An experimental program is being conducted to study a proposed approach for oil reintroduction in the Strategic Petroleum Reserve (SPR). The goal is to assess whether useful oil is rendered unusable through formation of a stable oil-brine emulsion during reintroduction of degassed oil into the brine layer in storage caverns. This report documents the first stage of the program, in which simulant liquids are used to characterize the buoyant plume that is produced when a jet of crude oil is injected downward from a tube into brine. The experiment consists of a large transparent vessel that is a scale model of the proposed oil injection process at the SPR. An oil layer is floated on top of a brine layer. Silicon oil (Dow Corning 200{reg_sign} Fluid, 5 cSt) is used as the simulant for crude oil to allow visualization of the flow and to avoid flammability and related concerns. Sodium nitrate solution is used as the simulant for brine because it is not corrosive and it can match the density ratio between brine and crude oil. The oil is injected downward through a tube into the brine at a prescribed depth below the oil-brine interface. Flow rates are determined by scaling to match the ratio of buoyancy to momentum between the experiment and the SPR. Initially, the momentum of the flow produces a downward jet of oil below the tube end. Subsequently, the oil breaks up into droplets due to shear forces, buoyancy dominates the flow, and a plume of oil droplets rises to the interface. The interface is deflected upward by the impinging oil-brine plume. Two different diameter injection tubes were used (1/2-inch and 1-inch OD) to vary the scaling. Use of the 1-inch injection tube also assured that turbulent pipe flow was achieved, which was questionable for lower flow rates in the 1/2-inch tube. In addition, a 1/2-inch J-tube was used to direct the buoyant jet upwards rather than downwards to determine whether flow redirection could substantially reduce the oil-plume size and the oil-droplet residence time in the brine. Reductions of these quantities would inhibit emulsion formation by limiting the contact between the oil and the brine. Videos of this flow were recorded for scaled flow rates that bracket the equivalent pumping rates in an SPR cavern. Image-processing analyses were performed to quantify the penetration depth of the oil jet, the width of the jet, and the deflection of the interface. The measured penetration depths are shallow, as predicted by penetration-depth models, in agreement with the assumption that the flow is buoyancy-dominated, rather than momentum-dominated. The turbulent penetration depth model provided a good estimate of the measured values for the 1-inch injection tube but overpredicted the penetration depth for the 1/2-inch injection tube. Adding a virtual origin term would improve the prediction for the 1/2-inch tube for low to nominal injection flow rates but could not capture the rollover seen at high injection flow rates. As expected, the J-tube yielded a much narrower plume because the flow was directed upward, unlike the downward-oriented straight-tube cases where the plume had to reverse direction, leading to a much wider effective plume area. Larger surface deflections were caused by the narrower plume emitted from the J-tube. Although velocity was not measured in these experiments, the video data showed that the J-tube plume was clearly faster than those emitted from the downward-oriented tubes. These results indicate that oil injection tube modifications could inhibit emulsion formation by reducing the amount of contact (both time and area) between the oil and the brine. Future studies will employ crude oil, saturated brine, and interfacial solids (sludge) from actual SPR caverns.
The hydrostatically induced ferroelectric(FE)-to-antiferroelectric(AFE) phase transformation for chemically prepared niobium modified PZT 95/5 ceramics was studied as a function of density and pore former type (Lucite or Avicel). Special attention was placed on the effect of different pore formers on the charge release behavior associated with the FE-to-AFE phase transformation. Within the same density range (7.26 g/cm3 to 7.44 g/cm3), results showed that ceramics prepared with Lucite pore former exhibit a higher bulk modulus and a sharper polarization release behavior than those prepared with Avicel. In addition, the average transformation pressure was 10.7% greater and the amount of polarization released was 2.1% higher for ceramics with Lucite pore former. The increased transformation pressure was attributed to the increase of bulk modulus associated with Lucite pore former. Data indicated that a minimum volumetric transformational strain of -0.42% was required to trigger the hydrostatically induced FE-to-AFE phase transformation. This work has important implications for increasing the high temperature charge output for neutron generator power supply units.
This document describes the design, fabrication, and testing of the SNL Data Encryption Standard (DES) ASIC. This device was fabricated in Sandia's Microelectronics Development Laboratory using 0.6 {micro}m CMOS technology. The SNL DES ASIC was modeled using VHDL, then simulated, and synthesized using Synopsys, Inc. software and finally IC layout was performed using Compass Design Automation's CAE tools. IC testing was performed by Sandia's Microelectronic Validation Department using a HP 82000 computer aided test system. The device is a single integrated circuit, pipelined realization of DES encryption and decryption capable of throughputs greater than 6.5 Gb/s. Several enhancements accommodate ATM or IP network operation and performance scaling. This design is the latest step in the evolution of DES modules.
Athermal, tethered chains are modeled with Density Functional (DFT) theory for both the explicit solvent and continuum solvent cases. The structure of DFT is shown to reduce to Self-Consistent-Field (SCF) theory in the incompressible limit where there is symmetry between solvent and monomer, and to Single-Chain-Mean-Field (SCMF) theory in the continuum solvent limit. We show that by careful selection of the reference and ideal systems in DFT theory, self-consistent numerical solutions can be obtained, thereby avoiding the single chain Monte Carlo simulation in SCMF theory. On long length scales, excellent agreement is seen between the simplified DFT theory and Molecular Dynamics simulations of both continuum solvents and explicit-molecule solvents. In order to describe the structure of the polymer and solvent near the surface it is necessary to include compressibility effects and the nonlocality of the field.
A fundamental challenge for all communication systems, engineered or living, is the problem of achieving efficient, secure, and error-free communication over noisy channels. Information theoretic principals have been used to develop effective coding theory algorithms to successfully transmit information in engineering systems. Living systems also successfully transmit biological information through genetic processes such as replication, transcription, and translation, where the genome of an organism is the contents of the transmission. Decoding of received bit streams is fairly straightforward when the channel encoding algorithms are efficient and known. If the encoding scheme is unknown or part of the data is missing or intercepted, how would one design a viable decoder for the received transmission? For such systems blind reconstruction of the encoding/decoding system would be a vital step in recovering the original message. Communication engineers may not frequently encounter this situation, but for computational biologists and biotechnologist this is an immediate challenge. The goal of this work is to develop methods for detecting and reconstructing the encoder/decoder system for engineered and biological data. Building on Sandia's strengths in discrete mathematics, algorithms, and communication theory, we use linear programming and will use evolutionary computing techniques to construct efficient algorithms for modeling the coding system for minimally errored engineered data stream and genomic regulatory DNA and RNA sequences. The objective for the initial phase of this project is to construct solid parallels between biological literature and fundamental elements of communication theory. In this light, the milestones for FY2003 were focused on defining genetic channel characteristics and providing an initial approximation for key parameters, including coding rate, memory length, and minimum distance values. A secondary objective addressed the question of determining similar parameters for a received, noisy, error-control encoded data set. In addition to these goals, we initiated exploration of algorithmic approaches to determine if a data set could be approximated with an error-control code and performed initial investigations into optimization based methodologies for extracting the encoding algorithm given the coding rate of an encoded noise-free and noisy data stream.
Ceramic packaging is crucial to the development of MEMS-based microsystems. It is an enabling technology, giving the ability to build complex packages that combine MEMS, electronics, optics, and sensors in a compact volume. In addition, ceramic hermetic packaging has a long history of providing protection to the enclosed devices, even under harsh conditions. These capabilities are being used at Sandia to package complex, MEMS-based microsystems. Looking ahead, ceramic packaging is developing new capabilities important to microsystems, such as the addition of fluidic channels. These developments will make ceramic packaging a viable option for a wide variety of compact, highly integrated microsystems. However, MEMS, particularly surface micromachines, have new reliability concerns that ceramic packaging needs to address. One example is stiction, where small amounts of water can generate surface forces large enough to cause parts to stick together. This demonstrates the need to measure and control the internal environment with greater precision than has been required in the past. Despite these challenges, it is clear that ceramic packaging will be a key technology for complex microsystems in the future.
The sintering behavior of LTCC/silver-palladium conductor bi-layers was studied in situ using video observation. This allowed simultaneous measurement of length of the bi-layer, its curvature, as well as the thickness of each of the layers. The free sintering behavior of the materials was also characterized using in situ video observation. The mismatch in the shrinkage kinetics between the LTCC and the conductors, which had the same composition but differed in that one was a mixture of Ag and Pd and the other was an alloy, caused the bi-layers to curve and the layers to have anisotropic shrinkage. The curvature of the bi-layers during sintering was very different for the two conductors due to their greatly different free sintering behavior. The uniaxial viscosity of the LTCC and the Ag-Pd alloy material were measured using cyclic loading dilatometry. The free sintering and uniaxial viscosity results were fit by empirical equations that were then used to model the shrinkage behavior of the bi-layers using a simple analytical model that neglects the bending stresses. The predictions of the model were consistent with the measured in-plane shrinkage. However, the thickness shrinkage predictions of the model did not fit the data as well. When bi-layers were sintered such that warping was constrained so that there were no bending stresses, the thickness shrinkage behavior was nearly the same as when warping occurred. Finally, the viscous analog of the elastic bi-layer curvature equation fit the bi-layer curvature data reasonably well.
This report presents the implementation of a stateless scheme for Faithful Execution, the design for which is presented in a companion report, ''Principles of Faithful Execution in the Implementation of Trusted Objects'' (SAND 2003-2328). We added a simple cryptographic capability to an already simplified class loader and its associated Java Virtual Machine (JVM) to provide a byte-level implementation of Faithful Execution. The extended class loader and JVM we refer to collectively as the Sandia Faithfully Executing Java architecture (or JavaFE for short). This prototype is intended to enable exploration of more sophisticated techniques which we intend to implement in hardware.
We begin with the following definitions: Definition: A trusted volume is the computing machinery (including communication lines) within which data is assumed to be physically protected from an adversary. A trusted volume provides both integrity and privacy. Definition: Program integrity consists of the protection necessary to enable the detection of changes in the bits comprising a program as specified by the developer, for the entire time that the program is outside a trusted volume. For ease of discussion we consider program integrity to be the aggregation of two elements: instruction integrity (detection of changes in the bits within an instruction or block of instructions), and sequence integrity (detection of changes in the locations of instructions within a program). Definition: Faithful Execution (FE) is a type of software protection that begins when the software leaves the control of the developer and ends within the trusted volume of a target processor. That is, FE provides program integrity, even while the program is in execution. (As we will show below, FE schemes are a function of trusted volume size.) FE is a necessary quality for computing. Without it we cannot trust computations. In the early days of computing FE came for free since the software never left a trusted volume. At that time the execution environment was the same as the development environment. In some circles that environment was referred to as a ''closed shop:'' all of the software that was used there was developed there. When an organization bought a large computer from a vendor the organization would run its own operating system on that computer, use only its own editors, only its own compilers, only its own debuggers, and so on. However, with the continuing maturity of computing technology, FE becomes increasingly difficult to achieve
Sandia National Laboratories, New Mexico (SNL/NM) is a government-owned, contractor-operated facility overseen by the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA) through the Sandia Site Office (SSO), Albuquerque, New Mexico. Sandia Corporation, a wholly-owned subsidiary of Lockheed Martin Corporation, operates SNL/NM. This annual report summarizes data and the compliance status of Sandia Corporation's environmental protection and monitoring programs through December 31, 2002. Major environmental programs include air quality, water quality, groundwater protection, terrestrial surveillance, waste management, pollution prevention (P2), environmental restoration (ER), oil and chemical spill prevention, and the National Environmental Policy Act (NEPA). Environmental monitoring and surveillance programs are required by DOE Order 5400.1, General Environmental Protection Program (DOE 1990) and DOE Order 231.1, Environment, Safety, and Health Reporting (DOE 1996).
Tonopah Test Range (TTR) in Nevada and Kauai Test Facility (KTF) in Hawaii are government-owned, contractor-operated facilities operated by Sandia Corporation, a subsidiary of Lockheed Martin Corporation. The U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA), through the Sandia Site Office (SSO), in Albuquerque, NM, oversees TTR and KTF's operations. Sandia Corporation conducts operations at TTR in support of DOE/NNSA's Weapons Ordnance Program and has operated the site since 1957. Westinghouse Government Services subcontracts to Sandia Corporation in administering most of the environmental programs at TTR. Sandia Corporation operates KTF as a rocket preparation launching and tracking facility. This Annual Site Environmental Report (ASER) summarizes data and the compliance status of the environmental protection and monitoring program at TTR and KTF through Calendar Year (CY) 2002. The compliance status of environmental regulations applicable at these sites include state and federal regulations governing air emissions, wastewater effluent, waste management, terrestrial surveillance, and Environmental Restoration (ER) cleanup activities. Sandia Corporation is responsible only for those environmental program activities related to its operations. The DOE/NNSA, Nevada Site Office (NSO) retains responsibility for the cleanup and management of ER TTR sites. Currently, there are no ER Sites at KTF. Environmental monitoring and surveillance programs are required by DOE Order 5400.1, General Environmental Protection Program (DOE 1990) and DOE Order 231.1, Environment, Safety, and Health Reporting (DOE 1996).
Evidence for the existence of discrete sub-movements underlying continuous human movement has motivated many attempts to "extract" them. Although they produce visually convincing results, all of the methodologies that have been employed are prone to produce spurious decompositions. Examples of potential failures are given. A branch-and-bound algorithm for submovement extraction, capable of global nonlinear minimization (and hence capable of avoiding spurious decompositions), is developed and demonstrated.
Natural language processing-based knowledge management software, traditionally developed for security organizations, is now becoming commercially available. An informal survey was conducted to discover and examine current NLP and related technologies and potential applications for information retrieval, information extraction, summarization, categorization, terminology management, link analysis, and visualization for possible implementation at Sandia National Laboratories. This report documents our current understanding of the technologies, lists software vendors and their products, and identifies potential applications of these technologies.
The Z Refurbishment (ZR) Project is a program to upgrade the Z machine at SNL with modern durable pulsed power technology, providing additional shot capacity and improved reliability as well as advanced capabilities for both pulsed x-ray production and high pressure generation. The development of enhanced diagnostic capabilities is an essential requirement for ZR to meet critical mission needs. This report presents a comprehensive plan for diagnostic instrument and infrastructure development for the first few years of ZR operation. The focus of the plan is on: (1) developing diagnostic instruments with high spatial and temporal resolution, capable of low noise operation and survival in the severe EMP, bremsstrahlung, and blast environments of ZR; and (2) providing diagnostic infrastructure improvements, including reduced diagnostic trigger signal jitter, more and flexible diagnostic line-of-sight access, and the capability for efficient exchange of diagnostics with other laboratories. This diagnostic plan is the first step in an extended process to provide enhanced diagnostic capabilities for ZR to meet the diverse programmatic needs of a broad range of defense, energy, and general science programs of an international user community into the next decade.
If we are to build a supercomputer with a speed of 10{sup 15} floating operations per second (1 PetaFLOPS), interconnect technology will need to be improved considerably over what it is today. In this report, we explore one possible interconnect design for such a network. The guiding principle in this design is the optimization of all components for the finiteness of the speed of light. To achieve a linear speedup in time over well-tested supercomputers of todays' designs will require scaling up of processor power and bandwidth and scaling down of latency. Latency scaling is the most challenging: it requires a 100 ns user-to-user latency for messages traveling the full diameter of the machine. To meet this constraint requires simultaneously minimizing wire length through 3D packaging, new low-latency electrical signaling mechanisms, extremely fast routers, and new network interfaces. In this report, we outline approaches and implementations that will meet the requirements when implemented as a system. No technology breakthroughs are required.
This reference document provides summary information on the animal, plant, zoonotic, and human pathogens and toxins regulated and categorized by 9 CFR 331 and 7 CFR 121, 'Agricultural Bioterrorism Protection Act of 2002; Possession, Use and Transfer of Biological Agents and Toxins,' and 42 CFR 73, 'Possession, Use, and Transfer of Select Agents and Toxins.' Summary information includes, at a minimum, a description of the agent and its associated symptoms; often additional information is provided on the diagnosis, treatment, geographic distribution, transmission, control and eradication, and impacts on public health.
The essential oils of Juniperus scopulorum, Artemisia tridentata, and Salvia apiana obtained by steam extraction were analyzed by GC-MS and GC-FID. For J. scopulorum, twenty-five compounds were identified which accounts for 92.43% of the oil. The primary constituents were sabinene (49.91%), {alpha}-terpinene (9.95%), and 4-terpineol (6.79%). For A. tridentata, twenty compounds were identified which accounts for 84.32% of the oil. The primary constituents were camphor (28.63%), camphene (16.88%), and 1,8-cineole (13.23%). For S. apiana, fourteen compounds were identified which accounts for 96.76% of the oil. The primary component was 1,8-cineole (60.65%).
This paper analyzes what additional costs would be incurred in supporting dual-mode, i.e. both classified and unclassified use of the Institutional Computing (IC) hardware. The following five options are considered: periods processing in which a fraction of the system alternates in time between classified and unclassified modes, static split in which the system is constructed as a set of smaller clusters which remain in one mode or the other, re-configurable split in which the system is constructed in a split fashion but a mechanism is provided to reconfigure it very infrequently, red/black switching in which a mechanism is provided to switch sections of the system between modes frequently, and complementary operation in which parts of the system are operated entirely in one mode at one geographical site and entirely in the other mode at the other geographical site and other systems are repartitioned to balance work load. These options are evaluated against eleven criteria such as disk storage costs, distance computing costs, reductions in capability and capacity as a result of various factors etc. The evaluation is both qualitative and quantitative, and is captured in various summary tables.
High-resolution finite volume methods for solving systems of conservation laws have been widely embraced in research areas ranging from astrophysics to geophysics and aero-thermodynamics. These methods are typically at least second-order accurate in space and time, deliver non-oscillatory solutions in the presence of near discontinuities, e.g., shocks, and introduce minimal dispersive and diffusive effects. High-resolution methods promise to provide greatly enhanced solution methods for Sandia's mainstream shock hydrodynamics and compressible flow applications, and they admit the possibility of a generalized framework for treating multi-physics problems such as the coupled hydrodynamics, electro-magnetics and radiative transport found in Z pinch physics. In this work, we describe initial efforts to develop a generalized 'black-box' conservation law framework based on modern high-resolution methods and implemented in an object-oriented software framework. The framework is based on the solution of systems of general non-linear hyperbolic conservation laws using Godunov-type central schemes. In our initial efforts, we have focused on central or central-upwind schemes that can be implemented with only a knowledge of the physical flux function and the minimal/maximal eigenvalues of the Jacobian of the flux functions, i.e., they do not rely on extensive Riemann decompositions. Initial experimentation with high-resolution central schemes suggests that contact discontinuities with the concomitant linearly degenerate eigenvalues of the flux Jacobian do not pose algorithmic difficulties. However, central schemes can produce significant smearing of contact discontinuities and excessive dissipation for rotational flows. Comparisons between 'black-box' central schemes and the piecewise parabolic method (PPM), which relies heavily on a Riemann decomposition, shows that roughly equivalent accuracy can be achieved for the same computational cost with both methods. However, PPM clearly outperforms the central schemes in terms of accuracy at a given grid resolution and the cost of additional complexity in the numerical flux functions. Overall we have observed that the finite volume schemes, implemented within a well-designed framework, are extremely efficient with (potentially) very low memory storage. Finally, we have found by computational experiment that second and third-order strong-stability preserving (SSP) time integration methods with the number of stages greater than the order provide a useful enhanced stability region. However, we observe that non-SSP and non-optimal SSP schemes with SSP factors less than one can still be very useful if used with time-steps below the standard CFL limit. The 'well-designed' integration schemes that we have examined appear to perform well in all instances where the time step is maintained below the standard physical CFL limit.
Experimental data are compiled and reviewed for aerosol particle releases due to combustion in air of Plutonium (Pu). The aerosol release fraction (ARF), which is the mass of Pu aerosolized, divided by the mass of Pu oxidized, is dependent on whether the oxidizing Pu sample is static (i.e. stationary) or dynamic (i.e. falling in air). ARF data are compiled for sample masses ranging from 30 mg to 1770 g, oxidizing temperatures varying from 113 C to {approx}1000 C, and air flow rates varying from 0.05 m/s to 5.25 m/s. The measured ARFs range over five orders of magnitude. The maximum observed static ARF is 2.4 x 10{sup -3}, and this is the recommended ARF for safety studies of static Pu combustion.