Publications

Results 100201–100225 of 100,993

Search results

Jump to search filters

Basic data report for drillholes H-17 and H-18 (Waste Isolation Pilot Plant-WIPP)

Mercer, J.W.; Snyder, R.P.

Drillholes H-17 and H-18 were drilled at the WIPP site to assess uncertainties in site hydrologic parameters and to serve as monitoring points for planned hydrologic tests. H-17 was drilled south of H-11 and east of P-17 to evaluate the existence of a high-permeability region in the Culebra Dolomite Member that had been indicated by groundwater-flow modeling and surface geophysical surveys. H-18 was drilled north of H-2 to help reduce the uncertainties of boundaries between high and low transmissivities and fluid density that had been identified by drilling and by modeling. 1 ref., 4 figs., 6 tabs.

More Details

Simulation fidelity in lightning penetration studies

Fisher, Richard J.

An extensive literature review has been conducted as part of an effort to quantify the fidelity of Sandia's lightning burn-through simulation technique. The dominant parameters affecting damage have been identified and are discussed. Two alternative techniques for qualitatively improving the Sandia simulation have been identified, but quantification of the correlation of the results of each with those of natural lightning awaits completion of further experimental work. A systematic set of laboratory experiments is proposed to assess the sensitivity of each technique to key simulation parameters. An available calibration linkage to natural lightning is the reproduction of damage spots that were created by lightning on a set of copper disks mounted on TV towers, and an attempt to do this is included in the proposed experiments. In order to reduce the uncertainties of this approach, more lightning-spot data are required, along with records of the flash currents that produced them. It is recommended that such data be acquired in conjunction with the Rocket-Triggered Lightning Program being conducted each summer at the Kennedy Space Center. 25 refs., 5 figs., 1 tab.

More Details

The inverse triax x-ray diode---an alternate reduced-endpoint-energy bremsstrahlung source

Harper-Slaboszewicz, V.J.; Poukey, J.W.; Stygar, W.A.; Fowler, W.E.; Peyton, B.

The inverse triax diode is a high power, low impedance electron diode which offers significant advantages over conventional electron diodes on short-pulse (<30 ns FWHM) high power x-ray simulators. Parametric calculations show that the radiation efficiency of the inverse triax is competitive with standard diodes fro mean photon energies below about 120 keV, and sometimes up to 150 keV. Particle-in-cell code simulations show the impedance behavior and flow pattern in the inverse triax with and without the presence of an anode plasma. The simulation results are used to suggest design rules for inverse triax diodes. Experimental results show good agreement with calculations of the impedance behavior and electron beam dynamics. Using inverse triax diodes, we have produced peak doses of 1.4 {times} 10{sup 11} rad(TLD)/s over 840 cm{sup 2} with a mean photon energy of 120 keV on SPEED and 3.1 {times} 10{sup 11} rad(TLD)/s over 3700 cm{sup 2} with a mean photon energy of 140 keV on Saturn. 20 refs., 16 figs.

More Details

FWP executive summaries: Basic energy sciences materials sciences programs

Samara, George A.

The BES Materials Science program at Sandia Albuquerque has the central theme of Scientifically Tailored Materials. The major objective of this program is to combine Sandia's expertise and capabilities in the areas of solid state sciences, advanced atomic-level diagnostics and materials-processing science to produce new classes of tailorable materials for the US energy industry, the electronics industry and for defense needs. Current research in this program includes the physics and chemistry of ceramics, the use of energetic particles for the synthesis and study of materials, high-temperature and organic superconductors, tailored surfaces for materials applications, chemical vapor deposition sciences, strained-layer semiconductors, advanced growth techniques for improved semiconductor structures and boron-rich very high temperature semiconductors. A new start just getting underway deals with the atomic level science of interfacial adhesion. Our interdisciplinary program utilizes a broad array of sophisticated, state-of-the-art experimental capabilities provided by other programs. The major capabilities include several molecular-beam epitaxy and chemical-vapor-deposition facilities, electron- and ion-beam accelerators, laser-based diagnostics, advanced surface spectroscopies, unique combined high-pressure/low-temperature/high-magnetic-field facilities, and the soon to be added scanning tunneling and atomic force microscopies.

More Details

Test Bed Concentrator No. 1 calorimetry results

Rawlinson, K.S.; Dudley, V.E.

Calorimetry was performed on Sandia National Laboratories' Test Bed Concentrator {number sign}1 (TBC-1) during late July and early August 1989. The purpose of the tests was to determine the total power available from the concentrator and the amount of the total power that can be focused through a 22-cm aperture plate located at the nominal focal point of the dish. The 22-cm aperture corresponds to the diameter of several reflux receivers that are currently under development, fabrication and testing at Sandia. The calorimeter test will allow the efficiency of the sodium reflux receivers to be calculated. The total power (normalized to 1000 W/m{sup 2}) available from TBC-1 is 66.4 kW into the 22-cm aperture plate. Within error limits, this power level is the same with or without the aperture plate. The power levels stated are for this time (July 1989) and will probably change as the mirrors further degrade. Since the last calorimetry tests were performed, the mirror facets have degraded significantly, and the results presented here support this effect. Finally, three of the 220 facets were missing. 3 refs., 5 figs., 2 tabs.

More Details

Hydrous metal oxide-supported catalysts: Part 2, Catalytic properties and applications

Dosch, R.G.

This report describes research leading to the development of new catalytic materials based on hydrous metal oxide (HMO) ion exchangers. Present in this part, the second of two parts, are results of catalyst-related research and application of the materials to catalytic reactions for direct coal liquefaction processes. HMO materials are inorganic ion exchangers, derived from the alkoxides of Ti, Zr, Nb, or Ta, that exhibit a number of properties applicable to the preparation of catalysts. Research on the catalytic properties of HMO's has focused on the hydrous titanium oxide (HTO) system. However, exploratory coal liquefaction experiments with hydrous niobium oxides (HNO's) and hydrous zirconium oxides (HZO's) have demonstrated that these HMO's also exhibit potential as coal liquefaction catalysts. Studies performed during the course of this research include (1) preliminary coal liquefaction and hydrotreating tests, (2) tests of hydrogenation, hydrodesulfurization, hydrodeoxygenation and hydrodenitrogenation activity using model compounds, (3) development of catalyst pretreatment and activation procedures, (4) modification of HTO supports with silicon, (5) preparation and testing of thin film HTO catalysts, (6) synthesis, characterization and evaluation of base and noble metal catalyst deactivation tests, and (9) exploratory tests of applications other than direct liquefaction. The versatility of the HTO system for synthesis of catalysts allows great potential for further improvements in activity and selectivity as well as tailoring of catalysts for specific processes. Research is continuing in these areas. 54 refs., 63 figs., 25 tabs.

More Details

Basic data report for drillholes H-14 and H-15 (Waste Isolation Pilot Plant-WIPP)

Mercer, J.W.; Snyder, R.P.

Drillholes H-14 and H-15 were drilled to investigate data gaps in the hydrologic hole distribution at the WIPP site. In addition to the information gained on the Culebra Dolomite Member, the holes yielded hydraulic and/or stratigraphic information on the Forty-niner, Magenta Dolomite, and Tamarisk Members of the Rustler Formation in an era where no such information was available. Hydraulic tests were also conducted on the lower part of the Dewey Lake Redbeds in H-14. A suite of geophysical logs was run on the drillholes and was used to identify different lithologies and aided in the interpretation of the hydraulic tests. 3 refs., 4 figs., 6 tabs.

More Details

An assessment of second-generation stretched-membrane mirror modules

Alpert, D.J.; Houser, R.M.; Heckes, A.A.; Erdman, W.W.

For more than 10 years, the US Department of Energy's Solar Thermal Program has pioneered the development of heliostats, mirrors that track the sun, for solar central-receiver power plants. The field of heliostats is the single most expensive part of such plants, so their cost must be as low as possible for the technology to be commercially successful. Recent efforts have focused on the development of heliostats that use stretched-membrane reflectors in place of the more familiar glass mirrors. In such heliostats, metal foils are stretched over both sides of a large-diameter metal ring. The reflective surface is a silvered-polymer film glued to the front membrane. A slight vacuum in the space between the two membranes is actively controlled to provide a concave, focused contour to the mirror, and in an emergency this space can be rapidly pressurized to defocus it. Because of their simplicity and lighter weight, stretched- membrane heliostats have the potential to cost significantly less than current glass-mirror designs. The first 50-m{sup 2} mirror modules, built under contract to Sandia in 1986, demonstrated that membrane heliostats could perform at least as well as heliostats using glass mirrors. Insights gained from Sandia's testing and evaluation of the first-generation units were incorporated into the designs of two improved 50-m{sup 2} mirror modules. The results of Sandia's evaluation show significant improvement in optical performance over the first-generation designs, especially in windy conditions. 22 refs., 29 figs.

More Details

PC-based information systems used in planning and coordinating the Building 823 exclusion from Tech Area 1

Tolendino, C.D.

This report describes the application of word processing, graphics and data base software to the task necessary for the exclusion of Building 823 from the secure technical area at Sandia National Laboratories. In particular, this report focuses on the development of the building floor plans layouts and the space/personnel data base which were used by management to plan and coordinate the project. Once the project is complete, these information systems will continue to be maintained by other personnel for administrative purposes. The software developed has potential applicability to other facilities where administrative monitoring or space assessment is required. 6 figs.

More Details

Description, operation, and maintenance information on joystick and closed-circuit television MPS-36 radar, Meppen Range, Federal Republic of Germany

Arndt, C.E.

Personnel from Stockpile Evaluation Program Division I, 7261, have been testing Joint Test Assemblies (JTAs) at Meppen Range, Federal Republic of Germany (FRG) since 1984. JTA trajectories were obtained from cinetheodolite film. The MPS-36 radar at Meppen Range is required to track the aircraft before bomb release to verify the release parameters for range safety and for the bomb trajectory after release. This is a difficult task because of the low-level approach of the aircraft. Division 7261 personnel asked Tonopah Test Range Department 7170 to assist in solving radar tracking problems. We recommended a new closed-circuit television system with a zoom lens and a force-operated, two-axis joystick. This system provides the operator a means of overriding the automode of the radar and manually positioning the radar antenna in azimuth (AZ) and elevation (EL). The joystick operator keeps the target (aircraft or bomb) centered in the TV picture by applying the correct pressure to the joystick. At the same time, the radar console operator maintains automatic range tracking by assisting the range gate through ground clutter using the control level of the range gate, as a rate-aid control in automatic mode. During the period May 8-17, 1989, the visual tracking equipment was installed in the Meppen radar. On May 16, 1989 a bomb dummy unit, loft maneuver was tracked successfully. The video, with time of day, was recorded for posttest, quick-look data. In the ten years of planned testing, a twenty-fold cost savings would be achieved with incorporation of the visual tracking capability to the MPS-36 radar, rather than providing radar beacons on each JTA. 8 figs.

More Details

Analysis of shell-rupture failure due to hypothetical elevated- temperature pressurization of the Sequoyah Unit 1 steel containment building

Miller, James E.

Sandia National Laboratories, as part of the Containment Integrity Programs under the sponsorship of the Nuclear Regulatory Commission (NRC), has developed analytical techniques for predicting the performance of light water reactor steel containment buildings subject to loads beyond the design basis. The analytical techniques are based on experience with large-scale steel containment model tests that provided important insights and experimental validation of the analytical methods. As a means of demonstrating these analytical techniques, the NRC asked Sandia to conduct a structural evaluation of an actual steel containment building. The objective of the analysis was to determine the actual pressure capacity and the mode, location, and size of failure, where a functional definition of failure is used. The purpose of this report is to document the calculations performed to determine the pressure limits for the shell- rupture mode of failure. General failure of the containment shell is predicted by application of a failure criterion to the results from finite element structural analyses. The failure criterion relates the calculated values of strain in the containment plates, due to internal-pressurization loading, to the ultimate strain limit of the steel. Included in the failure criterion are adjustments for factors inherent in finite element analysis, such as level of detail and element size of the finite element model and variations in material property data. Separate finite element models were used to evaluate the overall free-field behavior of the structure and the localized behavior at a specific penetration location. 18 refs., 68 figs., 10 tabs.

More Details

Posttest analysis of a 1:6-scale reinforced concrete reactor containment building

Weatherby, J.R.

In an experiment conducted at Sandia National Laboratories, 1:6-scale model of a reinforced concrete light water reactor containment building was pressurized with nitrogen gas to more than three times its design pressure. The pressurization produced one large tear and several smaller tears in the steel liner plate that functioned as the primary pneumatic seal for the structure. The data collected from the overpressurization test have been used to evaluate and further refine methods of structural analysis that can be used to predict the performance of containment buildings under conditions produced by a severe accident. This report describes posttest finite element analyses of the 1:6-scale model tests and compares pretest predictions of the structural response to the experimental results. Strain and displacements calculated in axisymmetric finite element analyses of the 1:6-scale model are compared to strains and displacement measured in the experiment. Detailed analyses of the liner plate are also described in the report. The region of the liner surrounding the large tear was analyzed using two different two-dimensional finite elements model. The results from these analyzed indicate that the primary mechanisms that initiated the tear can be captured in a two- dimensional finite element model. Furthermore, the analyses show that studs used to anchor the liner to the concrete wall, played an important role in initiating the liner tear. Three-dimensional finite element analyses of liner plates loaded by studs are also presented. Results from the three-dimensional analyses are compared to results from two-dimensional analyses of the same problems. 12 refs., 56 figs., 1 tab.

More Details

Preliminary drift design analyses for nuclear waste repository in tuff

Bauer, Stephen

The Yucca Mountain Project (YMP) is examining the feasibility of siting a repository for high-level nuclear waste at Yucca Mountain, on and adjacent to the Nevada Test Site (NTS). The proposed repository will be excavated in the Topopah Spring Member, which is a moderately fractured, unsaturated, welded tuff. Excavation stability will be required during construction, waste emplacement, retrieval (if required), and closure to ensure worker safety. The subsurface excavations will be subject to stress changes resulting from thermal expansion of the rock mass and seismic events associated with regional tectonic activity and underground nuclear explosions (UNEs). Analyses of drift stability are required to assess the acceptable waste emplacement density, to design the drift shapes and ground support systems, and to establish schedules and cost of construction. This paper outlines the proposed methodology to assess drift stability and then focuses on an example of its application to the YMP repository drifts based on preliminary site data. Because site characterization activities have not begun, the database currently lacks the extensive site-specific field and laboratory data needed to form conclusions as to the final ground support requirements. This drift design methodology will be applied and refined as more site-specific data are generated and as analytical techniques and methodologies are verified during the site characterization process.

More Details

Test plan for laboratory and modeling studies of repository and radionuclide chemistry for the Waste Isolation Pilot Plant

Brush, Laurence H.

This Test Plan describes laboratory and modeling studies of: the chemistry of brines that could enter Waste Isolation Pilot Plant (WIPP) disposal rooms; the effects of anoxic corrosion of metals in steel containers and the waste on the gas and H{sub 2}O budgets of the repository; the effects of microbial activity, especially microbial degradation of cellulosics in the waste, on the gas and H{sub 2}O budgets of the repository, the Eh and pH of any brine present, and the chemical behavior of radionuclides; the effects of radiolysis on the gas and H{sub 2}O budgets of the repository; the efficacy of backfill additives proposed to remove microbially produced CO{sub 2} or prevent the formation of H{sub 2} from anoxic corrosion, and their effects on repository chemistry; the chemical behavior of Pu, Am, Th, and U in WIPP brines; additional development of the EQ3/6 geochemical software package for use in predicting the behavior of silicates and radionuclides in brines. This Test Plan describes studies of the chemical behavior of the repository as currently designed, and the chemical behavior of radionuclides under these conditions. Addenda will discuss additional studies relevant to design modifications, especially reprocessed waste, and chemically hazardous waste constituents. 165 refs., 7 tabs.

More Details

A simple multicomponent fluid theory with accurate physics

Passman, S.L.

Generally multicomponent mixtures can exhibit a rich collection of phenomena. Thus it is to be expected that they will be described by complicated theories. In this paper we describe a relatively simple theory that is still theoretically correct, and discuss some of the phenomena that it exhibits. 12 refs.

More Details

Second-order nonlinear optical devices in poled polymers

Proceedings of SPIE - The International Society for Optical Engineering

Singer, K.D.; Holland, W.R.; Kuzyk, M.G.; Wolk, G.L.; Katz, H.E.; Schilling, M.L.; Cahill, P.A.

Guest-host poled polymer films have become an active area of research as potential candidates for second-order nonlinear optical and electro-optic devices. This interest derives mainly from their large nonlinear optical coefficients, ease of fabrication, and high optical quality. Progress has been rapid in producing stable, efficient materials, and in building demonstration devices. The second-order nonlinear optical properties arise from the orientational order induced in a collection of highly nonlinear molecules incorporated in a glassy polymer matrix. After reviewing the alignment physics, we present results of nonlinear optical measurements on a methacrylate polymer functionalized with a dicyanovinyl terminated azo dye. Device issues concerning nonlinear optical devices are described with particular attention to phase-matching. We present data on the demonstration of anomalous-dispersion phase matched second harmonic generation in dye solutions. We also present results on electro-optic modulators. © 1989 SPIE.

More Details

Effective waveform recorder evaluation procedures

Green, P.F.

The author describes a waveform-recorder evaluation system which is controlled by a Microvax II with instrumentation control through the IEEE-488 bus. Evaluation procedures are described with attention to the 'pathological cases' that can lead to significant misestimates of a digitizer's performance. The aim of these evaluation procedures is consistency with the new Trial Waveform Digitizer Standard generated by the Waveform Measurements and Analysis Committee appointed by the Instrumentation and Measurement Society of the IEEE. Methods are discussed for measuring the effective-bits performance of a waveform digitizer and determining differential nonlinearity.

More Details

Results of error correction techniques applied on two high accuracy coordinate measuring machines

Pace, C.; Doiron, T.; Stieren, D.; Borchardt, B.; Veale, R.; National Inst Of Standards And Technology, Gaithersburg (Usa)

The Primary Standards Laboratory at Sandia National Laboratories (SNL) and the Precision Engineering Division at the National Institute of Standards and Technology (NIST) are in the process of implementing software error correction on two nearly identical high-accuracy coordinate measuring machines (CMMs). Both machines are Moore Special Tool Company M-48 CMMs which are fitted with laser positioning transducers. Although both machines were manufactured to high tolerance levels, the overall volumetric accuracy was insufficient for calibrating standards to the levels both laboratories require. The error mapping procedure was developed at NIST in the mid 1970's on an earlier but similar model. The error mapping procedure was originally very complicated and did not make any assumptions about the rigidness of the machine as it moved, each of the possible error motions was measured at each point of the error map independently. A simpler mapping procedure was developed during the early 1980's which assumed rigid body motion of the machine. This method has been used to calibrate lower accuracy machines with a high degree of success and similar software correction schemes have been implemented by many CMM manufacturers. The rigid body model has not yet been used on highly repeatable CMMs such as the M48. In this report we present early mapping data for the two M48 CMMs. The SNL CMM was manufactured in 1985 and has been in service for approximately four years, whereas the NIST CMM was delivered in early 1989. 4 refs., 5 figs.

More Details

Merlin: A superglue for multicomputer systems

Maples, C.

Merlin is a memory based, interconnection system designed to provide very high-performance capability in a disturbed multicomputer environment. By using dynamically mapped reflective memory operations, the system creates a virtual memory environment which permits users to utilize both local and shared memory techniques. This mapped virtual memory approach permits selected information to be shared at high speeds and with relatively low latency. There is no software involvement in the actual sharing of information and the system automatically overlaps computation and communication, to the extent possible, on a word-by-word basis. Memory-to-Memory mapping allows Merlin to provide a uniform programming environment which is independent of interconnection topology, processing elements, and languages. 14 refs., 4 figs.

More Details

Studies of radionuclide sorption by clays in the Culebra Dolomite at the WIPP (Waste Isolation Pilot Plant) site, southeastern New Mexico

Siegel, Malcolm

In the most transmissive parts of the Culebra Dolomite, fluid flow is controlled by fractures. Gypsum (CaSO{sub 4} 2H{sub 2}O) and corrensite (a mixed chlorite/smectite) are the most abundant fracture-fill minerals. Radionuclide/clay interactions may be the dominant mechanism for radionuclide retardation. For this reason, the focus of this study is to examine the extent of the sorption of uranium and plutonium onto clays within the Culebra matrix and fractures. This paper describes several coordinated activities which will evaluate the potential retardation of radionuclide migration by sorption onto clays within the Culebras. These include characterization of the compositions of clays and groundwaters along the flow path; studies of the surface properties of simple reference clays and Culebra clays in dilute solutions and saline mixed electrolytes; development of a database of intrinsic equilibrium constants and specific-interaction parameters for calculations of the aqueous speciation of uranium and plutonium in Na-Cl-Ca-SO{sub 4}-CO{sub 3}-EDTA solutions which range in ionic strength from 0.1--4.0 molal; and measurement of surface complexation constants for uranium and plutonium in simple and mixed electrolyte solutions containing clays. 2 refs., 2 figs.

More Details

A Nickel/Hydrogen Battery for PV Systems

IEEE Aerospace and Electronic Systems Magazine

Bush, Donald M.

The nickel/hydrogen battery was developed in the early nineteen-seventies as an energy storage subsystem for commercial communication satellites. The advantages offered by nickel/hydrogen batteries, including long life, low maintenance and high reliability, make it very attractive for terrestrial applications such as stand-alone photovoltaic systems. The major drawback to the wider use of the nickel/hydrogen battery is its high initial cost. Sandia National Laboratories has placed cost-shared contracts with Comsat Laboratories and Johnson Controls, Inc., to reduce the cost, and a battery consisting of prismatic cells in a common pressure vessel has evolved. A 7-kWh battery has been on test at Sandia since January 1988 using a flat-plate photovoltaic array for charging. © 1990 IEEE

More Details

An iterative Bayes procedure for reliability assessment

Prairie, R.R.

In component reliability assessment programs, three major sources of data are available for reliability assessment: a development program, production data, and field test data. In practice, reliability assessments are required at the end of each stages, and a common method of assessment is to simply combine the test data and provide a pooled estimate. The method suggested in this paper is Bayesian in that the uncertainty about the unreliability is expressed by means of a prior distribution with a specified upper limit. The method is hierarchical Bayes in that the uncertainty about the limit of that prior distribution is also expressed by means of a prior distribution. The data from the development program are incorporated with the prior on the unreliability and with the prior on the upper limit of the prior to obtain a new prior on unreliability. The production data are then used to obtain a revised estimate of the unreliability as well as a modified value for the limit of the prior distribution. This same concept will be carried through when the field data are obtained. The result is a final Bayesian reliability assessment that is iterative in nature and incorporates in a sequential fashion data from each of the three stages common to a component development, production, and surveillance program. 4 refs., 2 tabs.

More Details

Thermal loads on tokamak plasma-facing components during normal operation and disruptions

Vacuum

Mcgrath, R.T.

Power loadings experienced by tokamak plasma-facing components during normal operation and during off-normal events are discussed. A model for power and particle flow in the tokamak boundary layer is presented and model predictions are compared to infrared measurements of component heating. The inclusion of the full three-dimensional geometry of the component and of the magnetic flux surface is very important in the modeling. Experimental measurements show that misalignment of component armour tile surfaces by only a millimeter can lead to significant localized heating. An application to the design of plasma-facing components for future machines is presented. Finally, thermal loads expected during tokamak disruptions are discussed. The primary problems are surface melting and vaporization due to localized intense heating during the disruption thermal quench and volumetric heating of the component armour and structure due to localized impact of runaway electrons. © 1990.

More Details

Mechanisms of selectivity loss during tungsten CVD (chemical vapor deposition)

Creighton, James R.

The tungsten subfluoride mechanism as well as other proposed mechanisms of selectivity loss are reviewed. To further demonstrate the viability of the tungsten subfluoride mechanism, we have extended the measurement of the tungsten subfluoride production rate down to 450{degree}C. We also report results from some preliminary experiments designed to identify the selectivity loss mechanism when elemental silicon is available for reaction. Comments regarding the origins of the insulator effect and selectivity loss for silane reduction are offered. 23 refs., 2 figs.

More Details
Results 100201–100225 of 100,993
Results 100201–100225 of 100,993
Top