite absorbers with a large number of primary absorbers. The composite absorbers proved to be capable of withstanding the harsh acidic and alkaline conditions and significant radiation doses that may be expected in the treatment of US DOE wastes. A field demonstration is proposed as a follow-on activity.

More Details

Lessons-learned from the document production system redevelopment (DPS/R)

Rouse, M.J.

Increased complexity of the computing environment is probably the most universal observation of developers going into Client/Server computing. The Lessons Learned document Provides some condensed bits of expertise gained by the Document Production System Redevelopment team. The intent is to distribute in a simplified format the knowledge the authors have gained, and to promote discussion of certain areas having unresolved or less-than-perfect resolution. Included are first, a description of the hardware and software used. The lists of hardware and software are a good basic guide for the components of a robust data server and provide a framework for subsequent discussion of technical points learned during the development. The second part of the document is a discussion of fine points about Novell, Sybase and Visual Basic as applied to the DPS/R development. Areas covered include the hardware of the database server, Novell operating system, Sybase database tools and Visual Basic.

More Details

Effect of hydrogen on Ca and Mg acceptors in GaN

Zolper, J.C.

The influence of minority carrier injection on the reactivation of hydrogen passivated Mg in GaN at 175 C has been investigated in p-n junction diodes. The dissociation of the neutral MgH complexes is greatly enhanced in the presence of minority carrier and the reactivation process follows second order kinetics. Conventional annealing under zero-bias conditions does not produce Mg-H dissociation until temperatures {ge} 450 C. These results provide an explanation for the e-beam induced reactivation of Mg acceptors in hydrogenated GaN. Exposure to a hydrogen plasma at 250 C of p-type GaN (Ca) prepared by either Ca{sup +} or Ca{sup +} plus P{sup +} coimplantation leads to a reduction in sheet carrier density of approximately an order of magnitude (1.6 {times} 10{sup 12} cm{sup {minus}2} to 1.8 {times} 10{sup 11} cm{sup {minus}2}), and an accompanying increase in hole mobility (6 cm{sup 2}/Vs to 18 cm{sup 2}/Vs). The passivation process can be reversed by post-hydrogenation annealing at 400--500 C under a N{sub 2} ambient. This reactivation of the acceptors is characteristic of the formation of neutral (Ca-H) complexes in the GaN. The thermal stability of the passivation is similar to that of Mg-H complexes in material prepared in the same manner (implantation) with similar initial doping levels. Hydrogen passivation of acceptor dopants in GaN appears to be a ubiquitous phenomenon, as it is in other p-type semiconductors.

More Details

Ion implantation in compound semiconductors for high-performance electronic devices

Zolper, J.C.

Advanced electronic devices based on compound semiconductors often make use of selective area ion implantation doping or isolation. The implantation processing becomes more complex as the device dimensions are reduced and more complex material systems are employed. The authors review several applications of ion implantation to high performance junction field effect transistors (JFETs) and heterostructure field effect transistors (HFETs) that are based on compound semiconductors, including: GaAs, AlGaAs, InGaP, and AlGaSb.

More Details

Garnet phosphors prepared via hydrothermal synthesis

Phillips, Mark L.F.

This project studied hydrothermal synthesis as a route to producing green-emitting cathodoluminescent phosphorus isostructural with yttrium aluminum garnet (Y{sub 3}Al{sub 5}O{sub 12}, or YAG). Aqueous precipitation of Y, Gd, Al, Ga, and Tb salts produced amorphous gels, which were heated with water at 600 C and 3,200 bar to produce crystalline YAG:Tb, Y{sub 3}Ga{sub 5}O{sub 12}:Tb, Y{sub 3}Al{sub 3}Ga{sub 2}O{sub 12}:Tb, and Gd{sub 3}Ga{sub 5}O{sub 12}:Tb powders. Process parameters were identified that yielded submicron YAG:Tb and Y{sub 3}Ga{sub 5}O{sub 12}:Tb powders without grinding. Cathodoluminescent efficiencies were measured as functions of power density at 600 V, using both the hydrothermal garnets and identical phosphor compositions synthesized at high temperatures. Saturation behavior was independent of synthetic technique, however, the hydrothermal phosphorus were less susceptible to damage (irreversible efficiency loss) at very high power densities (up to 0.1 W/cm{sup 2}). The fine grain sizes available with hydrothermal synthesis make it an attractive method for preparing garnet phosphorus for field emission, projection, and head-up displays.

More Details

Laser Engineered Net Shaping (LENS{trademark}) for additive component processing

Keicher, David

Sandia National Laboratories is presently developing an additive component processing technology called Laser Engineered Net Shaping, (LENS{trademark}). This process allows complex 3-dimensional solid metallic objects to be directly fabricated from a CAD solid model. Currently, this process functions similar to the Stereo Lithography process in which a faceted file is generated from the CAD solid model and then sliced into a sequence of layers. The sliced file is then input into another interpreter program which converts the sliced file into a series of tool path patterns required to build the entire layer. The component is fabricated by first generating an outline of the key component features and then filled using a rastering technique. This file is then used to drive the laser system to produce the desired component one layer at a time. This process differs from present rapid prototyping (RP) processes in that a fully dense, metallic component can be produced using this process.

More Details

The growth and doping of Al(As)Sb by metal-organic chemical vapor deposition

Biefeld, Robert M.

AlSb and AlAs{sub x}Sb{sub 1{minus}x} epitaxial films grown by metal-organic chemical vapor deposition were successfully doped p- or n-type using diethylzinc or tetraethyltin, respectively. AlSb films were grown at 500 C and 76 torr using trimethylamine or ethyldimethylamine alane and triethylantimony. The authors examined the growth of AlAsSb using temperature of 500 to 600 C, pressures of 65 to 630 torr, V/III ratios of 1--17, and growth rates of 0.3 to 2.7 {micro}m/hour in a horizontal quartz reactor. SIMS showed C and O levels below 2 {times} 10{sup 18} cm{sup {minus}3} and 6 {times} 10{sup 18} cm{sup {minus}3} respectively for undoped AlSb. Similar levels of O were found in AlAs{sub 0.16}Sb{sub 0.84} films but C levels were an order of magnitude less in undoped and Sn-doped AlAs{sub 0.16}Sb{sub 0.84} films. Hall measurements of AlAs{sub 0.16}Sb{sub 0.84} showed hole concentrations between 1 {times} 10{sup 17} cm{sup {minus}3} to 5 {times} 10{sup 18} cm{sup {minus}3} for Zn-doped material and electron concentrations in the low to mid 10{sup 18} cm{sup {minus}3} for Sn-doped material. They have grown pseudomorphic InAs/InAsSb quantum well active regions on AlAsSb cladding layers. Photoluminescence of these layers has been observed up to 300 K.

More Details
Results 96501–96525 of 100,993
Results 96501–96525 of 100,993
Top