The use of an electrochemical dissolution process is shown to remove the recast layer contamination from the surfaces of electrical-discharge-machining cut components, as well as the interior exposed surfaces of the structure. The solution chemistry, cell potential, and exposure time are all relevant interdependent variables. Optimization of the electrode geometry should be made for each type of component. For the case of Cu-Zn recast contamination of 300-series alloy components, surface composition analysis indicates that complete electrochemical dissolution is achieved using a dilute solution of nitric acid (HNO3). For example, electrochemical dissolution of the Cu-Zn recast is accomplished at 1.2 V cell potential using a 20% nitric solution and an exposure time of 4 h. The use of a nitric acid bath was specifically chosen since it’s chemically compatible and will not degrade the host alloy or the component. In sum, an electrochemically driven dissolution process can be tailored to remove of the recast contamination without affecting the integrity of the host component structure and its dimensional tolerances.
The localized corrosion of laser surface melted (LSM) 316L stainless steel is investigated by a combination of potentiodynamic anodic polarization in 0.1 M HCl and microscopic investigation of the initiation and propagation of localized corrosion. The pitting potential of LSM 316L is significantly lower than the pitting potential of wrought 316L. The LSM microstructure is highly banded as a consequence of the high laser power density and high linear energy density. The bands are composed of zones of changing modes of solidification, cycling between very narrow regions of primary austenite solidification and very wide regions of primary ferrite solidification. Pits initiate in the outer edge of each band where the mode of solidification is primary austenite plane front solidification and primary austenite cellular solidification. The primary austenite regions have low chromium concentration (and possibly low molybdenum concentration), which explains their susceptibility to pitting corrosion. The ferrite is enriched in chromium, which explains the absence of pitting in the primary ferrite regions. The presence of the low chromium regions of primary austenite solidification explains the lower pitting resistance of LSM 316L relative to wrought 316L. The influence of banding on localized corrosion is applicable to other rapidly solidified processes such as additive manufacturing.
The microstructures of 316 L stainless steel created by rapid solidification are investigated by comparing the similar microstructures of individual hatches of directed energy deposition additive manufacturing (DED-AM) and those of single, laser surface-melted tracks formed on a solid plate. High recoil pressure, which is exponentially dependent on the laser beam power density, induces convection of the melt pool, which causes formation of microstructural bands in the as-solidified microstructure. The microstructural bands are associated with changes in the chromium concentration and are a significant component of the inhomogeneous microstructure of DED-AM.
To identify the critical issues that affect the evolution of microstructure during additive manufacturing, we investigated the influence of process parameters on the evolution of the dimensional and surface quality, microstructure, internal defects, and mechanical properties in 316L stainless steel (SS) components fabricated using laser engineered net shaping (LENS®), a directed energy deposition (DED) additive manufacturing (AM) technique. The results show that the accumulation of un-melted powder particles on the side walls of deposited sections can be avoided by selecting a laser under-focused condition. Moreover, we report that the variation of melt pool width is more sensitive to laser power than to the depth of the melt pool. The formation of a so-called “hierarchical” microstructure with cellular morphology is attributable to a combination of layer deposition and rapid solidification, which are characteristics of AM. Finally, we discuss microstructure evolution and defect formation, particularly the formation of multiple interfaces and the presence of un-melted powder particles and pores, in light of the dynamic convective fluid flow and rapid solidification that occur in the melt pool. X-ray computed tomography (X-CT) was used to precisely map the spatial distribution of pores in the DED components. The evolution of microstructure during DED is discussed in the context of related thermal phenomena in an effort to provide fundamental insight into the mechanisms that govern defect formation.
Laser Engineered Net Shaping (LENS) and Powder Bed Fusion (PBF) are 3-D additive manufacturing (AM) processes. They are capable of printing metal parts with complex geometries and dimensions effectively. Studies have shown that AM processes create metals with distinctive microstructure features and material properties, which are highly dependent on the processing parameters. The mechanical properties of an AM material may appear to be similar to the corresponding wrought material in some way. This investigation focuses on the relationships among AM process, microstructure features, and material properties. The study involves several AM SS316L components made from 3D LENS and PBF printing. Specimens were taken from different locations and orientations of AM components to obtain the associated tensile properties, including yield, strength, and ductility, and to conduct microstructure analyses.
We investigate the process-structure-property relationships for 316L stainless steel prototyping utilizing 3-D laser engineered net shaping (LENS), a commercial direct energy deposition additive manufacturing process. The study concluded that the resultant physical metallurgy of 3-D LENS 316L prototypes is dictated by the interactive metallurgical reactions, during instantaneous powder feeding/melting, molten metal flow and liquid metal solidification. The study also showed 3-D LENS manufacturing is capable of building high strength and ductile 316L prototypes due to its fine cellular spacing from fast solidification cooling, and the well-fused epitaxial interfaces at metal flow trails and interpass boundaries. However, without further LENS process control and optimization, the deposits are vulnerable to localized hardness variation attributed to heterogeneous microstructure, i.e., the interpass heat-affected zone (HAZ) from repetitive thermal heating during successive layer depositions. Most significantly, the current deposits exhibit anisotropic tensile behavior, i.e., lower strain and/or premature interpass delamination parallel to build direction (axial). This anisotropic behavior is attributed to the presence of interpass HAZ, which coexists with flying feedstock inclusions and porosity from incomplete molten metal fusion. The current observations and findings contribute to the scientific basis for future process control and optimization necessary for material property control and defect mitigation.
Directed energy deposition (DED) is a type of additive manufacturing (AM) process; Laser Engineered Net Shaping (LENS) is a commercial DED process. We are developing LENS technology for printing 316L stainless steel components for structural applications. It is widely known that material properties of AM components are process dependent, attributed to different molten metal incorporation and thermal transport mechanisms. This investigation focuses on process-structure-property relationships for LENS deposits for enabling the process development and optimization to control material property. We observed interactions among powder melting, directional molten metal flow, and the molten metal solidification. The resultant LENS induced microstructure found to be dictated by the process-related characteristics, i.e., interpass boundaries from multi-layer deposition, molten metal flow lines, and solidification dendrite cells. Each characteristic bears the signature of the unique localized thermal history during deposition. Correlation observed between localized thermal transport, resultant microstructure, and its subsequent impact on the mechanical behavior of the current 316L is discussed. We also discuss how the structures of interpass boundaries are susceptible to localized recrystallization, grain growth and/or defect formation, and therefore, heterogeneous mechanical properties due to the adverse presence of unmelted powder inclusions.