Moessbauer spectroscopy has been used to determine the iron-bearing phases in the coal, catalysts, and IOM products used and generated in the Direct Coal Liquefaction (DCL) catalyst testing program at Sandia National Laboratories, New Mexico. DCL experiments were conducted with a Blind Canyon, Utah, coal both thermally and with three different iron-based catalysts: (1) a sulfated hematite catalyst (Fe{sub 2}O{sub 3}/SO{sub 4}{sup 2{minus}}), (2) a 6-line ferrihydrite catalyst, and (3) iron-oxide impregnated directly into coal. The catalysts were added to the coal at both a 0.5 and a 1.0 wt% level and sufficient sulfur was added to ensure complete sulfidation of the iron. The Moessbauer spectrum of the Blind Canyon coal revealed that the major iron-bearing mineral present was ankerite, Ca(Fe,Mg)(CO{sub 3}){sub 2}, which converts firs to {gamma}-Fe (austenitic iron) before undergoing partial sulfidation to pyrrhotite in the thermal runs. The percentages of pyrrhotite formed in the catalytic runs were higher than those in the thermal runs indicating that sulfidation of the added iron occurs more rapidly than with the ankerite. Moessbauer data on the amount of pyrrhotite present does not correlate well with THF and heptane conversion percentages, indicating that other parameters like catalyst dispersion must also be considered.
In this report the authors describe the methods they have developed for producing stable periodic mesoporous silica gels, thin films of mesoporous silica for sensor applications, a route to nonaqueous synthesis, and the use of various additives in controlling the pore size and structure of these materials. Mesoporous silica is formed by templating silica precursors around micelles of cationic quaternary ammonium surfactants. During the synthesis these micelles undergo a phase transition to a hexagonal, lamellar or cubic liquid crystalline state, thus imposing periodic order on the amorphous silica which occupies the interface of the hydrophilic cationic headgroups of the surfactants. The product of the bulk wet synthesis is a gel composed of micron size silica/surfactant particles, each of which consists of one or more crystalline domains of silica condensed around the surfactant template. The wet gel can then be washed and pyrolyzed to remove the surfactant template, yielding the periodic mesoporous silica product.
In an effort to establish joint activities in the disposition of fissile materials from nuclear materials, the US and Russia agreed to conduct joint work to develop consistent comparisons of various alternatives for the disposition of weapons-grade plutonium. Joint working groups were established for the analysis of alternatives for plutonium management for water reactors, fast reactors, storage, geological formations, immobilization and stabilization of solutions and other forms. In addition cross-cutting working groups were established for economic analysis and nonproliferation (NP). This paper reviews the activities of the NP working group in support of these studies. The NP working group provided integrated support in the area of nuclear NP to the other US/Russian Study teams. It involved both domestic safeguards and security and international safeguards. The analysis of NP involved consideration of the resistance to theft or diversion and resistance to retrieval, extraction or reuse.
Polymer-based routes to ceramic oxides take advantage of precursor chemistry and structure to produce materials with a range of pore sizes. Polymer precursor routes to non-oxide ceramics offer products with superior thermal and chemical stability in many cases. Polymethylsilane (PMS), a versatile cross linked SiC precursor, [(MeHSi){sub x}(MeSi){sub y}], was synthesized using published procedures to yield fluid precursors with a low (20--40%) degree of cross linking. Unique, highly cross linked (60--70%), solid polymers were produced under reaction conditions which carefully conserve the volatile monomer. These two polymers were converted to SiC to determine the relative importance of the various contributions to porosity, and to assess the role of precursor structure on porosity development in non-oxides. Initial results indicate that precursor structure has little effect on porosity. The development of the porosity appears to be dominated by high temperature thermochemistry and/or microstructural changes.
Zeolite films are sought as components of molecular sieve membranes. Different routes used to prepare zeolite composite membranes include growing zeolite layers from gels on porous supports, depositing oriented zeolites on supports, and dispersing zeolites in polymeric membranes. In most cases, it is very difficult to control and avoid the formation of cracks and/or pinholes. The approach to membrane synthesis is based on hydrothermally converting films of layered aluminosilicates into zeolite films. The authors have demonstrated this concept by preparing zeolite A membranes on alumina supports from kaolin films. The authors have optimized the process parameters not only for desired bulk properties, but also for preparing thin (ca. 5 {micro}m), continuous zeolite A films. Scanning electron microscopy shows highly intergrown zeolite A crystals over most of the surface area of the membrane, but gas permeation experiments indicate existence of mesoporous defects and/or intercrystalline gaps. It has been demonstrated that the thickness of the final zeolite A membrane can be controlled by limiting the amount of precursor kaolin present in the membrane.
This project focuses on the modification of silica and alumina surfaces by titania and hydrous titanium oxide ion-exchange films, and the use of these modified materials as supports for MoS{sub 2} catalysts. FTIR studies of molybdena interaction with {gamma}-Al{sub 2}O{sub 3} demonstrate that at low loadings Mo interacts with the most basic hydroxyl groups, and that these hydroxyls are associated with tetrahedrally coordinated Al. Furthermore, hydrodesulfurization (HDS) activity as a function of Mo loading shows a maximum in specific activity with loading. The Mo species bound to tetrahedrally coordinated Al sites are therefore believed to be inactive for the HDS reaction. Only after the tetrahedral Al sites have completely consumed does molybdena adsorb on the alumina in a manner that leads to an active catalyst. According to this scheme, the activity of alumina supported MoS{sub 2} catalysts could be greatly improved by either titrating the tetrahedral Al sites with a modifier, or by using {alpha}-Al{sub 2}O{sub 3} which contains no tetrahedrally coordinated Al. HDS tests over MoS{sub 2} supported on both {alpha}-Al{sub 2}O{sub 3} and {gamma}-Al{sub 2}O{sub 3} modified by a titania film confirm this hypothesis. Neither support material gives rise to a maximum in activity with Mo loading, but rather exhibits a smooth decrease in activity with loading. Furthermore, for equivalent Mo loadings the activity of both of these support materials exceeds that of unmodified {gamma}-Al{sub 2}O{sub 3} due to the fact that no Mo is tied up in the inactive form. FTIR, XPS, and TEM are currently being used to determine whether the model can indeed account for the observed activity trends. Although the surface area of {alpha}-Al{sub 2}O{sub 3} is too low for use as a commercial catalyst, the titania coated {gamma}-Al{sub 2}O{sub 3} represents an important, practical improvement in support materials for hydrotreating catalysts.
The DOE/DOD Environmental Data Bank was established in 1959 as a central location for storing weapons and equipment environments information from a variety of DOE, DOD, and industrial sources and continues to be maintained by Sandia National Laboratories. The Environmental Data Bank contains approximately 2,900 documents regarding normal and abnormal environments that describe the handling, storage, transportation, use, and general phases, which occur during the life of a weapon system. The Environmental Data Bank contains a vast assortment of resources that document crash, fire, and chemical environments resulting from aircraft, rail, ship, and truck accidents, as well as crash and thermal tests conducted on shipping containers. Also included are studies on the hazards of exposure to liquid natural gas fireballs, chemical fireballs, and hydrogen fireballs. This paper describes the DOE/DOD Environmental Data Bank system, its structure, data sources, and usage, with particular emphasis on its use for safety assessments at Sandia National Laboratories.
In this paper the authors identify factors which influence the safety philosophy used in the US commercial/industrial sector and compare them against those factors which influence nuclear weapons safety. Commercial/industrial safety is guided by private and public safety standards. Generally, private safety standards tend to emphasize product reliability issues while public (i.e., government) safety standards tend to emphasize human factors issues. Safety in the nuclear weapons arena is driven by federal requirements and memoranda of understanding (MOUs) between the Departments of Defense and Energy. Safety is achieved through passive design features integrated into the nuclear weapon. Though the common strand between commercial/industrial and nuclear weapons safety is the minimization of risk posed to the general population (i.e., public safety), the authors found that each sector tends to employ a different safety approach to view and resolve high-consequence safety issues.
Over forty safety and security related research and development projects have been initiated between Sandia National Laboratories and the Russian nuclear weapons laboratories VNIIEF and VNIITF. About half of these projects have been completed. All relate to either safety or security methodology development, processes, accident environment analysis and testing, accident databases, assessments or product design of devices. All projects have a potential benefit to various safety or security programs and some may directly have commercial applications. In general, these projects could benefit risk assessments associated with systems that could result in accidents or incidents having high public consequences. These systems typically have already been engineered to have very low assessed probabilities of occurrence of such accidents or incidents. This paper gives an overview of the Sandia surety program with a focus on the potential for future collaboration between Sandia, three Russian Institutes; VNIIEF, VNIITF and VNIIA, and other industry and government organizations. The intent is to serve as an introduction to a roundtable session on Russian Safety Collaboration at the 14th International System Safety Conference. The current Sandia collaboration program scope and rationale is presented along with the evolved program focus. An overview of the projects is given and a few specific projects are briefly highlighted with tangible results to date.
Much work has been devoted to high consequence events with low frequency of occurrence. Characteristic of these events are bridge failure (such as that of the Tacoma Narrows), building failure (such as the collapse of a walkway at a Kansas City hotel), or compromise of a major chemical containment system (such as at Bhopal, India). Such events, although rare, have an extreme personal, societal, and financial impact. An interesting variation is demonstrated by financial losses due to fraud and abuse in the money management system. The impact can be huge, entailing very high aggregate costs, but these are a result of the contribution of many small attacks and not the result of a single (or few) massive events. Public awareness is raised through publicized events such as the junk bond fraud perpetrated by Milikin or gross mismanagement in the failure of the Barings Bank through unsupervised trading activities by Leeson in Singapore. These event,s although seemingly large (financial losses may be on the order of several billion dollars), are but small contributors to the estimated $114 billion loss to all types of financial fraud in 1993. This paper explores the magnitude of financial system losses and identifies new areas for analysis of high consequence events including the potential effect of malevolent intent.
One of the benefits resulting from the collapse of the Soviet Union is the increased dialogue currently taking place between American and Russian nuclear weapons scientists in various technical arenas. One of these arenas currently being investigated involves collaborative studies which illustrate how risk assessment is perceived and utilized in the Former Soviet Union (FSU). The collaborative studies indicate that, while similarities exist with respect to some methodologies, the assumptions and approaches in performing risk assessments were, and still are, somewhat different in the FSU as opposed to that in the US. The purpose of this paper is to highlight the present knowledge of risk assessment methodologies and philosophies within the two largest nuclear weapons laboratories of the Former Soviet Union, Arzamas-16 and Chelyabinsk-70. Furthermore, This paper will address the relative progress of new risk assessment methodologies, such as Fuzzy Logic, within the framework of current risk assessment methods at these two institutes.
Over the past several years, the authors have performed experimental studies focused on understanding small-scale flow processes within discrete fractures and individual matrix blocks; much of the understanding gained in that time differs from that underlying the basic assumptions used in effective media representations. Here they synthesize the process level understanding gained from their laboratory studies to explore how such small-scale processes may influence the behavior of fluid flow in fracture networks and ensembles of matrix blocks at levels sufficient to impact the formulation of intermediate-scale effective media properties. They also explore, by means of a thought experiment, how these same small-scale processes could couple to produce a large-scale system response inconsistent with current conceptual models based on continuum representations of flow through unsaturated, fractured rock. Based on their findings, a number of modifications to existing dual permeability models are suggested that should allow them improved applicability; however, even with these modifications, it is likely that continuum representations of flow through unsaturated fractured rock will have limited validity and must therefore be applied with caution.
The goal of this work is to extend the use of existing path expression theory and methodologies to ensure that critical software event sequences are maintained even in the face of malevolent attacks and harsh or unstable operating environments. This will be accomplished by providing dynamic fault management measures directly to the software developer and to their varied development environments. This paper discusses the perceived problems, a brief overview of path expressions, and the author`s proposed extension areas. The authors discuss how the traditional path expression usage and implementation differs from the intended usage and implementation.
Garnet phosphors have potential for use in field emission displays (FEDs). Green-emitting Gd{sub 3}Ga{sub 5}O{sub 12}:Tb (GGG:Tb) and Y{sub 3}Al{sub 5}O{sub 12}:Tb (YAG:Tb) are possible alternatives to ZnO:Zn, because of their excellent resistance to burn, low-voltage efficiency, (3.5 lm/W from GGG:Tb at 800 V), and saturation resistance at high power densities. Hydrothermal and combustion synthesis techniques were employed to improve the low-voltage efficiency of YAG:Tb, and Y{sub 3}Ga{sub 5}O{sub 12}:Tb (YGG:Tb). Synthetic technique did not affect low-voltage (100--1,000 V) efficiency, but affected the particle size, morphology, and burn resistance. The small particle size phosphors obtained via hydrothermal (<1 {micro}m) and combustion reactions (<1 {micro}m) would benefit projection TV, high-definition TV (HDTV), and heads-up displays (HUDs), where smaller pixel sizes are required for high resolution.
Inductively Coupled Plasma (ICP) sources are extremely promising for large-area, high-ion density etching or deposition processes. In this review the authors compare results for GaAs and GaN etching with both ICP and Electron Cyclotron Resonance (ECR) sources on the same single-wafer platform. The ICP is shown to be capable of very high rates with excellent anisotropy for fabrication of GaAs vias or deep mesas in GaAs or GaN waveguide structures.
Vulnerability analyses for information systems are complicated because the systems are often geographically distributed. Sandia National Laboratories has assembled an interdisciplinary team to explore the applicability of probabilistic logic modeling (PLM) techniques (including vulnerability and vital area analysis) to examine the risks associated with networked information systems. The authors have found that the reliability and failure modes of many network technologies can be effectively assessed using fault trees and other PLM methods. The results of these models are compatible with an expanded set of vital area analysis techniques that can model both physical locations and virtual (logical) locations to identify both categories of vital areas simultaneously. These results can also be used with optimization techniques to direct the analyst toward the most cost-effective security solution.
The in-scattering processes, which reduce the decay of the active medium polarization, should be included in a consistent treatment of semiconductor laser gain. The in-scattering processes affect the laser gain by decreasing the influence of the high k-states, which contribute absorption to the spectrum. A theory, based on the semiconductor-Bloch equations with the effects of carrier-carrier scattering treated at the level of the quantum kinetic equations in the Markov limit, predicts gain spectra that do not exhibit absorption below the renormalized band gap, in agreement with experiment. When compared to gain calculations where the in-scattering contribution is neglected, the theory predicts markedly different properties for intrinsic laser parameters, such as peak gain, gain bandwidth, differential gain and carrier density at transparency, especially at low carrier densities.
Critical software must be safe, secure, and dependable. Traditionally, these have been pursued as separate disciplines. This presentation looks at the traditional approaches and highlights commonalities and differences among them. Each can learn from the history of the others. More importantly, it is imperative to seek a systems approach which blends all three.
Test data on canonical weapon-like fixtures are used to validate previously developed analytical bounding results. The test fixtures were constructed to simulate (but be slightly worse than) weapon ports of entry but have known geometries (and electrical points of contact). The exterior of the test fixtures exhibited exterior resonant enhancement of the incident fields at the ports of entry with magnitudes equal to those of weapon geometries. The interior consisted of loaded transmission lines adjusted to maximize received energy or voltage but incorporating practical weapon geometrical constraints. New analytical results are also presented for bounding the energies associated with multiple bolt joints and for bounding the exterior resonant enhancement of the exciting fields.
Prosperity Games{trademark} are an outgrowth and adaptation of move/countermove and seminar War Games. Prosperity Games{trademark} are simulations that explore complex issues in a variety of areas including economics, politics, sociology, environment, education and research. These issues can be examined from a variety of perspectives ranging from a global, macroeconomic and geopolitical viewpoint down to the details of customer/supplier/market interactions in specific industries. All Prosperity Games{trademark} are unique in that both the game format and the player contributions vary from game to game. This report documents the Biomedical Technology Prosperity Game{trademark} conducted under the sponsorship of Sandia National Laboratories, the Defense Advanced Research Projects Agency, and the Koop Foundation, Inc. Players were drawn from all stakeholders involved in biomedical technologies including patients, hospitals, doctors, insurance companies, legislators, suppliers/manufacturers, regulators, funding organizations, universities/laboratories, and the legal profession. The primary objectives of this game were to: (1) Identify advanced/critical technology issues that affect the cost and quality of health care. (2) Explore the development, patenting, manufacturing and licensing of needed technologies that would decrease costs while maintaining or improving quality. (3) Identify policy and regulatory changes that would reduce costs and improve quality and timeliness of health care delivery. (4) Identify and apply existing resources and facilities to develop and implement improved technologies and policies. (5) Begin to develop Biomedical Technology Roadmaps for industry and government cooperation. The deliberations and recommendations of these players provided valuable insights as to the views of this diverse group of decision makers concerning biomedical issues. Significant progress was made in the roadmapping of key areas in the biomedical technology field.
The behavior of chemical species adsorbed on solid surfaces and exchanged into clay interlayers plays a significant role in controlling many natural and technologically important processes, including rheological behavior, catalysis, plant growth, transport in natural pore fluids and those near anthropogenic hazardous waste sites, and water-mineral interaction. Adsorption and exchange reactions have been the focus of intense study for many decades. Only more recently, however, have there been extensive spectroscopic studies of surface species. Among the spectroscopic methods useful for studying surface and exchanged species (e.g., infrared, X-ray photoelectron spectroscopy [XPS] and X-ray absorption spectroscopy [XAS]), nuclear magnetic resonance spectroscopy (NMR) has the considerable advantage of providing not only structural information via the chemical shift and quadrupole coupling constant but dynamical information in the Hz-mHz range via lineshape analysis and relaxation rate measurements. It is also possible to obtain data in the presence of a separate fluid phase, which is essential for many applications. This paper illustrates the range of applications of NMR methods to surface and exchanged species through review of recent work from our laboratory on Cs in clay interlayers and Cs, Na and phosphate adsorbed on oxide surfaces. The substrate materials used for these experiments and our long-term objectives are related to problems of geochemical interest, but the principals and techniques are of fundamental interest and applicable to a wide range of technological problems.
The software construction process consists of a mixture of informal and formal steps. By their very nature, informal steps cannot be formally verified. Empirical evidence suggests that a majority of software errors originate in the informal steps of the software development process. For this reason, when constructing high assurance software, it is essential that a significant effort be made to increase one`s confidence (i.e., to validate) that the informal steps have been made correctly. Visualization and animation can be used to provide an `intuitive proof` that the informal steps in the software construction process are correct. In addition, the formal portion of software construction often permits/demands artistic (informal) decisions to be made (e.g., design decisions). Such decisions often have unexpected/unforeseen consequences that are only discovered later in the development process. Visualization and animation techniques can be brought to bear on this aspect of the software construction process by providing a better intuitive understanding of the impact of the informal decisions that are made in program development. This increases the likelihood that undesirable decisions can be avoided or at least detected earlier in the development process.
US DOE national laboratories and Russian institutes are becoming increasingly cooperative in support of nonproliferation of nuclear materials. This paper describes completed projects, current work, and areas of possible future cooperation between US laboratories and a Russian Ministry of Atomic Energy (MINATOM) entity, Special Scientific and Production State Enterprise (SNPO). The Kurchatov Institute, SNPO, and the US national laboratories jointly completed a physical protection system (PPS) for a facility housing two reactors at Kurchatov Institute within a very short time frame in 1994. Spin- off projects from this work resulted in a US-witnessed acceptance test of the new system adhering to a procedure adopted in Russia, and visits by DOE laboratories` personnel to SNPO`s sensor development and test facilities at Dubna and Penza. SNPO was one of the MINATOM sites at which Lawrence Livermore National Laboratory and Sandia National Laboratories (SNL) conducted a vulnerability assessment training course. Current cooperative projects include additional physical protection upgrades at Kurchatov where SNPO is involved as an installer and supplier of sensors, alarm display, video, and fiber optic equipment. Two additional contracts between SNL and SNPO result in information on Russian sensor performance and cost and an exchange of US and Russian sensors. Russian sensors will be tested in the United States,a nd US sensors will be tested in Russia. Pacific Northwest Laboratory administers a contract to document the process of certifying physical protection equipment for use at MINATOM facilities. Recent interest in transportation security has opened a new area of cooperation between the national laboratories and SNPO. Future projects are expected to include SNPO participation in physical protection upgrades at other locations in Russia, pedestrian and vehicle portal development, positive personnel identifier testing, and the exchange and testing of additional equipment.
Soil vapor surveys were performed to characterize the approximate location of soil contaminants at a hazardous waste site. The samplers were from two separate companies and a comparison was made between the results of the two techniques. These results will be used to design further investigations at the site.
Material which is not in direct contact with detonating explosives may still be driven by the explosion through impact by driven material or by attachment to driven material. In such circumstances the assumption of inelastic collision permits estimation of the final velocity of an assemblage. Examples of the utility of this assumption are demonstrated through use of Gurney equations. The inelastic collision calculation may also be used for metal parts which are driven by explosives partially covering the metal. We offer a new discounting angle to account for side energy losses from laterally unconfined explosive charges in cases where the detonation wave travels parallel to the surface which is driven.