Publications

Relatively straightforward changes in the optical design of a conventional optically recording velocity interferometer system (ORVIS) can be used to produce a line-imaging velocity interferometer wherein both temporal and spatial resolution can be adjusted over a wide range. As a result line-imaging ORVIS can be tailored to a variety of specific applications involving dynamic deformation of heterogeneous materials as required by the characteristic length scale of these materials (ranging from a few {micro}m for ferroelectric ceramics to a few mm for concrete). A line-imaging ORVIS has been successfully interfaced to the target chamber of a compressed gas gun driver and fielded on numerous tests in combination with simultaneous measurements using a dual delay-leg, ''push-pull'' VISAR system. These tests include shock loading of glass-reinforced polyester composites, foam reverberation experiments (measurements at the free surface of a thin aluminum plate impacted by foam), and measurements of dispersive velocity in a shock-loaded explosive simulant (sugar). Comparison of detailed spatially-resolved material response to the spatially averaged VISAR measurements will be discussed.

Plate impact, shock wave experiments provide a unique method to investigate the time-dependent mechanisms and the kinetics associated with pressure-induced phenomena, such as chemical reactions and phase transformations. The very rapid and well defined loading conditions associated with plate-impact experiments permit real-time examination of the shock-induced changes. Further, the ability to propagate the shock wave along various crystallographic directions provides the means to perform careful analysis of the stress and orientational dependence. Recently, an experimental method has been developed to observe real-time changes in the absorption transmission of materials, with 100 or 200 ps resolution, in single-event, plate impact shock experiments [1-4]. These data can provide useful information regarding the material under investigation. In particular, the dependence of the absorption edge on photon energy can distinguish between direct and indirect electronic transitions, and can provide an estimate of the band-gap energy of the material [5]. Along with ab-initio techniques to calculate the electronic structure of a crystalline system, this electronic information can be used to gain insight regarding the crystal structure. As described in Ref. [1,2,4] the wurtzite-to-rocksalt phase transition in cadmium sulfide (CdS) is well suited to investigation through the use of fast electronic spectroscopy; the wurtzite and rocksalt phases exhibit a direct and indirect band gap with band gap energies of 2.5 and 1.5-1.7 eV, respectively [6-8]. The intent of this work was to use picosecond electronic spectroscopy and ab-initio methods to examine the real-time structural changes that occur in the initial stages of the shock-induced wurtzite-to-rocksalt phase transition in single crystal CdS.

The pressure-induced phase transition in CdS was investigated using picosecond time-resolved electronic spectroscopy in plate impact shock wave experiments. Real-time changes in the electronic spectra were observed, with 100 ps time resolution, in single crystals of CdS shocked along the c and a axes to peak stresses between 35 and 90 kbar (above the phase transition stress of approximately 30 kbar measured in continuum studies). When shocked to stresses above approximately 50 kbar along the crystal c axis and 60 to 70 kbar along the crystal a axis, the crystals undergo a very rapid change in electronic structure, indicating that significant structural changes occur within the first 100 ps. These results, along with previous ns continuum measurements, make a strong case for a metastable state during the phase transition in shocked CdS. Ab-initio periodic Hartree-Fock calculations (with DFT correlation corrections) were employed to examine the compression of CdS and to determine a possible lattice structure for the proposed metastable structure. These results, along with details of the transformation kinetics and orientational dependence, will be discussed. Work supported by ONR.

In previous studies, ruby R-line shifts under shock compression and tension have been measured using the spontaneous luminescence from optically pumped samples. Signal intensities obtained through the use of this method are limited by the short time duration of the experiments (100 ns to several ps) in comparison to the long lifetime of the luminescence (approximately 3 ins). We have investigated the use of stimulated emission as a technique for measuring R-line shifts in shocked ruby crystals. Feasibility experiments were performed both at ambient conditions and under shock compression to 60 kbar using an experimental configuration similar to that used for time resolved ruby luminescence measurements in previous shock wave studies. Signal gain due to stimulated emission was observed, with gains ranging from 1.1 to 3.4, in agreement with calculations performed for the particular experimental configuration used. The present results make a good case for incorporating this technique to measure shock induced R-line shifts in ruby. Work supported by DSWA.