Publications

Results 97651–97675 of 100,993

Search results

Jump to search filters

The minimum pore size obtainable in a silica gel during drying

Brinker, C.J.

The pore size r{sub p} in a gel is determined by the extent of shrinkage of the gel network during drying. Shrinkage is driven by the collapse of the gel network in response to the capillary pressure P{sub c} exerted by the pore fluid. The extent of shrinkage depends on the balance between the capillary pressure P{sub c} in the pore fluid and the bulk modulus K{sub p} of the gel. The hydraulic pore radius, r{sub H} = 2V{sub p}/S{sub a}, where V{sub p} is the pore volume and S{sub a} is the apparent N{sub 2} BET surface area, is often used to characterize the pore size of a gel. A series of acid catalyzed silica gels dried in pore fluids with different {gamma}{sub lv}, showed that there is a limit to the minimum apparent r{sub H} obtainable in a gel, and when the volume fraction of porosity {phi} {le} 0.37, r{sub H} becomes constant and {approximately}0.8 nm. In contrast, experimental data show that the true pore size r{sub p} of gels continues to decrease when {phi} {le} 0.37. Analysis of their adsorption isotherms show that while r{sub H} apparently stays constant: (a) the BET C constant continues to increase, (b) the width and average of their pore size distributions continue to decrease, and (c) as shrinkage continues the gels eventually become non-porous to N{sub 2} at 77K but are still porous to CO{sub 2} at 273K. This paper reviews these results and addresses micropore formation in silica gels with the goal of determining how P{sub c} influences the final r{sub p}, and why r{sub p} and r{sub H} diverge when {phi} {le} 0.37.

More Details

Simulation of powder metal fabrication with high pressure gas atomization

Kuntz, David W.

A computational/analytical technique has been developed which models the physics of high pressure gas atomization. The technique uses an uncoupled approach, such that the gas flowfield is initially calculated with a commercially-available Navier-Stokes code. The liquid metal droplet breakup, dynamics, and thermodynamics, are then calculated using the pre-computed flowfield by a separate computer program written by the authors. The atomization code models the primary breakup of the liquid metal stream, tracks the droplets resulting from primary breakup through the flowfield until they undergo secondary breakup, and then tracks the subdroplets until they breakup, solidify, or leave the flowfield region of interest. The statistical properties of the metal powder produced are then computed from the characteristics of these droplets. Comparisons between experimental measurements and computations indicate that the Navier-Stokes code is predicting the gas flowfield well, and that the atomization code is properly modeling the physics of the droplet dynamics and breakup.

More Details

Fatigue case study and reliability analyses for wind turbines

Sutherland, Herbert J.

Modern wind turbines are fatigue critical machines used to produce electrical power. To insure long term, reliable operation, their structure must be optimized if they are to be economically viable. The fatigue and reliability projects in Sandia`s Wind Energy Program are developing the analysis tools required to accomplish these design requirements. The first section of the paper formulates the fatigue analysis of a wind turbine using a cumulative damage technique. The second section uses reliability analysis for quantifying the uncertainties and the inherent randomness associated with turbine performance and the prediction of service lifetimes. Both research areas are highlighted with typical results.

More Details

Workshop on transport for a common ion driver

Olson, Craig L.

This report contains research in the following areas related to beam transport for a common ion driver: multi-gap acceleration; neutralization with electrons; gas neutralization; self-pinched transport; HIF and LIF transport, and relevance to common ion driver; LIF and HIF reactor concepts and relevance to common ion driver; atomic physics for common ion driver; code capabilities and needed improvement.

More Details

Risk assessment methodologies for nuclear weapons compared to risk assessment methodologies for nuclear reactors

Benjamin, A.S.

There are major differences between the safety principles for nuclear weapons and for nuclear reactors. For example, a principal concern for nuclear weapons is to prevent electrical energy from reaching the nuclear package during accidents produced by crashes, fires, and other hazards, whereas the foremost concern for nuclear reactors is to maintain coolant around the core in the event of certain system failures. Not surprisingly, new methods have had to be developed to assess the risk from nuclear weapons. These include fault tree transformations that accommodate time dependencies, thermal and structural analysis techniques that are fast and unconditionally stable, and Monte-Carlo-based sampling methods that incorporate intelligent searching. This paper provides an overview of the new methods for nuclear weapons, compares them with existing methods for nuclear reactors, identifies some of their dual-use characteristics, and discusses ongoing developmental activities.

More Details

A simple and efficient procedure for polyhedral assembly partitioning under infinitesimal motions

Wilson, Rodney K.

The authors study the following problem: given a collection A of polyhedral parts in 3D, determine whether there exists a subset S of the parts that can be moved as a rigid body by an infinitesimal translation and rotation, without colliding with the rest of the parts, A/S. A negative result implies that the object whose constituent parts are the collection A cannot be taken apart with two hands. A positive result, together with the list of movable parts in S and a direction of motion for S, can be used by an assembly sequence planner. This problem has attracted considerable attention within and outside the robotics community. They devise an efficient algorithm to solve this problem. The solution is based on the ability to focus on selected portions of the tangent space of rigid motions and efficiently access these portions. The algorithm is complete (in the sense that it is guaranteed to find a solution if one exists), simple, and improves significantly over the best previously known solutions. The authors report experimental results with an implementation of their algorithm.

More Details

Successful remediation of four uranium calibration pits at Technical Area II, Sandia National Laboratories, Albuquerque, New Mexico, USA

Conway, R.

The first remediation of an Environmental Restoration (ER) Project site at Sandia National Laboratories (SNL) was successfully conducted in May and June 1994 at Technical Area II. The removal action involved four Uranium Calibration Pits (UCPs) filled with radioactive or hazardous materials. The concrete culvert pits were used to test and calibrate borehole radiometric logging tools for uranium exploration. The removal action consisted of excavating and containerizing the pit contents and contaminated soil beneath the culverts, removing the four culverts, and backfilling the excavation. Each UCP removal had unique complexities. Sixty 208-L drums of solid radioactive waste and eight 208-L drums of liquid hazardous waste were generated during the VCM. Two of the concrete culverts will be disposed as radioactive waste and two as solid waste. Uranium-238 was detected in UCP-2 ore material at 746 pci/g, and at 59 pci/g in UCP-1 silica sand. UCP-4 was empty; sludge from UCP-3 contained 122 mg/L (ppm) chromium.

More Details

Detailed characterization and preliminary adsorption model for materials for an intermediate-scale reactive-transport experiment

Siegel, Malcolm

An experiment involving migration of fluid and tracers (Li, Br, Ni) through a 6-m-high x 3-m-dia caisson Wedron 510 sand, is being carried out for Yucca Mountain Site Characterization Project. Sand`s surface chemistry of the sand was studied and a preliminary surface-complexation model of Ni adsorption formulated for transport calculations. XPS and leaching suggest that surface of the quartz sand is partially covered by thin layers of Fe-oxyhydroxide and Ca-Mg carbonate and by flakes of kaolinite. Ni adsorption by the sand is strongly pH-dependent, showing no adsorption at pH 5 and near-total adsorption at pH 7. Location of adsorption edge is independent of ionic strength and dissolved Ni concentration; it is shifted to slightly lower pH with higher pCO2 and to slightly higher pH by competition with Li. Diminished adsorption at alkiline pH with higher pCO2 implies formation of dissolved Ni-carbonato complexes. Ni adsorption edges for goethite and quartz, two components of the sand were also measured. Ni adsorption on pure quartz is only moderately pH-dependent and differs in shape and location from that of the sand, whereas Ni adsorption by goethite is strongly pH-dependent. A triple-layer surface-complexation model developed for goethite provides a good fit to the Ni-adsorption curve of the sand. Based on this model, the apparent surface area of the Fe-oxyhydroxide coating is estimated to be 560 m{sup 2}/g, compatible with its occurrence as amorphous Fe-oxyhydroxide. Potentiometric titrations on sand also differ from pure quartz and suggest that effective surface area of sand may be much greater than that measured by N{sub 2}-BET gas adsorption. Attempts to model the adsorption of bulk sand in terms of properties of pure end member components suggest that much of the sand surface is inert. Although the exact Ni adsorption mechanisms remain ambiguous, this preliminary adsorption model provides an initial set of parameters that can be used in transport calculations.

More Details

Sol-gel strategies for amorphous inorganic membranes exhibiting molecular sieving characteristics

Brinker, C.J.

We have used several sol-gel strategies to prepare supported inorganic membranes by a process that combines the features of slip-casting and dip-coating. To be viable the deposited membranes must exhibit both high flux and high selectivity. For porous membranes these requirements are met by extremely thin, defect-free porous films exhibiting a narrow size distribution of very small pores. This paper considers the use of polymeric silica and hybrid-organosilyl precursor sols in the context of the underlying physics and chemistry of the membrane deposition process. Since the average membrane pore size is ultimately established by the collapse of the gel network upon drying, it is necessary to promote polymer interpenetration and collapse during membrane deposition in order to achieve the very small pore sizes necessary for molecular sieving. For polymeric sols, this is accomplished using rather weakly branched polymers characterized by fractal dimension D < 1.5 under deposition conditions in which the silica condensation rate is minimized. By analogy to organic polymer sols and gels, we believe that the breadth of the pore size distribution can be influenced by the occurrence of micro-phase separation during membrane deposition. Minimization of the condensation rate not only fosters polymer collapse but should inhibit phase separation, leading to a narrower pore size distribution. The formation of microporosity through collapse of the gel network requires that small pores are achieved at the expense of membrane porosity. Incorporation of organic template ligands within a dense silica matrix followed by their removal allows us to independently control pore size and pore volume through the size and volume fraction of the organic template. Such strategies can be used to create microporous films with large volume fraction porosities.

More Details

STDAC: Solar Thermal Design Assistance Center annual report fiscal year 1994

Menicucci, David F.

The Solar Thermal Design Assistance Center (STDAC) at Sandia is a resource provided by the DOE Solar Thermal Program. The STDAC`s major objective is to accelerate the use of solar thermal systems by providing direct technical assistance to users in industry, government, and foreign countries; cooperating with industry to test, evaluate, and develop renewable energy systems and components; and educating public and private professionals, administrators, and decision makers. This FY94 report highlights the activities and accomplishments of the STDAC. In 1994, the STDAC continued to provide significant direct technical assistance to domestic and international organizations in industry, government, and education, Applying solar thermal technology to solve energy problems is a vital element of direct technical assistance. The STDAC provides information on the status of new, existing, and developing solar technologies; helps users screen applications; predicts the performance of components and systems; and incorporates the experience of Sandia`s solar energy personnel and facilities to provide expert guidance. The STDAC directly enhances the US solar industry`s ability to successfully bring improved systems to the marketplace. By collaborating with Sandia`s Photovoltaic Design Assistance Center and the National Renewable Energy Laboratory the STDAC is able to offer each customer complete service in applying solar thermal technology. At the National Solar Thermal Test Facility the STDAC tests and evaluates new and innovative solar thermal technologies. Evaluations are conducted in dose cooperation with manufacturers, and the results are used to improve the product and/or quantify its performance characteristics. Manufacturers, in turn, benefit from the improved design, economic performance, and operation of their solar thermal technology. The STDAC provides cost sharing and in-kind service to manufacturers in the development and improvement of solar technology.

More Details

High silicon content silylating reagents for dry-developed positive-tone resists for extreme ultraviolet (13.5 nm) and deep ultraviolet (248 nm) microlithography

Wheeler, David R.

Recent results in the use of disilanes as silylating reagents for near-surface imaging with deep-UV (248 nm) and EUV (13.5 nm) lithography are reported. A relatively thin imaging layer of a photo-cross-linking resist is spun over a thicker layer of hard-baked resist that functions as a planarizing layer and antireflective coating. Photoinduced acid generation and subsequent heating crosslinks and renders exposed areas impermeable to an aminodisilane that reacts with the unexposed regions. Subsequent silylation and reactive ion etching afford a positive-tone image. The use of disilanes introduces a higher concentration of silicon into the polymer than is possible with silicon reagents that incorporate only one silicon atom per reactive site. The higher silicon content in the silylated polymer increases etching selectivity between exposed and unexposed regions and thereby increases the contrast. Additional improvements that help to minimize flow during silylation are also discussed, including the addition of bifunctional disilanes. We have resolved high aspect ratio, very high quality 0.20 {mu}m line and space patterns at 248 nm with a stepper having a numerical aperture (NA)= 0.53, and have resolved {<=} 0.15 {mu}m line and spaces at 13.5 nm.

More Details

Atomic oxygen interaction with nickel multilayer and antimony oxide doped MoS{sub 2} films

Dugger, Michael T.

Sputtered MoS{sub 2} is a solid lubricant capable of ultralow friction coefficients (below 0.05) load-bearing capacity. Since it exhibits low friction in vacuum, low outgassing rate, is non-migrating and lacks organic binders, this material is an attractive lubricant for space mechanisms. To exploit these new materials to their fullest potential, designers of space-based motion systems require data on the effects of atomic oxygen exposure on dense, sputtered MoS{sub 2}. This paper describes the effects of atomic oxygen in low earth orbit on the friction and surface composition of sputtered MoS{sub 2} films. Sputtered multilayer films of MoS{sub 2} with nickel (0.7 nm Ni per 10 nm MoS{sub 2}, for 1 {mu}m total film thickness), and MoS{sub 2} cosputtered with antimony oxide (nominally 2 {mu}m thick) were exposed to 2.2 to 2.5 x 10{sup 20} oxygen/cm{sup 2} over a period of 42.25 hours in earth orbit on the United States space shuttle. Identical specimens were kept as controls in desiccated storage for the duration of the mission, and another set was exposed to an equivalent fluence of atomic oxygen in the laboratory. The friction coefficient in air and vacuum, and the composition of worn surfaces, were determined prior to the shuttle flight and again after the shuttle flight. Results are described.

More Details

High heat flux testing capabilities at Sandia National Laboratories - New Mexico

Youchison, Dennis L.

High heat flux testing for the United States fusion power program is the primary mission of the Plasma Materials Test Facility (PMTF) located at Sandia National Laboratories - New Mexico. This facility, which is owned by the United States Department of Energy, has been in operation for over 17 years and has provided much of the high heat flux data used in the design and evaluation of plasma facing components for many of the world`s magnetic fusion, tokamak experiments. In addition to domestic tokamaks such as Tokamak Fusion Test Reactor (TFTR) at Princeton and the DIII-D tokamak at General Atomics, components for international experiments like TEXTOR, Tore-Supra, and JET also have been tested at the PMTF. High heat flux testing spans a wide spectrum including thermal shock tests on passively cooled materials, thermal response and thermal fatigue tests on actively cooled components, critical heat flux-burnout tests, braze reliability tests and safety related tests. The objective of this article is to provide a brief overview of the high heat flux testing capabilities at the PMTF and describe a few of the experiments performed over the last year.

More Details

Thermal fatigue testing of a diffusion-bonded beryllium divertor mock-up under ITER relevant conditions

Youchison, Dennis L.

Thermal response and thermal fatigue tests of four 5 mm thick beryllium tiles on a Russian divertor mock-up were completed on the Electron Beam Test System at Sandia National Laboratories. The beryllium tiles were diffusion bonded onto an OFHC copper saddleblock and a DSCu (MAGT) tube containing a porous coating. Thermal response tests were performed on the tiles to an absorbed heat flux of 5 MW/m{sup 2} and surface temperatures near 300{degrees}C using 1.4 MPa water at 5.0 m/s flow velocity and an inlet temperature of 8-15{degrees}C. One tile was exposed to incrementally increasing heat fluxes up to 9.5 MW/m{sup 2} and surface temperatures up to 690{degrees}C before debonding at 10 MW/m{sup 2}. A third tile debonded after 9200 thermal fatigue cycles at 5 MW/m{sup 2}, while another debonded after 6800 cycles. In all cases, fatigue failure occurred in the intermetallic layers between the beryllium and copper. No fatigue cracking of the bulk beryllium was observed. During thermal cycling, a gradual loss of porous coating produced increasing sample temperatures. These experiments indicate that diffusion-bonded beryllium tiles can survive several thousand thermal cycles under ITER relevant conditions without failure. However, the reliability of the diffusion bonded Joint remains a serious issue.

More Details

Autonomous, teleoperated, and shared control of robot systems

Anderson, Robert J.

This paper illustrates how different modes of operation such as bilateral teleoperation, autonomous control, and shared control can be described and implemented using combinations of modules in the SMART robot control architecture. Telerobotics modes are characterized by different ``grids`` of SMART icons, where each icon represents a portion of run-time code that implements a passive control law. By placing strict requirements on the module`s input-output behavior and using scattering theory to develop a passive sampling technique, a flexible, expandable telerobot architecture is achieved. An automatic code generation tool for generating SMART systems is also described.

More Details

Transportation technology at Sandia

Mora, Carl J.

Industrial and military activities in the US produce large amounts of hazardous mixed waste, which includes both radioactive and toxic substances. The already overburdened environment is faced with the task of safely disposing of these complex wastes. A very important aspect of this effort is the safe and economical transportation of radioactive and toxic chemical wastes to projected repositories. Movement of wastes to the repository sites is accomplished by a combination of truck, rail, ship, and air. The DOE directs transportation activities including cask development technology for use in single or multimode transport. Sandia National Laboratories` Transportation Technology programs provide the technology and know-how to support DOE in achieving safe, efficient, and economical packaging and transportation of nuclear and other hazardous waste materials. This brochure describes the Transportation Technology programs and the specialized techniques and capabilities they offer to prospective users.

More Details

Fifth wheel installation, S97556, Issue H

O'Canna, Myra L.

This report consists of one engineering drawing showing the design of the Fifth Wheel System for a semi-tractor trailer truck. Notes on the drawing give instructions for installation of some items, references to other drawings and instructions, and testing procedures.

More Details

Fifth wheel modification assembly, Issue U

O'Canna, Myra L.

This report consists of one engineering drawing showing modifications to the Fifth Wheel System for a semi-tractor trailer truck. Notes give instructions for installation of some items, where other items may be purchased, testing instructions, and shipping instructions.

More Details

A review of research and methods for producing high-consequence software

Dalton, Larry J.

The development of software for use in high-consequence systems mandates rigorous (formal) processes, methods, and techniques to improve the safety characteristics of those systems. This paper provides a brief overview of current research and practices in high-consequence software, including applied design methods. Some of the practices that are discussed include: fault tree analysis, failure mode effects analysis, petri nets, both hardware and software interlocks, n-version programming, Independent Vulnerability Analyses, and watchdogs. Techniques that offer improvement in the dependability of software in high-consequence systems applications are identified and discussed. Limitations of these techniques are also explored. Research in formal methods, the cleanroom process, and reliability models are reviewed. In addition, current work by several leading researchers as well as approaches being used by leading practitioners are examined.

More Details

Evaluation of power production from the solar electric generating systems at Kramer Junction: 1988 to 1993

Kolb, Gregory J.

The five Solar Electric Generating Systems (SEGS) at Kramer Junction, California, now have nearly 30 years of cumulative operating experience. These 30 MW plants employ parabolic trough technology originally deployed by LUZ International in the late 1980`s and are now managed, operated and maintained by the Kramer Junction Company. In this paper, Sandia National Laboratories performed an analysis of the annual energy production from the five plants. Annual solar-to-electric conversion efficiencies are calculated and the major factors that influenced the results are presented. The generally good efficiencies are primarily attributed to the excellent equipment availabilities achieved at all plants.

More Details

Retrofitting a fine-pointing system to satellite optics

Woods, R.O.

This paper describe a system that was added to an existing satellite-borne telescope design for the purpose of compensating the boresight errors that had been observed in earlier flights of similar instruments. Those errors had been found to be caused by thermal distortion of the spaceframe. This retrofit design was subject to severe volume restrictions because it was fitted into an already tightly-packaged instrument envelope. It was found practical to improve the basic design by converting a redundant structure into a statically-determinate one. It was also possible to use portions of the mechanical actuation system to facilitate the position encoding needed for computer interfacing.

More Details

Salt dissolution sinkhole at the Weeks Island, Louisiana, Strategic Petroleum Reserve storage site

Neal, J.T.

A sinkhole was first observed in May 1992 over the outer edge of the two-tiered former salt mine that was converted for oil storage by the US Strategic Petroleum Reserve (SPR). Results of diagnostic studies which included geophysical, geochemical, drilling, and hydrological methods suggest a direct connection exists between the surface collapse area and the underground mine. The connection was confirmed by correlative measurements of sediment slump rates, piezometric surface deflection, and brine influx rates into the mine. The dissolution of salt below the sinkhole that initiated the leak into the mine was likely caused by several confluent geologic processes, and exacerbated by mining-induced stresses that created fractures which severed as hydrologic flowpaths. Modeling studies of mine stresses show that years of tensional stresses may be required before cracking begins to occur, but once begun can continue to develop, and relieve the stress in that specific regime. The crack regime creates the avenue for incursion of groundwater, very slowly initially, but gradually enlarging as undersaturated groundwater dissolves salt on the sides of the crack. Mitigative measures include increasing the mine pressurization, slowing the dissolution by injecting brine into the sinkhole throat, and permeation grouting in hydrologic flowpaths.

More Details
Results 97651–97675 of 100,993
Results 97651–97675 of 100,993
Top