Publications

Results 100301–100325 of 100,993

Search results

Jump to search filters

The preparation of InAsSb/InSb SLS (strained-layer superlattice) and InSb photodiodes by MOCVD

Biefeld, Robert M.

Infrared absorption and photoluminescence have been demonstrated for InAs{sub 1-x}Sb{sub x}/InSb strained-layer superlattices (SLS's) in the 8--15 {eta}m region for As content less than 20%. This extended infrared activity is due to the type II heterojunction band offset in these SLS's. The preparation of the first MOCVD grown p-n junction diode was achieved by using dimethyltellurium as an in-type dopant. Several factors, such as background doping and dopant profiles affect the performance of this device. InSb diodes have been prepared using tetraethyltin. The resulting current-voltage characteristics are improved over those of diodes grown previously using dimethyltellurium. Doping levels of 8 {times} 10{sup 15} to 5 {times} 10{sup 18} cm{sup {minus}3} and mobilities of 6.7 {times} 10{sup 4} to 1.1 {times} 10{sup 4} cm{sup 2}/Vs have been measured for Sn doped InSb. SLS diode structures have been prepared using Sn and Cd as the dopants. Structures prepared with p-type buffer layers are more reproducible. 5 refs., 4 figs.

More Details

MELCOR analysis of the TMI-2 accident

Boucheron, Edward A.

This paper describes the analysis of the Three Mile Island-2 (TMI-2) standard problem that was performed with MELCOR. The MELCOR computer code is being developed by Sandia National Laboratories for the Nuclear Regulatory Commission for the purpose of analyzing severe accident in nuclear power plants. The primary role of MELCOR is to provide realistic predictions of severe accident phenomena and the radiological source team. The analysis of the TMI-2 standard problem allowed for comparison of the model predictions in MELCOR to plant data and to the results of more mechanistic analyses. This exercise was, therefore valuable for verifying and assessing the models in the code. The major trends in the TMI-2 accident are reasonably well predicted with MELCOR, even with its simplified modeling. Comparison of the calculated and measured results is presented and, based on this comparison, conclusions can be drawn concerning the applicability of MELCOR to severe accident analysis. 5 refs., 10 figs., 3 tabs.

More Details

Kinetics of molecular beam epitaxy: Effect of ion-induced sputtering

Richards, P.M.

Steady state roughness of surfaces growing by molecular beam epitaxy is investigated by Monte Carlo simulations under conditions where an ion beam is also present which sputters adatoms off the surface. If the sputtering is random, it only increases the roughness. But if the sputtering probability is strongly dependent on the binding energy of an adatom within a cluster or island, the ions can have a smoothening effect. Physical arguments are given in support of the results. 8 refs., 4 figs.

More Details

Photovoltaic concentrator module reliability: Failure modes and qualification

Richards, Elizabeth H.

The purpose of this paper is to discuss the current issues of interest in PV concentrator module reliability. Before describing in detail the reliability concerns about PV concentrator modules, it should be emphasized that, with proper design and attention to quality control, there is nothing to prevent concentrator modules from being as reliable as crystalline-silicon flat-plate modules have proven to be. Concentrator modules tested outdoors, as well as in the first-generation systems, have generally been reliable, and no degradation in cell output has been observed. Also, although they are not included in this paper, there are a few items currently of concern with the reliability of other PV module technologies that are not issues with PV concentrator technology, such as the stability of amorphous-silicon efficiencies and concerns about EVA encapsulation.

More Details

Flow behavior of Ti-24Al-11Nb at high strain rates

Bourcier, R.J.

The deformation and crack initiation behavior of Ti-24Al-11Nb has been examined over a temperature range of 298 to 923 K and for strain rates from 10{sup {minus}4}/s to 10{sup 2}/s. Tests performed in compression indicate much lower strain hardening at 10{sup 2}/s than at either 10{sup {minus}1}/s or 10{sup {minus}4}/s at all temperatures. Associated with this behavior is the occurrence of non-uniform, localized deformation bands at 10{sup 2}/s. An analysis indicates that adiabatic deformation conditions predominate at 10{sup 2}/s and that these result in adiabatic softening. Furthermore, as a result of non-uniform deformation and adiabatic heating, this Ti{sub 3}-Al-based alloy is actually more resistant to strain-induced microcrack initiation at 10{sup 2}/s than at 10{sup {minus}4}/s during room temperature testing. 16 refs., 7 figs.

More Details

On the construction of constitutive equations for large deformations

Herrmann, W.

This paper attempts to give an elementary review of the kinematics of large deformations with a view to illustrating some of the underlying geometric concepts, and then goes on to review some basic features of elastic, hypoelastic, and rate type constitutive equations relevant to their use in numerical methods. Since some recent work has emphasized working in a rotated'' intermediate configuration, one in which the rigid body rotation has been backed out, results relating to this configuration are included, otherwise all of the results have been read off directly from Truesdell and Toupin ( ) or Truesdell and Noll ( ). Finally, results given by Nemat-Nasser ( ) are quoted which reconcile some generalizations of infinitesimal plasticity and some remarks are made relevant to the introduction of tensor internal state variables. Thermodynamic effects, although important in calculations, are omitted to emphasize kinematical effects. Because recent authors have used different names and symbols for stress and strain tensors, it has been found necessary to give a self contained if abbreviated development of the kinematics, which, however, allows a compact discussion of constitutive equations.

More Details

Formation of catalysts in inverse micelles

Wilcoxon, Jess P.

We report formation of several small colloidal metal catatlysts in inverted micelle (oil-continuous) systems. These materials have demonstrated catalytic activity in situ (i.e. unsupported). The range of solvents possible in this process is large, including all saturated hydrocarbons, cyclic hydrocarbons (e.g. cyclohexane) and aromatics (e.g. toluene, xylene). Three classes of micelle system were investigated, nonionic, anionic, and cationic. Nonionic types allow precise size control but in general do not act as strong stabilizing agents at high temperatures. Cationics can be chosen to provide this permanent stability, providing both charge and steric stabilization. Metal systems formed include Rh, Ni, NiB, MoO{sub 2}, Pd, Au and Ag and alloys. Selected examples are given. 4 figs.

More Details

Core structure heat-up and material relocation in a BWR short-term station blackout accident

Schmidt, Rodney C.

This paper presents an analytical and numerical analysis which evaluates the core-structure heat-up and subsequent relocation of molten core materials during a NWR short-term station blackout accident with ADS. A simplified one-dimensional approach coupled with bounding arguments is first presented to establish an estimate of the temperature differences within a BWR assembly at the point when structural material first begins to melt. This analysis leads to the conclusions that the control blade will be the first structure to melt and that at this point in time, overall temperature differences across the canister-blade region will not be more than 200 K. Next, a three-dimensional heat-transfer model of the canister-blade region within the core is presented that uses a diffusion approximation for the radiation heat transfer. This is compared to the one-dimensional analysis to establish its compatibility. Finally, the extension of the three-dimensional model to include melt relocation using a porous media type approximation is described. The results of this analysis suggest that under these conditions significant amounts of material will relocate to the core plate region and refreeze, potentially forming a significant blockage. The results also indicate that a large amount of lateral spreading of the melted blade and canister material into the fuel rod regions will occur during the melt progression process. 22 refs., 18 figs., 1 tab.

More Details

Fatigue reliability of wind turbine components

Veers, Paul S.

Fatigue life estimates for wind turbine components can be extremely variable due to both inherently random and uncertain parameters. A structural reliability analysis is used to qualify the probability that the fatigue life will fall short of a selected target. Reliability analysis also produces measures of the relative importance of the various sources of uncertainty and the sensitivity of the reliability to each input parameter. The process of obtaining reliability estimates is briefly outlined. An example fatigue reliability calculation for a blade joint is formulated; reliability estimates, importance factors, and sensitivities are produced. Guidance in selecting distribution functions for the random variables used to model the random and uncertain parameters is also provided. 5 refs., 9 figs., 1 tab.

More Details

Status of concentrator collector and high-efficiency concentrator cell development

Gee, James M.

Photovoltaic concentrator collectors are an attractive option for utility-scale photovoltaic power plants. This paper reviews the current status of photovoltaic concentrator collector and cell development. Included in the review is a discussion of the economic motivation for concentrators, a summary of recent concentrator collector and cell development, and a description of a major new program to accelerate development and commercial introduction of concentrator collectors. 21 refs., 1 fig., 3 tabs.

More Details

Video motion detection for physical security applications

Matter, John C.

Physical security specialists have been attracted to the concept of video motion detection for several years. Claimed potential advantages included additional benefit from existing video surveillance systems, automatic detection, improved performance compared to human observers, and cost effectiveness. In recent years significant advances in image processing dedicated hardware and image analysis algorithms and software have accelerated the successful application of video motion detection systems to a variety of physical security applications. Currently Sandia is developing several advanced systems that employ image processing techniques for a broader set of safeguards and security applications. TCATS (Target Cueing and Tracking System) uses a set of powerful, flexible, modular algorithms and software to alarm on purposeful target motion. Custom TCATS hardware optimized for perimeter security applications is currently being evaluated with video input. VISDTA (Video Imaging System for Detection, Tracking, and Assessment) uses some of the same TCATS algorithms and operates with a thermal imager input. In the scan mode, VISDTA detects changes in a scene from the previous image at a given scan point; in the stare mode, VISDTA detects purposeful motion similar to TCATS.

More Details

Adhesion at ceramic interfaces

Michalske, Terry A.

Many of the properties associated with ceramic materials such as high hardness, high dielectric constant, refractoriness, and good optical properties will play a critical role in the development of devices for new and emerging technologies. In many cases, the combination of properties that is required demands that a composite material be designed to fulfill these complex materials needs. The increasing emphasis upon composite materials design and performance necessarily focuses greater attention upon the structure and properties of interfaces in ceramic materials. One on the most important aspects of interfacial behavior is the adhesive stability. As an example, high hardness ceramic coatings for tribological applications require a high degree of interfacial adhesion with the underlying substate material. Alternatively it has been shown that fiber reinforced ceramic composites that are designed for high fracture toughness must contain weak interfaces that allow for fiber pull-out to toughen the instrinsically brittle ceramic matrix. Our ability to design ceramic interfaces for specific interfacial adhesive behavior dictates that we develop a full understanding of the factors that control the adhesive bond in these systems. We report on the use of continuum fracture mechanics techniques to identify the molecular source of adhesion between oxide surfaces and introduce a new approach to measuring interfacial adhesive forces using an Interfacial Force Microscope.

More Details

Joint computational/experimental aerodynamics research on a reentry vehicle

Oberkampf, W.L.; Aeschliman, D.P.

Although computational aerodynamics simulation has been taking more responsibility during recent years, wind tunnel experimentation has continued to play the major role in flight vehicle analysis and design.This role, however, is changing because of the great strides in the capability and confidence in numerical simulations. For a small, well defined, class of supersonic and hypersonic flow problems, high quality numerical solutions are now believed to represent the physics of the problem more accurately than a wind tunnel experimental can simulate the free flight conditions. An example of this is the supersonic or hypersonic, laminar, perfect gas flow over a spherically blunted cone at low angle of attack. In this paper, aerodynamic force and moment measurements and flow visualization results are presented for a reentry vehicle configuration at Mach 8. All of the results were obtained in the Sandia Mach 8 long duration, blow-down, hypersonic wind tunnel. The basic vehicle configuration is a spherically blunted cone with a slice parallel with the axis of the vehicle. Onto the slice portion of the vehicle can be attached flaps with three different deflection angles, 10, 20 and 30 deg. Flow visualization results include surface oil flow, spark Schlieren, and liquid crystal photographs. 1 ref., 7 figs.

More Details

A theoretical investigation of effective surface recombination velocity in AlGaAs/GaAs heteroface solar cells

Gee, James M.

An AlGaAs window layer is used in high-efficiency GaAs solar cells to reduce carrier recombination at the front surface. Free surfaces of III-V semiconductors have a high density of surface states that serve as recombination sites and create a depletion region at the front surface. We have performed a theoretical investigation of front-surface recombination that includes the effect of a surface space-charge layer. It was found that the surface space-charge layer can have a profound effect on front-surface recombination for thin or lightly doped window layers. 15 refs., 5 figs., 1 tab.

More Details

Natural-analog studies for partial validation of conceptual models of radionuclide retardation at the Waste Isolation Pilot Plant (WIPP)

Siegel, Malcolm

Transport by groundwater within the Culebra Dolomite, an aquifer above the Waste Isolation Pilot Plant (WIPP), is the most probable mechanism for long-term release of radionuclides to the accessible environment. Radionuclides could be retarded by sorption if the groundwater is exposed to sufficient amounts of fracture-lining clays. In this natural-analog study, distributions of U and trace metals have been examined to constrain the strength of clay/solute interactions within the Culebra. Uranium solid/liquid distribution ratios, calculated from U concentrations of groundwaters and consanguineous fracture-filling clays, range from {approximately}80 to 800 m{ell}/g and imply retardation factors of 60 to 500 using a fracture-flow model. Retardation factors inferred from uranium-series disequilibria and {sup 14}C ages in Culebra groundwaters alone are much lower ({approximately}10), implying that clays may contain a significant unreactive component of U. Such a possibility is corroborated by Rb/Sr ages; these imply long-term stability of the clays,with resetting occurring more than 250 Ma ago. Factor analysis and mass-balance calculations suggest, however, that Mg-rich clays are dissolving in Pleistocene-age groundwaters and/or are converting to Na-rich smectites, and that B and Li are taken up from the water by the clays. Apparently, the solution chemistry reflects gradual equilibration of clays with groundwater, but thus far the bulk of the clays remain structurally intact. Measurements of the distribution of U in the Culebra will be more meaningful if the inert and exchangeable components of the U content of the clays can be quantified. 26 refs., 3 figs., 2 tabs.

More Details

The role of chemical interactions in ion-solid processes

Dodson, Brian W.

Computer simulation of low-energy ion-solid processes has greatly broadened in scope in recent years. In particular, realistic descriptions of the ion-solid and solid-solid interactions can now be utilized. The molecular dynamics technique, in which the equations of motion of the interacting atoms are numerically integrated, can now be used to characterize ion-solid interactions in a range of model material systems. Despite practical limitations of this procedure, a number of substantial results have appeared. The available results are examined to investigate the qualitative influence that chemical interactions have on low-energy ion-solid processes. 26 refs., 4 figs.

More Details

Silicon nitride formation from a silane-nitrogen ECR (electron cyclotron resonance) plasma

Barbour, J.C.

Good quality, low temperature silicon nitride and oxynitride films were deposited downstream from an electron cyclotron resonance (ECR) plasma source using SiH{sub 4} and N{sub 2} gas mixtures. The Si/N ratio and H content in the deposited films were determined using Rutherford backscattering spectrometry (RBS)and elastic recoil detection (ERD). The H concentration was minimum for films with compositions closest to that of stoichiometric Si{sub 3}N{sub 4}. The optimum conditions for producing a stoichiometric Si{sub 3}N{sub 4}were: a SiH{sub 4}/N{sub 2} flow ratio between 0.1 and 0.2, and an electrically isolated sample far from the ECR source. Infrared absorption spectra showed that as the film composition changed from N rich to Si rich the dominant bonds associated with H changed from N-H to Si-H. The addition of O{sub 2} to the background gas formed an oxynitride with a low H content similar to the stoichiometric Si{sub 3}N{sub 4} 10 refs., 4 figs., 2 tabs.

More Details

A Josephson junction to FET high speed line driver made of TlCaBaCuO

Martens, J.S.; Ginley, D.S.; Beyer, J.B.; Nordman, J.E.; Hohenwarter, G.K.G.

We have used a Tl-Ca-Ba-Cu-O superconducting flux flow transistor (SFFT) as an active impedance converter between Josephson and FET circuitry. The input of the flux flow device is a control line of low impedance that can be driven by a tunnel junction. The output is the signal across the SFFT which is made of a parallel array of weak links. The output impedance is typically greater than 5 {Omega} with a maximum voltage swing of over 100 mV into a 50 {Omega} system. The switching of an all-Nb junction induced a 90 mV voltage swing at the FET input and over 200 mV at the FET output. The line driver can operate anywhere between 4.2K and 85K with minor changes in speed ({plus minus}5 ps) and output level ({plus minus}10 mV). The switching time measured was about 100 ps and was fixture limited. 13 refs., 5 figs.

More Details

Archimedes: A system that plans and executes mechanical assemblies

Strip, David R.

Archimedes is a prototype mechanical assembly system which generates and executes robot assembly programs from a CAD model input. The system addresses the unrealized potential for flexibility in robotic mechanical assembly applications by automating the programming task. Input is a solid model of the finished assembly. Parts relationships and geometric constraints are deduced from the solid model. A rule-based planner generates a generic'' assembly plan that satisfies the geometric constraints, as well as other constraints embodied in the rules. A retargetable plan compiler converts the generic plan into code specific to an application environment. Execution of the compiled plan in a workcell containing an Adept Two robot, a vision system, and other parts handling equipment will be shown on videotape.

More Details

Solid state radioluminescent sources: Mixed organic/inorganic hybrids

Renschler, Clifford L.

This concept brings a condensed source of tritium into close proximity with an inorganic phosphor. That source may thus become the equivalent of many atmospheres of tritium gas pressure. If both phosphor and tritium source material are optically clear, then a lamp's brightness may be made to scale with optical path length. Proof of principle of this concept has been demonstrated and will be described. A theoretical treatment is presented for the results here and for results from aerogel experiments.

More Details

Feasibility for development of a nuclear reactor pressure vessel flaw distribution: Sensitivity analyses and NDE (nondestructive evaluation) capability

Rosinski, S.T.

Pressurized water reactor pressure vessels operate under US Nuclear Regulatory Commission (NRC) rules and regulatory guides that are intended to maintain a low probability of vessel failure. The NRC has also addressed neutron embrittlement of pressurized water reactor pressure vessels by imposing regulations on plant operation. Plants failing to meet the operating criteria specified by these rules and regulations are required, among other things, to analytically demonstrate fitness for service in order to continue safe operation. The initial flaw size or distribution of initial vessel flaws is a key input to the required vessel integrity analyses. A fracture mechanics sensitivity study was performed to quantify the effect of the assumed flaw distribution on the predicted vessel performance under a specified pressurized thermal shock transient and to determine the critical crack size. Results of the analysis indicate that vessel performance in terms of the estimated probability of failure is very sensitive to the assumed flaw distribution. 20 refs., 3 figs., 2 tabs.

More Details

Solid state radioluminescent sources using zeolites

Renschler, Clifford L.

Inorganic zeolites show promise as an alternative to traditional tritium gas tube light sources. Greater proximity of tritium atoms and luminescing centers, as well as greater tritium loading density, have been obtained within the zeolite aluminosilicate matrix. Zeolites are in addition optically clear and radiation stable. The zeolite radioluminescence program is described. Procedures for obtaining light sources are presented and results are discussed. 12 refs., 1 fig.

More Details

Microstructures of cubic Al sub 2 O sub 3 precipitates in oxygen-implanted aluminum

Follstaedt, David M.

The microstructure of Al ion-implanted at room temperature with 17 at. % 0 has been characterized with TEM. The alloy has extremely small (1.5--3.5 nm) oxide precipitates whose crystal structure is interpreted to be a disordered version of {gamma}-Al{sub 2}O{sub 3} having a fcc lattice of O{sup 2{minus}} ions with Al{sup 3+} ions in random interstitial sites. The small sizes can account for the exceptionally high strength of as-implanted alloys: 2500--3300 MPa. Larger precipitates are found when the alloy is annealed 1/2 hour at 550{degree}C, which is consistent with its somewhat lower strength: 800--1600 MPa. 4 figs.

More Details

Solderability of environmentally exposed Sn-plated surfaces

Hosking, F.M.; Sorensen, N.R.

Solderability of Class II environmentally exposed Ni-Sn plated Cu substrates was evaluated with 60Sn-40Pb solder. Tin thickness were 10, 50, and 150 {mu}in. The 10 {mu}in. plating gave the smallest solder meniscus rise. A general decrease in contact angle, or increase in wettability, was observed with increasing Sn plating. The environmental exposures retarded the wetting rate and increased the time to maximum wetting, particularly with only 10 {mu}in. of Sn. Although the solderability of the 50 and 150 {mu}in. surfaces were not significantly affected by the test conditions, an intermediate plating thickness of 100 {mu}in. is preferred for processing flexibility. 13 refs., 6 figs., 1 tab.

More Details
Results 100301–100325 of 100,993
Results 100301–100325 of 100,993
Top