Sensitivity studies have been conducted for the gas release from the Waste Isolation Pilot Plant (WIPP) using the TOUGH2 computer code with performance measures of peak repository pressure and gas migration distance at 1000 years. The effect of formation permeabilities including impermeable halite, two-phase characteristic curves including different models and residual saturations, and other variations was studied to determine their impact on the performance of the WIPP repository. 15 refs., 7 figs., 2 tabs.
The standard operating mode produces bremsstrahlung with an endpoint energy of about 18 MeV. This paper describes a new mode with a 8.5 MeV endpoint energy and the same standard mode pulse characteristics achieved by operating only half of the accelerator at full charge with the advantage of minimal setup time. An extension of the new half-voltage mode is to use the other half of the accelerator for delivering a second pulse at a later time with the same technique. The double pulse mode is ideal for beam generation which requires a long interpulse time in the millisecond regime. The beam characteristics of the two half-voltage pulses are nearly identical with the nominal radiation pulse full width at half maximum of 21 ns and 10--90 risetime of 11 ns recorded by the same Compton diode radiation monitors on instruments triggered 30 ms apart.
A series of shock-loading experiments on a nitrocellulose-based (NC-based) gun propellant was conducted using a light-gas gun. The intent of this work was to characterize the shock sensitivity of the gun propellant. The initial objectives were to obtained Hugoniot data and to investigate the pressure threshold at which a reaction initiates. For the Hugoniot/reaction threshold experiments, 1/4-length grains of propellant were mounted on the front of projectiles and were impacted onto either polymethylmethacrylate (PMMA), fused silica or sapphire targets at velocities as high as 1.4 mm/{mu}s, the upper limit of the gun. The particle velocity data obtained from the VISAR (Velocity Interferometer System for Any Reflector) records for the propellant fit a Hugoniot curve found in the Russian literature for a double-base, NC-nitroglycerine propellant. The density initial bulk sound velocity, and empirical parameter S values for the gun propellant were 1.63 g/cm{sup 3}, 1.70 mm/{mu}s and 1.85, respectively. VISAR data were also used to obtained the ignition threshold pressures of the gun propellant. Reactions were observed at impact pressures of 2.6 GPa and above. 5 refs., 6 figs., 1 tab.
We report on the use of a deposition/etch approach to the loss of selectivity problem, using high activity fluorine chemistries in the etch step. Proof-of-concept experiments were initially performed in a hot wall system, the excellent results obtained lead us to prove out the concept in a commercially available cold wall Genus reactor. We observed that WF{sub 6} is ineffective as an etchant of W. The technique has been able to produce perfectly selective depositions 1 micron thick in both hot wall, and cold wall, systems. Sheet resistivity values and film morphology are good. 9 refs., 4 figs., 1 tab.
This paper's main result is an O(({radical}{bar m}lgm)(n lg n) + mlg n)-time algorithm for computing the kth smallest entry in each row of an m {times} n totally monotone array. (A two-dimensional A = a(i,j) is totally monotone if for all i{sub 1} < i{sub 2} and j{sub 1} < j{sup 2}, < a(i{sub 1},j{sub 2}) implies a(i{sub 2},j{sub 1})). For large values of k (in particular, for k=(n/2)), this algorithm is significantly faster than the O(k(m+n))-time algorithm for the same problem due to Kravets and Park. An immediate consequence of this result is an O(n{sup 3/2} lg{sup 2}n)-time algorithm for computing the kth nearest neighbor of each vertex of a convex n-gon. In addition to the main result, we also give an O(n lg m)-time algorithm for computing an approximate median in each row of an m {times} n totally monotone array; this approximate median is an entry whose rank in its row lies between (n/4) and (3n/4) {minus} 1. 20 refs., 3 figs.
This paper presents a practical algorithm for partitioning a program into sequential threads. A thread is a sequence of instructions, possibly including branches, which can be scheduled as an indivisible unit on a von Neumann-like processor. The partitioning algorithm is designed for a non-strict (but not lazy) language with non-strict data structures and side-effects. The primary target of the proposed compilation strategy is large-scale parallel systems which rely on multithreading at the processor level to tolerate long communication latencies. As such, the algorithm incorporates a mechanism to balance the desire to maximize thread length with the desire to expose useful high-level parallelism. Although this paper focuses on non-strict semantics in conjunction with a parallel multithreaded architecture, the partitioning analysis is equally well suited (with appropriate simplifications) to a non-strict language on a sequential machine or a strict language on a parallel multithreaded machine. Our analysis is accomplished without compromising non-strict semantics and without creating dependencies which sacrifice useful high-level parallelism. It can also exploit known dependency information. The analysis starts with a traditional dataflow graph and partitions it into a set of interrelated threads. 16 refs., 9 figs.
The Silver Bullet Skunk Works, and experimental product realization team at AT T Consumer Products, designed and shipped a new telephone answering system to market in eight months, approximately one year faster than previous AT T products of similar complexity. This paper outlines the Design for X'' (DFX) philosophies and the team structure that enabled the group to accelerate the Product Realization Process. The Answering System 1300, developed in record time, was a successful product that met its schedule and cost objectives, and sold out its entire high-volume manufacturing run. Lessons learned from the Skunk Works experience have since been applied to other development activities in AT T Consumer Products. 3 figs.
Increasingly stringent air emission standards in various states has dictated the elimination of engineering finishes which are derived from high volatile organic compound (VOC) paint chemistries. In July 1989, Allied-Signal, Inc., Kansas City Division, Kansas City, Missouri, voluntarily closed its paint facility, due to non-compliance with local air emission standards. The following details the materials selection and evaluations which led to current processing using low VOC paints, which permitted the Allied Signal, Inc., paint facility to achieve compliance and resume operations. 1 tab.
We have developed a model which utilizes a probabilistic failure criterion to describe intergranular stress corrosion cracking (IGSCC). A two-dimensional array of elements representing a section of a pipe wall is analyzed, with each element in the array representing a segment of grain boundary. The failure criterion is applied repetitively to each element of the array that is exposed to the interior of the pipe (i.e. the corrosive fluid) until that element dissolves, thereby exposing the next element. A number of environmental, mechanical, and materials factors have been incorporated into the model, including: (1) the macroscopic applied stress profile, (2) the stress history, (3) the extent and grain-to- grain distribution of carbide sensitization levels, which can be applied to a subset of elements comprising a grain boundary, and (4) a data set containing IGSCC crack growth rates as function of applied stress intensity and sensitization level averaged over a large population of grains. The latter information was obtained from the literature for AISI 304 stainless steel under light water nuclear reactor primary coolant environmental conditions. The resulting crack growth simulations are presented and discussed. 14 refs., 10 figs.
Edge finishing and deburring of parts is a tedious operation that should be automated. This paper describes the use of direct-drive XY table in the automated edge finishing of machined parts. The table is faster and more accurate than an articulated robot, thus where planar motion in a small work area is sufficient it is preferable. Hybrid force/position control is used to guide the table (with mounted workpiece) past the tool and maintain the contact force at the desired level. A six-axis force sensor on the tool spindle is used to measure contact force. We identified a dynamic model for the table from experimental measurements and used this model to design a force/position controller for the table. An example application of the table in the deburring of an actual jet engine turbine hub is presented. 5 refs., 12 figs.
This paper justifies the need for and describes studies of brine chemistry under way for German and American high- and intermediate-level radioactive waste repositories in domal and bedded salt formation. In particular, it discusses the origin and composition of fluids that could enter these repositories and some sampling, modeling, and statistical techniques used to characterize them. 24 refs., 4 figs., 5 tabs.
Historically, characterization of fluid flow and transport of soluble elements in the unsaturated, or vadose, zone has been limited. Until recently, most of the interest in transport of water-soluble pollutants has been focused on aquifer contamination, i.e. saturated conditions. Vadose zone investigations are hampered by a lack of appropriate technology for the necessary measurements; little work has been done to relate laboratory measurements to field-scale effects; and development and validation of computational models has been limited, in part through lack of data. We describe here results of a small-scale field experiment in which existing technology is used to quantify fluid movement following controlled infiltration. 6 refs., 2 figs.
Sandia National Laboratories has considerable experience with video systems used for alarm assessment. Until recently the camera of choice for lighted security applications was the monochrome vacuum tube video camera. However, with recent advancements in the solid state imager technology, the integration of tube cameras in security systems may soon become obsolete. The sensitivity and resolution of solid state imagers is approaching that of vacuum tube imagers. In addition, solid state cameras have a relatively long lifetime and require little maintenance. Initial equipment costs are similar. Due to the increased performance of solid state imagers, Sandia has established an ongoing program to evaluate these cameras. The evaluations are performed mainly to verify manufacturers' specifications for resolution, sensitivity, and signal to noise ratio, which are the critical camera parameters that should be considered when designing video systems. This report defines these parameters, describes the test procedures, and provides test results. 1 figs., 2 tabs.
Zeolite-based tritium lamps are a possible alternative to traditional tritium gas tube light sources. Rare earth luminescing centers may be ion-exchanged into zeolite matrices. Close proximity of tritium atoms to the rare earths can be provided by highly tritiated water sorbed within the pore structure of the zeolite aluminosilicate matrix. Zeolites are optically clear and radiation stable. Light outputs from tritium-loaded zeolites are shown here to exceed 2{mu}W/cm{sup 2}, with good stability. Procedures for obtaining light sources are presented and results are discussed. The possible use of these luminescent materials as process monitors for zeolite absorption columns in tritium service is also discussed. 13 refs., 3 figs.
To provide a method for addressing the uncertainty associated with conceptual models developed for performance assessment of waste management sites, probabilistic networks have been applied to the conceptual model development process. The application of probabilistic networks provides a graphical representation of the reasoning process that goes into developing conceptual models. Probability tables associated with decision points in the process provide a quantification of the uncertainty that is associated with the resulting conceptual models. To support the development of this probabilistic network, a formal process is being designed and implemented to elicit expert information about the conceptual model development process. This paper discusses the approach to designing this expert judgment elicitation process. 10 refs.
The short-transverse (S-T) stress corrosion cracking (SCC) behavior of Al-Li-CU alloy 2090 was studied using a static load SCC test technique. Time to failure was measured as a function of applied potential in several different environments. Rapid SCC failures (< 10 hours) were observed only when the following criteria were satisfied: E{sub br, T1} < E{sub applied} < E{sub br, matrix} where potentials refer to the breakaway potentials of the subgrain boundary T{sub 1} (Al{sub 2}CuLi) phase and the {alpha}-Al matrix phase. E{sub br} values were measured using potentiodynamic polarization of bulk materials intended to simulate the individual phases found in the subgrain boundary region. Results strongly suggest an anodic dissolution based SCC mechanism for this alloy where selective dissolution of T{sub 1} on the subgrain boundary is a critical step. The unusual pre-exposure embrittlement phenomenon demonstrated by Al- Li alloys is also shown to be consistent with these simple SCC criteria. 21 refs., 9 figs., 6 tabs.
One of the possible consequences of disruptions is the generation of runaway electrons which can impact plasma facing components and cause damage due to high local energy deposition. This problem becomes more serious as the machine size and plasma current increases. Since large size and high currents are characteristics of proposed future machines, control of runaway generation is an important design consideration. A lumped circuit model for disruption runaway electron generation indicates that control circuitry on strongly influence runaway behavior. A comparison of disruption data from several shots on JET and D3-D with model results, demonstrate the effects of plasma motion on runaway number density and energy. 6 refs., 12 figs.
Benchmarking a network file server introduces some unique considerations over traditional benchmarking scenarios. Since the user is executing on a client system interconnected to the file server, the client and network must be provided for during benchmarking. During a recent procurement action, Sandia National Laboratories was challenged to develop a benchmark suite that would accurately test the network requirements. This paper describes the benchmark design and summarizes the experience gained from the benchmark executions. 8 refs., 2 figs.
The electromagnetic field in a mode-stirred chamber is a random process. Samples of this random process are random variables. Different realizations of this random variable can be obtained by changing the paddle-wheel angle, changing the frequency, or changing the location at which the sample is taken. Correlation widths can be defined for each of these three variables. For examples, the spatial correlation width is the distance a point sensor must be moved to realize an uncorrelated value of the field (paddle-wheel angle and frequency held constant). Likewise, the paddle-wheel correlation width is the angle through which the paddle wheel must turn to yield an uncorrelated value (location and frequency held constant). The frequency correlation width is the frequency change required to yield an uncorrelated value (location and paddle-wheel angle held constant). These values were determined experimentally for the sandia mode-stirred chamber by sampling the field at equal increments (for each variable) and calculating an autocorrelation function. The autocorrelation function is a random process (because it is calculated from a random process) and must be averaged to determine it width. The correlation widths were found to be less than 0.1{degree} for paddle-wheel angle, 50 kHz for frequency, and half a wavelength for spatial location. 4 refs., 3 figs., 2 tabs.
Although the feasibility of using PZT and PLZT films for optical data processing applications, such as optical storage disks, image comparators, and spatial light modulators, has clearly been established, most of the critical parameters related to the storage and readout processes still need to be evaluated. Optical readout techniques capable of nondestructively determining the value of polarization are based either on the quadratic electrooptic effect or on a photocurrent response. In reflection, large electrooptic retardations (>60{degrees}) have now been achieved with thin PZT films ({approx equal} 0.5 {mu}m) under conditions that optimize interference effects. These results are quite attractive for device applications. Model calculations, based on the equations of reflection ellipsometry, have been used to develop a framework for understanding those results. The magnitude of the photocurrent response has also been used to determine the polarization state. However, the photocurrent always has the same sign, regardless of the sign of the polarization, which suggests the presence of a strong bias field due to at least one of the interfaces. In addition, the accumulation of space charge after a succession of measurements suppresses the photocurrent transient, which severely limits the utility of a photocurrent based readout. 7 refs., 9 figs.
The contact of aluminum-based melts with liquid water has been shown to be explosive in many experiments performed by the aluminum industry and in several nuclear reactor experiments and accidents. In order to obtain quantitative information relating to the fuel-coolant interactions that might occur with aluminum-based fuel, a laboratory-scale experimental study is being performed at Sandia National Laboratories. The overall objective of this research program is to provide an understanding of the mechanism of steam explosions with the melt compositions expected in several hypothetical core meltdown accident scenarios in production reactors. In this program it has been demonstrated that rapid exothermic metal-water reactions can accompany the steam explosions under certain conditions resulting in enhanced energy release and in the concomitant generation of hydrogen. 4 refs., 2 figs.
The INTEROP Achievement Award will be given to those customer organizations that make the most effective use of internetworking technology to further their own specific business aims. This paper is an application for this award by Sandia National Laboratories. Given are the network application, topology, and the types of systems to which it is applied.(JEF)
One problem with electromagnetic time domain finite-difference simulations in cylindrical coordinates is the rapidly decreasing characteristic dimension of the cells as r approaches zero. In order to satisfy the Courant stability condition a small time step is needed to insure stability, which is undesirable because it increases the cost of the simulation. In our presentation, we will describe a method which uses a rectangular grid and an annular cylindrical grid which overlap to perform electromagnetic simulations of cylindrical geometries. The two grids are connected by interpolating the field at the grid points of one grid using field values from the second grid. 2 refs.
The strength of deuterium bonding to the walls of closed cavities within Si was determined in ion-beam experiments. These studies circumvented an inherent indeterminacy in the analysis of external-surface desorption and thereby allowed the Si-H surface bond energy to be quantified for the first time. The bond energy is 2.5 {plus minus} 0.2 eV for submonolayer coverages. 14 refs., 3 figs.
